E NERGY - E FFICIENT P ATH C ONFIGURATION M ETHOD FOR DEF IN WSN S

International Journal on Information Theory (IJIT),Vol.4, No.2, April 2015
DOI : 10.5121/ijit.2015.4202 9
ENERGY-EFFICIENT PATH CONFIGURATION
METHOD FOR DEF IN WSNS
Jae Kwon Lee1
, Su Man Nam2
and Tae Ho Cho3
1, 2, 3
School of Information and Communication Engineering Sungkyunkwan University, Su-
won, 440-476, Republic of Korea
ABSTRACT
In wireless sensor networks (WSNs), sensor nodes have stringent energy and computation requirements.
Since they are left unattended, an adversary can generate false report attacks through compromised nodes.
This would result in an increased number of verifications to filter these reports, causing waste of scarce
energy resources. In this paper, we propose energy-efficient path configuration method for dynamic en-
route filtering (EDEF), which uses fuzzy logic to select the forwarding node(s). In order to cater to
compromised nodes and to detect and filter the false reports, we create alternative paths. Our proposed
method selects forwarding nodes based on the key content of neighbor nodes, the number of neighbor
nodes, and the residual energy. Auth-keys are distributed randomly from the global key pool. Simulation
results demonstrate the effectiveness of our proposed method with up to 8.2% energy efficiency as
compared to the dynamic en-route filtering (DEF) scheme.
KEYWORDS
Sensor network, en-route filtering, false report attack, fuzzy logic, detection power, next-hop, energy-
efficiency
1. INTRODUCTION
Wireless sensor networks (WSNs) are being used in numerous applications to carry out tasks
without human intervention [1]. However, WSNs suffer energy and computation limitations and
are left unattended for longer periods of time [2, 3]. Sensor nodes can be compromised and used
by an adversary to generate false report attacks. These false report attacks would result in an
increased number of verifications to filter these reports, thereby causing a reduced network-
lifetime [4]. The dynamic en-route filtering (DEF) was proposed by Yu et al. to defend a false
report injection attack [5]. Various schemes as the statistical en-route filtering (SEF),
commutative cipher based en-route filtering (CCEF) and probabilistic voting-based filtering
(PVFS) as well as the DEF were proposed for the same purpose [6-15]. However, the DEF is
capable of performing best in a dynamic network.
The DEF is basically configured as a cluster-based network. The DEF is divided into three major
phases: key pre-distribution, key dissemination, and report forwarding. The key pre-distribution
phase is executed when the sensor network is first set up. The key dissemination phase is
executed whenever the network topology is changed. The report forwarding phase is executed
whenever a report is generated by a cluster-head (CH). The DEF verifies the validity of a report
using a message authentication code (MAC). To select the next-hop forwarding node, the DEF
does not specify the selection criteria which can be changed by applications. In the proposed
method, we use the key content of neighbor nodes, the number of neighbor nodes, and the
residual energy as criteria for the selection of forwarding nodes. The major contributions of our
scheme are as follows:

10
• Early false report detection power
• Considerable energy improvement over the original scheme
• Fuzzy logic for evaluation of the next-hop
In this paper, in order to use next-hop forwarding nodes, we use the above selection criteria with
fuzzy logic in our implementation. Whenever the network topology changes, criteria for the
selection of forwarding nodes is applied at the key distribution phase. The parameters of the fuzzy
input are as follows: the node with multiple keys, the number of neighbor nodes, and the residual
energy. We determine the next-hop forwarding node through these input values. Any time the
topology of a network is changed, the energy-efficient path configuration method for DEF
(EDEF) executes the key dissemination phase, similar to the DEF for a dynamic network.
Whenever the key dissemination phase is performed, the next-hop node is selected through fuzzy
logic in the EDEF.
The EDEF was organized as a cluster-based sensor network similar to DEF. The cluster-based
network can avoid redundant data transmission [16, 17]. A base station (BS) calculates a fuzzy
value for each node since the sensor network information is handled by the BS. Each CH
determines the forwarding node through the fuzzy values of the neighbor nodes. Using this
information, we demonstrate the EDEF, which results in greater energy efficiency and detection
power in comparison with the DEF.
This paper is organized as follows: in a section 2, we describe the original DEF in detail. In
section 3, we explain the motivation, overview, and the proposed EDEF in detail. Section 4
discusses assumptions and the performance comparison; and the conclusion is given at the end of
the paper.
2. BACKGROUND
In this section, we present related background work.
2.1. Dynamic En-route Filtering Scheme
The DEF was proposed by Yu et al. to defend the false report injection attack in WSNs. The DEF
is composed of a cluster, as in Figure 1, where the nodes v1 ~ v4 represent a sensor node in the
cluster, and a black dot (v3) represents a compromised node. Basically, a CH aggregates the
detected reports of all nodes. The CH then generates a message to forward to the BS. Finally, the
CH sends the message to the BS. Any can be compromised node, including the CH. Additionally,
all nodes can be a forwarding node on a path of the BS.
Figure 1. A simple figure of the DEF
DEF is briefly divided into three phases (key pre-distribution, key dissemination, and report
forwarding) as shown in Figure 2. First, the network is configured and then a key is pre-

11
distributed. The key pre-distribution phase is executed once when the network is first configured.
Following this, the key dissemination phase of a key distribution occurs, which executes the
report forwarding phase. The key dissemination phase would then be executed again based on the
fixed period that is determined at the cluster. The report forwarding phase could be executed at
every round at the each forwarding node.
Figure 2. Three phases of the DEF
Figure 3. Key deployment of each node
Figure 3 shows that node v_i was loaded with the keys in the key pre-distribution phase. Here, the
auth-key chain is generated using the seed key and a hash function. This auth-key is then the first
of the auth-key chain. The y-key would then be randomly selected as a fixed number in the global
key pool. The z-key is then randomly selected as one key of the global key pool; this key is not
duplicated with any other keys. The auth-keys of the node in a cluster are aggregated with the CH
to generate the message, K(n), as in Figure 4. Then the CH sends the message to q number of
forwarding nodes. In the report forwarding phase, a report is aggregated from a node of the
cluster as in the key dissemination phase, and then the CH sends an aggregating message to the
BS. In the DEF, the report is verified with the MAC. This MAC is generated using the event and
auth-key in each node. The DEF re-executes the key dissemination phase and the report
forwarding phase according to a fixed rule.

12
Figure 4. Auth-key is sent to the forwarding node.
The report forwarding phase is newly executed by the forwarding node whenever an event is
generated. The report forwarding phase is executed to forward a newly generated event in report
format to the BS. The key dissemination phase is re-executed for key re-dissemination in case of
network topology changes as such changes can change the nodes of the cluster. It is then
necessary to re-disseminate the node information over the changed cluster. Therefore, the key
dissemination phase can be re-executed.
3. PROPOSED METHOD
3.1. Motivation
When we select the next forwarding node, the DEF does not specify some factors because,
according to various applications, the determining factors may be different. The DEF selects the
next node by combining factors such as the available of energy, the link quality, the speed of
energy consumption, and so on. The DEF does not consider the energy-efficiency of the
forwarding node. The network, therefore, can easily consume the energy of the node. Energy
depletion of a node produces a decrease in the network-lifetime. We evaluated the selection of a
forwarding node using fuzzy logic; this scheme shows efficiency up to 5% [18]. However, we
decide that the 5% efficiency is a weak influence. Hence, we changed to new factors and
evaluated these factors. According to this, we can have more efficient than before factor through
new factors.
3.2. Overview
When determining the next forwarding node in the DEF, we select the next node using the fuzzy
logic from the proposed EDEF. We used three input factors in fuzzy logic: 1) key content, 2) the
number of neighbor nodes, and 3) the residual energy of each candidate node. We can calculate
the result using these three input factors. We then determine the next node based on the result. If
the report reaches the BS in every round, the BS calculates the result of the nodes in the entire
network using fuzzy logic. A CH then determines the next forwarding node on a path to the BS.
We can foresee an increase in the efficiency between the EDEF and the DEF through the
Travelled hop count of the false reports.
3.3. Proposed method
The EDEF uses fuzzy logic in the dissemination phase of the DEF. This is more effective for
extending the network-lifetime. The EDEF has three input factors for the fuzzy logic. The three
input factors are as follows: 1) the key content (KN), 2) the number of neighbor node (NN), and
3) the residual energy (RE) of each contender. When we select the next forwarding node, we use

13
the result from the above three factors. Each input factor is divided into three detailed phases,
allowing 27 different possible results (=3×3×3). We can select the optimum forwarding node
based on 27 different results. The auth-key is disseminated to multiple paths because of the
possibility of 1) data loss, 2) verification, or 3) dynamic topology. The DEF pre-determines the
number of forwarding nodes as „q‟. The DEF then selects q as the forwarding node. In case of 'q
= 2,' two forwarding nodes are selected at the BS. When the q possible forwarding nodes are
selected, the final forwarding node is chosen using fuzzy logic. Fuzzy rule-based system has been
used to approximate reasoning for an imprecision of a data or an uncertainty in reasoning
processes [19].
3.3.1. Further Subsections
The input factor for fuzzy logic and the resulting value are as follows:
KN= {LITTLE, MEDIUM, FULL}
NN= {FEW, MIDDLE, CROWDED}
RE= {LOW, MEDIUM, ENOUGH}
R= {VERY BAD, BAD, NORMAL, GOOD, VERY GOOD}
Each input value is divided into three phases (as shown above), and the resulting value is divided
into five parts. Details of the input factors that are used for the fuzzy logic are as follow.
 The key content of node To begin with, the following is the reason for the key content of
node. When a key is disseminated in the DEF, a CH aggregates the keys belonging to each
node, and forwards the aggregate to the node on a path in a fixed hop count. We use these
keys to verify the forwarded report. At this time, if the node was received in duplicate, the
node has multiple keys that are compared with the others. A node with many keys means that
it can be used in multiple clusters. According to this, when the DEF sends a report, the node
with many keys is more efficient than the others.
 The number of neighbor nodes The number of neighbor nodes is selected as the next input
factor so that the message can be delivered to the zones of many candidate nodes. In order to
broaden the selection range, the zones of many candidate nodes are selected. If there are few
candidate nodes, then the selection pool is reduced. Therefore, we broaden the selection
range, in order to obtain a more efficient node.
 The residual energy In the end, the residual energy is the current usable energy of a
candidate node and is an input factor. When a node with less energy is compared with a node
with a lot of energy, if the node with less energy is selected, the entire network-lifetime is
quickly shortened. According to this, if we select the node with a lot of energy, it can sustain
the network-lifetime. Selecting the node with a lot of energy can then steadily consume the
energy of the whole network. Accordingly, we select it as an input factor for the fuzzy logic.
Figure 5 presents a process in which a CH selects the q forwarding node through a fuzzy rule-
based system. When the q is determined to be '2,' as in the figure, it receives the respective KN,
NN, and RE values of u_1,u_2,〖 and u〗 _3; it then selects a node based on the two highest
ranking results.

14
Figure 5. Fuzzy rule-based system for node selection
A fuzzy computation is computed at a BS; the BS has information for all nodes. The BS
determines that each CH selects a node using the fuzzy rule-based system. This is re-computed
every cycle in order to forward a message.
Figure 6 presents the membership function of the fuzzy input values and result values.
Figure 6. Fuzzy membership function of input values and the result values.

15
Some of the rules are shown below.
Table 1. Some of the fuzzy rules.
R1 : IF KN IS LITTLE R5 : IF KN IS LITTLE
AND NN IS FEW AND NN IS FEW
AND RE IS LOW AND RE IS HIGH
THEN R IS VERY BAD THEN R IS BAD
R2 : IF KN IS LITTLE R6 : IF KN IS FULL
AND NN IS MIDDLE AND NN IS MIDDLE
AND RE IS LOW AND RE IS MEDIUM
THEN R IS VERY BAD THEN R IS GOOD
AND NN IS CROWDED AND NN IS MEDIUM
AND RE IS LOW AND RE IS LOW
THEN R IS BAD THEN R IS NORMAL
AND NN IS FEW AND NN IS MIDDLE
AND RE IS MEDIUM AND RE IS ENOUGH
THEN R IS VERY BAD THEN R IS VERY
GOOD
3.3.2. The base data for the EDEF
Figure 7. Average of the Travelled hop count for 'q=3'
Figure 7 shows an average of the Travelled hop count for „q = 3‟ according to the attack ratio. It
is expected that the EDEF can detect a false report earlier than the original DEF. Therefore, we
experimented further and obtained the following results.

16
Figure 8. Difference in the total Travelled hops between the EDEF and the DEF.
Figure 9. A filtered report ratio
Figure 8 shows the Travelled hop count without filtering a false report. The following is the
Travelled hop count equation. The hop count is the difference between the value of the Travelled
hop count without filtering using a DEF and the value of the Travelled hop count without filtering
using the proposed method.
Total Travelled hops = Travelled hops in the DEF – Travelled hops in the proposed method
Additionally, Figure 9 presents a graph of the EDEF efficiency against the DEF. As shown in the
figure, greater efficiency is seen with increases in 'q'. According to Figure 8 and 9, the proposed
method is faster than the existing method. Accordingly, we progressed to more detailed
experiments; in the following section, we verify the energy consumption efficiency compared
with the DEF.
4. PERFORMANCE EVALUATION
In this section, we will present the energy-efficiency of the EDEF in comparison with the original
DEF under same environmental setup.

17
4.1. Experiment setup
We assume that the BS has information of all nodes in the sensor network. Every CH has the
information about the key content, the number of neighbor nodes, and the residual energy of all
nodes in its cluster.
 The sensor field size is 200 x 200 (m2), and the total number of nodes are 1000, consisting of
100 clusters which are randomly distributed where each cluster consists of 10 nodes.
 Each node picks l = 2 y-keys and one z-key, where the size of the y-key and z-key pool
consists of 1000 keys.
 Each node forwards the message K(n) to q selected downstream neighbor nodes, until K(n)
reaches to the BS or has been forwarded by hmax hop. Here, hmax = 10. Hence, we adopted
Hill Climbing method [20] to forwards the message K(n).
 Each aggregated report contains 10 MACs, and there are at most 10 compromised nodes in
each cluster.
 The size of a message is 36 bytes, and 16.25/12.5μJ is consumed for transmitting/receiving a
byte [8].
 Each node has fuzzy result values which are calculated by the BS. The BS then broadcasts
the q and fuzzy result of each node to entire network through authenticated broadcast (e.g.,
using μTESLA [21])
 To simulate a dynamic network, we apply a simple ON/OFF operation node, where each
node is typically switched to ON or OFF mode.
 The DEF and the EDEF adopted a GPSR routing protocol.
4.1. Experiment results
In the above assumption, the announced sensor field size and total number of nodes are the same,
and a CH generates 100 reports during each cycle. Each key pool has 1000 keys. The experiment
was performed with an increasing ratio of false reports and a changing q value. The figure below
shows the efficiency of the proposed method compared with DEF according to the attack ratio.
Figure 10. Total energy efficiency of each „q.‟

18
The figure above shows the energy-efficiency for each „q‟ against the DEF. Each q shown has
efficiency between 4.84% and 6.12%. The greater the number of q or the more complex the
sensor network, the greater is the efficiency. The reason why the efficiency increases as q
increases is because a large, q has a larger number of cases. Therefore, this demonstrates that
selection using the fuzzy system is more efficient than the DEF.
Figure 11. Energy efficiency versus the attack ratio.
By measuring the value for each q, the results show that greater the value of q, the greater the
efficiency as compared to the DEF. An increasing value of q means that more messages are
created to send to the next forwarding nodes. As can be seen in the above figure, when the value
of q is 5, the efficiency is greater than 8%. The attack rate of the 100 generated reports is the ratio
of false reports. The efficiency ratio of false reports of enemy all the time and when there are
many showed similar performance. However, they showed a difference in the 30% to 70%
section. In fact, a false report injection attack cannot occupy the whole message. The results are
confirmed because they were generated for the above experiment. However, the experiment does
not include the number of cases in a real sensor network. However, if the number of q is changed
according to the environment of the DEF, the proposed method showed greater efficiency through
the above experiment.
The figure above compares the efficiency of the proposed method with the DEF with regard to
the total number of filtered false reports in one hop. This graph compares the number of filtered
reports within one hop in the proposed method with that in the DEF. The figure above shows a
slightly more efficient detection for the proposed method compared with the DEF.
5. CONCLUSIONS
In this study, the aim was to increase energy-efficiency with increased detection power by
considering alternative paths. We have presented EDEF, a fuzzy-based next-hop selection
scheme. In order to select the forwarding nodes in next-hop and to distribute keys, we use fuzzy
logic. Our method can detect more false reports as compared to the DEF scheme. By detecting the
false reports early, our method demonstrated considerable energy improvement without
compromising the security of the original scheme.

19
In conclusion, the EDEF has excellent detection power compared with the DEF and improves the
energy efficiency in order to sustain the network-lifetime for a long time. In the future, we can
further enhance the performance through a simulation with suitable fuzzy function values.
ACKNOWLEDGEMENTS
This research was supported by Basic Science Research Program through the National Research
Foundation of Korea (NRF) funded by the Ministry of Education, Science and Technology (No.
2013R1A2A2A01013971)
REFERENCES
[1] I. F. Akyildiz, Weilian Su, Y. Sankarasubramaniam, & E. Cayirci, (2002) "A survey on sensor
networks," Communications Magazine, IEEE, Vol.40, No.8, pp.102-114.
[2] Jing Deng, R. Han, and S. Mishra, (2005) "Countermeasures against traffic analysis attacks in
wireless sensor networks," Security and Privacy for Emerging Areas in Communications Networks,
pp.113-126.
[3] Moog Inc., "MICAz data sheet," Moog Crossbow, http://www.xbow.com.
[4] C. Karlof and D. Wagner, (2003)"Secure routing in wireless sensor networks: Attacks and
countermeasures," Sensor Network Protocols and Applications, 2003. Proceedings of the First IEEE.
2003 IEEE International Workshop on, pp.113-127.
[5] Zhen Yu and Y. Guan, (2010) "A dynamic en-route filtering scheme for data reporting in wireless
sensor networks," Networking, IEEE/ACM Transactions on, Vol.18, No.1, pp.150-163.
[6] Hao Yang and Songwu Lu, "Commutative cipher based en-route filtering in wireless sensor
networks," Vehicular Technology Conference, 2004. VTC2004-Fall. 2004 IEEE 60th, pp.1223-1227.
[7] Feng Li, Avinash Srinivasan, and Jie Wu, (2008) "PVFS: A probabilistic voting-based filtering
scheme in wireless sensor networks," International Journal of Security and Networks, Vol.3, No.3,
pp.173-182.
[8] Fan Ye, Haiyun Luo, Songwu Lu, and Lixia Zhang, "Statistical en-route filtering of injected false data
in sensor networks," Selected Areas in Communications, IEEE Journal on, Vol.23, No.4, pp.839-850.
[9] Jianzhong Li, Lei Yu, Hong Gao, and Shuguang Xiong, "Grouping-enhanced resilient probabilistic
en-route filtering of injected false data in WSNs," Parallel and Distributed Systems, IEEE
Transactions on, Vol.23, No.5, pp.881-889.
[10] T. P. Nghiem, Sang Jin Lee, and Tae Ho Cho, (2009) "An energy-aware fuzzy-based en-route filtering
scheme in wireless sensor networks," Future Networks, 2009 International Conference on, pp.28-32.
[11] A. S. Uluagac, R. A. Beyah, and J. A. Copeland, (2010) "Time-based DynamiC keying and en-route
filtering (TICK) for wireless sensor networks," Global Telecommunications Conference
(GLOBECOM 2010), 2010 IEEE, pp.1-6.
[12] Wensheng Zhang and Guohong Cao, (2005) "Group rekeying for filtering false data in sensor
networks: A predistribution and local collaboration-based approach," INFOCOM 2005. 24th Annual
Joint Conference of the IEEE Computer and Communications Societies. Proceedings IEEE, pp.503-
514 vol. 1.
[13] Hae Young Lee and Tae Ho Cho, (2006) "Key inheritance-based false data filtering scheme in
wireless sensor networks," Distributed Computing and Internet Technology, Lecture Notes in
Computer Science, vol.4317, pp.116-127.
[14] Hae Young Lee and Tae Ho Cho, (2008) "Fuzzy logic based key disseminating in ubiquitous sensor
networks," Advanced Communication Technology, 2008. ICACT 2008. 10th International Conference
on, pp.958-962.

20
[15] Ting Yuan, Shiyong Zhang, Yi-ping Zhong, and Jianqing Ma, (2008) "KAEF: An en-route scheme of
filtering false data in wireless sensor networks," Performance, Computing and Communications
Conference, 2008. IPCCC 2008. IEEE International, pp.193-200.
[16] J. N. Al-Karaki and A. E. Kamal, (2004) "Routing techniques in wireless sensor networks: A survey,"
Wireless Communications, IEEE, vol.11, no.6, pp.6-28.
[17] K. Akkaya and M. Younis, (2005) "A survey on routing protocols for wireless sensor networks," Ad
Hoc Networks, vol.3, no.3, pp.325-349, 5.
[18] Jae Kwon Lee and Tae Ho Cho, (2012) "Selecting next hop nodes for energy efficiency in dynamic
filtering based WSNs using fuzzy system," Information Science and Digital Content Technology
(ICIDT), 2012 8th International Conference on, pp.674-677.
[19] H. S. N. Serrano, (2007) "Landing site selection using fuzzy rule-based reasoning," Proc. ICRA,
pp.4899-4904.
[20] D.B. Skalak, (1994) "Prototype and feature selection by sampling and random mutation hill climbing
algorithms," In Proc. of Eleventh International Machine Learning, pp.293-301, 1994.
[21] Adrian Perrig, Robert Szewczyk, J. D. Tygar, Victor Wen, and David E. Culler, (2002) "SPINS:
Security protocols for sensor networks," Wireless Networks, Vol.8, No.5, pp.521-534.
[22] Lee, S.hyun. & Kim Mi Na, (2008) “This is my paper”, ABC Transactions on ECE, Vol. 10, No. 5,
pp120-122.
[23] Gizem, Aksahya & Ayese, Ozcan (2009) Coomunications & Networks, Network Books, ABC
Publishers.
Authors
Jae Kwon Lee received his B.S. degree in Computer Software Engineering from the
Kumoh National Institute of Technology, Republic of Korea, in 2012, M.S degrees in
Electrical and Computer Engineering from Sungkyunkwan University in 2014,
respectively. His research interests are in the areas of wireless sensor network,
intelligent systems, modelling & simulation, and enterprise resource planning.
Su Man Nam received his B.S. degrees in computer information from Hanseo
University, Korea, in February 2009 and M.S degrees in Electrical and Computer
Engineering from Sungkyunkwan University in 2013, respectively. He is currently a
doctoral student in the College of Information and Communication Engineering at
Sungkyunkwan University, Korea. His research interests include wireless sensor
network, security in wireless sensor networks, and modelling & simulation.
Tae Ho Cho received the Ph.D. degree in Electrical and Computer Engineering from
the University of Arizona, USA, in 1993, and the B.S. and M.S. degrees in Electrical
Engineering from Sungkyunkwan University, Republic of Korea, and the University of
Alabama, USA, respectively. He is currently a Professor in the College of Information
and Communication Engineering, Sungkyunkwan University, Korea. His research
interests are in the areas of wireless sensor network, intelligent systems, modeling &
simulation, and enterprise resource planning.

E NERGY - E FFICIENT P ATH C ONFIGURATION M ETHOD FOR DEF IN WSN S

More Related Content

What's hot (19)

Viewers also liked (16)

Similar to E NERGY - E FFICIENT P ATH C ONFIGURATION M ETHOD FOR DEF IN WSN S (20)

Recently uploaded (20)

E NERGY - E FFICIENT P ATH C ONFIGURATION M ETHOD FOR DEF IN WSN S