Feature satip3
0 likes247 views
This document discusses the basics of transmitting data over a network for IPTV, including protocols like TCP, UDP, RTP, and multicasting versus unicasting. It explains that TCP ensures correct delivery but is not ideal for live video, while UDP is better suited due to its simplicity and lack of error checking. RTP improves on UDP for streaming media. Multicasting sends a stream to multiple receivers without using additional bandwidth, while unicasting sends to one receiver. It recommends a 1000Mbps network for optimal IPTV performance and monitoring network traffic with Wireshark.
Feature satip3
- 1. ■ 148 149TELE-audiovision International — The World‘s Largest Digital TV Trade Magazine — 09-10/2013 — www.TELE-audiovision.com www.TELE-audiovision.com — 09-10/2013 — TELE-audiovision International — 全球发行量最大的数字电视杂志 La TV desde la Red Parte 3 • Los principios básicos de la transmisión de datos en una red • TCP, UDP y RTP - ¿Que significan? • Utilizando una red • El cableado de red hace que todos los otros cables sean redundantes • Se recomiendan cableados de 1000MBPS para una operación adecuada This is how our test centre looked like for this report. FEATURE IPTV hecha por uno mismo
- 2. 1 2 3 4 150 TELE-audiovision International — The World‘s Largest Digital TV Trade Magazine — 09-10/2013 — www.TELE-audiovision.com FEATURE Selfmade IPTV 1. Schematics of a MULTICAST transmission. The server sends one stream to the switch. The transmission is then forwarded to all connected devices. 2. Schematics of a UNICAST transmission. The server sends one stream to the switch, but this time the stream is only forwarded to one specific client. Notice how the remaining ports are fully available for other communications. 3. Analogy of UDP: one transmitter sends information, regardless of how many listeners there are. Also, there is no feedback to the transmitter. If a listener misses a part or if he cannot correctly receive the transmission, there is nothing to do about it – the transmitter will never know! 4. Analogy of TCP: one transmitter sends information to one listener. The reception of every sentence has to be confirmed by the listener. If he missed the sentence or if he did not understand it clearly, the transmitter will send the sentence again. Vitor Martins Augusto You can find quite a bit of infor- mation on IPTV in the Internet but it’s often not all that easy to understand since it can be very long-winded and complicated and assumes the reader has some ba- sic knowledge. One reason for the difficulty in getting started in this field is that most of the material doesn’t have TV installers in mind but rather is more geared towards network specialists and IT admin- istrators; two worlds bump into each other here. Our goal is to save our TELE-audiovision readers some time and describe the more impor- tant points. Taking the leap into the IPTV world is made complicated by these keywords: TCP, UDP, RTP, Multicasting and Uni- casting. But none of these are really earth-shattering. Almost everyone today that uses a computer or tablet to get to the Inter- net knows what TCP is. This network protocol regulates the communication between the various computers. Data is sent in small packets from the send- er’s computer to the recipient’s com- puter. To prevent the loss of a packet, it contains the address of the transmit- ter and the receiver. The packet also includes a checksum that is calculated from the data it contains. This makes it possible to determine if the packet ar- rives correctly and undamaged. The best thing about TCP is that the individual packets are transmitted until a confirmation is sent back by the re- ceiver. If this is the case, the transmit- ter can then forget about the correctly received data. Otherwise, the packet would be retransmitted as often as needed until a reception confirmation is sent back. The order in which the indi- vidual data packets are received is not important – they will be placed in the proper order by the receiver. You can look at TCP as an amateur ra- dio communication between two Hams: the first Ham transmits a lengthy mes- sage and after each sentence waits for the second Ham to signal that he re- ceived the message by saying „Roger“. If he didn‘t understand it the first time, the first Ham repeats the transmission. This protocol is ideal for data trans- missions; it guarantees that the data arrives correctly and in one piece. For live video and/or audio transmissions this protocol is not as ideally suited. There are two problems: 1) The video (or audio) has to arrive in the correct order. What good would it do if the third frame, for example, is lost and after the seventh frame the whole thing is repeated? 2) The checksum process is redun- dant. If the image data of a frame doesn‘t arrive correctly, it would be too late the retransmit that frame.
- 3. 1 2 3 4 152 TELE-audiovision International — The World‘s Largest Digital TV Trade Magazine — 09-10/2013 — www.TELE-audiovision.com Because of these reasons the UDP protocol is much better suited for live trans- missions of audio and vid- eo. In this case we‘re deal- ing with a greatly simplified protocol in that the data packets are sent without a checksum. Aside from that, the transmitter is not looking for any kind of return signal from the receiver. And in Multicast mode the transmit- ter really doesn‘t care who‘s on the receiving end. Analog to UDP could be compared to a radio broad- cast: the DJ reads the news aloud and has no idea who‘s listening, no idea how good the reception is and no idea if the listener understood everything that was said. Unlike TCP, with UDP you 1. DekTec DTE-3137 in action. Amazing how much performance has been fitted in such a small device – yet, it can inject a complete DVB-S/S2 transponder into the network. 2. In order to be able to work with IPTV, we had to get ourselves a gigabit switch. These are very cheap now, so there is no excuse to keep struggling with 100MBPS technology. 3. The Dexing NDS3975 in action: it is receiving three transponders (one from its internal tuner, one from the Topreal TP-1011 through ASI and one from the DekTec DTE-3137 through IP). It then multiplexes a new transponder which is output through ASI and IP (on a different IP). Amazing! 4. This picture shows one clear advantage of using only IPTV within a studio or head-end station: notice the blue network cable – this single cable is enough to transport all required information. Actually, all other cables could be removed (except for the LNB-cable, in case you want to use the internal tuner).
- 4. 1 2 3 154 TELE-audiovision International — The World‘s Largest Digital TV Trade Magazine — 09-10/2013 — www.TELE-audiovision.com should make sure there is a reliable network connec- tion between the transmitter and receiver, otherwise the broadcast won‘t be reliable. RTP on the other hand is not a fundamental protocol like TCP or UDP. On the con- trary, RTP is a protocol layer based on UDP. This means that as a basis UDP is always used for RTP. RTP offers a number of functions that greatly improve live audio and video transmissions: • Data identification • Time stamps for audio/ video synchronization • Maintaining the order of MPEG frames • Special handling of MPEG key frames This just goes to show that RTP should be used when- ever all the devices involved support this protocol. With Multicasting an au- dio/video stream is simply transmitted without any par- ticular receiver in mind. This transmission is routed to all users by the network and it‘s up to the users to de- cide if they want to receive it or not. Obviously this is extremely practical if more than one user wants to re- ceive the same stream. As many users as desired can tune in without the need for additional network band- width between the transmit- ter and the switch. Since the switch has to process numerous data packets, it could very quickly become overloaded when dealing with a cheap SOHO product (Small Office, Home Office) while at the same time additional data is ex- changed between users. If, for example, User 2 doesn‘t want to take part in Multi- casting and would rather send a large file to User 3, it could happen that the flow of this data transmission is re- duced to a snail‘s pace or it might not function at all. To utilize Multicasting, with regard to the IP destination address it would be good enough to configure using any IP address from 224.0.0.0 to 239.255.255.255. This ad- dress range would be used by all of the Multicast de- 1. Wireshark capturing the network traffic. Beware that lots of data is captured during a IPTV broadcast. You should only capture data for some seconds, otherwise it will take ages to process all captured packets. 2. After capturing the network traffic for a short period, there are many analysis tools available within Wireshark. This picture shows where the traffic originated. It can be clearly seen that the devices with IP-address 192.168.1.149 and 192.168.1.210 generated a huge amount of traffic. Notice the destination IP: they are multicasting IPs 3. All captured packets can be analyzed individually and the contents can be viewed, while the header is shown in a more detailed way.
- 5. 4 5 6 7 156 TELE-audiovision International — The World‘s Largest Digital TV Trade Magazine — 09-10/2013 — www.TELE-audiovision.com 4. This graph shows the bandwidth during the captured transmission. Inter- estingly, the bandwidth is not constant, when displayed in millisecond interval. 5. This graph shows the bandwidth of the same transmission, but as Bits/ second. With just two transponders fed into the network, a 100MBPS switch is working at its limit. In fact, we tried to use a 100MBPS switch and it froze after a few seconds. A regular operation was only possible using a 1000MBPS switch. 6. Using DekTec’s StreamXpert soft- ware, which already has been tested in TELE-satellite 11-12/2012, together with the professional DekTec DTE-3137 receiver, one has much more feed- back about the IPTV broadcast. Notice the lower left corner: a graph shows continuously the occupied network bandwidth. 7. StreamXpert can show all possi- ble information about the streamed transponder, including the programme clock reference (PCR), required for correct synchronization of audio and video. This allows editing the times- tamps in order to compensate for any detected errors. vices. Note that Multicast is not only used for IPTV; it is used whenever the same data needs to be sent to multiple com- puters, such as, when multiple computers need to be installed all at the same time via a network. That‘s how IT professionals, for ex- ample, in universities or large company‘s install an operating system on hundreds of computers all at once. With Unicasting how- ever, the stream - un- like Multicasting - is sent to one specific re- ceiver. This has the ad- vantage of not loading down the network for all the remaining users allowing data traffic to function normally. The data is routed in the switch between the in- puts of the servers and the users while the re- maining switch ports remain free. The disadvantage is the fact that for eve- ry additional user the stream would have to be individually retrans- mitted. In no time at all the network bandwidth
- 6. 8 9 10 11 158 TELE-audiovision International — The World‘s Largest Digital TV Trade Magazine — 09-10/2013 — www.TELE-audiovision.com 8. Despite having a perfect picture, StreamXpert indicates some errors in PAT and PMT. Interestingly; these were already present in the original DVB-S stream… 9. Useful information provided by StreamXpert: the grid view, where all active services within the stream are mapped according to their PID. 10. Meanwhile, we monitor our Dexing NDS3975 with the SnmpNMS management software. This application gives us remote access to the internals of this integrated professional receiver. 11. On the Mux-tab, we can specify which channels of the three different incoming transponders (through the internal tuner, ASI-in and IPTV) we want to output. ate via a 100MBPS interface; in view of the fact that the bandwidth of common DVB- S/S2 transponders transport data on average at 50MBPS, this would be sufficient. All the IPTV receivers we know of also operate on a 100MBPS network interface. Why then would you want to upgrade to a 1000MBPS in- frastructure? The simplest explanation is this: if cars could only drive at 55 MPH, then in principle single-lane roads would be good enough. But if there are a large num- ber of cars all on the road at the same time, then a multi- lane highway would be much better even though the cars would be moving no faster than 55 MPH. A 100MBPS switch is designed for this speed and would fall to its knees if all the ports would suddenly demand high data transfer rates at the same time. A 1000MBPS switch is would reach its capacity and it‘s especially the connection from the server to the switch that would need to withstand enormous amounts of data. The question often arises if IPTV should be operated at 100MBPS or would it be better at 1000MBPS (also referred to as 1GBPS or 1GBit/s). It‘s not an easy answer; it depends ulti- mately on how you want to use IPTV and the network. When different receivers will only route single transpond- ers to one or more multiplex- ers, then for the most part a 100MBPS network would suffice. Quite often profes- sional receivers only oper-
- 7. 13 12 160 TELE-audiovision International — The World‘s Largest Digital TV Trade Magazine — 09-10/2013 — www.TELE-audiovision.com simply able to handle much more data internally. If you want to provide IPTV to a community, a ho- tel or a home where the network would be used for other services (Internet, File sharing, VoIP, etc.), then we definitely would recom- mend a 1000MBPS network. In today‘s day and age this is considered standard and upgrading from a 100MBPS network to a 1000MBPS network should not really present any problems if the cables already in place are CAT-5e or CAT-6 types. If this isn‘t the case, the exist- ing cable should be replaced with CAT-6 cable. The switches would also have to be updated and you should make sure that the network adapter on older computers can also handle 1000MBPS. To get an overview of the network, it would pay to in- stall a Network Monitoring Program, also called a Net- work Sniffer. These pro- grams log all packets that are sent on a network. In order for this to be tech- nically possible, special soft- ware, known as WinPcap, needs to be installed. Win- Pcap places the computer‘s network card in „promiscu- ous“ mode in which the net- work card accepts all pack- ets, not just those that are specifically meant for that computer, but all of them. Additionally, WinPcap pro- vides an interface for ap- plications to gain access to these data packets. The most well-known and most popular network monitoring program is Wire- shark. The basic require- ment is WinPcap and with that all of the data traffic can be logged. In this way it‘s easy to recognize which IP addresses from which com- puters are requesting which data packets. It‘s also easy to identify if network multi- casting is in use, how much bandwidth is being used, etc. And the good news? Both WinPcap and Wireshark are free. Whether in a studio or in a headend, IPTV has estab- lished itself as an omnipres- ent solution for the distri- bution of audio and video signals. There are many advantages regardless if IPTV is used for the internal distribution in a headend or for the direct feed to an end user. Just the fact alone that all data can be sent over a sin- gle cable makes it worth uti- lizing this technology. 12. To check our IPTV streams within the network, we use VLC. 13. TSReader Professional is an excellent tool when it comes to analyze transponder streams. Instead of just rendering the channel, TSReader shows all PIDs and their respective bandwidth.