IRJET- Open Channel Flow Characteristics using Gabion Weir

International Research Journal of Engineering and Technology (IRJET) e-ISSN: 2395-0056
Volume: 05 Issue: 12 | Dec 2018 www.irjet.net p-ISSN: 2395-0072
© 2018, IRJET | Impact Factor value: 7.211 | ISO 9001:2008 Certified Journal | Page 928
“OPEN CHANNEL FLOW CHARACTERISTICS USING GABION WEIR”
Pallavi M1, Harshith L2
1Pallavi M Assistant Professor Dept. of Civil Engineering REVA University Karnataka India
2Harshith L Student Dept. of Civil Engineering VVCE Karnataka India
----------------------------------------------------------------------***---------------------------------------------------------------------
Abstract - A solid weir consists of an impermeable body
Constructed of concrete and its primaryfunction isheading up
water and reducing flow velocity. The wire mesh of the
gabion basket serves to restrain any significant movement
and also gabion weirs offer an alternative design that can be
adopted for flash flood mitigation. In this study, a series of
laboratory experiments was performed in order toinvestigate
the open channel flow interaction with gabion and to reduce
the flow velocity. Gabion weir was tested in horizontal
laboratory flume of 4.7-m length, 0.21-m width, and 0.3-m
depth for a wide range of discharge, upstream water depth,
downstream water depth, slope and gabion filling gravel
material size. The experimental results of the gabion weir
were compared with solid weirs having the same dimension
and found that there is a large deviation when the solid weirs
equation is applied to gabion weirs. Discharge over weir was
computed by using multiple regression equations whichwas
developed based on the dimensional analysis theory.
Key Words: Solid Weir, Gabion weir, Discharge co-
efficient, Submerged Flow, Flume
1. INTRODUCTION
A weir is a barrier across the horizontal width of the river
that alters the flow characteristics of the water and usually
results in a change in the vertical height of the river level.
There are many designs of weir but commonly water flows
freely over the top of the weir crest before cascading down
to a lower level. Weirs are commonly used to prevent
flooding, measure discharge and help render rivers
navigable. In some locations the dam and weir are
synonymous, but normally there is a clear distinction made
between the structures. A dam is usually specifically
designed to impound water behind a wall, where as a weiris
designed to alter the river flow characteristics. A common
distinction between dams and weirs is that water flowsover
the top of a weir or underneath it for at least some of its
length. Weirs can vary in size both horizontally and
vertically, with the smallest being only a few inchesinheight
where as the largest may be hundreds of meters long and
many meters tall.
Weirs are overflow structures that stretch across an open
channel of water and are meant to alter the channel’s flow
characteristics making it easier to measure the volumetric
rate of water flow. Weirs act like miniature dams, blocking
the flow of water, and causing it to pool behind them until it
is deep enough to flow over the top of the weir. The height of
the water flowing over the crest of the weir correlates to the
flow rate. Therefore, through equations, graphs and tables
the volumetric flow rate can be determined from measuring
the depth of water flowing over the weir with relativelyhigh
accuracy. In addition to measuring discharge, weirscanhelp
make rivers more navigable and prevent flooding.
1.1 Objective
The main objective of this research work is to study the
behaviour of open channel flow usingstonegabiontoreduce
the flow velocity.
Specific Objective
 To determine the maximum velocity at varying
depths and slopes
 To select the size of stones for Gabion for reduction
in velocity
 To generalize the discharge equation for flow over
gabion using regression analysis
1.2 Literature review
The studies have shown that conventional weir typically
consists of an impermeable body constructed of concrete,
since its primary functions are to heading up water and
efficiently regulate flow. The impermeable body prevents
the longitudinal movement of aquaticlifeandtransportation
of physical and chemical substances in water, eventually
having a negative impact on the water. Hassan I. Mohamed
(2010), carried out the study on Flow over Gabion Weirs.
One of the advantages of gabions as a building material is
that the motion of individual stones comprisingthegabionis
not of much concern. The wire mesh of the gabion basket
serves to restrain any significant movement. In this study, a
series of laboratory experiments was performed in order to
investigate the flow over gabion weirs. For thispurpose,two
different gabion weir models were tested in two horizontal
laboratory flumes of 10m and 17m length, 0.3m width, and
0.3m and 0.5m depth, respectively, for a wide range of
discharge, upstream water depth, downstream waterdepth,
weir height, weir length, and gabion filling gravel material
size.
Vegetation growing in the water along rivers has been the
subject of several studies since it was recognized that it
could have a significant impact on the water flow Hamimed
A et. al., (2013), reviewed on a contribution to the study of
the flow resistance in a flume with artificial emergent
vegetation. The purpose of this paper is to investigate, how
density and placementofemergentvegetationinfluenceflow
resistance, water depth and velocity profile. Experiments
using artificial vegetation selected to simulate emergent

vegetation were carried out in a laboratory flume instead of
natural channel, and Manning’s n is used to denote the
resistance coefficient. The results show large variations in
the Manning resistance coefficient with depth of flow and
vegetative density. Vegetation causes resistance to flow.
Later it was concluded that the measurements showthatthe
water depth-discharge relationship depends stronglyonthe
density of vegetation.
Mahyuddin Ramli et. al., (2013), carried out the study on
the stability of gabion walls for earth retaining structures.
The stability of earth retaining structures in flood prone
areas has become a serious problem in many countries. The
two most basic causes of failure arising from flooding are
scouring and erosion ofthefoundationofthesuperstructure.
According to the US Federal Highway Administration, up to
60% of bridge failures were caused by natural phenomena,
especially from flooding. Gabion walls are also suited to the
following cases; Poor orientationof bridge pierswithrespect
to water flows. Large restrictions in flow imposed by the
bridge superstructure.Fine-grainedmaterials,susceptibleto
move with a small increase in flow velocity. Unpredictable
increases in the water flow. The results indicate that the
hexagonal gabion exhibits better overall structural integrity
than the conventional gabion in terms of deformation
resistance and susceptibility to collapse. The shear behavior
exhibited by each wall illustrates the principal link between
unit configuration and overall stability when cellular units
are built into a continuum.
Experimental study on gabion stepped spillway paper was
presented by M.Shafai-Bajestan et. al., (2009), Rocksinits
natural form is the most abundant and economical material
in hydraulic engineering practice. Rocks have been used in
dam construction, river engineering works,riverintakes etc.
The size of rock in these practices depends on the hydraulic
conditions such on flow velocity, shear stress, hydrostatic
and hydrodynamic pressures. When these conditions are
high, the required size of stone will be large and impractical
Gabions are hexagonal mesh boxes filled with small sizes of
stone. The advantage of gabion is their stability, low cost,
flexibility, porosity. Use of rocks and gabions in hydraulic
works especially in the area of river engineering has been
increased during recent decades. Gabion stepped spillwayis
a type of hydraulic structures which isdesignedforriver bed
protection. Most of the flow kinetic energy is dissipated
when flow cascade from one step to another. The main
objective of this study is to conduct a series of experimental
tests to investigatethe mechanismofscourholedownstream
of stepped spillway. A total of 19 tests were conducted.
To predict the scour dimensions downstream of gabion
stepped spillway, experimental program was conducted.
Three types of spillways with slope of 1V:3.5 H, were tested
under different flow conditions and two bed material sizes.
In this study three types of gabion stepped spillways under
different flow conditions and bed materials were tested.
Based on stability analysis of a particle at the point of
incipient motion, a general formula wasdevelopedtopredict
the scour hole depth. By the help of regression analysis
technique and use of the experimental data, three equations
were developed for predictionofscourdepthatdownstream
of stepped spillways. From these equations, one can predict
the scour depth. It was found that the scour depth
downstream of simple gabion stepped spillway is greater
than the scour depth for pooled stepped spillway. A
procedure for design of gabion stepped spillway is
presented.
2. Materials and Methodology
2.1 Materials
Solid weir and gabion weir (fig 1 and fig 2) are manually
prepared, for measured dimensions and these weirs are
placed at different distances from the inlet of venturiflume
and for different slopes. After conducting the experiments
the velocities and pressures are measured.
Fig -1 Solid weir
Fig -2 Gabion weir
Gabion weir is fabricated using mild steel. Steel rods of
0.01m are used to provide framework to gabion weir. The
clear spacing between the wires of gabions is 0.01m i.e., 1.5-
2 times greater than the size of stones in order to avoid the
stones coming out of gabion weir. Stones are used as filing
material in the Gabion weir. Granite stones that are clean
and durable are collected fromthebanksofBalmuri,Mysore.
Fig 3 shows stone collection at the Balmuri,
Solid weir is fabricated using cement, fine aggregate and
coarse aggregate in the ratio 1:2:4. The dimensions of the
sold weir are kept as same as that of Gabion weir for the
comparison purpose.
Fig- 3 Stones collected from Balmuri, Mysore

2.2 Equipments
 Hydraulic flume
 Abrasion testing machine
 Angularity test apparatus
Hydraulic fumes are engineered structures constructed to
carry water and to measure thedischarge. Hydraulic flumeis
also called as Venturi flume.
The dimension of laboratory hydraulic flume is 4.7m X
0.21m X 0.3m length, breadth and height respectively.
The flume has a provision for the direct measurement of
discharge with the help of venturimeter.
The pressure difference at the inlet and throat region gives
the discharge value.
This discharge valve is taken as actual discharge and the
theoretical discharge value is calculated from weir by
measuring the head over the weir. Fig 4 shows the hydraulic
flume.
Fig- 4 Hydraulic flume
Fig- 5 Los-Angeles abrasion testing machine
Fig- 6 Angularity test apparatus
2.3 Methodology
Experiments are conducted in laboratory using the
instrument called hydraulic flume. This study is deals with
using Gabion weir as a flow reducing structure, which helps
to reduce the velocity by cutting the water depth into
number of layers and also it helps to reduce the turbulence.
2.3.1 Weir Design
Weir dimensions such as length,breadthandheightarefixed
based on maximum water depth in the flume andBernoulli’s
equation.
Height, Width, Length
Weir height is maintained at 0.105m which is well
maintained above the critical depthand belowthe maximum
water level in the flume. The width of the weir should be
equal to the width of the channel. Therefore, the weir
breadth is taken as 0.21m.The length of the weir in the
direction of water flow is taken as 0.10m.
Sieve analysis is carried to separate the different size of
stones. For larger project works, stone size of 100mm-
200mm are used. But for smaller works usually stone size
below 20mm are selected. Hence the stone size selected for
this project work is 16mm and 20mm. Abrasion Test and
Angularity tests on stones are conducted in the laboratory.
2.3.2 Experiment conduction in Hydraulic Flume
 Experiment is carried out in Hydraulic flume of
4.7m X 0.21m X 0.3m, Length (L), width (B) and
height (D) respectively
 Gabion weir is placed at L/4 and L/2 positionsfrom
the inlet of the flume
 Upstream water depth and downstream water
depth is measured using hook gauge at 00, 1.50 and
30 slopes
 Experimental procedure is repeated for solid weir
also and the corresponding upstream and
downstream water depths are measure
 The pressure difference between the inlet and
throat region of venturi meter is noted down to
determine the actual discharge
 Dimensional analysis and regression analysis is
carried out to develop new discharge equation for
the gabion weir
 The discharge equation obtained from the multi-
regression analysis is used to calculate theoretical
discharge over the gabion weir
 Co-efficient of discharge is then calculatedbytaking
ratio of actual discharge by theoretical discharge
 Chezy equation is used to determine the velocity
over the weir i.e., Vth= Cd
 The velocity of solid weir and gabion weir is
compared and the reduction in velocity is noted
down

3. RESULT AND DISCUSSION
Experiments are conducted in hydraulic flume at different
slopes and different depth with solid weir and gabion weir.
The discharge value of solid weir and gabion weir are
tabulated and test on stone is performed in the laboratory.
The experimental discharge value for different stone sized
gabion weir and solid weir are calculated using venture
meter. The following table-1 shows the venturi meter
readings.
Table-1: Venturi meter readings
Sl
no Particulars Readings
1 Inlet diameter of venturimeter d1 0.09 m
2 Throat diameter of venturimeter d2 0.035 m
3 Area at inlet region a1 0.0064 m2
4 Area at throat region a2 0.0010 m2
For solid weir and gabion weir of 16mm stone size and
20mm stone size, fixed slopes and distances of weir position
from the inlet of venturi flume are shown in table-2. Based
on this table (slopes and distances) the readingsaretakenin
the instrument venturi flume
The measured pressure, discharge values for one fixed
distance and slope, of solid weir shown in table-3. The
measured pressure and discharge values for one fixed
distance and slope, of Gabion weir of 16mm stone size and
20mm stone size shown in table-4 and table-5. And for
Different distances (L/4 distance from the inlet) and varying
slopes for solid weir and gabion weir are placed shown in fig
7 and fig 8
Table-2: Type of weir, slope and distance from inlet
Table -3: Discharge value at 1 in 0.33 gradient and L/2
position for solid weir
position for gabion weir of 16mm stone size
Sl
no
Venturi Flume reading for gabion weir of 16mm stone
size
P1(kg/cm2) P2(kg/cm2)
H =(P1-P2)
m Q (m3/s)
1 0 0 0 0
2 0 0 0 0
3 0.05 -0.05 1 0.00387
4 0.05 -0.05 1 0.00387
5 0.05 -0.05 1 0.00387
6 0.05 -0.05 1 0.00387
7 0.1 -0.05 1.5 0.00474
8 0.1 -0.05 1.5 0.00474
9 0.1 -0.05 1.5 0.00474
10 0.1 -0.1 2 0.00548
11 0.1 -0.1 2 0.00548
position for gabion weir of 20mm stone size
Sl
no
Venturi Flume reading for gabion weir of 20mm stone
size
P1(kg/cm2) P2(kg/cm2) H =(P1-P2) m Q (m3/s)
1 0 0 0 0.000000
2 0 0 0 0.000000
3 0 0 0 0.000000
4 0.05 -0.05 1 0.003878
5 0.1 -0.05 1.5 0.004750
6 0.1 -0.1 2 0.005484
7 0.1 -0.1 2 0.005484
8 0.15 -0.2 3.5 0.007255
9 0.15 -0.2 3.5 0.007255
10 0.15 -0.2 3.5 0.007255
11 0.15 -0.2 3.5 0.007255
Type of Weir Slope in
gradient
Distance ofweir
position from
inlet of venturi
flume
1 Solid weir
2 Gabion weir
(16mm stone size)
3 Gabion weir
(20mm stone size)
0
0
1 in 0.33
1 in 0.33
1 in 0.66
1 in 0.66
L/2 Position
L/4 Position
L/2 Position
L/4 Position
L/2 Position
L/4 Position
Slno Venturi Flume reading for solid weir
P1(kg/cm2) P2(kg/cm2) H =(P1-P2)m
Q
(m3/s)
1 0 0.1 -1 0.00387
2 0 0.1 -1 0.00387
3 0.05 0.05 0 0
4 0.1 0 1 0.00387
5 0.15 -0.05 2 0.00548
6 0.15 -0.05 2 0.00548
7 0.15 -0.05 2 0.00548
8 0.15 -0.1 2.5 0.00613
9 0.15 -0.1 2.5 0.00613
10 0.15 -0.1 2.5 0.00613
11 0.15 -0.1 2.5 0.00613

Fig -7: Gabion weir placed at L/4 distance from inlet
Fig -8: solid weir placed at L/4 distance from inlet
4. CONCLUSIONS
In this study, a series of laboratory experiments were
conducted to investigate the flow through and over gabion
weir. According to the results of the laboratoryexperiments,
the following conclusions are drawn
1. The nature of flow over the gabion weir is different than
that of the solid weir. As it is dividing into two parts one
is above the weir and to other flowing through the weir
2. For the same discharge, the head over the gabion weir is
less than that over the solid weir and the head decreases
by increasing gabion material particle size
3. Multiple regression analysis equations based on the
dimensional analysis concept were developed for
computing the discharge over the gabion weir atfreeand
submerged flow conditions
4. Gabion weir is more effective at slope than solid weir as
the velocity of flowing water reduces as it pass through
the weir
REFERENCES
[1] Ansar M and Gonzalez-Castro J. A. (2003). “Submerged
weir flow at prototype gated spillways”. World Water
Congress, ASCE, Vol.12, pp.321-321
[2] Gogus, M. Defne, and ozkandemir V. (2006) “Broad-
crested weirs with rectangular compound cross
sections”. Journal of Irrigation engineering. Drainage,
Vol.132(3), pp.272–280
[3] Hager, W. H., and Schwalt, M. 1994. “Broad-crested
weir”. Journal of Irrigation Drainage. Vol 120(1), pp.13–
26
[4] Kells J. A. (1993) “Spatially varied flow over rock-fill
embankments”. Journal of Civil Engineering, Vol-20,
pp.820–827
[5] Leu J. M., Chan H. C., and Chu M. S. (2008). “Comparison
of turbulent flow over solid and porous structures
mounted on the bottom of a rectangular channel”. Flow
Measuring Instrument, Vol.(19), pp.1–7
[6] Kells J. A. (2004) “Reply on discussion of spatiallyvaried
flow over rockfill embankments”. Journal of Civil
Engineerinng, Vol.21, pp.163–166.
[7] Li, B., and Garga, V. K. (2008). “Theoretical solution for
seepage flow in overtopped rockfill”. Journal of
Hydraulic Engineering., Vol.12 (2), pp.213–217
[8] Michioku, K., Maeno, S., Furusawa, T., and Haneda, M.
(2005). “Discharge through a permeable rubble mound
weir”. Journal of Hydraulic Engineering, Vol.131 (1),
pp.1–10
[9] Michioku, K., Takehara, K., and Etoh, T. (2007), “An
experimental study on flow field in and around rubble
mound river structures” Journal of Hydro science Eng.,
Vol.25(2), pp.37–45
[10] Mohamed H. I. (2005). “Discharge measurement in
trapezoidal lined canals utilizing horizontal andvertical
transitions”. 9th International Water Technology
Conference, Vol.55, pp.12-17
[11] Reston and Va. Chanson, H (2006) “Discussion of
discharge through a permeable rubble mound
weir”.Journal of Hydraulic Engineering. Vol 13(4),
pp.432–434
[12] Sargison, J. E., and Percy, A. (2009). “Hydraulics of
broad-crested weirs with varying sideslopes”.Journal of
Irrigation Drainage., Vol.135(1), pp.115–118
[13] Bligh WG. “Dams barrages and weirs on porous
foundations”, Engineering News, 1910, Vol. 64, 708
[14] Lane EW. “Security from under seepage: Masonry Dams
on Earth Foundations”, Trans, ASCE, 1935, pp. 1235-
1272
[15] Khosla AN, Bose NK, McKenzie ET. “Design of weirs on
pervious foundations”, Publication number 12 of the
Central Board of Irrigation, Simla, India, 1936
[16] Harr ME. “Groundwater and Seepage”, McGraw-Hill,
NewYork, 1962

[17] Pavlovsky NN. “The theory of ground water flow
beneath hydrotechnical structures”, Research
Melioration Institute
[18] Leliavsky S. “Irrigation and hydraulic design”, Chapman
and Hall, London, 1955.
[19] Polubarinova-Kochina PY. “Theory of groundwater
movement”, Trans. JM. Roger de Wiest, Princeton
University, Princeton, NJ, 1962
[20] Fil’chakov PF. “The theory of filtration beneath
hydrotechnical structures”, Vol.1,Izd-voAkademiinauk
Ukrainskoi SSR, Kiev, 1959
[21] Abedi Koupaei J. “Investigation of effective elements on
uplift pressure upon diversion dams by using finite
difference”, thesis for MSC (in Persian), University of
Tarbiat Modarres, Tehran, Iran, 1991
[22] Griffiths DV, Fenton GA. “Three-dimensional seepage
through spatially random soil”, Journal of Geotechnical
and Geoenviromental Engineering, 1997, Vol. 123, pp.
153-160

IRJET- Open Channel Flow Characteristics using Gabion Weir

More Related Content

What's hot (20)

Similar to IRJET- Open Channel Flow Characteristics using Gabion Weir (20)

More from IRJET Journal (20)

Recently uploaded (20)

IRJET- Open Channel Flow Characteristics using Gabion Weir