Gsm based campus display system project report
16 likes23,515 views
Here are the key steps in the information transfer process for this GSM-based campus display system: 1. An authorized user sends an SMS from their mobile phone to the GSM modem connected to the system. 2. The GSM modem receives the SMS via the cellular network. 3. The microcontroller connected to the GSM modem reads the incoming SMS. 4. The microcontroller validates the sender's mobile number to check if they are authorized. 5. If authorized, the microcontroller extracts the message content from the SMS. 6. The microcontroller then encodes/converts the message into a format suitable for display on the LCD. 7. The microcontroller interfaces with
Gsm based campus display system project report
- 1. “ GSM BASED CAMP D PUS DIS SPLAY SYSTEM ” (USIN MIC NG CROCON NTROL LLER A AT89S52 2) A PROJE ECT REPO ORT Subm mitted by YAP SHA (09030 KASHY AH 00111022 2) PRAGNE HAR (090 ESH SUTH 03001110 086) YUVRA RATHO (090300111114 AJ OD 4) In partia fulfilmen of the re al nt equiremen for the award of t nts the deggree of BACHE ELOR O ENGIN OF NEERING In ELECTR RONICS & COMMU UNICATI ION L.D.R.P Institute o Techno of ology & Re esearch, G Gandhinag gar Guja arat Tech hnologica Univers al sity, Ahm medabad Decem mber, 2012
- 2. Acknowledgement We place on record and warmly acknowledge the continuous encouragement, invaluable supervision, timely suggestions and inspired guidance offered by our guide Prof. Dilip H. Patel, professor, Department of Electronics & Communication engineering, at LDRP Institute of Technology & Research, Gandhinagar, in bringing this report to a successful completion. We are grateful to Prof. S.E.Mendhe, Head of the Department of Electronics & Communication engineering for permitting us to make use of the facilities available in the department to carry out the project successfully. Last but not the least we express our sincere thanks to all of our friends and our parents who have patiently extended all sorts of help for accomplishing this undertaking. Shah Kashyap B. (090300111022) Suthar Pragnesh G. (090300111086) Rathod Yuvraj S. (090300111114)
- 3. Abstract In the last couple of decades, communication technology has developed by leaps and bounds. It has already established its importance in sharing the information right from household matters to worldwide phenomena. Apart from sharing information, it is also used for remote control of machines and electronic appliances. In our day-to-day life, we use many such appliances at home, office and public places for our comfort and convenience. Every device requires one or the other kind of operation control for which it has a HMI (human-machine interface). Communication technology not only helps us to exchange information with human beings but also allows us to carry out monitoring and controlling of machines from remote locations. This remote control of appliances is possible with wired or wireless communication interfaces embedded in the machines. The use of “Embedded System in Communication” has given rise to many interesting applications. One of such applications is public addressing system (PAS). Many companies are manufacturing audio / video systems like public announcement system, CCTV, programmable sign boards etc. But all these systems are generally hard-wired, complex in nature and difficult to expand. So, by adding wireless communication interface such as GSM to these systems, we can overcome their limitations.
- 4. L.D.R.P Institute of Technology & Research, Gandhinagar Electronics & Communication Engineering Department 2012 CERTIFICATE Date: This is to certify that the dissertation entitled “ GSM BASED CAMPUS DISPLAY SYSTEM ” has been carried out by SHAH KASHYAP B., SUTHAR PRAGNESH G., RATHOD YUVRAJ S. under my guidance in fulfilment of the degree of Bachelor of Engineering in Electronics & Communication (7th Semester/8th Semester) of Gujarat Technological University, Ahmedabad during the academic year 2012-13. Guides: Head of the Department: Prof. Dilip H. Patel Prof. S.E. Mendhe (Internal)
- 5. Table Of Contents Acknowledgement ii Abstract iii Certificate iv Table of Content v List of Figures vii List of Tables viii Chapter : 1 Introduction 1 1.1 Project Overview 2 1.2 Information transfer 2 1.3 Components Overview 3 Chapter : 2 Design Overview 5 2.1 Design on paper 6 2.2 Schematic Interfacing 7 Chapter : 3 Hardware Profile 8 3.1 GSM Modem 9 3.1.1 Accesing GSM Modem 10 3.1.2 Testing of GSM Modem 11 3.1.3 List of Important AT Commands 15 3.2 LCD Display 21 3.2.1 Important Signals 22 3.2.1.1 Enable (EN) 23 3.2.1.2 Register Select (RS) 23 3.2.1.3 Read/Write (R/W) 23
- 6. 3.3 Microcontroller AT89S52 26 3.3.1 Features 26 3.3.2 Description 27 Chapter : 4 Interfacing 28 4.1 Microcontroller-Modem Interfacing 29 4.1.1 DTE and DCE 29 4.1.2 RS-232 29 4.1.2.1 RS-232 Signals 31 4.2 Microcontroller-LCD Interfacing 32 Chapter : 5 Software Solvency 34 5.1 End User Perspective 35 5.2 Control Flow 36 5.2.1 Initialization 36 5.2.2 Serial Transfer using TI and RI flags 36 5.2.3 Validity check & Display 36 Chapter : 6 Implementation at the institute level 37 6.1 Overview 38 6.2 Proposal 38 Chapter : 7 Conclusion 39 7.1 Conclusion & Future Improvements 40 References : 42
- 7. List of Figures Figure 2.1 Design Overview Figure 2.2 Schematic Diagram Figure 3.1 Matrix Simado GD-T11 GSM Modules Figure 3.2 MS HyperTerminal's Connection Description dialog box Figure 3.3 HyperTerminal's Properties dialog box Figure 3.4 MS HyperTerminal's Connect to dialog box Figure 3.5 MS HyperTerminal's main window Figure 3.6 AT89S52 Microcontroller Figure 4.1 Female 9 Pin Plug Figure 4.2 Pin Configuration Of LCD Interface Figure 5.1 Flowchart
- 8. List of Tables Table 3.1 Pin Configuration of LCD Table 3.1 Control Codes of LCD Table 4.1 RS-232 Signals
- 10. 1.1 Project Overview The Campus Display System (CDS) is aimed at the colleges and universities for displaying day-to-day information continuously or at regular intervals during the working hours. Being GSM-based system, it offers flexibility to display flash news or announcements faster than the programmable system. GSM-based campus display system can also be used at other public places like schools, hospitals, railway stations, gardens etc. without affecting the surrounding environment. The CDS mainly consists of a GSM receiver and a display toolkit which can be programmed from an authorized mobile phone. It receives the SMS, validates the sending Mobile Identification Number (MIN) and displays the desired information after necessary code conversion. It can serve as an electronic notice board and display the important notices instantaneously thus avoiding the latency. Being wireless, the GSM based CDS is easy to expand and allows the user to add more display units at anytime and at any location in the campus depending on the requirement of the institute. 1.2 Information Transfer 1.1.2 Information Transfer A coordinated sequence of user and telecommunications system actions that causes information present at a source user to become present at a destination user. An information-transfer transaction usually consists of three consecutive phases called the access phase, the information-transfer phase, and the disengagement phase. 1.2 Broadcast A term to describe communication where a piece of information is sent or transmitted from one point to all other points. There is just one sender, but the information is simultaneously sent to all connected receivers.
- 11. In networking, a distinction is made between broadcasting and multicasting. Broadcasting sends a message to everyone on the network whereas multicasting sends a message to a select list of recipients. One of the most common examples is broadcast through a cellular network service. This serves multiple end users at different locations in a simulcast fashion. Practically every cellular system has some kind of broadcast mechanism. This can be used directly for distributing information to multiple mobiles, commonly, for example in a mobile telephony system, the most important use of broadcast information is to set up channels for one to one communication between the mobile Trans-receiver and the base station. This is called paging. The details of the process of paging vary somewhat from network to network, but normally we know a limited number of cells where the phone is located (this group of cells is called a location area in the GSM system). Paging takes place by sending the broadcast message on all of those cells. This project aims at integrating the expansiveness of a wireless cellular network and the ease of information transfer through the SMS with the coverage of campus display boards. It can also be a modest effort to realize the complete potential of public display boards in instantaneous information broadcast in swift response to events of interests. 1.3 Components Overview This system uses the following components. Microcontroller CDS is based on AT89S52 microcontroller which is a variant of 8052. It is an 8-bit microcontroller with 8KB on-chip Flash memory, 256 bytes RAM, three timer / counters, one serial and four 8-bit parallel ports. It can also address up to 64KB of external data memory RAM and program memory. LCD The GSM based CDS uses HD44780 LCD for displaying the text data. It is 20 character x 2 line display module. But in practice, it should be replaced by the large multiline, multi- colour commercial display units
- 12. GSM Modem A GSM modem is a wireless modem that works with a GSM wireless network. A wireless modem behaves like a dial-up modem. The main difference between them is that a dial-up modem sends and receives data through a fixed telephone line while a wireless modem sends and receives data through radio waves. Like a GSM mobile phone, a GSM modem requires a SIM card in order to operate. In this project, we must take into account the fact that the modem requires a wired connection at one end and wireless at the other. Matrix Simado GDT11 is a Fixed Cellular Terminal (FCT) for data applications. It is a compact and portable terminal that can satisfy various data communication needs over GSM. It can be connected to a computer with the help of a standard RS232C serial port. Simado GDT11 offers features like Short Message Services (SMS), Data Services (sending and receiving data files), Fax Services and Web Browsing. The Simado GDT11 is easy to set up. Computers use AT commands to control modems. Both GSM modems and dial-up modems support a common set of standard AT commands. GSM modem can be used just like a dial- up modem. In addition to the standard AT commands, GSM modems support an extended set of AT commands. These extended AT commands are defined in the GSM. Computer Interface Finally, this project uses RS232 serial interface for interfacing the GSM modem with a PC. This interface is used to setup the GSM modem. A hyper terminal application is used to issue AT commands to the GSM modem. MAX-232 The MAX232 is a dual driver/receiver that includes a capacitive voltage generator to supply EIA-232 voltage levels from a single 5-V supply. Each receiver converts EIA-232 inputs to 5-V TTL/CMOS levels. These receivers have a typical threshold of 1.3 V and a typical hysteresis of 0.5 V, and can accept ±30-V inputs.
- 14. 2.1. Design on Paper As explained in the introduction chapter, the realization of complete potential of the display boards and the wireless medium in information transfer is the major issue that the following thesis of the following project deals with. Figure 2.1 Design Overview As we see in the above figure, there are at least three interfacing circuits, MAX-232 with Microcontroller, LCD display with microcontroller, and MAX-232 with GSM MODEM. It is not a hidden fact that interfacing a MODEM with a normal PC is quite easy with the help of the AT commands sent to it from the Hyper Terminal window. But we must take into account the fact that the MODEM requires a wired connection at one end and wireless at the other. Dedicating a general purpose computer at each and every site of the display boards, although makes the task a lot easier but is too expensive to be a possibility. Hence we employ Atmel 89S52 microcontroller with 64 Kb EEROM storage memory.
- 15. The complexity of coding substantially increases, but once programmed the module works at its robust best since it is a dedicated embedded system and not a general purpose computer. The design procedure involves identifying and assembling all the required hardware and ensuring fail safe interfacing between all the components. Then we have the coding process which has to take care of the delays between two successive transmissions and most importantly the validation of the sender’s number. The number of valid mobile numbers can be more than one. The limiting constraint is the RAM of the microcontroller rather than the coding-complexities. Figure 2.2 Schematic diagram
- 17. 3.1. GSM MODEM A GSM modem is a wireless modem that works with a GSM wireless network. A wireless modem behaves like a dial-up modem. The main difference between them is that a dial-up modem sends and receives data through a fixed telephone line while a wireless modem sends and receives data through radio waves. Like a GSM mobile phone, a GSM modem requires a SIM card from a wireless carrier in order to operate. Matrix Simado GDT11 is a Fixed Cellular Terminal (FCT) for data applications. It is a compact and portable terminal that can satisfy various data communication needs over GSM. It can be connected to a computer with the help of a standard RS232C serial port. Simado GDT11 offers features like Short Message Services (SMS), Data Services(sending and receiving data files), Fax Services and Web Browsing. Remote login and data file transfer are also supported. It is the perfect equipment for factory plants, resorts,dams and construction sites where wired connectivity is not available or not practicable. The Simado GDT11 is easy to set up. It finds its applications in IT companies, Banks and Financial Institutions, Logistic Companies, Service Providers, Remote Project Sites, Professionals, and such other business establishments. Computers use AT commands to control modems. Both GSM modems and dial-up modems support a common set of standard AT commands. GSM modem can be used just like a dial- up modem. In addition to the standard AT commands, GSM modems support an extended set of AT commands. These extended AT commands are defined in the GSM standards. With the extended AT commands, various things can be done: Reading, writing and deleting SMS messages. Sending SMS messages. Monitoring the signal strength. Monitoring the charging status and charge level of the battery. Reading, writing and searching phone book entries.
- 18. Fig. 3.1: Matrix Simado GD-T11 GSM module 3.1.1 Accessing GSM MODEM using Microsoft HyperTerminal Microsoft HyperTerminal is a small program that comes with Microsoft Windows. We use it to send AT commands to the GSM modem. It can be found at Start -> Programs -> Accessories -> Communications -> HyperTerminal. Before programming our SMS application, it is required to check if the GSM modem and SIM card are working properly first. The MS HyperTerminal is a handy tool when it comes to testing the GSM device. It is a good idea to test the GSM devices beforehand. When a problem occurs, sometimes it is difficult to tell what causes the problem. The cause can be the program, the GSM device or the SIM card. If GSM device and SIM card with MS HyperTerminal and they operate properly, then it is very likely that the problem is caused by the program or other hard wares. For Linux users, Mincom can be used instead of HyperTerminal.
- 19. 3.1.2 Testing of GSM MODEM To use MS HyperTerminal to send AT commands to the GSM modem, the following procedure is followed. 1. We put a valid SIM card into the GSM modem. We can obtain a SIM card by subscribing to the GSM service of a wireless network operator. 2. Since in our case the modem drivers were pre installed, we need not to install any such drivers. 3. Then we start up MS HyperTerminal by selecting Start -> Programs -> Accessories -> Communications -> HyperTerminal. 4. In the Connection Description dialog box (as shown in the screenshot given below), we enter any name and choose an icon we like for the connection. Then we click the OK button. Figure 3.2 : The screenshot of MS HyperTerminal's Connection Description dialog box
- 20. 5. In the Connect To dialog box, choose the COM port that your mobile phone or GSM modem is connecting to in the Connect using combo box. For example, choose COM1 if your mobile phone or GSM modem is connecting to the COM1 port. Then click the OK button.(Sometimes there will have more than one COM port in the Connect using combo box. To know which COM port is used by your mobile phone or GSM modem, follow the procedure below. In Windows 98: Go to Control Panel -> Modem. Then click the Diagnostics tab. In the list box, you can see which COM port the mobile phone or GSM modem is connected to. In Windows 2000 and Windows XP: Go to Control Panel -> Phone and Modem Options. 6. The Properties dialog box comes out. Enter the correct port settings for your mobile phone or GSM modem. Then click the OK button. (To find the correct port settings that should be used with your mobile phone or GSM modem, one way is to consult the manual of your mobile phone or GSM modem. Another way is to check the port settings used by the wireless modem driver that you installed earlier. To check the port settings used by the wireless modem driver on Windows 98, follow these steps: a. Go to Control Panel -> Modem. b. Select your mobile phone or GSM modem in the list box. c. Click the Properties button. d. The Properties dialog box appears. The Maximum speeds field on the General tab corresponds to HyperTerminal's Bits per second field. Click the Connection tab and you can find the settings for data bits, parity and stop bits. Click the Advanced button and you can find the setting for flow control.
- 21. To check the port settings used by the wireless modem driver on Windows 2000 and Windows XP, follow these steps: a. Go to Control Panel -> Phone and Modem Options -> Modems tab. b. Select your mobile phone or GSM modem in the list box. c. Click the Properties button. d. The Properties dialog box appears. Click the Advanced tab and then click the Change Default Preferences button. e. The Change Default Preferences dialog box appears. The Port speed field on the General tab corresponds to HyperTerminal's Bits per second field. You can also find the setting for flow control on the General tab. On the Advanced tab, you can find the settings for data bits, parity and stop bits.) Figure 3.3 : The screenshot of MS HyperTerminal's Properties dialog box
- 22. Figure 3.4 : The screenshot of MS HyperTerminal's Connect to dialog box 7. Type "AT" in the main window. A response "OK" should be returned from the mobile phone or GSM modem. Type "AT+CPIN?" in the main window. The AT command "AT+CPIN?" is used to query whether the mobile phone or GSM modem is waiting for a PIN (personal identification number, i.e. password). If the response is "+CPIN: READY", it means the SIM card does not require a PIN and it is ready for use. If your SIM card requires a PIN, you need to set the PIN with the AT command "AT+CPIN=<PIN>".
- 23. Figure 3.5 the screenshot of MS HyperTerminal's main window If you get the responses above, your mobile phone or GSM modem is working properly. You can start typing your own AT commands to control the mobile phone or GSM Modem. 3.1.3 List of important AT commands AT Commands : AT commands are used to control MODEMs. AT is the abbreviation for Attention. These commands come from Hayes commands that were used by the Hayes smart modems. The Hayes commands started with AT to indicate the attention from the MODEM. The dial up and wireless MODEMs (devices that involve machine to machine communication) need AT commands to interact with a computer. These include the Hayes command set as a subset, along with other extended AT commands. AT commands with a GSM/GPRS MODEM or mobile phone can be used to access following information and services:
- 24. 1. Information and configuration pertaining to mobile device or MODEM and SIM card. 2. SMS services. 3. MMS services. 4. Fax services. 5. Data and Voice link over mobile network. The Hayes subset commands are called the basic commands and the commands specific to a GSM network are called extended AT commands. Types of AT Commands: There are four types of AT commands: Explanation of commonly used AT commands: 1) AT - This command is used to check communication between the module and the computer. For example, AT OK The command returns a result code OK if the computer (serial port) and module are connected properly. If any of module or SIM is not working, it would return a result code ERROR. 2) +CMGF - This command is used to set the SMS mode. Either text or PDU mode can be selected by assigning 1 or 0 in the command.
- 25. SYNTAX: AT+CMGF=<mode> 0: for PDU mode 1: for text mode The text mode of SMS is easier to operate but it allows limited features of SMS. The PDU (protocol data unit) allows more access to SMS services but the operator requires bit level knowledge of TPDUs. The headers and body of SMS are accessed in hex format in PDU mode so it allows availing more features. For example, AT+CMGF=1 OK 3) +CMGW - This command is used to store message in the SIM. SYNTAX: AT+CMGW=” Phone number”> Message to be stored Ctrl+z As one types AT+CMGW and phone number, ‘>’ sign appears on next line where one can type the message. Multiple line messages can be typed in this case. This is why the message is terminated by providing a ‘Ctrl+z’ combination. As Ctrl+z is pressed, the following information response is displayed on the screen. +CMGW: Number on which message has been stored 4) +CMGS - This command is used to send a SMS message to a phone number. SYNTAX: AT+CMGS= serial number of message to be send. As the command AT+CMGS and serial number of message are entered, SMS is sent to the particular SIM.
- 26. For example, AT+CMGS=1 OK 5) ATD - This command is used to dial or call a number. SYNTAX: ATD<Phone number>(Enter) For example, ATD123456789 6) ATA - This command is used to answer a call. An incoming call is indicated by a message ‘RING’ which is repeated for every ring of the call. When the call ends ‘NO CARRIER’ is displayed on the screen. SYNTAX: ATA (Enter) As ATA followed by enter key is pressed, incoming call is answered. For example, RING RING ATA 7) ATH - This command is used to disconnect remote user link with the GSM module. SYNTAX: ATH (Enter) List of AT commands: The AT commands for both, GSM module and the mobile phone, are listed below. Some of these commands may not be supported by all the GSM modules available. Also there might be some commands which won’t be supported by some mobile handsets.
- 27. Testing : Command Description AT Checking communication between the module and computer. Call control : Command Description ATA Answer command ATD Dial command ATH Hang up call ATL Monitor speaker loudness ATM Monitor speaker mode ATO Go on-line ATP Set pulse dial as default ATT Set tone dial as default AT+CSTA Select type of address AT+CRC Cellular result codes Data card Control : Command Description ATI Identification ATS Select an S-register ATZ Recall stored profile AT&F Restore factory settings AT&V View active configuration AT&W Store parameters in given profile AT&Y Select Set as power up option AT+CLCK Facility lock command AT+COLP Connected line identification presentation AT+GCAP Request complete capabilities list AT+GMI Request manufacturer identification AT+GMM Request model identification AT+GMR Request revision identification AT+GSN Request product serial number identification (IMEI) Phone control : Command Description AT+CBC Battery charge AT+CGMI Request manufacturer identification AT+CGMM Request model identification AT+CGMR Request revision identification AT+CGSN Request product serial number identification AT+CMEE Report mobile equipment error AT+CPAS Phone activity status AT+CPBF Find phone book entries AT+CPBR Read phone book entry AT+CPBS Select phone book memory storage AT+CPBW Write phone book entry AT+CSCS Select TE character set AT+CSQ Signal quality
- 28. Computer data interface : Command Description ATE Command Echo ATQ Result code suppression ATV Define response format ATX Response range selection AT&C Define DCD usage AT&D Define DTR usage AT&K Select flow control AT&Q Define communications mode option AT&S Define DSR option AT+ICF DTE-DCE character framing AT+IFC DTE-DCE Local flow control AT+IPR Fixed DTE rate Service : Command Description AT+CLIP Calling line identification presentation AT+CR Service reporting control AT+DR Data compression reporting AT+ILRR DTE-DCE local rate reporting Network Communication parameter : Command Description ATB Communications standard option AT+CBST Select bearer service type AT+CEER Extended error report AT+CRLP Radio link protocol AT+DS Data compression Miscellaneous : Command Description A/ Re-execute command line AT? Command help AT*C Start SMS interpreter AT*T Enter SMS block mode protocol AT*V Activate V.25bis mode AT*NOKIATEST Test command AT+CESP Enter SMS block mode protocol SMS Text mode : Command Description AT+CSMS Select message service AT+CPMS Preferred message storage AT+CMGF Message format AT+CSCA Service centre address AT+CSMP Set text mode parameters AT+CSDH Show text mode parameters AT+CSCB Select cell broadcast message types AT+CSAS Save settings AT+CRES Restore settings AT+CNMI New message indications to TE AT+CMGL List messages AT+CMGR Read message AT+CMGS Send message AT+CMSS Send message from storage AT+CMGW Write message to memory AT+CMGD Delete message
- 29. SMS PDU mode : Command Description AT+CMGL List Messages AT+CMGR Read message AT+CMGS Send message AT+CMGW Write message to memory 3.2 LCD Display One of the most common devices attached to an 8051 is an LCD display. Some of the most common LCDs connected to the 8051 are 16x2 and 20x2 displays. This means 16 characters per line by 2 lines and 20 characters per line by 2 lines, respectively. In recent years the LCD is finding widespread use replacing LED’s. This is due to the following reasons: 1. Declining prices 2. Ability to display numbers, characters and graphics. 3. Incorporation of a refreshing controller into the LCD. 4. Ease of programming. Fortunately, a very popular standard exists which allows us to communicate with the vast majority of LCDs regardless of their manufacturer. The standard is referred to as HD44780U, which refers to the controller chip which receives data from an external source (in this case, the 8051) and communicates directly with the LCD. The 44780 standard requires 3 control lines as well as either 4 or 8 I/O lines for the data bus. The user may select whether the LCD is to operate with a 4-bit data bus or an 8-bit data bus.
- 30. If a 4-bit data bus is used the LCD will require a total of 7 data lines (3 control lines plus the 4 lines for the data bus). If an 8-bit data bus is used the LCD will require a total of 11 data lines (3 control lines plus the 8 lines for the data bus). Pin Symbol I/O Description Table 3.1 Pin Configuration of LCD 3.2.1 Important Signals
- 31. The following pins are important to LCD’s while programming 3.2.1.1 Enable (EN) The EN line is called "Enable." This control line is used to tell the LCD that you are sending it data. To send data to the LCD, your program should make sure this line is low (0) and then set the other two control lines and/or put data on the data bus. When the other lines are completely ready, bring EN high (1) and wait for the minimum amount of time required by the LCD datasheet (this varies from LCD to LCD), and end by bringing it low (0) again. 3.2.1.2 Register Select (RS) The RS line is the "Register Select" line. When RS is low (0), the data is to be treated as a command or special instruction (such as clear screen, position cursor, etc.). When RS is high (1), the data being sent is text data which should be displayed on the screen. For example, to display the letter "T" on the screen you would set RS high. 3.2.1.3 Read/Write (R/W) The RW line is the "Read/Write" control line. When RW is low (0), the information on the data bus is being written to the LCD. When RW is high (1), the program is effectively querying (or reading) the LCD. Only one instruction ("Get LCD status") is a read command. All others are write commands--so RW will almost always be low. Finally, the data bus consists of 4 or 8 lines (depending on the mode of operation selected by the user). In the case of an 8-bit data bus, the lines are referred to as DB0, DB1, DB2, DB3, DB4, DB5, DB6, and DB7. Above is the quite simple schematic. The LCD panel's Enable and Register Select is connected to the Control Port. The Control Port is an open collector / open drain output. While most Parallel Ports have internal pull-up resistors, there are a few which don't. Therefore by incorporating the two 10K external pull up resistors, the circuit is more 18 portable for a wider range of computers, some of which may have no internal pull up resistors. We make no effort to place the Data bus into reverse direction. Therefore we hard wire the R/W line of the LCD panel, into write mode. This will cause no bus conflicts on the
- 32. data lines. As a result we cannot read back the LCD's internal Busy Flag which tells us if the LCD has accepted and finished processing the last instruction. This problem is Overcome by inserting known delays into our program. The 10k Potentiometer controls the contrast of the LCD panel. Nothing fancy here. As with all the examples, I've left the power supply out. You can use a bench power supply set to 5v or use a onboard +5 regulator. Remember a few de-coupling capacitors, especially if you have trouble with the circuit working properly.
- 33. Table 3.2 Control codes of LCD
- 34. 3.3 Microcontroller AT89S52 Features: • Compatible with MCS-51® Products • 8K Bytes of In-System Programmable (ISP) Flash Memory – Endurance: 1000 Write/Erase Cycles • 4.0V to 5.5V Operating Range • Fully Static Operation: 0 Hz to 33 MHz • Three-level Program Memory Lock • 256 x 8-bit Internal RAM • 32 Programmable I/O Lines • Three 16-bit Timer/Counters • Eight Interrupt Sources • Full Duplex UART Serial Channel • Low-power Idle and Power-down Modes • Interrupt Recovery from Power-down Mode • Watchdog Timer • Dual Data Pointer • Power-off Flag Description: The AT89S52 is a low-power, high-performance CMOS 8-bit microcontroller with 8K bytes of in-system programmable Flash memory. The device is manufactured using Atmel’s high-density nonvolatile memory technology and is compatible with the industry- standard 80C51 instruction set and pinout. The on-chip Flash allows the program memory to be reprogrammed in-system or by a conventional nonvolatile memory programmer. By combining a versatile 8-bit CPU with in-system programmable Flash on a monolithic chip, the Atmel AT89S52 is a powerful microcontroller which provides a Highly-flexible and cost-effective solution to many embedded control applications.
- 35. The AT89S52 provides the following standard features: 8K bytes of Flash, 256 bytes of RAM, 32 I/O lines, Watchdog timer, two data pointers, three 16-bit timer/counters, a six-vector two-level interrupt architecture, a full duplex serial port, on-chip oscillator, and clock circuitry. In addition, the AT89S52 is designed with static logic for operation down to zero frequency and supports two software selectable power saving modes. The Idle Mode stops the CPU while allowing the RAM, timer/counters, serial port, and interrupt system to continue functioning. The Power-down mode saves the RAM contents but freezes the oscillator, disabling all other chip functions until the next interrupt or hardware reset. Figure 3.6 AT89S52 Microcontroller
- 37. 4.1 Microcontroller – MODEM Interfacing 4.1.1. DTE and DCE The terms DTE and DCE are very common in the data communications market. DTE is short for Data Terminal Equipment and DCE stands for Data Communications Equipment. But what do they really mean? As the full DTE name indicates this is a piece of device that ends a communication line, whereas the DCE provides a path for communication. Let's say we have a computer on which wants to communicate with the Internet through a modem and a dial‐up connection. To get to the Internet you tell your modem to dial the number of your provider. After your modems has dialed the number, the modem of the provider will answer your call and your will hear a lot of noise. Then it becomes quiet and you see your login prompt or your dialing program tells you the connection is established. Now you have a connection with the server from your provider and you can wander the Internet. In this example you PC is a Data Terminal (DTE). The two modems (yours and that one of your provider) are DCEs, they make the communication between you and your provider possible. But now we have to look at the server of your provider. Is that a DTE or DCE? The answer is a DTE. It ends the communication line between you and the server. When you want to go from your provided server to another place it uses another interface. So DTE and DCE are interfacing dependent. It is e.g. possible that for your connection to the server, the server is a DTE, but that that same server is a DCE for the equipment that it is attached to on the rest of the Net. 4.1.2. RS‐232 In telecommunications, RS‐232 is a standard for serial binary data signals connecting between a DTE (Data terminal equipment) and a DCE (Data Circuit‐terminating Equipment). It is commonly used in computer serial ports. In RS‐232, data is sent as a time‐series of bits. Both synchronous and asynchronous transmissions are supported by the standard. In addition to the data circuits, the standard defines a number of control
- 39. Table 4.1 RS‐232 Signals 4.1.2.1 RS‐232 Signals Transmitted Data (TxD) Data sent from DTE to DCE. Received Data (RxD) Data sent from DCE to DTE. Request To Send (RTS) Asserted (set to 0) by DTE to prepare DCE to receive data. This may require action on the part of the DCE, e.g. transmitting a carrier or reversing the direction of a half‐duplex line. Clear To Send (CTS) Asserted by DCE to acknowledge RTS and allow DTE to transmit. Data Terminal Ready (DTR) Asserted by DTE to indicate that it is ready to be connected. If the DCE is a modem, it should go "off hook" when it receives this signal. If this signal is disserted, the modem should respond by immediately hanging up. Data Set Ready (DSR) Asserted by DCE to indicate an active connection. If DCE is not a modem (e.g. a null‐modem cable or other equipment), this signal should be permanently asserted (set to 0), possibly by a jumper to another signal. Carrier Detect (CD) Asserted by DCE when a connection has been established with remote equipment. Ring Indicator (RI) Asserted by DCE when it detects a ring signal from the telephone line.
- 40. 4.2 Microcontroller‐LCD Interfacing Figure 4.2 Pin Configuration of LCD interfacing Above is the quite simple schematic. The LCD panel’s Enable and Register Select is connected to the Control Port. The Control Port is an open collector / open drain output. While most Parallel Ports have internal pull‐up resistors, there are a few which don’t. Therefore by incorporating the two 10K external pull up resistors, the circuit is more portable for a wider range of computers, some of which may have no internal pull up resistors.
- 43. 5.1 End User Perspective Figure 5.1 Flowchart The above given flowchart gives the end user perspective on the control flow. During normal operations the LCD reads a message from a fixed memory location in the microcontroller and displays it continuously, until a new message arrives for validation. It is then when a branching occurs basing on the validity of the sender’s number and further taking into account the priority assigned to the new message in comparison to the previous one.
- 44. 5.2 Control Flow 5.2.1. Initialization The baud rate of the modem was set to be 4800 bps using the command AT+IPR=4800.The ECHO from the modem was turned off using the command ATE/ATE0 at the hyper terminal. For serial transmission and reception to be possible both the DTE and DCE should have same operational baud rates. Hence to set the microcontroller at a baud rate of 4800bps, we set terminal count of Timer 1 at 0FFh (clock frequency = 1.8432). The TCON and SCON registers were set accordingly. 5.2.2. Serial transfer using TI and RI flags After setting the baud rates of the two devices both the devices are now ready to transmit and receive data in form of characters. Transmission is done when TI flag is set and similarly data is known to be received when the Rx flag is set. The microcontroller then sends an AT command to the modem in form of string of characters serially just when the TI flag is set. After reception of a character in the SBUF register of the microcontroller (response of MODEM with the read message in its default format or ERROR message or OK message), the RI flag is set and the received character is moved into the physical memory of the microcontroller. 5.2.3. Validity Check & Display After serially receiving the characters the code then checks for start of the sender’s number and then compares the number character by character with the valid number pre stored in the memory. Since we are employing just one valid number, we are able to do the validation process dynamically i.e. without storing the new message in another location in the memory. For more than one valid numbers we would require more memory locations to first store the complete (valid/invalid) message in the memory and then perform the comparison procedure. After validity check the control flow goes into the LCD program module to display the valid message stored in the memory. In case of multiple valid numbers all invalid stored messages are deleted by proper branching in the code to the “delete-message” module.
- 45. Chapter-6 Implementation at the Institute level
- 46. 6.1 Overview Information sharing holds an important role in the daily work of our institute LDRP-ITR. Thecurrent means of information transfer are notice and circulars. New notice or circular isonly checked at the end of the day. This makes the process very time consuming and inefficient. Looking into current trend of information transfer in the campus, it is seen that important notice take time to be displayed in the notice boards. This latency is not expected in most of the cases and must be avoided. 6.2 Proposal It is proposed to implement this project at the institute level. It is proposed to place display boards at major access points. These include canteens, entrance gate, hostel area etc. But, the The GSM based display toolkit can be used as a add-on to these display boards and make it truly wireless. The display board programs itself with the help of theincoming SMS with proper validation. The valid senders may include the Director, Deans and Registrars. The centralized system can be placed as the Computer Center for access by any other valid users with authentications. SMS from these users is treated to be valid and is displayed. Other SMS from any other mobile phone is discarded. Thus information from valid sources can be broadcasted easily. Such a system proves to be helpful for immediate information transfer and can be easily implemented at the institute level.
- 48. 7.1 Conclusion The prototype of the GSM based display toolkit was efficiently designed. This prototype has facilities to be integrated with a display board thus making it truly mobile. The toolkit accepts the SMS, stores it, validates it and then displays it in the LCD module. The SMS is deleted from the SIM each time it is read, thus making room for the next SMS. The major constraints incorporated are the use of ‘*’ as the termination character of the SMS and the display of one SMS as a time. These limitations can be removed by the use of higher end microcontrollers and extended RAM. The prototype can be implemented using commercial display boards. In this case, it can solve the problem of instant information transfer in the campus. 7.2 Future Improvements The use of microcontroller in place of a general purpose computer allows us to theorize on many further improvements on this project prototype. Temperature display during periods wherein no message buffers are empty is one such theoretical improvement that is very possible. The ideal state of the microcontroller is when the indices or storage space in the SIM memory are empty and no new message is there to display. With proper use of interrupt routines the incoming message acts as an interrupt, the temperature display is halted and the control flow jumps over to the specific interrupt service routine which first validates the sender’s number and then displays the information field. Another very interesting and significant improvement would be to accommodate multiple receiver MODEMS at the different positions in a geographical area carrying duplicate SIM cards. With the help of principles of TDMA technique, we can choose to simulcast and /or broadcast important notifications. After a display board receives the valid message through the MODEM and displays it, it withdraws its identification from the network & synchronously another nearby MODEM signs itself into the network and starts to receive the message. The message is broadcast by the mobile switching center for a continuous
- 49. time period during which as many possible display board MODEMS “catch” the message and display it as per the constraint of validation. Multilingual display can be another added variation of the project. The display boards are one of the single most important media for information transfer to the maximum number of end users. This feature can be added by programming the microcontroller to use different encoding decoding schemes in different areas as per thelocal language. This will ensure the increase in the number of informed users. Graphical display can also be considered as a long term but achievable and target able output. MMS technology along with relatively high end microcontrollers to carry on the tasks of graphics encoding and decoding along with a more expansive bank of usable memory can make this task a walk in the park.
- 50. References Websites: http://en.wikipedia.org/wiki/Wikipedia http://www.atmel.com/ http://images.google.com http://www.8052.com http://www.datasheetcatalog.com http://www.keil.com/forum/docs Documents: Datasheet : MATRIX SIMADO GDT11 GSM MODEM Manual Datasheet: ATMEL 89S52 Microcontroller Datasheet : LCD HD44780 Datasheet: MAX232 from Texas Instruments