Lte 3 gpp

ETSI TS 136 214 V11.0.0 (2012-10)
LTE;
Evolved Universal Terrestrial Radio Access (E-UTRA);
Physical layer;
Measurements
(3GPP TS 36.214 version 11.0.0 Release 11)
Technical Specification

ETSI
ETSI TS 136 214 V11.0.0 (2012-10)13GPP TS 36.214 version 11.0.0 Release 11
Reference
RTS/TSGR-0136214vb00
Keywords
LTE
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88
Important notice
Individual copies of the present document can be downloaded from:
http://www.etsi.org
The present document may be made available in more than one electronic version or in print. In any case of existing or
perceived difference in contents between such versions, the reference version is the Portable Document Format (PDF).
In case of dispute, the reference shall be the printing on ETSI printers of the PDF version kept on a specific network drive
within ETSI Secretariat.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
http://portal.etsi.org/tb/status/status.asp
If you find errors in the present document, please send your comment to one of the following services:
http://portal.etsi.org/chaircor/ETSI_support.asp
Copyright Notification
No part may be reproduced except as authorized by written permission.
The copyright and the foregoing restriction extend to reproduction in all media.
© European Telecommunications Standards Institute 2012.
All rights reserved.
DECT
TM
, PLUGTESTS
TM
, UMTS
TM
and the ETSI logo are Trade Marks of ETSI registered for the benefit of its Members.
3GPP
TM
and LTE™ are Trade Marks of ETSI registered for the benefit of its Members and
of the 3GPP Organizational Partners.
GSM® and the GSM logo are Trade Marks registered and owned by the GSM Association.

ETSI
Intellectual Property Rights
IPRs essential or potentially essential to the present document may have been declared to ETSI. The information
pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found
in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in
respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web
server (http://ipr.etsi.org).
Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee
can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web
server) which are, or may be, or may become, essential to the present document.
Foreword
This Technical Specification (TS) has been produced by ETSI 3rd Generation Partnership Project (3GPP).
The present document may refer to technical specifications or reports using their 3GPP identities, UMTS identities or
GSM identities. These should be interpreted as being references to the corresponding ETSI deliverables.
The cross reference between GSM, UMTS, 3GPP and ETSI identities can be found under
http://webapp.etsi.org/key/queryform.asp.

ETSI
Contents
Intellectual Property Rights................................................................................................................................2
Foreword.............................................................................................................................................................2
Foreword.............................................................................................................................................................4
1 Scope........................................................................................................................................................5
2 References................................................................................................................................................5
3 Definitions, symbols and abbreviations ...................................................................................................6
3.1 Definitions..........................................................................................................................................................6
3.2 Symbols..............................................................................................................................................................6
3.3 Abbreviations .....................................................................................................................................................6
4 Control of UE/E-UTRAN measurements.................................................................................................6
5 Measurement capabilities for E-UTRA....................................................................................................7
5.1 UE measurement capabilities .............................................................................................................................7
5.1.1 Reference Signal Received Power (RSRP)...................................................................................................7
5.1.2 Void ..............................................................................................................................................................8
5.1.3 Reference Signal Received Quality (RSRQ) ................................................................................................8
5.1.4 UTRA FDD CPICH RSCP...........................................................................................................................8
5.1.5 UTRA FDD carrier RSSI..............................................................................................................................8
5.1.6 UTRA FDD CPICH Ec/No...........................................................................................................................9
5.1.7 GSM carrier RSSI.........................................................................................................................................9
5.1.8 UTRA TDD carrier RSSI .............................................................................................................................9
5.1.9 UTRA TDD P-CCPCH RSCP......................................................................................................................9
5.1.10 CDMA2000 1x RTT Pilot Strength..............................................................................................................9
5.1.11 CDMA2000 HRPD Pilot Strength..............................................................................................................10
5.1.12 Reference signal time difference (RSTD)...................................................................................................10
5.1.13 UE GNSS Timing of Cell Frames for UE positioning................................................................................10
5.1.14 UE GNSS code measurements....................................................................................................................10
5.1.15 UE Rx – Tx time difference........................................................................................................................10
5.2 E-UTRAN measurement abilities.....................................................................................................................11
5.2.1 DL RS TX power........................................................................................................................................11
5.2.2 Received Interference Power ......................................................................................................................11
5.2.3 Thermal noise power ..................................................................................................................................11
5.2.4 Timing advance (TADV)...............................................................................................................................12
5.2.5 eNB Rx – Tx time difference......................................................................................................................12
5.2.6 E-UTRAN GNSS Timing of Cell Frames for UE positioning....................................................................12
5.2.7 Angle of Arrival (AoA) ..............................................................................................................................12
5.2.8 UL Relative Time of Arrival (TUL-RTOA) .....................................................................................................13
Annex A (informative): Change history ...............................................................................................14
History..............................................................................................................................................................15

ETSI
Foreword
This Technical Specification has been produced by the 3rd
Generation Partnership Project (3GPP).
The contents of the present document are subject to continuing work within the TSG and may change following formal
TSG approval. Should the TSG modify the contents of the present document, it will be re-released by the TSG with an
identifying change of release date and an increase in version number as follows:
Version x.y.z
where:
x the first digit:
1 presented to TSG for information;
2 presented to TSG for approval;
3 or greater indicates TSG approved document under change control.
Y the second digit is incremented for all changes of substance, i.e. technical enhancements, corrections,
updates, etc.
z the third digit is incremented when editorial only changes have been incorporated in the document.

ETSI
1 Scope
The present document contains the description and definition of the measurements done at the UE and network in order
to support operation in idle mode and connected mode.
2 References
The following documents contain provisions which, through reference in this text, constitute provisions of the present
document.
• References are either specific (identified by date of publication, edition number, version number, etc.) or
non-specific.
• For a specific reference, subsequent revisions do not apply.
• For a non-specific reference, the latest version applies. In the case of a reference to a 3GPP document (including
a GSM document), a non-specific reference implicitly refers to the latest version of that document in the same
Release as the present document.
[1] 3GPP TR 21.905: 'Vocabulary for 3GPP Specifications'.
[2] 3GPP TS 36.201: 'Evolved Universal Terrestrial Radio Access (E-UTRA); Physical Layer –
General Description '.
[3] 3GPP TS 36.211: 'Evolved Universal Terrestrial Radio Access (E-UTRA); Physical channels and
modulation'.
[4] 3GPP TS 36.212: 'Evolved Universal Terrestrial Radio Access (E-UTRA); Multiplexing and
channel coding '.
[5] 3GPP TS 36.213: 'Evolved Universal Terrestrial Radio Access (E-UTRA); Physical layer
procedures '.
[6] 3GPP TS 36.321: 'Evolved Universal Terrestrial Radio Access (E-UTRA); Medium Access
Control (MAC) protocol specification'.
[7] 3GPP TS 36.331: 'Evolved Universal Terrestrial Radio Access (E-UTRA); Radio Resource
Control (RRC); Protocol specification '.
[8] 3GPP2 CS.0005-D v1.0 'Upper Layer (Layer 3) Signaling Standard for CDMA2000 Spread
Spectrum Systems Release D'.
[9] 3GPP2 CS.0024-A v3.0 'cdma2000 High Rate Packet Data Air Interface Specification'
[10] 3GPP TS 36.104: 'Evolved Universal Terrestrial Radio Access (E-UTRA); Base Station (BS) radio
transmission and reception '.
[11] 3GPP TS 36.355: 'Evolved Universal Terrestrial Radio Access (E-UTRA); LTE Positioning
Protocol (LPP)'
[12] 3GPP TS 36.455: 'Evolved Universal Terrestrial Radio Access (E-UTRA); LTE Positioning
Protocol A (LPPa)'
[13] 3GPP TS 36.459: 'Evolved Universal Terrestrial Radio Access (E-UTRA); SLm Application
Protocol (SLmAP)'
[14] 3GPP TS 36.111: 'Evolved Universal Terrestrial Radio Access (E-UTRA); Location Measurement
Unit (LMU) performance specification; Network Based Positioning Systems in E-UTRAN'

ETSI
3 Definitions, symbols and abbreviations
3.1 Definitions
For the purposes of the present document, the terms and definitions given in TR 21.905 [1] and the following apply. A
term defined in the present document takes precedence over the definition of the same term, if any, in TR 21.905 [1].
3.2 Symbols
For the purposes of the present document, the following symbols apply:
Ec/No Received energy per chip divided by the power density in the band
3.3 Abbreviations
For the purposes of the present document, the abbreviations given in TR 21.905 [1] and the following apply. An
abbreviation defined in the present document takes precedence over the definition of the same abbreviation, if any, in
TR 21.905 [1].
1x RTT CDMA2000 1x Radio Transmission Technology
CPICH Common Pilot Channel
E-SMLC Enhanced Serving Mobile Location Centre
E-UTRA Evolved UTRA
E-UTRAN Evolved UTRAN
FDD Frequency Division Duplex
GNSS Global Navigation Satellite System
GSM Global System for Mobile communication
HRPD CDMA2000 High Rate Packet Data
LMU Location Measurement Unit
P-CCPCH Primary Common Control Physical Channel
RSCP Received Signal Code Power
RSRP Reference Signal Received Power
RSRQ Reference Signal Received Quality
RSSI Received Signal Strength Indicator
RSTD Reference Signal Time Difference
SRS Sounding Reference Signal
TDD Time Division Duplex
UTRA Universal Terrestrial Radio Access
UTRAN Universal Terrestrial Radio Access Network
4 Control of UE/E-UTRAN measurements
In this chapter the general measurement control concept of the higher layers is briefly described to provide an
understanding on how L1 measurements are initiated and controlled by higher layers.
With the measurement specifications L1 provides measurement capabilities for the UE and E-UTRAN. These
measurements can be classified in different reported measurement types: intra-frequency, inter-frequency, inter-system,
traffic volume, quality and UE internal measurements (see the RRC Protocol [7]).
In the L1 measurement definitions, see chapter 5, the measurements are categorised as measurements in the UE (the
messages for these will be described in the MAC Protocol [6] or RRC Protocol [7] or LPP Protocol [11]) or
measurements in the E-UTRAN (the messages for these will be described in the Frame Protocol or LPPa Protocol [12]).

ETSI
To initiate a specific measurement, the E-UTRAN transmits a "RRC connection reconfiguration message' to the UE
including a measurement ID and type, a command (setup, modify, release), the measurement objects, the measurement
quantity, the reporting quantities and the reporting criteria (periodical/event-triggered), see [7] or E-SMLC transmits an
"LPP Request Location Information message" to UE, see [11].
When the reporting criteria are fulfilled the UE shall answer with a 'measurement report message' to the E-UTRAN
including the measurement ID and the results or an "LPP Provide Location Information message" to the E-SMLC, see
[11].
For idle mode, the measurement information elements are broadcast in the System Information.
5 Measurement capabilities for E-UTRA
In this chapter the physical layer measurements reported to higher layers are defined.
5.1 UE measurement capabilities
The structure of the table defining a UE measurement quantity is shown below.
Column field Comment
Definition Contains the definition of the measurement.
Applicable for States in which state(s) it shall be possible to perform this measurement. The following terms are
used in the tables:
RRC_IDLE;
RRC_CONNECTED;
Intra-frequency appended to the RRC state:
Shall be possible to perform in the corresponding RRC state on an intra-frequency cell;
Inter-frequency appended to the RRC state:
Shall be possible to perform in the corresponding RRC state on an inter-frequency cell
Inter-RAT appended to the RRC state:
Shall be possible to perform in the corresponding RRC state on an inter-RAT cell.
5.1.1 Reference Signal Received Power (RSRP)
Definition Reference signal received power (RSRP), is defined as the linear average over the power
contributions (in [W]) of the resource elements that carry cell-specific reference signals within the
considered measurement frequency bandwidth.
For RSRP determination the cell-specific reference signals R0 according TS 36.211 [3] shall be
used. If the UE can reliably detect that R1 is available it may use R1 in addition to R0 to determine
RSRP.
The reference point for the RSRP shall be the antenna connector of the UE.
If receiver diversity is in use by the UE, the reported value shall not be lower than the
corresponding RSRP of any of the individual diversity branches.
Applicable for RRC_IDLE intra-frequency,
RRC_IDLE inter-frequency,
RRC_CONNECTED intra-frequency,
RRC_CONNECTED inter-frequency
Note1: The number of resource elements within the considered measurement frequency bandwidth and within the
measurement period that are used by the UE to determine RSRP is left up to the UE implementation with the limitation
that corresponding measurement accuracy requirements have to be fulfilled.

ETSI
Note 2: The power per resource element is determined from the energy received during the useful part of the symbol,
excluding the CP.
5.1.2 Void
5.1.3 Reference Signal Received Quality (RSRQ)
Definition Reference Signal Received Quality (RSRQ) is defined as the ratio N×RSRP/(E-UTRA carrier
RSSI), where N is the number of RB"s of the E-UTRA carrier RSSI measurement bandwidth. The
measurements in the numerator and denominator shall be made over the same set of resource
blocks.
E-UTRA Carrier Received Signal Strength Indicator (RSSI), comprises the linear average of the
total received power (in [W]) observed only in OFDM symbols containing reference symbols for
antenna port 0, in the measurement bandwidth, over N number of resource blocks by the UE
from all sources, including co-channel serving and non-serving cells, adjacent channel
interference, thermal noise etc. If higher-layer signalling indicates certain subframes for
performing RSRQ measurements, then RSSI is measured over all OFDM symbols in the
indicated subframes.
The reference point for the RSRQ shall be the antenna connector of the UE.
If receiver diversity is in use by the UE, the reported value shall not be lower than the
corresponding RSRQ of any of the individual diversity branches.
Applicable for RRC_IDLE intra-frequency,
RRC_IDLE inter-frequency,
RRC_CONNECTED intra-frequency,
5.1.4 UTRA FDD CPICH RSCP
Definition Received Signal Code Power, the received power on one code measured on the Primary
CPICH. The reference point for the RSCP shall be the antenna connector of the UE. If Tx
diversity is applied on the Primary CPICH the received code power from each antenna shall be
separately measured and summed together in [W] to a total received code power on the Primary
CPICH. If receiver diversity is in use by the UE, the reported value shall not be lower than the
corresponding CPICH RSCP of any of the individual receive antenna branches.
Applicable for RRC_IDLE inter-RAT,
RRC_CONNECTED inter-RAT
5.1.5 UTRA FDD carrier RSSI
Definition The received wide band power, including thermal noise and noise generated in the receiver,
within the bandwidth defined by the receiver pulse shaping filter. The reference point for the
measurement shall be the antenna connector of the UE. If receiver diversity is in use by the UE,
the reported value shall not be lower than the corresponding UTRA carrier RSSI of any of the
individual receive antenna branches.

ETSI
5.1.6 UTRA FDD CPICH Ec/No
Definition The received energy per chip divided by the power density in the band. If receiver diversity is not
in use by the UE, the CPICH Ec/No is identical to CPICH RSCP/UTRA Carrier RSSI.
Measurement shall be performed on the Primary CPICH. The reference point for the CPICH
Ec/No shall be the antenna connector of the UE. If Tx diversity is applied on the Primary CPICH
the received energy per chip (Ec) from each antenna shall be separately measured and summed
together in [Ws] to a total received chip energy per chip on the Primary CPICH, before
calculating the Ec/No. If receiver diversity is in use by the UE, the measured CPICH Ec/No value
shall not be lower than the corresponding CPICH RSCPi/UTRA Carrier RSSIi of receive antenna
branch i .
5.1.7 GSM carrier RSSI
Definition Received Signal Strength Indicator, the wide-band received power within the relevant channel
bandwidth. Measurement shall be performed on a GSM BCCH carrier. The reference point for
the RSSI shall be the antenna connector of the UE.
5.1.8 UTRA TDD carrier RSSI
Definition The received wide band power, including thermal noise and noise generated in the receiver,
within the bandwidth defined by the receiver pulse shaping filter, for TDD within a specified
timeslot. The reference point for the measurement shall be the antenna connector of the UE.
5.1.9 UTRA TDD P-CCPCH RSCP
Definition Received Signal Code Power, the received power on P-CCPCH of a neighbour UTRA TDD cell.
The reference point for the RSCP shall be the antenna connector of the UE.
5.1.10 CDMA2000 1x RTT Pilot Strength
Definition CDMA2000 1x RTT Pilot Strength measurement is defined in section 2.6.6.2.2 of [8]

ETSI
5.1.11 CDMA2000 HRPD Pilot Strength
Definition CDMA2000 HRPD Pilot Strength Measurement is defined in section 8.7.6.1.2.3 of [9]
5.1.12 Reference signal time difference (RSTD)
Definition The relative timing difference between the neighbour cell j and the reference cell i, defined as
TSubframeRxj – TSubframeRxi, where: TSubframeRxj is the time when the UE receives the start of one
subframe from cell j TSubframeRxi is the time when the UE receives the corresponding start of one
subframe from cell i that is closest in time to the subframe received from cell j. The reference
point for the observed subframe time difference shall be the antenna connector of the UE.
Applicable for RRC_CONNECTED intra-frequency
5.1.13 UE GNSS Timing of Cell Frames for UE positioning
Definition The timing between cell j and a GNSS-specific reference time for a given GNSS (e.g.,
GPS/Galileo/Glonass system time). TUE-GNSS is defined as the time of occurrence of a specified
E-UTRAN event according to GNSS time for a given GNSS Id. The specified E-UTRAN event
is the beginning of a particular frame (identified through its SFN) in the first detected path (in
time) of the cell-specific reference signals of the cell j, where cell j is a cell chosen by the UE.
The reference point for TUE-GNSSj shall be the antenna connector of the UE.
5.1.14 UE GNSS code measurements
Definition The GNSS code phase (integer and fractional parts) of the spreading code of the i
th
GNSS
satellite signal. The reference point for the GNSS code phase shall be the antenna connector
of the UE.
Applicable for Void (this measurement is not related to E-UTRAN/UTRAN/GSM signals; its applicability is
therefore independent of the UE RRC state)
5.1.15 UE Rx – Tx time difference
Definition The UE Rx – Tx time difference is defined as TUE-RX – TUE-TX
Where:
TUE-RX is the UE received timing of downlink radio frame #i from the serving cell, defined by the
first detected path in time.
TUE-TX is the UE transmit timing of uplink radio frame #i.
The reference point for the UE Rx – Tx time difference measurement shall be the UE antenna
connector.

ETSI
5.2 E-UTRAN measurement abilities
The structure of the table defining a E-UTRAN measurement quantity is shown below.
Column field Comment
Definition Contains the definition of the measurement.
The term "antenna connector" used in this sub-clause to define the reference point for the E-UTRAN measurements
refers to the "BS antenna connector" test port A and test port B as described in [10]. The term "antenna connector"
refers to Rx or Tx antenna connector as described in the respective measurement definitions.
5.2.1 DL RS TX power
Definition Downlink reference signal transmit power is determined for a considered cell as the linear
average over the power contributions (in [W]) of the resource elements that carry cell-specific
reference signals which are transmitted by the eNode B within its operating system bandwidth.
For DL RS TX power determination the cell-specific reference signals R0 and if available R1
according TS 36.211 [3] can be used.
The reference point for the DL RS TX power measurement shall be the TX antenna connector.
5.2.2 Received Interference Power
Definition The uplink received interference power, including thermal noise, within one physical resource
block"s bandwidth of RB
scN resource elements as defined in TS 36.211 [3]. The reported value
shall contain a set of Received Interference Powers of physical resource blocks
1,...,0PRB −= UL
RBNn as defined in TS 36.211 [3]. The reference point for the measurement shall
be the RX antenna connector. In case of receiver diversity, the reported value shall be linear
average of the power in the diversity branches.
5.2.3 Thermal noise power
Definition
The uplink thermal noise power within the UL system bandwidth consisting of UL
RBN resource
blocks as defined in [3]. It is defined as (No x W), where No denotes the white noise power
spectral density on the uplink carrier frequency and fNNW RB
sc
UL
RB Δ⋅⋅= denotes the UL
system bandwidth. The measurement is optionally reported together with the Received
Interference Power measurement, it shall be determined over the same time period as the
Received Interference Power measurement, The reference point for the measurement shall be
the RX antenna connector. In case of receiver diversity, the reported value shall be linear
average of the power in the diversity branches.

ETSI
5.2.4 Timing advance (TADV)
Definition Type1:
Timing advance (TADV) type 1 is defined as the time difference
TADV = (eNB Rx – Tx time difference) + (UE Rx – Tx time difference),
where the eNB Rx – Tx time difference corresponds to the same UE that reports the UE Rx – Tx
time difference.
Type2:
Timing advance (TADV) type 2 is defined as the time difference
TADV = (eNB Rx – Tx time difference),
where the eNB Rx – Tx time difference corresponds to a received uplink radio frame containing
PRACH from the respective UE.
5.2.5 eNB Rx – Tx time difference
Definition The eNB Rx – Tx time difference is defined as T eNB-RX – TeNB-TX
Where:
T eNB-RX is the eNB received timing of uplink radio frame #i, defined by the first detected path in
time.
The reference point for TeNB-RX shall be the Rx antenna connector.
T eNB-TX is the eNB transmit timing of downlink radio frame #i.
The reference point for TeNB-TX shall be the Tx antenna connector.
5.2.6 E-UTRAN GNSS Timing of Cell Frames for UE positioning
Definition TE-UTRAN-GNSS is defined as the time of the occurrence of a specified LTE event according to a
GNSS-specific reference time for a given GNSS (e.g., GPS/Galileo/Glonass system time). The
specified LTE event is the beginning of the transmission of a particular frame (identified through
its SFN) in the cell. The reference point for TE-UTRAN-GNSS shall be the Tx antenna connector.
5.2.7 Angle of Arrival (AoA)
Definition AoA defines the estimated angle of a user with respect to a reference direction. The reference
direction for this measurement shall be the geographical North, positive in a counter-clockwise
direction.
The AoA is determined at the eNB antenna for an UL channel corresponding to this UE.

ETSI
5.2.8 UL Relative Time of Arrival (TUL-RTOA)
Definition The UL Relative Time of Arrival (TUL-RTOA) is the beginning of subframe i containing SRS received
in LMU j, relative to the configurable reference time [13], [14]. The reference point [14] for the UL
relative time of arrival shall be the RX antenna connector of the LMU node when LMU has a
separate RX antenna or shares RX antenna with eNB and the eNB antenna connector when
LMU is integrated in eNB.

ETSI
Annex A (informative):
Change history
Change history
Date TSG # TSG Doc. CR Rev Subject/Comment Old New
02/10/06 - - - Draft version created - 0.0.0
11/10/06 - - - Minor editorial updates for RAN1#46bis 0.0.0 0.0.1
13/10/06 - - - Endorsed skeleton 0.0.1 0.1.0
27/02/07 - - - Update after 3GPP TSG RAN WG1 #48 0.1.0 0.1.1
05/03/07 - - - RAN1 endorsed version 0.1.1 0.2.0
03/05/07 - - - Update after 3GPP TSG RAN WG1#48bis 0.2.0 0.2.1
08/03/07 - - - RAN WG1#49 endorsed version 0.2.1 0.3.0
31/05/07 RAN#36 RP-070490 - Presented for information at RAN#36 0.3.0 1.0.0
21/06/07 - - - Update after 3GPP TSG RAN #36 1.0.0 1.0.1
25/06/07 - - - 3GPP TSG RAN WG1#49bis endorsed version 1.0.1 1.1.0
17/08/07 - - - Update after 3GPP TSG RAN WG1#48bis 1.1.0 1.1.1
20/08/07 - - - 3GPP TSG RAN WG1#50 endorsed version 1.1.1 1.2.0
10/09/07 RAN#37 RP-070732 - For approval at RAN#37 1.2.0 2.0.0
12/09/07 RAN_37 RP-070732 - - Approved version 2.0.0 8.0.0
28/11/07 RAN_38 RP-070949 0001 1 RRC state correction for LTE UE measurements 8.0.0 8.1.0
05/03/08 RAN_39 RP-080145 0003 1 Inclusion of agreements from RAN1#51bis and RAN1#52 8.1.0 8.2.0
28/05/08 RAN_40 RP-080435 0004 - Introduction of eNode B Measurement of Received Interference
Power
8.2.0 8.3.0
28/05/08 RAN_40 RP-080435 0005 - Introduction of eNode B Measurement of Thermal Noise Power 8.2.0 8.3.0
09/09/08 RAN_41 RP-080671 0006 - Modification to the RSRP definition 8.3.0 8.4.0
09/09/08 RAN_41 RP-080671 0007 - Modification of RSRQ definition and removal of RSSI 8.3.0 8.4.0
03/12/08 RAN_42 RP-080985 0008 - RSRQ Measurement Definition 8.4.0 8.5.0
04/03/09 RAN_43 RP-090237 0009 - RSRP and RSRQ Definitions with Receiver Diversity 8.5.0 8.6.0
15/09/09 RAN_45 RP-090888 0010 Clarification on reference point of RSRP and RSRQ for
EUTRA
8.6.0 8.7.0
01/12/09 RAN_46 RP-091172 0011 1 Introduction of LTE positioning 8.7.0 9.0.0
16/03/10 RAN_47 RP-100205 0012 1 Modification of RSRQ definition 9.0.0 9.1.0
01/06/10 RAN_48 RP-100590 0014 - On alignment of RAN1/2 positioning specification 9.1.0 9.2.0
01/06/10 RAN_48 RP-100590 0015 1 Clarification of RSTD measurement 9.1.0 9.2.0
07/12/10 RAN_50 - - - Creation of Rel-10 specification 9.2.0 10.0.0
15/03/11 RAN_51 RP-110258 0016 - RSRQ Measurement with ABS 10.0.0 10.1.0
04/09/12 RAN_57 RP-121273 0018 4 UL Relative Time of Arrival 10.1.0 11.0.0

ETSI
History
Document history
V11.0.0 October 2012 Publication

Lte 3 gpp

More Related Content

Similar to Lte 3 gpp (20)

More from Jose Asuncion Silva Vasquez (20)

Recently uploaded (20)

Lte 3 gpp