Performance evaluation of dvb t2

Computer Engineering and Intelligent Systems www.iiste.org
ISSN 2222-1719 (Paper) ISSN 2222-2863 (Online)
Vol.5, No.7, 2014
60
PERFORMANCE EVALUATION OF DVB-T2
BROADCASTING NETWORK: A CASE STUDY OF DAR ES
SALAAM, TANZANIA
Lusekelo Kibona
MSc. student, Electronics and Telecommunication Engineering Department.
NM-AIST., Arusha,Tanzania.
kibonal@nm-aist.ac.tz
Dr. Anael Sam
Senior Lecturer, Electronics and Telecommunication Engineering Department.
NM- AIST., Arusha, Tanzania.
anael.sam@nm-aist.ac.tz
Abstract
DVB-T2 is the second generation of the digital terrestrial television broadcasting system which transmits
composite (compressed digital audio and video) signal and other data in an MPEG-4 transport stream, using
coded orthogonal frequency-division multiplexing (COFDM or OFDM) modulation. DVB-T2 uses multiple
MPEG-4 transport streams and have enhanced FEC and higher QAM (256-QAM) constellations. Tanzania
switched from analogue to Digital Video Broadcasting Terrestrial second generation (DVB-T2) in 2013, since
the official switching there has been complaints from the DVB-T2 users on the coverage and quality of service
provided. In this paper we evaluated the DVB-T2 performance and make the recommendations on the ways to
optimize the performance. Through measurements it has been observed that, the quality of coverage in some
areas (locations) is poor, so to improve the received signal strength coverage and quality we recommend the use
of enhanced Yagi-Uda antenna gain which is going to be designed.
Keywords: DVB-T2, Received Signal Strength Indicator (RSSI), Bit Error Rate (BER), Carrier to Noise Ratio
(CNR), Modulation Error Rate (MER), Polarization, Yagi-Uda antenna.
1. INTRODUCTION
Performance is a multi-faceted concept and it is conceptualized in many ways. Since networks stand at the heart
of the TV broadcast systems, then network performance can be perceived in business context in three
perspectives: customer perspective, technical perspective and system complexity perspective. It means
performance as interpreted by customers and network engineers and technicians; and in terms of network
components and complexity.
Analogue video broadcasting technology is being replaced by the digital video broadcasting ones. The common
problems found in analog video broadcasting are ghost images due to multipath distortion in the radio channel
and noise signals which degrades the quality of the analog video signal and sound which are all efficiently
solved by a digital television. The transition of analog to digital by the roll out of the Digital Video Broadcasting-
Terrestrial (DVB-T)[1] standards provides advantages in the exploitation of bandwidths, more robustness in
front to the noise and another series of advantages that are translated in a clear improvement of the image and the
sound, besides adding new applications for users like teletext services, email services in which the user is
capable to communicate with service provider from his television through the decoder.
The benefits of digital coding and transmission techniques allow perfect signal recovery in all the serviced areas
avoiding the effects of the wireless channel and noise. Considering the physical level of the communications, the
digital data sequences, which contain MPEG video, audio and other information streams, are transmitted using
Coded Orthogonal Frequency Division Multiplexing (COFDM) modulation. The information bits are coded,
interleaved, mapped to a Quadrature Amplitude Modulation (QAM) constellation and grouped into blocks. All
the symbols in a block are transmitted simultaneously at different frequency subcarriers using an Inverse Fast
Fourier Transform (IFFT) operation. The number of IFFT points, which can be either 2048 (2K) or 8192 (8K),
determines the transmission mode and the number of the available subcarriers in the transmission bandwidth.
Some of these subcarriers are not used to allow for guard frequency bands whereas others are reserved for pilot
symbols, which are necessary to acquire the channel information required for signal recovery.[2]
DVB-T2 is a 2nd
generation terrestrial broadcast transmission system developed by DVB project since 2006. The
main purpose is to increase capacity, ruggedness and flexibility to the DVB-T system. The emergence of DVB-
T2 is motivated by the higher spectral efficiency going along with DVB-T2 – be it for a transition from analogue
TV to DVB-T2, be it for a transition from DVB-T to DVB-T2. Higher spectral efficiency means that with the
same amount of spectrum, a larger number of programmes can be broadcast or the same number of programmes

Vol.5, No.7, 2014
61
broadcast with a higher audio/video quality or coverage quality. In addition improved source coding (MPEG-4)
is employed, the gain in broadcast transmission remarkable.[3]
The new technologies, like compression standard Moving Picture Experts Group 4 (MPEG-4) part 10, or
H.264/AVC (hereinafter called MPEG-4)[4] and the second generation of digital terrestrial broadcasting standard
(DVB-T2)[5], provide increased capacity and ruggedness in the terrestrial transmission environment. As
indicated in previous research [6], when considering the whole picture, it is evident that the latest technologies
besides technical benefits, increased capacity for new services and higher quality of service, bring also a higher
system cost. DVB-T2, second generation of terrestrial digital video broadcasting standard, promises performance
gains because of improved coding, modulation and multiple antenna technologies.[7]
The radio frequency spectrum is a limited natural resource that can be used to increase the efficiency and
productivity of a nation’s workforce consequently enhance the quality of life. Spectrum is used to provide a
wide variety of radio-communication services including; broad casting TV and sound, radio navigation,
aeronautical, maritime radio, satellite, radio location and amateur radio. In addition, the spectrum-based services
have become important inputs to a range of socio-economic activities such as security, education, health,
defense, transportation etc.
The number of Television and Radio broadcasting services are increasing tremendously and this cause some
problems in terms of quality of service provided to customers, for example in 2010 there were 10% of Tanzania’s
population complaining about the quality of service provided by broadcasting network. [8]
Since the official switching from analogue video broadcasting to DVB-T2 transmission, there has been an
increasing number of complaints from customers (End users) on the bad or scrambled reception of the TV
signals or sometimes lack of received signal at all. The source of complaints may be due to settings of the
transmission towers of the DVB-T2 operators, settings of the reception antennas, or geographical layout of the
region. Some important services like teletexting, email and subtitling have been missing since the launch of this
services.
The DVB-T2 transmitting antenna used in Tanzania by different multiplexers have the following specifications:
Frequency range 470-697MHz
VSWR <1.12
Gain (reference to λ/2) 11dB at midband
Impedance 50ohms
Maximum transmit power 3kW for vertical polarization antenna
Polarization Vertical polarization but they may be also used for
horizontal polarization like Star Media Limited they have set horizontal polarization in Arusha and Moshi with
maximum transmit power in those regions being 0.8kW
Note: The vertical polarization covers the large area compared with the horizontal polarization that’s why for
small coverage region the horizontal polarization is better than vertical polarization
The figure below shows the customer complaints as per TCRA annual report
Figure 1: Customer complaints [9]
Due to the nature of buildings and poor planning of the Dar es salaam city there are places where the signal
coverage are poor as stated before and the signals from transmitting towers at Kisarawe Hill and Makongo Juu
(for Star Media), Mikocheni (for BTL) and Tangibovu (for AAL) struggle to reach the houses or buildings in
some areas causing poor signal quality.

Vol.5, No.7, 2014
62
Figure 2: Diagram showing some tall buildings in Dar es Salaam as viewed from Posta PPF house
Figure 3: Diagram showing some rising buildings and forests in Mikocheni areas.
Another observations from survey shows that many outdoor directional antennas (Yagi-Uda antenna) are used
and which are placed on the roof approximately 4m from the ground, this may cause poor reception of signals
once heavy wind blows as the antenna direction may be twisted. But other buildings near by the transmitting
sites uses indoor monopole antennas but there are no any obstruction of signals from those towers. The receiving
antenna type used mostly are MISO (Multiple input single output)

Vol.5, No.7, 2014
63
Figure 4: Yagi-Uda antenna placed on the roof.
Also the presence of mountainous terrain in some areas like Changanyikeni (University of Dar es salaam),
Kimara Bonyokwa and other places causes some poor signal reception to the areas behind those terrain even
though taking Star Times as a case have erected their towers 132m high for Kisarawe transmission base and 83m
for Makongo Juu transmission base(At first it was constructed as a gap filler or a repeater in technical term but
now it is transmission base) but still the signals struggle to reach the receiving antennas in the mentioned areas
above.
2. PERFORMANCE PARAMETERS CONCEPTS AND THEORY
i.) CARRIER TO NOISE RATIO (C/N)
In communications, the carrier-to-noise ratio, often written CNR or C/N, is a measure of the received carrier
strength relative to the strength of the received noise or C/N is the ratio of the relative power level to the noise
level in the bandwidth of a system. High C/N ratios provide better quality of reception, and generally higher
communications accuracy and reliability, than low C/N ratios.
The C/N characterizes the robustness of transmission systems with regard to noise and interference. As such it is
used to determine the signal level required to receive a viable signal in noise and interference limited channels.
Subsequently, the determination of the C/N is of fundamental importance for network planning as it allows to
analyze if a carrier can still be recognized as such, or if it is obliterated by ambient and system noise. C/N
provides a value for the quality of a communication channel.[3]
The carrier-to-noise ratio (CNR) can be calculated through the following link budget formula:
Where:
B= Receiver noise bandwidth (MHz)
Table 3: Threshold data for CNR in different environment for three bands, for DVB-T2
only band IV and V applies.[10]
Threshold C/N [dB]
Environment Band III Band IV Band V
Rural 20 20 20
Suburban 22 22 22
Urban 24 24 24
The quality of the system is usually determined through BER plots against C/N.
Increased system robustness will also have a large impact upon SFN performance since a lower required C/N
will reduce the susceptibility for SFN self-interference. DVB-T2 will give the possibility to provide much higher
data rates than current DVB-T networks designed for portable or mobile reception.[3]

Vol.5, No.7, 2014
64
ii.) SIGNAL TO NOISE RATIO (SNR)
SNR is the ratio of the received signal strength over the noise strength in the frequency range of the operation.
Noise strength, in general, can include the noise in the environment and other unwanted signals (interference).
BER is inversely related to SNR, that is high BER causes low SNR. High BER causes increases packet loss,
increase in delay and decreases throughput. The exact relation between the SNR and the BER is not easy to
determine in the multi-channel environment. Signal to noise ratio (SNR) is an indicator commonly used to
evaluate the quality of a communication link and measured in decibels.
SNR is calculated as the ratio of average symbol power to noise power. Noise power includes anything that
causes the symbol to deviate from the ideal state position, including additive noise, distortion, and ISI (inter-
symbol-interference).[11]
Where: sum N is the summation of 1 to N and N is the result length in symbols. This indicates that the SNR and
the MER are closely related to each other.
CNR measurements can be converted to SNR by using the relation[12]:
Where for M-QAM in which for the case of DVB-T2 M= 64 or 256
iii.) BIT ERROR RATE (BER)
The BER, or quality of the digital link, is calculated from the number of bits received in error divided by the
number of bits transmitted.
In digital transmission, the number of bit errors is the number of received bits of a data stream over a
communication channel that has been altered due to noise, interference, distortion or bit synchronization errors.
The BER is the number of bit errors divided by the total number of transferred bits during a particular time
interval. BER is a unit less performance measure, often expressed as a percentage.
Noise affects the BER performance. Quantization errors also reduce BER performance, through incorrect or
ambiguous reconstruction of the digital waveform. The accuracy of the analog modulation process and the
effects of the filtering on signal and noise bandwidth also effect quantization errors.
The following expression gives the relationship between BER and the SNR for M-QAM in which for the case of
DVB-T2, M=64 or 256 which are square in nature;
Then the expression for BER is:
Where erfc stands for complementary error function and N stands for carrier mode i.e in the case of DVB-T2 in
Tanzania it is 8k.
iv.) MODULATION ERROR RATIO (MER)
The Modulation Error Ratio (MER) is a measure of the signal-to-noise ratio (SNR) in digital modulation
applications. This is used to determine system performance in communications applications. For example,
determining if an EDGE system conforms to 3GPP radio transmission standards requires accurate MER,
Minimum MER, and 95th percentile for the MER measurements.
For each received symbol, a decision is made as to which symbol was transmitted. The error vector is defined as
the distance from the ideal position of the chosen symbol (the center of the decision box) to the actual position of
the received symbol.[1]
This distance can be expressed as a vector
The sum of the squares of the magnitudes of the ideal symbol vectors is divided by the sum of the squares of the
magnitudes of the symbol error vectors. The result, expressed as a power ratio in dB, is defined as the MER.
MER is a measure of the SNR in a modulated signal calculated in dB and it is given by the following formula:

Vol.5, No.7, 2014
65
Where: I = In-phase measurement and Q = Quadrature phase measurements.
It should be reconsidered that MER is just one way of computing a "figure of merit" for a vector modulated
signal. Another "figure of merit" calculation is Error Vector Magnitude (EVM). MER and EVM are closely
related and one can generally be computed from the other .Also there is relationship between SNR and the EVM
as shown below:
In which there is inverse square law relationship existing between the two parameters.
v.) RECEIVER INPUT SIGNAL LEVELS (RSSI)
In telecommunications, received signal strength indicator (RSSI) is a measurement of the power present in a
received radio signal.[13]
RSSI (Received Signal Strength Indicator) is a common name for the signal strength in a wireless network
environment. It is a measure of the power level that a RF client device is receiving from an access point. The
closer the figure is to zero, the better. For example, RSSI of -65dBm is better than -85dBm. As a general
example, a good signal would be -50dBm, a reasonable would be -75dBm, and a bad one would be -90dBm,
while -100dBm would provide no service at all. [14]
The received signal levels is related to the CNR by the following relations:
In dB, ( )
Where for DVB-T2 in Tanzania as a case.
For carrier mode of 8k for 8MHz channels.
vi.) MODULATION TECHNIQUES
The DVB-T2 specification allows for time slicing, which is a well-known DVB-H feature. Time slicing reduces
the energy consumption of the receiving device. This is achieved by transmitting the services of a multiplex in
time blocks which allows the receiver to demodulate the signal only for a certain fraction of time in order to
receive a particular service. For the rest of the time the receiver may remain idle, it may use the remaining time
for the check of other frequency blocks or channels.[3]
64-QAM and 256-QAM are the modulations used in DVB-T2 technology and in Tanzania only 64-QAM
technique is used, delivering a gross data rate of 6 bits per symbol per carrier (i.e. 6 bits per OFDM cell) even
though there is a room for 256-QAM which increases this to 8 bits per OFDM cell.
3. MATERIALS AND METHODOLOGIES
Drive test measurements was conducted in different points and different places by considering the distance from
the tower in terms of coverage and considering the terrain nature(environment) and finally considering the
presence of tall buildings in the city which causes the non-line of sight to appear due to their penetration loss
caused by them. The measured parameters were Power received (RSSI), BER, MER and CNR. These parameters
were recorded after setting the upper limit parameter levels to gauge the relative strength of different areas
against the best values (E.g. the CNR were required to be measured up to 70dB, MER from 18dB, RSSI up to
116 dBµV and BER up to 10^-8). Also the measurement were taken under the following fixed condition:
ü STB signal input sensitivity of 25-100 dBµV
ü Antenna height 4m above the ground
ü Fixed transmitted power from the multiplexers
The measurements were taken in areas where people live and as said above the terrain level, vegetations and the
buildings(high rise buildings like Kariakoo, Posta, Upanga or low rise buildings like Kiwalani, Yombo kwa
Limboa, Tegeta, Kigamboni etc) were considered during the collections of the mentioned data. The areas visited
for the data collections includes: Bunju, Kilungule, Boko, Bahari beach, Kunduchi, Mbezi Beach, Tangibovu,
Jogoo, Rafia Bags, Salasala, Tegeta Kibaoni, Wazo Kiwandani, Tegeta Nyuki, Whie Sands, Makongo Juu, Goba,
External, Buguruni, Tazara, Kipawa, Karakata, Banana, Ukongo Magereza, Mombasa, Gongo la Mboto, Pugu
secondary, Kinyerezi, Tabata Bima, Tabata Segerea, Mbezi mwisho, Kimara Suka, Baruti, Corner, Ubungo
Msewe, Kurasini Bandarini, Mtoni kwa Azizi ally, Mtoni kichangani, Tandika Mwisho, Kiwalani Bombom,
Kiwalani Minazi mirefu, Jet Ally Mboa, Buza, Yombo, Yombo vituka, Duce, Bamaga Kijitonyama, Victoria,
Mwenge, Osterbay(CCBRT), Coco beach,Sarenda Bridge, Feri, Posta ya zamani, Kigamboni, Vijibweni,

Vol.5, No.7, 2014
66
Gezaulole, Mnazi Mmoja, Posta Mpya, Kariakoo sokoni, Kariakoo Mtaa wa Congo, Kariakoo Jangwani,
Muhimbili, Manzese Darajani,Shekilango, Sinza Uzuri, Sinza makaburini, Mbagala, Kibamba, Mbezi Msakuzi,
Mbezi makabe, Mpiji Majoe.
In those locations above the parameters were recorded for three multiplexers which are currently operating in
Tanzania and those includes Basic Transmission Limited(BTL) which formally were serving the Digitek and
Continental decoders, Agape associates Limited(AAL) which supplies the Ting decoders and Star Media Limited
which supplies the Star Times decoders.
The figure below shows the coverage map of Dar es Salaam city for three multiplexers.
Figure 5: The coverage map of DVB-T2 for Dar es Salaam city for both multiplexers where green indicates the
portable outdoor reception.
The analysis was done through MATLAB but the data were entered first in the Microsoft Exell and then
imported to MATLAB through commands.
4. RESULTS AND OBSERVATIONS
The analysis and evaluation of the performance was conducted using the relationships between parameters like
RSSI vs CNR relation, BER vs CNR relation for different multiplexers (BTL, AAL and Star Media).
It has been observed that high CNR ratios provide better quality of reception, and generally higher
communications accuracy and reliability, than low CNR ratios. So in the data obtained from the field
measurements, the presence of higher CNR indicates that the quality of signal is high. Also the low values of
BER indicates that the signal quality is good relative to the CNR. The following graphs indicates the relation
between RSSI with CNR and BER with CNR for BTL, AAL and Star Media.
i) RSSI against CNR
The following figure indicates the relationship between the Received Signal Strength Indicator and the Carrier to
Noise Ratio for BTL (Basic Transmission Limited which comprises of Digitek and Continental decoders), AAL
and Star Media.

Vol.5, No.7, 2014
67
Figure 6: A graph of RSSI vs CNR for BTL, AAL and Star Media
From the graph above the relationship between the RSSI and CNR is directly proportional relationship in some
locations because the increase in CNR goes with the increase in the RSSI but in other locations there is variation
between the two parameters in the sense that instead of RSSI values going high for high CNR values it
fluctuates meaning that it goes down or sometimes high e.g. for CNR of 35.1dBµV the RSSI value was found to
be 65.3dBµV while for CNR value of 35.9dBµV the RSSI value was found to be 45.5dBµV which shows that
there is a drop of 19.8dBµV, so the high CNR values are having relatively low RSSI values i.e signal received in
some areas are low for high CNR values which means that the quality of signal is still high in some areas which
are not well served by digital transmitter. In distributed non high rise buildings like Kiwalani, Mbagala, Gongo la
Mboto and the like, there is very good reception of signal levels because there is no reflections as there is good
LOS between the receiver and the digital transmitter. In the areas with low rise buildings like Mwenge, Mbezi
beach, Mbezi mwisho, Kimara and the like, there is good reception of signals with high quality signals observed
at Mwenge and Mbezi beach areas as the RSSI and the CNR are observed to be very high in the mentioned areas
and this is because the digital transmitter antenna is close to those areas as the transmitting antenna of BTL as a
case is located at Mikocheni near Mwenge with the direct LOS with very low noise or interference of signals. In
general the areas are well served by the digital transmitter, although some areas tend to get degraded signals
from high rise buildings in the neighborhood for example Kariakoo and Posta Mpya, those buildings which are
not tall buildings receive very low signals and sometimes receives nothing which means there is no coverage at
all due to blockage of signals caused by high rise buildings and this occurs for all multiplexers as it shown in the
figure 6 above. In some areas like Ubungo Msewe there is degraded signals due to adjacent terrain and low
altitude on which they lay so inorder to compensate for the degraded signals residents are advised to use high
gain aerials. Low lying areas and areas near the national stadium may require signal boosting because the signal
strength degrades due to propagation path loss caused by the distance from the transmitter to the receiver.

Vol.5, No.7, 2014
68
ii) BER against CNR
The following figure indicates the relationship between the Bit Error Rate (BER) and the Carrier to Noise ratio
(CNR) for BTL, AAL and the Star Media for the points taken at different locations in Dar es salaam.
Figure 7: A graph of BER vs CNR for multiplexers BTL, AAL and Star Media.
From the graph, it can be observed that there is variation between BER and CNR at different location for
different multiplexers, where in some areas or in the same location the values of BER differs for both
multiplexers where one multiplexer can have a very good signal quality in terms of BER then the other
multiplexer, for example at a CNR of approximately 23.5dBµV the value of BER for AAL is high compared to
the values of BER for the other multiplexers(BTL and Star Media) which means that the signal quality of AAL at
a 23.5dBµV is very poor as the high values of BER indicates that the signal is having more bits with errors even
though the CNR values are high. In general for the signal to have an excellent quality, the values of BER must
very low almost negligible for high values of CNR, example a signal at CNR of 34.8dBµV is very good in terms
of quality for all multiplexers because the BER is very low compared to the signal quality at 38.5dBµV where
the value of CNR is high but the BER value is also high for BTL as shown in figure 7 above.
iii) MER against CNR
The following figure indicates the relationship between the Bit Error Rate (BER) and the Carrier to Noise ratio
(CNR) for BTL, AAL and the Star Media for the points taken at different loactions in Dar es Salaam.

Vol.5, No.7, 2014
69
Figure 7: A graph of BER vs CNR for multiplexers BTL, AAL and Star Media.
From the graph it can be observed that, the MER and the CNR are directly proportional to each other in the
sense that when one parameter increases also the other increases which correlates with the theory, but in some
locations the value of MER was seen to be constant with the increased values of CNR which indicates that the
performance is the same in some areas despite the RSSI values for example when MER was 32dB, the values of
CNR went from 25dB up to approximately 43dB with MER being 32dB for all multiplexers(BTL, AAL and Star
Media). So in general in most locations the performance was observed to be good.
5. CONCLUSION
From the analysis above for DVB-T2 broadcasting network involving three multiplexers, most of the areas
within the primary service areas had good reliable signal (coverage and quality) apart from trouble spots that
have been in the location where digital transmitters do not cover them. High rise buildings in Dar es salaam
were observed to be causing signal obstructions to others for example areas like Mnazi Mmoja receives very low
signal due to its location because it is at the center of high buildings. It would be prudent if the use of shared
amplified resources hard wired to all high rise units would be incorporated in the building code. With favorable
terrain (Relatively flat) the strongest reliable signal was picked in those areas with non-rise buildings like
Mwenge areas, Kiwalani areas and others which are alike. Another observations from the
6. RECOMMENDATIONS AND FUTURE WORK
All high rise buildings (which tends to block the signals from the transmitting antenna to reach other resident
buildings) should be encouraged to adopt the shared resources of the all channels amplified TV signal wired to
all units in a block. Residents living in low altitude like Goba, Kimara Baruti are advised to use high gain aerials
to compensate for degraded signal due to low altitude.
Most of the aerials or receiving antenna are Yagi-Uda antenna which are directional (with high gain) in the sense
that they are positioned to receive signal in the direction of transmitting antenna so in some areas the signal from
transmitter reaches the receiver with very low values so an antenna with high gain will be capable to pick those
signals due to increased directivity and radiation pattern.
To solve this problem the design of the Yagi Uda antenna with an improved gain must take place or the use of the
quadrifilar helical antenna may serve the purpose because they are of very high gain and hence improve the
quality of the received signal.
Another recommendations is to use gap fillers (Repeaters or boosters) in places where the signals fade away
before reaching the receiving antenna. The areas like Bunju will be covered only when repeaters are placed.

Vol.5, No.7, 2014
70
Also the additional of transmitting power from 1.6kW will also help in improving the quality of coverage for
those relatively flat areas like Bunju and the like.
ACKNOWLEDGEMENT
The authors wishes to acknowledge the Nelson Mandela African Institution of Science and Technology (NM-
AIST) for their support during the preparation of this study.
REFERENCES
[1] E. TR101, "290 V1. 2. 1. Digital video broadcasting (DVB)," Measurement guidelines for DVB
systems, vol. 8, 2001.
[2] M. Mendicute, I. Sobrón, L. Martínez, and P. Ochandiano, "DVB-T2: new signal processing algorithms
for a challenging digital video broadcasting standard," Digital Video (In-Tech, 2010), pp. 185-206,
2010.
[3] B. Series, "Frequency and network planning aspects of DVB-T2," 2012.
[4] H. ITU-T RECOMMENDATION, "264 “Advanced Video Coding for Generic Audiovisual Services”,"
ISO/IEC, vol. 14496, 2003.
[5] E. ETSI, "302 755 V1. 1.1,“," Digital Video Broadcasting (DVB), pp. 1-167, 2008.
[6] A. Sugaris and I. Reljin, "DVB-T2 technology improvements challenge current strategic planning of
ubiquitous media networks," EURASIP Journal on Wireless Communications and Networking, vol.
2012, pp. 1-14, 2012.
[7] M. Tormos, C. Tanougast, A. Dandache, D. Masse, and P. Kasser, "Evaluation performance analysis of
DVB-T2 in a SFN network," in I/V Communications and Mobile Network (ISVC), 2010 5th
International Symposium on, 2010, pp. 1-4.
[8] T. REPORT, 2010.
[9] TCRA, "Annual report," Tanzania Tellecommunication Regulatory Authority, 2012.
[10] A. B. Authority, "Digital terrestrial television broadcasting planning handbook," ed: Camberra, 2005.
[11]
http://wireless.agilent.com/wireless/helpfiles/89600B/WebHelp/subsystems/digdemod/content/
digdemod_symtblerrdata_snr.htm, 2014.
[12] T. ETSI, "101 290 Digital Video Broadcasting (DVB)," Measurement guidelines for DVB systems, vol.
1, pp. 1987-1993, 2001.
[13] http://en.wikipedia.org/wiki/Received_signal_strength_indication, 2014.
[14] http://www.speedguide.net/faq_in_q.php?qid=418, 2014.

The IISTE is a pioneer in the Open-Access hosting service and academic event
management. The aim of the firm is Accelerating Global Knowledge Sharing.
More information about the firm can be found on the homepage:
http://www.iiste.org
CALL FOR JOURNAL PAPERS
There are more than 30 peer-reviewed academic journals hosted under the hosting
platform.
Prospective authors of journals can find the submission instruction on the
following page: http://www.iiste.org/journals/ All the journals articles are available
online to the readers all over the world without financial, legal, or technical barriers
other than those inseparable from gaining access to the internet itself. Paper version
of the journals is also available upon request of readers and authors.
MORE RESOURCES
Book publication information: http://www.iiste.org/book/
IISTE Knowledge Sharing Partners
EBSCO, Index Copernicus, Ulrich's Periodicals Directory, JournalTOCS, PKP Open
Archives Harvester, Bielefeld Academic Search Engine, Elektronische
Zeitschriftenbibliothek EZB, Open J-Gate, OCLC WorldCat, Universe Digtial
Library , NewJour, Google Scholar

Business, Economics, Finance and Management Journals PAPER SUBMISSION EMAIL
European Journal of Business and Management EJBM@iiste.org
Research Journal of Finance and Accounting RJFA@iiste.org
Journal of Economics and Sustainable Development JESD@iiste.org
Information and Knowledge Management IKM@iiste.org
Journal of Developing Country Studies DCS@iiste.org
Industrial Engineering Letters IEL@iiste.org
Physical Sciences, Mathematics and Chemistry Journals PAPER SUBMISSION EMAIL
Journal of Natural Sciences Research JNSR@iiste.org
Journal of Chemistry and Materials Research CMR@iiste.org
Journal of Mathematical Theory and Modeling MTM@iiste.org
Advances in Physics Theories and Applications APTA@iiste.org
Chemical and Process Engineering Research CPER@iiste.org
Engineering, Technology and Systems Journals PAPER SUBMISSION EMAIL
Computer Engineering and Intelligent Systems CEIS@iiste.org
Innovative Systems Design and Engineering ISDE@iiste.org
Journal of Energy Technologies and Policy JETP@iiste.org
Information and Knowledge Management IKM@iiste.org
Journal of Control Theory and Informatics CTI@iiste.org
Journal of Information Engineering and Applications JIEA@iiste.org
Industrial Engineering Letters IEL@iiste.org
Journal of Network and Complex Systems NCS@iiste.org
Environment, Civil, Materials Sciences Journals PAPER SUBMISSION EMAIL
Journal of Environment and Earth Science JEES@iiste.org
Journal of Civil and Environmental Research CER@iiste.org
Life Science, Food and Medical Sciences PAPER SUBMISSION EMAIL
Advances in Life Science and Technology ALST@iiste.org
Journal of Biology, Agriculture and Healthcare JBAH@iiste.org
Journal of Food Science and Quality Management FSQM@iiste.org
Journal of Chemistry and Materials Research CMR@iiste.org
Education, and other Social Sciences PAPER SUBMISSION EMAIL
Journal of Education and Practice JEP@iiste.org
Journal of Law, Policy and Globalization JLPG@iiste.org
Journal of New Media and Mass Communication NMMC@iiste.org
Journal of Energy Technologies and Policy JETP@iiste.org
Historical Research Letter HRL@iiste.org
Public Policy and Administration Research PPAR@iiste.org
International Affairs and Global Strategy IAGS@iiste.org
Research on Humanities and Social Sciences RHSS@iiste.org
Journal of Developing Country Studies DCS@iiste.org
Journal of Arts and Design Studies ADS@iiste.org

Performance evaluation of dvb t2

More Related Content

What's hot (17)

Similar to Performance evaluation of dvb t2 (20)

More from Alexander Decker (20)

Recently uploaded (20)

Performance evaluation of dvb t2