E010242430

IOSR Journal of Electronics and Communication Engineering (IOSR-JECE)
e-ISSN: 2278-2834,p- ISSN: 2278-8735.Volume 10, Issue 2, Ver. IV (Mar - Apr.2015), PP 24-30
www.iosrjournals.org
DOI: 10.9790/2834-10242430 www.iosrjournals.org 24 | Page
Design A Square Microstrip Patch Antenna for S-Band
Application
N.Mohamed Sabidha Banu1
, Dr.M.Ramkumar Prabhu2
& U.T.Sasikala3
PG Student1
, Professor2
,Asst.Prof3
, Department of ECE, Dhaanish Ahmed College of Engineering, Chennai.
Abstract: In recent years there is a need for more compact antennas due to rapid decrease in size of personal
communication devices. This paperdeals with the problem of size and performance of antenna. This paper
presents design and simulation of a square micro strip patch antenna at 2.6 GHz for S- Band communications
that provides a radiation pattern along a wide angle of beam and achieves a good gain. The square micro strip
patch antenna was analyzed using Ansoft/Ansys HFSS. The proposed inset feed square patch antenna provide
good Resonant Frequency, Return Loss, VSWR, Radiation Pattern and the antenna Gain.
Index Terms: Micro strip antenna, Inset feed, Return Loss
I. Introduction
Micro strip patch antennas (also just called patch antennas) are among the most common antenna types
in use today, particularly in the popular frequency range of 1 to 6 GHz. This type of antenna had its first intense
development in the 1970s, as communication systems became common at frequencies where its size and
performance were very useful. At the same time, its flat profile and reduced weight, compared to parabolic
reflectors and other antenna options, made it attractive for airborne and spacecraft applications. More recently,
those same properties, with additional size reduction using high dielectric constant materials, have made patch
antennas common in handsets, GPS receivers and other mass-produced wireless products. This tutorial article is
intended to provide basic information on patch antenna design and operation, directed to engineers who are
mainly designers of RFmicrowave circuits. The paper hope that this information will assist them as they design
circuitry connected to these antennas, or as they are called on to evaluate and specify a vendor’s antenna product
for their current project.
Antennas are indispensable elements of any wireless communication systems. There are several type of
antenna are available they are wire antenna, log periodic antenna, travelling wave antenna, micro strip antenna,
aperture antenna, reflector antenna. The wire antenna comprises of several antenna they are short dipole
antenna, dipole antenna, half wave dipole, broadband dipole, monopole antenna and loop antenna. In spite of
this antenna, in this project micro strip antenna is designed with frequency of 2.6GHZ.Micro strip antenna
comprises of 2 antennas theyare rectangular micro strip (patch) antenna and planar inverted-F antenna Micro
strip or patch antennas arebecoming increasingly useful because they can be printed directly onto a circuit
board. Micro strip antennas are becoming very widespread within the mobile phone market. Patch antennas are
low cost, have a low profile and are easily fabricated. Micro strip antennas find many applications as they are
low profile, light weight, conformable to surface and inexpensive to manufacture using printed-circuit
technology. For a patch, the length L of the element is usually the L< λg/2 (where λg is the guide wavelength
on the substrate). Thicker substrates with lower dielectric constant provide better efficiency and larger
bandwidth but at the expense of larger element size. Thin substrates with higher dielectric constants lead to
smaller element sizes, minimize coupling, but are less efficient and have relatively smaller bandwidth.
Micro strip patch antennas have enjoyed proliferated use in many circularly polarized applications due
to their low-profile and useful radiation characteristics. In the last decade, the development of modern wireless
systems has prompted increased investigation on micro strip radiators, with particular attention paid to
improving performance and miniaturization. Compared to a circular patch for a given frequency the square
geometry is smaller in size. In modern communication system requires low profile, light weight, high gain, and
simple structure antennas to give surety reliability, mobility, and high efficiency characteristics. Due to the
existence of growth in development of low cost, less weight, highly reliable, minimal profile antennas for
wireless devices, it poses a new challenge for the design of antenna in wireless communications. This paper
presents design and simulation of a square micro strip patch array antenna at 2.6 GHz for wireless
communications that provides a radiation pattern along a wide angle of beam and achieves a good gain.
The rest of the paper has been divided into Fiveparts.Section 1 describes overview of antenna. Section
2 describes an overview of the Micro strip patch antenna. Section 3describesdesign consideration of
antenna.Section 4 describes simulation results. Section 5 describesthe conclusion and future work respectively.

Design A Square Microstrip Patch Antenna for S-Band Application
II. Micro Strip Patch Antenna
As communication devices become smaller due to greater integration of electronics, the antenna
becomes a significantly larger part of the overall package volume. This results in a demand for similar
reductions in antenna size. In order to simplify analysis and performance prediction, the patch is generally
square, rectangular, circular, triangular, elliptical or some other common shape. The square micro strip patch
antenna is the widely used of all the types of micro strip antennas that are present The substrate material,
dimension of antenna, feeding technique will determines the performance of micro strip antenna. Hence among
different feeding techniques, inset fed technique is used for the design of square micro strip patch antenna at
2.6GHz.Themicro strip patch antenna is shown in fig 1.Micro strip patch antenna has a ground plane on the one
side of a dielectric substrate which other side has a radiating patch as shown below in Figure 1.
Figure 1 Micro strip antenna
A square patch is used as the main radiator. The patch is generally made of conducting material such as
copper or gold and can take any possible shape. Dielectric constant of the substrate (𝜖r) is typically in the range
2.2<𝜖r <12. For good antenna performance, a low dielectric constant with thick dielectric substrate is desirable,
as it provides better radiation, better efficiency and larger bandwidth.
A. Inset Feed Method
This typically yields high input impedance. Since the current is low at the ends of a half wave patch
and increases in magnitude toward the center, the input impedance could be reduced if the patch was fed closer
to the center. One method of doing this is by using an inset feed (a distance R from the end) as shown in the
figure 2. Since the current has a sinusoidal distributions, moving in a distance R from the end will increase the
current by cos (π*R/L) - this is just nothing that the wavelength is 2*L, and so the phase difference is 2*π*R/
(2*L) =π*R/L
Transmission line model depicts the micro strip antenna by two slots of width W and height h separated
by transmission line of length L.Themicro strip is a non-homogeneous of two dielectrics, typically, substrate and
the air. Most of the electric field lines reside some part in the air and rest in the substrate. This results that
transmission line does not support transverse electric magnetic (TEM) mode of transmission, as phase velocities
would be different in substrate and in the air.
Figure 2.Patch antenna with insert feed
B. Micro Strip Patch Antennaanalysinng Method
Assume a square micro strip antenna of width W, length L resting on the height of a substrate h. The
coordinate axis was selected as the height along z direction, length along x direction and width along y
direction. In order to operate in the fundamental mode, length of the patch should be slightly less than λ/2,
where λ is the wavelength equal to λ0 / .The TM10 implies that field varies a cycle of λ/2 along the

length, and width of the patch has no variation. The micro strip patch antenna is represented by two slots,
separated by a transmission line of length L and open circuited at both the ends as shown in Figure 3.
Figure 3 square patch antenna
The normal components of the electric field at the two edges along the width are in opposite directions
and thus out of phase as seen in Figure 4. Since the patch is λ/2 long and hence they cancel each other in the
broadside direction. The tangential components which are in phase, means that the resulting fields combine to
give maximum radiated field normal to the surface of the structure.
Figure 4. Electric field lines
III. Design Consideration Of Antenna
The paper has designed a Square patch antenna of the center frequency 2.6 GHz. Gain required as
11.5dBi. The antenna has employed a hybrid structure and using Rogers RT duroid 5880 as a substrate.
The three essential parameters for the design of micro strip patch antenna are:
1) Frequency of operation (f 0).
2) Dielectric constant of the substrate (𝜖r).
3) Height of dielectric substrate (H).
For the micro strip patch antenna the height of the dielectric substrate is critical since the antenna
should not be bulky. The resonant frequency of the antenna must be selected appropriately. The transmission
line model will be used to design the antenna. The edge type feed is used in this design.
C. Antenna Design Calculations
1) Frings factor:
2) Calculation of length:
Where,
3) For a Micro strip patch antenna, the resonance Frequency is given as
Where m and n are modes along L and W respectively.
4) Calculation of width:
For efficient radiation, the width W is given as

5) Calculation of height of dielectric substrate (H):
The equation to determine the height of the dielectric substrate is
6) Calculation of the ground plane dimensions ( Lg and Wg ):
The transmission line model is applicable to infinite ground planes only. However, for practical
considerations, it is essential to have a finite ground plane. It has been similar results for finite and infinite
ground plane can be obtained if the size of the ground plane is greater than the patch dimensions by
approximately six times the substrate thickness all around the periphery. Hence, for this design, the ground
plane dimensions would be given as:
Lg = 6h+L
Wg = 6h+W
Hence after calculating all the parameters using the above formulae, the micro strip patch antenna was designed.
7) Determination of feed point location:
The feed co-ordinates were calculated Yf = W/2 and Xf = X0-ΔL where,
and
8) Dielectric Substrate
It was found suitable to select a thin dielectric substrate with low dielectric constant by considering the
trade-off between the antenna dimensions and its performance. Thin substrate permits to reduce the size and also
spurious radiation as surface wave, and low dielectric constant for higher bandwidth, better efficiency and low
power loss. The simulated results were found satisfactory.
IV. Simulation Results And Discussion
The three essential parameters for the design of a Square Micro strip Patch Antenna:
1. Frequency of operation (fo): The resonant frequency of the antenna must be selected appropriately. The
resonant frequency selected for the design is 2.6 GHz.
2. Dielectric constant of the substrate (εr): The dielectric material selected for our design is Rogers RT duroid
5880 which has a dielectric constant of 2.2.A substrate with a high dielectric constant has been selected
since it reduces the dimensions of the antenna.
3. Height of dielectric substrate (h):
For the micro strip patch antenna substrate is selected as 1.6 mm.
Table 1 Dimensions of patch antenna
Solution Frequency 2.6 GHz
Patch Dimension 41.2 mm
Substrate dimension along x 100 mm
Substrate dimension along y 90 mm
Inset feed width 1.8 mm
Inset feed length 20 mm
Table 1.Shows the parameter selected for design a square micro strip antenna. Inset feed value is noted
and the different calculation noted for test purpose.

D. Structure Of Patch Antenna Design
Figure 5. Feed micro strip antenna
Figure 5.Shows the square patch array antenna design is shown in below figure in 3D model. It consists
of patch elements on one side of a dielectric substrate and a planar ground on the other side. It was assigned
with an air box boundary and virtual radiation to create far field radiation pattern and assigned with a excitation.
Figure 6. Full view of square patch micro strip antenna
Figure 6 shows the full view of antenna, here the ground is taken as a rectangular and the medium for
the ground is E- plan. A rectangular box is covers the antenna.
The square patch micro strip antenna is simulated using Ansoft HFSS. The parameters evaluated were
gain, beam width and return loss. Table 2 shows the comparison of proposed system with different frequency
range. Here the Proposed system gave a good gain and result is satisfactory.
Table 2. Comparison of measured gain, return loss and bandwidth at two frequencies for single patch antenna.
Frequency in GHz Substrate Gain Return Loss
2.25
Rogers RT
RT duroid 5880
8 dB -42dB
2.4
Rogers RT
RT duroid 5880
9 dB -14dB
2.6
Rogers RT
RT duroid 5880
11.5 dB -32.11dB
E. Radiation Pattern Plots
Since a micro strip patch antenna radiates normal to its patch surface, the elevation pattern for φ = 0
and φ = 90 degrees would be important.

Figure 7.below shows the gain of the antenna at 2.6 GHz for φ = 0 and φ = 90 degrees and shows the
radiation pattern of proposed system. The maximum gain is obtained in the broadside direction and this is
measured to be 1.87 dBi for both, φ = 0 and φ = 90 degrees.
Figure 7. Radiation pattern of proposed system
F. Return Loss
The inset feed used is designed to have an inset depth of 20 mm, feed-line width of 1.8 mm and feed
path length of 20 mm. A frequency range of 2.6 GHz is selected and 20 frequency points are selected over this
range to obtain accurate results. The center frequency is selected as the one at which the return loss is minimum.
The bandwidth can be calculated from the return loss (RL) plot. The bandwidth of the antenna can be said to be
those range of frequencies over which the RL is greater than -9.5 dB (-9.5 dB corresponds to a VSWR of 2
which is an acceptable figure). Using PSO, the optimum feed depth is found to be at Yo = 13.2mm where a RL
of -32 dB is obtained. The plot for frequency v/s return loss is shown in Figure 8.
Figure 8. S-parameter plot for frequency v/s Return loss of proposed system
V. Conclusion
The design of square micro strip patch antenna with operating frequency 2.6 GHz suitable for s band
application using inset feed feeding technique has been completed using HFSS software. The performance
parameters were achieved with gain 11.5 dB and beam width 40 degrees in E-plane and 26 degrees in H-plane
for patch antenna. The proposed antenna consists of a single patch for single operating frequency. In future two
patches are going to be stacked and slots will be introduced to operate in two operating frequency to achieve
high gain and good return loss.
References
[1]. B. Eissfeller, G. Ameres, V. Kropp, and D. Sanroma, Performance of GPS, GLONASS and Galileo 2007.
[2]. G. Ramesh, P. Bhartia, I. Bahl, and A. Ittipiboon, Micro strip Antenna Design Handbook. London, U.K.: Artech House, 2001, pp.
493–526.
[3]. Y. Lin, H. Chen, S. Member, and S. Lin, “A new coupling mechanism for circularly polarized annular-ring patch antenna,” IEEE
Trans. Antennas Propag., vol. 56, no. 1, pp. 11–16, Jan. 2008.
[4]. Z. Yijun, C. Chen, and J. L. Volakis, “Proximity-coupled stacked patch antenna for tri-band GPS applications,” in Proc. IEEE
Antennas Propag. Soc. Int. Symp., Albuquerque, NM, 2006, pp. 2683–2686.

[5]. B. R. Rao, M. A. Smolinski, C. C. Quach, and E. N. Rosario, “Triple band GPS trap loaded inverted L antenna array,” Microw.
Opt. Technol. Lett., vol. 38, no. 1, pp. 35–37, 2003.
[6]. Y. Lee, S. Ganguly, and R.Mittra, “Tri-band (L1, L2, L5) GPS antenna with reduced backlobes,” presented at the 28th General
Assembly Int. Union Radio Sci., URSI-GA, New Delhi, India, 2005.
[7]. C. F. Tseng, S. C. Lu, and Y. C. Hsu, “Design of micro strip antenna with modified annular-ring slot for GPS application,” in Proc.
PIERS,Suzhou, China, Sep. 2011, pp. 242–245.
[8]. R. B.Waterhouse, “Stacked patches using high and low dielectric constant material combinations,” IEEE Trans. Antennas Propag.,
vol. 47,no. 12, pp. 1767–1771, Dec. 1999.
[9]. H. C. Lien and H. C. Tsai, “A wide-band circular polarization stacked patch antenna for the wireless communication Applications,”
PIERS, vol. 4, no. 2, pp. 255–258, 2008.
[10]. K. Yegin, D. G. Morris, N. F. Bally, R. J. Snoeyink, and W. R.Livengood, “Patch Antenna with Parasitically Enhanced Perimeter,”
US Patent Application 2005/0280592 A1, Dec. 22, 2005.
[11]. D. Pozar and S. M. Duffy, “A Dual-Band Circularly Polarized Aperture-Coupled Stacked Micro strip Antenna for Global
Positioning Satellite,”IEEE Trans. on Antennas and Propagation, Vol. 45, No. 11, pp. 1618-1625, Nov. 1997.
[12]. R. B. Waterhouse, “Broadband stacked shorted patch,” Electronics Letters, Vol. 35, No. 2, pp. 98-100, Jan. 1999.
[13]. K. Yegin, D. G. Morris, N. F. Bally, R. J. Snoeyink, and W. R Livengood, “Integrated GPS and SDARS Antenna,” US Patent
Application 2006/0097924 A1, May 11, 2006.
[14]. R. Garg, P. Bhartia, I. Bahl, and A. Ittipiboon, Micro strip Antenna Design Handbook, Artech House, 2000.
[15]. K. F. Lee, Ed., Advances in Micro strip and Printed Antennas, John Wiley, 1997.
[16]. D. M. Pozar and D. H. Schaubert, Micro strip Antennas: The Analysis and Design of Micro strip Antennas and Arrays, IEEE Press,
1995.
[17]. F. E. Gardiol, “Broadband Patch Antennas,” Artech House.
[18]. S K Behera, “Novel Tuned Rectangular Patch Antenna As a Load for Phase Power Combining” Ph.D Thesis, Jadavpur University,
Kolkata.
[19]. D. R. Jackson and J. T. Williams, “A comparison of CAD models for radiation from rectangular micro strip patches,” Intl. Journal
of Microwave and Millimeter-Wave Computer Aided Design,Vol.1,No. 2, pp. 236-248, April 1991.
[20]. D. R. Jackson, S. A. Long, J. T. Williams, and V. B. Davis, “Computer- aided design of rectangular micro strip antennas”, ch. 5 of
Advances in Micro strip and Printed Antennas, K. F.Lee, Editor, John Wiley, 1997.
[21]. D. M. Pozar, “A reciprocity method of analysis for printed slot and slot- coupled micro strip antennas,” IEEE Trans. Antennas and
Propagation, vol. AP-34, pp. 1439-1446, Dec. 1986.
[22]. C. A. Balanis, “Antenna Theory, Analysis and Design,” John Wiley &Sons, New York,1997.
[23]. H. Pues and A Van de Capelle, “Accurate transmission-line model for the rectangular micro strip antenna,” Proc. IEE, vol. 131, pt.
H, no. 6, pp. 334-340, Dec. 1984.

E010242430

More Related Content

What's hot (18)

Viewers also liked (20)

Similar to E010242430 (20)

More from IOSR Journals (20)

Recently uploaded (20)

E010242430