J overvoltage-protection-2
2 likes1,016 views
1) The document discusses the design of electrical installation protection systems. It outlines rules for selecting surge protective devices (SPDs) based on factors like the quantity of SPDs needed, their type, and the level of exposure. 2) The key characteristics used to define the lightning protection system and select an SPD include the SPD's maximum discharge current, the short-circuit current at the installation point, and whether a lightning rod is present within 50 meters of the building. 3) Multiple levels of SPD protection can be installed, with a Type 1 SPD at the incoming end to absorb a large quantity of energy, Type 2 SPDs to absorb residuals, and optional Type 3 SPDs near sensitive equipment
J overvoltage-protection-2
- 1. J - Protection against voltage surges in LV 3 Design of the electrical installation protection system 3.1 Design rules To protect an electrical installation in a building, simple rules apply for the choice of b SPD(s); b its protection system. For a power distribution system, the main characteristics used to define the lightning protection system and select a SPD to protect an electrical installation in a building are: b SPD v quantity of SPD; v type; v level of exposure to define the SPD's maximum discharge current Imax. b Short circuit protection device v maximum discharge current Imax; v short-circuit current Isc at the point of installation. The logic diagram in the Figure J20 below illustrates this design rule. Surge Protective Device (SPD) No Is there a lightning rod on the building or within 50 metres of the building ? Yes Type2 SPD Risks level ? Low 20 kA Type 1 + Type2 or Type 1+2 SPD Risks level ? Medium 40 kA High 65 kA 12,5 kA mini. Imax J13 25 kA Iimp Isc at the installation point ? Short Circuit Protection Device (SCPD) Fig. J20 : Logic diagram for selection of a protection system This sub-section J3 describes in greater detail the criteria for selection of the protection system according to the characteristics of the installation, the equipment to be protected and the environment. © Schneider Electric - all rights reserved The other characteristics for selection of a SPD are predefined for an electrical installation. b number of poles in SPD; b voltage protection level Up; b operating voltage Uc. Schneider Electric - Electrical installation guide 2010 EIG_Chapter_J.indb 13 11/03/2010 09:46:01
- 2. J - Overvoltage protection A SPD must always be installed at the origin of the electrical installation. 3.2 Elements of the protection system 3.2.1 Location and type of SPD The type of SPD to be installed at the origin of the installation depends on whether or not a lightning protection system is present. If the building is fitted with a lightning protection system (as per IEC 62305), a Type 1 SPD should be installed. For SPD installed at the incoming end of the installation, the IEC 60364 installation standards lay down minimum values for the following 2 characteristics: b Nominal discharge current In = 5 kA (8/20) µs; b Voltage protection level Up (at In) < 2.5 kV. The number of additional SPDs to be installed is determined by: b the size of the site and the difficulty of installing bonding conductors. On large sites, it is essential to install a SPD at the incoming end of each subdistribution enclosure. b the distance separating sensitive loads to be protected from the incoming-end protection device. When the loads are located more than 30 m away from the incoming-end protection device, it is necessary to provide for special fine protection as close as possible to sensitive loads. b the risk of exposure. In the case of a very exposed site, the incoming-end SPD cannot ensure both a high flow of lightning current and a sufficiently low voltage protection level. In particular, a Type 1 SPD is generally accompanied by a Type 2 SPD. The table in Figure J21 below shows the quantity and type of SPD to be set up on the basis of the two factors defined above. J14 No Yes Is there a lightning rod on the building or within 50 metres of the building ? one Type 1 and one Type 2 SPD (or one Type 1+2 SPD) in the main switchboard one Type 2 SPD in the main switchboard D < 30 m Incoming circuit breaker Distance (D) separating sensitive equipment from lightning protection system installed in main switchboard © Schneider Electric - all rights reserved Incoming circuit breaker Type 1 + Type 2 SPD Type 2 SPD D D one Type 2 SPD in main switchboard one Type 2/Type 3 SPD in the enclosure close to sensitive equipment one Type 1 and one Type 2 SPD (or one Type 1+2 SPD) in the main switchboard one Type 2/Type 3 SPD in the enclosure close to sensitive equipment Incoming circuit breaker Type 2 SPD Incoming circuit breaker Type 1 + Type 2 SPD Type 3 SPD D > 30 m Type 3 SPD D D Fig. J21 : The 4 cases of SPD implementation Note : The Type 1 SPD is installed in the electrical switchboard connected to the earth lead of the lightning protection system. Schneider Electric - Electrical installation guide 2010 EIG_Chapter_J.indb 14 11/03/2010 09:46:02
- 3. 3 Design of the electrical installation protection system 3.2.2 Protection distributed levels Several protection levels of SPD allows the energy to be distributed among several SPDs, as shown in Figure J22 in which the three types of SPD are provided for: b Type 1: when the building is fitted with a lightning protection system and located at the incoming end of the installation, it absorbs a very large quantity of energy; b Type 2: absorbs residual overvoltages; b Type 3: provides "fine" protection if necessary for the most sensitive equipment located very close to the loads. Main LV Switchboard Subdistribution Board Fine Protection Enclosure (incoming protection) 90 % 9% 1% Sensitive Equipment Type 1 SPD Type 2 SPD Type 3 SPD J15 Discharge Capacity (%) Fig. J22 : Fine protection architecture Note: The Type 1 and 2 SPD can be combined in a single SPD N PRD1 25 r L1 L2 L3 PRD1 25 r © Schneider Electric - all rights reserved Fig. J23 : The PRD1 25r SPD fulfils the two functions of Type 1 and Type 2 (Type 1+2) in the same product Schneider Electric - Electrical installation guide 2010 EIG_Chapter_J.indb 15 11/03/2010 09:46:02
- 4. J - Overvoltage protection 3.3 Common characteristics of SPDs according to the installation characteristics 3.3.1 Operating voltage Uc Depending on the system earthing arrangement, the maximum continuous operating voltage Uc of SPD must be equal to or greater than the values shown in the table in Figure J24. SPDs connected between System configuration of distribution network IT without IT with distributed distributed neutral neutral TN-C TN-S Line conductor and neutral conductor 1.1 Uo NA 1.1 Uo 1.1 Uo NA Each line conductor and PE conductor 1.1 Uo NA 1.1 Uo 3Uo Vo Neutral conductor and PE conductor Uo NA Uo Uo NA Each line conductor and PEN conductor J16 TT NA 1.1 Uo NA NA NA NA: not applicable NOTE 1: Uo is the line-to-neutral voltage, Vo is the line-to-line voltage of the low voltage system. NOTE 2: This table is based on IEC 61643-1 amendment 1. Fig. J24 : Stipulated minimum value of Uc for SPDs depending on the system earthing arrangement (based on Table 53C of the IEC 60364-5-53 standard) The most common values of Uc chosen according to the system earthing arrangement. TT, TN: 260, 320, 340, 350 V IT: 440, 460 V 3.3.2 Voltage protection level Up (at In) The 443-4 section of IEC 60364 standard, “Selection of equipment in the installation”, helps with the choice of the protection level Up for the SPD in function of the loads to be protected. The table of Figure J25 indicates the impulse withstand capability of each kind of equipment. © Schneider Electric - all rights reserved Nominal voltage of the installation(1) V Three-phase Single-phase systems(2) systems with middle point 230/400(2) 277/480(2) 400/690 1,000 120-240 - Required impulse withstand voltage for kV Equipment at Equipment of Appliances the origin of distribution and the installation final circuits (impulse (impulse (impulse withstand withstand withstand category IV) category III) category II) 4 2.5 1.5 6 4 2.5 - 8 6 4 Values subject to system engineers Specially protected equipment (impulse withstand category I) 0.8 1.5 2.5 (1) As per IEC 60038. (2) In Canada and the United States, for voltages exceeding 300 V relative to earth, the impulse withstand voltage corresponding to the immediately higher voltage in the column is applicable. (3) This impulse withstand voltage is applicable between live conductors and the PE conductor Fig. J25 : Equipment impulse withstand category for an installation in conformity with IEC 60364 (Table 44B). Schneider Electric - Electrical installation guide 2010 EIG_Chapter_J.indb 16 11/03/2010 09:46:02
- 5. 3 Design of the electrical installation protection system b Equipment of overvoltage category I is only suitable for use in the fixed installation of buildings where protective means are applied outside the equipment – to limit transient overvoltages to the specified level. Examples of such equipment are those containing electronic circuits like computers, appliances with electronic programmes, etc. b Equipment of overvoltage category II is suitable for connection to the fixed electrical installation, providing a normal degree of availability normally required for current-using equipment. Examples of such equipment are household appliances and similar loads. b Equipment of overvoltage category III is for use in the fixed installation downstream of, and including the main distribution board, providing a high degree of availability. Examples of such equipment are distribution boards, circuit-breakers, wiring systems including cables, bus-bars, junction boxes, switches, socket-outlets) in the fixed installation, and equipment for industrial use and some other equipment, e.g. stationary motors with permanent connection to the fixed installation. b Equipment of overvoltage category IV is suitable for use at, or in the proximity of, the origin of the installation, for example upstream of the main distribution board. Examples of such equipment are electricity meters, primary overcurrent protection devices and ripple control units. J17 Fig. J26 : Overvoltage category of equipment The "installed" Up performance should be compared with the impulse withstand capability of the loads. SPD has a voltage protection level Up that is intrinsic, i.e. defined and tested independently of its installation. In practice, for the choice of Up performance of a SPD, a safety margin must be taken to allow for the overvoltages inherent in the installation of the SPD (see Fig. J27). U1 Up Loads to be protected Installed = Up + U1 + U2 Up Fig. J27 : "Installed" Up The "installed" voltage protection level Up generally adopted to protect sensitive equipment in 230/400 V electrical installations is 2.5 kV (overvoltage category II, Note: If the stipulated voltage protection level cannot be achieved by the incoming-end SPD or if sensitive equipment items are remote (see section 3.2.1), additional coordinated SPD must be installed to achieve the required protection level. see Fig. J28). © Schneider Electric - all rights reserved U2 Schneider Electric - Electrical installation guide 2010 EIG_Chapter_J.indb 17 11/03/2010 09:46:03
- 6. J - Overvoltage protection 3.3.3 Number of poles b Depending on the system earthing arrangement, it is necessary to provide for a SPD architecture ensuring protection in common mode (CM) and differential mode (DM). TT TN-C TN-S IT Phase-to-neutral (DM) Recommended1 - Recommended Not useful Phase-to-earth (PE or PEN) (CM) Yes Yes Yes Yes Neutral-to-earth (PE) (CM) Yes - Yes Yes2 1 The protection between phase and neutral can either be incorporated in the SPD placed at the origin of the installation, or be remoted close to the equipment to be protected 2 If neutal distributed Fig. J28 : Protection need according to the system earthing arrangement Note: b Common-mode overvoltage A basic form of protection is to install a SPD in common mode between phases and the PE (or PEN) conductor, whatever the type of system earthing arrangement used. b Differential-mode overvoltage In the TT and TN-S systems, earthing of the neutral results in an asymmetry due to earth impedances which leads to the appearance of differential-mode voltages, even though the overvoltage induced by a lightning stroke is common-mode. 2P, 3P and 4P SPDs (see Fig. J29) J18 b These are adapted to the TT and TN-S systems. b They provide protection merely against common-mode overvoltages. Fig. J29 : 2P, 3P, 4P SPDs 1P + N, 3P + N SPDs (see Fig. J30) © Schneider Electric - all rights reserved b These are adapted to the TT and TN-S systems. b They provide protection against common-mode and differential-mode overvoltages. Fig. J30 : 1P + N, 3P + N SPDs Schneider Electric - Electrical installation guide 2010 EIG_Chapter_J.indb 18 11/03/2010 09:46:03
- 7. 3 Design of the electrical installation protection system 3.4 Selection of a Type 1 SPD 3.4.1 Impulse current Iimp b Where there are no national regulations or specific regulations for the type of building to be protected: the impulse current Iimp shall be at least 12.5 kA (10/350 µs wave) per branch in accordance with IEC 60364-5-534. b Where regulations exist: standard 62305-2 defines 4 levels: I, II, III and IV The table in Figure J31 shows the different levels of Iimp in the regulatory case. Protection level as per EN 62305-2 External lightning protection system designed to handle direct flash of: Minimum required Iimp for Type 1 SPD for line-neutral network I 200 kA 25 kA/pole II 150 kA 18.75 kA/pole III / IV 100 kA 12.5 kA/pole Fig. J31 : Table of Iimp values according to the building's voltage protection level (based on IEC/EN 62305-2) 3.4.2 Autoextinguish follow current Ifi J19 This characteristic is applicable only for SPDs with spark gap technology. The autoextinguish follow current Ifi must always be greater than the prospective shortcircuit current Isc at the point of installation. 3.5 Selection of a Type 2 SPD 3.5.1 Maximum discharge current Imax The maximum discharge current Imax is defined according to the estimated exposure level relative to the building's location. The value of the maximum discharge current (Imax) is determined by a risk analysis (see table in Figure J32). Exposure level Low Medium High Building environment Building located in an urban or suburban area of grouped housing Building located in a plain Building where there is a specific risk: pylon, tree, mountainous region, wet area or pond, etc. Recommended Imax value (kÂ) 20 40 65 © Schneider Electric - all rights reserved Fig. J32 : Recommended maximum discharge current Imax according to the exposure level Schneider Electric - Electrical installation guide 2010 EIG_Chapter_J.indb 19 11/03/2010 09:46:03
- 8. J - Overvoltage protection The protection devices (thermal and short circuit) must be coordinated with the SPD to ensure reliable operation, i.e. b ensure continuity of service: v withstand lightning current waves; v not generate excessive residual voltage. b ensure effective protection against all types of overcurrent: v overload following thermal runaway of the varistor; v short circuit of low intensity (impedant); v short circuit of high intensity. 3.6 Selection of external Short Circuit Protection Device (SCPD) 3.6.1 Risks to be avoided at end of life of the SPDs b Due to ageing In the case of natural end of life due to ageing, protection is of the thermal type. SPD with varistors must have an internal disconnector which disables the SPD. Note: End of life through thermal runaway does not concern SPD with gas discharge tube or encapsulated spark gap. b Due to a fault The causes of end of life due to a short-circuit fault are: v Maximum discharge capacity exceeded. This fault results in a strong short circuit. v A fault due to the distribution system (neutral/phase switchover, neutral disconnection). v Gradual deterioration of the varistor. The latter two faults result in an impedant short circuit. The installation must be protected from damage resulting from these types of fault: the internal (thermal) disconnector defined above does not have time to warm up, hence to operate. A special device called "external Short Circuit Protection Device (external SCPD) ", capable of eliminating the short circuit, should be installed. It can be implemented by a circuit breaker or fuse device. J20 3.6.2 Characteristics of the external SCPD The external SCPD should be coordinated with the SPD. It is designed to meet the following two constraints: Lightning current withstand The lightning current withstand is an essential characteristic of the SPD's external Short Circuit Protection Device. The external SCPD must not trip upon 15 successive impulse currents at In. Short-circuit current withstand b The breaking capacity is determined by the installation rules (IEC 60364 standard): The external SCPD should have a breaking capacity equal to or greater than the prospective short-circuit current Isc at the installation point (in accordance with the IEC 60364 standard). b Protection of the installation against short circuits In particular, the impedant short circuit dissipates a lot of energy and should be eliminated very quickly to prevent damage to the installation and to the SPD. © Schneider Electric - all rights reserved The right association between a SPD and its external SCPD must be given by the manufacturer. Schneider Electric - Electrical installation guide 2010 EIG_Chapter_J.indb 20 11/03/2010 09:46:03
- 9. 3 Design of the electrical installation protection system 3.6.3 Installation mode for the external SCPD b Device "in series" The SCPD is described as "in series" (see Fig. J33) when the protection is performed by the general protection device of the network to be protected (for example, connection circuit breaker upstream of an installation). Fig. J33 : SCPD "in series" b Device "in parallel" The SCPD is described as "in parallel" (see Fig. J34) when the protection is performed specifically by a protection device associated with the SPD. b The external SCPD is called a "disconnecting circuit breaker" if the function is performed by a circuit breaker. b The disconnecting circuit breaker may or may not be integrated into the SPD. J21 Fig. J34 : SCPD "in parallel" © Schneider Electric - all rights reserved Note: In the case of a SPD with gas discharge tube or encapsulated spark gap, the SCPD allows the current to be cut immediately after use. Schneider Electric - Electrical installation guide 2010 EIG_Chapter_J.indb 21 11/03/2010 09:46:04
- 10. J - Overvoltage protection 3.6.4 Guarantee of protection The external SCPD should be coordinated with the SPD, and tested and guaranteed by the SPD manufacturer in accordance with the recommendations of the IEC 61643-11 standard (NF EN 61643-1) Chap. 7.7.3. It should also be installed in accordance with the manufacturer's recommendations. When this device is integrated, conformity with product standard IEC 61643-11 naturally ensures protection. + Fig. J35 : SPDs with external SCPD, non-integrated (C60N + PRD 40r) and integrated (Quick PRD 40r) 3.6.5 Summary of external SCPDs characteristics A detailed analysis of the characteristics is given in section 6.4. The table in Figure J36 shows, on an example, a summary of the characteristics according to the various types of external SCPD. J22 Installation mode for the external SCPD Surge protection of equipment Protection of installation at end of life Continuity of service at end of life © Schneider Electric - all rights reserved Maintenance at end of life In series In parallel Fuse protection associated = Circuit breaker protection associated = Circuit breaker protection integrated = = SPDs protect the equipment satisfactorily whatever the kind of associated external SCPD No guarantee of protection possible -The complete installation is shut down -Shutdown of the installation required = + Manufacturer's guarantee Protection from impedant short circuits not well ensured ++ Full guarantee Protection from short circuits perfectly ensured + + + + + Only the SPD circuit is shut down = Change of fuses Immediate resetting Fig. J36 : Characteristics of end-of-life protection of a Type 2 SPD according to the external SCPDs 3.7 SPD and protection device coordination table The table in Figure J37 below shows the coordination of disconnecting circuit breakers (external SCPD) for Type 1 and 2 SPDs of the Schneider Electric brand for all levels of short-circuit currents. Coordination between SPD and its disconnecting circuit breakers, indicated and guaranteed by Schneider Electric, ensures reliable protection (lightning wave withstand, reinforced protection of impedant short-circuit currents, etc.) Schneider Electric - Electrical installation guide 2010 EIG_Chapter_J.indb 22 11/03/2010 09:46:04
- 11. 3 Design of the electrical installation protection system Isc (kA) Type 2 - class II Type 1 - class I SCPD not integrated SCPD integrated 70 Need a more specific study 50 NG125L 80A(1) NG125L 80A(1) PRF1(3) 12.5r PRD1(3) Master NG125H 80A(1) NG125H 80A(1) PRF1(3) 12.5r PRD1 Master 36 25 NG125N(2) 40A(2) NG125N(2) 50A(2) NG125N 80A(1) PF 20/ PRD 20r PF 40/ PRD 40r PF 65/ PRD 65r PRF1(3) 12.5r C60H 25A(1) C60H 40A(1) C60H 50A(1) PF 40/ PRD 40r PF 65/ PRD 65r C60L 20A(1) C60L 25A(1) PF 8/ PRD 8r C60H 20A(1) 15 Quick PRD 8r PF 8/ PRD 8r Quick PRD 20r PF 20/ PRD 20r Quick PRD 40r C120H or NG125N 80A(1) J23 NG125N 80A(1) PRF1(3) 12.5r 10 C60N 20A(1) C60N 25A(1) C60N 40A(1) C60N 50A(1) C120N 80A(1) PRD1 25r 6 PF 8/ PRD 8r PF 20/ PRD 20r PF 40/ PRD 40r PF 65/ PRD 65r PRF1 12.5r(3) Imax 8 kA 20 kA 40 kA 65 kA Low risk Medium risk High risk No lightning rod Fig. J22 : Coordination table between SPDs and their disconnecting circuit breakers of the Schneider Electric brand (1): All circuit breakers are C curve - (2): NG 125 L for 1P & 2P - (3): Also Type 2 (class II) tested 12.5 kA 25 kA Maximum risk Lightning rod on the building or within 50 m of the building 3.7.1 Coordination with upstream protection devices Note: S type residual current devices in conformity with the IEC 61008 or IEC 61009-1 standards comply with this requirement. Coordination with overcurrent protection devices In an electrical installation, the external SCPD is an apparatus identical to the protection apparatus: this makes it possible to apply discrimination and cascading techniques for technical and economic optimization of the protection plan. Coordination with residual current devices If the SPD is installed downstream of an earth leakage protection device, the latter should be of the "si" or selective type with an immunity to pulse currents of at least 3 kA (8/20 µs current wave). © Schneider Electric - all rights reserved Dedicated protection to be added when equipment is more than 30m from switchboard. Schneider Electric - Electrical installation guide 2010 EIG_Chapter_J.indb 23 11/03/2010 09:46:05