Frequently Asked Questions on TURBINE Part 3

Frequently Asked Questions
TURBINE PART 3
Questions 86 to 180
Manohar Tatwawadi
total output power solutions, Pune
Mob. No. +91 9372167165
https://manohar61.blogspot.com/2022/01/faq-on-
steam-turbines.html

86. Is there any other type of racking occurring in HP/IP rotors and causing rotor
failures?
• Blade-groove-wall cracking.
• Rotor-surface cracking.
87. Of all the factors that contribute to the unreliability of steam turbines, which one
is the most prominent?
• It is the problem of turbine blade failures that chiefly contribute to the unreliability
of steam turbines.
88. Rim cracking continues to be a problem of shrunk-on-disc type rotors in utility
steam turbines. Where does it occur?
• Cracking has been located at the outer corners of tile grooves where the blade root
attaches to the rotor.
89. So can you recommend this technique as a permanent measure?
• No, this can be recommended in extreme cases or at best temporarily.
90. So what should be the more sound approach?
• The more reasonable and better approach is to replace the damaged blades with
new ones that are stiffened by: • Serrating the interface surface of individual
blades so they interlock, or • Welding the blades together. • In some cases, a single
monolithic block is machined out to manufacture the blades in a group. • In some
other cases, blades themselves are directly welded into the rotor.
18-01-2022 total output power solutions 2

91. Steam blowing from a turbine gland is wasteful. Why else should it be avoided?
• It should be avoided because the steam usually blows into the bearing, destroying the lube
oil in the main bearing. Steam blowing from a turbine gland also creates condensate,
causing undue moisture in plant equipment.
92. The consequences of turbine depositions have three effects?
• Economic Effect: 1. Reduction in turbine output 2. Decrease in efficiency requiring higher
steam consumption.
• Effect of Overloading and Decreasing Reliability in Operation: 1. Pressure characteristic in
the turbine gets disturbed with the effect that thrust and overloading of thrust bearing
increase. 2. Blades are subjected to higher bending stresses. 3. Natural vibrations of the
blading are affected. 4. Vibration due to uneven deposition on turbine blading. 5. Valve
jamming due to deposits on valve stems.
• Corrosion Effect: Fatigue corrosion, Pitting corrosion, Stress corrosion.
93. Usually it has been found that SCC attack takes place particularly at keyways of shrunk-on-
disc rotors of low-pressure turbines. Why are keyways prone to SCC attack? s: • Keyways
shrunk-fit each disc onto tile rotor shaft. They improve the rigidity of the connection
between the disc and the central shaft However, key ways are subjected to abnormal
centrifugal forces due to high overspeed, that reduce the amount of shrink. Tangential
stresses tend to gravitate at the keyway connection and steam tends to condense. • It is a
one-piece-construction, and thus has inherent rigidity. • Advanced steel making techniques
enable building of monobloc rotors almost free from non-metallic inclusions and gas
bubbles. Even large monobloc rotors of clean steel are being manufactured today. • It
exhibits lower inherent stresses. • The chance of disc loosening during operation is
eliminated. • Highly stressed keyway is eliminated.

94. What are four types of turbine seals? :
• Carbon rings fitted in segments around the shaft and held together by garter or retainer
springs.
• Labyrinths mated with shaft serrations or shaft seal strips.
• Water seals where a shaft runner acts as a pump to create a ring of water around the
shaft. Use only treated water to avoid shaft pitting.
• Stuffing box using woven or soft packing rings that are compressed with a gland to
prevent leakage along the shaft.
95. What are some common troubles in surface-condenser operation? :
• The greatest headache to the operator is loss of vacuum caused by air leaking into the
surface condenser through the joints or packing glands.
• Another trouble spot is cooling water leaking into the steam space through the ends of
the tubes or through tiny holes in the tubes. The tubes may also become plugged with
mud, shells, debris, slime, or algae, thus cutting down on the cooling-water supply, or
the tubes may get coated with lube oil from the reciprocating machinery.
• Corrosion and dezincification of the tube metal are common surface-condenser
troubles.
• Corrosion may be uniform, or it may occur in small holes or pits. Dezincification changes
the nature of the metal and causes it to become brittle and weak.

96. What are the advantages of steam turbines over reciprocating steam engines?
• The advantages of steam turbines are: 1. Steam turbine has higher thermal
efficiency than reciprocating steam engines. 2. The brake horsepower of steam
turbines can range from a few HP to several hundred thousand HP in single units.
Hence they are quite suitable for large thermal power stations. 3. Unlike
reciprocating engines, the turbines do not need any flywheel, as the power
delivered by the turbine is uniform. 4. Steam turbines are perfectly balanced and
hence present minimum vibrational problem. 5. High rpm l8000 - 24000 can be
developed in steam turbines but such a high speed generation is not possible in the
case of reciprocating steam engines. 6. Some amount of input energy of steam is
lost as the reciprocating motion of the piston is converted to circular motion. 7.
Unlike reciprocating steam engines, no internal lubrication is required for steam
turbines due to the absence of rubbing parts. 8. Steam turbines, if well designed
and properly maintained, are more reliable and durable prime movers than steam
engines.
• 97. What are the advantages of velocity compounding? Answers: • The velocity
compounding system is easy to operate and operation is more reliable. • Only two
or three stages are required. Therefore, first cost is less. • Since the total pressure
drop takes place only in nozzles and not in the blades, the turbine casing need not
be heavily built. Hence the economy in material and money. • Less floor space is
required.

98. What are the advantages of welded rotors? Answers: • Welded rotor is a composed
body built up by welding the individual segments. So the limitations on forgings
capacity do not apply. • Welding discs together results in a lower stress level. Therefore,
more ductile materials can be chosen to resist SCC attack. • There are no keyways. So
regions of high stress concentrations are eliminated.
99. What are the basic causes of the problem of rotor failure? Answers: • Normal wear. •
Fatigue failure due to high stress. • Design deficiency. • Aggressive operating
environment.
100. What are the causes of radial axial-bore cracks on HP/IP rotors/shafts? Answers: • The
predominant cause is creep, which may act with or without low cycle fatigue. • Also the
cracks result due to poor creep ductility due to faulty heat treatment process.
101. What are the differences between impulse and reaction turbines? Answers: • The
impulse turbine is characterized by the fact that it requires nozzles and that the
pressure drop of steam takes place in the nozzles. • The reaction turbine, unlike the
impulse turbines has no nozzles, as such. It consists of a row of blades mounted on a
drum. The drum blades are separated by rows of fixed blades mounted in the turbine
casing. These fixed blades serve as nozzles as well as the means of correcting the
direction of steam onto the moving blades. • In the case of reaction turbines, the
pressure drop of steam takes place over the blades. This pressure drop produces a
reaction and hence cause the motion of the rotor.

102. What are the disadvantages of velocity compounding? Answers: • Steam velocity is
too high and that is responsible for appreciable friction losses. • Blade efficiency
decreases with the increase of the number of stages. • With the increase of the
number of rows, the power developed in successive rows of blade decreases. For as
much as, the same space and material are required for each stage, it means,
therefore, that all stages are not economically efficient.
103. What are the factors that contribute to bearing failure in a steam turbine?
• Improper lubrication. (Only the recommended lubricant should be used. )
• Inadequate water-cooling. a. The jacket temperature should be maintained in the
range of 37-60°C. b. The flow of cooling water should be adjusted accordingly.
• Misalignment. It is desirable that ball bearings should fit on the turbine shaft with a
light press fit. If the fitting is too tight, it will cause cramping. On the other hand, if
the fitting is too loose it will cause the inner race to turn on the shaft. Both
conditions are undesirable. They result in wear, excessive vibration and overheating.
And bearing failure becomes the ultimate result.
• Bearing fit.
• Excessive thrust.
• Unbalance.
• Rusting of bearing.

104. What are the losses in steam turbines? Answers: • Residual Velocity Loss - This is
equal to the absolute velocity of the steam at the blade exit. • Loss due to Friction
- Friction loss occurs in the nozzles, turbine blades and between the steam and
rotating discs. This loss is about 10%. • Leakage Loss. • Loss due to Mechanical
Friction - Accounts for the loss due to friction between the shaft and bearing. •
Radiation Loss - Though this loss is negligible, as turbine casings are insulated, it
occurs due to heat leakage from turbine to ambient air which is at a much lower
temperature than the turbine. • Loss due to Moisture - In the lower stages of the
turbine, the steam may become wet as the velocity of water particles is lower
than that of steam. So a part of the kinetic energy of steam is lost to drag the
water particles along with it.
105. What are the main causes of turbine vibration? Answer: 1. unbalanced parts 2.
poor alignment of parts 3. loose parts 4. rubbing parts 5. lubrication troubles
6. steam troubles 7. foundation troubles 8. cracked or excessively worn parts.
106. What are the points of SCC attack? Answers: SCC attack predominates where
corrodents deposit and build up. i.e. in those blading areas where flowing steam
cannot provide a washing effect.
• What are these points in particular? a. Tie wires. b. Tie wire holes. c. Brazings. d.
Blade covers. e. Tenon holes. At what points does corrosion fatigue does show up?
It attacks trailing edges, near the base of the foil and also the blade-root
serration’s.

107. What are the possible causes for the turbine not running at rated speed? Answers:
The possible causes are: a. too many hand valves closed, b. oil relay governor set too
low, c. inlet steam pressure too low or exhaust pressure too high, d. load higher than
turbine rating, e. throttle valve not opening fully, f. safety trip valve not opening
properly, g. nozzles plugged, h. steam strainer choked.
108. What are the possible causes of a governor not operating? Answers: • Restriction of
throttle valve reflex.. • Failure of governor control on start-up. If it is found that after
start-up, the speed increases continuously and the governor is not closing the throttle
valve, it may be that the governor pump has been installed in the wrong direction.
109. What are the possible causes of excessive vibration or noise in a steam turbine?
Answers: Misalignment, Worn bearings, Worn coupling to driven machine, unbalanced
coupling to driven machine, unbalanced wheel, piping strain, Bent shaft.
110. What are the possible causes of the speed of the turbine rotor increasing excessively
as the load is decreased? Answers: Throttle valve not closing fully & Wearing of
throttle valve seats.
111. What are the stresses to which a steam turbine rotor is subjected during its service
life? Answers: • Mechanical stress - The factors that contribute to mechanical stress in
the shaft are the centrifugal forces and torque’s generated due to revolving motion of
the shaft as well as bending arising during steady-state operation. • Thermal stress -
Transient operating phases i.e. startup and shutdown the genesis of thermal stress
induced to the turbine shaft. • Electrically induced stress - They originate due to short
circuits and faulty synchronization.

112. What are three types of condensers? Answer: surface (shell-and-tube) , jet &
barometric.
113. What are topping and superposed turbines? Answer: Topping and superposed
turbines are high-pressure, non-condensing units that can be added to an older,
moderate-pressure plant. Topping turbines receive highpressure steam from new
high-pressure boilers. The exhaust steam of the new turbine is at the same pressure as
the old boilers and is used to supply the old turbines.
114. What are two types of clearance in a turbine? Answers: Radial (- the clearance at the
tips of the rotor and casing) & Axial (- the foreand-aft clearance, at the sides of the
rotor and the casing)
115. What design modification is adopted to reduce susceptibility of last lowpressure
stages to fatigue failure? Answer: One modification is to join the blade segments
together at the shroud band.
116. What does "upgrading" generally means in the context of steam turbines? Answer:
Upgrading is a most widely used tern. It encompasses a variety of meanings verses life
extension, modernization and up-rating of steam turbines.
117. What does the term "ramp rat" mean? Answer: Ramp rate is used in bringing a turbine
up to operating temperature and is the degrees Fahrenheit rise per hour that metal
surfaces are exposed to when bringing a machine to rated conditions. Manufactures
specify ramp rates for their machines in order to avoid thermal stresses.
Thermocouples are used in measuring metal temperatures.

118. What factors are responsible for turbine-blade failures? Answers: • In the high
pressure cylinder, the turbine blades are mostly affected by: Solid-particle erosion
(SPE) & high cycle fatigue, • Whereas in the last few stages of the low-pressure
cylinder, the blade damage is mainly afflicted by: o erosion, o corrosion, o
Stress/fatigue damage mechanism. o According to EPRI (Electric Power Research
Institute, USA) data stress corrosion cracking and fatigue are the chief exponents for
turbine-blade failures in utility industries.
119. What factors cause excessive steam leakage under carbon rings? Answers: • Dirt
under rings. - Steam borne scale or dirt foul up the rings if steam is leaking under the
carbon rings. • Shaft scored. • Worn or broken carbon rings. These should be replaced
with a new set of carbon rings. The complete ring is to be replaced.
120. What factors contribute to excessive speed variation of the turbine? Answers: •
Improper governor droop adjustment. • Improper governor lubrication. • Throttle
assembly friction. • Friction in stuffing box. • High inlet steam pressure and light load.
• Rapidly varying load.
121. What is a balance piston? Answer: Reaction turbines have axial thrust because
pressure on the entering side is greater than pressure on the leaving side of each
stage. To counteract this force, steam is admitted to a dummy (balance) piston
chamber at the low-pressure end of the rotor. Some designers also use a balance
piston on impulse turbines that have a high thrust. Instead of pistons, seal strips are
also used to duplicate a piston's counter force.

122. What is a combination thrust and radial bearing? Answer: This unit has the ends of
the babbitt bearing extended radially over the end of the shell. Collars on the rotor
face these thrust pads, and the journal is supported in the bearing between the
thrust collars.
123. What is a multiport governor valve? Why is it used? Answer: In large turbines, a valve
controls steam flow to groups of nozzles. The number of open valves controls the
number of nozzles in use according to the load. A bar-lift or cam arrangement
operated by the governor, opens and closes the valves in sequence. Such a device is a
multiport valve. Using nozzles at full steam pressure is more efficient than throttling
the steam.
124. What is a radial-flow turbine? Answer: In a radial-flow turbine, steam flows outward
from the shaft to the casing. The unit is usually a reaction unit, having both fixed and
moving blades. They are used for special jobs and are more common to European
manufacturers.
125. What is a shrunk-on-disc rotor? Answer: These are built by heat expanding the discs,
so that upon cooling they shrink on the main rotor forging.
126. What is a stage in a steam turbine? Answer: In an impulse turbine, the stage is a set
of moving blades behind the nozzle. In a reaction turbine, each row of blades is called
a "stage." A single Curtis stage may consist of two or more rows of moving blades.
127. What is a tapered-land thrust bearing? Answer: The babbitt face of a tapered-land
thrust bearing has a series of fixed pads divided by radial slots. The leading edge of
each sector is tapered, allowing an oil wedge to build up and carry the thrust
between the collar and pad.

128. What is an air ejector? Answer: An air ejector is a steam siphon that removes non-
condensable gases from the condenser.
129. What is an extraction turbine? Answer: In an extraction turbine, steam is withdrawn from
one or more stages, at one or more pressures, for heating, plant process, or feedwater
heater needs. They are often called "bleeder turbines."
130. What is combined-cycle cogeneration? Answer: A combined cycle using a gas turbine or
diesel, usually driving a generator in which the exhaust gases are directed to a waste
heat-recovery boiler or heat-recovery steam generator (HRSG). The steam from the HRSG
is then directed to a steam turbogenerator for additional electric power production. The
use of the exhaust heat from a gas turbine improves the overall thermal efficiency. In
cogeneration, electric power is produced, but part of the steam from the HRSG or from
extraction from the steam turbine is used for process heat, hence the term cogeneration-
the simultaneous production of electric power and process heat steam.
131. What is done when cracks due to SCC or corrosion-fatigue are found? Answer: The
damaged blade is usually replaced, as repairing is difficult.
132. What is gland-sealing steam? Answer: Low-pressure steam is led to a sealing gland. The
steam seals the gland, which may be a carbon ring or of the labyrinth type, against air at
the vacuum end of the shaft.
133. What is important to remember about radial bearings? Answer: A turbine rotor is
supported by two radial bearings, one on each end of the steam cylinder. These bearings
must be accurately aligned to maintain the close clearances between the shaft and the
shaft seals, and between the rotor and the casing. lf excessive bearing wear lowers the
rotor, great harm can be done to the turbine.

134. What is meant by critical speed? Answer: It is the speed at, which the machine vibrates
most violently. It is due to many causes, such as imbalance or harmonic vibrations set up
by the entire machine. To minimize damage, the turbine should be hurried through the
known critical speed as rapidly as possible. Caution: Be sure the vibration is caused by
critical speed and not by some other trouble.
135. What is meant by the water rate of a turbine? Answer: It is the amount of water (steam)
used by the turbine in pounds per horsepower per hour or kilowatts per hour.
136. What is the cause of axial-bore cracks? Answer: Inadequate toughness of rotor steel and
transient thermal stresses.
137. What is the cause of circumferential cracking? Answer: High cycle fatigue with or without
corrosion.
138. What is the cause of turbine deposits? Answers: The turbine deposits are steam-born
foreign matters settled on turbine blades. Substances dissolved in the BFW transfer partly
from the water to steam, during the process of evaporation. They get dissolved in the
steam and are carried into the steam turbine.
139. What is the definition of a steam turbine? Answers: A steam turbine is a prime mover that
derives its energy of rotation due to conversion of the heat energy of steam into kinetic
energy as it expands through a series of nozzles mounted on the casing or produced by the
fixed blades. • Neilson defines it: The turbine is a machine in which a rotary motion is
obtained by the gradual change of the momentum of the fluid. • Graham's definition: The
turbine is a prime mover in which a rotary motion is obtained by the centrifugal force
brought into action by changing the direction of a jet of a fluid (steam) escaping from the
nozzle at high velocity.

140. What is the difference between partial and full arc admission? Answer: In multi-valve
turbine inlets, partial arc admission allows the steam to enter per valve opening in a
sequential manner, so as load is increased, more valves open to admit steam. This
can cause uneven heating on the high-pressure annulus as the valves are individually
opened with load increase. In full-arc admission, all regulating valves open but only
at a percentage of their full opening. With load increase, they all open more fully.
This provides more uniform heating around the high-pressure part of the turbine.
Most modern controls start with full-arc and switch to partial arc to reduce throttling
losses through the valves.
141. What is the essential distinguishing feature between a steam turbine and
reciprocating steam engine? Answers: • In a steam turbine, the heat energy of steam
is converted into kinetic energy by allowing it to expand through a series of nozzles
and this kinetic energy of steam is then imparted to the turbine blades mounted on
a shaft free to rotate to drive this prime mover. • In a reciprocating steam engine,
the pressure energy of steam is directly utilized to overcome the external resistance.
Here, the utilization of the KE of input steam is negligibly small.
142. What is the function of a gland drain? Answer: The function of a gland drain is to
draw off water from sealing-gland cavities created by the condensation of the
sealing steam. Drains are led to either the condenser air-ejector tube nest or the
feed water heaters. Often, gland drains are led to a lowpressure stage of the turbine
to extract more work from the gland-sealing steam.
143. What is the function of a thrust bearing? Answer: Thrust bearings keep the rotor in
its correct axial position.

144. What is the harm if the rotor is oversped? Answer: Overspeed rotor grows radially
causing heavy rub in the casing and the seal system. As a result, considerable amount
of shroud-band and tenon-rivet head damage occurs.
145. What is the nature of circumferential cracking in shrunk-on-disc rotors in steam
turbines? Answer: Regions of high stress concentration give birth to this type of
cracking. It begins in corrosion pits and propagates towards the bore by high-cycle
fatigue. It may culminate in a catastrophe, if it penetrates the bore (happily this
usually does not occur).
146. What is the nature of rotor surface cracks in steam turbines? Answer: They are
shallow in depth and have been located in heat grooves and other small radii at
labyrinth-seal areas along the rotor.
147. What is the operating principle of a reaction turbine? Answer: A reaction turbine
utilizes a jet of steam that flows from a nozzle on the rotor. Actually, the steam is
directed into the moving blades by fixed blades designed to expand the steam. The
result is a small increase in velocity over that of the moving blades. These blades form
a wall of moving nozzles that further expand the steam. The steam flow is partially
reversed by the moving blades, producing a reaction on the blades. Since the
pressure drop is small across each row of nozzles (blades), the speed is comparatively
low. Therefore, more rows of moving blades are needed than in an impulse turbine.
148. What is the possible cause of slow start up of a steam turbine? Answer: This may be
due to high starting torque required by the driven equipment.

149. What is the potential problem of shrunk-on-disc type rotor? Answers: • It is the
failure due to circumferential cracks, which are not limited to old rotors of early
models (1960), but they also take place on present-day rotors. • As a result corrodent
impurities like chlorides concentrate at key ways. This factor coupled with high stress
concentration lead to SCC attack on keyway areas.
150. What is the principle of a steam turbine? Answers: • If high-velocity steam is allowed
to blow on to a curved blade, the steam will suffer a change in direction as it passes
across the blade, and leaves it as shown. • As a result of its change in direction across
the blade, the steam will impart a force to the blade. This force will act in the
direction shown. • Now if the blade were free in the direction of force as depicted. if,
therefore, a number of blades were fixed on the circumference of a disc which is free
to rotate on a shaft, then steam blown across the blades in the way described, would
cause the disc to rotate. This is the working principle of a steam turbine.
151. What is the purpose of a turning gear? Answer: Heat must be prevented from
warping the rotors of large turbines or hightemperature turbines of 400°C or more.
When the turbine is being shut down, a motordriven turning gear is engaged to the
turbine to rotate the spindle and allow uniform cooling.
152. What is the remedy for a bent steam turbine shaft causing excessive vibration?
Answers: • The run-out of the shaft near the center as well as the shaft extension
should be checked. • If the run-out is excessive, the shaft is to be replaced.
153. What is the remedy for rotor-surface cracking? Answer: Current rotor/shaft should be
machined off (skin-peeling).

154. What is the remedy of the damage to blade profiles? Answers: • Upgrading the turbine and
depending on the extent of damage, upgrading may involve: o weld repair of affected zones
of the blade, o replacement of damaged blades by new ones and of new design, o
replacement of base material, o application of protective coatings to guard against
corrosion and erosion damage. What are the remedies to this failure? For existing rotor,
weld repair may be a choice; otherwise retire it. For new rotors, materials with improved
pitting resistance should be used.
155. What is the safe maximum tripping speed of a turbine operating at 2500 rpm? Answer: The
rule is to trip at 10 percent overspeed. Therefore, 2500 x 1.10 = 2750 rpm.
156. What is the solution to the problem of SCC/corrosion fatigue of steam turbine blades?
Answer: It involves changing the blade material as well as minimizing the presence of
corrodents in steam to a permissible level.
157. What is to be done for erosion-induced damage on high-and low-pressure stage blading?
Answers: • In such cases welding repair can be a good solution and this can be carried out
during a normal maintenance outage without removing the blade. Using oxyacetylene
torch, Stellite is generally deposited onto the damaged site. Following this, the weld is
subjected to stress-relieving and re-profiling. • In case of erosion penetrating the erosion
shield and extending to the base material, a filler material of consistent or identical
composition of blade material is used. • In some cases use is made of Inconel alloy to build
up the metal base. Therefore, using welding or brazing technique, a new shield can be
attached to the blade. If brazing technique is followed, the rebuilt section is stress-relieved
prior to the attachment of shield to it. If, on the other hand, the shield is attached by
welding, then they are stress-relieved together.

158. What is to be done in case of cracks originating at the lacing-wire holes? Answers:
These are to be weld-repaired. However the following factors must be considered: •
The length of the crack that appears on the pressure and/or suction face. • Whether
the cracks propagate towards inlet end, discharge end and or both.
159. What maybe the possible causes for the safety trip to trip at normal speed? Answers:
Excessive vibration, Leakage in the pilot valve, Deposition of dirt in the safety trip
valve.
160. What maybe the possible causes for the safety trip tripping during load variation?
Answers: Light load and high inlet steam pressure. Safety trip set very close to the
operating speed of turbine.
161. What other parts of the steam turbine blades suffer from damage? Answers: Blade
roots & Shroud band.
162. What provisions in the layout of a combined-cycle should be considered? Answer: It
is important to consider the use of a bypass stack that will permit operating the gas
turbo-generator in case of a forced outage on the HRSG or steam turbo-generator.
However, in certain states, such as California, also to be considered are NO limits
that require steam injection and loading to limit the exhaust temperature coming
out of the simple-cycle gas turbine so that they do not exceed jurisdictional limits.
163. What remedial measures you can suggest to cope with radial axial-bore cracks?
Answer: For new rotors, modified heat treatment process is recommended while for
existing rotors de-rating the turbine or replacement of the rotor may be a solution.

164. What should be done if excessive vibration is due to an unbalanced turbine wheel?
Answers: • The turbine wheel is to be checked if it became unbalanced due to
overspeeding. • The turbine wheel must be re-balanced or replaced. What should be
the remedial action? For new rotors, control cleanliness of the steel.i.e. inclusion and
segregates free and more homogeneous steel shaft is required. For current rotors,
replace the rotor, grind and overbore.
165. What should be the remedial actions for blade-groove-wall cracking? Answers: •
Modified heat treatment of new rotors is a sound and lasting remedy. • For current
rotors, cracks should be machined off and lighter blades should be installed. Better,
retire the cracked shaft.
166. What should you do if you lost vacuum while operating a condensing turbine plant?
Answer: If vacuum is lost shut down immediately. The condenser cannot stand steam
pressure; the condenser tubes may leak from excessive temperature. Excessive
pressure will also damage the shell, the exhaust, and the low-pressure parts of the
turbine.
167. What steps are taken to minimize damage from moisture on steam turbine blades?
Answers: The following measures are employed at the design stage: • Stellite inserts. •
Hardening of the base metal. • Moisture-removal devices to combat impingement
corrosion due to moisture.

168. What steps/modifications should be implemented to curtail the damage from
moisture impingement on steam turbine blades? Answers: • The drainage system
should be redesigned. Larger drains are to be provided. • More effective water-
catchers are to be in-stalled. • Radial seals are to be eliminated to remove water
before it can chance upon the blades. • Nozzle trailing edges are to be thinned to
promote the formation of smaller and less harmful droplets.
169. What types of deposits are formed on steam turbine blading? Answers: Water-
soluble deposits (NaCl, Na2SO4, NaOH and Na3PO4 ) & Waterinsoluble deposits(SiO2
(mainly)).
170. What types of cracking occur in the LP rotor shaft? Answers: Radial axial-bore cracks
& Circumferential cracks.
171. When "stall flutter" occurs? Answers: This problem is encountered when operating
limits are exceeded i.e., when turbine exhaust pressure exceeds the value what the
manufacturer has recommended. Stall flutter induces stress in the blades
172. When does SPE damage usually occur on steam turbine blades? Answer: It occurs
usually during startup or abrupt load change.
173. When does upgrading mean modernization of utility industry? Answer: Upgrading is
really modernization to all those units other than those facing uncertain load growth
and low-capital utility system. It involves replacement of damaged parts/components
by state-of-the-art components without scrapping the entire machine.
174. Where are velocity compounded steam turbines mostly employed? Answers: They
are chiefly used as the prime mover for: Centrifugal pumps, Centrifugal compressors,
Low capacity turbo-generators, Feed pumps of high capacity power plants.

175. Where do water-soluble deposits prevail? Answer: In the high-and intermediate-pressure
sections of steam turbines.
176. Where is pitting corrosion mostly prevalent? Answer: Upstream of LP stages as well as wet
stages of LP cylinder.
177. Where would you look for a fault if the air ejector did not raise enough vacuum? Answer: In
this case, the trouble is usually in the nozzle. You will probably find that: • the nozzle is
eroded • the strainer protecting the nozzle is clogged • the steam pressure to the nozzle is
too low
178. Which factors affect the extent of an upgrading program? Answers: Age of the unit & How it
has been operated. Note: Turbines less than quarter of a century old can simply be
upgraded to their original design conditions.
179. Why are free-standing blades in the last low-pressure stage favored more, in some cases,
than those that are coupled and shrouded together? Answers: • These free-standing blades
are known to provide good and adequate protection against stresses and aggressive
environment. • They eliminate all areas viz. shroud/tenon interface and tie-wire/hole area
where corrodents can collect.
180. Why are simple impulse turbines not so common? Answers: • Since the whole pressure
drop from boiler to condenser pressure takes place in a single row of nozzles, the velocity of
the steam entering the turbine is very high. If some of this velocity is used up in a single row
of turbine blading, as in the de Laval turbine, the speed of the rotation of the wheel will be
too high to be blades are be useful for practical purposes, as there is the danger of
structural failures due to excessive centrifugal stresses. • Steam exits from the turbine with
a sufficiently high velocity, meaning a considerable loss of kinetic energy.

Frequently Asked Questions on TURBINE Part 3

More Related Content

What's hot (20)

Similar to Frequently Asked Questions on TURBINE Part 3 (20)

More from Manohar Tatwawadi (20)

Recently uploaded (20)

Frequently Asked Questions on TURBINE Part 3