IRJET- Morphometric Analysis of Sina Basin Using GIS and Remote Sensing Techniques

International Research Journal of Engineering and Technology (IRJET) e-ISSN: 2395-0056
Volume: 06 Issue: 4 | Apr 2019 www.irjet.net p-ISSN: 2395-0072
© 2019, IRJET | Impact Factor value: 7.211 | ISO 9001:2008 Certified Journal | Page 5212
Morphometric Analysis of Sina Basin using GIS and Remote Sensing
Techniques
Akash M. Pandule
Sahyadri College of Agricultural Engineering, Yeshwantnagar, Karad, Maharashtra, India.
----------------------------------------------------------------------------------------------------------------------------------------------------
Abstract: Geographical Information system (GIS) and Remote Sensing has become an efficient tool in
this present era for the delineation of drainage pattern and water resource management. Sina river
basin up to Sina dam of Nimgaon Gangurda in Ahmednagar district of Maharastra is considered for the
present study. The basin has about 1484 km2 catchment area. The Cartosat DEM (Digital Elevation
Model) with 32 m x 32 m resolution is used for the morphometric analysis of the basin to derive
linear, areal and relief aspects by using the ArcGIS 10.3. Survey Of India (SOI) toposheet number
E43I13 having 1: 50,000 scale is used for the study. Strahler’s stream order was followed for the
further analysis. The drainage pattern of Sina river basin is dendritic type with 6th order trunk stream
having mean bifurcation ratio 5.798, main channel length 77.9 km and Channel index is 1.42. The areal
aspect such as Elongation ratio, Circulatory ratio, Stream frequency, Drainage density and Length of
overland flow (Km) is found to be 0.69, 0.4, 4.283, 2.49 and 0.2, respectively. The relief aspect such as
Ruggedness number, Total contour length (Km) and average slope (%) is 0.986, 9305.842, and 1.422,
respectively. Sina basin has very fine texture, elongated in shape, dendric drainage nature and eroded
watershed which need protection.
Keywords: GIS, Remote Sensing, Morphometric analysis, Cartosat DEM
INTRODUCTION
Morphometry is nothing but the mathematical analysis and measurement of configurations of
earths shape, surface and dimension of landforms. Morphometric properties gives important
information’s related with the formation & development of hydrologic & geographic properties of
watershed. Morphometric analysis also gives a quantitative description of drainage system, as
drainage system is important for characterisation of watershed. Morphometric analysis is also
important in order to investigate the pedology, environmental assessment, groundwater management
& groundwater potential. It also checks the relief, areal aspect, geometric and linear aspect gives
hierarchial order of streams along with number and length of stream segment etc. The areal aspect
gives the analysis of basin shape, basin parameter both geometrical and topological (Stream
frequency, Drainage density). The relief aspects include dissection index, absolute and relative relief
and average slope. Morphometric parameter generally depends upon bed rock, lithology, pedology

and geological structures. Hence, the information related with the geomorphology, hydrology,
geology, and land use pattern is highly important for doing trusted study of drainage pattern of the
watershed. For quantitative analysis of the watershed involving various components such as stream
segments, stream order , basin perimeter & area, elevation difference, slope and profile of land has
majorly responsible for the natural development of basin (Horton, 1945). As the first and majorly
important work on basin morphometry analysis was carried out by Horton (1932, 1945). Then,
Horton’s study in various ways modified and developed by several Geomorphologist and
Geohydrologist, which was mainly Strahler (1953), Schumm (1956), Melton (1957), Morisawa (1957),
Strahler (1957), Gregory and Walling (1973), Chorley et al. (1984). In recent decades, the
morphometric analysis of the various River basins, have been done by many researchers and scientist
( Esper, 2008; Magesh et al., 2011; Bhagwat et al., 2011; Wilson et al., 2012; Singh et al., 2014; Sujatha
et al., 2014; Gaikwad and Bhagat (2017) have studied morphometric parameters for watershed
prioritization . In this study an attempt has made to understand the morphometric characteristics of
Sina river basin which helps to understand the basin area, topographic relation, agriculture,
forestation and regional planning.
STUDY AREA
Sina River makes the boundary between Ahmednagar district on one side and other side Ashti
Tahsil of Beed district. Sina river is the major left tributary of Bhima river. Sina dam is an earthfill dam
on Sina river at Nimgaon Gangurda in Karjat taluka of Ahmednagar district of Maharashtra is
considered as an outlet for this study. The latitude and longitudinal coordinates of Sina dam are
18049’39.15’’N, 74056’52.17’’E and corresponding elevation is 579 m above mean sea level. Sina river
is starting near Ahmednagar city as it has two main sources one near Jeur about 16 km to its north-
east and one near Jamgaon about 20 km west of Ahmednagar city. The study area of Sina river basin is
taken about 1484 km2. The latitudinal and longitudinal extent of the Sina river basin under study lies
between 18.736 to 19.26 N and 74.482 to 74.948 E. The study area lies in scarcity areas as the annual
average rainfall is about 546 mm (Musande, et al, 2003). The soil type of this area is medium to fine
textured and available water content was 205 mm/m depth and depth 85% soils in category of
moderate deep to very deep. Average rainfall occurs in month of June and highest rainfall occurs in
July and September (Musande et al 2003). Crops cultivated in this area are pearl millet, black gram,
red gram, green gram, sorghum, pigeon pea, sunflower etc.

Figure 1. Location map of study area
Data Used and Methodology
In this study of morphometric analysis of Sina river basin remote sensing and GIS (Geographic
Information System) technique was used. The remotely sensed data rectified by using the Survey of
India (SOI) topographical maps of about 1: 50,000 and analysed by using ArcGIS 10.3 by using DEM
(Digital Elevation Model) and toposheet. Topographical map: SOI (Scale 1: 50,000) Number E43I13;
Cartosat (DEM) with 32 m x 32 m spatial resolution. SOI topographic map is georeferenced using
WGS-1984 datum, Universal Transverse Mercator (UTM) zone 43N projection in ArcGIS 10.3. In this
study the Strahlers law is used for giving the stream order to the branch by considering first
unbranched stream as first order stream then next when two first order streams join together then it
is designated as second order. When second order stream joins together to form third order and so on
then number of streams are counted and recorded.

RESULT AND DISCUSSION
Linear aspect
The liner aspects of drainage network such as Stream Orders (Sμ), Stream Number (Nμ),
bifurcation ratio (Rb), Stream Length (Lu), Mean Stream Length (Lum) and Stream Length Ratio (Lur)
Stream order (Su)
Stream order designation is the first step in morphometric analysis of drainage basin
depending on hierarchy (Strahler, 1952). It was found that the Sina river basin is a 6th order trunk
stream. It is found that the maximum stream order frequency of the Sina river is observed in case of
first-order streams and then for second order and then decreses upto last highest order stream.
Figure 2. Stream Order of Sina Basin
Stream Number (Nu)
The summation of order wise stream segments is known as stream number. Stream number is
an inverse of stream order. Stream numbers of 1st, 2nd, 3rd, 4th, 5th, 6th streams are 5001, 1098, 204, 42,
10 and 1 respectively. As the basin has 1st order stream has more number of stream number so it is
responsible for sudden removal of water after heavy rainfall.
Stream length (Lu)
Total stream lengths calculated by using SOI topographical sheets and ArcGIS software. In
Hortons law the Geometric similarity preserved in watershed of increasing order (Strahler, 1964).
Mean Stream Length (Lum)

Mean stream length (Lum) is related to drainage network components and contributing
watershed surface (Strahler, 1964). It is calculated by dividing the total length of stream of an order
by total number of segments in the order.
Stream Length Ratio (Lurm)
Horton (1945) calculated the length ratio by dividing the man length of segment (Lu) of order
to mean length of segments of next lower order (Lu-1) which is constant throughout the successive
orders of basin. When stream length ratio increase from lower order to higher order indicates mature
geographic stage of basin.
Bifurcation ratio (Rb)
Bifurcation ratio is calculated by dividing the number of stream segments of given order (Nu)
to the number of streams in the next higher order (Nu+1). Bifurcation ratio is an index of relief and
dissertation. Bifurcation ratio is a dimensionless property. Lower values (<5) of bifurcation ratio
indicate that watershed has less structural disturbances (Strahler, 1964) and drainage pattern has
been not distorting (Nag 1998). A higher value (>5) of bifurcation ratio indicates that strong
structural control on the drainage pattern and the lower values indicates that watershed is not
affected by structural disturbance. The results shows that bifurcation ratio is found 5.798 shows
drainage pattern is controlled by geological structure.
Weighted mean Bifurcation ratio (Rbwm)
Strahler (1953) used a weighted mean bifurcation ratio in order to arrive at a more
representative bifurcation ratio by multiplying the bifurcation ratio of each successive pair of orders
by toatal number of streams in this ratio and then calculated the mean of sum of these values. The
obtained value of Rbwm for this is 4.71.
Length of main channel (Cl)
Length of main channel (Cl) is the length along the longest watercourse from outflow point of
watershed to the uppermost watershed boundary. The length of main channel (Cl) is computed by
using ArcGIS 10.3 software, which is 77.9 km.
Channel Index (Ci) & Valley Index (Vi)
For the measurement of valley length, channel length and shortest distance between the mouth
and source of river (Adm). Adm is used for the computation of Channel index and valley index. The
calculated Channel Index (Ci) & Valley Index (Vi) is found to be 1.42 and 1.35 respectively.
RHO coefficient

RHO coefficient is calculated by dividing the stream length ratio to the bifurcation ratio. The
relation between the drainage density and physiographic development of basin is determined by RHO
coefficient (Horton, 1945). RHO coefficient is influenced by factors like climatic, biologic,
anthropogenic and geomorphologic factors. The calculated value of RHO coefficient for this study area
is 0.58.
Table 1: Stream Order, Streams Number, and Bifurcation Ratios in Sina river basin
Su Nu Rb Nu-r Rb*Nu-r Rbwm
I 5001 - - -
II 1098 4.55 6099 27750.45
III 204 5.38 1302 7004.76 4.71
IV 42 4.86 246 1195.56
V 10 4.2 52 218.4
VI 1 10 11 121
Total 6353 28.99 7710 36290.17
Mean Rbm= 5.798
Su: Stream order, Nu: Number of streams, Rb: Bifurcation ratios, Rbm: Mean bifurcation
Ratio*, Nu-r: Number of stream used in the ratio, Rbwm: Weighted mean bifurcation ratios
Table 2: Stream Length and Stream Length Ratio in Sina river basin
Su Lu Lu/Su Lur Lur-r Lur*Lur-r Luwm
I 2035 0.41 - - -
II 837 0.76 1.85 2872 5313.2
III 405 0.5 0.66 1242 819.72
IV 254 1.99 3.98 659 2622.82 2.199
V 117 11.7 5.88 371 2181.48
VI 52 52 4.44 169 750.36
Total 3700 67.36 16.81 5313 11687.58
Mean Lurm=3.362
Su: Stream order, Lu: Stream length, Lur: Stream length ratio, Lurm: Mean stream length
ratio*, Lur-r: Stream length used in the ratio, Luwm: Weighted mean stream length ratio
Table 3: Linear aspect of Sina river basin
Sr.
No
Morphometric
parameter
Formula Reference Result
1 Stream Order (Su) Hierarchical Rank Strahler (1952) 1 to 6
2 1st Order Stream (Suf) Suf = N1 Strahler (1952) 5001
3 Stream Number (Nu = N1+N2+ …Nn Horton (1945) 6356
4 Stream Length (Lu) Kms Lu = L1+L2 …… Ln Strahler (1964) 3700
5 Stream Length Ratio
(Lur)
see Table 2 Strahler (1964) 0.66-5.88
6 Mean Stream Length
Ratio (Lurm)
see Table 2 Horton (1945) 3.362

7 Weighted Mean Stream
Length Ratio (Luwm)
see Table 2 Horton (1945) 2.199
8 Bifurcation Ratio (Rb) see Table1 Strahler (1964) 4.2-10
9 Mean Bifurcation Ratio
(Rbm)
see Table1 Strahler (1964) 5.798
10 Weighted Mean
Bifurcation Ratio (Rbwm)
see Table1 Strahler (1953) 4.71
11 Main Channel Length (Cl)
Kms
GIS Software
Analysis
- 77.9
12 Valley Length (Vl) Kms GIS Software
Analysis
- 74.31
13 Minimum Aerial Distance
(Adm) Kms
GIS Software
Analysis
- 54.92
14 Channel Index (Ci) Ci = Cl / Adm (H &
TS)
Miller (1968) 1.42
15 Valley Index (Vi) Vi = Vl / Adm (TS) Miller (1968) 1.35
16 Rho Coefficient (ρ) ρ = Lur / Rb Horton (1945) 0.58
Areal aspect
The areal aspect of the drainage basin (watershed) such as Drainage density (Dd), Stream
frequency (Fs), Drainage Texture (Rt), Form Factor (RF), Elongation ratio (Re), Circularity ratio (Rc),
Length of overland flow (Lg), Constant of channel maintenance (C), Lemniscate (k), Infiltration
Number (If), Basin perimeter (P) were calculated and result shown in Table 4.
Length of basin (Lb)
Basin length is the longest dimension of basin parallel to principal drainage line (Schumm,
1956). It is calculated according to Schumm (1956) as it is found to be 62.8 km.
Basin area (A)
Area has the same importance like other parameter that is the total stream length. The basin
area is computed by using the ArcGIS 10.3 software, which is 1484 km2.
Basin Perimeter (P)
The outermost boundary of basin that enclosed the area called the basin perimeter. Basin
perimeter is an indicator of watershed size and shape. The basin perimeter is computed by using the
ArcGIS 10.3 software, which is found to be 222m.
Length area relation (Lar)
Lar = 1.4* A0.6 formula proposed by Hack (1957) gives the relation between the stream length
and basin area.

Lemniscate’s (k)
For the determination of the slope of basin Chorely (1967) gives a Lemniscate’s value. It is determined
by using the formula k= Lb2/4*A where Lb is basin length in km and A is the area of basin in km2. The
computed value of k is found to be 2.66.
Form factor (Ff)
Form factor is also known as an index as it is dimensionless form used to represent the
different basin shapes (Horton, 1932). Form factor varies between 0.1 to 0.8. Higher value of form
factor indicates basin is circular type while the smaller value indicates enlongated basin. The range of
form factor for elongated basin is <0.78 and for circular is >0.78. In case of Sina river basin the form
factor value is 0.38 which indicates basin is elongated.
Elongation ratio (Re)
Elongation ratio is defined as the ratio of diameter of a circle of the same area as the basin to
maximum basin length (Schumm, 1956). According to Strahler states that elongation ratio varies
between 0.6 to 1.0 over a wide variety of climatic and geologic types. The slope of watershed is
classified with the help of elongation ratio, i.e elongated (0.5-0.7), less elongated (0.7-0.8), oval (0.8-
0.9), circular (0.9-0.10). The elongated ratio of Sina river basin is 0.69, which represents that the basin
is elongated.
Texture ratio (Rt)
Texture ratio is ratio between the first order streams and perimeter of basin (Rt= NI/P) and its
depends on lithology, relief aspects of terrain and infiltration capacity. Texture ratio is an important
parameter in order to morphometric analysis as it depends on infiltration capacity, relief aspects of
terrain and lithology. The texture ratio of this basin was found to be 22.527.
Circulatory ratio (Rc)
Circularity ratio is dimensionless property and express as the degree of circulatory of the
entire basin. Circularity value varies between 0 to 1 but value closes to 1. Circulatory ratio is
calculated by dividing the watershed area to the area of a circle having the same perimeter as that the
watershed. According to Miller (1953) the circulatory ratio of basin varies from 0.4 to 0.6 which
indicates the basin is elongated and highly permeable geological materials. The circulatory ratio of
basin is found to be 0.4 which indicates that the basin is elongated type.
Drainage texture (Dt)

Drainage texture is calculated by dividing the stream segments of all orders to the perimeter of
that area (Horton, 1945). The five drainage texture classification given by the Smith (1950) i.e., very
fine (>8), fine (6 to 8), moderate (4 to 6), coarse (2 to 4), very coarse (<2). The drainage texture of
basin is calculated to be 28.63 indicates that the texture is very fine.
Compactness coefficient (Cc)
Compactness coefficient (Cc) is calculated by dividing the perimeter of watershed to
circumference of circular area, which is equal to the area of watershed (Gravelius 1994). Compactness
coefficient depends only on the slope but not on the size of watershed. The Cc of given basin was
found to be 1.21.
Fitness ratio (Rf)
Fitness ratio is the ratio of the main channel length to the length of watershed perimeter.
Fitness ratio is a measure of topographic fitness (Melton 1957). The fitness ratio for Sina basin is 0.35.
Wandering ratio (Rw)
The ratio of main stream length to the valley length is known as wandering ratio (Rw) (Smart &
Surkan 1967). The straight line distance between outlet of basin and remost point on the ridge is
called the valley length. In this study wandering ratio is found to be 1.24.
Watershed Eccentricity (τ)
The expression for watershed eccentricity, which is: τ = [(|Lcm2 -Wcm2|)] 0.5 / Wcm Where: τ
= Watershed eccentricity, Lcm = Straight length from the watershed mouth to the centre of mass of
the watershed, and Wcm = Width of the watershed at the centre of mass and perpendicular to Lcm.
The watershed eccentricity is a dimensionless property. For the given watershed the watershed
eccentricity, is computed to be 0.42.
Centre of Gravity of watershed (Gc)
Centre of Gravity of watershed (Gc) is calculated by measuring the length from the outlet of
watershed to a point on stream nearest to the center of of watershed. The centre of gravity of
watershed calculated by using the ArcGIS-10.3 software, which is latitude 18.99N and longitudes
74.75E.
Sinuosity Index (Si)
The pattern of channel of a drainage basin is equal to sinusity. The ratio of channel length to
down valley distance is sinuosity. Sinusity value varies between 1 to 4 and more. Sinuosity index is

generally used for the Geomorphologists, Hydrologists and Geologists. The computed hydraulic,
topographic and standard sinuosity index which are 16.66%, 83.33%, and 1.05 respectively.
Stream frequency (Fs)
The number of stream segment per unit area is called stream frequency. Stream frequency also
known as channel frequency (Horton 1932). The stream frequency of watershed found to be 4.283.
Drainage Density (Dd)
The stream length per unit area in region of watershed is called drainage density (Horton,
1952). The drainage density calculated by using spatial analyst tool in ArcGIS-10.3. The range for Dd
are vary as very coarse (<2), coarse (2-4), moderate (4-6), fine (6-8) and very fine (>8). The basin has
Dd found to be 2.49 which indicates coarse drainage basin.
Infiltration Number (If)
Infiltration number is the product of drainage density (Dd) and stream frequency (Fs) i.e. If=
Dd*Fs. Higher value of infiltration number means lower the infiltration capacity and higher runoff
(Horton1964). The infiltration number (If) is found to be 10.66 for the basin which indicates basin has
lower value of infiltration capacity and higher runoff.
Drainage pattern (Dp)
Drainage pattern (Dp) helps in identifying the stage of erosion. In drainage pattern influence of
slope, lithology and structure reflects. The study area has dendritic and radial pattern. Howard (1967)
related drainage patterns to geological information’s.
Length of Overland flow (Lg)
Length of Overland flow (Lg) is equal to the half the reciprocal of drainage density. Higher the
value of length of overland flow indicates lower relief and vice versa. The range for the values of
length of overland flow are in three classes as low value (<0.2), moderate value (0.2-0.3) and high
value (>0.3). Lower value indicates high relief, more runoff and less infiltration where as higher value
of Lg gives gentle slope, more infiltration and reduced runoff. Length of Overland flow (Lg) is
computed to be 0.2 means it has moderate to high relief, runoff and less infiltration.
Constant of Channel Maintenance (C)
Constant of Channel Maintenance (C=1/Dd) is the inverse of drainage density. Constant
channel maintenance of watershed is computed to be 0.4.

Table 4: Areal aspect of Sina river basin
Sr.No Morphometric
parameter
1. Length from W’s
Center to Mouth of
W’s (Lcm) Kms
GIS Software Analysis Black (1972) 27.74
2. Width of W’s at the
Center of Mass
(Wcm) Kms
3. Basin Length (Lb)
Kms
4. Mean Basin Width
(Wb)
Wb = A / Lb Horton (1932) 23.63
5. Basin Area (A) Sq
Kms
GIS Software Analysis Schumm(1956) 1484
6. Basin Perimeter (P)
Kms
GIS Software Analysis Schumm(1956
)
222
7. Relative Perimeter
(Pr )
Pr = A / P Schumm(1956
)
6.68
8. Length Area
Relation (Lar)
Lar = 1.4 * A0.6 Hack (1957) 111.94
9. Lemniscate’s (k ) k = Lb2 / A Chorley (1957) 2.66
10. Form Factor Ratio
(Rf)
Ff = A / Lb2 Horton (1932) 0.38
11. Shape Factor Ratio
(Rs)
Sf = Lb2 / A Horton (1956) 2.66
12. Elongation Ratio
(Re)
Re = 2 / Lb * (A / π) 0.5 Schumm(1956
)
0.69
13. Elipticity Index (Ie) Ie = π * Vl2 / 4 A 2.92
14. Texture Ratio (Rt) Rt = N1 / P Schumm(1965
)
22.527
15. Circularity Ratio
(Rc)
Rc = 12.57 * (A / P2) Miller (1953) 0.4
16. Circularity Ration
(Rcn)
Rcn = A / P Strahler (1964) 6.68
17. Drainage Texture
(Dt)
Dt = Nu / P Horton (1945) 28.63
18. Compactness
Coefficient (Cc)
Cc = 0.2841 * P / A 0.5 Gravelius
(1914)
1.64
19. Fitness Ratio (Rf) Rf = Cl / P Melton (1957) 0.35
20. Wandering Ratio
(Rw)
Rw = Cl / Lb Smart &
Surkan (1967)
1.24
21. Watershed
Eccentricity (τ)
τ =
[(|Lcm2Wcm2|)]0.5/Wcm
Black (1972) 0.42
22. Centre of Gravity of GIS Software Analysis Rao (1998) 74.75E &

the Watershed (Gc) 18.99N
23. Hydraulic Sinuosity
Index (Hsi) %
Hsi = ((Ci - Vi)/(Ci -
1))*100
Mueller (1968) 16.66
24. Topographic
Sinuosity Index (Tsi)
%
Tsi = ((Vi - 1)/(Ci-
1))*100
Mueller (1968) 83.33
25. Standard Sinuosity
Index (Ssi)
Ssi = Ci / Vi Mueller (1968) 1.05
26. Longest Dimension
Parallel to the
Principal Drainage
Line (Clp) Kms
GIS Software Analysis - 74.707
27. Stream Frequency
(Fs)
Fs = Nu / A Horton (1932) 4.283
28. Drainage Density
(Dd) Km / Kms2
Dd = Lu / A Horton (1932) 2.49
29. Constant of Channel
Maintenance (Kms2
/ Km)
C = 1 / Dd Schumm(1956) 0.4
30. Drainage Intensity
(Di)
Di = Fs / Dd Faniran (1968) 1.72
31. Infiltration Number
(If)
If = Fs * Dd Faniran (1968) 10.66
32. Drainage Pattern
(Dp)
Horton (1932) Dn & Ra
33. Length of Overland
Flow (Lg) Kms
Lg = A / 2 * Lu Horton (1945) 0.2
Relief aspect
Relief refers to the relative height of points on surface and lines with respect to the horizontal
base of reference. Relief expresses the magnitude of the vertical dimension of the landform.
Maximum basin relief (H)
Maximum basin relief (H) is the elevation difference between the highest Point in the
catchment and the catchment outlet. The basin relief is found to be 396m reveals that basin has
undulating terrain having high kinetic energy of water results in severe soil erosion.
Relief ratio (Rhl)
The elevation difference between the highest point and lowest point of watershed on the valley
floor is the total relief of river basin. The ratio between the total relief of basin and the longest
dimension of basin parallel to main drainage line is relief ratio (Schumm, 1956). In this study area of
river basin relief ratio found to be 0.0063.
Relative relief (Rhp)

Relative relief is calculated by using the formula given by the Melton (1957) is Rhp= H*100/P,
where P is perimeter in meter & H is total basin relief.
4.3.4 Absolute relief (Ra)
Absolute relief is the difference between the given location and the sea level. The absolute
relief is calculated by using ArcGIS-10.3 and which is found to be 898 m.
Channel gradient (Cg)
Channel Gradient (Cg) m / Kms is calculated by using the formula given by the Broscoe (1959)
is Cg = H / {(π/2) * Clp} where H is total basin relief an Clp is the longest dimension parallel to the
Principal drainage line (Clp) Kms. The channel gradient for the study area is found to be 3.37.
Ruggedness Number (Rn)
The surface unevenness or roughness is measured by the ruggedness number (Rn). The
product of basin relief and drainage density is the ruggedness number (Strahler, 1968). Ruggedness
number is usually combines the slope steepness along with the length. The ruggedness number for the
study area is 0.986.
Melton Ruggedness number (MRn)
The slope index that gives special representation of the relief ruggedness within the watershed
is called the Melton Ruggedness number (MRn).The study area has the MRn is 10.28.
Gradient ratio (Rg)
The indicator of the channel slope wich enables the assessment of of runoff volume (Sreedevi,
2004). The Rg for the study area is 0.0061.
Gradient & channel slope (Sgc)
The steepness of slope is the gradient expressed as a variation between its vertical intervals
(Vei) reduced to unity and its horizontal equivalent (Hoe). Gradient is calculated by using the formula
Sgc= Vei/Hoe.
Slope analysis (Sa)
Slope analysis (Sa) is calculated by using ArcGIS-10.3. It is the average slope in the degree. It is
found to be 0.01422 for the study area.
Average slope of overall basin (S)
Erodibility of watershed studied by using the average slope (Wenthworth 1930). When slope
percentage is more then erosion is more. The slope of watershed computed by using the formula S =
(Z * (Ctl/H)) / (10 * A) and is found to be 1.422%.
Mean slope of overall basin (Ѳs)

Mean slope of basin computed by using the formula Ѳs = (Ctl * Cin) /A where Ѳs = Mean slope
of oveall basin, Ctl= Total length of contour in watershed, A= area of the watershed, Cin=Contour
interval. The computed value of mean slope of Sina river basin is 0.063.
Hypsometric analysis (Hs)
The value of integral and the form of hypsometric curve both are important elements in the
topographic form. It shows the variation in regions differ in geologic structure and the stage of
development. The starting of hypsometric curve is large and it decreases at the stage of maturity and
old age (Strahler, 1952).
Table 5: Hypsometric data of Sina river basin
Sr.No. Altitude Range(m) Height(m)h Area(kms2)a h/H1 a/A2
1 >800 298 9 1 0.0098
2 800-700 198 104 0.66 0.114
3 700-600 98 799 0.32 0.88
4 600-502 0 912 0 1
A2= 912 km2
Table 6: Relief aspect of Sina river basin
Sr.No Morphometric
parameter
1. Height of Basin
Mouth (z) m
GIS Analysis / DEM - 502
2. Maximum Height of
the Basin (Z) m
GIS Analysis / DEM - 898
3. Total Basin Relief (H)
m
H = Z - z Strahler (1952) 396
4. Relief Ratio (Rhl) Rhl = H / Lb Schumm(1956
)
0.0063
5. Absolute Relief (Ra)
m
GIS Software
Analysis
898
6. Relative Relief Ratio
(Rhp)
Rhp = H * 100 / P Melton (1957) 0.178
7. Dissection Index
(Dis)
Dis = H / Ra Singh & Dubey
(1994)
0.44
8. Channel Gradient
(Cg) m / Kms
Cg = H / {(π/2) *
Clp}
Broscoe (1959) 3.37
9. Gradient Ratio (Rg) Rg = (Z - z) / Lb Sreedevi
(2004)
0.0061
10. Watershed Slope
(Sw)
Sw = H / Lb 0.0063
11. Ruggedness Number
(Rn)
Rn = Dd * (H /
1000)
Patton & Baker
(1976)
0.986

12. Melton Ruggedness
Number (MRn)
MRn = H / A0.5 Melton (1965) 10.28
13. Total Contour Length
(Ctl) Kms
GIS Software
Analysis
- 9305.842
14. Contour Interval
(Cin) m
GIS Software
Analysis
10m
15. Slope Analysis (Sa) GIS Analysis / DEM Rich (1916) 0.01422
16. Average Slope (S) % S = (Z * (Ctl/H)) /
(10 * A)
Wenthworth’s
(1930)
1.422
17. Mean Slope of Overall
Basin (Ѳs)
Ѳs = (Ctl * Cin) /A Chorley (1979) 0.063
18. Relative Height (h/H) see Table 5 (h/H ) Strahler (1952) 1 to 0
19. Relative Area (a/A) see Table 5 (a/A ) Strahler (1952) 0 to 1
20. Surface Area of Relief
(Rsa) Sq Kms
Composite Profile Brown (1952) 1484
21. Composite Profile
area (Acp) sq.km.
Area between the
Composite curve
and horizontal line
Pareta (2004) 1484
Conclusion
The present study conclude that Cartosat -DEM and GIS based evaluation of drainage
morphometric parameters and their influence on landforms, soils and eroded land characteristics. The
prioritization of watershed based on the linear aspect (La), Areal aspect (Aa), Relief aspect (Ra).
Length ratio, bifurcation ratio and stream order of basin indicates that the basin is sixth order basin
with dendritic type of drainage pattern. Higher first order stream results in easily disposal of water
hence the groundwater recharge is less. Form factor, Elongation ratio and Circulatory ratio shows the
basin type is elongated. Drainage texture shows that the basin texture is very fine that implies it has
more risk of soil erosion and infiltration ratio indicates basin has lower infiltration capacity and
higher runoff. From the maximum basin relief the terrain is undulating type having kinetic energy of
water is high results higher runoff.
Acknowledgement
I extend my gratitude to Sahyadri College of Agricultural Engineering Yeshwantnagar Karad,
Satara for providing the opportunity to prepare this research work. I thankful to JD INFOTECH,
Aurangabad, Maharashtra for providing Technical Assistance during INPLANT Training program. I
also thankful to Dr. S. H. Jedhe Training Co-ordinator, JD INFOTECH, Aurangabad suggestions.

REFERENCES
Alexander, P.O (1979), "Age and Duration of Deccan Volcanism: K. Ar. Evidence", Deccan Volcanism
Geological Society of India, Memoir No. 3, Bangalore, pp 244-257.
Bhagwat, T. N., Shetty, A., and Hegde, V. S., 2011. Spatial variation in drainage characteristics and
geomorphic instantaneous unit hydrograph (GIUH); implications for watershed management-A
case study of the Varada River basin, Northern Karnataka. Catena, 87(1), 52-59. DOI:
10.1016/j.catena.2011.05.007
Broscoe, A.J (1959), “Quantitative Analysis of Longitudinal Stream Profiles of Small Watersheds”,
Project N. 389-042, Tech. Bep. 18, Geology Department, Columbian University, ONR, Geography
Branch, New York.
Calef, W. C (1950), “Form and Process, Cambridge University Press”, London, pp 473.
Catchment”, International Association of Scientific Hydrology - Bulletin, 13, pp 61-68.
Chorley, R. J., Schumm, S. A. and Sugden, D. E., 1984. Geomorphology: London. Methuen and Co. London.
Chorley, R.J (1972), “Spatial Analysis in Geomorphology”, Mathuen and Co. Ltd., London.
Chorley, R.L (1967), “Models in Geomorphology”, in R.J. Chorley and P. Haggett (eds.), Models in
Geography, London, pp 59-96.
Dury, G.H (1952), “Methods of Cartographical Analysis in Geomorphological Research”, Silver Jubilee
Volume, Indian Geographical Society, Madras, pp 136-139.
Esper Angillieri, M. Y., 2008. Morphometric analysis of Colangüil river basin and flash flood hazard,
San Juan, Argentina. Environmental Geology, 55(1), 107-111. DOI: 10.1007/s00254-007-0969-
2
Faniran, A (1968), “The Index of Drainage Intensity - A Provisional New Drainage Factor”, Australian
Journal of Science, 31, pp 328-330.
Gaikwad, R. and Bhagat, V., 2017. Multi-Criteria Watershed Prioritization of Kas Basin in Maharashtra
India: AHP and Influence Approaches. Hydrospatial Analysis, 1(1), 41-61. DOI:
10.21523/gcj3.17010105
Gold, D. P (1980), “Structural Geology”, Chapter 14 in Remote Sensing in Geology, edit by Siegal, B. S.
and Gillespie, A. R., John Wiley, New York, pp 410-483.
Gregory, K. J., and Walling, D. E., 1976. Drainage basin form and process: A geomorphological approach.
Edward Arnold, London
Gregory, K.J. & Walling, D.E (1968), “The Variation of Drainage Density within a
Horton, R.E (1932), “Drainage Basin Characteristics”, Transactions, American Geophysical Union, 13,
pp 350-61.
Horton, R.E (1945), “Erosional Development of Streams and their Drainage Basins”,Bulletin of the
Geological Society of America, 56, pp-275-370.
King, C.A.M (1966), “Techniques in Geomorphology”, Edward Arnold, (Publishers)Ltd. London, pp
319-321.
Magesh, N. S., Chandrasekar, N., and Soundranayagam, J. P., 2011. Morphometric evaluation of
Papanasam and Manimuthar watersheds, parts of Western Ghats, Tirunelveli district, Tamil

Nadu, India: a GIS approach. Environmental Earth Sciences, 64(2), 373-381. DOI:
10.1007/s12665-010-0860-4
Melton, M.A., An analysis of the relations among elements of climate, Surface properties and
geomorphology, Project NR 389042, Tech. Rep. 11, Columbia University,1957.
Pareta, K (2003), “Morphometric Analysis of Dhasan River Basin, India”, UttarBharat Bhoogol Patrika,
Gorakhpur, 39, pp 15-35.
Pareta, K (2004), “Hydro-Geomorphology of Sagar District (M.P.): A Study through Remote Sensing
Technique”, Proceeding in XIX M. P. Young Scientist Congress, Madhya Pradesh Council of
Science & Technology (MAPCOST), Bhopal.
Pareta, K (2005), “Rainfall-Runoff Modelling, Soil Erosion Modelling, Water Balance Calculation, and
Morphometric Analysis of Molali Watershed, Sagar, Madhya Pradesh using GIS and Remote
Sensing Techniques”, proceeding in 25th International Cartographic Congress, INCA.
Pareta, K (2011), “Geo-Environmental and Geo-Hydrological Study of Rajghat Dam, Sagar (Madhya
Pradesh) using Remote Sensing Techniques”, International Journal of Scientific & Engineering
Research, 2(8) (ISSN 2229-5518), pp 1-8.
Pareta, K. and Koshta, Upasana (2009), “Soil Erosion Modeling using Remote Sensing and GIS: A Case
Study of Mohand Watershed, Haridwar”, Madhya Bharti Journal, Dr. Hari Singh Gour
University, Sagar (M.P.), 55, pp 23-33.
Rai, P. K., Mohan, K., Mishra, S., Ahmad, A. and Mishra, V. N., 2017. A GIS-based approach in drainage
morphometric analysis of Kanhar River Basin, India. Applied Water Science, 7(1), 217-232. DOI:
10.1007/s13201-014-0238-y
Richards, K.S. Arnett, R.R. and Ellis, J (1985), “Geomorphology and Soils”, George Allen and Unwin,
London, pp 441.
Scheidegger, A.E (1965), “The Algebra of Stream Order Number”, U.S. GeologicalSurvey Professional
Paper, 525B, B1, pp 87-89.
Schumm, S.A (1954), “The relation of Drainage Basin Relief to Sediment Loss”,International
Association of Scientific Hydrology, 36, pp 216-219.
Schumm, S.A (1956), “Evolution of Drainage Systems & Slopes in Badlands at PerthAnboy, New
Jersey”, Bulletin of the Geological Society of America, 67, pp 597-646.
Schumm, S.A (1963), “Sinuosity of Alluvial Rivers on the Great Plains”, Bulletin of the Geological
Society of America, 74, pp 1089-1100.
Shreve, R.L (1966), “Statistical Law of Stream Numbers”, Journal of Geology, 74, pp 17-37.
Singh, P., Gupta, A., and Singh, M., 2014. Hydrological inferences from watershed analysis for water
resource management using remote sensing and GIS techniques. The Egyptian Journal of
Remote Sensing and Space Science, 17(2), 111-121. DOI: 10.1016/j.ejrs.2014.09.003
Smith, G.H (1939), “The Morphometry of Ohio: The Average Slope of the Land (abstract)”, Annals of
the Association of American Geographers, 29, pp 94.
Strahler, A. N., 1957. Quantitative analysis of watershed geomorphology. Transactions, American
Geophysical Union, 38(6), 913-920. DOI: 10.1029/tr038i006p00913

Strahler, A.N (1952), “Hypsometric Analysis of Erosional Topography”, Bulletin of the Geological
Society of America, 63, pp 1117-42.
Strahler, A.N (1956), “Quantitative Slope Analysis”, Bulletin of the GeologicalSociety of America, 67, pp
571-596.
Strahler, A.N (1964), “Quantitative Geomorphology of Drainage Basin and Channel Network”,
Handbook of Applied Hydrology, pp 39-76.
Sujatha, E. R., Selvakumar, R. and Rajasimman, B., 2014. Watershed prioritization of Palar sub-
watershed based on the morphometric and land use analysis. Journal of Mountain Science,
11(4), 906-916. DOI: 10.1007/s11629-012-2628-7
Thornbury, W.D (1954), “Principles of Geomorphology”, John Wiley and Sons, London.
Wentworth, C.K (1930), “A Simplified Method of Determining the Average Slope of Land Surfaces”,
American Journal of Science, 21, pp 184-194.
West, W.D. and Choubey, V.D (1964), "The Geomorphology of the Country around Sagar and Katangi
(M.P.)", Journal of Geological Society of India, 5, pp 41-55.
Wilson, J. S., Chandrasekar, N. and Magesh, N.S., 2012. Morphometric analysis of major sub-
watersheds in Aiyar and Karai Pottanar Basin, central Tamil Nadu, India using remote sensing
and GIS techniques. Bonfring International Journal of Industrial Engineering and Management
Science, 2 (1), 8–15
Woldenberg, N.J (1967), “Geography & Properties of Surface”, Handward Paper in Theoretical
Geography, 1 pp 95-189.
Young, A (1972), "Slope", Oliver & Boyd, Edinburgh, pp 5.
Zwnnitz, E.R (1932) "Drainage Pattern and their Significance", Journal of Geology, XL (6), pp 498-521.

IRJET- Morphometric Analysis of Sina Basin Using GIS and Remote Sensing Techniques

More Related Content

What's hot (18)

Similar to IRJET- Morphometric Analysis of Sina Basin Using GIS and Remote Sensing Techniques (20)

More from IRJET Journal (20)

Recently uploaded (20)

IRJET- Morphometric Analysis of Sina Basin Using GIS and Remote Sensing Techniques