How to Select Your Next Oscilloscope

Keysight Technologies
How to Select Your Next Oscilloscope:
12 Tips on What to Consider
Before you Buy
Application Note

Introduction
You rely on your oscilloscope every day, so selecting the right one to meet your specific measurement
needs and budget is an important task. Comparing different manufacturers’ oscilloscopes and their
various specifications and features can be time-consuming and confusing. The 12 oscilloscope
selection tips presented in this application note are intended to accelerate your selection process
and help you avoid some common pitfalls.

03 | Keysight | How to Select Your Next Oscilloscope: 12 Tips on What to Consider Before you Buy - Application Note
Select an oscilloscope that has sufficient band-
width to accurately capture the highest frequency
content of your signals
There are a variety of oscilloscope specifications that determine
how accurately signals can be captured and measured. But an
oscilloscope’s primary specification is its bandwidth. So what do
we mean by “bandwidth”? All oscilloscopes exhibit a low-pass
frequency response that rolls-off at higher frequencies, as shown
in Figure 1. Most oscilloscopes with bandwidth specifications of 1
GHz and below typically have what is called a Gaussian frequency
response, which approximates the characteristics of a single-pole
low-pass filter. The lowest frequency at which the input signal is
attenuated by 3 dB is considered the oscilloscope’s bandwidth.
Signal attenuation at the –3 dB frequency translates into approx-
imately –30% amplitude error. In other words, if you input a 1 Vp-
p, 100-MHz sine wave into a 100-MHz bandwidth oscilloscope,
the measured peak-to-peak voltage using this oscilloscope would
be in the range of 700 mVp-p (–3 dB = 20 Log (0.707/1.0). So you
cannot expect to make accurate measurements on signals that
have significant frequencies near your oscilloscope’s bandwidth.
So how much bandwidth is required for your particular measure-
ment applications? For purely analog signal measurements, you
should choose an oscilloscope that has a bandwidth specification
at least three times higher than the highest sine wave frequencies
you may need to measure. At 1/3 of an oscilloscope’s bandwidth
specification, signal attenuation is minimal. But what about re-
quired bandwidth for digital applications, the main use of today’s
oscilloscopes? As a rule of thumb, Keysight Technologies, Inc.
recommends you choose an oscilloscope that has a bandwidth
at least five times the highest clock rate in your systems. For
example, if the highest clock rate in your designs is 100 MHz, then
you should choose an oscilloscope with a bandwidth of 500 MHz
or higher. If your oscilloscope meets this criterion, it will be able
to capture up to the fifth harmonic with minimum signal attenua-
tion. The fifth harmonic of the signal is critical in determining the
overall shape of your digital signals.
Tip #1: Bandwidth
Figure 2. 100-MHz clock signal captured on a 100-MHz bandwidth
oscilloscope.
Figure 1. Oscilloscopes exhibit a low-pass frequency response that rolls-off higher
frequencies.
Figure 2 shows an 100-MHz bandwidth oscilloscope capturing
and displaying a 100-MHz digital clock signal. In this case, the
oscilloscope attenuates the higher frequency components and
basically just shows the 100-MHz sine wave fundamental fre-
quency of this signal. This oscilloscope has insufficient bandwidth
to capture this signal. Figure 3 shows the same 100-MHz clock
signal captured on a 500-MHz bandwidth oscilloscope. We can
now see and measure more details of this digital signal using this
higher bandwidth oscilloscope.
0 dB
-3 dB
fBW
Frequency
Attenuation

Figure 3. 100-MHz clock signal captured on a 500-MHz bandwidth
oscilloscope.
Note that the 5-to-1 rule-of-thumb recommendation (oscillo-
scope bandwidth relative to clock rate) does not take into account
lower clock-rate signals that have relatively fast edge speeds.
These signals may contain significant frequency components
beyond the fifth harmonic. To learn more about how to determine
required bandwidth based on signal edge speeds, refer to Key-
sight’s application note Evaluating Oscilloscope Bandwidths for
Your Applications, which is listed in the related literature section
at the end of this document.
Protect your investment with bandwidth upgradability
Keysight Technologies’ InfiniiVision and Infiniium Series oscil-
loscopes come in various bandwidths ranging from 70 MHz to
63 GHz. Their bandwidths can also be upgraded after the initial
purchase. This means you can now protect your oscilloscope
investment. Perhaps a 100-MHz bandwidth oscilloscope is all you
need and can afford today, but if your signal speeds increase in
two years, you may then need a 500-MHz oscilloscope to make
accurate measurements on your higher speed designs. No prob-
lem! If you purchase a Keysight InfiniiVision X-Series or Infiniium
Series oscilloscope today, you can easily upgrade the bandwidth
in the future.
Tip #1: Bandwidth (continued)

Select an oscilloscope that has a maximum speci-
fied sample rate fast enough to deliver the oscillo-
scope’s specified real-time
bandwidth
Closely related to an oscilloscope’s real-time bandwidth is its
maximum specified sample rate. “Real-time” simply means the
oscilloscope can capture and display signals commensurate with
the oscilloscope’s specified bandwidth in a single acquisition (not
repetitive).
Most engineers are familiar with
Nyquist’s Sampling Theorem. The
theorem states that for a limited
bandwidth (band-limited) signal with
maximum frequency fmax
, the equal-
ly-spaced sampling frequency fs
must
be greater than twice the maximum
frequency fmax
, i.e., fs
> 2•fmax
, for the
signal to be uniquely reconstructed
without aliasing.
Today fmax
is commonly known as the
Nyquist frequency (fN
). The mistake some engineers make is they
sometimes assume fmax
, or fN
, is the same as fBW
(oscilloscope
bandwidth). With this assumption, you might think the minimum
required sample rate for an oscilloscope of a particular specified
bandwidth is just twice the oscilloscope’s real-time bandwidth
specification, as shown in Figure 4. But, fmax
is NOT the same as
fBW
, unless the oscilloscope had a brick-wall filter response.
As you learned in “Tip #1,” oscilloscopes with bandwidth specifi-
cations of 1 GHz and below typically have a Gaussian frequency
response. This means that although the oscilloscope attenuates
the amplitude of signal frequencies above its –3 dB bandwidth
frequency point, it does not entirely eliminate these higher
frequency components. The aliased frequency components are
shown by the red hashed area in Figure 4. Therefore fmax
is always
higher than fBW
for an oscilloscope.
Tip #2: Sample rate
Figure 4. Aliased frequency components when the oscilloscope’s bandwidth is
specified at ½ its sample rate for oscilloscopes that exhibit a Gaussian frequency
response.
Keysight recommends an oscilloscope’s maximum specified
sample rate should be at least four to five times higher than the
scope’s specified real-time bandwidth, as shown in Figure 5. With
this criterion, the oscilloscope’s sin(x)/x waveform reconstruction
filter can accurately reproduce the wave shape of higher speed
signals with resolution in the tens of picoseconds range.
Figure 5. Aliased frequency components when the oscilloscope’s bandwidth is
specified at ¼ the oscilloscope’s sample rate.
Dr. Harry Nyquist

Many higher bandwidth oscilloscopes have a faster/sharper
roll-off frequency response as shown in Figure 6. We call this
type of frequency response a “maximally-flat” response. Since an
oscilloscope with a maximally-flat response attenuates frequency
components beyond the Nyquist frequency to a higher degree,
and begins to approach the ideal characteristics of a theoretical
brick-wall filter, not as many samples are required to produce a
good representation of the input signal while using digital filtering
to reconstruct the waveform. Oscilloscopes with this type of
frequency response can theoretically specify the bandwidth at
fS
/2.5.
Figure 6. Aliased frequency components when the oscilloscope’s
bandwidth is specified at 1/(2.5) of the scope’s sample rate for
oscilloscopes that exhibit a “maximally-flat” frequency response.
To learn more about oscilloscope real-time sampling, refer to
Keysight’s application note Evaluating Oscilloscope Sample
Rates Versus Sampling Fidelity, which is listed in the related
literature section at the end of this document.
The core component of all digital storage oscilloscopes is the
high-speed analog-to-digital converter (ADC) system. Keysight
invests heavily in ADC technology and has the highest sample
rate and highest fidelity monolithic ADCs in the oscilloscope
industry. Keysight’s entry-level 2000 X-Series InfiniiVision
oscilloscopes can sample at rates up to 2 GSa/s, and Keysight’s
higher performance 90000 Q-Series Infiniium
oscilloscopes can sample at rates up to 160 GSa/s.
Tip #2: Sample rate (continued)

Select an oscilloscope that has sufficient
acquisition memory to capture your most
complex signals with high resolution
Closely related to an oscilloscope’s maximum sample rate is its
maximum available acquisition memory depth. Even though an
oscilloscope’s banner specifications may list a high maximum
sample rate, this does not mean that the oscilloscope always
samples at this high rate. Oscilloscopes sample at their fastest
rates when the timebase is set on one of the faster time ranges.
But when the timebase is set to slower ranges to capture longer
time spans across the oscilloscope’s display, the scope automat-
ically reduces the sample rate based on the available acquisition
memory.
For example, let’s assume that an entry-level oscilloscope has
a maximum sample rate of 1 GSa/s and a memory depth of 10 k
points. If the oscilloscope’s timebase is set at 10 ns/div in order to
capture 100 ns of signal activity across the oscilloscope’s screen
(10 ns/div x 10 divisions = 100 ns time span), the oscilloscope
needs just 100 points of acquisition memory to fill the screen
while sampling at its maximum sample rate of 1 GSa/s (100 ns
time span x 1 GSa/s = 100 samples). No problem! But if you set
the oscilloscope’s timebase to 10 µs/div to capture 100 µs of sig-
nal activity, the oscilloscope will automatically reduce its sample
rate to 100 MSa/s (10 k samples/100 µs time-span = 100 MSa/s).
Maintaining the oscilloscope’s fastest sample rate at the slower
timebase ranges requires that the scope have additional acquisi-
tion memory. Determining the amount of acquisition memory you
require involves a pretty simple equation based on the longest
time span of a complex signal you need to capture and the maxi-
mum sample rate at which you want the oscilloscope to sample.
Acquisition Memory = Time Span x Required Sample Rate
In Figure 7, we show a Keysight 3000 X-Series oscilloscope cap-
turing a complex digital signal at 100 µs/div for a total capture
time of 1 ms. Since this oscilloscope has up to 4,000,000 points
of acquisition memory, it can maintain its maximum sample
rate of 4 GSa/s at this timebase setting. In the upper half of the
oscilloscope’s display, we can see the entire captured wave-
form. In the lower half of the oscilloscope’s display, we can see a
“zoomed-in” display of a small portion of the captured waveform,
revealing a runt pulse that is approximately 100 ns wide.
Tip #3: Memory depth
Figure 7. Capturing a complex stream of digital pulses using deep memory.
Although you may intuitively think deeper is always better, using
deep memory often means making tradeoffs when using many
oscilloscopes on the market today. First of all, oscilloscopes with
deep memory are typically priced higher. Second, acquiring long
waveforms using deep memory requires additional waveform pro-
cessing time. This typically means waveform update rates will be
reduced, sometimes significantly. For this reason, most oscillo-
scopes on the market today have manual memory-depth selec-
tions, and the typical default memory depth setting is usually
relatively shallow (10 to 100 k). If you want to use deep memory,
then you must manually turn it on and deal with the update rate
tradeoff. This means you must know when it is important to use
deep memory and when it is not.
With Keysight’s exclusive MegaZoom technology, you don’t have
to be an oscilloscope expert. MegaZoom automatically selects
deeper memory when needed in order to maintain fast sample
rates. And with this custom technology, the oscilloscope always
remains responsive—even when using deep memory.

Segmented Memory
Some oscilloscopes have a special mode of operation called “seg-
mented memory acquisition.” Segmented memory can effectively
extend the oscilloscope’s total acquisition time by dividing its
available acquisition memory into smaller memory segments as
illustrated in Figure 8. The oscilloscope then selectively digitizes
just the important portions of the waveform under test at a high
sample rate and then time-tags each segment so you know the
precise time between each occurrence of trigger events. This
enables your oscilloscope to capture many successive single-shot
waveforms with a very fast re-arm time — without missing im-
portant signal information. This mode of operation is especially
useful when capturing burst of signals. Examples of burst-type
signals would be pulsed radar, laser bursts, as well as packetized
serial bus signals. To learn more about oscilloscope segmented
memory acquisition, refer to Keysight’s application note, Using
Oscilloscope Segmented Memory for Serial Bus Applications,
which is listed in the related literature section at the end of this
document.
Segmented Memory acquisition is available on all of Keysight’s
InfiniiVision X-Series and Infiniium Series oscilloscopes. When the
absolute deepest memory is required, Keysight’s Infiniium Series
oscilloscopes offer up to 2 GB of acquisition memory so you can
capture the longest time-span at the oscilloscope’s maximum
sample rate.
Tip #3: Memory depth (continued)

Tip #4: Number of channels
Select an oscilloscope that has a sufficient number of channels of
acquisition so that you can perform critical time-correlated mea-
surements across multiple waveforms
The number of oscilloscope channels you require will depend on how many signals you
need to observe and compare in relationship to each other. At the heart of most of to-
day’s embedded designs is a microcontroller (MCU) as shown in the simplified schematic
of Figure 9. Many MCUs are actually mixed-signal devices with multiple analog, digital,
and serial I/O signals that interface to the real-world, which is always analog in nature.
As today’s mixed-signal designs have become more complex, more channels of acquisi-
tion and display may be required. Two- and four-channel oscilloscopes are very common
today. If more than four analog channels of acquisition are required, your choices be-
come very limited, But there is another alternative: a Mixed Signal Oscilloscope (some-
times called an “MSO”).
MSOs combine all of the measurement capabilities of oscilloscopes with some of the
measurement capabilities of logic analyzers and serial bus protocol analyzers. MSOs
have three primary attributes. The most obvious attribute is the ability to simultaneously
capture multiple oscilloscope and logic signals with a time-correlated display of wave-
forms. Just think of it as having a few channels with high vertical resolution (typically 8
bits) plus several additional channels with very low vertical resolution (1 bit).
Voltage
Reference
MCU
EEPROM
HOST
IR-IF
4
n
TX
RCV
VccClk
Data
2.5
PWM
I2C Comm.
Serial I/O
PWM Output
GND
GND 5V
Parallel I/O
GND
Analog +
Neutral
Analog -
Analog Inputs
Figure 9. Typical MCU-based embedded design.

Another attribute is that although MSOs may lack the large number of digital channels of
a logic analyzer, one of the MSO’s primary advantages is its familiar use-model, which is
that of an oscilloscope. And lastly, with the additional logic channels available in MSOs,
users now have many more triggering possibilities that can be used to “zero-in” on spe-
cific parallel and serial bus I/O interaction in today’s mixed-signal designs.
In Figure 10 we show a Keysight MSO capturing the input of a MCU-controlled digi-
tal-to-analog converter (DAC) using its digital channels of acquisition, while monitoring
the output of the DAC with a single analog channel of acquisition. In this example the
MSO was setup to trigger on a logical pattern condition of the input of the DAC when it
was at its lowest value of 0000 1010 (1AHEX
).
Figure 10. MSOs can capture and display multiple analog and digital signals simultaneously providing an inte-
grated and time-correlated display of multiple waveforms.
To learn more about making measurements with a mixed signal oscilloscope (MSO), refer
to Keysight’s application note Evaluating Oscilloscopes to Debug Mixed-signal Designs,
which is listed in the related literature section at the end of this document.
Keysight’s InfiniiVision and Infiniium oscilloscopes can be pre-configured and purchased
as either DSO or MSO models. DSO models can also be easily upgraded to MSO models
after purchase.
Tip #4: Number of channels (continued)

Select an oscilloscope that has a fast enough waveform update rate
to capture random and infrequent events to help you debug your
designs faster
Although often overlooked when evaluating performance of various oscilloscopes for
purchase, waveform update rates can be extremely important — sometimes just as
important as the traditional banner specifications including bandwidth, sample rate, and
memory depth. Even though an oscilloscope’s waveform update rate may appear fast
when viewing repetitively captured waveforms on your oscilloscope’s display, “fast” is
relative. For example, a few hundred waveforms per second will certainly appear lively,
but statistically speaking this can be very slow if you are attempting to capture a random
and infrequent event that may happen just once in a million occurrences of a signal.
When you debug new designs, waveform update rates can be critical — especially when
you are attempting to find and debug infrequent or intermittent problems. These are the
toughest kinds of problems to solve. Faster waveform update rates improve the oscillo-
scope’s probability of capturing illusive events.
All oscilloscopes have an inherent characteristic called “dead-time” or “blind time.” This
is the time between each repetitive acquisition of the oscilloscope when it is processing
the previously acquired waveform. Unfortunately, oscilloscope dead-times can some-
times be orders of magnitude longer than acquisition times. During the oscilloscope’s
dead-time, any signal activity that may be occurring will be missed as shown in Figure
11. Note the two glitches that occurred during the oscilloscope’s dead time – not during
its acquisition time.
Acquisition
time
Acquisition
time
Dead-time
Figure 11. Oscilloscope dead-time versus display acquisition time.
Tip #5: Waveform update rate

Figure 12. The Keysight MSO/DSO3000 X-Series oscilloscope reliably captures the infrequently occurring meta-
stable state while updating at 1,000,000 waveforms per second.
Other oscilloscopes in this class may update waveforms only 2000 to 3000 times per
second. This means that these oscilloscopes would have less than a 1% probability of
capturing and displaying an infrequent glitch such as this within 5 seconds. To learn
more about oscilloscope waveform update rates and how to compute statistical glitch
capture probabilities, refer to Keysight’s application note, Oscilloscope Waveform
Update Rate Determines Probability of Capturing Elusive Events, which is listed in the
related literature section at the end of this document.
Because of oscilloscope dead-time, capturing random and infrequent events with an os-
cilloscope becomes a gamble — much like rolling dice. The more times you roll the dice,
the higher the probability of obtaining a specific combination of numbers. Likewise, the
more often a oscilloscope updates waveforms for a given amount of observation time,
the higher the probability of capturing and viewing an elusive event — one that you may
not even know exists.
In Figure 12 we show a Keysight InfiniiVision X-Series oscilloscope capturing an infre-
quent metastable state (glitch) that occurs approximately 5 times per second. With a
maximum waveform update rate of more than 1,000,000 waveforms per second, this
oscilloscope has a 92% probability of capturing this glitch within 5 seconds. In this ex-
ample, the oscilloscope captured the metastable state several times.
Tip #5: Waveform update rate (continued)

Tip #6: Triggering
Select an oscilloscope that has the types of ad-
vanced triggering that you may need to help you
isolate waveform acquisitions on your most com-
plex signals
An oscilloscope’s triggering capability is one of its most important
aspects. Triggering allows you to synchronize the oscilloscope’s
acquisition and display of waveforms on particular parts of a
signal. You can think of oscilloscope triggering simply as synchro-
nized picture taking.
The most common type of oscilloscope triggering is that of trig-
gering on a simple edge crossing. For example, trigger on a rising
edge of channel-1 when the signal crosses a particular voltage
level (trigger level) in a positive direction as shown in Figure 13.
All oscilloscopes have this capability, and it is probably still the
most commonly used type of triggering. But as today’s digital de-
signs have become more complex, you may need to further quali-
fy/filter your oscilloscope’s triggering on particular characteristics
or combinations of input signals in order to zero-in, capture, and
view a particular portion of a complex input signal.
Some oscilloscopes have the ability to trigger on pulses that
meet a particular timing qualification. For example, trigger only
when a pulse is less than 20 ns wide. This type of triggering
(qualified pulse-width) can be very useful for triggering on unsus-
pected glitches.
Another type of triggering that is common in many of today’s
oscilloscopes is pattern triggering. Pattern triggering allows
you to set up the oscilloscope to trigger on a logical/Boolean
combination of highs (or 1s) and lows (or 0s) across two or more
input channels. This can be especially useful when using a Mixed
Signal Oscilloscope (MSO), which can provide up to 20 analog
and digital channels of acquisition.
More advanced oscilloscopes even provide triggering that can
synchronize on signals that have parametric violations. In other
words, trigger only if the input signal violates a particular para-
metric condition such as reduced pulse height (runt trigger), edge
speed violation (rise/fall time), or perhaps a clock to data timing
violation (setup and hold time trigger).
Figure 14 shows a Keysight oscilloscope triggering on a positive
pulse with reduced amplitude using the oscilloscope’s Runt trig-
gering selection. If this runt pulse occurred just once in a million
cycles of the digital pulse stream, capturing this signal while
using standard edge triggering would be like looking for a needle
in a haystack. This scope can also trigger on negative runts, as
well as runt pulses of a specific pulse width.
Figure 13. Triggering on a rising edge of a digital pulse.
Figure 14. Triggering on a reduced amplitude pulse using Runt triggering.

Even with advanced parametric triggering capability in an oscillo-
scope, determining which special trigger mode to select and how
to set it up can sometimes be confusing. This is where Keysight’s
hardware-based InfiniiScan Zone Trigger steps in. Figure 15
shows an example of an infrequent non-monotonic edge while the
oscilloscope is set up to trigger on any rising edge of the input
signal.
Figure 15. The oscilloscope’s fast waveform update rate reveals an infrequent
non-monotonic edge.
With Zone Trigger, you can simply draw a box (zone) in the region
of the anomaly, and then the oscilloscope isolates just the infre-
quently occurring edges with the non-monotonic edge as shown
in Figure 16.
Figure 16. InfiniiScan Zone trigger isolates the infrequent non-monotonic edge.
To learn more about InfiniiScan Zone triggering, refer to Keysight’s
application note Synchronizing on Infrequent Anomalies and Com-
plex Signals using InfiniiScan Zone Trigger, which
is listed in the related literature section at the end of this
document.
Tip #6: Triggering (continued)

Tip #7: Display quality
Figure 17. Multiple levels of trace intensity gradation reveals distribution of jitter.
Select an oscilloscope that provides multiple
levels of trace intensity gradation in order to
display subtle waveform details and signal
anomalies
The quality of your oscilloscope’s display can make a big differ-
ence in your ability to effectively troubleshoot your designs. If
your oscilloscope has a low-quality display, you may not be able
to see subtle waveform details. An oscilloscope that is capable of
showing signal intensity gradations can reveal important wave-
form details in a wide variety of both analog and digital signal
applications, including relative distribution of noise, jitter, and
signal anomalies.
Engineers have traditionally thought of digital storage oscillo-
scopes (DSOs) as two-dimensional instruments that graphically
display just voltage versus time. But there is actually a third
dimension to an oscilloscope: the z-axis. This third dimension
shows continuous waveform intensity gradation as a function of
the frequency-of-occurrence of signals at particular
X-Y locations.
In analog oscilloscope technology, intensity modulation is a
natural phenomenon of the oscilloscope’s vector-type display,
which is swept with an electron beam. Due to early limitations of
digital display technology, this third dimension, intensity modula-
tion, was missing when digital oscilloscopes began replacing their
analog counterparts. But some of today’s digital storage oscillo-
scopes (DSOs) now provide similar — and sometimes superior —
display quality using custom digital signal processing technology.
Figure 17 shows a Keysight InfiniiVision X-Series oscilloscope that
is set up to monitor jitter on a digital signal. With the oscillo-
scope’s fast waveform update rate (up to 1,000,000 waveforms/
sec) along with 64 levels of trace intensity gradation, we can
make qualitative judgments about the nature of the distribution
of noise and jitter. We know traces that appear bright occur most
often, while traces that appear dim occur least often.

Figure 18. Most entry-level scopes provide just one or two levels of trace intensity
gradation.
Trace intensity gradation is also extremely important when cap-
turing and monitoring complex modulated analog signals, such
as video. Figure 19 shows an InfiniiVision X-Series oscilloscope
displaying three fields of an NTSC video signal, along with a
zoomed-in display of a single line of interlaced video.
In addition to the number of levels of trace intensity gradation,
other factors that should be considered regarding an oscillo-
scope’s display quality include update rate, display size, display
resolution, viewing angle, color versus monochrome, and user-se-
lectable display modes such as variable and infinite persistence.
Figure 19. High levels of display quality are required when viewing complex modu-
lated signals such as video.
To learn more about oscilloscope display quality, refer to Key-
sight’s application note Oscilloscope Display Quality Impacts
Ability to View Subtle Signal Details, which is listed in the relat-
ed literature section at the end of this document.
First generation digital storage oscilloscopes (DSOs), as well as
most of today’s entry-level oscilloscopes provide just 1 to 2 levels
of trace intensity gradation as shown in Figure 18. This makes it
impossible to make qualitative judgments about complex signal
modulation since all traces have the same exact intensity. Does
the jitter have a Gaussian or even distribution? Does the jitter
include deterministic components? We don’t know.
Tip #7: Display quality (continued)

Tip #8: Serial bus applications
Figure 20. Triggering on and decoding a CAN serial bus using a Keysight
InfiniiVision X-Series oscilloscope.
Select an oscilloscope that can trigger on and
decode serial buses to help you debug your
designs faster
Serial buses such as I2
C, SPI, RS232/UART, CAN, USB, etc., are
pervasive in many of today’s digital and mixed-signal designs.
Verifying proper bus communication along with analog signal
quality measurements requires an oscilloscope. Many engineers
and technicians verify serial bus communication with an oscillo-
scope using a technique known as “visual bit counting”. But this
manual method of decoding a serial bus can be time consuming
and prone to errors. However, many of today’s DSOs and MSOs
have optional built-in serial bus protocol decode and triggering
capabilities. If your designs include serial bus technology, then
selecting an oscilloscope that can decode and trigger on these
buses can be a significant time-saver to help you debug your
systems faster.
Most oscilloscopes on the market today that have serial bus
analysis capabilities utilize software-based decoding techniques.
With software-based decoding, waveform and decode update
rates tend to be slow (sometimes seconds per update). This is
especially true when using oscilloscopes with deep memory,
which are often required to capture multiple packetized serial bus
signals. And when analyzing multiple serial buses simultaneously,
software techniques can make protocol-specific decode update
rates even slower.
Keysight’s InfiniiVision X-Series oscilloscopes utilize hard-
ware-based decoding to provide virtual real-time updates. Faster
decoding with hardware-based technology enhances oscillo-
scope usability and, more importantly, the probability of captur-
ing infrequent serial communication errors.
Figure 20 shows a Keysight InfiniiVision X-Series oscilloscope
capturing and decoding a CAN (Controller Area Network) serial
bus, which is commonly used in many automotive and industrial
machinery applications, including medical diagnostics equipment.
Below the waveform is the time-correlated decode trace that
shows the contents of a single packet/frame of data. The upper
half of the oscilloscope’s display shows the “lister” display, which
provides decoded information in a more familiar tabular format;
like a traditional protocol analyzer. The lister display can also be
used to search and automatically navigate to specific packets of
interest.

In addition to triggering on and decoding serial buses, it is often
necessary to perform eye-diagram mask test measurements on
serial bits. This is especially important for higher speed differen-
tial buses and/or buses that communicate over a long network.
With an eye-diagram display, all serial bits are overlaid and com-
pared to a pass/fail mask based on published industry physical
layer standards/specifications. Figure 21 shows an eye-diagram
mask measurement on a CAN serial bus, which is commonly
used in all of today’s automobiles. With a mask test rate of up
to 200,000 waveforms/sec, the scope quickly captures bits that
exhibit excessive jitter as shown by the traces color coded in red.
Figure 21. Eye-diagram mask test on a CAN serial bus using a Keysight InfiniiVision
X-Series oscilloscope.
Figure 22. USB 2.0 hi-speed compliance test performed using a Keysight Infiniium
Series oscilloscope.
To learn more about oscilloscope serial bus applications, refer to
Keysight’s data sheet Serial Bus Options for InfiniiVision X-Se-
ries Oscilloscopes, which is listed in the related literature section
at the end of this document.
Keysight’s InfiniiVision and Infiniium Series oscilloscopes offer
a broad range of serial bus protocol trigger/decode options
including:
–– I2
C/SPI
–– RS232/UART
–– USB
–– CAN/CAN FD/LIN
–– SENT
–– FlexRay
–– I2
S
–– MIL-STD 1553/ARINC 429
–– JTAG (IEEE 1149.1)
–– MIPI D-Phy
–– PCI Express
–– SATA
For many higher-speed serial buses such as USB 2.0/3.0, PCIe,
and Gigabit Ethernet, automatic pass/fail compliance testing
against published industry standards/specifications is often
required. Keysight’s Infiniium oscilloscopes offer a broad range
of optional serial bus compliance test packages. Figure 22 shows
an automated USB 2.0 hi-speed compliance test using a Keysight
Infiniium Series oscilloscope. Also available with the various com-
pliance test packages is complete report generation.
Tip #8: Serial bus applications (continued)

Tip #9: Measurements and analysis
Figure 24. Performing an FFT math operation on a digital clock waveform using a
Keysight oscilloscope.
Although most advanced waveform math functions can also be
performed offline on a PC using software like MatLab, having this
capability embedded in the oscilloscope not only makes it easier
to perform these types of advanced math functions, but can also
provide a updated display of waveform math functions in order to
show dynamic signal behavior.
As you move up in price and performance, you will find that
higher-end oscilloscopes typically have more measurement and
analysis capabilities such as advanced waveform math, automat-
ic pass/fail mask testing, and application-specific compliance
testing.
Whereas pulse parameter measurements typically perform a tim-
ing or amplitude measurement across a small portion of a wave-
form to provide an “answer,” such as the rise time or peak-to-
peak voltage, an oscilloscope’s waveform math function performs
a math operation on an entire waveform or pair of waveforms to
produce yet another waveform.
Figure 24 shows an example of an Fast Fourier Transform (FFT)
math function that was performed on a clock signal (yellow
trace). This produced the frequency domain waveform (purple
trace) that shows amplitude in dB on the vertical axis versus
frequency in Hertz on the horizontal axis. Other common math
operations that can be performed on digitized waveforms include
sum, difference, differentiate, integrate, etc.
Select an oscilloscope that can automatically
perform your required parametric measurements
and waveform math operations so you can
characterize your designs faster
One of the major advantages of today’s digital storage oscillo-
scopes (DSOs) over older analog oscilloscope technology is that
they have the ability to perform various automatic measure-
ments and analysis on digitized waveforms. You will find that
digital oscilloscopes from various vendors have a wide variety of
measurement capabilities. But nearly all of today’s DSOs provide
manually-controlled cursor/marker measurement capabilities as
well as a minimum set of automatic pulse parameter measure-
ments such as rise time, fall time, frequency, pulse width, etc. as
shown in Figure 23.
Figure 23. Performing automatic parametric amplitude and timing measurements
using a Keysight oscilloscope.

Some of today’s oscilloscopes can also perform automatic pass/
fail testing based on published industry standards/specifications.
Figure 25 shows an example of a pass/fail current harmonics
compliance test on a switch mode power supply (SMPS) using an
optional Power Measurements analysis package. If any harmon-
ics of the input signal (up to the 40th harmonic) exceed specified
standards, they are clearly marked in the test results table shown
in the upper half of the oscilloscope’s display.
Figure 26. User-defined Signal Equalization measurement using the N5430A UDF
option on an Infiniium Series oscilloscope.
Figure 25. Automatic pass/fail compliance testing using a Keysight oscilloscope.
Although today’s higher performance oscilloscopes provide a
broad array of built-in and advanced measurement functions,
sometimes you may require a special math/measurement func-
tion that is just not available in any oscilloscope.
With Keysight’s N5430A User-defined Function (UDF) licensed on
an Infiniium Series oscilloscope, you can install MATLAB on your
oscilloscope, add your favorite MATLAB.m scripts as function op-
erators, and then use them as standard waveform math functions
as illustrated by the Signal Equalization measurement shown in
Figure 26.
Tip #9: Measurements and analysis (continued)

Tip #10: Connectivity and documentation
Select an oscilloscope that meets your particular
hardware connectivity, test automation, and electronic
documentation requirements
Many of today’s digital oscilloscopes are used in automated test environments in both
RD and manufacturing. Automated testing requires that the oscilloscope be connected
to a computer via various possible connectivity ports. Most older DSOs were limited to
GPIB and/or RS232 connectivity. Most of today’s DSOs and MSOs use USB or LAN con-
nectivity. If you need to use your oscilloscope in an automated test environment, make
sure the oscilloscope you select has the required hardware connectivity ports and is fully
programmable. In other words, make sure any measurement that can be performed us-
ing the oscilloscope’s front panel and menu controls can also be programmed remotely.
Keysight’s InfiniiVision X-Series and Infiniium Series oscilloscopes are all fully program-
mable via SCPI commands as well as National Instruments IVI drivers.
When you perform manual oscilloscope measurements on the bench, it is often import-
ant to document/save test results. One method of documenting test results is to simply
send a screen image to a printer connected directly to the oscilloscope. But a more
common method of documenting test results today is to save data. In addition to being
able to transfer data to a PC via a direct USB or LAN connection, most of today’s digital
oscilloscopes have the ability to save images and waveform data in various formats
directly to a USB memory stick, as shown in Figure 28. Saved images (screen-shots) and
data (waveforms) can then be easily imported into various word processors, spread-
sheets, and applications such as MATLAB.
Keysight’s N8900A InfiniiView offline analysis software lets you easily capture waveforms
on your oscilloscope, save them to a file, and recall the waveforms into the application.
Figure 27. Automated test rack.

Figure 28. Quickly and easily save waveform data and screen-shots to you personal USB drive.
Some of today’s digital oscilloscopes even have built-in Web browsers. This makes it
easy for engineers around the globe to access “live” oscilloscope measurements that
may reside in another part of the world. For instance, Figure 29 shows an example of an
engineer in his office in the U.S.A. remotely controlling and making measurements on an
oscilloscope connected to a device-under-test in China.
Figure 29. Keysight’s InfiniiVision’s built-in Web browser with the virtual remote front-panel user interface makes
it easy to control and access “live” oscilloscope measurements from anywhere in the world.
Tip #10: Connectivity and documentation (continued)

Tip #11: Probing
Select an oscilloscope from a vendor that can
provide the variety of specialty probes you
may require
Your oscilloscope measurements can only be as good as what
your probe delivers to the oscilloscope’s BNC inputs. When you
connect any kind of measurement system to your circuit, the
instrument (and probe) becomes part of your device-under-test.
This means it can “load” or change the behavior of your signals
to some degree. Good probes should not disturb the input signal
and should ideally deliver an exact duplicate of the signal that
was present at the probe point before the probe was attached.
When you purchase a new oscilloscope, it typically comes stan-
dard with a set of high-impedance passive probes — one probe
for each input channel of the oscilloscope. These types of gener-
al-purpose passive probes are most common and enable you to
measure a broad range of signals relative to ground. But these
probes do have limitations. Figure 30 shows an electrical model
of a typical 10:1 passive probe connected to the high-impedance
input (1-MΩ input of an oscilloscope).
Figure 30. Typical model of a 10:1 passive probe.
Inherent in all oscilloscope probes and inputs are parasitic
capacitances. These include the probe cable capacitance (Ccable
),
as well as the oscilloscope’s input capacitance (Cscope
). “Inherent/
parasitic” simply means these elements of the electrical model
are not intentionally designed-in, but are just an unfortunate fact
of life in the real world of electronics. The amount of inherent/
parasitic capacitance will vary from oscilloscope-to-oscilloscope
and probe-to-probe. Also included in this electrical model are
designed-in capacitive elements that are used to compensate for
low-frequency pulse response.
The electrical model of any probe (passive or active) and os-
cilloscope can be simplified down to parallel combination of a
single resistor and single capacitor. Figure 31 shows a typical
oscilloscope/probe loading model for a 10:1 passive probe. This
is essentially what gets connected in parallel with your DUT
when making oscilloscope measurements with a probe. For
low frequency or DC applications, loading is dominated by the
10-MΩ resistance, which in most cases should not be a problem.
Although 13.5 pF may not sound like much capacitance, at higher
frequencies the amount of loading contributed by this capaci-
tance can be significant. For instance, at 500 MHz the reactance
of 13.5 pF in this model is just 23.6 Ω, which could contribute to
significant “loading” and signal distortion.
Figure 31. Simplified probe/oscilloscope electrical model.

For higher frequency measurement applications, active probes
should be used, such as Keysight’s InfiniiMode Series differential
active probe shown in Figure 32. “Active” means that the probe
consists of an amplifier near the probe’s tip. This can significantly
reduce the amount of capacitive loading and increase probing
bandwidth. But the tradeoff with high-frequency active probes is
often reduced dynamic range as well as price.
Figure 32. Keysight’s InfiniiMode Series differential active probe.
Besides high-frequency active probes, there are many other
specialty probing applications that should be considered. If you
need to make measurements on a high-speed differential serial
bus, then you should consider using a high-frequency differential
active probe. If you need to make measurements on very high
voltage signals, you should consider using a high-voltage probe.
If you need to make current measurements, you should consider
using a current probe.
To learn more about oscilloscope probing, refer to Keysight’s
application note Eight Hints for Better Scope Probing, which is
listed in the related literature section at the end of this document.
Keysight Technologies offers a broad range of passive, active,
differential, and current probes that will meet your particular
probing measurement needs. Refer to the Keysight probes data
sheets listed at the end of this document to learn more about
Keysight’s various probing solutions.
Tip #11: Probing (continued)

Tip #12: Ease-of-use
Select an oscilloscope that can improve your
measurement productivity with an intuitive us-
er-interface
Ease-of-use. Usability.
User-friendly. Intuitive. These
are important oscilloscope
characteristics. Although
we have addressed ease-of-
use last in our list of 12 tips,
sometimes the usability of
an oscilloscope can be just
as important as specified
performance characteristics,
such as bandwidth, sample
rate, and memory depth.
As oscilloscope vendors
have packed more and more
advanced features and capa-
bilities into today’s digital storage oscilloscopes, many engineers
believe oscilloscopes have become more difficult to use. Even if a
new oscilloscope has an advanced measurement capability that
is intended to improve measurement productivity, if the advanced
feature is too difficult to find because it is buried deep in a sub-
menu of the oscilloscope or if it is too difficult to set up because
it includes tons of advanced settings that the user doesn’t clearly
understand, then most engineers will simply grab the old oscillo-
scope off the shelf and perform the measurement the old way.
Although most oscilloscope vendors will claim that their oscillo-
scopes are the easiest to use, usability is not a specified param-
eter that you can compare against in a product’s data sheet.
Ease-of-use is subjective, and you must evaluate it for yourself.
Of course the easiest oscilloscope for you to use today is probably
the one that you are currently using. This is simply because you
are familiar with it and may be hesitant to change. This is human
nature, though it is worth looking into how vendors have improved
usability to make your job easier and faster.
The following are some important usability factors that we be-
lieve you should consider.
Knobs
Engineers like knobs on their oscilloscopes. Oscilloscopes should
have knobs that directly control all key variables including vertical
scaling (v/div), vertical position, timebase scaling (s/div), hori-
zontal position, and trigger level as shown in Figure 33. Some
oscilloscopes have multiplexed knobs, such as just one set of
vertical scaling knobs as opposed to scaling knobs for each input
channel. Some oscilloscopes also “bury” key variables such as
horizontal position and/or trigger level within menus.
Figure 33. Oscilloscope front panels should include knobs for all key setup
variables.

Responsiveness
Responsiveness is important. Setting up an oscilloscope is often
a random and iterative process. Turn this knob… turn that knob…
turn another knob until the waveform is properly scaled on the
screen. But if the oscilloscope is unresponsive because it’s busy
processing captured data from the previous acquisition, setting
up the oscilloscope can become a frustrating experience.
Built-in HELP
Turning on and using advanced features shouldn’t require an ad-
vanced degree. Engineers are reluctant to read manuals and us-
er’s guides, even if they could find them. Some oscilloscopes have
built-in HELP screens that provide short setup tips about specific
features. For example, on many Keysight oscilloscopes, you can
access built-in HELP by simply pressing and holding down any
front panel key or menu button. Figure 34 shows a Keysight Runt
Triggering HELP screen.
Figure 34. Built-in HELP screens assist users in setting up advanced
measurements.
Larger Color Displays
Today’s oscilloscopes can display lots of measurement
information besides just waveforms. Larger displays with color
can help clear the clutter so your eyes can focus on what’s most
important.
Keysight has found some innovative ways to use touch-screen
technology to improve oscilloscope usability, such as InfiniiScan
Zone triggering, which is available on the InfiniiVision 3000T,
4000 and 6000 X-Series. It uses the same capacitive-touch tech-
nology found in tablet computers on the market today. Simply
use your finger to draw a box around the waveform that you want
to trigger on, and the oscilloscope triggers on that unique signal
without the hassle of setting up a complex trigger condition
Figure 35. The 4000 X-Series oscilloscope’s touch screen and InfiniiScan Zone help
you quickly set up complex trigger conditions.
Tip #12: Ease-of-use (continued)

Related literature
Title Document type Publication number
Keysight InfiniiVision 2000 X-Series Oscilloscopes Data sheet 5990-6618EN
Keysight InfiniiVision 3000T X-Series Oscilloscopes Data sheet 5992-0140EN
Keysight Infiniium S-Series Oscilloscope Data sheet 5991-3904EN
InfiniiVision Oscilloscope Probes Accessories Data sheet 5968-8153EN
Infiniium Oscilloscope Probes and Accessories Data sheet 5968-7141EN
Serial Bus Options for InfiniiVision X-Series Oscilloscopes Data sheet 5990-6677EN
Evaluating Oscilloscope Bandwidths for your Applications Application note 5989-5733EN
Oscilloscope Sample Rates versus Sampling Fidelity Application note 5989-7885EN
Using Oscilloscope Segmented Memory for Serial Bus Applications Application note 5990-5817EN
Oscilloscope Waveform Update Rate Determines Probability of Capturing
Elusive Events
Application note 5989-7885EN
Synchronizing on Infrequent Anomalies and Complex Signals using InfiniiScan
Zone Trigger
Oscilloscope Display Quality Impacts Ability to View Subtle
Signal Details
Evaluating Oscilloscopes to Debug Mixed-Signal Designs Application note 5989-3702EN
Eight Hints for Better Scope Probing Application note 5989-7894EN
To download these documents, insert the publication number in the URL:
http://literature.cdn.keysight.com/litweb/pdf/xxxx-xxxxEN.pdf

InfiniiVision X-Series Oscilloscopes
Keysight’s mid-range performance InfiniiVision 2000, 3000, and
4000 X-Series oscilloscopes have been optimized for bench-
top debug and troubleshooting. These oscilloscopes come in
bandwidth models ranging from 70 MHz up to 1.5 GHz. With the
fastest waveform update rates in the industry (up to 1,000,000
waveforms per second), these oscilloscopes can capture and
display infrequent signal anomalies that other oscilloscopes miss.
Infiniium Series Oscilloscopes
Keysight’s higher-performance Infiniium S-Series and 90000
Series oscilloscopes are Windows-based instruments that have
been optimized for advanced waveform analysis. These oscillo-
scopes come in bandwidth models ranging from 500 MHz up to
63 GHz. The Infiniium Series oscilloscopes also have the deepest
available acquisition memory in the industry (up to 2 Gpts). Also
available on these oscilloscopes is a wide range of industry-stan-
dard compliance test packages, as well as advanced measure-
ment options such as jitter analysis.
Keysight Technologies Oscilloscopes
Multiple form factors from 20 MHz to 90 GHz | Industry-leading specs | Powerful applications
Keysight’s InfiniiVision and Infiniium Series Oscilloscopes

This information is subject to change without notice.
© Keysight Technologies, 2013 - 2014
Published in USA, November 26, 2014
5991-2714EN
www.keysight.com
myKeysight
www.keysight.com/find/mykeysight
A personalized view into the information most relevant to you.
Three-Year Warranty
www.keysight.com/find/ThreeYearWarranty
Keysight’s commitment to superior product quality and lower total cost
of ownership. The only test and measurement company with three-year
warranty standard on all instruments, worldwide.
Keysight Assurance Plans
www.keysight.com/find/AssurancePlans
Up to five years of protection and no budgetary surprises to ensure your
instruments are operating to specification so you can rely on accurate
measurements.
www.keysight.com/go/quality
Keysight Technologies, Inc.
DEKRA Certified ISO 9001:2008
Quality Management System
Keysight Channel Partners
www.keysight.com/find/channelpartners
Get the best of both worlds: Keysight’s measurement expertise and product
breadth, combined with channel partner convenience.
www.keysight.com/find/scopes
For more information on Keysight
Technologies’ products, applications or
services, please contact your local Keysight
office. The complete list is available at:
www.keysight.com/find/contactus
Americas
Canada (877) 894 4414
Brazil 55 11 3351 7010
Mexico 001 800 254 2440
United States (800) 829 4444
Asia Pacific
Australia 1 800 629 485
China 800 810 0189
Hong Kong 800 938 693
India 1 800 112 929
Japan 0120 (421) 345
Korea 080 769 0800
Malaysia 1 800 888 848
Singapore 1 800 375 8100
Taiwan 0800 047 866
Other AP Countries (65) 6375 8100
Europe Middle East
Austria 0800 001122
Belgium 0800 58580
Finland 0800 523252
France 0805 980333
Germany 0800 6270999
Ireland 1800 832700
Israel 1 809 343051
Italy 800 599100
Luxembourg +32 800 58580
Netherlands 0800 0233200
Russia 8800 5009286
Spain 800 000154
Sweden 0200 882255
Switzerland 0800 805353
Opt. 1 (DE)
Opt. 2 (FR)
Opt. 3 (IT)
United Kingdom 0800 0260637
For other unlisted countries:
www.keysight.com/find/contactus
(BP-09-23-14)

How to Select Your Next Oscilloscope

More Related Content

What's hot (20)

Similar to How to Select Your Next Oscilloscope (20)

Recently uploaded (20)

How to Select Your Next Oscilloscope