Hc 06

Guangzhou HC Information Technology Co., Ltd.


Product Data Sheet

Module Data Sheet
Rev 1
1．0 2.0 2.1 2.2
2006/6/18 2006/9/6 2010/4/22 2011/4/6

MODEL :
DRAWN BY : Ling Xin HC-06

Description::
CHECKED BY : Eric Huang BC04 has external 8M Flash and EDR module
HC-06 is industrial, and compatible with civil HC-04

APPD. BY： Simon Mok REV: 2.0 Page :

Former version
HC-06 is the higher version of LV_BC_2.0. Linvor is the former of wavesen.
introduction

www.wavesen.com Phone: 020-84083341 Fax: 020-84332079 QQ:1043073574
Address: Room 527, No.13, Jiangong Road, Tianhe software park, Tianhe district, Guangzhou Post: 510660
Technology consultant: support@wavesen.com Business consultant:sales@wavesen.com
Complaint and suggestion: sunbirdit@hotmail.com


Contents
1. Product’s picture

2. Feature

3. Pins description

4. The parameters and mode of product

5. Block diagram

6. Debugging device

7. Characteristic of test

8. Test diagram

9. AT command set



1. Product’s picture

Figure 1 A Bluetooth module



Figure 2. A Bluetooth module size

Figure 3 50 pieces chips in an anti-static blister package.



2. Feature
 Wireless transceiver
 Sensitivity (Bit error rate) can reach -80dBm.
 The change range of output’s power: -4 - +6dBm.
 Function description (perfect Bluetooth solution)
 Has an EDR module; and the change range of modulation depth: 2Mbps - 3Mbps.
 Has a build-in 2.4GHz antenna; user needn’t test antenna.
 Has the external 8Mbit FLASH
 Can work at the low voltage (3.1V~4.2V). The current in pairing is in the range of 30～40mA.
The current in communication is 8mA.
 Standard HCI Port (UART or USB)
 USB Protocol: Full Speed USB1.1, Compliant With 2.0
 This module can be used in the SMD.
 It’s made through RoHS process.
 The board PIN is half hole size.
 Has a 2.4GHz digital wireless transceiver.
 Bases at CSR BC04 Bluetooth technology.
 Has the function of adaptive frequency hopping.
 Small (27mm×13mm×2mm)
 Peripherals circuit is simple.
 It’s at the Bluetooth class 2 power level.
 Storage temperature range: -40 ℃ - 85℃，work temperature range: -25 ℃ - +75℃
 Any wave inter Interference: 2.4MHz，the power of emitting: 3 dBm.
 Bit error rate: 0. Only the signal decays at the transmission link, bit error may be produced. For
example, when RS232 or TTL is being processed, some signals may decay.

 Low power consumption
 Has high-performance wireless transceiver system
 Low Cost


 Application fields:
 Bluetooth Car Handsfree Device
 Bluetooth GPS
 Bluetooth PCMCIA , USB Dongle
 Bluetooth Data Transfer
 Software
 CSR

3．PINs description

Figure 3 PIN configuration
The PINs at this block diagram is as same as the physical one.
PIN Name PIN # Pad type Description Note
GND 13 21 22 VSS Ground pot
Integrated 1.8V (+) supply with
1V8 14 VDD On-chip linear regulator output
within 1.7-1.9V
VCC 12 3.3V
AIO0 9 Bi-Directional Programmable input/output line
AIO1 10 Bi-Directional Programmable input/output line


Bi-Directional Programmable input/output line,
PIO0 23
RX EN control output for LNA(if fitted)
Bi-Directional Programmable input/output line,
PIO1 24
TX EN control output for PA(if fitted)
PIO2 25 Bi-Directional Programmable input/output line
PIO6 29 Bi-Directional Programmable input/output line CLK_REQ
PIO7 30 Bi-Directional Programmable input/output line CLK_OUT
CMOS Input with
RESETB 11 weak intemal
pull-down
CMOS output,
UART_RTS 4 tri-stable with weak UART request to send, active low
internal pull-up
CMOS input with
UART_CTS 3 weak internal UART clear to send, active low
pull-down
CMOS input with
UART_RX 2 weak internal UART Data input
pull-down
CMOS output,
Tri-stable with
UART_TX 1 UART Data output
weak internal
pull-up
CMOS input with
SPI_MOSI 17 weak internal Serial peripheral interface data input
pull-down
CMOS input with Chip select for serial peripheral
SPI_CSB 16
weak internal interface, active low



pull-up
CMOS input with
SPI_CLK 19 weak internal Serial peripheral interface clock
pull-down
CMOS input with
Serial peripheral interface data
SPI_MISO 18 weak internal
Output
pull-down

USB_- 15 Bi-Directional

USB_+ 20 Bi-Directional

Default :
1.8V
1.8V 14 1.8V external power supply input
internal powe
r supply.

PCM_CLK 5 Bi-Directional

PCM_OUT 6 CMOS output

PCM_IN 7 CMOS Input

PCM_SYNC 8 Bi-Directional



4. The parameters and mode of product

If you want more information, please visit www.wavesen.com.



5. Block diagram

Figure 5 Block diagram 1

Figure 5 Block diagram 2



HC-04/06 master device has a function of remembering the last paired slave device. As a master
device, it will search the last paired salve device until the connection is built. But if the WAKEUP
bottom is pressed, HC-04/06 will lose the memory and research the new slave device.

6. Debugging device
6.1 Device
PC, hardware, 3G， Frequency Counter (SP3386), 3.15V DC power supply, Shielding，
3G Bluetooth
Test box.
6.2 Software

7. Characteristic of test
Test Condition 25℃ RH 65%
Min Typ Max Unit
1. Carrier Freq. ( ISM Band ) 2.4 2.4835 MHz
2. RF O/P Power -6 2 4 dBm
3. Step size of Power control 2 8 dB
4. Freq. Offset ( Typical Carrier freq.) -75 75 KHz
5. Carrier Freq. drift ( Hopping on, drift rate/50uS ) -20 20 KHz
1 slot packet -25 25 KHz
3 slot packet -40 -40 KHz
6. Average Freq. Deviations ( Hopping off, modulation ) 140 175 KHz
Freq. Deviation 115 KHz
Ratio of Freq. Deviation 0.8
7 . Receive Sensitivity @< 0.1% BER( Bit error rate )-83 dBm



8. Test diagram

3GHz Ferq.
Counter RS232

CH C

COM 1
RF O/P
LPT1
UUT Interface
Computer
circuit
SPI

Shielding Box

Fig 1. Programming and Freq. Alignment

GPIB
Bluetooth test
Computer
set

RF I/P COM 1
LP1
RS232

RF Port

UUT SPI

Shielding Box

Fig 2 RF parameter Test Procedure


9．AT command set
The way to the AT command mode: supply power to the module, it will enter to the AT mode if it
needn’t pair. The interval of command is about 1 second.
Default parameter: Baud rate:9600N81, ID: linvor, Password:1234
1. Test communication
Send: AT (please send it every second)
Back: OK

2. Reset the Bluetooth serial baud rate
Send: AT+BAUD1
Back: OK1200
Send: AT+BAUD2
Back: OK2400
……
1---------1200
2---------2400
3---------4800
4---------9600 (Default)
5---------19200
6---------38400
7---------57600
8---------115200
9---------230400
A---------460800
B---------921600
C---------1382400
PC can’t support the baud rate lager than 115200. The solution is: make the MCU have higher baud
rate (lager than 115200) through programming, and reset the baud rate to low level through the AT
command.
The baud rate reset by the AT command can be kept for the next time even though the power is cut
off.

3. Reset the Bluetooth name
Send: AT+NAMEname
Back: OKname


Parameter name: Name needed to be set (20 characters limited)
Example:
Send: AT+NAMEbill_gates
Back: OKname
Now, the Bluetooth name is reset to be “bill_gates”
The parameter can be kept even though the power is cut off. User can see the new Bluetooth name
in PDA refresh service. (Note: The name is limited in 20 characters.)

4. change the Bluetooth pair password
Send: AT+PINxxxx
Back:OKsetpin
Parameter xxxx: The pair password needed to be set, is a 4-bits number. This command can be used
in the master and slave module. At some occasions, the master module may be asked to enter the
password when the master module tries to connect the slave module (adapter or cell-phone). Only if the
password is entered, the successful connection can be built. At the other occasions, the pair can be finish
automatically if the master module can search the proper slave module and the password is correct.
Besides the paired slave module, the master can connect the other devices who have slave module, such
as Bluetooth digital camera, Bluetooth GPS, Bluetooth serial printer etc.
Example:
Send: AT+PIN8888
Back: OKsetpin
Then the password is changed to be 8888, while the default is 1234.
This parameter can be kept even though the power is cut off.

5. No parity check ( The version, higher than V1.5, can use this command )
Send: AT+PN (This is the default value)
Back: OK NONE

6. Set odd parity check ( The version, higher than V1.5, can use this command )
Send: AT+PO
Back: OK ODD

7. Set even parity check( The version, higher than V1.5, can use this command )
Send: AT+PE
Back: OK EVEN



8. Get the AT version
Send: AT+VERSION
Back: LinvorV1.n


Hc 06

More Related Content

What's hot (20)

Similar to Hc 06 (20)

Hc 06