Garden Environmental Monitoring & Automatic Control System Using Sensors

141 International Journal for Modern Trends in Science and Technology
Volume: 2 | Issue: 05 | May 2016 | ISSN: 2455-3778IJMTST
Garden Environmental Monitoring &
Automatic Control System Using Sensors
Ashok.R1
| Mrs S K Uma2
1Department of Computer Science Engineering, PES College of Engineering, Mandya, India.
2Associate Professor, Dept.of Computer Science Engineering, PES College of Engineering, Mandya,India.
Many people have gardens in their homes. But due to their busy schedule they don’t have time to take care of
the garden. The automated garden control system achieves monitoring and control of a garden environment
by using sensors and the controller of a microcontroller running a computer program. The WSN is the recent
emerging technology in the various filed. So that by using the WSN concept we can make this paper more
reliable. The various sensors senses the garden environmental factors , microcontroller process those data
and by using ZBee protocol the data can be transmit to remote locations and demodulated by the another
Zbee, which then passes the information to the serial port. The approach of creating a GUI requires no coding
by the user and the information is still presented in a visually appealing format. The aim of our paper is to
minimize this manual intervention by the workers. Automated garden system will serve the following
purposes: 1) As there is no un-planned usage of water, a lot of water is saved from being wasted. 2) The
irrigation is the only when there is not enough moisture in the soil and the sensors decides when the motor
should be turned on/off, saves a lot time for the works. This also gives much needed rest to the workers, as
they don’t have to go and turn the motor on/off manually.
KEYWORDS: WSN, Sensors, Zigbee, Microcontroller
Copyright © 2015 International Journal for Modern Trends in Science and Technology
All rights reserved.
I. INTRODUCTION
Gardens are common in most of the houses in
India. In urban cities people grow plants in pots on
their balconies. Maintenance of these gardens is
done in an unscientific method.
Many a times the potted plants in our homes are
watered in an untimely manner. Sometimes we
tend to water the plants more than they require.
Too little water as well as too much water is
harmful for the plants. If the water provided is less,
plants are unable to develop and become
susceptible to damage from pests. On the other
hand if watered too much, the plants are prone to
get rots and other diseases. Plants require specific
amount of sunlight, water and temperature to
grow.
By controlling these factors using an automated
gardening system, plants can be grown in a better
and faster way. Automating the garden would
reduce time and energy of the user in maintaining
the garden. The Project presented here waters your
plants regularly when you are out for vocation. The
system uses low cost efficient soil moisture,
humidity and temperature sensors to decide when
and how much water will be provided to the potted
plants. The soil moisture sensors to sense the
whether the Soil is wet or dry. The comparator
monitors the sensors and when sensors sense the
dry condition then the switch on the motor for
water supply. And it will switch off the motor when
the sensors senses wet condition of soil. The
temperature sensor gives the temperature of the
surrounding in which the potted plants are placed.
The humidity sensor used for sensing the
humidity. Relative humidity is a measure in
percentage of the vapour in the air compared to the
total amount of vapour that could be held in the air
at a given temperature. The comparator does the
above job it receives the signals from the sensors.
The WSN technology is used in this paper. And
zigbee is used to send the data wirelessly from one
location to another or to base station. The sensor
readings that are obtained by the microcontroller
ABSTRACT

Garden Environmental Monitoring & Automatic Control System Using Sensors
are displayed the user to monitor the system. There
is also an LCD screen in the system to display the
data.
II. SYSTEM ANALYSIS AND REQUIREMENTS
A. System Design
The automated garden control system, whose
block diagram is depicted in figure 1, is made up of
two principal units: Sensors location and Remote
Monitoring location. These two units consist of
sensors for soil moisture, temperature, humidity,
ARM7 microcontroller board, ZigBee MODEMs,
ZigBee adapter board; and a personal computer
(PC). The sensors location is the heart of the system
that is responsible for regulating the garden
environment. The sensors acquire the
environmental data. After the data have been
filtered to remove noise they are made available to
the ARM7 board which then computes the current
values of the controlled variables and compares
them with the set thresholds. If any of the
controlled variables is outside a safe limit the
corresponding actuator is activated to restore the
optimum condition. The ARM7 board also reads
the states of the actuators and transmits the
information along with the current values of the
controlled variables to the remote monitoring
location via ZBee radio frequency (RF) MODEM pair
that operate at a frequency of 2.4 GHz. A large
number of wireless linking devices exist, however
ZBee has been used for this work primarily
because of its suitability for low power data
transmission.
Fig 1: Block Diagram
B. Soil Moisture Sensor
In this paper, a capacitive soil moisture sensor
has been developed based on Frequency Division
Reflectometry (FDR). The concept of FDR is
explained as follows:
• The electrical capacitance of a capacitor that uses
the soil as a dielectric depends on the soil water
content.
• When connecting this capacitor (made of metal
plates or rods imbedded in the soil) together with
an oscillator to form an electrical circuit, changes
in soil moisture can be detected by changes in the
circuit operating frequency.
• This is the basis of the Frequency Domain (FD)
technique used in Capacitance and Frequency
Domain Reflectometry (FDR) sensors.
• In Capacitance sensors the dielectric permittivity
of a medium is determined by measuring the
charge time of a capacitor made with that medium.
• In FDR the oscillator frequency is swept under
control within a certain frequency range to find the
resonant frequency (at which the amplitude is
greatest), which is a measure of water content in
the soil.
C. Temperature Sensor
A simple temperature sensor using one LM35
precision Integrated-circuit temperature device
with an output voltage linearly-proportional to the
centigrade temperature. It can measure
temperature from -55c to +150c. The voltage
output of the LM35 increases 10mV per degree
Celsius rise in temperature. LM35 can be operated
from a 5V supply and stand by current is less than
60μA.The purpose of this sensor in this system is
to monitor the temperature and to regulate Air
Cooler system .It is designed that whenever the
temperature goes beyond 35˚ C the Air Cooler
system has to turn on. Temperature sensor LM35
is interfaced to the microcontroller. The conversion
of Celsius and Fahrenheit is done by certain
formula. The output is displayed in the serial
monitor. When the temperature goes above 35C the
cooler system gets ON automatically.
D. IR Counter Measurement
An infrared sensor is an electronic instrument
which is used here to detect and count the motion
of cones on conveyer. IR sensors are capable of
detecting motion of object and heat emitted by an
object. IR detectors are specially filtered for
Infrared light; they are not good at detecting visible
light. On the other hand, photocells are good at

Volume: 2 | Issue: 05 | May 2016 | ISSN: 2455-3778IJMTST
detecting yellow/green visible light, not well at IR
light.
E. Humidity Sensor
The humidity sensor SYS-1used for sensing the
humidity. It delivers instrumentation quality RH
(Relative Humidity) sensing performance in a low
cost, solder able SIP (Single In-line Package).
Relative humidity is a measure, in percentage, of
the vapour in the air compared to the total amount
of vapor that could be held in the air at a given
temperature.
III. FLOW DIAGRAM
The main dataflow diagram of the automated garden control
system is shown in figure 2.
Figure 2.overall dataflow for the Automated garden Control
System
IV. RESULTS
The proposed system is successfully
implemented and desired outputs are obtained.
When the power supply is given through a dc
battery, the process starts and the sensors start
sensing the corresponding parameters and are
displayed on the LCD. And simultaneously the
results are stored in PC The authorized person has
access the data from any place at any time and can
monitor the parameters successfully.
The figure 3 shows the overall project module
and the desired outputs are successfully obtained.
The figures 4 and 5 show the variation in
temperature, soil moisture and humidity with the
time and are captured using MATLAB simulator.
The figure 6 shows the data sheet of
temperature, soil moisture and humidity for each
arying time 2-3 seconds and is monitored
continuously using WSN.
Fig 3.Project module
Fig 4. Main page of GUI
Fig 5 variation in temperature, soil moisture and
humidity with the time and are captured using
MATLAB simulator

Garden Environmental Monitoring & Automatic Control System Using Sensors
Fig 6. Values stored in database.
V. CONCLUSION
A step-by-step approach in designing the
microcontroller based system for measurement
and control of the four essential parameters for
Garden growth, i.e. temperature, humidity, soil
moisture, and IR Sensor, has been followed. The
results obtained from the measurement have
shown that the system performance is quite
reliable and accurate.
The system has successfully overcome quite a
few shortcomings of the existing systems by
reducing the power consumption, maintenance
and complexity, at the same time providing a
flexible and precise form of maintaining the
environment.
REFERENCES
[1] XU Lei, ZHANG Hong-wei, LI Xiao-hui, WU
Xian-Liang, A Design of Wireless Temperature and
Humidity Monitoring System, ICCET 2010.
[2] MahirDursun, SemihOzden, A wireless application
of drip irrigation automation supported by soil
moisture sensors, Scientific Research and Essays
Vol. 6(7), pp. 1573-1582, 4 April, 2011.
[3] Okunola. A. I. 2013. Glasshouse Production of
Vegetable and Ornamentals for Agricultural
Production in Nigeria. World Science Research
Journals.
[4] Mancuso, M. and Bustaffa, F. 2006. A Wireless
Sensor Network for Monitoring Environmental
Variables in a Tomato Greenhouse. Proceedings of
International Workshop on Factory Communication
Systems, Torino, Italy, IEExplore, 107-110.
[5] Hobby Electronics. 2014. Humidity Sensor –
HIH4030 Breakout. Accessed from:
http://www.hobbytronics.co.uk/humidity-sensor-h
ih4030
[6] Vegetronix. 2014. VH400 Soil Moisture Sensor
Probe. Accessed from:
http://www.vegetronix.com/Products/VG400/
[7] S. B. Idso , T. J. Schmugge , R. D. Jackson and R. J.
Reginato “The utility of surface temperature
measurements for the remote sensing of surface soil
water status”, J. Geophys. Res., vol. 80, pp.3044 -
3049 1975 .
[8] A.J. Both, “ Dynamic simulation of supplemental
lighting for greenhouse hydroponic lettuce
production”, 1995 :Cornell Univ.
[9] Vu Minh Quan ; Sch. of Eng. & Adv. Technol. (SEAT),
Massey Univ., Palmerston North, New Zealand ; Sen
Gupta, G. ; Mukhopadhyay, S.,” Review of sensors
for greenhouse climate monitoring”, 2011 IEEE
,ISBN:978-1-4244-8063-0.

Garden Environmental Monitoring & Automatic Control System Using Sensors

More Related Content

What's hot (20)

Viewers also liked (19)

Similar to Garden Environmental Monitoring & Automatic Control System Using Sensors (20)

Recently uploaded (20)

Garden Environmental Monitoring & Automatic Control System Using Sensors