Make electronics learning_by_dis

Make: Electronics
Learning by Discovery
Charles Platt
with photographs and illustrations by the author
Beijing • Cambridge • Farnham • Köln • Sebastopol • Taipei • Tokyo

Make: Electronics
by Charles Platt
Copyright © Helpful Corporation. All rights reserved.
Printed in Canada.
Published by O’Reilly Media, Inc., 1005 Gravenstein Highway North, Sebastopol, CA 95472.
O’Reilly Media books may be purchased for educational, business, or sales promotional use. Online editions are also avail-
able for most titles (my.safaribooksonline.com). For more information, contact our corporate/institutional sales department:
800-998-9938 or corporate@oreilly.com.
Editors: Dale Dougherty and Brian Jepson
Development Editor: Gareth Branwyn
Production Editor: Rachel Monaghan
Technical Editor: Andrew“Bunnie”Huang
Copyeditor: Nancy Kotary
Proofreader: Nancy Reinhardt
Indexer: Julie Hawks
Cover Designer: Mark Paglietti
Interior Designer: Ron Bilodeau
Illustrator/Photographer: Charles Platt
Cover Photographer: Marc de Vinck
Print History:
December 2009: First Edition.
The O’Reilly logo is a registered trademark of O’Reilly Media, Inc. Many of the designations used by manufacturers and
sellers to distinguish their products are claimed as trademarks. Where those designations appear in this book, and O’Reilly
Media, Inc., was aware of a trademark claim, the designations have been printed in caps or initial caps.
While every precaution has been taken in the preparation of this book, the publisher and author assume no responsibility
for errors or omissions, or for damages resulting from the use of the information contained herein.
ISBN: 978-0-596-15374-8
[TI]

vii
Preface.. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ix
1. Experiencing Electricity.. . . . . . . . . . . . . . . . . . . . . 1
Shopping List: Experiments 1 Through 5 .. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Experiment 1: Taste the Power!.. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Experiment 2: Let’s Abuse a Battery!.. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Experiment 3: Your First Circuit.. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Experiment 4: Varying the Voltage.. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Experiment 5: Let’s Make a Battery.. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
2. Switching Basics and More.. . . . . . . . . . . . . . . . 39
Shopping List: Experiments 6 Through 11.. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Experiment 6: Very Simple Switching.. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Experiment 7: Relay-Driven LEDs.. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
Experiment 8: A Relay Oscillator.. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
Experiment 9: Time and Capacitors.. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68
Experiment 10: Transistor Switching.. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73
Experiment 11: A Modular Project.. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82
3. Getting Somewhat More Serious.. . . . . . . . . 95
Shopping List: Experiments 12 Through 15.. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95
Experiment 12: Joining Two Wires Together.. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 104
Experiment 13: Broil an LED.. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 114
Experiment 14: A Pulsing Glow.. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 117
Experiment 15: Intrusion Alarm Revisited.. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 127
Contents

Contentsviii
4. Chips, Ahoy!.. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 147
Shopping List: Experiments 16 Through 24.. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 147
Experiment 16: Emitting a Pulse.. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 153
Experiment 17: Set Your Tone.. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 162
Experiment 18: Reaction Timer.. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 170
Experiment 19: Learning Logic.. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 181
Experiment 20: A Powerful Combination.. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 197
Experiment 21: Race to Place.. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 205
Experiment 22: Flipping and Bouncing.. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 211
Experiment 23: Nice Dice.. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 214
Experiment 24: Intrusion Alarm Completed.. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 223
5. What Next?.. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 227
Shopping List: Experiments 25 Through 36.. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 228
Customizing Your Work Area.. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 228
Reference Sources.. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 233
Experiment 25: Magnetism.. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 236
Experiment 26: Tabletop Power Generation.. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 239
Experiment 27: Loudspeaker Destruction.. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 242
Experiment 28: Making a Coil React.. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 246
Experiment 29: Filtering Frequencies . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 249
Experiment 30: Fuzz.. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 257
Experiment 31: One Radio, No Solder,
No Power.. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 262
Experiment 32: A Little Robot Cart.. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 268
Experiment 33: Moving in Steps.. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 284
Experiment 34: Hardware Meets Software.. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 293
Experiment 35: Checking the Real World.. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 306
Experiment 36: The Lock, Revisited.. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 311
In Closing.. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 317
Appendix. Online Retail Sources and Manufac-
turers.. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 319
Index.. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 325

ix
Preface
How to Have Fun with This Book
Everyone uses electronic devices, but most of us don’t really know what goes
on inside them.
Of course, you may feel that you don’t need to know. If you can drive a car
without understanding the workings of an internal combustion engine, pre-
sumably you can use an iPod without knowing anything about integrated cir-
cuits. However, understanding some basics about electricity and electronics
can be worthwhile for three reasons:
• By learning how technology works, you become better able to control
your world instead of being controlled by it. When you run into problems,
you can solve them instead of feeling frustrated by them.
• Learning about electronics can be fun—so long as you approach the pro-
cess in the right way.The tools are relatively cheap, you can do all the work
on a tabletop, and it doesn’t consume a lot of time (unless you want it to).
• Knowledge of electronics can enhance your value as an employee or per-
haps even lead to a whole new career.
Learning by Discovery
Most introductory guides begin with definitions and facts, and gradually get
to the point where you can follow instructions to build a simple circuit.
This book works the other way around. I want you to start putting components
together right away. After you see what happens, you’ll figure out what’s go-
ing on. I believe this process of learning by discovery creates a more powerful
and lasting experience.

How Hard Will It Be?
Prefacex
Learning by discovery occurs in serious research, when scientists notice an un-
usual phenomenon that cannot be explained by current theory, and they start
to investigate it in an effort to explain it. This may ultimately lead to a better
understanding of the world.
We’re going to be doing the same thing, although obviously on a much less
ambitious level.
Along the way, you will make some mistakes. This is good. Mistakes are the
best of all learning processes. I want you to burn things out and mess things
up, because this is how you learn the limits of components and materials.
Since we’ll be using low voltages, there’ll be no chance of electrocution, and
so long as you limit the flow of current in the ways I’ll describe, there will be no
risk of burning your fingers or starting fires.
Figure P-1. Learning by discovery allows you to start building simple circuits right away,
using a handful of cheap components, a few batteries, and some alligator clips.
How Hard Will It Be?
I assume that you’re beginning with no prior knowledge of electronics. So,
the first few experiments will be ultra-simple, and you won’t even use solder
or prototyping boards to build a circuit. You’ll be holding wires together with
alligator clips.
Very quickly, though, you’ll be experimenting with transistors, and by the end
of Chapter 2, you will have a working circuit that has useful applications.
I don’t believe that hobby electronics has to be difficult to understand. Of
course, if you want to study electronics more formally and do your own circuit
design, this can be challenging. But in this book, the tools and supplies will be
inexpensive, the objectives will be clearly defined, and the only math you’ll
need will be addition, subtraction, multiplication, division, and the ability to
move decimal points from one position to another.
StayWithin the Limits!
Although I believe that everything
suggested in this book is safe, I’m as-
suming that you will stay within the
limits that I suggest. Please always
follow the instructions and pay
attention to the warnings, denoted
by the icon you see here. If you go
beyond the limits, you will expose
yourself to unnecessary risks.

Preface xi
Fundamentals
Moving Through This Book
Basically there are two ways to present information in a book of this kind: in
tutorials and in reference sections. I’m going to use both of these methods.
You’ll find the tutorials in sections headed as follows:
• Shopping Lists
• Using Tools
• Experiments
You’ll find reference sections under the following headings:
• Fundamentals
• Theory
• Background
How you use the sections is up to you. You can skip many of the reference
sections and come back to them later. But if you skip many of the tutorials,
this book won’t be of much use to you. Learning by discovery means that you
absolutely, positively have to do some hands-on work, and this in turn means
that you have to buy some basic components and play with them. You will
gain very little by merely imagining that you are doing this.
It’s easy and inexpensive to buy what you need. In almost any urban or sub-
urban area in the United States, chances are you live near a store that sells
electronic components and some basic tools to work with them. I am referring,
of course, to RadioShack franchises. Some Shacks have more components than
others, but almost all of them have the basics that you’ll need.
You can also visit auto supply stores such as AutoZone and Pep Boys for basics
such as hookup wire, fuses, and switches, while stores such as Ace Hardware,
Home Depot, and Lowe’s will sell you tools.
If you prefer to buy via mail order, you can easily find everything you need by
searching online. In each section of the book, I’ll include the URLs of the most
popular supply sources, and you’ll find a complete list of URLs in the appendix.
Fundamentals
Mail-ordering components and tools
Here are the primary mail-order sources that I use myself online:
http://www.radioshack.com
RadioShack, a.k.a. The Shack. For tools and components. Not always the
cheapest, but the site is easy and convenient, and some of the tools are
exactly what you need.
http://www.mouser.com
Mouser Electronics.
http://www.digikey.com
Digi-Key Corporation.

Fundamentals
Prefacexii
http://www.newark.com
Newark.
Mouser, Digi-Key, and Newark are all good sources for components, usually
requiring no minimum quantities.
http://www.allelectronics.com
All Electronics Corporation. A narrower range of components, but specifi-
cally aimed at the hobbyist, with kits available.
http://www.ebay.com
You can find surplus parts and bargains here, but you may have to try
several eBay Stores to get what you want. Those based in Hong Kong are
often very cheap, and I’ve found that they are reliable.
http://www.mcmaster.com
McMaster-Carr. Especially useful for high-quality tools.
Lowe’s and Home Depot also allow you to shop online.
Figure P-2. You’ll find no shortage of parts, tools, kits, and gadgets online.

Preface xiii
Safari® Books Online
Companion Kits
Maker Shed (www.makershed.com) offers a
number of Make: Electronics companion kits,
both toolkits and bundles of the various
components used in the book’s experi-
ments. This is a simple, convenient, and cost-effective way of getting all the
tools and materials you need to do the projects in this book.
Comments and Questions
Please address comments and questions concerning this book to the publisher:
O’Reilly Media, Inc.
1005 Gravenstein Highway North
Sebastopol, CA 95472
800-998-9938 (in the United States or Canada)
707-829-0515 (international or local)
707-829-0104 (fax)
We have a web page for this book, where we list errata, examples, larger ver-
sions of the book’s figures, and any additional information. You can access this
page at:
http://oreilly.com/catalog/9780596153748
To comment or ask technical questions about this book, send email to:
bookquestions@oreilly.com
For more information about our books, conferences, Resource Centers, and
the O’Reilly Network, see our website at:
http://oreilly.com
Safari®
Books Online
Safari Books Online is an on-demand digital library that
lets you easily search over 7,500 technology and creative
reference books and videos to find the answers you
need quickly.
With a subscription, you can read any page and watch any video from our
library online. Read books on your cell phone and mobile devices. Access new
titles before they are available for print, and get exclusive access to manu-
scripts in development and post feedback for the authors. Copy and paste
code samples, organize your favorites, download chapters, bookmark key sec-
tions, create notes, print out pages, and benefit from tons of other time-saving
features.
O’Reilly Media has uploaded this book to the Safari Books Online service. To
have full digital access to this book and others on similar topics from O’Reilly
and other publishers, sign up for free at http://my.safaribooksonline.com.

1
1
Experiencing Electricity
I want you to get a taste for electricity—literally!—in the first experiment. This
first chapter of the book will show you:
• How to understand and measure electricity and resistance
• How to handle and connect components without overloading, damaging,
or destroying them
Even if you have some prior knowledge of electronics, you should try these
experiments before you venture on to the rest of the book.
Shopping List: Experiments 1 Through 5
If you want to limit your number of shopping trips or online purchases, look
ahead in the book for additional shopping lists, and combine them to make
one bulk purchase.
In this first chapter, I will give you part numbers and sources for every tool and
component that we’ll be using. Subsequently, I won’t expect you to need such
specific information, because you will have gained experience searching for
items on your own.
Tools
Small pliers
RadioShack Kronus 4.5-inch, part number 64-2953 or Xcelite 4-inch mini
long-nose pliers, model L4G.
Or similar. See Figures 1-1 through 1-3. Look for these tools in hardware
stores and the sources listed in the preface. The brand is unimportant.
After you use them for a while, you’ll develop your own preferences. In
particular, you have to decide whether you like spring-loaded handles. If
you decide you don’t, you’ll need a second pair of pliers to pull the springs
out of the first.
Maker Shed (www.makershed.com)
has put together a series of Make:
Electronics companion kits. These in-
clude all of the tools and components
used in book’s experiments. This is a
quick, simple, and cost-effective way
of getting everything you need to
complete the projects in this book.
In this chapter
Experiment 1: Taste the Power!
Experiment 2: Let’s Abuse a Battery!
Experiment 3: Your First Circuit
Experiment 4: Varying the Voltage
Experiment 5: Let’s Make a Battery

Chapter 12
Wire cutters
RadioShack Kronus 4.5-inch, part number 64-2951, or Stanley 7-inch
model 84-108.
Or similar. Use them for cutting copper wire, not harder metals (Figure 1-4).
Figure 1-1. Generic long-nosed
pliers are your most fundamen-
tal tool for gripping, bending,
and picking things up after you
drop them.
Figure 1-2. Longer-nosed pliers:
these are useful for reaching into
tiny spaces.
Figure 1-3. Sharp-pointed pliers
are designed for making jewelry,
but are also useful for grabbing
tiny components.
Figure 1-4. Wire cutters, some-
times known as side cutters, are
essential.
Multimeter
Extech model EX410 or BK Precision model 2704-B or Amprobe model
5XP-A.
Or similar. Because electricity is invisible, we need a tool to visualize the
pressure and flow, and a meter is the only way. A cheap meter will be suf-
ficient for your initial experiments. If you buy online, try to check customer
reviews, because reliability may be a problem for cheap meters. You can
shop around for retailers offering the best price. Don’t forget to search on
eBay.
The meter must be digital—don’t get the old-fashioned analog kind with
a needle that moves across a set of printed scales. This book assumes that
you are looking at a digital display.
I suggest that you do not buy an autoranging meter.“Autoranging”sounds
useful—for example, when you want to check a 9-volt battery, the meter
figures out for itself that you are not trying to measure hundreds of volts,
nor fractions of a volt. The trouble is that this can trick you into making
errors. What if the battery is almost dead? Then you may be measuring
a fraction of a volt without realizing it. The only indication will be an eas-
ily overlooked “m” for “millivolts” beside the large numerals of the meter
display.

Experiencing Electricity 3
On a manual-ranging meter, you select the range, and if the source that
you are measuring is outside of that range, the meter tells you that you
made an error. I prefer this. I also get impatient with the time it takes for
the autoranging feature to figure out the appropriate range each time I
make a measurement. But it’s a matter of personal preference. See Figures
1-5 through 1-7 for some examples of multimeters.
Figure 1-5. You can see by the wear and
tear that this is my own favorite meter.
It has all the necessary basic features
and can also measure capacitance (the
F section, for Farads). It can also check
transistors. You have to choose the ranges
manually.
Figure 1-6. Mid-priced RadioShack meter,
which has the basic features; however,
the dual purpose for each dial position,
selected with the SELECT button, may be
confusing. This is an autoranging meter.
Figure 1-7. An autoranging meter from
Extech offers basic functions, plus a tem-
perature probe, which may be useful to
check whether components such as power
supplies are running unduly hot.
Supplies
Batteries
9-volt battery. Quantity: 1.
AA batteries, 1.5 volts each. Quantity: 6.
The batteries should be disposable alkaline, the cheapest available, be-
cause we may destroy some of them. You should absolutely not use re-
chargeable batteries in Experiments 1 and 2.
Battery holders and connectors
Snap connector for 9-volt battery, with wires attached (Figure 1-8).
Quantity: 1. RadioShack part number 270-325 or similar. Any snap con-
nector that has wires attached will do.
Battery holder for single AA cell, with wires attached (Figure 1-9). Quan-
tity: 1. RadioShack part number 270-401 or Mouser.com catalog number
12BH410-GR, or similar; any single-battery holder that has thin wires at-
tached will do.
Figure 1-8. Snap connector for a 9-volt
battery.
Figure 1-9. Single AA-sized battery carrier
with wires.

Chapter 14
Battery holder for four AA cells, with wires attached (Figure 1-10). Quan-
tity: 1. All Electronics catalog number BH-342 or RadioShack part 270-391
or similar.
Alligator clips
Vinyl-insulated. Quantity: at least 6. All Electronics catalog number ALG-28
or RadioShack part number 270-1545 or similar (Figure 1-11).
Components
You may not know what some of these items are, or what they do. Just look
for the part numbers and descriptions, and match them with the photographs
shownhere.Veryquickly,inthelearningbydiscoveryprocess,allwillberevealed.
Fuses
Automotive-style, mini-blade type, 3 amps. Quantity: 3. RadioShack part
number 270-1089, or Bussmann part ATM-3, available from automotive
parts suppliers such as AutoZone (Figure 1-12).
Or similar. A blade-type fuse is easier to grip with alligator clips than a
round cartridge fuse.
Potentiometers
Panel-mount, single-turn, 2K linear, 0.1 watt minimum. Quantity: 2. Alpha
part RV170F-10-15R1-B23 or BI Technologies part P160KNPD-2QC25B2K,
from Mouser.com or other component suppliers (Figure 1-13).
Or similar. The “watt” rating tells you how much power this component
can handle. You don’t need more than 0.5 watts.
Resistors
Assortment 1/4-watt minimum, various values but must include 470 ohms,
1K, and 2K or 2.2K. Quantity: at least 100. RadioShack part number 271-312.
Or search eBay for“resistor assorted.”
Light-emitting diodes (LEDs)
Any size or color (Figures 1-14 and 1-15). Quantity: 10. RadioShack part num-
ber 276-1622 or All Spectrum Electronics part K/LED1 from Mouser.com.
Or similar. Just about any LEDs will do for these first experiments.
Figure 1-14. Typical 5-mm diameter light-
emitting diode (LED).
Figure 1-15. Jumbo-sized LED (1 cm
diameter) is not necessarily brighter or
more expensive. For most of the experi-
ments in this book, buy whatever LEDs
you like the look of.
Figure 1-10. Battery carrier for four AA
cells, to be installed in series, delivering 6
volts.
Figure 1-11. Alligator clips inside vinyl
sheaths, which reduce the chance of ac-
cidental short circuits.
Figure 1-12. A 3-amp fuse intended primar-
ily for automotive use, shown here larger
than actual size.
Figure 1-13. Potentiometers come in many
shapes and sizes, with different lengths of
shafts intended for different types of knobs.
For our purposes, any style will do, but the
larger-sized ones are easier to play with.

Can you taste electricity? Maybe not, but it feels as if you can.
You will need:
• 9-volt battery
• Snap connector for battery terminals
• Multimeter
Procedure
Moisten your tongue and touch the tip of it to the metal terminals of a 9-volt
battery. The sudden sharp tingle that you feel is caused by electricity flowing
from one terminal of the battery (Figure 1-16), through the moisture on and
in your tongue, to the other terminal. Because the skin of your tongue is very
thin (it’s actually a mucus membrane) and the nerves are close to the surface,
you can feel the electricity very easily.
Now stick out your tongue, dry the tip of it very thoroughly with a tissue, and
repeat the experiment without allowing your tongue to become moist again.
You should feel less of a tingle.
What’s happening here? We’re going to need a meter to find out.
Tools
Setting up your meter
Check the instructions that came with the meter to find out whether you have
to install a battery in it, or whether a battery is preinstalled.
Most meters have removable wires, known as leads (pronounced “leeds”).
Most meters also have three sockets on the front, the leftmost one usually be-
ing reserved to measure high electrical currents (flows of electricity). We can
ignore that one for now.
The leads will probably be black and red. The black wire plugs into a socket
labeled “COM” or “Common.” Plug the red one into the socket labeled “V” or
“volts.”See Figures 1-17 through 1-20.
The other ends of the leads terminate in metal spikes known as probes, which
you will be touching to components when you want to make electrical mea-
surements.The probes detect electricity; they don’t emit it in significant quan-
tities. Therefore, they cannot hurt you unless you poke yourself with their
sharp ends.
If your meter doesn’t do autoranging, each position on the dial will have a
number beside it. This number means “no higher than.” For instance if you
want to check a 6-volt battery, and one position on the voltage section of the
dial is numbered 2 and the next position is numbered 20, position 2 means
“no higher than 2 volts.”You have to go to the next position, which means“no
higher than 20 volts.”
No MoreThan 9Volts
A 9-volt battery won’t hurt you. But
do not try this experiment with a
higher-voltage battery or a larger
battery that can deliver more cur-
rent. Also, if you have metal braces
on your teeth, be very careful not to
touch them with the battery.
Figure 1-16. Step 1 in the process of learn-
ing by discovery: the 9-volt tongue test.
Figure 1-17. The black lead plugs into
the Common (COM) socket, and the
red lead plugs into the red socket that’s
almost always on the righthand side of a
multimeter.

Chapter 16
If you make a mistake and try to measure something inappropriate, the meter
will show you an error message such as“E”or“L.”Turn the dial and try again.
Figure 1-18 Figure 1-19 Figure 1-20. To measure resistance and
voltage, plug the black lead into the Com-
mon socket and the red lead into the Volts
socket. Almost all meters have a separate
socket where you must plug the red lead
when you measure large currents in amps,
but we’ll be dealing with this later.
Fundamentals
Ohms
We measure distance in miles or kilometers, weight in pounds
or kilograms, temperature in Fahrenheit or Centigrade—and
electrical resistance in ohms. The ohm is an international unit.
The Greek omega symbol (Ω) is used to indicate ohms, as
shown in Figures 1-21 and 1-22. Letter K (or alternatively,
KΩ) means a kilohm, which is 1,000 ohms. Letter M (or MΩ)
means a megohm, which is 1,000,000 ohms.
Number of
ohms
Usually
expressed as
Abbreviated as
1,000 ohms 1 kilohm 1KΩ or 1K
10,000 ohms 10 kilohms 10KΩ or 10K
100,000 ohms 100 kilohms 100KΩ or 100K
1,000,000 ohms 1 megohm 1MΩ or 1M
10,000,000 ohms 10 megohms 10MΩ or 10M
A material that has very high resistance to electricity is
known as an insulator. Most plastics, including the colored
sheaths around wires, are insulators.
A material with very low resistance is a conductor. Metals
such as copper, aluminum, silver, and gold are excellent
conductors.
Figure 1-21. The omega
symbol is used inter-
nationally to indicate
resistance on ohms.
Figure 1-22. You’ll find it printed
or written in a wide variety of
styles.

Procedure
We’re going to use the meter to discover the electrical resistance of your
tongue. First, set your meter to measure resistance. If it has autoranging, look
to see whether it is displaying a K, meaning kilohms, or M, meaning megohms.
If you have to set the range manually, begin with no less than 100,000 ohms
(100K). See Figures 1-23 through 1-25.
Touch the probes to your tongue, about an inch apart. Note the reading,
which should be around 50K. Now put aside the probes, stick out your tongue,
and use a tissue to dry it very carefully and thoroughly. Without allowing your
tongue to become moist again, repeat the test, and the reading should be
higher. Finally, press the probes against the skin of your hand or arm: you may
get no reading at all, until you moisten your skin.
When your skin is moist (for instance, if you perspire), its electrical resistance de-
creases. This principle is used in lie detectors, because someone who knowingly tells
a lie, under conditions of stress, tends to perspire.
A 9-volt battery contains chemicals that liberate electrons (particles of electric-
ity), which want to flow from one terminal to the other as a result of a chemical
reaction inside it. Think of the cells inside a battery as being like two water
tanks—one of them full, the other empty. If they are connected with a pipe,
water flows between them until their levels are equal. Figure 1-26 may help
you visualize this. Similarly, when you open up an electrical pathway between
the two sides of a battery, electrons flow between them, even if the pathway
consists only of the moisture on your tongue.
Electrons flow more easily through some substances (such as a moist tongue)
than others (such as a dry tongue).
Figure 1-26. Think of the cells in a battery as being like two cylinders: one full of water, the
other empty. Open a connection between the cylinders, and the water will flow until the
levels are equal on both sides. The less resistance in the connection, the faster the flow
will be.
Figure 1-23
Figure 1-24
Figure 1-25. To measure ohms, turn the
dial to the ohm (omega) symbol. On an
autoranging meter, you can then press
the Range button repeatedly to display
different ranges of resistance, or simply
touch the probes to a resistance and wait
for the meter to choose a range auto-
matically. A manual meter requires you to
select the range with the dial (you should
set it to 100K or higher, to measure skin
resistance). If you don’t get a meaningful
reading, try a different range.

Chapter 18
Background
The man who discovered resistance
Georg Simon Ohm, pictured in Figure
1-27, was born in Bavaria in 1787 and
worked in obscurity for much of his
life, studying the nature of electricity
using metal wire that he had to make
for himself (you couldn’t truck on
down to Home Depot for a spool of
hookup wire back in the early 1800s).
Despite his limited resources and in-
adequate mathematical abilities, Ohm
was able to demonstrate in 1827 that
the electrical resistance of a conduc-
tor such as copper varied in propor-
tion with its area of cross-section,
and the current flowing through it is
proportional to the voltage applied to
it, as long as temperature is held con-
stant. Fourteen years later, the Royal
Society in London finally recognized
the significance of his contribution
and awarded him the Copley Medal.
Today, his discovery is known as
Ohm’s Law.
Figure 1-27. Georg Simon Ohm, after
being honored for his pioneering work,
most of which he pursued in relative
obscurity.
Further Investigation
Attach the snap-on terminal cap (shown earlier in Figure 1-8) to the 9-volt bat-
tery.Take the two wires that are attached to the cap and hold them so that the
bare ends are just a few millimeters apart. Touch them to your tongue. Now
separate the ends of the wires by a couple of inches, and touch them to your
tongue again. (See Figure 1-28.) Notice any difference?
Use your meter to measure the electrical resistance of your tongue, this time
varying the distance between the two probes.When electricity travels through
a shorter distance, it encounters less total resistance. As a result, the current
(the flow of electricity per second) increases. You can try a similar experiment
on your arm, as shown in Figure 1-29.
Use your meter to test the electrical resistance of water. Dissolve some salt in
the water, and test it again. Now try measuring the resistance of distilled water
(in a clean glass).
The world around you is full of materials that conduct electricity with varying
amounts of resistance.
Figure 1-28. Modifying the tongue test to
show that a shorter distance, with lower
resistance, allows greater flow of electric-
ity, and a bigger zap.
Figure 1-29. Moisten your skin before trying
to measure its resistance. You should find
that the resistance goes up as you move
the meter probes farther apart. The resis-
tance is proportional to the distance.

Cleanup and Recycling
Your battery should not have been damaged or significantly discharged by
this experiment. You’ll be able to use it again.
Remember to switch off your meter before putting it away.
To get a better feeling for electrical power, you’re going to do what most books
tell you not to do. You’re going to short out a battery. A short circuit is a direct
connection between the two sides of a power source.
Short Circuits
Short circuits can be dangerous. Do not short out a power outlet in your home:
there’ll be a loud bang, a bright flash, and the wire or tool that you use will be par-
tially melted, while flying particles of melted metal can burn you or blind you.
If you short out a car battery, the flow of current is so huge that the battery might
even explode, drenching you in acid (Figure 1-30).
Lithium batteries are also dangerous. Never short-circuit a lithium battery: it can
catch fire and burn you (Figure 1-31).
Use only an alkaline battery in this experiment, and only a single AA cell (Figure
1-32). You should also wear safety glasses in case you happen to have a defective
battery.
You will need:
• 1.5-volt AA battery
• Single-battery carrier
• 3-amp fuse
• Safety glasses (regular eyeglasses or sunglasses will do)
Procedure
Use an alkaline battery. Do not use any kind of rechargeable battery.
Put the battery into a battery holder that’s designed for a single battery and
has two thin insulated wires emerging from it, as shown in Figure 1-32. Do not
use any other kind of battery holder.
Use an alligator clip to connect the bare ends of the wires, as shown in Figure
1-32. There will be no spark, because you are using only 1.5 volts. Wait one
minute, and you’ll find that the wires are getting hot.Wait another minute, and
the battery, too, will be hot.
Figure 1-30. Anyone who has dropped an
adjustable wrench across the bare termi-
nals of a car battery will tell you that short
circuits can be dramatic at a “mere” 12
volts, if the battery is big enough.
Figure 1-31. The low internal resistance of
lithium batteries (which are often used in
laptop computers) allows high currents to
flow, with unexpected results. Never fool
around with lithium batteries!
Figure 1-32. Shorting out an alkaline bat-
tery can be safe if you follow the directions
precisely. Even so, the battery is liable to
become too hot to touch comfortably.
Don’t try this with any type of recharge-
able battery.

Chapter 110
The heat is caused by electricity flowing through the wires and through the
electrolyte (the conductive fluid) inside the battery. If you’ve ever used a hand
pump to force air into a bicycle tire, you know that the pump gets warm. Elec-
tricity behaves in much the same way. You can imagine the electricity being
composed of particles (electrons) that make the wire hot as they push through
it. This isn’t a perfect analogy, but it’s close enough for our purposes.
Chemical reactions inside the battery create electrical pressure. The correct
name for this pressure is voltage, which is measured in volts and is named after
Alessandro Volta, an electrical pioneer.
Going back to the water analogy: the height of the water in a tank is propor-
tionate to the pressure of the water, and comparable to voltage. Figure 1-33
may help you to visualize this.
But volts are only half of the story. When electrons flow through a wire, the
flow is known as amperage, named after yet another electrical pioneer, André-
Marie Ampère. The flow is also generally known as current. It’s the current—
the amperage—that generates the heat.
Background
Why didn’t your tongue get hot?
When you touched the 9-volt battery to your tongue, you felt a tingle, but no
perceptible heat. When you shorted out a battery, you generated a noticeable
amount of heat, even though you used a lower voltage. How can we explain
this?
The electrical resistance of your tongue is very high, which reduces the flow of
electrons. The resistance of a wire is very low, so if there’s only a wire connect-
ing the two terminals of the battery, more current will pass through it, creating
more heat. If all other factors remain constant:
• Lower resistance allows more current to flow (Figure 1-34).
• The heat generated by electricity is proportional to the amount of electric-
ity (the current) that flows.
Here are some other basic concepts:
• The flow of electricity per second is measured in amperes, or amps.
• The pressure of electricity causes the flow, measured in volts.
• The resistance to the flow is measured in ohms.
• A higher resistance restricts the current.
• A higher voltage overcomes resistance and increases the current.
Figure 1-34. Larger resistance results in
smaller flow—but if you increase the pres-
sure, it may overcome the resistance and
increase the flow.
If you’re wondering exactly how much current flows between the terminals
of a battery when you short it out, that’s a difficult question to answer. If you
try to use your multimeter to measure it, you’re liable to blow the fuse inside
the meter. Still, you can use your very own 3-amp fuse, which we can sacrifice
because it didn’t cost very much.
Water level
Amperage
(flow)
Resistance
Voltage
(pressure)
Figure 1-33. Think of voltage as pressure,
and amperes as flow.

First inspect the fuse very carefully, using a magnifying glass if you have one.
You should see a tiny S-shape in the transparent window at the center of the
fuse. That S is a thin section of metal that melts easily.
Remove the battery that you short-circuited. It is no longer useful for anything,
and should be recycled if possible. Put a fresh battery into the battery carrier,
connect the fuse as shown in Figure 1-35, and take another look. You should
see a break in the center of the S shape, where the metal melted almost in-
stantly. Figure 1-36 shows the fuse before you connected it, and Figure 1-37
depicts a blown fuse. This is how a fuse works: it melts to protect the rest of
the circuit.That tiny break inside the fuse stops any more current from flowing.
Fundamentals
Volt basics
Electrical pressure is measured in volts. The volt is an international unit. A millivolt
is 1/1,000 of a volt.
Number of volts Usually expressed as Abbreviated as
0.001 volts 1 millivolt 1 mV
0.01 volts 10 millivolts 10 mV
0.1 volts 100 millivolts 100 mV
1 volt 1,000 millivolts 1V
Ampere basics
We measure electrical flow in amperes, or amps. The ampere is an international
unit, often referred to as an“amp.”A milliamp is 1/1,000 of an ampere.
Number of amperes Usually expressed as Abbreviated as
0.001 amps 1 milliamp 1 mA
0.01 amps 10 milliamps 10 mA
0.1 amps 100 milliamps 100 mA
1 amp 1,000 milliamps 1A
Figure 1-35. When you attach both wires to
the fuse, the little S-shaped element inside
will melt almost instantly.
Figure 1-36. A 3-amp fuse, before its
element was melted by a single 1.5-volt
battery.
Figure 1-37. The same fuse after being
melted by electric current.

Chapter 112
Fundamentals
Direct and alternating current
The flow of current that you get from a battery is known as direct current, or DC.
Like the flow of water from a faucet, it is a steady stream, in one direction.
The flow of current that you get from the“hot”wire in a power outlet in your
home is very different. It changes from positive to negative 50 times each
second (in Great Britain and some other nations, 60 times per second). This is
known as alternating current, or AC, which is more like the pulsatile flow you get
from a power washer.
Alternating current is essential for some purposes, such as cranking up voltage
so that electricity can be distributed over long distances. AC is also useful in
motors and domestic appliances. The parts of an American power outlet are
shown in Figure 1-39. A few other nations, such as Japan, also use American-
style outlets.
For most of this book I’m going to be talking about DC, for two reasons: first,
most simple electronic circuits are powered with DC, and second, the way it
behaves is much easier to understand.
I won’t bother to mention repeatedly that I’m dealing with DC. Just assume that
everything is DC unless otherwise noted.
B
A
C
Figure 1-39. This style of power outlet is found in North America, South America,
Japan, and some other nations. European outlets look different, but the principle
remains the same. Socket A is the “live” side of the outlet, supplying voltage that
alternates between positive and negative, relative to socket B, which is called the
“neutral” side. If an appliance develops a fault such as an internal loose wire, it
should protect you by sinking the voltage through socket C, the ground.
Background
Inventor of the battery
Alessandro Volta (Figure 1-38) was
born in Italy in 1745, long before
science was broken up into spe-
cialties. After studying chemistry
(he discovered methane in 1776),
he became a professor of physics
and became interested in the so-
called galvanic response, whereby
a frog’s leg will twitch in response
to a jolt of static electricity.
Using a wine glass full of salt
water, Volta demonstrated that the
chemical reaction between two
electrodes, one made of copper,
the other of zinc, will generate a
steady electric current. In 1800, he
refined his apparatus by stacking
plates of copper and zinc, sepa-
rated by cardboard soaked in salt
and water. This“voltaic pile”was
the first electric battery.
Figure 1-38. Alessandro Volta discov-
ered that chemical reactions can
create electricity.

The first AA battery that you shorted out is probably damaged beyond repair.
You should dispose of it. Putting batteries in the trash is not a great idea, be-
cause they contain heavy metals that should be kept out of the ecosystem.
Your state or town may include batteries in a local recycling scheme. (Califor-
nia requires that almost all batteries be recycled.) You’ll have to check your
local regulations for details.
The blown fuse is of no further use, and can be thrown away.
The second battery, which was protected by the fuse, should still be OK. The
battery holder also can be reused later.
Now it’s time to make electricity do something that’s at least slightly useful. For
this purpose, you’ll use components known as resistors, and a light-emitting di-
ode, or LED.
You will need:
• 1.5-volt AA batteries. Quantity: 4.
• Four-battery holder. Quantity: 1.
• Resistors: 470Ω, 1K, and either 2K or 2.2K (the 2.2K value happens to be
more common than 2K, but either will do in this experiment). Quantity: 1
of each resistor.
• An LED, any type. Quantity: 1.
• Alligator clips. Quantity: 3.
Setup
It’s time to get acquainted with the most fundamental component we’ll be us-
ing in electronic circuits: the humble resistor. As its name implies, it resists the
flow of electricity. As you might expect, the value is measured in ohms.
If you bought a bargain-basement assortment package of resistors, you
may find nothing that tells you their values. That’s OK; we can find out easily
enough. In fact, even if they are clearly labeled, I want you to check their values
yourself. You can do it in two ways:
• Use your multimeter. This is excellent practice in learning to interpret the
numbers that it displays.
• Learn the color codes that are printed on most resistors. See the following
section,“Fundamentals: Decoding resistors,”for instructions.
After you check them, it’s a good idea to sort them into labeled compartments
in a little plastic parts box. Personally, I like the boxes sold at the Michaels chain
of crafts stores, but you can find them from many sources.
Background
Father of
electromagnetism
Born in 1775 in France, André-
Marie Ampère (Figure 1-40) was
a mathematical prodigy who
became a science teacher, despite
being largely self-educated in his
father’s library. His best-known
work was to derive a theory
of electromagnetism in 1820,
describing the way that an electric
current generates a magnetic field.
He also built the first instrument
to measure the flow of electricity
(now known as a galvanometer),
and discovered the element
fluorine.
Figure 1-40. Andre-Marie Ampere
found that an electric current run-
ning through a wire creates a mag-
netic field around it. He used this
principle to make the first reliable
measurements of what came to be
known as amperage.

Chapter 114
Fundamentals
Decoding resistors
Some resistors have their value clearly stated on them in microscopic print that
you can read with a magnifying glass. Most, however, are color-coded with
stripes. The code works like this: first, ignore the color of the body of the resis-
tor. Second, look for a silver or gold stripe. If you find it, turn the resistor so that
the stripe is on the righthand side. Silver means that the value of the resistor
is accurate within 10%, while gold means that the value is accurate within 5%.
If you don’t find a silver or gold stripe, turn the resistor so that the stripes are
clustered at the left end. You should now find yourself looking at three colored
stripes on the left. Some resistors have more stripes, but we’ll deal with those in
a moment. See Figures 1-41 and 1-42.
Figure 1-41. Some modern resistors have
their values printed on them, although
you may need a magnifier to read them.
This 15K resistor is less than half an
inch long.
Figure 1-42. From top to bottom, these
resistor values are 56,000 ohms (56K),
5,600 ohms (5.6K), and 560 ohms. The
size tells you how much power the resis-
tor can handle; it has nothing to do with
the resistance. The smaller components
are rated at 1/4 watt; the larger one in
the center can handle 1 watt of power.
Starting from the left, the first and
second stripes are coded according to
this table:
Black 0
Brown 1
Red 2
Orange 3
Yellow 4
Green 5
Blue 6
Violet 7
Gray 8
White 9
The third stripe has a different mean-
ing: It tells you how many zeros to
add, like this:
Black - No zeros
Brown 0 1 zero
Red 00 2 zeros
Orange 000 3 zeros
Yellow 0000 4 zeros
Green 00000 5 zeros
Blue 000000 6 zeros
Violet 0000000 7 zeros
Gray 00000000 8 zeros
White 000000000 9 zeros

Fundamentals
Decoding resistors (continued)
Note that the color-coding is consistent, so that green, for instance, means
either a value of 5 (for the first two stripes) or 5 zeros (for the third stripe). Also,
the sequence of colors is the same as their sequence in a rainbow.
So, a resistor colored brown-red-green would have a value of 1-2 and five zeros,
making 1,200,000 ohms, or 1.2MΩ. A resistor colored orange-orange-orange
would have a value of 3-3 and three zeros, making 33,000 ohms, or 33KΩ. A
resistor colored brown-black-red would have a value of 1-0 and two additional
zeros, or 1KΩ. Figure 1-43 shows some other examples.
Wider gap between bands
Gold or silver band
Figure 1-43. To read the value of a resistor, first turn it so that the silver or gold stripe
is on the right, or the other stripes are clustered on the left. From top to bottom:
The first resistor has a value of 1-2 and five zeros, or 1,200,000, which is 1.2MΩ. The
second is 5-6 and one zero, or 560Ω. The third is 4-7 and two zeros, or 4,700, which is
4.7KΩ. The last is 6-5-1 and two zeros, or 65,100Ω, which is 65.1KΩ.
If you run across a resistor with four stripes instead of three, the first three
stripes are digits and the fourth stripe is the number of zeros. The third numeric
stripe allows the resistor to be calibrated to a finer tolerance.
Confusing? Absolutely. That’s why it’s easier to use your meter to check the values.
Just be aware that the meter reading may be slightly different from the claimed
value of the resistor. This can happen because your meter isn’t absolutely accu-
rate, or because the resistor is not absolutely accurate, or both. As long as you’re
within 5% of the claimed value, it doesn’t matter for our purposes.

Chapter 116
Lighting an LED
Now take a look at one of your LEDs. An old-fashioned lightbulb wastes a lot
of power by converting it into heat. LEDs are much smarter: they convert al-
most all their power into light, and they last almost indefinitely—as long as
you treat them right!
An LED is quite fussy about the amount of power it gets, and the way it gets it.
Always follow these rules:
• The longer wire protruding from the LED must receive a more positive volt-
age than the shorter wire.
• The voltage difference between the long wire and the short wire must not
exceed the limit stated by the manufacturer.
• The current passing through the LED must not exceed the limit stated by
the manufacturer.
What happens if you break these rules? Well, we’re going to find out!
Make sure you are using fresh batteries. You can check by setting your multi-
meter to measure volts DC, and touching the probes to the terminals of each
battery. You should find that each of them generates a pressure of at least
1.5 volts. If they read slightly higher than this, it’s normal. A battery starts out
above its rated voltage, and delivers progressively less as you use it. Batteries
also lose some voltage while they are sitting on the shelf doing nothing.
Load your battery holder (taking care that the batteries are the right way
around, with the negative ends pressing against the springs in the carrier).
Use your meter to check the voltage on the wires coming out of the battery
carrier. You should have at least 6 volts.
Now select a 2KΩ resistor. Remember, “2KΩ” means “2,000 ohms.” If it has col-
ored stripes, they should be red-black-red, meaning 2-0 and two more zeros.
Because 2.2K resistors are more common than 2K resistors, you can substitute
one of them if necessary. It will be colored red-red-red.
Wire it into the circuit as shown in Figures 1-44 and 1-45, making the connec-
tions with alligator clips. You should see the LED glow very dimly.

Now swap out your 2K resistor and substitute a 1K resistor, which will have
brown-black-red stripes, meaning 1-0 and two more zeros. The LED should
glow more brightly.
Swap out the 1K resistor and substitute a 470Ω resistor, which will have yel-
low-violet-brown stripes, meaning 4-7 and one more zero. The LED should be
brighter still.
This may seem very elementary, but it makes an important point. The resistor
blocks a percentage of the voltage in the circuit. Think of it as being like a kink
or constriction in a flexible hose. A higher-value resistor blocks more voltage,
leaving less for the LED.
CLIP
CLIP
CLIP
LED
On your battery
pack, this wire
may be either
blue or black.
Longer wire Shorter wire
6v Battery Pack
Figure 1-45. Here’s how it actually looks, using a large LED. If you start with the highest
value resistor, the LED will glow very dimly as you complete the circuit. The resistor drops
most of the voltage, leaving the LED with insufficient current to make it shine brightly.
We’ll use the batteries and the LED in the next experiment. The resistors can
be reused in the future.
Figure 1-44. The setup for Experiment 3,
showing resistors of 470Ω, 1KΩ, and 2KΩ.
Apply alligator clips where shown, to make
a secure contact, and try each of the resis-
tors one at a time at the same point in the
circuit, while watching the LED.

Chapter 118
Potentiometers come in various shapes and sizes, but they all do the same
thing: they allow you to vary voltage and current by varying resistance. This
experiment will enable you to learn more about voltage, amperage, and the
relationship between them.You’ll also learn how to read a manufacturer’s data
sheet.
You will need the same batteries, battery carrier, alligator clips, and LED from
the last experiment, plus:
• Potentiometer, 2KΩ linear. Quantity: 2. (See Figure 1-46.) Full-sized poten-
tiometers that look like this are becoming less common, as miniature ver-
sions are taking their place. I’d like you to use a large one, though, because
it’s so much easier to work with.
• One extra LED.
• Multimeter.
Look Inside Your Potentiometer
The first thing I want you to do is find out how a potentiometer works. This
means you’ll have to open it, which is why your shopping list required you to
buy two of them, in case you can’t put the first one back together again.
Most potentiometers are held together with little metal tabs. You should be
able to grab hold of the tabs with your wire cutters or pliers, and bend them
up and outward. If you do this, the potentiometer should open up as shown in
Figures 1-47 and 1-48.
Figure 1-46 Figure 1-47 Figure 1-48. To open the potentiometer,
first pry up the four little metal tabs
around the edge (you can see one sticking
out at the left and another one sticking out
at the right in Figure 1-47). Inside is a coil
of wire around a flat plastic band, and a
pair of springy contacts (the wiper), which
conduct electricity to or from any point in
the coil when you turn the shaft.
Depending whether you have a really cheap potentiometer or a slightly more
high-class version, you may find a circular track of conductive plastic or a loop
of coiled wire. Either way, the principle is the same. The wire or the plastic

possesses some resistance (a total of 2K in this instance), and as you turn the
shaft of the potentiometer, a wiper rubs against the resistance, giving you a
shortcut to any point from the center terminal.
You can try to put it back together, but if it doesn’t work, use your backup
potentiometer instead.
To test your potentiometer, set your meter to measure resistance (ohms) and
touch the probes while turning the potentiometer shaft to and fro, as shown
in Figure 1-49.
Dimming Your LED
Begin with the potentiometer turned all the way counterclockwise, otherwise
you’ll burn out the LED before we even get started. (A very, very small num-
ber of potentiometers increase and decrease resistance in the opposite way
to which I’m describing here, but as long as your potentiometer looks like the
one in Figure 1-48 after you open it up, my description should be accurate.)
Now connect everything as shown in Figures 1-50 and 1-51, taking care that
you don’t allow the metal parts of any of the alligator clips to touch each other.
Now turn up the potentiometer very slowly. You’ll notice the LED glowing
brighter, and brighter, and brighter—until, oops, it goes dark. You see how
easy it is to destroy modern electronics? Throw away that LED. It will never
glow again. Substitute a new LED, and we’ll be more careful this time.
CLIP
CLIP
CLIP
LED
Begin with the potentiometer turned
all the way counter-clockwise,
and then rotate the shaft in
the direction of the arrow.
On your battery
pack, this wire
may be either
blue or black.
Longer wire Shorter wire
6v Battery Pack
Figure 1-50. The setup for Experiment 4. Rotating the shaft of the 2K potentiometer varies
its resistance from 0 to 2,000Ω. This resistance protects the LED from the full 6 volts of
the battery.
Ohms
Figure 1-49. Measure the resistance be-
tween these two terminals of the potenti-
ometer while you turn its shaft to and fro.
Figure 1-51. The LED in this photo is dark
because I turned the potentiometer up
just a little bit too far.

Chapter 120
While the batteries are connected to the circuit, set your meter to measure volts
DC as shown in Figures 1-52 through 1-54. Now touch the probes either side of
the LED. Try to hold the probes in place while you turn the potentiometer up
a little, and down a little. You should see the voltage pressure around the LED
changing accordingly. We call this the potential difference between the two
wires of the LED.
If you were using a miniature old-fashioned lightbulb instead of an LED, you’d
see the potential difference varying much more, because a lightbulb behaves
like a“pure”resistor, whereas an LED self-adjusts to some extent, modifying its
resistance as the voltage pressure changes.
Now touch the probes to the two terminals of the potentiometer that we’re
using, so that you can measure the potential difference between them. The
potentiometer and the LED share the total available voltage, so when the po-
tential difference (the voltage drop) around the potentiometer goes up, the
potential difference around the LED goes down, and vice versa. See Figures
1-55 through 1-57. A few things to keep in mind:
• If you add the voltage drops across the devices in the circuit, the total is
the same as the voltage supplied by the batteries.
• You measure voltage relatively, between two points in a circuit.
• Apply your meter like a stethoscope, without disturbing or breaking the
connections in the circuit.
6v Battery Pack
Use your meter to
measure the voltage
between these two
points.
Then compare
the voltage between
these two points.
Figure 1-55. How to measure voltage in a simple circuit.
Figure 1-52
Figure 1-53
Figure 1-54. Each meter has a different
way to measure volts DC. The manually
adjusted meter (top) requires you to move
a slider switch to “DC” and then choose
the highest voltage you want to measure:
In this case, the selected voltage is 20
(because 2 would be too low). Using the
autoranging RadioShack meter, you set it
to “V” and the meter will figure out which
range to use.

6v Battery Pack
Volts
Figure 1-56. The meter shows how much voltage the LED takes.
6v Battery Pack
Volts
Figure 1-57. The meter shows how much voltage the potentiometer
takes.
Checking the Flow
Now I want you to make a different measurement. I want you to measure the
flow, or current, in the circuit, using your meter set to mA (milliamps). Remem-
ber, to measure current:
• You can only measure current when it passes through the meter.
• You have to insert your meter into the circuit.
• Too much current will blow the fuse inside your meter.
Make sure you set your meter to measure mA, not volts, before you try this.
Some meters require you to move one of your leads to a different socket on
the meter, to measure mA. See Figures 1-58 through 1-61.

Chapter 122
Figure 1-58. Any meter will blow its internal
fuse if you try to make it measure too high
an amperage. In our circuit, this is not a
risk as long as you keep the potentiometer
in the middle of its range. Choose “mA” for
milliamps and remember that the meter
displays numbers that mean thousandths
of an amp.
Figure 1-59 Figure 1-60
Figure 1-61. A manual meter such as the one here may require you to shift the red lead to
a different socket, to measure milliamps. Most modern meters don’t require this until you
are measuring higher currents.
Insert your meter into the circuit, as shown in Figure 1-62. Don’t turn the po-
tentiometer more than halfway up. The resistance in the potentiometer will
protect your meter, as well as the LED. If the meter gets too much current,
you’ll find yourself replacing its internal fuse.
As you adjust the potentiometer up and down a little, you should find that the
varying resistance in the circuit changes the flow of current—the amperage.
This is why the LED burned out in the previous experiment: too much current
made it hot, and the heat melts it inside, just like the fuse in the previous ex-
periment. A higher resistance limits the flow of current, or amperage.
Now insert the meter in another part of the circuit, as shown in Figure 1-63. As
you turn the potentiometer up and down, you should get exactly the same re-
sults as with the configuration in Figure 1-64. This is because the current is the
same at all points in a similar circuit. It has to be, because the flow of electrons
has no place else to go.

It’s time now to nail this down with some numbers. Here’s one last thing to
try. Set aside the LED and substitute a 1KΩ resistor, as shown in Figure 1-64.
The total resistance in the circuit is now 1KΩ plus whatever the resistance the
potentiometer provides, depending how you set it. (The meter also has some
resistance, but it’s so low, we can ignore it.)
Amps
6v Battery Pack
Figure 1-62. To measure amps, as illustrated here and in Figure
1-63, the current has to pass through the meter. When you
increase the resistance, you restrict the current flow, and the
lower flow makes the LED glow less brightly.
6v Battery Pack
Amps
Figure 1-63

Chapter 124
6v Battery Pack
Amps
Figure 1-64. If you substitute a resistor instead of the LED, you can confirm that the cur-
rent flowing through the circuit varies with the total resistance in the circuit, if the voltage
stays the same.
Turn the potentiometer all the way counterclockwise, and you have a total of
3K resistance in the circuit. Your meter should show about 2 mA flowing. Now
turn the potentiometer halfway, and you have about 2K total resistance. You
should see about 3 mA flowing. Turn the potentiometer all the way clockwise,
so there’s a total of 1K, and you should see 6 mA flowing. You may notice that
if we multiply the resistance by the amperage, we get 6 each time—which just
happens to be the voltage being applied to the circuit. See the following table.
Total resistance Current Voltage
(KΩ) (mA) (Volts)
3 2 6
2 3 6
1 6 6

In fact, we could say:
voltage = kilohms × milliamps
But wait a minute: 1K is 1,000 ohms, and 1mA is 1/1,000 of an amp. Therefore,
our formula should really look like this:
voltage = (ohms × 1,000) × (amps/1,000)
The two factors of 1,000 cancel out, so we get this:
volts = ohms × amps
This is known as Ohm’s Law. See the section, “Fundamentals: Ohm’s Law,” on
the following page.
Fundamentals
Series and parallel
Before we go any further, you should know how resistance
in a circuit increases when you put resistors in series or in
parallel. Figures 1-65 through 1-67 illustrate this. Remember:
• Resistors in series are oriented so that one follows the
other.
• Resistors in parallel are oriented side by side.
When you put two equal-valued resistors in series, you
double the total resistance, because electricity has to pass
through two barriers in succession.
When you put two equal-valued resistors in parallel, you
divide the total resistance by two, because you’re giving the
electricity two paths which it can take, instead of one.
In reality we don’t normally need to put resistors in parallel,
but we often put other types of components in parallel.
Lightbulbs in your house, for instance, are all wired that way.
So, it’s useful to understand that resistance in a circuit goes
down if you keep adding components in parallel.
1,000 ohms
circuit resistance
6mA current
6 volts
6 volts
1,000 ohms
Figure 1-65. One resistor takes the entire voltage, and according
to Ohm’s Law, it draws v/R = 6/1,000 = 0.006 amps = 6mA of
current.
3 volts
3 volts
2,000 ohms
circuit resistance
3mA current
6 volts
1,000 ohms
1,000 ohms
Figure 1-66. When two resistors are in series, the electricity has
to pass through one to reach the other, and therefore each
of them takes half the voltage. Total resistance is now 2,000
ohms, and according to Ohm’s Law, the circuit draws v/R =
6/2,000 = 0.003 amps = 3mA of current.
500 ohms
circuit resistance
12mA current
6 volts
6 volts
1,000 ohms
1,000 ohms
6 volts
Figure 1-67. When two resistors are in parallel, each is exposed
to the full voltage, so each of them takes 6 volts. The electric-
ity can now flow through both at once, so the total resistance
of the circuit is half as much as before. According to Ohm’s
Law, the circuit draws v/R = 6/500 = 0.012 amps = 12mA of
current.

Chapter 126
Using Ohm’s Law
Ohm’s Law is extremely useful. For example, it helps us to figure out whether a
component can be used safely in a circuit. Instead of stressing the component
until we burn it out, we can predict whether it will work.
For instance, the first time you turned the potentiometer, you didn’t really
know how far you could go until the LED burned out. Wouldn’t it be useful
to know precisely what resistance to put in series with an LED, to protect it
adequately while providing as much light as possible?
How to Read a Data Sheet
Like most information, the answer to this question is available online.
Here’s how you find a manufacturer’s data sheet (Figure 1-68). First, find the
component that you’re interested in from a mail-order source. Next, Google
the part number and manufacturer’s name. Usually the data sheet will pop up
as the first hit. A source such as Mouser.com makes it even easier by giving you
a direct link to manufacturers’data sheets for many products.
VISHAY
TLHG / R / Y540.
Vishay Semiconductors
e2 Pb
Pb-free
19223
e2 Pb
Pb-free
19223
e2 Pb
Pb-free
19223
e2 Pb
Pb-free
19223
e2 Pb
Pb-free
19223
e2 Pb
Pb-free
19223
e2 Pb
Pb-free
19223
e2 Pb
Pb-free
19223
High Efficiency LED in 5 mm Tinted Diffused Package
Description
The TLH.54.. series was developed for standard
applications like general indicating and lighting pur-
poses.
It is housed in a 5 mm tinted diffused plastic package.
The wide viewing angle of these devices provides a
high on-off contrast.
Several selection types with different luminous inten-
sities are offered. All LEDs are categorized in lumi-
nous intensity groups. The green and yellow LEDs
are categorized additionally in wavelength groups.
That allows users to assemble LEDs with uniform
appearance.
Features
• Choice of three bright colors
Standard T-1� package
Small mechanical tolerances
Suitable for DC and high peak current
Wide viewing angle
Luminous intensity categorized
Yellow and green color categorized
TLH.54.. with stand-offs
Lead-free device
Applications
Status lights
OFF / ON indicator
Background illumination
Readout lights
Maintenance lights
Legend light
Figure 1-68. The beginning of a typical data sheet, which includes all relevant specifica-
tions for the product, freely available online.
Fundamentals
Ohm’s Law
For reasons I’ll explain in a mo-
ment, amps are normally abbrevi-
ated with the letter I. V stands for
volts and R stands for resistance
in ohms (because the omega
symbol, Ω, is not easily generated
from most keyboards). Using these
symbols, you can write Ohm’s Law
in three different ways:
V = I × R
I = V/R
R = V/I
Remember, V is a difference in
voltage between two points in a
simple circuit, R is the resistance
in ohms between the same two
points, and I is the current in
amps flowing through the circuit
between the two points.
Letter I is used because origi-
nally current was measured by its
inductance, meaning the ability to
induce magnetic effects. It would
be much less confusing to use A
for amps, but unfortunately it’s too
late for that to happen.

Background
How much voltage does a wire consume?
Normally, we can ignore the resistance in electric wires, such as the little leads
of wire that stick out of resistors, because it’s trivial. However, if you try to force
large amounts of current through long lengths of thin wire, the resistance of
the wire can become important.
How important? Once again, we can use Ohm’s Law to find out.
Suppose that a very long piece of wire has a resistance of 0.2Ω. And we want to
run 15 amps through it. How much voltage will the wire steal from the circuit,
because of its resistance?
Once again, you begin by writing down what you know:
R = 0.2
I = 15
We want to know V, the potential difference, for the wire, so we use the version
of Ohm’s Law that places V on the left side:
V = I × R
Now plug in the values:
V = 15 × 0.2 = 3 volts
Three volts is not a big deal if you have a high-voltage power supply, but if you
are using a 12-volt car battery, this length of wire will take one-quarter of the
available voltage.
Now you know why the wiring in automobiles is relatively thick—to reduce its
resistance well below 0.2Ω. See Figure 1-69.
Some kind of
electrical
device
Figure 1-69. When a 12-volt car battery runs some kind of electrical device through
a long piece of thin wire, the resistance of the wire steals some of the voltage and
dissipates it as heat.

Chapter 128
Here’s an example. Suppose I want a red LED, such as theVishay partTLHR5400,
which has become such a common item that I can buy them individually for 9
cents apiece. I click the link to the data sheet maintained by the manufacturer,
Vishay Semiconductor. Almost immediately I have a PDF page on my screen.
This data sheet is for TLHR, TLHG, and TLHY types of LED, which are red, green,
and yellow respectively, as suggested by the R, G, and Y in the product codes.
I scroll down and look at the “Optical and Electrical Characteristics” section.
It tells me that under conditions of drawing a current of 20 mA, the LED will
enjoy a“Typ,”meaning, typical,“forward voltage”of 2 volts.The“Max,”meaning
maximum, is 3 volts.
Let’s look at one other data sheet, as not all of them are written the same way.
I’ll choose a different LED, the Kingbright part WP7113SGC. Click on the link
to the manufacturer’s site, and I find on the second page of the data sheet a
typical forward voltage of 2.2, maximum 2.5, and a maximum forward current
of 25 mA. I also find some additional information: a maximum reverse voltage
of 5 and maximum reverse current of 10 uA (that’s microamps, which are 1,000
times smaller than milliamps). This tells us that you should avoid applying ex-
cessive voltage to the LED the wrong way around. If you exceed the reverse
voltage, you risk burning out the LED. Always observe polarity!
Kingbright also warns us how much heat the LED can stand: 260° C (500° F) for
a few seconds. This is useful information, as we’ll be putting aside our alligator
clips and using hot molten solder to connect electrical parts in the near future.
Because we have already destroyed a battery, a fuse, and an LED in just four ex-
periments, maybe you won’t be surprised when I tell you that we will destroy
at least a couple more components as we test their limits with a soldering iron.
Anyway, now we know what an LED wants, we can figure out how to supply
it. If you have any difficulties dealing with decimals, check the Fundamentals
section“Decimals,”on the next page, before continuing.
How Big a Resistor Does an LED Need?
Suppose that we’re use the Vishay LED. Remember its requirements from the
data sheet? Maximum of 3 volts, and a safe current of 20mA.
I’m going to limit it to 2.5 volts, to be on the safe side. We have 6 volts of bat-
tery power. Subtract 2.5 from 6 and we get 3.5. So we need a resistor that will
take 3.5 volts from the circuit, leaving 2.5 for the LED.
The current flow is the same at all places in a simple circuit. If we want a maxi-
mum of 20mA to flow through the LED, the same amount of current will be
flowing through the resistor.
Now we can write down what we know about the resistor in the circuit. Note
that we have to convert all units to volts, amps, and ohms, so that 20mA should
be written as 0.02 amps:
V = 3.5 (the potential drop across the resistor)
I = 0.02 (the current flowing through the resistor)
Background
The origins of wattage
James Watt (Figure 1-70) is known
as the inventor of the steam
engine. Born in 1736 in Scotland,
he set up a small workshop in the
University of Glasgow, where he
struggled to perfect an efficient
design for using steam to move a
piston in a cylinder. Financial prob-
lems and the primitive state of
the art of metal working delayed
practical applications until 1776.
Despite difficulties in obtaining
patents (which could only be
granted by an act of parliament
in those times), Watt and his
business partner eventually made
a lot of money from his innova-
tions. Although he predated the
pioneers in electricity, in 1889 (70
years after his death), his name
was assigned to the basic unit of
electric power that can be defined
by multiplying amperes by volts.
See the Fundamentals section,
“Watt Basics,”on page 31.
Figure 1-70. James Watt’s develop-
ment of steam power enabled the
industrial revolution. After his death,
he was honored by having his name
applied to the basic unit of power in
electricity.

We want to know R, the resistance. So, we use the version of Ohm’s Law that
puts R on the left side:
R= V/I
Now plug in the values:
R = 3.5/0.02
Run this through your pocket calculator if you find decimals confusing. The
answer is:
R = 175Ω
It so happens that 175Ω isn’t a standard value. You may have to settle for 180
or 220Ω, but that’s close enough.
Evidently the 470Ω resistor that you used in Experiment 3 was a very conserva-
tive choice. I suggested it because I said originally that you could use any LED
at all. I figured that no matter which one you picked, it should be safe with
470Ω to protect it.
The dead LED can be thrown away. Everything else is reusable.
Fundamentals
Decimals
Legendary British politician Sir Winston Churchill is famous for complain-
ing about“those damned dots.”He was referring to decimal points. Because
Churchill was Chancellor of the Exchequer at the time, and thus in charge of all
government expenditures, his difficulty with decimals was a bit of a problem.
Still, he muddled through in time-honored British fashion, and so can you.
You can also use a pocket calculator—or follow two basic rules.
Doing multiplication: combine the zeros
Suppose you need to multiply 0.04 by 0.005:
1. Count the total number of zeros following both of the decimal points. In
this case, three zeros.
2. Multiply the numbers which follow the zeros. In this case, 4 × 5 = 20.
3. Write down the result as 0 followed by a decimal point, followed by the
number of zeros, followed by the multiplication result. Like this: 0.00020,
which is the same as 0.0002.
Doing division: cancel the zeros
Suppose you need to divide 0.006 by 0.0002:
1. Shift the decimal points to the right, in both the numbers, by the same
number of steps, until both the numbers are greater than 1. In this case,
shift the point four steps in each number, so you get 60 divided by 2.
2. Do the division. The result in this case is 30.

Chapter 130
Theory
Doing the math on your tongue
I’m going to go back to the question I asked in the previous
experiment: why didn’t your tongue get hot?
Now that you know Ohm’s Law, you can figure out the
answer in numbers. Let’s suppose the battery delivered
its rated 9 volts, and your tongue had a resistance of 50K,
which is 50,000 ohms. Write down what you know:
V = 9
R = 50,000
We want to know the current, I, so we use the version of
Ohm’s Law that puts this on the left:
I = V/R
Plug in the numbers:
I = 9/50,000 = 0.00018 amps
Move the decimal point three places to convert to milliamps:
I = 0.18 mA
That’s a tiny current that will not produce much heat at 9
volts.
What about when you shorted out the battery? How much
current made the wires get hot? Well, suppose the wires had
a resistance of 0.1 ohms (probably it’s less, but I’ll start with
0.1 as a guess). Write down what we know:
V = 1.5
R = 0.1
Once again we’re trying to find I, the current, so we use:
I = V/R
Plug in the numbers:
I = 1.5/0.1 = 15 amps
That’s 100,000 times the current that may have passed
through your tongue, which would have generated much
more heat, even though the voltage was lower.
Could that tiny little battery really pump out 15 amps?
Remember that the battery got hot, as well as the wire. This
tells us that the electrons may have met some resistance
inside the battery, as well as in the wire. (Otherwise, where
else did the heat come from?) Normally we can forget about
the internal resistance of a battery, because it’s so low. But at
high currents, it becomes a factor.
I was reluctant to short-circuit the battery through a meter,
to try to measure the current. My meter will fry if the current
is greater than 10A. However I did try putting other fuses
into the circuit, to see whether they would blow. When I
tried a 10A fuse, it did not melt. Therefore, for the brand of
battery I used, I’m fairly sure that the current in the short
circuit was under 10A, but I know it was over 3A, because
the 3A fuse blew right away.
The internal resistance of the 1.5-volt battery prevented
the current in the short circuit from getting too high. This
is why I cautioned against using a larger battery (especially
a car battery). Larger batteries have a much lower internal
resistance, allowing dangerously high currents which gener-
ate explosive amounts of heat. A car battery is designed to
deliver literally hundreds of amps when it turns a starter
motor. That’s quite enough current to melt wires and cause
nasty burns. In fact, you can weld metal using a car battery.
Lithium batteries also have low internal resistance, making
them very dangerous when they’re shorted out. High cur-
rent can be just as dangerous as high voltage.

Fundamentals
Watt basics
So far I haven’t mentioned a unit that everyone is familiar with: watts.
A watt is a unit of work. Engineers have their own definition of work—they say
that work is done when a person, an animal, or a machine pushes something to
overcome mechanical resistance. Examples would be a steam engine pulling a
train on a level track (overcoming friction and air resistance) or a person walk-
ing upstairs (overcoming the force of gravity).
When electrons push their way through a circuit, they are overcoming a kind
of resistance, and so they are doing work, which can be measured in watts. The
definition is easy:
watts = volts × amps
Or, using the symbols customarily assigned, these three formulas all mean the
same thing:
W = V × I
V = W/I
I = W/V
Watts can be preceded with an“m,”for“milli,”just like volts:
Number of watts Usually expressed as Abbreviated as
0.001 watts 1 milliwatt 1mW
0.01 watts 10 milliwatts 10 mW
0.1 watts 100 milliwatts 100 mW
1 watt 1,000 milliwatts 1W
Because power stations, solar installations, and wind farms deal with much
larger numbers, you may also see references to kilowatts (using letter K) and
megawatts (with a capital M, not to be confused with the lowercase m used to
define milliwatts):
Number of watts Usually expressed as Abbreviated as
1,000 watts 1 kilowatt 1 KW
1,000,000 watts 1 megawatt 1 MW
Lightbulbs are calibrated in watts. So are stereo systems. The watt is named
after James Watt, inventor of the steam engine. Incidentally, watts can be con-
verted to horsepower, and vice versa.
Theory
Power assessments
I mentioned earlier than resistors
are commonly rated as being
capable of dealing with 1/4 watt,
1/2 watt, 1 watt, and so on. I sug-
gested that you should buy resis-
tors of 1/4 watt or higher. How did
I know this?
Go back to the LED circuit. Re-
member we wanted the resistor to
drop the voltage by 3.5 volts, at a
current of 20 mA. How many watts
of power would this impose on
the resistor?
Write down what you know:
V = 3.5 (the voltage drop
imposed by the resistor)
I = 20mA = 0.02 amps
(the current flowing through
the resistor)
We want to know W, so we use this
version of the formula:
W = V × I
Plug in the values:
W = 3.5 × 0.02 = 0.07 watts
(the power being dissipated
by the resistor)
Because 1/4 watt is 0.25 watts, ob-
viously a 1/4 watt resistor will have
about four times the necessary
capacity. In fact you could have
used a 1/8 watt resistor, but in
future experiments we may need
resistors that can handle 1/4 watt,
and there’s no penalty for using a
resistor that is rated for more watts
than will actually pass through it.

Chapter 132
Long ago, before web surfing, file sharing, or cell phones, kids were so horribly
deprived that they tried to amuse themselves with kitchen-table experiments
such as making a primitive battery by pushing a nail and a penny into a lemon.
Hard to believe, perhaps, but true!
This is seriously old-school—but I want you to try it anyway, because anyone
who wants to get a feel for electricity should see how easy it is to extract it
from everyday objects around us. Plus, if you use enough lemons, you just
might generate enough voltage to power an LED.
The basic components of a battery are two metal electrodes immersed in an
electrolyte. I won’t define these terms here (they’re explained in the following
section “Theory: The nature of electricity”). Right now all you need to know is
that lemon juice will be your electrolyte, and copper and zinc will be your elec-
trodes. A penny provides the necessary copper, as long as it is fairly new and
shiny. Pennies aren’t solid copper anymore, but they are still copper-plated,
which is good enough.
To find some metallic zinc, you will have to make a trip to a hardware store,
where you should ask for roofing nails. The nails are zinc-plated to prevent
them from rusting. Small metal brackets or mending plates also are usually
zinc-plated. They should have a slightly dull, silvery look. If they have a mirror-
bright finish, they’re more likely to be nickel-plated.
Cut a lemon in half, set your multimeter so that it can measure up to 2 volts DC,
and hold one probe against a penny while you hold the other probe against
a roofing nail (or other zinc-plated object). Now force the penny and the nail
into the exposed juicy interior of the lemon, as close to each other as possible,
but not actually touching. You should find that your meter detects between
0.8 volts and 1 volt.
You can experiment with different items and liquids to see which works best.
Immersing your nail and penny in lemon juice that you have squeezed into a
shot glass or egg cup may enhance the efficiency of your battery, although
you’ll have a harder time holding everything in place. Grapefruit juice and vin-
egar will work as substitutes for lemon juice.
To drive a typical LED, you need more than 1 volt. How to generate the extra
electrical pressure? By putting batteries in series, of course. In other words,
more lemons! (Or more shot glasses or egg cups.) You’ll also need lengths of
wire to connect multiple electrodes, and this may entail skipping ahead to
Chapter 2, where I describe how to strip insulation from hookup wire. Figures
1-71 and 1-72 show the configuration.
If you set things up carefully, making sure than none of the electrodes are
touching, you may be able to illuminate your LED with two or three lemon-
juice batteries in series. (Some LEDs are more sensitive to very low currents
than others. Later in the book I’ll be talking about very-low-current LEDs. If you
want your lemon-juice battery to have the best chance of working, you can
search online for low-current LEDs and buy a couple.)
Figure 1-71. A three-lemon battery. Don’t
be too disappointed if the LED fails to
light up. The lemons have a high electri-
cal resistance, so they can’t deliver much
current, especially through the relatively
small surface area of the nails and the
pennies. However, the lemon battery does
generate voltage that you can measure
with your meter.
Figure 1-72. Bottled lemon juice seems to
work just as well as fresh lemon juice. I cut
the bottoms off three paper cups, inserted
a galvanized bracket into each, and used
heavyweight stranded copper wire to
make the positive electrodes

Theory
The nature of electricity
To understand electricity, you have to start with some basic
information about atoms. Each atom consists of a nucleus
at the center, containing protons, which have a positive
charge. The nucleus is surrounded by electrons, which carry
a negative charge.
Breaking up the nucleus of an atom requires a lot of energy,
and can also liberate a lot of energy—as happens in a
nuclear explosion. But persuading a couple of electrons to
leave an atom (or join an atom) takes very little energy. For
instance, when zinc reacts chemically with an acid, it can
liberate electrons. This is what happens at the zinc electrode
of the chemical battery in Experiment 5.
The reaction soon stops, as electrons accumulate on the
zinc electrode. They feel a mutual force of repulsion, yet
they have nowhere to go. You can imagine them like a
crowd of hostile people, each one wanting the others to
leave, and refusing to allow new ones to join them, as
shown in Figure 1-73.
Figure 1-73. Electrons on an electrode have a bad attitude
known as mutual repulsion.
Now consider what happens when a wire connects the zinc
electrode, which has a surplus of electronics, to another
electrode, made from a different material, that has a short-
age of electrons. The electrons can pass through the wire
very easily by jumping from one atom to the next, so they
escape from the zinc electrode and run through the wire,
propelled by their great desire to get away from each other.
See Figure 1-74. This mutual force of propulsion is what cre-
ates an electrical current.
Now that the population of electrons on the zinc electrode
has been reduced, the zinc-acid reaction can continue,
replacing the missing electrodes with new ones—which
promptly imitate their predecessors and try to get away
from each other by running away down the wire. The
process continues until the zinc-acid reaction grinds to a
halt, usually because it creates a layer of a compound such
as zinc oxide, which won’t react with acid and prevents the
acid from reacting with the zinc underneath. (This is why
your zinc electrode may have looked sooty when you pulled
it out of the acidic electrolyte.)
Figure 1-74. As soon as we open up a pathway from a zinc
electrode crowded with electrons to a copper electrode, which
contains “holes” for the electrons, their mutual repulsion
makes them try to escape from each other to their new home
as quickly as possible.
This description applies to a“primary battery,”meaning one
that is ready to generate electricity as soon as a connection
between its terminals allows electrons to transfer from one
electrode to the other. The amount of current that a primary
battery can generate is determined by the speed at which
chemical reactions inside the battery can liberate electrons.
When the raw metal in the electrodes has all been used
up in chemical reactions, the battery can’t generate any
more electricity and is dead. It cannot easily be recharged,
because the chemical reactions are not easily reversible, and
the electrodes may have oxidized.
In a rechargeable battery, also known as a secondary bat-
tery, a smarter choice of electrodes and electrolyte does
allow the chemical reactions to be reversed.

Chapter 134
How much current is being generated in your lemon battery? Set your meter
to measure milliamps, and connect it between the nail and the penny. I mea-
sured about 2mA, but got 10mA when I used some #10 stranded copper wire
instead of a penny and a large mending plate instead of a roofing nail, im-
mersed in a cup of grapefruit juice. When a larger surface area of metal makes
better contact with the electrolyte, you get a greater flow of current. (Don’t
ever connect your meter to measure amps directly between the terminals of
a real battery. The current will be too high, and can blow the fuse inside your
meter.)
What’s the internal resistance of your lemon? Put aside the copper and zinc
electrodes and insert your nickel-plated meter probes into the juice. I got a
reading of around 30K when both probes were in the same segment of the
lemon, but 40K or higher if the probes were in different segments. Is the resis-
tance lower when you test liquid in a cup?
Here are a couple more questions that you may wish to investigate. For how
long will your lemon battery generate electricity? And why do you think your
zinc-plated electrode becomes discolored after it has been used for a while?
Electricity is generated in a battery by an exchange of ions, or free electrons, be-
tween metals. If you want to know more about this, check the section“Theory:
The nature of electricity”on the previous page.
The hardware that you immersed in lemons or lemon juice may be discolored,
but it is reusable. Whether you eat the lemons is up to you.

Background
Positive and negative
If electricity is a flow of electrons, which have a negative
charge, why do people talk as if electricity flows from the
positive terminal to the negative terminal of a battery?
The answer lies in a fundamental embarrassment in the
history of research into electricity. For various reasons, when
Benjamin Franklin was trying to understand the nature of
electric current by studying phenomena such as lightning
during thunderstorms, he believed he observed a flow of
“electrical fluid”from positive to negative. He proposed this
concept in 1747.
In fact, Franklin had made an unfortunate error that
remained uncorrected until after physicist J. J. Thomson
announced his discovery of the electron in 1897, 150 years
later. Electricity actually flows from an area of greater nega-
tive charge, to some other location that is“less negative”—
that is,“more positive.”In other words, electricity is a flow
of negatively charged particles. In a battery, they originate
from the negative terminal and flow to the positive terminal.
You might think that when this fact was established, every-
one should have discarded Franklin’s idea of a flow from
positive to negative. But when an electron moves through a
wire, you can still think of an equal positive charge flowing
in the opposite direction. When the electron leaves home,
it takes a small negative charge with it; therefore, its home
becomes a bit more positive. When the electron arrives at
its destination, its negative charge makes the destination a
bit less positive. This is pretty much what would happen if
an imaginary positive particle traveled in the opposite direc-
tion. Moreover, all of the mathematics describing electrical
behavior are still valid if you apply them to the imaginary
flow of positive charges.
As a matter of tradition and convenience we still retain Ben
Franklin’s erroneous concept of flow from positive to nega-
tive, because it really makes no difference. In the symbols
that represent components such as diodes and transistors,
you will actually find arrows reminding you which way
these components should be placed—and the arrows all
point from positive to negative, even though that’s not the
way things really work at all! Ben Franklin would have been
surprised to learn that although most lightning strikes occur
when a negative charge in clouds discharges to neutralize
a positive charge on the ground, some forms of lightning
are actually a flow of electrons from the negatively charged
surface of the earth, up to a positive charge in the clouds.
That’s right: someone who is“struck by lightning”may be
hurt by emitting electrons rather than by receiving them, as
shown in Figure 1-75.
Figure 1-75. In some weather conditions, the flow of electrons
during a lightning strike can be from the ground, through your
feet, out of the top of your head, and up to the clouds. Benjamin
Franklin would have been surprised.

Chapter 136
Theory
Basic measurements
Electrical potential is measured by adding up the charges
on individual electrons. The basic unit is the coulomb, equal
to the total charge on about 6,250,000,000,000,000,000
electrons.
If you know how many electrons pass through a piece of
wire each second, this establishes the flow of electricity,
which can be expressed in amperes. In fact 1 ampere can be
defined as 1 coulomb per second. Thus:
1 ampere = 1 coulomb/second
= about 6.25 quintillion electrons/second
There’s no way to“see”the number of electrons running
through a conductor (Figure 1-76), but there are indirect
ways of getting at this information. For instance, when an
electron goes running through a wire, it creates a wave of
electromagnetic force around it. This force can be measured,
and we can calculate the amperage from that. The electric
meter installed at your home by the utility company func-
tions on this principle.
Figure 1-76. If you could look inside an electric wire with a suf-
ficiently powerful magnifying device, and the wire happened
to be carrying 1 ampere of electron flow at the time, you might
hope to see about 6.25 quintillion electrons speeding past
each second.
If electrons are just moving freely, they aren’t doing any
work. If you had a loop of wire of zero resistance, and you
kick-started a flow of electrons somehow, they could just
go buzzing around forever. (This is what happens inside a
superconductor—almost.)
Under everyday conditions, even a copper wire has some re-
sistance. The force that we need to push electrons through
it is known as“voltage,”and creates a flow that can create
heat, as you saw when you shorted out a battery. (If the wire
that you used had zero resistance, the electricity running
through it would not have created any heat.) We can use the
heat directly, as in an electric stove, or we can use the elec-
trical energy in other ways—to run a motor, for instance.
Either way, we are taking energy out of the electrons, to do
some work.
One volt can be defined as the amount of pressure that you
need to create a flow of 1 ampere, which does 1 watt of
work. As previously defined, 1 watt = 1 volt × 1 ampere, but
the definition actually originated the other way around:
1 volt = 1 watt/1 ampere
It’s more meaningful this way, because a watt can be de-
fined in nonelectrical terms. Just in case you’re interested,
we can work backward through the units of the metric
system like this:
1 watt = 1 joule/second
1 joule = a force of 1 newton acting through 1 meter
1 newton = the force required to accelerate 1 kilogram
by 1 meter per second, each second
On this basis, the electrical units can all be anchored with
observations of mass, time, and the charge on electrons.

Practically Speaking
For practical purposes, an intuitive understanding of electricity can be more
useful than the theory. Personally I like the water analogies that have been
used for decades in guides to electricity. Figure 1-77 shows a tall tank half full
of water, with a hole punched in it near the bottom. Think of the tank as being
like a battery. The height of the water is comparable to voltage. The volume of
flow through the hole, per second, is comparable to amperage. The smallness
of the hole is comparable to resistance. See Figure 1-79 on the next page.
Where’s the wattage in this picture? Suppose we place a little water wheel
where it is hit by the flow from the hole. We can attach some machinery to
the water wheel. Now the flow is doing some work. (Remember, wattage is a
measurement of work.)
Maybe this looks as if we’re getting something for nothing, extracting work
from the water wheel without putting any energy back into the system. But
remember, the water level in the tank is falling. As soon as I include some help-
ers hauling the waste water back up to the top of the tank (in Figure 1-78), you
see that we have to put work in to get work out.
Similarly, a battery may seem to be giving power out without taking anything
in, but the chemical reactions inside it are changing pure metals into metallic
compounds, and the power we get out of a battery is enabled by this change
of state. If it’s a rechargeable battery, we have to push power back into it to
reverse the chemical reactions.
Going back to the tank of water, suppose we can’t get enough power out of it
to turn the wheel. One answer could be to add more water. The height of the
water will create more force. This would be the same as putting two batteries
end to end, positive to negative, in series, to double the voltage. See Figure
1-80. As long as the resistance in the circuit remains the same, greater voltage
will create more amperage, because amperage = voltage/resistance.
What if we want to run two wheels instead of one? We can punch a second
hole in the tank, and the force (voltage) will be the same at each of them. How-
ever, the water level in the tank will drop twice as fast. Really, we’d do better to
build a second tank, and here again the analogy with a battery is good. If you
wire two batteries side by side, in parallel, you get the same voltage, but for
twice as long. The two batteries may also be able to deliver more current than
if you just used one. See Figure 1-81.
Summing up:
• Two batteries in series deliver twice the voltage.
• Two batteries in parallel can deliver twice the current.
All right, that’s more than enough theory for now. In the next chapter, we’ll
continue with some experiments that will build on the foundations of knowl-
edge about electricity, to take us gradually toward gadgets that can be fun
and useful.
Figure 1-77. If you want to get work out of
a system…
Figure 1-78. . . . somehow or other you have
to put work back into it.

Chapter 138
Same
resistance
Higher voltage
Greater force
creates more flow,
because amperage =
voltage / resistance,
and the voltage has
gone up, while
the resistance
has remained
the same.
Higher
water level
Figure 1-79. Greater force generates more flow, as long as the resistance remains the
same.
1.5volts
3volts
Figure 1-80. When you place two equal batteries in
series, you double the voltage.
1.5volts
fortwiceaslong
Figure 1-81. Two equal batteries that are wired in parallel
will deliver the same voltage for twice as long as one.

2
39
Switching Basics and More
The concept of switching is fundamental in electronics, and I’m not just talking
about power switches. By “switching,” I mean using one flow of electricity to
switch, or control, another. This is such an important principle that no digital
device can exist without it.
Today, switching is mostly done with semiconductors. Before I deal with them,
I’ll back up and illustrate the concept by introducing you to relays, which are
easier to understand, because you can see what’s going on inside them. And
before I get to relays, I’ll deal with everyday on/off switches, which may seem
very simple—but we have to nail down the basics.
Also in this chapter, I’ll deal with capacitance, because capacitance and resis-
tance are fundamental to electronic circuits. By the end of the chapter, you
should have a basic grounding in electronics and be able to build the noise-
making section of a simple intrusion alarm. This will be your first circuit that
does something genuinely useful!
As in the previous shopping list, you should visit the various online suppliers
for availability and pricing of components and devices. Manufacturers seldom
sell small numbers of parts directly. Check the appendix for a complete list of
URLs for all the companies mentioned here.
Devices
• Power supply/universal AC adapter, 3 to 12 volts at 1A (1,000 mA). See Fig-
ure 2-1. Part number 273-029 from RadioShack, part PH-62092 by Philips,
or similar.
• Breadboard suitable for integrated circuits. Quantity: 1. See Figures 2-2
and 2-3. Part 276-002 from RadioShack, model 383-X1000 made by PSP,
part 923252-I by 3M, or similar. A breadboard that has screw terminals
mounted beside it will be a little easier to use but more expensive than
one that does not have terminals.
Figure 2-1. This AC adapter delivers DC
from 3 to 12 volts, and is ideal for electron-
ics projects.
In this chapter
Experiment 6: Very Simple Switching
Experiment 7: Relay-Driven LEDs
Experiment 8: A Relay Oscillator
Experiment 9: Time and Capacitors
Experiment 10: Transistor Switching
Experiment 11: A Modular Project

Chapter 240
Figure 2-2. This “breadboard” for quickly
constructing electronic circuits has a metal
base, and screw terminals for attaching
wires from a power supply.
Figure 2-3. A breadboard without screw
terminals is almost as convenient, and is
cheaper.
Tools
Wire strippers
Ideal model 45-121 wire strippers for 16- to 26-gauge wire, or similar. See
Figure 2-4. (The“gauge”of the wire tells you how thick it is. A higher gauge
means a thinner wire. In this book, we will mainly be using thin wire of
20- to 24-gauge.)
You may also consider the Kronus Automatic Wire Strippers, part 64-
2981 from RadioShack, or GB Automatic Wire Strippers, part SE-92 from
Amazon.com. See Figure 2-5.
The Kronus and GB wire strippers are functionally identical. The advan-
tage of their design is that it enables you to strip insulation from a wire
with one hand. But they do not work well on really thin wire.
Figure 2-4. To use these wire strippers,
insert a piece of insulated wire in the
appropriate-sized hole between the jaws,
grip the handles, and pull a section of
insulation away. See page 45.
Figure 2-5. These automatic wire strippers
enable one-handed operation, but are not
suitable for very small wire diameters. See
page 44.

Switching Basics and More 41
Supplies
Hookup wire
Solid-conductor, 22-gauge, minimum 25 feet of each color. See Figure 2-6.
Part 278-1222 from RadioShack, catalog item 9948T17 from McMaster-
Carr, or check eBay for deals.
It’s easy to buy the wrong kind of wire.You need solid-core wire, which has
a single conductor inside the plastic insulation, not stranded, which has
multiple, thinner conductors. See Figures 2-7 and 2-8. You’re going to be
pushing wires into little holes in a “breadboard,” and stranded wire won’t
let you do this. You will also have problems if you buy wire thicker than
22-gauge. Remember: the lower the gauge number, the thicker the wire.
For a little extra money, you can buy an assortment of precut sections of
wire, with ends stripped and ready for use.Try catalog item JW-140 (jump-
er wire assortment) from All Electronics or search eBay for “breadboard
wire.”See Figure 2-9.
Patch cords
Patch cords are not strictly necessary but very convenient. You don’t want
audio or video patch cords, which have a plug on each end; you want
wires with alligator clips on each end, also sometimes referred to as “test
leads.”Try catalog item 461-1176-ND from Digi-Key or catalog item MTL-
10 from All Electronics. See Figure 2-10.
Figure 2-7. Solid-conductor wire of 22 or 24
gauge is suitable for most of the experi-
ments in this chapter.
Figure 2-8. Stranded is more flexible, but
cannot be used easily with breadboards.
Figure 2-9. Precut wires with stripped ends
can save a lot of time and trouble—if you
don’t mind paying a little extra.
Figure 2-10. Patch cords, sometimes known
as test leads, consist of wires preattached
to alligator clips. This is another of those
little luxuries that reduces the hassle factor
in hobby electronics.
Figure 2-6. Using hookup wire with differ-
ent colors of plastic insulation will help you
to distinguish one wire from another in
your circuits.

Chapter 242
Components
Pushbutton
Momentary-on, SPST, sometimes referred to as OFF-(ON) or (ON)-OFF
type. Must be PCB- or PC-mount, meaning is extremely small with thin
spiky contacts on the bottom. Quantity: 1. See Figure 2-11.
Examples are part number AB11AP by NKK, part MPA103B04 by Alco-
switch, or part EP11SD1CBE by C&K. If you have a choice, buy the cheap-
est, as we’re going to switch very low current.
Switches
Toggle switch, single-pole, double-throw (SPDT), sometimes referred to
as ON-ON type. Quantity: 2. See Figure 2-12.
Model S302T-RO by NKK is ideal; it has screw terminals that will eliminate
the need for alligator clips. Other options are catalog item MTS-4PC from
All Electronics or part 275-603 from RadioShack.
We won’t be switching large currents or high voltages, so the exact type of
switch is unimportant. However, the terminals on larger-size switches are
spaced wider apart, which makes them easier to deal with.
Relays
DPDT, nonlatching, 12v DC. Quantity: 2.
It’s important to get the right kind of relay—one whose configuration
matches the pictures I’ll be using. Look for parts FTR-F1CA012V or FTR-
F1CD012V by Fujitsu, G2RL-24-DC12 by Omron, or OMI-SH-212D by Tyco.
Avoid substitutions.
Potentiometer
1 megohm linear potentiometer, Part number 271-211 from RadioShack,
part number 24N-1M-15R-R from Jameco, or similar.
Transistors
NPN transistor, general-purpose, such as 2N2222 by STMicroelectronics,
part PN2222 by Fairchild, or part 2N2222 from RadioShack. Quantity: 4.
See Figure 2-13.
2N6027 programmable unijunction transistor manufactured by On Semi-
conductor or Motorola. Quantity: 4.
Capacitors
Electrolytic capacitors, assorted. Must be rated for a minimum of 25 volts
and include at least one capacitor of 1,000 μF (microfarads). If you search
on eBay, make sure you find electrolytic capacitors. If they’re rated for
higher voltages, that’s OK, although they will be physically larger than you
need. See Figure 2-14.
Figure 2-11. The terminals protruding from
this tiny pushbutton are spaced 0.2 inches
apart, making it ideal for the “breadboard”
that you’ll be using.
Figure 2-12. This relatively large toggle
switch made by NKK has screw terminals,
which will reduce the inconvenience of
attaching it to hookup wire.
Figure 2-13. Transistors are commonly sold
either in little metal cans or sealed into
little lumps of plastic. For our purposes,
the packaging makes no difference.
Figure 2-14. An assortment of electrolytic
capacitors.

Ceramic capacitors, assorted. Make sure you get at least one rated at
0.0047 μF (which can also be written as 47 nF). See Figure 2-15.
Resistors
If you bought only a minimal selection for experiments 1 through 5, now’s
the time to buy a larger assortment, so that you won’t be stuck needing
the one value that you don’t have. 1/4-watt minimum.
Loudspeaker
Any8Ω,1-inchminiatureloudspeakersuchaspart273-092fromRadioShack.
See Figure 2-16.
You will need:
• AA batteries. Quantity: 4.
• Battery carrier for 4 AA batteries. Quantity: 1.
• LED. Quantity: 1.
• Toggle switches, SPDT. Quantity: 2. See Figure 2-12.
• 220Ω or similar value resistor, 1/4-watt minimum. Quantity: 1.
• Wire or patch cords. See Figure 2-10, shown previously.
• Wire cutters and wire strippers if you don’t use patch cords. See Figure 2-4,
shown previously.
In Experiment 3, you illuminated an LED by attaching a battery, and switched
it off by removing the battery. For greater convenience our circuits should
have proper switches to control power, and while I’m dealing with the general
topic of switches, I’m going to explore all the varieties, using a circuit to sug-
gest some possibilities.
Assemble the parts as shown in Figures 2-17 and 2-18. The long lead on the
LED must connect with the resistor, because that is the more positive side of
the circuit.
You’ll notice that you have to include a couple lengths of wire. I suggest green
wire to remind you that these sections are not connected directly to positive
or to negative power. But you can use any color you like. You can also substi-
tute patch cords, if you have them. However, learning to strip insulation from
pieces of wire is a necessary skill, so let’s deal with that now.
Figure 2-15. Ceramic capacitors mostly
look like this, although many of them are
round or bead-shaped instead of square.
The packaging shape is unimportant to us.
Figure 2-16. This miniature loudspeaker,
just over 1 inch in diameter, is useful for
verifying audio output direct from transis-
tor circuits.

Chapter 244
6v Battery Pack
Short
LED lead
Long
LED lead
Figure 2-17. If the LED is on, flipping either of the switches will turn it off. If the LED is off,
either of the switches will turn it on. Use alligator clips to attach the wires to each other,
and to the switches if your switches don't have screw terminals. Be careful that the clips
don't touch each other.
Figure 2-18. Full-size toggle switches with
screw terminals make it easy to hook up
this simple circuit.
Tools
If automatic wire strippers (Figure 2-19) don’t grip skinny 22-gauge wire very
effectively, try the Ideal brand of wire strippers shown back in Figure 2-4, or
use plain and simple wire cutters as shown in Figure 2-20. When using wire
cutters, you hold the wire in one hand and apply the tool in your other hand,
squeezing the handles with moderate pressure—just enough to bite into the
insulation, but not so much that you chop the wire. Pull the wire down while
you pull the cutters up, and with a little practice you can rip the insulation off
to expose the end of the wire.
Macho hardware nerds may use their teeth to strip insulation from wires.When
I was younger, I used to do this. I have two slightly chipped teeth to prove it.
Really, it’s better to use the right tool for the job.
Figure 2-19. Using automatic wire strip-
pers, when you squeeze the handles the
jaw on the left clamps the wire, the sharp
grooves on the right bite into the insula-
tion. Squeeze harder and the jaws pull
away from each other, stripping the insula-
tion from the wire.

Figure 2-20. To remove insulation from
the end of a thin piece of wire, you can
also use wire cutters. This takes a little
practice.
Figure 2-21. Those who tend to misplace
tools, and feel too impatient to search for
them, may feel tempted to use their teeth
to strip insulation from wire. This may not
be such a good idea.
Connection Problems
Depending on the size of toggle switches that you are using, you may have
trouble fitting in all the alligator clips to hold the wires together. Miniature
toggle switches, which are more common than the full-sized ones these days,
can be especially troublesome (see Figure 2-22). Be patient: fairly soon we’ll
be using a breadboard, which will eliminate alligator clips almost completely.
Testing
Make sure that you connect the LED with its long wire toward the positive
source of power (the resistor, in this case). Now flip either of the toggle switch-
es. If the LED was on, it will go off, and if it was off, it will go on. Flip the other
toggle switch, and it will have the same effect. If the LED does not go on at all,
you’ve probably connected it the wrong way around. Another possibility is
that two of your alligator clips may have shorted out the battery.
Assuming your two switches do work as I described them, what’s going on
here? It’s time to nail down some basic facts.
Figure 2-22. Miniature toggle switches can
be used—ideally, with miniature alligator
clips—but watch out for short circuits.

Chapter 246
Fundamentals
All about switches
When you flip the type of toggle switch that you used in
Experiment 6, it connects the center terminal with one of
the outer terminals. Flip the switch back, and it connects the
center terminal with the other outer terminal, as shown in
Figure 2-23.
The center terminal is called the pole of the switch. Because
you can flip, or throw, this switch to make two possible con-
nections, it is called a double-throw switch. As mentioned ear-
lier, a single-pole, double-throw switch is abbreviated SPDT.
Some switches are on/off, meaning that if you throw them in
one direction they make a contact, but in the other direction,
they make no contact at all. Most of the light switches in your
house are like this. They are known as single-throw switches. A
single-pole, single-throw switch is abbreviated SPST.
Some switches have two entirely separate poles, so you
can make two separate connections simultaneously when
you flip the switch. These are called double-pole switches.
Check the photographs in Figures 2-24 through 2-26 of
old-fashioned“knife”switches (which are still used to teach
electronics to kids in school) and you’ll see the simplest
representation of single and double poles, and single and
double throws. Various toggle switches that have contacts
sealed inside them are shown in Figure 2-27.
Connected Connected
Figure 2-23. The center terminal is the pole of the switch.
When you flip the toggle, the pole changes its connection.
Figure 2-24. This primitive-looking single-
pole, double-throw switch does exactly
the same thing as the toggle switches in
Figure 2-25. A single-pole, single-throw
switch makes only one connection with
one pole. Its two states are simply open
and closed, on and off.
Figure 2-26. A double-pole, single-throw
switch makes two separate on/off
connections.

Fundamentals
All about switches (continued)
Figure 2-27. These are all toggle switches. Generally, the larger
the switch, the more current it can handle.
To make things more interesting, you can also buy switches
that have three or four poles. (Some rotary switches have
even more, but we won't be using them.) Also, some double-
throw switches have an additional“center off”position.
Putting all this together, I made a table of possible types of
switches (Figure 2-28). When you’re reading a parts catalog,
you can check this table to remind yourself what the ab-
breviations mean.
4PST
ON-OFF
Single
Pole
Double
Pole
3-Pole 4-Pole
Single
Throw
SPST
ON-OFF
DPST
ON-OFF
3PST
ON-OFF
4PDT
ON-ON
SPDT
ON-ON
DPDT
ON-ON
3PDT
ON-ON
4PDT
ON-OFF-ON
SPDT
ON-OFF-ON
DPDT
ON-OFF-ON
3PDT
ON-OFF-ON
Double
Throw
Double
Throw with
Center Off
Figure 2-28. This table summarizes all the various options for
toggle switches and pushbuttons.
Now, what about pushbuttons? When you press a door
bell, you’re making an electrical contact, so this is a type of
switch—and indeed the correct term for it is a momentary
switch, because it makes only a momentary contact. Any
spring-loaded switch or button that wants to jump back to
its original position is known as a momentary switch. We
indicate this by putting its momentary state in parentheses.
Here are some examples:
• OFF-(ON): Because the ON state is in parentheses, it’s
the momentary state. Therefore, this is a single-pole
switch that makes contact only when you push it, and
flips back to make no contact when you let it go. It is
also known as a“normally open”momentary switch,
abbreviated“NO.”
• ON-(OFF): The opposite kind of momentary single-pole
switch. It’s normally ON, but when you push it, you
break the connection. So, the OFF state is momentary.
It is known as a“normally closed”momentary switch,
abbreviated“NC.”
• (ON)-OFF-(ON): This switch has a center-off position.
When you push it either way, it makes a momentary
contact, and returns to the center when you let it go.
Other variations are possible, such as ON-OFF-(ON) or ON-
(ON). As long as you remember that parentheses indicate
the momentary state, you should be able to figure out what
these switches are.
Figure 2-29. This evil mad scientist is ready to apply power to
his experiment. For this purpose, he is using a single-pole,
double-throw knife switch, conveniently mounted on the wall of
his basement laboratory.

Chapter 248
Fundamentals
All about switches (continued)
Sparking
When you make and break an electrical connection, it tends
to create a spark. Sparking is bad for switch contacts. It eats
them until the switch doesn’t make a reliable connection
anymore. For this reason, you must use a switch that is ap-
propriate for the voltage and amperage that you are dealing
with. Electronic circuits generally are low-current, and
low-voltage, so you can use almost any switch, but if you are
switching a motor, it will tend to suck an initial surge of cur-
rent that is at least double the rating of the motor when it is
running constantly. You should probably use a 4-amp switch
to turn a 2-amp motor on and off.
Checking a switch
You can use your meter to check a switch. Doing this helps
you find out which contacts are connected when you turn
a switch one way or the other. It’s also useful if you have a
pushbutton and you can’t remember whether it’s the type
that is normally open (you press it to make a connection) or
normally closed (you press it to break the connection). Set
your meter to measure ohms, and touch the probes to the
switch terminals while you work the switch.
This is a hassle, though, because you have to wait while
the meter makes an accurate measurement. When you just
want to know whether there is a connection, your meter
has a“continuity tester”setting. It beeps if it finds a connec-
tion, and stays silent if it doesn’t. See Figures 2-30 through
2-32 for examples of meters set to test continuity. Figure
2-33 offers an example of a toggle switch being tested for
continuity.
Use the continuity-testing feature on your meter only on
circuits or components that have no power in them at the
time.
Figure 2-30 Figure 2-31 Figure 2-32. To check a circuit for conti-
nuity, turn the dial of your meter to the
symbol shown. Only use this feature
when there is no power in the compo-
nent or the circuit that you are testing.
Figure 2-33. When the switch connects two of its terminals, the meter shows zero
resistance between them and will beep if you have set it to verify continuity.

Background
Early switching systems
Switches seem to be such a fundamental feature of our world, and their concept
is so simple that it’s easy to forget that they went through a gradual process of
development and refinement. Primitive knife switches were quite adequate for
pioneers of electricity who simply wanted to connect and disconnect electric-
ity to some apparatus in a laboratory, but a more sophisticated approach was
needed when telephone systems began to proliferate. Typically, an operator at
a“switchboard”needed a way to connect any pair of 10,000 lines on the board.
How could it be done?
In 1878, Charles E. Scribner (Figure 2-34) developed the“jack-knife switch,”so
called because the part of it that the operator held looked like the handle of a
jackknife. Protruding from it was a plug, and when the plug was pushed into a
socket, it made contact inside the socket. The socket, in fact, was the switch.
Figure 2-34. Charles E. Scribner invented the “jack-knife switch” to satisfy the
switching needs of telephone systems in the late 1800s. Today’s audio jacks still
work on the same basis.*
Audio connectors on guitars and amplifiers still work on the same principle, and
when we speak of them as being“jacks,”the term dates back to Scribner’s inven-
tion. Switch contacts still exist inside a jack socket.
Today, of course, telephone switchboards have become as rare as telephone
operators. First they were replaced with relays—electrically operated switches,
which I’ll talk about later in this chapter. And then the relays were superceded
by transistors, which made everything happen without any moving parts. Be-
fore the end of this chapter, you’ll be switching current using transistors.
* The photo on which this drawing is based first appeared in The History of the Telephone by
Herbert Newton Casson in 1910 (Chicago: A. C. McClurg & Co.).

Chapter 250
Introducing Schematics
In Figure 2-35, I’ve redrawn the circuit from Experiment 6 in a simplified style
known as a “schematic.” From this point onward, I will be illustrating circuits
with schematics, because they make circuits easier to understand. You just
need to know a few symbols to interpret them.
Compare the schematic here with the drawing of the circuit in Figure 2-17.
They both show exactly the same thing: Components, and connections be-
tween them.The gray rectangles are the switches, the zigzag thing is the resis-
tor, and the symbol with two diagonal arrows is the LED.
The schematic LED symbol includes two arrows indicating that it emits light,
because there are some kinds of diodes, which we’ll get to later, that don’t.
The triangle inside the diode symbol always points from positive to negative.
Trace the path that electricity can take through the circuit and imagine the
switches turning one way or the other. You should see clearly now why either
switch will reverse the state of the LED from on to off or off to on.
This same circuit is used in houses where you have a switch at the bottom of
a flight of stairs, and another one at the top, both controlling the same light-
bulb.The wires in a house are much longer, and they snake around behind the
walls, but because their connections are still the same, they could be repre-
sented with the same basic schematic. See Figure 2-36.
A schematic doesn’t tell you exactly where to put the components. It just tells
you how to join them together. One problem: Different people use slightly
different schematic symbols to mean the same thing. Check the upcoming
section,“Fundamentals: Basic schematic symbols,”for the details.
220
Figure 2-35. This schematic shows the
same circuit as in Figure 2-17 and makes it
easier to see how the switches function.
Figure 2-36. The two-switch circuit shown
in Figures 2-17 and 2-35 is often found in
house wiring, especially where switches
are located at the top and bottom of a
flight of stairs. This sketch shows what
you might find inside the walls. Wires are
joined with “wire nuts” inside boxes that
are hidden from everyday view.
Larger versions of all schematics and
breadboard photos are available
online at this book's website: http://
oreilly.com/catalog/9780596153748.

Fundamentals
Basic schematic symbols
Schematic symbols are like words in a language: they have
mutated over the years into a confusing range of variations.
A simple on/off (single-pole, single-throw, or SPST) switch,
for instance, can be represented by any of the symbols
shown in Figure 2-37. They all mean exactly the same thing.
PoleContact
Figure 2-37. Variations on a theme: Just some of the differ-
ent styles used to depict a single-pole, single-throw switch in
schematic diagrams. The bottom version is the style used in
this book.
Figure 2-38 shows double-pole, double-throw switches. A
dotted line indicates a mechanical connection inside the
switch, so that when you flip it, you affect both the poles si-
multaneously. Remember, the poles are electrically isolated
from each other.
S1A
S1B
Figure 2-38. More variations: some different styles for depicting
a double-pole, double-throw switch. The style at bottom-right
is used in this book.
Once in a while, you may find a schematic in which switches
seem to be scattered around, but the way they are identi-
fied (such as S1A, S1B, S1C, and so on) tells you that this is
really all one switch with multiple poles.
In the schematics in this book, I’ll place a gray rectangle
behind each switch. This gray rectangle is not a standard
symbol; you won’t find it in other books. I’m just including it
to remind you that the parts inside are all contained in one
package.
A very important stylistic variation in schematics is the way
they show whether wires make a connection with each
other. Old schematics used to show a little semicircular
bump in a wire if it crossed another wire without making
a connection. Because modern circuit-drawing software
doesn’t create this style of schematic, it is no longer often
used. The modern style, which you are likely to find if you
browse through schematics online, can be summarized like
this:
• A dot joining two wires indicates an electrical
connection.
• No dot indicates no connection.

Chapter 252
Fundamentals
Basic schematic symbols (continued)
The problem is that this is not very intuitive, especially when
you’re just beginning to use schematics. When you see two
wires crossing, you can easily imagine that they are making
a connection, even though there’s no dot at the intersec-
tion. Therefore, in the interests of clarity, I’ve chosen to use
the old“semicircular bump”style of schematic in this book
(see Figure 2-39). It can be summarized like this:
• A dot joining two wires indicates an electrical
connection.
• A bump in a wire that crosses another wire indicates no
connection.
In this book, you won’t find wires crossing each other with-
out either a dot or a bump.
Figure 2-39. In wiring schematics, a dot always indicates an
electrical connection. However, the cross-shaped intersection
of wires at top-right is considered bad style because if the dot
is accidentally omitted or poorly printed, the intersection can
be mistaken for the type shown at bottom left, in which the
wires do not make a connection. All three of the configurations
in the bottom row indicate no connection, the first example
being the most common style, the center example being least
common, and the third being the most old-fashioned—although
for reasons of clarity, it is used in this book.
In a battery-powered circuit, you may find a battery symbol,
but more often you will find a little note indicating where posi-
tive voltage enters the system, while negative is indicated by a
“ground”symbol. In fact there may be ground symbols all over
the place.You have to remember that when you build a circuit,
all the wires leading to grounds must actually be connected
together, to the negative side of the voltage supply.
The idea of the ground symbol dates back to the time when
electronic gadgets were mounted on a metal chassis, which
was connected to the negative side of the power supply. The
ground symbol really meant“connect to the chassis.”Some
variants in the ground symbol are shown in Figure 2-40.
Figure 2-40. All of these symbols are used to mean the same
thing: connect the wire to “ground” or “chassis” or the negative
side of the power source. The far-right symbol is used in this
book.
In this book, we have color throughout, so I’ll show a red
positive and blue negative to clarify where the power is
connected, and I won’t use ground symbols. Once again,
my purpose is to minimize the risk of misunderstandings,
because I know how frustrating it is to build a circuit that
doesn’t work.
A big inconsistency in schematics is the way in which they
show resistors. The traditional zigzag symbol has been
abandoned in Europe. Instead they use a rectangle with a
number inside indicating the number of ohms. See Figure
2-41. The Europeans also changed the way in which decimal
points are represented: they omit them as much as possible,
because in badly printed schematics, the little dots tend to
get lost (or can be confused with dust and dirt). So, a 4.7KΩ
resistor will be listed as 4K7, and a 1.2MΩ resistor will be
1M2. I like this notation, so I’m going to be using it myself,
but I’ll be keeping the zigzag resistor symbol, which remains
widely used in the United States.
220
220
Figure 2-41. Two styles for depicting a 220Ω resistor. The upper
version is traditional, and still used in the United States. The
lower version is European.

Fundamentals
Potentiometers suffer from the same inconsistent style be-
tween the United States and Europe, but either way, you’ll
find an arrow showing where the wiper (usually, the center
terminal) touches the resistance. See Figure 2-42. And some-
times LEDs are shown inside circles, and sometimes not. I
prefer circles, myself. See Figure 2-46.
Figure 2-42. Potentiometer symbols: the left is traditional and
used in the United States, the right is European. In both cases
the arrow indicates the wiper (usually the center terminal).
Figure 2-43. Three ways of indicating a pushbutton switch.
Figure 2-44. The battery symbol is usually shown without + and
– symbols. I’ve added them for clarity.
Figure 2-45. Symbol for an incandescent lightbulb.
I’ll explore other symbol variants later in the book. Mean-
while, the most important things to remember are:
• The positions of components in a schematic are not
important.
• The styles of symbols used in a schematic are not
important.
• The connections between the components are ex-
tremely important.
Figure 2-46. Sometimes an LED is shown with a circle around it; sometimes not. In this book, I will include the circle. The arrows
indicate emitted light.

Chapter 254
Fundamentals
For example, the three LED circuits that I have included in
Figure 2-47 show components in different positions, using dif-
ferent symbols, but all three circuits function exactly the same
way, because their connections are the same. In fact, they
all depict the circuit that you built in Experiment 4, shown in
Figure 1-50.
Often the symbols in a schematic are placed so that the
circuit is most intuitively easy to understand, regardless of
how you may build it with actual components. Compare the
example in Figure 2-48, showing the two DPDT switches,
with the version shown back in Figure 2-35. The previous
one looked more like your bench-top version of it, but Fig-
ure 2-48 shows the flow of electricity more clearly.
2K
2K
Figure 2-47. These three schematics all depict the same basic
circuit. It’s the circuit that you built with the potentiometer in
Experiment 4.
In many schematics, the positive side of the power supply is
shown at the top of the diagram, and negative or ground at
the bottom. Many people also tend to draw a schematic with
an input (such as an audio input, in an amplifier circuit) at the
left side, and the output at the right. So,“positive voltage”
flows from top to bottom while a signal tends to pass from
left to right.
When I was planning this book, initially I drew the sche-
matics to conform with this top-to-bottom, left-to-right
convention, but as I started building and testing the circuits,
I changed my mind. We use a device known as a“bread-
board”to create circuits, and its internal connections require
us to lay out components very differently from a typical
schematic. When you’re starting to learn electronics, it’s very
confusing to try to rearrange components from a schematic
in the configuration that you need for a breadboard.
Therefore, throughout this book, you’ll find that I have
drawn the schematics to imitate the way you’ll wire them on
a breadboard. I believe the advantages of doing things this
way outweigh the disadvantages of being a little different
from the schematic styles that are used elsewhere.
220
Figure 2-48. This schematic is just another, clearer, simpler way
of showing the circuit that appeared in Figure 2-35.

You will need:
• AC adapter, wire cutters and strippers.
• DPDT relay. Quantity: 2.
• LEDs. Quantity: 2.
• Resistor, 680Ω approx. Quantity: 1.
• Pushbutton, SPST. Quantity: 1.
• Hookup wire, 22 gauge, or patch cords.
• Utility knife.
The next step in our exploration of switching is to use a remote-controlled
switch. By “remote-controlled,” I mean one to which you can send a signal to
turn it on or off. This kind of switch is known as a relay, because it relays an
instruction from one part of a circuit to another. Often a relay is controlled by
a low voltage or small current, and switches a larger voltage or higher current.
This setup can be cost-effective. When you start your car, for instance, a rela-
tively small, cheap switch sends a small signal down a relatively long, thin,
inexpensive piece of wire, to a relay that is near the starter motor. The relay
activates the motor through a shorter, thicker, more expensive piece of wire,
capable of carrying as much as 100 amps.
Similarly, when you raise the lid on an a top-loading washing machine during
its spin cycle, you close a lightweight switch that sends a small signal down a
thin wire to a relay. The relay handles the bigger task of switching off the large
motor spinning the drum full of wet clothes.
Before you begin this experiment, you need to upgrade your power supply.
We’re not going to use batteries anymore, because most relays require more
than 6 volts, and in any case you should have a power supply that can give you
a variety of voltages on demand. The simplest way to achieve this is by using
an AC adapter.
First you’ll set up the AC adapter. After you have it running, you’ll use it to
power the relay. Initially the relay will just switch between two LEDs, but then
you’ll modify the circuit to make the LEDs flash automatically. Finally you’ll re-
build the circuit on a breadboard, and say goodbye to alligator clips, for most
of the time at least.
Preparing Your AC Adapter
An AC adapter plugs into the wall and converts the high-voltage AC supply in
your home into a safe, low DC voltage for electronic devices. Any charger that
you use with your cell phone, or iPod, or laptop computer is a special-purpose
AC adapter that delivers only one voltage via a specific type of plug. I’ve asked
you to buy a general-purpose adapter that delivers many different voltages,
and we’re going to begin by getting rid of its plug.

Chapter 256
1. It’s important to make sure that your AC adapter is not plugged into the
wall!
2. Chop off the little plug at the end of its wire. See Figure 2-49.
3. Use a box cutter or utility knife or scissors to make a half-inch cut between
the two conductors, and then pull the conductors apart a couple of inches.
4. Use wire cutters to trim one of the conductors shorter than the other,
so that after you strip away a little of the insulation, the exposed copper
wires cannot easily touch each other. This is a precaution against short-
circuiting your AC adapter and burning it out.
5. Strip the two conductors using your wire strippers. Twist the copper
strands between finger and thumb so that there are no loose strands
sticking out. See Figure 2-50.
6. Make sure that the two wires are not touching each other, and plug your
AC adapter into a wall outlet. Set your meter to DC volts and apply the me-
ter probes to the wires from the adapter. If the voltage is preceded with
a minus sign, you have the probes the wrong way around. Reverse them
and the minus sign should go away. This tells you which wire is positive.
7. Mark the positive wire from the adapter. If the wire has white insulation,
you can mark it with a red marker. If it has black insulation, you can tag it
with a label.The positive wire will remain positive regardless of which way
up you plug the AC adapter into a wall outlet.
The Relay
The type of relay that I want you to use has little spiky legs on the bottom, in
a standardized layout. If you buy some other kind of relay, you will have to
figure out for yourself which pins are connected to the coil inside, which pins
go to the poles of the switch inside it, and which go to the normally closed
and normally open contacts. You can check the manufacturer’s data sheet for
this purpose, but I strongly suggest you use one of the relays mentioned in the
shopping list, so that you can follow the instructions here more easily.
I asked you to buy two relays so that you can use one for investigational pur-
poses—meaning that you can break it open and take a look inside. If you do
this very, very carefully, the relay should still be usable afterward. If not, well,
you still have a spare.
The easiest way to open the relay is with a box cutter or utility knife. Figures
2-52, 2-53, and 2-54 show the technique. Shave the edges of the plastic shell
containing the relay, beveling them until you see just a hair-thin opening.
Don’t go any farther; the parts inside are very, very close to its housing. Now
pop the top off. You can use needle-nosed pliers to nibble the rest of the shell
away. Read the following section,“Fundamentals: Inside a relay,”and then ap-
ply power to the relay to see how it works.
Figure 2-49. Preparing an AC adapter. First,
cut off the little low-voltage plug and throw
it away.
Figure 2-50. Second, strip the wires, mak-
ing one shorter than the other to reduce
the risk of them touching. Color one of the
adapter wires red with a marker, to identify
it as the positive one.

A
B
C
D
D
Figure 2-51. This is one way that the parts inside a relay can be arranged. The coil, A, gener-
ates a magnetic attraction pulling lever B downward. A plastic extension, C, pushes outward
against flexible metal strips and moves the poles of the relay, D, between the contacts.
Figure 2-52. To look inside a sealed relay,
shave the top edges of the plastic package
with a utility knife til you open a thin crack.
Figure 2-53. Insert the blade of your knife
to pry open the top, then repeat the proce-
dure for the sides.
Figure 2-54. If you are really, really careful,
the relay should still work after you open it.
Figure 2-55
Figure 2-56. Patience is essential when
carving the edges of a relay package in
order to open it. Faster methods such as a
tomahawk or a flamethrower will satisfy the
emotional needs of those with a short atten-
tion span, but results may be unpredictable.
Figure 2-57. Four assorted 12-volt relays,
shown with and without their packages.
The automotive relay (far left) is the sim-
plest and easiest to understand, because
it is designed without much concern for
the size of the package. Smaller relays are
more ingeniously designed, more complex,
and more difficult to figure out. Usually,
but not always, a smaller relay is designed
to switch less current than a larger one.

Chapter 258
Fundamentals
Inside a relay
A relay contains a coil of wire wrapped around an iron core.
When electricity runs through the coil, the iron core exerts
a magnetic force, which pulls a lever, which pushes or pulls
a springy strip of metal, closing two contacts. So as long as
electricity runs through the coil, the relay is“energized”and
its contacts remain closed.
When the power stops passing through the coil, the relay
lets go and the springy strip of metal snaps back into its
original position, opening the contacts. (The exception to
this rule is a latching relay, which requires a second pulse
through a separate coil to flip it back to its original posi-
tion; but we won’t be using latching relays until later in the
book.)
Relays are categorized like switches. Thus, you have SPST
relays, DPST, SPDT, and so on.
Compare the schematics in Figure 2-58 with the schematics
of switches in Figure 2-38. The main difference is that the
relay has a coil that activates the switch. The switch is shown
in its“relaxed”mode, when no power flows through the coil.
Figure 2-58. Various ways to show a relay in a schematic. Top
left: SPST. Top right and bottom left: SPDT. Bottom right:
DPDT. The styles at bottom-left and bottom-right will be used
in this book.
The contacts are shown as little triangles. When there are
two poles instead of one, the coil activates both switches
simultaneously.
Most relays are nonpolarized, meaning that you can run
electricity through the coil in either direction, and the relay
doesn’t care. You should check the data sheet to make sure,
though. Some relay coils work on AC voltage, but almost
all low-voltage relays use direct current—a steady flow of
electricity, such as you would get from a battery. We’ll be
using DC relays in this book.
Relays suffer from the same limitations as switches: their
contacts will be eroded by sparking if you try to switch too
much voltage. It’s not worth saving a few dollars by using
a relay that is rated for less current or voltage than your
application requires. The relay will fail you when you need it
most, and may be inconvenient to replace.
Because there are so many different types of relays, read the
specifications carefully before you buy one. Look for these
basics:
Coil voltage
The voltage that the relay is supposed to receive when
you energize it.
Set voltage
The minimum voltage that the relay needs to close its
switch. This will be a bit less than the ideal coil voltage.
Operating current
The power consumption of the coil, usually in milliamps,
when the relay is energized. Sometimes the power is
expressed in milliwatts.
Switching capacity
The maximum amount of current that you can switch
with contacts inside the relay. Usually this is for a“resis-
tive load,”meaning a passive device such as light bulb.
When you use a relay to switch on a motor, the motor
takes a big initial surge of current before it gets up to
speed. In this case, you should choose a relay rated
for double the current that the motor draws when it is
running.

Procedure
Turn the relay with its legs in the air and attach wires and LEDs as shown in
Figure 2-59, with a 680Ω resistor (a 1K resistor will be OK if you don’t have the
correct value). Also attach a pushbutton switch. (Your pushbutton switch may
look different from the one shown, but as long as it is a SPST pushbutton with
two contacts at the bottom, it will work the same way.) When you press the
pushbutton, the relay will make the first LED go out and the second LED light
up. When you release the pushbutton, the first LED lights up and the second
one goes out.
How It Works
Check the schematic in Figure 2-60 and compare it with Figure 2-59. Also see
Figure 2-62, which shows how the pins outside the relay make connections
inside the relay when its coil is energized, and when it is not energized.
This is a DPDT relay, but we are only using one pole and ignoring the other.
Why not buy a SPDT relay? Because I want the pins to be spaced the way they
are when you will upgrade this circuit by transferring it onto a breadboard,
which will happen very shortly.
On the schematic, I have shown the switch inside the relay in its relaxed
state. When the coil is energized, the switch flips upward, which seems
counterintuitive, but just happens to be the way that this particular relay is
made.
When you’re sure you understand how the circuit works, it’s time to move on
to the next step: making a small modification to get the relay to switch itself
on and off, as we’ll do in Experiment 8.
Figure 2-61. The layout of the
pins of the relay, superimposed
on a grid of 1/10-inch squares.
This is the type of relay that you
will need in Experiment 8.
Connected
Connected
Connected
Connected
Figure 2-62. How the relay connects the pins, when it is
not energized (left) and when it is energized (right).
12v DC from
AC adapter
Figure 2-59. As before, you can use patch
cords, if you have them, instead of some of
the wired connections shown here.
680
12v
DC
Figure 2-60. Same circuit, shown in sche-
matic form.

Chapter 260
You will need:
• AC adapter, breadboard, wire, wire cutters and strippers.
• DPDT relay. Quantity: 1.
• LEDs. Quantity: 2.
• Resistor, approximately 680Ω. Quantity: 1.
• Capacitor, electrolytic, 1,000 μF. Quantity: 1.
Look at the revised drawing in Figure 2-63 and the revised schematic in Figure
2-64 and compare them with the previous ones. Originally, there was a direct
connection from the pushbutton to the coil. In the new version, the power
gets to the coil by going, first, through the contacts of the relay.
680
12v
DC
Figure 2-64. The oscillator circuit shown in schematic form.
Now, when you press the button, the contacts in their relaxed state feed power
to the coil as well as to the lefthand LED. But as soon as the coil is energized, it
opens the contacts. This interrupts the power to the coil—so the relay relaxes,
and the contacts close again. They feed another pulse of power to the coil,
which opens the contacts again, and the cycle repeats endlessly.
Because we’re using a very small relay, it switches on and off extremely fast.
In fact, it oscillates perhaps 50 times per second (too fast for the LEDs to show
what’s really happening). Make sure your circuit looks like the one in the dia-
gram, and then press the pushbutton very briefly. You should hear the relay
make a buzzing sound. If you have impaired hearing, touch the relay lightly
with your finger, and you should feel the relay vibrating.
When you force a relay to oscillate like this, it’s liable to burn itself out or de-
stroy its contacts. That’s why I asked you to press the pushbutton briefly. To
make the circuit more practical, we need something to slow the relay down
and prevent it from self-destructing. That necessary item is a capacitor.
12v DC from
AC adapter
Figure 2-63. A small revision to the previ-
ous circuit causes the relay to start oscil-
lating when power is applied.

Adding Capacitance
Add a 1,000 μF electrolytic capacitor in parallel with the coil of the relay as
shown in the diagram in Figure 2-65 and the schematic in Figure 2-66. Check
Figure 2-14 if you’re not sure what a capacitor looks like.The 1,000 μF value will
be printed on the side of it, and I’ll explain what this means a little later.
Make sure the capacitor’s short wire is connected to the negative side of the
circuit; otherwise, it won’t work. In addition to the short wire, you should find
a minus sign on the body of the capacitor, which is there to remind you which
side is negative. Electrolytic capacitors are fussy about this.
When you press the button now, the relay should click slowly instead of buzz-
ing. What’s happening here?
A capacitor is like a tiny rechargeable battery. It’s so small that it charges in a
fraction of a second, before the relay has time to open its lower pair of con-
tacts. Then, when the contacts are open, the capacitor acts like a battery, pro-
viding power to the relay. It keeps the coil of the relay energized for about one
second. After the capacitor exhausts its power reserve, the relay relaxes and
the process repeats.
Fundamentals
Farad basics
The Farad is an international unit to measure capacitance. Modern circuits
usually require small capacitors. Consequently it is common to find capacitors
measured in microfarads (one-millionth of a farad) and even picofarads (one-
trillionth of a farad). Nanofarads are also used, more often in Europe than in the
United States. See the following conversion table.
0.001 nanofarad 1 picofarad 1 pF
0.01 nanofarad 10 picofarads 10 pF
0.1 nanofarad 100 picofarads 100 pF
1 nanofarad 1,000 picofarads 1,000 pF
0.001 microfarad 1 nanofarad 1 nF
0.01 microfarad 10 nanofarads 10 nF
0.1 microfarad 100 nanofarads 100 nF
1 microfarad 1,000 nanofarads 1,000 nF
0.000001 Farad 1 microfarad 1 mF
0.00001 Farad 10 microfarads 10 mF
0.0001 Farad 100 microfarads 100 mF
0.001 Farad 1,000 microfarads 1,000 mF
(You may encounter capacitances greater than 1,000 microfarads, but they are
uncommon.)
12v DC from
AC adapter
Figure 2-65. Adding a capacitor makes the
relay oscillate more slowly.
680
12v
DC
Figure 2-66. The capacitor appears at the
bottom of this schematic diagram.

Chapter 262
Fundamentals
Capacitor basics
DC current does not flow through a capacitor, but voltage can accumulate very
quickly inside it, and remains after the power supply is disconnected. Figures
2-67 and 2-68 may help to give you an idea of what happens inside a capacitor
when it is fully charged.
Figure 2-67. When DC voltage reaches a capacitor, no current flows, but the capaci-
tor charges itself like a little battery. The positive and negative charges are equal
and opposite.
Figure 2-68. You can imagine positive “charge particles” accumulating on one side
of the capacitor and attracting negative “charge particles” to the opposite side.
In most modern electrolytic capacitors, the plates have been reduced to two
strips of very thin, flexible, metallic film, often wrapped around each other,
separated by an equally thin insulator. Disc ceramic capacitors typically consist
of just a single disc of nonconductive material with metal painted on both sides
and leads soldered on.
The two most common varieties of capacitors are ceramic (capable of storing a
relatively small charge) and electrolytic (which can be much larger). Ceramics
are often disc-shaped and yellow in color; electrolytics are often shaped like
miniature tin cans and may be just about any color. Refer back to Figures 2-13
and 2-14 for some examples.
Getting Zapped by Capacitors
If a large capacitor is charged with
a high voltage, it can retain that
voltage for a long time. Because the
circuits in this book use low voltages,
you don’t have to be concerned
about that danger here, but if you
are reckless enough to open an old
TV set and start digging around
inside (which I do not recommend),
you may have a nasty surprise. An
undischarged capacitor can kill you
as easily as if you stick your finger
into an electrical outlet. Never touch
a large capacitor unless you really
know what you’re doing.

Fundamentals
Capacitor basics (continued)
Ceramic capacitors have no polarity, meaning that you can apply negative volt-
age to either side of them. Electrolytics do have polarity, and won’t work unless
you connect them the right way around.
The schematic symbol for a capacitor has two significant variants: with two
straight lines (symbolizing the plates inside a capacitor), or with one straight
line and one curved line, as shown in Figure 2-69. When you see a curved line,
that side of the capacitor should be more negative than the other. The schemat-
ic symbol may also include a + sign. Unfortunately, some people don’t bother
to draw a curved plate on a polarized capacitor, yet others draw a curved plate
even on a nonpolarized capacitor.
Figure 2-69. The generic schematic for a capacitor is on the left. The version on the
right indicates a polarized capacitor which requires its left plate to be “more posi-
tive” than its right plate. The plus sign is often omitted.
Figure 2-70. A tantalum capacitor was plugged into this breadboard, accidentally
connected the wrong way around to a power source capable of delivering a lot of
current. After a minute or so of this abuse, the capacitor rebelled by popping open
and scattering small flaming pieces, which burned their way into the plastic of the
breadboard. Lesson learned: observe polarity!
Capacitor Polarity
You must connect an electrolytic
capacitor so that its longer wire is
more positive than its shorter wire.
The shell of the capacitor is usually
marked with a negative sign near the
shorter wire.
Some capacitors may behave badly
if you don’t observe their polarity.
One time I connected a tantalum
capacitor to a circuit, using a power
supply able to deliver a lot of current,
and was staring at the circuit and
wondering why it wasn’t working
when the capacitor burst open and
scattered little flaming fragments of
itself in a 3-inch radius. I had forgot-
ten that tantalum capacitors can be
fussy about positive and negative
connections. Figure 2-70 shows the
aftermath.

Chapter 264
Background
Michael Faraday and capacitors
The earliest capacitors consisted of two metal plates with a very small gap
between them. The principle of the thing was simple:
• If one plate was connected to a positive source, the positive charges at-
tracted negative charges onto the other plate.
• If one plate was connected to a negative source, the negative charges
attracted positive charges onto the other plate.
Figures 2-67 and 2-68, shown previously, convey the basic idea.
The electrical storage capacity of a capacitor is known as its capacitance, and is
measured in farads, named after Michael Faraday (Figure 2-71), another of the
pantheon of electrical pioneers. He was an English chemist and physicist who
lived from 1791 to 1867.
Although Faraday was relatively uneducated and had little knowledge of math-
ematics, he had an opportunity to read a wide variety of books while working
for seven years as a bookbinder’s apprentice, and thus was able to educate
himself. Also, he lived at a time when relatively simple experiments could reveal
fundamental properties of electricity. Thus he made major discoveries including
electromagnetic induction, which led to the development of electric motors. He
also discovered that magnetism could affect rays of light.
His work earned him numerous honors, and his picture was printed on English
20-pound bank notes from 1991 through 2001.
Figure 2-71. Michael Faraday

Breadboarding the Circuit
I promised to free you in time from the frustrations of alligator clips, and that
time has come. Please turn your attention to the block of plastic with lots of
little holes in it that I asked you to buy. For reasons that I do not know, this is
called a breadboard. When you plug components into the holes, hidden metal
strips inside the breadboard connect the components for you, allowing you
to set up a circuit, test it, and modify it very easily. Afterward you can pull the
components off the breadboard and put them away for future experiments.
Without a doubt, breadboarding is the most convenient way to test some-
thing before you decide whether you want to keep it.
Almost all breadboards are designed to be compatible with integrated circuit
chips (which we will be using in Chapter 4 of this book). The chip straddles
an empty channel in the center of the breadboard with rows of little holes ei-
ther side—usually five holes per row. You insert other components into these
holes.
In addition, the breadboard should have columns of holes running down each
side. These are used to distribute positive and negative power.
Take a look at Figures 2-72 and 2-73, which show the upper part of a typical
breadboard seen from above, and the same breadboard seen as if with X-ray
vision, showing the metal strips that are embedded behind the holes.
Figure 2-72. A typical breadboard. You can plug components
into the holes to test a circuit very quickly.
Figure 2-73. This X-ray-vision view of the breadboard reveals
the copper strips that are embedded in it. The strips conduct
electricity from one component to another.

Chapter 266
Important note: some breadboards divide each vertical column of holes, on
the left and the right, into two separate upper and lower sections. Use your
meter’s continuity testing feature to find out if your breadboard conducts
power along its full length, and add jumper wires to link the upper and lower
half of the breadboard if necessary.
Figure 2-74 shows how you can use the breadboard to replicate your oscillat-
ing relay circuit. To make this work, you need to apply the positive and nega-
tive power from your AC adapter. Because the wire from your AC adapter is
almost certainly stranded, you’ll have difficulty pushing it into the little holes.
A way around this is to set up a couple of pieces of bare 22-gauge wire, and
use them as terminals to which you clip the wire from the adapter, as in Figure
2-75. (Yes, you still need just a couple of alligator clips for this purpose.) Alter-
natively, you can use a breadboard with power terminals built into it, which is
more convenient.
S1
R1
S2
D1
D2
C1
12v
DC
Figure 2-74. If you place the components on your breadboard in the posi-
tions shown, they will create the same circuit that you built from wire and
alligator clips in Experiment 8. Component values:
D1, D2: Light-emitting diodes
S1: DPDT relay
S2: SPST momentary switch
C1: Electrolytic capacitor, 1,000 µF
R1: Resistor, 680Ω minimum
Figure 2-75. If your breadboard doesn’t have screw
terminals, insert two short pieces of solid-core
wire with stripped ends and then attach the
stranded wires from the adapter using alligator
clips.

You’ll need some more 22-gauge wire, or some precut hookup wire, to supply
the power to your components, which are plugged into the breadboard as
shown in Figures 2-76 and 2-77. If you get all the connections right, the circuit
should function the same way as before.
The geometry of the metal connecting strips in the breadboard often forces
you to connect components in a roundabout way. The pushbutton, for in-
stance, supplies power to the pole of the relay but cannot be connected di-
rectly opposite, because there isn’t room for it.
Remember that the strips inside the breadboard that don’t have any wires or
components plugged into them are irrelevant; they don’t do anything.
I’ll include some suggested breadboard layouts for circuits as you continue
through this book, but eventually you’ll have to start figuring out breadboard
layouts for yourself, as this is an essential part of hobby electronics.
Figure 2-76. Two oversized LEDs, one resistor, and the necessary jumper wires have been
added to the breadboard.
Figure 2-77. Now the pushbutton, relay, and capacitor have been added to complete the
circuit shown in the diagram and the schematic. When the pushbutton is pressed, the
relay oscillates and the LEDs flash.

Chapter 268
You will need:
• AC adapter, breadboard, wire, wire cutters, and strippers.
• Multimeter.
• Resistors and electrolytic capacitors, assorted.
In Experiment 8, when you put a capacitor in parallel with the coil of the relay,
the capacitor charged almost instantly before discharging itself through the
relay coil. If you add a resistor in series with a capacitor, the capacitor will take
longer to charge. By making a capacitor take longer to charge, you can mea-
sure time, which is a very important concept.
Clean the components off your breadboard and use it to set up the very simple
circuit shown in Figure 2-78, where C1 is a 1,000 µF capacitor, R1 is a 100K resis-
tor, R2 is a 100Ω resistor, and S1 is the pushbutton that you used previously.
Set your meter to measure volts DC, place the probes around the capacitor,
and hold down the pushbutton. You should see the meter counting upward
as the voltage accumulates on the capacitor. (This is easier with a meter that
doesn’t have autoranging, because you won’t have to wait while the meter
figures out which range to apply.) Resistor R1 slows the charging time for the
capacitor.
Figure 2-78. Watch the voltage building up
on the capacitor while you hold down the
pushbutton. Substitute other values for
R1, discharge the capacitor by touching R2
across it, and then repeat your measure-
ment process.
S1: Momentary pushbutton, OFF (ON)
R1: 100K initially
R2: 100Ω
C1: 1,000 µF
S1
R1
C1
R2
Volts
12v
DC

Release the pushbutton, set aside your meter, and discharge the capacitor by
touching R2 across it for a second or two. Now substitute a 50K resistor for R1,
and repeat the measurement. The meter should count upward almost twice
as fast as before.
Voltage, Resistance, and Capacitance
Think of the resistor as a faucet, and the capacitor as a balloon that you are
trying to fill with water. When you screw down the faucet until only a trickle
comes through, the balloon will take longer to fill. But a slow flow of water will
still fill the balloon completely if you wait long enough, and (assuming the bal-
loon doesn’t burst) the process ends when the pressure inside the balloon is
equal to the water pressure in the pipe supplying the faucet. See Figure 2-79.
Similarly, in your circuit, if you wait long enough, eventually the voltage across
the capacitor should reach the same value as the voltage of the power supply.
In a 12-volt circuit, the capacitor should eventually acquire 12 volts (although
“eventually”may take longer than you think).
This may seem confusing, because earlier you learned that when you apply
voltage at one end of a resistor, you get less voltage coming out than you have
going in. Why should a resistor deliver the full voltage when it is paired with a
capacitor?
Forget the capacitor for a moment, and remember how you tested just two
1K resistors. In that situation, each resistor contained half the total resistance
of the circuit, so each resistor dropped half the voltage. If you held the nega-
tive probe of your meter against the negative side of your power supply and
touched the positive probe to the center point between the two resistors, you
would measure 6 volts. Figure 2-80 illustrates this.
Now, suppose you remove one of the 1K resistors and substitute a 9K resis-
tor. The total resistance in the circuit is now 10K, and therefore the 9K resistor
drops 90% of the 12 volts. That’s 10.8 volts. You should try this and check it
with your meter. (You are unlikely to find a 9K resistor, because this is not a
standard value. Substitute the nearest value you can find.)
Now suppose you remove the 9K resistor and substitute a 99K resistor. Its volt-
age drop will be 99% of the available voltage, or 11.88 volts.You can see where
this is heading: the larger the resistor, the larger its contribution to voltage
drop.
However, I noted previously that a capacitor blocks DC voltage completely. It
can accumulate an electrical charge, but no current passes through it.Therefore,
a capacitor behaves like a resistor that has infinite resistance to DC current.
(Actually the insulation inside the capacitor allows a little bit of“leakage,”but a
perfect capacitor would have infinite resistance.)
The value of any resistor that you put in series with the capacitor is trivial by
comparison. No matter how high the value of the resistor is, the capacitor
still provides much more resistance in the circuit. This means that the capaci-
tor steals almost the complete voltage drop in the circuit, and the voltage
Figure 2-79. When the faucet is closed
half-way, the balloon will take longer to fill,
but will still contain as much water and as
much pressure in the end.

Chapter 270
difference between one end of the resistor and the other will be zero (assum-
ing that we ignore little imperfections in the components). Figure 2-80 may
help to clarify this concept.
1K 1K
12v
DC
6
volts
6
volts
1K 9K
12v
DC
1.2
volts
10.8
volts
1K 99K
12v
DC
0.12
volts
11.88
volts
1K
infinite
resistance
12v
DC
0
volts
12
volts
Figure 2-80. When two resistances are in series, the larger one drops the voltage more
than the smaller one. If the larger resistance becomes infinite (as in the case of a capaci-
tor), the smaller one no longer has any measurable contribution to the voltage drop, and
the voltage is almost exactly the same at both ends.
You should try this using real resistors and capacitors—although if you do, you
will run into a little problem.When you use your meter in its“DC volts”mode, it
diverts a little of the current in the circuit—just a tiny taste—in the process of
measuring it. The meter steals such a small amount, it doesn’t affect the read-
ing significantly when you are checking voltage across a resistor. The internal
resistance of the meter is higher than the values of most resistors. However,
remember that the internal resistance of a capacitor is almost infinite. Now the
internal resistance of the meter becomes significant. Because you can never
have an ideal meter, any more than you can have an ideal capacitor or resistor,
your meter will always interfere with the circuit slightly, and you will get only
an approximate indication.
If you try to measure the voltage on a capacitor that has been charged but is
now not connected to anything else, you’ll see the number slowly falling, as
the capacitor discharges itself through the meter.

Theory
The time constant
You may be wondering if there’s a way to predict exactly
how much time it takes for various capacitors to charge,
when they are paired with various resistors. Is there a for-
mula to calculate this?
Of course, the answer is yes, but the way we measure it is a
bit tricky, because a capacitor doesn’t charge at a constant
rate. It accumulates the first volt very quickly, the second
volt not quite as quickly, the third volt even less quickly—
and so on. You can imagine the electrons accumulating on
the plate of a capacitor like people walking into an audito-
rium and looking for a place to sit. The fewer seats that are
left, the longer people take to find them.
The way we describe this is with something called a“time
constant.”The definition is very simple:
TC = R × C
where TC is the time constant, and a capacitor of C farads is
being charged through a resistor of R ohms.
Going back to the circuit you just tested, try using it again,
this time with a 1K resistor and the 1,000 µF capacitor. We
have to change those numbers to farads and ohms before
we can put them in the formula. Well, 1,000 µF is 0.001 far-
ads, and 1K is 1,000 ohms, so the formula looks like this:
TC = 1,000 × 0.001
In other words, TC = 1—a lesson that could not be much
easier to remember:
A 1K resistor in series with a 1,000 µF capacitor has a
time constant of 1.
Does this mean that the capacitor will be fully charged in 1
second? No, it’s not that simple. TC, the time constant, is the
time it takes for a capacitor to acquire 63% of the voltage
being supplied to it, if it starts with zero volts.
(Why 63%? The answer to that question is too complicated
for this book, and you’ll have to read about time constants
elsewhere if you want to know more. Be prepared for dif-
ferential equations.) Here’s a formal definition for future
reference:
TC, the time constant, is the time it takes for a capacitor
to acquire 63% of the difference between its current
charge and the voltage being applied to it. When TC=1,
the capacitor acquires 63% of its full charge in 1 sec-
ond. When TC=2, the capacitor acquires 63% of its full
charge in 2 seconds. And so on.
What happens if you continue to apply the voltage? History
repeats itself. The capacitor accumulates another 63% of the
remaining difference between its current charge, and the
voltage being applied to it.
Imagine someone eating a cake. In his first bite he’s raven-
ously hungry, and eats 63% of the cake in one second. In his
second bite, not wanting to seem too greedy, he takes just
another 63% of the cake that is left—and because he’s not
feeling so hungry anymore, he requires the same time to
eat it as he took to eat the first bite. In his third bite, he takes
63% of what still remains, and still takes the same amount
of time. And so on. He is behaving like a capacitor eating
electricity (Figure 2-81).
Figure 2-81. If our gourmet always eats just 63% of the cake still on the plate, he “charges up” his stomach in the same way that a
capacitor charges itself. No matter how long he keeps at it, his stomach is never completely filled.

Chapter 272
Theory
The time constant (continued)
The cake eater will always have a few crumbs to eat, be-
cause he never takes 100% of the remainder. Likewise, the
capacitor will never acquire a full charge. In a perfect world
of perfect components, this process would continue for an
infinite time.
In the real world, we say rather arbitrarily:
After 5 × TC the capacitor will be so nearly fully
charged, we won’t care about the difference.
In the table is a calculation (rounded to two decimal places)
showing the charge accumulating on a capacitor in a 12-
volt circuit where the time constant is 1 second.
Here’s how to understand the table. V1 is the current charge
on the capacitor. Subtract this from the supply voltage (12
volts) to find the difference. Call the result V2. Now take 63%
of V2, and add this to the current charge (V1) and call the
result V4. This is the new charge that the capacitor will have
after 1 second, so we copy it down to the next line in the
table, and it becomes the new value for V1.
Now we repeat the same process all over again. Figure 2-82
shows this in graphical form. Note that after 5 seconds,
the capacitor has acquired 11.92 volts, which is 99% of
the power supply voltage. This should be close enough to
satisfy anyone’s real-world requirements.
Time
in secs
V1:
Charge on capacitor
V2:
12 – V1
V3:
63% of V2
V4:
V1 + V3
0 0.00 12.00 7.56 7.56
1 7.56 4.44 2.80 10.36
2 10.36 1.64 1.03 11.39
3 11.39 0.61 0.38 11.77
4 11.77 0.23 0.15 11.92
5 11.92
If you try to verify these numbers by measuring the voltage
across the capacitor as it charges, remember that because
your meter steals a little current, there will be a small
discrepancy that will increase as time passes. For practical
purposes, the system works well enough.
TCTC TC TC
10
2
3
+63%
+63%
+63%
Figure 2-82. A capacitor starts with 0 volts. After 1 time con-
stant it adds 63% of the available voltage. After another time
constant, it adds another 63% of the remaining voltage differ-
ence, and so on.

You will need:
• AC adapter, breadboard, wire, and meter.
• Resistors, various.
• Transistor, 2N2222 or similar. Quantity: 1.
A transistor can switch a flow of electricity, just like a relay. But it’s much more
sensitive and versatile, as this first ultra-simple experiment will show.
We’ll start with the 2N2222 transistor, which is the most widely used semi-
conductor of all time (it was introduced by Motorola in 1962 and has been in
production ever since).
First, you should get acquainted with the transistor. Because Motorola’s pat-
ents on the 2N2222 ran out long ago, any company can manufacture their
own version of it. Some versions are packaged in a little piece of black plastic;
others are enclosed in a little metal “can.” (See Figure 2-83.) Either way, it con-
tains a piece of silicon divided into three sections known as the collector, the
base, and the emitter. I’ll describe their function in more detail in a moment,
but initially you just need to know that in this type of transistor, the collector
receives current, the base controls it, and the emitter sends it out.
Use your breadboard to set up the circuit shown in Figure 2-85. Be careful to
get the transistor the right way around! (See Figure 2-84.) For the three brands
I have mentioned in the shopping list, the flat side should face right, if the
transistor is packaged in black plastic, or the little tab should face toward the
lower left, if the transistor is packaged in metal.
Figure 2-85. The transistor blocks voltage that reaches it through R1.
But when pushbutton S1 is pressed, this tells the transistor to allow
current to pass through it. Note that transistors are always identified
with letter Q in wiring diagrams and schematics.
S1: Pushbutton, momentary, OFF (ON)
R1: 180Ω
R2: 10K
R3: 680Ω
Q1: 2N2222 or similar
D1: LED
S1
R2
R1
Q1
12v
DC
D1
R3
Figure 2-83. A typical transistor is pack-
aged either in a little metal can or a molded
piece of black plastic. The manufacturer’s
data sheet tells you the identities of the
three wire leads, relative to the flat side of
a black plastic transistor or the tab that
sticks out of a metal-can transistor.
Collector
Base
Emitter
Collector
Base
Emitter
Figure 2-84. The 2N2222 transistor may be
packaged in either of these formats. Left:
RadioShack or Fairchild. Right: STMicro-
electronics (note the little tab sticking out
at the lower-left side). If you use a different
brand, you’ll have to check the manufac-
turer’s data sheet. Insert the transistor in
your breadboard with the flat side facing
right, as seen from above, or the tab point-
ing down and to the left, seen from above.

Chapter 274
Initially, the LED should be dark. Now press the pushbutton and the LED should
glow brightly. Electricity is following two paths here. Look at the schematic in
Figure 2-86, which shows the same circuit more clearly. I’ve shown positive at
the top and negative at the bottom (the way most schematics do it) because it
helps to clarify the function of this particular circuit. If you view the schematic
from the side, the similarity with the breadboard layout is easier to see.
Through R1, voltage reaches the top pin (the collector) of the transistor. The
transistor only lets a tiny trickle of it pass through, so the LED stays dark. When
you press the button, voltage is also applied along a separate path, through R2
to the middle pin (the base) of the transistor. This tells the transistor to open
its solid-state switch and allow current to flow out through its third pin (the
emitter), and through R3, to the LED.
You can use your meter in volts DC mode to check the voltage at points in the
circuit. Keep the negative probe from the meter touching the negative voltage
source while you touch the positive probe to the top pin of the transistor, the
middle pin, and the bottom pin. When you press the button, you should see
the voltage change.
Fingertip Switching
Now here’s something more remarkable. Remove R2 and the pushbutton, and
insert two short pieces of of wire as shown in Figure 2-87. The upper piece of
wire connects with the positive voltage supply; the lower piece connects with
the middle pin of the transistor (its base). Now touch the tip of your finger to
the two wires. Once again, the LED should glow, although not as brightly as
before. Lick the tip of your finger, try again, and the LED should glow more
brightly.
Never UseTwo Hands
The fingertip switching demo is safe if the electricity passes just through your finger.
You won’t even feel it, because it’s 12 volts DC from a power supply of 1 amp or less.
But it’s not a good idea to put the finger of one hand on one wire, and the finger of
your other hand on the other wire. This would allow the electricity to pass through
your body. Although the chance of hurting yourself this way is extremely small, you
should never allow electricity to run through you from one hand to the other. Also,
when touching the wires, don’t allow them to penetrate your skin.
R1
R3
S1
Q1
R2
Figure 2-86. This shows the same circuit as
the breadboard diagram in Figure 2-85.

Your finger is conducting positive voltage to the base of the transistor. Even
though your skin has a high resistance, the transistor still responds. It isn’t just
switching the LED on and off; it is amplifying the current applied to its base.
This is an essential concept: a transistor amplifies any changes in current that
you apply to its base.
Check Figure 2-88 to see more clearly what’s happening.
If you studied the section “Background: Positive and negative” in Chapter 1,
you learned that there is really no such thing as positive voltage. All we re-
ally have is negative voltage (created by the pressure of free electrons) and
an absence of negative voltage (where there are fewer free electrons). But be-
cause the idea of a flow of electricity from positive to negative was so widely
believed before the electron was discovered, and because the inner workings
of a transistor involve “holes” which are an absence of electrons and can be
thought of as positive, we can still pretend that electricity flows from positive
to negative. See the following section,“Essentials: All about NPN and PNP tran-
sistors,”for more details.
R1
Q1
12v
DC
Finger
tip R3
D1
Figure 2-87
R1
Q1
R3
Finger
tip
Figure 2-88. These two diagrams show
the same components as before, with a
fingertip substituted for R2. Although only
a trickle of voltage now reaches the base
of the transistor, it’s enough to make the
transistor respond.

Chapter 276
Essentials
All about NPN and PNP transistors
A transistor is a semiconductor, meaning that sometimes it
conducts electricity, and sometimes it doesn’t. Its internal
resistance varies, depending on the power that you apply to
its base.
NPN and PNP transistors are bipolar semiconductors. They
contain two slightly different variants of silicon, and con-
duct using both polarities of carriers—holes and electrons.
The NPN type is a sandwich with P-type silicon in the mid-
dle, and the PNP type is a sandwich with N-type silicon in
the middle. If you want to know more about this terminol-
ogy, and the behavior of electrons when they try to cross an
NP junction or a PN junction, you’ll have to read a separate
source on this subject. It’s too technical for this book. All you
need to remember is:
• All bipolar transistors have three connections: Collec-
tor, Base, and Emitter, abbreviated as C, B, and E on the
manufacturer’s data sheet, which will identify the pins
for you.
• NPN transistors are activated by positive voltage on the
base relative to the emitter.
• PNP transistors are activated by negative voltage on the
base relative to the emitter.
In their passive state, both types block the flow of electricity
between the collector and emitter, just like an SPST relay in
which the contacts are normally open. (Actually a transistor
allows a tiny bit of current known as“leakage.”)
You can think of a bipolar transistor as if it contains a little
button inside, as shown in Figures 2-89 and 2-90. When the
button is pressed, it allows a large current to flow. To press
the button, you inject a much smaller current into the base
by applying a small voltage to the base. In an NPN transis-
tor, the control voltage is positive. In a PNP transistor, the
control voltage is negative.
NPN transistor basics
• To start the flow of current from collector to emitter,
apply a relatively positive voltage to the base.
• In the schematic symbol, the arrow points from base to
emitter and shows the direction of positive current.
• The base must be at least 0.6 volts“more positive”than
the emitter, to start the flow.
• The collector must be“more positive”than the emitter.
PNP transistor basics
• To start the flow of current from emitter to collector,
apply a relatively negative voltage to the base.
• In the schematic symbol, the arrow points from emitter
to base and shows the direction of positive current.
• The base must be at least 0.6 volts“more negative”than
the emitter, to start the flow.
• The emitter must be“more positive”than the collector.
B
C
E
Figure 2-89. You can think of a bipolar transistor as if it contains
a button that can connect the collector and the emitter. In an
NPN transistor, a small positive potential presses the button.
B
C
E
Figure 2-90. In a PNP transistor, a small negative potential has
the same effect. The arrows point in the direction of “positive
current flow.”

Essentials
All about NPN and PNP transistors (continued)
All-transistor basics
• Never apply a power supply directly across a transistor.
You can burn it out with too much current.
• Protect a transistor with a resistor, in the same way you
would protect an LED.
• Avoid reversing the connection of a transistor between
positive and negative voltages.
• Sometimes an NPN transistor is more convenient in a
circuit; sometimes a PNP happens to fit more easily.
They both function as switches and amplifiers, the only
difference being that you apply a relatively positive
voltage to the base of an NPN transistor, and a rela-
tively negative voltage to the base of a PNP transistor.
• PNP transistors are used relatively seldom, mainly
because they were more difficult to manufacture in the
early days of semiconductors. People got into the habit
of designing circuits around NPN transistors.
• Remember that bipolar transistors amplify current, not
voltage. A small fluctuation of current through the base
enables a large change in current between emitter and
collector.
• Schematics sometimes show transistors with circles
around them, and sometimes don’t. In this book, I’ll use
circles to draw attention to them. See Figures 2-91 and
2-92.
• Schematics may show the emitter at the top and the
collector at the bottom, or vice versa. The base may be
on the left, or on the right, depending on what was most
convenient for the person drawing the schematic. Be
careful to look carefully at the arrow in the transistor to
see which way up it is, and whether it is NPN or PNP.You
can damage a transistor by connecting it incorrectly.
• Transistors come in various different sizes and con-
figurations. In many of them, there is no way to tell
which wires connect to the emitter, the collector, or the
base, and some transistors have no part numbers on
them. Before you throw away the packaging that came
with a transistor, check to see whether it identifies the
terminals.
• If you forget which wire is which, some multimeters
have a function that will identify emitter, collector, and
base for you. Check your multimeter instruction book-
let for more details.
C
E
B
Figure 2-91. The symbol for an NPN transistor always has an ar-
row pointing from its base to its emitter. Some people include
a circle around the transistor; others don’t bother. The style of
the arrow may vary. But the meaning is always the same. The
top-left version is the one I use in this book.
C
E
B
Figure 2-92. The symbol for a PNP transistor always has an ar-
row pointing from its emitter to its base. Some people include
a circle around the transistor; others don’t bother. The style of
the arrow may vary. But the meaning is always the same. The
top-left version is the one I use in this book.

Chapter 278
Background
Transistor origins
Though some historians trace the origins of the transistor back to the inven-
tion of diodes (which allow electricity to flow in one direction while preventing
reversal of the flow), there’s no dispute that the first working transistor was
developed at Bell Laboratories in 1948 by John Bardeen, William Shockley, and
Walter Brattain (Figure 2-93).
Shockley was the leader of the team, who had the foresight to see how
potentially important a solid-state switch could be. Bardeen was the theorist,
and Brattain actually made it work. This was a hugely productive collabora-
tion—until it succeeded. At that point, Shockley started maneuvering to have
the transistor patented exclusively under his own name. When he notified his
collaborators, they were—naturally—unhappy about this idea.
A widely circulated publicity photograph didn’t help, in that it showed Shockley
sitting at the center in front of a microscope, as if he had done the hands-on
work, while the other two stood behind him, implying that they had played a
lesser role. In fact Shockley, as the supervisor, was seldom present in the labora-
tory where the real work was done.
The productive collaboration quickly disintegrated. Brattain asked to be trans-
ferred to a different lab at AT&T. Bardeen moved to the University of Illinois
to pursue theoretical physics. Shockley eventually left Bell Labs and founded
Shockley Semiconductor in what was later to become Silicon Valley, but his am-
bitions outstripped the capabilities of the technology of his time. His company
never manufactured a profitable product.
Eight of Shockley’s coworkers in his company eventually betrayed him by
quitting and establishing their own business, Fairchild Semiconductor, which
became hugely successful as a manufacturer of transistors and, later, integrated
circuit chips.
Figure 2-93. Photographs provided by the Nobel Foundation show, left to right, John
Bardeen, William Shockley, and Walter Brattain. For their collaboration in develop-
ment of the world’s first working transistor in 1948, they shared a Nobel prize in
1956.

Essentials
Transistors and relays
One limitation of NPN and PNP transistors is that they are naturally“off”until
you turn them“on.”They behave like a normally open pushbutton, which
conducts electricity only for as long as you hold it down. They don’t normally
behave like a normal on switch, which stays on until you apply a signal to turn
it off.
A relay offers more switching options. It can be normally open, normally closed,
or it can contain a double-throw switch, which gives you a choice of two“on”
positions. It can also contain a double-pole switch, which makes (or breaks) two
entirely separate connections when you energize it. Single-transistor devices
cannot provide the double-throw or double-pole features, although you can
design more complex circuits that emulate this behavior.
Here’s a list of transistor and relay characteristics.
Transistor Relay
Long-term reliability Excellent Limited
Configurable for DP and DT switching No Yes
Ability to switch large currents Limited Good
Able to switch alternating current (AC) Usually not Yes
Can be triggered by alternating current (AC) Usually not Optional
Suitability for miniaturization Excellent Very limited
Sensitive to heat High Moderate
Ability to switch at high speed Excellent Limited
Price advantage for low-voltage low-current Yes No
Price advantage for high-voltage high-current No Yes
Current leakage when“off” Yes No
The choice between relays or transistors will depend on each particular
application.

Chapter 280
Theory
See the current
If you want to get a more precise understanding of how a
transistor works, you should try this little test. It shows the
precise behavior and limits of the 2N2222 transistor that
you used in the previous experiment.
I’ve said that in an NPN transistor, the collector should
always be more positive than the emitter and that the base
should have a potential somewhere between those two
voltages. Figure 2-94 shows this rather vague relationship.
Now I want to substitute some numbers for these general
statements.
More
positive
More
negative
Somewhere
in between
C
B
E
Figure 2-94. The proper functioning of an NPN transistor re-
quires you to maintain these voltage relationships.
Take a look at the schematic in Figure 2-95, and check the
component values. Notice that the total resistance above
the transistor, from R1 + R2, is the same as the total resis-
tance below it, from R3 + R4. Therefore the potential on the
base of the transistor should be halfway between the two
extremes—until you use potentiometer P1 to adjust the
voltage of the base of the transistor up and down.
The two 180Ω resistors, R1 and R3, protect the transistor
from passing excessive current. The two 10K resistors, R2
and R4, protect the base when the potentiometer is turned
all the way up or all the way down.
I would like you to see what the transistor is doing by mea-
suring the amperage flowing into the base at the position
marked A1, and the total amperage flowing out through the
emitter at the position marked A2. To do this, it would be re-
ally helpful if you had two meters. As that may be impracti-
cal, the breadboard diagrams in Figures 2-96 and 2-97 show
how you can swap one meter between the two locations.
Remember that to measure milliamps, you have to pass
electricity through the meter. This means that the meter
must be inserted into the circuit, and whenever you remove
the meter, you have to remake the connection where the
meter was. The breadboard diagram shows how you can do
this. Fortunately, it’s very easy to remove and replace wires
in a breadboard. Where wires are connected to the potenti-
ometer, you may need to revert to using alligator clips.
Begin with the potentiometer turned about halfway
through its range. Measure at A1 and A2. Turn the potenti-
ometer up a bit, and measure current at the two locations
again. Following is a table showing some actual readings I
obtained at those two locations, using two digital meters
simultaneously.
Milliamps passing
through location A1
Milliamps passing
through location A2
0.01 1.9
0.02 4.9
0.03 7.1
0.04 9.9
0.05 12.9
0.06 15.5
0.07 17.9
0.08 19.8
0.09 22.1
0.10 24.9
0.11 26.0
0.12 28.3
There’s a very obvious relationship. The current emerging
from the emitter of the transistor, through location A2, is
about 24 times the current passing through location A1,
into the base. The ratio of current coming out from the
emitter of an NPN transistor to current going into the base
is known as the beta value for a transistor. The beta value
expresses the transistor’s amplifying power.
It’s a very constant ratio, until you push it a little too far. Above
0.12 mA, this particular transistor becomes“saturated,”mean-
ing that its internal resistance cannot go any lower.

Theory
See the current (continued)
In my little experiment, I found that the maximum cur-
rent at A2 was 33mA. A simple calculation using Ohm’s
Law showed me that this meant the transistor’s internal
resistance was near zero. This is why you should protect a
transistor with some additional resistance in the circuit. If
you don’t, its low internal resistance would allow a huge cur-
rent flow that would immediately burn it out.
What about the other end of its range? When it passes only
1.9 mA, the transistor has an internal resistance of around
6,000Ω. The conclusion is that depending how much cur-
rent you apply to this transistor, its internal resistance varies
between zero and 6,000Ω, approximately.
So much for the theory. Now what can we do with a transis-
tor that’s fun, or useful, or both? We can do Experiment 11!
Figure 2-95. This is basically the
same as the previous circuit,
with a potentiometer added and
the LED removed. Component
values:
R1: 180Ω
R2: 10K
R3: 180Ω
R4: 10K
P1: 1M linear potentiometer
Q1: 2N2222 transistor
A1
A2
12V
DC
R1
Q1
R3R4
R2
P1
R1
Q1
12v
DC
R3
R2
R4
Amps
A1
Figure 2-96. The meter is measuring current flowing from the
potentiometer into the base of the transistor at position A1
(see Figure 2-95).
R1
Q1
12v
DC
R3
R2
R4
Amps
A2
Figure 2-97. One end of resistor R3 has been unplugged from
the breadboard so that the meter now measures current
flowing out through the emitter of the transistor, into R3, at
position A2.

Chapter 282
You will need:
• AC adapter, breadboard, wire, and meter.
• Resistors, various.
• Capacitors, various.
• Transistor, 2N2222 or similar. Quantity: 2.
• 2N6027 programmable unijunction transistor (PUT). Quantity: 2.
• Miniature 8Ω loudspeaker. Quantity: 1.
So far, I’ve described small circuits that perform very simple functions. Now
it’s time to show how modules can be combined to create a device that does
a bit more.
The end product of this experiment will be a circuit that makes a noise like a
small siren, which could be used in an intrusion alarm. You may or may not
be interested in owning an alarm, but the four-step process of developing it
is important, because it shows how individual clusters of components can be
persuaded to communicate with each other.
I’ll begin by showing how to use a transistor to make a solid-state version of
the oscillating circuit that you built with a relay in Experiment 8. The relay, you
may remember, was wired in such a way that the coil received power through
the contacts of the relay. As soon as the coil was energized, it opened the con-
tacts, thus cutting off its own power. As soon as the contacts relaxed they re-
stored the power, and the process repeated itself.
There’s no way to do this with a single bipolar transistor.You actually need two
of them, switching each other on and off, and the way that this works is quite
hard to understand. An easier option is to use a different thing known as a
programmable unijunction transistor, or PUT.
Unijunction transistors were developed during the 1950s, but fell into disuse
when simple silicon chips acquired the ability to perform the same kinds of
functions, more accurately and more cheaply. However, the so-called pro-
grammable unijunction transistor is still widely available, often used in appli-
cations such as lamp dimmers and motor controllers. Because its primary use
is in generating a stream of pulses, it’s ideal for our purposes.
If you put together the components shown in Figure 2-98, the LED should start
flashing as soon as you apply power.
Note that this circuit will work on 6 volts. You won’t damage anything if you
run it with 12 volts, but as we continue adding pieces to it, you’ll find that
it actually performs better at 6 volts than at 12. If you read the next section,
“Essentials: All about programmable unijunction transistors,” you’ll find out
how the circuit works.
R1
R2
R3
Q1
C1
D1
6V
DC
Figure 2-98. Assemble these components,
apply power, and the LED should start
flashing.
R1: 470K
R2: 15K
R3: 27K
C1: 2.2 μF electrolytic capacitor
D1: LED
Q1: 2N6027 programmable unijunction
transistor

Essentials
All about programmable unijunction transistors
The schematic symbol for a programmable unijunction transistor, or PUT, looks
very different from the symbol for a bipolar transistor, and its parts are named
differently, too. Nevertheless, it does have a similar function as a solid-state
switch. The symbol and the names of the three connections are shown in Figure
2-99.
Note that this is a rare case (maybe the only one in the whole of electronics!) in
which you won’t run into confusing variations of the basic schematic symbol. A
PUT always seems to look the way I’ve drawn it here. Personally I think it would be
clearer if we added a circle around it, but no one seems to do that, so I won’t, either.
The 2N6027 is probably the most common PUT, and seems to be standardized
in its packaging and pin-outs. I’ve only seen it in a plastic module rather than
a little tin can. Figure 2-100 shows the functions of the leads if your 2N6027 is
manufactured by Motorola or On Semiconductor. If you have one from another
source, you should check the data sheet.
Note that the flat side of the plastic module faces the opposite way around
compared with the 2N2222 bipolar transistor, when the two devices are func-
tioning similarly.
The PUT blocks current until its internal resistance drops to allow flow from the
“anode”to the“cathode.”In this way, it seems very similar to an NPN transistor, but
there’s a big difference in the circumstances that cause the PUT to lower its resis-
tance. The voltage at the anode determines when the PUT allows current to flow.
Suppose you start with, say, 1 volt at the anode. Slowly, you increase this volt-
age. The transistor blocks it until the anode gets close to 6 volts. Suddenly this
pressure breaks down the resistance and current surges from the anode to the
cathode. If the voltage goes back down again, the transistor reverts to its origi-
nal state and blocks the flow.
I’ve included another version of the“finger on the button”drawing to convey
this concept. The voltage on the anode is itself responsible for pushing the but-
ton that opens the pathway to the cathode. See Figure 2-101.
Anode
Cathode
Gate
Figure 2-99. The schematic symbol for
a PUT.
Anode
Gate
Cathode
Figure 2-100. In PUTs manufactured by
On Semiconductor and Motorola, the
leads have these functions.

Chapter 284
Essentials
All about programmable unijunction transistors
(continued)
This may cause you to wonder what the function of the gate is. You can think of
it as“assisting”the finger on the button. In fact, the gate is the“programmable”
part of a PUT. By choosing a voltage for the gate, you establish the threshold
point when current starts to flow.
Here’s a simple take-home summary:
• The anode has to be more positive than the cathode, and the gate should
be between those two extremes.
• If anode voltage increases above a threshold point, current bursts through
and flows from the anode to the cathode.
• If anode voltage drops back down below the threshold, the transistor stops
the flow.
• The voltage you apply to the gate determines how high the threshold is.
• The gate voltage is adjusted with two resistors, shown as R1 and R2 in the
simple schematic in Figure 2-102. Typically, each resistor is around 20K. The
PUT is protected from full positive voltage by R3, which can have a high
value, 100K or greater, because very little current is needed to bias the
transistor.
• You add your input signal in the form of positive voltage at the anode.
When it exceeds the threshold, it flows out of the cathode and can work
some kind of output device.
The only remaining question is how we make a PUT oscillate, to create a stream
of on/off pulses. The answer is the capacitor that you included in the circuit that
you breadboarded at the beginning of Experiment 11.
GATE
ANODE
CATHODE
Figure 2-101. When voltage at the anode
of a PUT crosses a threshold (deter-
mined by a preset voltage at the gate),
current breaks through and surges from
the anode to the cathode. In this sense,
the anode voltage acts as if it presses a
button itself to open a connection inside
the PUT, with some assistance from
control voltage at the gate.
R2
R1 R3
Input
signal
Output
device
Figure 2-102. This simple schematic
shows how a PUT is used. R1 and R2
determine the voltage at the gate, which
sets the threshold point for the input at
the anode. Above the threshold, current
flows from anode to cathode.

Step 1: Slow-Speed Oscillation
Figure 2-103 is a schematic version of the previous PUT breadboard circuit
shown in Figure 2-98, drawn so that the layout looks as much like the bread-
board as possible.
15K
470K
27K
2N6027
2.2uF
6V
DC
Figure 2-103. This makes it easier to see what’s happening in the breadboard version.
The 15K resistor and 27K resistor establish the voltage at the gate. The 470K
resistor supplies the anode of the PUT, but the PUT begins in its“off”condition,
blocking the voltage. So the voltage starts to charge the 2.2 μF capacitor.
You may remember that a resistor slows the rate at which a capacitor accu-
mulates voltage. The bigger the resistor and/or the larger the capacitor, the
longer the capacitor takes to reach a full charge. In this circuit, the capacitor
takes about half a second to get close to 6 volts.
But notice that the PUT is connected directly with the capacitor. Therefore,
whatever voltage accumulates on the capacitor is also experienced by the
PUT. As the voltage gradually increases, finally it reaches the threshold, which
flips the PUT into its “on” state. The capacitor immediately discharges itself
through the PUT, through the LED (which flashes), and from there to the nega-
tive side of the power supply.
The surge depletes the capacitor. The voltage drops back down, and the PUT
returns to its original state. Now the capacitor has to recharge itself all over
again, until the whole process repeats itself.
If you substitute a 22 μF capacitor, the charge/discharge cycle should take
about 10 times as long, which will give you time to measure it. Set your me-
ter to measure volts DC and place its probes on either side of the capacitor.
You can actually watch the charge increasing until it reaches the threshold, at
which point the capacitor discharges and the voltage drops back down again.
So now we have an oscillator. What’s next?

Chapter 286
Step 2: Beyond the Persistence of Vision
If you substitute a much smaller capacitor, it will charge much more quickly,
and the LED will flash faster. Suppose you use a capacitor of 0.0047 μF (which
can also be expressed as 47 nanofarads, or 47 nF).This seems like an odd num-
ber, but it’s a standard value for a capacitor.This will reduce the capacitance by
a factor of more than 500, and therefore the LED should flash about 500 times
as fast, which should be about 1,000 times per second. The human eye cannot
detect such rapid pulses. The human ear, however, can hear frequencies up to
10,000 per second and beyond. If we substitute a miniature loudspeaker for
the LED, we should be able to hear the oscillations.
Figure 2-104 shows how I’d like you to make this happen. Please leave your
original, slow-flashing circuit untouched, and make a duplicate of it farther
down the breadboard, changing a couple of component values as indicated.
In the schematic in Figure 2-105, the new part of the circuit is in solid black,
while the previous section is in gray.
R1
R2
R3
Q1
C1
D1
R4
R5
R7
Q2
C2
L1
R6
6V
DC
Figure 2-104. The extra components which have been added at the lower half of the bread-
board have the same functions as the components at the top, but some values are slightly
different:
R4: 470K
R5: 33K
R6: 27K
R7: 100Ω
C2: 0.0047 μF
Q2: 2N6027
L1: 8Ω 1-inch loudspeaker
100
33K
15K
470K
27K
2.2uF
2N6027
2N6027
.0047uF
27K
470K
6V
DC
Figure 2-105. The previous section that you
built is shown in gray. Just add the new
section in black.

I want you to keep the slow-flashing circuit separately, untouched, because I
have an idea to make use of it a little later. You can leave the LED blinking.
The loudspeaker should be wired in series with a 100Ω resistor to limit the cur-
rent that flows out of the PUT.The loudspeaker doesn’t have any polarity, even
though it is fitted with a red wire and a black wire. You can connect it either
way around.
Initially, you may be disappointed, because the circuit will not seem to be do-
ing anything. However, if you place your ear very, very close to the loudspeak-
er, and if you wired the circuit correctly, you should hear a faint buzz, like a
mosquito. Obviously, this isn’t loud enough to serve any practical purpose. We
need to make it louder. In other words, we need to amplify it.
Maybe you remember that the 2N2222, which you played with previously, can
function as an amplifier. So let’s try using that.
Step 3: Amplification
Disconnect the loudspeaker and its 100Ω series resistor.Then add the 2N2222,
which is linked with the output from the PUT via a 1K resistor to protect it from
excessive current. See Figure 2-107.
The emitter of the 2N2222 is connected to ground, and the collector is sup-
plied through the loudspeaker and its 100Ω series resistor.This way, small fluc-
tuations in the output from the PUT are sensed by the base of the 2N2222
which converts them into bigger fluctuations between the collector and the
emitter, which draw current through the loudspeaker. Check the schematic in
Figure 2-108.
Now the sound should be louder than an insect buzz, but still not really loud
enough to be useful. What to do?
Well—how about if we add another 2N2222? Bipolar transistors can be placed
in series, so that the output from the first one goes to the base of the second
one.The 24:1 amplification of the first one is multiplied by another 24:1, giving
a total amplification of more than 500:1.
There are limits to this technique. The 2N2222 can only conduct so much cur-
rent before getting overloaded, and excess amplification can cause distortion.
But when I built this circuit, I used a meter to verify that we’re still within the
design limits of a 2N2222, and for this project, I don’t care whether the sound
is slightly distorted.
Background
Mounting a
loudspeaker
The diaphragm or cone of a
loudspeaker is designed to radi-
ate sound, but as it oscillates to
and fro, it emits sound from its
back side as well as its front side.
Because the sounds are opposite
in phase, they tend to cancel each
other out.
The perceived output from a
loudspeaker can increase dramati-
cally if you add a horn around it in
the form of a tube to separate the
output from the front and back
of the speaker. For a miniature
1-inch loudspeaker, you can bend
and tape a file card around it. See
Figure 2-106.
Better still, mount it in a box so
that the box absorbs the sound
from the rear of the loudspeaker.
For purposes of these simple
experiments, I won’t bother to go
into the details of vented enclo-
sures and bass-reflex designs.
Figure 2-106. A loudspeaker emits
sound from its bottom surface as
well as its top surface. To increase
the perceived audio volume, use
a cardboard tube to separate the
two sound sources, or mount the
speaker in a small box.

Chapter 288
R1
R2
R3
Q1
Q3
C1
D1
R4
R7
Q2
C2
L1
R8
R5
R6
6V
DC
Figure 2-107. By adding a 2N2222 general-purpose transistor, we amplify the signal
from Q2:
R8: 1K
Q3: 2N2222
Other components are the same as in the previous step in constructing this circuit.
100
33K
15K
470K
27K
2.2uF
.0047uF
27K
1K
470K
2N6027
2N6027
2N2222
6V
DC
Figure 2-108
Add the second 2N2222 as shown in Figure 2-109. In Figure 2-110, once again
the previously wired section is in gray.
If the accumulation of electrical components is beginning to seem confusing,
remember that each cluster of parts has a separate defined function. We can
draw a block diagram to illustrate this, as in Figure 2-112.
Using the second 2N2222, you should find that the output is more clearly
audible, at least within the limits of your tiny 1-inch loudspeaker. Cup your
hands around it to direct the sound, and you’ll find that the volume seems
to increase. You can also try using a 3-inch loudspeaker, which will create a
generally better audio output while still remaining within the limits of the little
2N2222 transistor. See Figure 2-106, shown previously, and Figure 2-111.

R1
R2
R3
Q1
Q3
Q4
C1
D1
R4
R9
R7
Q2
C2
L1
R5
R8
R6
6V
DC
Figure 2-109. Q4 is another 2N2222 transistor that further amplifies the signal. It receives
power through R9: 2.2K.
100
2K2
1K
2N6027
2N2222
2N2222
33K
15K
470K
27K
2.2uF
.0047uF
27K
470K
2N6027
6V
DC
Figure 2-110. This schematic is comparable
with the component layout in Figure 2-109.
Figure 2-111. The 2N2222 transistor is quite capable of driving a 3-inch loudspeaker, which
will create much better sound than a 1-inch speaker.

Chapter 290
Step 4: Pulsed Output
If you wanted to use this audio signal as some kind of an alarm, a steady dron-
ing noise is not very satisfactory. A pulsing output would be a much better
attention-getter.
Well, the first section of the circuit that you assembled created a pulsing signal
about twice per second. You used it to flash an LED. Maybe we can get rid of
the LED and feed the output from the first section to the second section. The
lower block diagram in Figure 2-112 explains this concept.
Can it really be that simple? Well, yes and no. The trick is to make the output
from the first section compatible with the input to the second section. If you
simply connect a wire from the cathode of the first PUT to the anode of the
second PUT, that’s not going to work, because the second PUT is already oscil-
lating nicely between low and high voltage, about 1,000 times each second.
Add more voltage, and you will disrupt the balance that enables oscillation.
However, remember that the voltage on the gate of a PUT affects its threshold
for conducting electricity. Maybe if we connect the output from Q1 to the gate
of Q2, we’ll be able to adjust that threshold automatically. The voltage still has
to be in a range that the PUT finds acceptable, though. We can try various re-
sistors to see which one works well.
This sounds like trial and error—and that’s exactly what it is. Doing the math
to predict the behavior of a circuit like this is far too complicated—for me, any-
way. I just looked at the manufacturer’s data sheet, saw the range of resistor
values that the PUT would tolerate, and chose one that seemed as if it should
work.
If you remove the LED and substitute R10 as shown in the breadboard diagram
in Figure 2-113, you’ll find that the fluctuating output from Q1 makes Q2 emit
a two-tone signal. This is more interesting, but still not what I want. I’m think-
ing that if I make the pulses out of Q1 less abrupt, the result could be better,
and the way to smooth a pulsing output is to hook up another capacitor that
will charge at the beginning of each pulse and then release its charge at the
end of each pulse. This is the function of C3 in Figure 2-114, and it completes
the circuit so that it makes a whooping sound almost like a“real”alarm.
If you don’t get any audio output, check your wiring very carefully. It’s easy to
make a wrong connection on the breadboard, especially between the three
legs of each transistor. Use your meter, set to DC volts, to check that each sec-
tion of the circuit has a positive voltage relative to the negative side of the
power supply.
Figure 2-115 shows how your circuit should actually look on the breadboard.
Power
Fast Oscillator
Amplifier
Loudspeaker
Slow Oscillator
Fast Oscillator
Amplifier
Loudspeaker
Power
Figure 2-112. Top: The basic functions of
the noisemaking oscillator circuit shown
as a block diagram. Bottom: The same
functions with a slow oscillator added to
control the fast oscillator.

R1
R2
R3
R10
R6
Q1
Q3
Q4
C1
C3
R4
R9
R7
Q2
C2
L1
R8
R5
6V
DC
Figure 2-113. R10 connects the slow-running oscillator at the top of the breadboard to the
gate of Q2, the PUT in the middle of the breadboard. This modulates the audio oscillator,
with addition of a smoothing capacitor.
100
2K2
33K
10K
15K
470K
27K
2.2uF
2.2uF
.0047uF
27K
1K
470K
2N2222
2N2222
2N6027
2N6027
6V
DC
Figure 2-114. This schematic shows the
same circuit as in Figure 2-113:
R10: 10K
C3: 2.2 μF
Figure 2-115. This photograph shows the complete alarm-audio circuit on a breadboard.

Chapter 292
Tweaking it
There’s still a lot of room for creativity here:
• Adjust the frequency of the sound: Use a smaller or larger capacitor in-
stead of C2 (half or twice the current value). Use a smaller or larger value
for R5.
• Adjust the pulsing feature: Use a smaller or larger capacitor instead of C1
(half or twice the current value). Use a smaller or larger value for R2.
• General performance adjustments: try a larger value for R1. Try smaller or
larger values for C3.
• Try running the circuit at 7.5 volts, 10 volts, and 12 volts.
The circuits in this book are suggested as only a starting point. You should
always try to tweak them to make them your own. As long as you follow the
general rule of protecting transistors and LEDs with resistors, and respecting
their requirements for positive and negative voltage, you’re unlikely to burn
them out. Of course, accidents will happen—I myself tend to be careless, and
fried a couple of LEDs while working on this circuit, just because I connected
them the wrong way around.
Step 5: Enhancements
A noisemaking circuit is just the output of an alarm. You would need several
enhancements to make it useful:
1. Some kind of an intrusion sensor. Maybe magnetic switches for windows
and doors?
2. A way to start the sound if any one of the sensors is triggered. The way
this is usually done is to run a very small but constant current through
all of the switches in series. If any one switch opens, or if the wire itself is
broken, this interrupts the current, which starts the alarm.You could make
this happen with a double-throw relay, keeping the relay energized all the
time until the circuit is broken, at which point, the relay relaxes, opening
one pair of contacts and closing the other pair, which can send power to
the noisemaker.
The trouble is that a relay draws significant power while it’s energized, and
it also tends to get hot. I want my alarm system to draw very little current
while it’s in “ready” mode, so that it can be powered by a battery. Alarm
systems should never depend entirely on AC house current.
If we don’t use a relay, can we use a transistor to switch on the rest of the
circuit when the power is interrupted? Absolutely; in fact, one transistor
will do it.
3. But how do we arm the alarm in the first place? Really, we need a three-
step procedure. First, check a little light that comes on when all the doors
and windows are closed. Second, press a button that starts a 30-second
countdown, giving you time to leave, if that’s what you want to do. And
third, after 30 seconds, the alarm arms itself.

4. If the alarm is triggered, what then? If someone forces open a window,
should the alarm stop sounding as soon as the window is closed again?
No, the alarm should lock itself on, until you turn it off.
5. How do you turn it off? Some kind of secret-code keypad would be good.
6. But to avoid driving everyone crazy if the alarm is triggered when you’re
not there, it should eventually stop itself, perhaps after about 10 minutes.
At that point it should remain quiet but should light an LED to tell you
what happened. You can then press a reset button to switch off the LED.
Implementing the Wish List
I’ve compiled a wish list that seems likely to make the project at least five times
as complicated as it is already. Well, that’s what tends to happen when you go
beyond little demo circuits and try to design something that will be useful in
everyday life. Suddenly you find yourself having to accommodate all kinds of
circumstances and situations.
Actually, I can and will show you how to take care of all the enhancements on
the wish list, but I’m thinking that they will require us to get a little more seri-
ous about electronics projects in general first. If you’re going to build some-
thing ambitious, you’ll want to make it more permanent, and probably more
compact, than a breadboard with components pushed into it.
You will need to know how to connect everything permanently with solder, on
a piece of perforated board that you can install in a neat little project box with
switches and lights on the outside.
I’m going to deal with soldering and packaging in the next chapter. After that,
we’ll get back to the alarm project.

3
95
Getting Somewhat
More Serious
I don’t know how far you’ll want to delve into electronics, but I do know that
I’ve shown you about as much as I can with just a handful of components,
some wires, a breadboard, and a few tools. To continue, you’ll need:
• Some more tools and supplies
• Basic soldering skills
• Additional knowledge about:
-- Integrated circuits
-- Digital electronics
-- Microcontrollers
-- Motors
The tools are not particularly exotic or expensive, and the soldering skills are
easily acquired. Learning to join wires with solder is far easier than mastering
high-level crafts such as jewelry making or welding.
As for additional areas of knowledge about electronics, they are no more chal-
lenging than those that I have covered already.
By the end of this section, you should be able to transplant components from
a breadboard onto perforated board, where you will solder everything togeth-
er, and then mount the board in a little box with switches and warning lights
on the front, for everyday use.
Tools
Each of the following tools is rated Essential, Recommended, or Optional. The
Essential tools will take you through this chapter of the book. If you supple-
ment them with the Recommended tools, they should be sufficient to get you
to the end of the book. The Optional tools will make your work easier, but
whether they’re worth the money is for you to decide. Remember that URLs
for manufacturers and sources of supply are all listed in the appendix.
In this chapter
Experiment 12: Joining Two Wires Together
Experiment 13: Broil an LED
Experiment 14: A Pulsing Glow
Experiment 15: Intrusion Alarm Revisited

Chapter 396
I am assuming that you already have some commonly used workshop basics,
such as an electric drill.
Essential: Pencil-type 15-watt soldering iron
Examples are RadioShack part 64-2051, McMaster-Carr catalog item
7016A34, or Xytronic model 252. See Figure 3-1. Soldering irons rated at
15 watts are less common than those that deliver 25 watts or more. Still,
the 15-watt size is desirable for the small-scale work you’ll be doing, and
greatly reduces the risk of damaging components by inflicting excess
heat.
When comparing prices, remember that a plated tip, which costs a little
more, will last longer, will be easier to keep clean, and will conduct heat
more reliably than a plain copper tip. If the manufacturer’s specification
doesn’t mention a plated tip, the soldering iron probably doesn’t have
one.
Essential: General-duty soldering iron, 30 to 40 watts
Although most of the projects in this book entail small, heat-sensitive
components and thin wire, at some point you’re likely to want to make a
solder joint with larger components and/or thicker wire. A 15-watt solder-
ing iron will be unable to deliver enough heat.You should consider having
a larger soldering iron in reserve, especially because they are relatively
inexpensive.
Personally, I like the Weller Therma-Boost, shown in Figure 3-2, because
it has an extra button that delivers more heat on demand. This is useful
when you want the iron to get hot quickly, or if you are trying to solder
very thick wire, which absorbs a lot of heat.
If you can’t find or don’t like the Weller, almost any 30-watt or 40-watt sol-
dering iron will do. Check eBay or your local hardware store.
Essential: Helping hand
The so-called “helping hand” (or “third hand”) has two alligator clips that
hold components or pieces of wire precisely in position while you join
them with solder. Some versions of the“helping hand”also feature a mag-
nifying lens, a wire spiral in which you can rest your soldering iron, and a
little sponge that you use to clean the tip of your iron when it becomes
dirty. These additional features are desirable. Helping hands are available
from all electronics hobby sources. Examples are the catalog item HH55
from Elenco or model 64-2991 from RadioShack. See Figure 3-3.
Essential: Magnifying lens
No matter how good your eyes are, a small, handheld, powerful magnify-
ing lens is essential when you are checking solder joints on perforated
board. The three-lens set in Figure 3-4 is designed to be held close to your
eye, and is more powerful than the large lens on a “helping hand.” The
folding lens in Figure 3-5 stands on your workbench for hands-free opera-
tion. Both are available from RadioShack and similar items are stocked by
art supply stores and hobby shops. Plastic lenses are quite acceptable if
you treat them carefully.
Figure 3-1. The low wattage of this pencil-
style soldering iron enables you to use it
safely on sensitive components, and the
sharp tip helps to apply heat selectively.
Figure 3-2. This higher-wattage soldering
iron delivers the additional heat necessary
for thicker wire or larger components. The
discoloration quickly occurs as a result
of everyday use and has no effect on the
capability of the iron, as long as the tip of
it is clean.
Figure 3-3. The helping hand is fitted with
two alligator clips to hold your work. The
metal spiral is a safe place to holster a hot
soldering iron, and you use the sponge to
wipe its tip.

Getting Somewhat More Serious 97
Figure 3-4. As long as you treat it carefully,
a cheap set of plastic magnifying lenses is
perfectly acceptable. Handheld magnifica-
tion is essential for inspecting the solder
joints that you make on perforated board.
Figure 3-5. This kind of folding magni-
fier can stand on your desktop and is
useful for checking part numbers on tiny
components.
Essential: Clip-on meter test leads
The probes that came with your multimeter require you to hold them in
contact while you make a reading. This requires both hands, preventing
you from doing anything else at the same time.
When you use a pair of “minigrabber” probes with little spring-loaded
clips at the end, you can attach the Common (negative) lead from your
meter to the negative side of your circuit and leave it there, while you
touch or attach the positive probe elsewhere.
The Pomona model 6244-48-0 (shown in Figure 3-6) from Meter Superstore
and some other suppliers is what you need. If you have trouble finding it
or you object to the cost, you may consider making your own by buying a
couple of“banana plugs”(such as RadioShack part 274-721) that will fit the
sockets on your meter, and then use 16-gauge or thicker stranded wire to
connecttheplugswithICtestclips,suchasKobiconn13IC331orRadioShack
“mini hook clips,”part number 270-372C. See Figures 3-7 and 3-8.
Figure 3-6. These“minigrabber” add-ons for
meter leads make it much easier to measure
voltage or current. Push the spring-loaded
button, and a little copper hook slides out.
Attach it to a wire, release the button, and
you have your hands free for other tasks. It’s
a mystery that meters are not supplied with
these grabbers as standard equipment.
Figure 3-7. To make your own minigrabber
meter leads, first attach a banana plug to
a wire by sliding the wire through the cap,
into the plug, and out through a hole in
the side.
Figure 3-8. Then screw a collar over the
protruding piece of wire, and screw on the
cap. The other end of the wire is soldered to
a probe.

Chapter 398
Essential: Heat gun
After you join two wires with solder, you often need to insulate them.
Electrical tape, sometimes called insulating tape, is messy and tends to
come unstuck. You’ll be using heat-shrink tube, which forms a safe, per-
manent sheath around a bare-metal joint. To make the tube shrink, use a
heat gun, which is like a very powerful hair dryer. They’re available from
any hardware supply source, and I suggest you buy the cheapest one you
can find. See Figure 3-9.
Essential: Solder pump
This little gadget sucks up hot, melted solder when you are trying to re-
move a solder joint that you made in the wrong place. Available from All
Electronics (catalog item SSR-1) or RadioShack 64-2086. See Figure 3-10.
Essential: Desoldering wick
Also known as desoldering braid. See Figure 3-11. You use this to soak up
solder, in conjunction with the Solder Pump. Available from All Electronics
(catalog item SWK) or RadioShack (part 64-2090).
Essential: Miniature screwdriver set
Dinky little electronic parts often have dinky little screws in them, and if
you try to use the wrong size of screwdriver, you’ll tend to mash the heads
of the screws. I like the Stanley precision set, part number 66-052, shown
in Figure 3-12. But any set will do as long as it has both small Phillips and
straight-blade screwdrivers.
Recommended: Soldering stand
Like a holster for a gun, you rest your soldering iron in this stand when
the iron is hot but not on use. Examples are catalog item 50B-205 from All
Electronics, RadioShack model 64-2078, or check eBay. See Figure 3-13.
This item may be built into the helping hand, but you need an extra one
for your second soldering iron.
Figure 3-10. To remove a
solder joint, you can heat the
solder until it’s liquid, then
suck it up into this squeezable
rubber bulb.
Figure 3-11. An additional op-
tion for removing liquid solder
is to soak it up in this copper
braid.
Figure 3-12. A set of small
screwdrivers is essential.
Figure 3-13. A safe and simple
additional stand for a hot
soldering iron.
Figure 3-9. Like an overpowered hair dryer,
the heat gun is used with heat-shrink
tubing to create a snug, insulated sheath
around bare wire.

Recommended: Miniature hand saw
I assume that you will want to mount a finished electronics project in a de-
cent-looking enclosure. Consequently, you are likely to need tools to cut,
shape, and trim thin plastic. For example, you may want to cut a square
hole so that you can mount a square power switch in it.
Power tools are not suitable for this kind of delicate work. A miniature
handsaw (a.k.a. a “hobby saw”) is ideal for trimming things to fit. X-Acto
makes a range of tiny saw blades. I suggest the #15 blade, plus the handle
that it fits in, shown in Figure 3-14. Available online from Tower Hobbies,
Hobbylinc, ArtCity, and many other arts/crafts sources. Also look for the
larger X-Acto saw blade, #234 or #239, which you can use for cutting per-
forated board.
Recommended: Miniature vise
A miniature vise can do things that the helping hand cannot. I use mine
when I’m sawing small pieces of plastic and as a dead weight to anchor a
piece of perforated board while I’m working on it. See Figure 3-15.
Look for a cast-iron vise that is listed as being 1 inch or slightly larger, avail-
able from Megahobby, eBay, and other arts/crafts sources. Also consider
the PanaVise, which has a tilting head to allow you to turn your work to
any angle.
Recommended: Deburring tool
A deburring tool instantly smoothes and bevels any rough edge (when you
have sawn or drilled a piece of plastic, for instance) and also can enlarge
holes slightly.This may be necessary because some components are manu-
factured to metric sizes, which don’t fit in the holes that you drill with Ameri-
can bits.Your small local hardware store may not stock deburring tools, but
they are very inexpensively available from Sears, McMaster-Carr, KVMTools,
or Amazon. See Figure 3-16.
Optional: Hand-cranked countersink
You need a countersink to bevel the edges of screw holes to accept flat-
headed screws. If you use a countersink bit in an electric drill, it won’t give
you precise control when you’re working with thin, soft plastic.
Handheld countersinks that you grasp and turn like a screwdriver are easy
to find, but McMaster-Carr (catalog item 28775A61) is the only source I’ve
found for a hand-cranked tool that is much quicker to use. It comes with a
set of bits, as shown in Figure 3-17.
Optional: Pick and hook set
Made by Stanley, part number 82-115, available from Amazon and hard-
ware stores. You can find imported imitations for a few dollars less. See
Figure 3-18.
Optional: Calipers
These may seem like a luxury, but are useful for measuring the external
diameter of a round object (such as the screw thread on a switch or a po-
tentiometer) or the internal diameter of a hole (into which you may want
a switch or potentiometer to fit).
Figure 3-14. X-Acto makes a range of
small saw blades that are ideal for cutting
square holes to mount components in
plastic panels.
Figure 3-15. This one-inch vise is available
from the McMaster-Carr catalog.
Figure 3-16. This cunning little blade,
safety-tipped with a round bump on the
end, removes rough edges from saw cuts
with a single stroke, and can enlarge holes
that are almost big enough—but not quite.

Chapter 3100
I like Mitutoyo calipers, and the low-end model 505-611 (shown in Figure
3-19) does everything I need.You can find cheaper brands, but economiz-
ing on precision measuring tools may not be a wise policy in the long
term. The manufacturer’s site will show you all their available models, af-
ter which you can Google“Mitutoyo”to find retail sources.
Figure 3-17. You spin this countersink tool
like a hand crank to add just the right
amount of bevel to a hole, so that it will
accommodate a flat-head screw.
Figure 3-18. This pick-and-hook set is use-
ful in many unexpected ways.
Figure 3-19. Calipers can be digital (which
automatically convert from millimeters to
1/64 inch to 1/1,000 inch), or analog like
these (so you never need to worry about a
dead battery).
Supplies
Solder
This is the stuff that you will melt to join components together on a per-
manent (we hope) basis. You need some very thin solder, size 0.022 inches,
for very small components, and thicker solder, 0.05 inches, for heavier items.
Avoid buying solder that is intended for plumbers, or for craft purposes such
ascreatingjewelry.ArangeofsolderthicknessesisshowninFigure3-20.You
want to make sure to get lead-free solder.
Electronics solder has a nonacidic rosin core that is appropriate for elec-
tronic components. Rolls of solder are available from all hobby-electronics
sources including All Electronics, RadioShack, and Jameco, or search for
“electronic solder”on Amazon.
Wire
You’ll need some stranded wire to make flexible external connections
with the circuit that you’ll be building. Look for 22-gauge stranded hook-
up wire, in red, black, and green, 10 feet (minimum) of each.
If you want to install the intrusion alarm after completing that project in
Experiment 15, you’ll need white-insulated two-conductor wire of the
type sold for doorbells or furnace controls. This is available by the foot
Figure 3-20. Spools of solder in various
thicknesses.

from Lowe’s, Home Depot, Ace Hardware, and similar stores. You’ll decide
how much to buy after you measure the distances between the magnetic
sensor switches that you decide to install.
Heat-shrink tube
For use in conjunction with your heat gun, described previously. You’ll
need a range of sizes in any colors of your choice. See Figure 3-21. Check
RadioShack part 278-1627, other electronics suppliers, or your local hard-
ware store. Prices will vary widely. You can buy the cheapest.
Copper alligator clips
These absorb heat when you are soldering delicate components. The
Mueller BU-30C is a full-size solid copper alligator clip for maximum heat
absorption. RadioShack sells smaller clips (part number 270-373, shown
in Figure 3-22) that are suitable for tiny components.
Figure 3-21. Slide heat-shrink tubing over a
bare joint and apply heat from a heat gun
to make a tight insulating seal around the
joint.
Figure 3-22. These small clips absorb
heat to protect components when you’re
soldering them.
Perforated board
When you’re ready to move your circuit from a breadboard to a more per-
manent location, you’ll want to solder it to a piece of perforated board,
often known as“prototyping board”but also called“perfboard.”
You need the type that has copper strips etched onto the back, in ex-
actly the same “breadboard layout” as the conductors hidden inside a
breadboard, so that you can retain the same layout of your components
when you solder them into place. Examples are RadioShack part 276-150
(shown in Figure 3-23) for small projects and part 276-170 (in Figure 3-24)
for larger projects, such as Experiment 15.
For very small projects in which you will connect components using their
wires alone, you need perfboard that isn’t etched with copper strips con-
necting the holes. I like the Twin Industries 7100 range (available from
Mouser.com) or Vectorboard from Newark Electronics, shown in Figure
3-25. You use a saw to cut out as small a piece as you need. Cheaper op-
tions are RadioShack part 276-147 (shown in Figure 3-26), or PC-1 from All
Electronics. These have little copper circles around each hole that are not
necessary for our purposes, but not a problem, either.
Figure 3-23. This perforated board has a
pattern of copper traces similar to the
pattern inside a breadboard, so that you
can lay out the components with minimal
risk of wiring errors, when you’re ready to
create a permanently soldered version of
your project.

Chapter 3102
Figure 3-24. A larger example of perforated
board with breadboard geometry.
Figure 3-25. Plain perforated board (with
no copper traces) can be used for mount-
ing components when you want to do
point-to-point wiring.
Figure 3-26. A small piece of perforated
board with individual copper solder pads
to assist you in mounting components.
Plywood
When you use a soldering iron, hot drops of solder tend to fall onto your
table or workbench. The solder solidifies almost instantly, can be difficult
to remove, and will leave a scar. Consider using a 2-foot square of half-inch
plywood to provide disposable protection. You can buy it precut at Home
Depot or Lowe’s.
Machine screws
To mount components behind a panel, you need small machine screws
(or“bolts”). They look nice if they have flat heads that fit flush against the
panel. I suggest stainless-steel machine screws, #4 size, in 1/2-, 5/8-, 3/4-,
and 1-inch lengths, 100 of each, plus 400 washers and 400 #4 locknuts
of the type that have nylon inserts, so that they won’t work loose. Check
McMaster-Carr for a large and reasonably priced selection.
Project boxes
A project box is just a small box (usually plastic) with a removable lid. You
mount your switches, potentiometers, and LEDs in holes that you drill
through the box, and you attach your circuit on a perforated board that
goes inside the box. Search All Electronics for“project box”or RadioShack
for“project enclosure.”
You need a box measuring approximately 6 inches long, 3 inches wide,
and 2 inches high, such as RadioShack part 270-1805. Anything similar
will do. I suggest you buy a couple other sizes as well, as they will be use-
ful in the future.

Components
Power plugs, sockets, and binding posts
After you finish a project and put it in a box, you’ll need a convenient way
to supply it with power. Buy yourself a pair of insulated binding posts, such
as RadioShack part 274-661, shown in Figure 3-27. Also obtain a panel-
mounted power jack, size N, such as RadioShack part 274-1583, and DC
power plug, size N, such as RadioShack 274-1573. The plug-and-socket
pair is pictured in Figure 3-28.
Finally, you will need interconnects that are sized to fit a perforated board
that is drilled at intervals of 1/10 inch. Sometimes known as“single inline
sockets and headers,” but also known as “boardmount sockets and pin-
strip headers,” they come in strips of 36 or more, and you can snip off as
many as you need. Examples are Mill-Max part numbers 800-10-064-10-
001000 and 801-93-050-10-001000, or 3M part numbers 929974-01-36-
RK and 929834-01-36-RK. You can buy them from the usual electronics
suppliers. Figure 3-29 shows headers before and after being snapped into
small sections. Make sure that the interconnects have a terminal spacing
of 0.1 inch.
Battery
After you complete Experiment 15 at the end of this section of the book,
if you want to use the project on a practical basis, you’ll need a 12-volt
battery. Search online for “12v battery” and you’ll find many sealed, re-
chargeable lead-acid batteries that are designed for alarm systems, some
measuring as small as 1×2×3-inch and costing under $10. You need a
charger with it, which will probably cost you about $10.
Switches and relays
You will need the same DPDT relay and the same SPDT toggle switch that
were mentioned in Chapter 2 shopping list.
For Experiment 15, you’ll need magnetic switches that you can apply to
doors or windows, such as the Directed model 8601, available from doz-
ens of sources online.
Also you will need a DPDT pushbutton switch, ON-(ON) type, with
solder terminals. Examples are model MPG206R04 by Tyco or model
MB2061SS1W01-RO by NKK (with optional cap). Or search eBay for“DPDT
pushbutton.”
Diodes
Buy at least half-a-dozen red 5 mm LEDs rated for approximately 2 volts,
such as the Optek part number OVLFR3C7, Lumex part number SSL-LX-
5093IT, or Avago part HLMP-D155. Buy half-a-dozen similar green LEDs at
the same time.
In addition, you’ll need a signal diode, type 1N4001 (any brand will do).
Figure 3-30 shows an example, highly magnified.They’re cheap, and likely
to be useful in the future, so buy 10 of them.
Figure 3-27. These terminals, also known
as binding posts, enable a solderless con-
nection with wires that have stripped ends.
Also available in black.
Figure 3-28. The socket on the right can be
mounted in a project box to receive power
from the plug on the left.
Figure 3-29. Single inline sockets (top) and
headers (middle) allow you to make very
compact plug-and-socket connections
to a PC board. They can be sawn, cut, or
snapped into smaller sections (bottom).
The terminals are 0.1 inch apart.
Figure 3-30. This 1N4001 diode is about
1/4 inch long and can handle up to 50
volts.

Chapter 3104
Loudspeaker
To complete the project in Experiment 15, you’ll need a loudspeaker small
enough to fit inside your project box but louder than the 1-inch speaker
that you used previously. It should be 2 inches or 2.5 inches (50 to 60 mm)
in diameter. If you can find a 100Ω speaker, it will give you more output,
but an 8Ω speaker will be acceptable.
Your adventure into soldering begins with the prosaic task of joining one wire
to another, but will lead quickly to creating a full electronic circuit on perfo-
rated board. So let’s get started!
You will need:
• 30-watt or 40-watt soldering iron
• 15-watt pencil-type soldering iron
• Thin solder (0.022 inches or similar)
• Medium solder (0.05 inches or similar)
• Wire strippers and cutters
• “Helping hand”gadget to hold your work
• Shrink-wrap tubing, assorted
• Heat gun
• Something to protect your work area from drops of solder
Your First Solder Joint
We’ll start with your general-duty soldering iron—the one rated for 30 or 40
watts. Plug it in, leave it safely in its holder, and find something else to do for
five minutes. If you try to use a soldering iron without giving it time to get fully
hot, you will not make good joints.
Strip the insulation from the ends of two pieces of 22-gauge solid wire and
clamp them in your helping hand so that they cross each other and touch each
other, as shown in Figure 3-31.
To make sure that the iron is ready, try to melt the end of a thin piece of solder
on the tip of the iron. The solder should melt instantly. If it melts slowly, the
iron isn’t hot enough yet.
Soldering Irons Get Hot!
Please take these basic precautions:
Use a proper stand (such as the one
incorporated in your helping hands)
to hold your soldering iron. Don’t
leave it lying on a workbench.
If you have infants or pets, remember
that they may play with, grab, or
snag the wire to your soldering iron.
They could injure themselves (or you).
Be careful never to rest the hot tip
of the iron on the power cord that
supplies electricity to the iron. It can
melt the plastic in seconds and cause
a dramatic short circuit.
If you drop a soldering iron, don’t be
a hero and try to catch it. Most likely
you will grab the hot part, which
hurts. (I speak from experience.)
When you burn your hand, you will
instinctively let go of the iron, so you
may as well let it drop freely without
the intermediate step of burning
yourself while it’s on its way to the
floor. Naturally, you should pick it
up quickly after it does hit the floor,
but by then you will have gained the
necessary time in which to make a
sensible decision to grab it by the
cool end.
Always bear in mind that others in
your home are more at risk of hurting
themselves on a soldering iron than
you are, because they won’t know
that it’s hot. Most soldering irons
have no warning lights to tell you
that they’re plugged in. As a general
rule, always assume that a soldering
iron is hot, even if it’s unplugged. It
may retain sufficient heat to burn
you for longer than you expect.

Now follow these steps (shown in Figures 3-32 through 3-36):
1. Make sure the tip of the soldering iron is clean (wipe it on the moist-
ened sponge in the base of your helping hand if necessary), then touch
it against the intersection of the wires steadily for three seconds to heat
them. If you have hard tap water, use distilled water to wet the sponge to
avoid a buildup of mineral deposits on the tip of your soldering iron.
2. While maintaining the iron in this position, feed a little solder onto the in-
tersection of the wires, also touching the tip of the soldering iron. Thus, the
two wires, the solder, and the tip of the iron should all come together at one
point.The solder should spread over the wires within another two seconds.
3. Remove the iron and the solder. Blow on the joint to cool it. Within 10
seconds, it should be cool enough to touch.
4. Unclamp the wires and try to tug them apart. Tug hard! If they defeat
your best attempts to separate them, the wires are electrically joined and
should stay joined. If you didn’t make a good joint, you will be able to
separate the wires relatively easily, probably because you didn’t apply
enough heat or enough solder to connect them.
The reason I asked you to begin by using the higher-powered soldering iron is
that it delivers more heat, which makes it easier to use.
Figure 3-32 Figure 3-33 Figure 3-34
Figure 3-35. This and the preceding three
figures illustrate four steps to making a
solder joint: apply heat to the wires, bring
in the solder while maintaining the heat,
wait for the solder to start to melt, and
wait a moment longer for it to form a com-
pletely molten bead. The whole process
should take between 4 and 6 seconds.
Figure 3-36. The completed joint should be
shiny, uniform, and rounded in shape.
Figure 3-31. A helping hand work aid is
shown here holding two wires with their
stripped ends touching. The magnifying
glass has been hinged out of the way.

Chapter 3106
Background
Soldering myths
Myth #1: Soldering is very difficult.
Millions of people have learned how to do it, and statis-
tically, you are unlikely to be less coordinated than all
of them. I have a lifelong problem with a tremor in my
hands that makes it difficult for me to hold small things
steadily. I also get impatient with repetitive detail work.
If I can solder components, almost anyone should be
able to.
Myth #2: Soldering involves poisonous chemicals.
Modern solder contains no lead. You should avoid
inhaling the fumes for prolonged periods, but that also
applies to everyday products such as bleach and paint.
If soldering was a significant health hazard, we should
have seen a high death rate among electronics hobby-
ists decades ago.
Myth #3: Soldering is hazardous.
A soldering iron is less hazardous than the kind of iron
that you might use to iron a shirt, because it delivers
less heat. In fact, in my experience, soldering is safer
than most activities in a typical home or basement
workshop. That doesn’t mean you can be careless!
Soldering alternatives
As recently as the 1950s, connections inside electronic ap-
pliances such as radio sets were still being hand-soldered by
workers on production lines. But the growth of telephone
exchanges created a need for a faster way to make large
numbers of rapid, reliable point-to-point wiring connec-
tions, and“wire wrap”became a viable alternative.
In a wire-wrapped electronics project, components are
mounted on a circuit board that has long, gold-plated,
sharp-cornered square pins sticking out of the rear. Special
silver-plated wire is used, with an inch of insulation stripped
from its ends. A manual or power-driven wire-wrap tool
twirls the end of a wire around one of the pins, applying
sufficient tension to“cold-weld”the soft silver plating of
the wire to the pin. The wrapping process exerts sufficient
pressure to make a very reliable joint, especially as 7 to 9
turns of wire are applied, each turn touching all four corners
of the pin.
During the 1970s and 1980s, this system was adopted by
hobbyists who built their own home computers. A wire-
wrapped circuit board from a hand-built computer is shown
in Figure 3-37. The technique was used by NASA to wire the
computer in the Apollo spacecraft that went to the moon,
but today, wire-wrapping has few commercial applications.
The widespread industrial use of“through-hole”compo-
nents, such as the chips on early desktop computers, en-
couraged development of wave soldering, in which a wave
or waterfall of molten solder is applied to the underside of a
preheated circuit board where chips have been inserted. A
masking technique prevents the solder from sticking where
it isn’t wanted.
Today, surface-mount components (which are significantly
smaller than their through-hole counterparts) are glued to
a circuit board with a solder paste, and the entire assembly
is then heated, melting the paste to create a permanent
connection.
Figure 3-37. This picture shows some of the wire-wrapping in
Steve Chamberlin’s custom-built, retro 8-bit CPU and com-
puter. “Back in the day,” connecting such a network of wires
with solder joints would have been unduly time-consuming and
prone to faults. Photo credit: Steve Chamberlin.

Tools
Eight most common soldering errors
1. Not enough heat.
The joint looks OK, but because you didn’t apply quite
enough heat, the solder didn’t melt sufficiently to
realign its internal molecular structure. It remained
granular instead of becoming a solid, uniform blob,
and you end up with a“dry joint,”also known as a“cold
joint,”which will come apart when you pull the wires
away from each other. Reheat the joint thoroughly and
apply new solder.
A leading cause of underheated solder is the tempta-
tion to use the soldering iron to carry solder to the
joint. This results in the cold wires reducing the tem-
perature of the solder. What you should do is touch the
soldering iron to heat the wires first, and then apply
the solder. This way, the wires are hot and help to melt
the solder, which wants to stick to them.
Because this is such a universal problem, I’ll repeat
myself: Never melt solder on the tip of the iron and then
use it to carry the solder to the joint.
You don’t want to put hot solder on cold wires. You
want to put cold solder on hot wires.
2. Too much heat.
This may not hurt the joint, but can damage everything
around it. Vinyl insulation will melt, exposing the wire
and raising the risk of short circuits. You can easily dam-
age semiconductors, and may even melt the internal
plastic components of switches and connectors.
Damaged components must be desoldered and re-
placed, which will take time and tends to be a big hassle
(see“Tools: Desoldering”on page 109 for advice).
3. Not enough solder.
A thin connection between two conductors may not be
strong enough. When joining two wires, always check
the underside of the joint to see whether the solder
penetrated completely.
4. Moving the joint before the solder solidifies.
You may create a fracture that you won’t necessarily
see. It may not stop your circuit from working, but at
some point in the future, as a result of vibration or
thermal stresses, the fracture can separate just enough
to break electrical contact. Tracking it down will then
be a chore. If you clamp components before you join
them, or use perforated board to hold the components
steady, you can avoid this problem.
5. Dirt or grease.
Electrical solder contains rosin that cleans the metal
that you’re working with, but contaminants can still
prevent solder from sticking. If any component looks
dirty, clean it with fine sandpaper before joining it.
6. Carbon on the tip of your soldering iron.
The iron gradually accumulates flecks of black car-
bon during use, and they can act as a barrier to heat
transfer. Wipe the tip of the iron on the little sponge
mounted in the base of your soldering iron stand or
your helping hand.
7. Inappropriate materials.
Electronic solder is designed for electronic compo-
nents. It will not work with aluminum, stainless steel, or
various other metals. You may be able to make it stick
to chrome-plated items, but only with difficulty.
8. Failure to test the joint.
Don’t just assume that it’s OK. Always test it, by apply-
ing manual force if you can (see Figures 3-38 and 3-39
for the ideal protocol) or, if you can’t get a grip on the
joint, slip a screwdriver blade under it and flex it just
a little, or use small pliers to try to pull it apart. Don’t
be concerned about ruining your work. If your joint
doesn’t survive rough treatment, it wasn’t a good joint.
Of the eight errors, dry/cold joints are by far the worst,
because they are easy to make and can look OK.
Figure 3-38. Test result of
a bad solder joint.
Figure 3-39. Test result of a good
solder joint.

Chapter 3108
Your Second Solder Joint
Time now to try your pencil-style soldering iron. Once again, you must leave it
plugged in for a good five minutes to make sure it’s hot enough. In the mean-
time, don’t forget to unplug your other soldering iron, and put it somewhere
safe while it cools.
This time I’d like you to align the wires parallel with each other. Joining them
this way is a little more difficult than joining them when they cross each other,
but it’s a necessary skill. Otherwise, you won’t be able to slide heat-shrink tub-
ing over the finished joint to insulate it.
Figures 3-40 through 3-44 show a successful joint of this type. The two wires
do not have to make perfect contact with each other; the solder will fill any
small gaps. But the wires must be hot enough for the solder to flow, and this
can take an extra few seconds when you use the low-wattage pencil-style iron.
Be sure to feed the solder in as shown in the pictures. Remember: don’t try
to carry the solder to the joint on the tip of the iron. Heat the wires first, and
then touch the solder to the wires and the tip of the iron, while keeping it in
contact with the wires. Wait until the solder liquifies, and you will see it run-
ning eagerly into the joint. If this doesn’t happen, be more patient and apply
the heat for a little longer.
Figure 3-43. This and the preceding three
figures show how joining two wires that
are parallel is more difficult, and the
low-wattage, pencil-type soldering iron will
require longer to heat them sufficiently for
a good joint. Thinner solder can be used.
Figure 3-44. The finished joint has enough
solder for strength, but not so much solder
that it will prevent heat-shrink tubing from
sliding over it.

Theory
Soldering theory
The better you understand the process of soldering, the easier it should be for
you to make good solder joints.
The tip of the soldering iron is hot, and you want to transfer that heat into the
joint that you are trying to make. In this situation, you can think of the heat as
being like a fluid. The larger the connection is between the soldering iron and
the joint, the greater the quantity of heat, per second, that can flow through it.
For this reason, you should adjust the angle of the soldering iron so that it
makes the widest possible contact. If it touches the wires only at a tiny point,
you’ll limit the amount of heat flow. Figures 3-45 and 3-46 illustrate this con-
cept. Once the solder starts to melt, it broadens the area of contact, which helps
to transfer more heat, so the process accelerates naturally. Initiating it is the
tricky part.
The other aspect of heat flow that you should consider is that it can suck heat
away from the places where you want it, and deliver it to places where you
don’t want it. If you’re trying to solder a very heavy piece of copper wire, the
joint may never get hot enough to melt the solder, because the heavy wire
conducts heat away from the joint. You may find that even a 40-watt iron isn’t
powerful enough to overcome this problem, and if you are doing heavy work,
you may need a more powerful iron.
As a general rule, if you can’t complete a solder joint in 10 seconds, you aren’t
applying enough heat.
Figure 3-45. With only a small surface
area of contact between the iron and
the working surface, an insufficient
amount of heat is transferred.
Figure 3-46. A larger area of contact
between the soldering iron and its target
will greatly increase the heat transfer.
Tools
Desoldering
Desoldering is much, much harder
than soldering. Two simple tools
are available:
• Suction pump. First, you apply
the soldering iron to make the
solder liquid. Then you use
this simple gadget to try to
suck up as much of the liquid
as possible. Usually it won’t re-
move enough metal to allow
you to pull the joint apart, and
you will have to try the next
tool. Refer back to Figure 3-10.
• Desoldering wick or braid.
Desoldering wick, also known
as braid, is designed to soak
up the solder from a joint, but
again, it won’t clean the joint
entirely, and you will be in the
awkward position of trying to
use both hands to pull com-
ponents apart while simulta-
neously applying heat to stop
the solder from solidifying.
Refer back to Figure 3-11.
I don’t have much advice about
desoldering. It’s a frustrating experi-
ence (at least, I think so) and can
damage components irrevocably.

Chapter 3110
Adding Insulation
After you’ve succeeded in making a good inline solder connection between
two wires, it’s time for the easy part. Choose some heat-shrink tubing that is
just big enough to slide over the joint with a little bit of room to spare.
Figure 3-47. Other members of your family should understand that although a heat gun
looks like a hair dryer, appearances may be deceptive.
Slide the tubing along until the joint is centered under it, hold it in front of
your heat gun, and switch on the gun (keeping your fingers away from the
blast of superheated air). Turn the wire so that you heat both sides. The tubing
should shrink tight around the joint within half a minute. If you overheat the
tubing, it may shrink so much that it splits, at which point you must remove
it and start over. As soon as the tubing is tight around the wire, your job is
done, and there’s no point in making it any hotter. Figures 3-48 through 3-50
show the desired result. I used white tubing because it shows up well in photo-
graphs. Different colors of heat-shrink tubing all perform the same way.
Figure 3-48. Slip the tubing over your wire
joint.
Figure 3-49. Apply heat to the tubing. Figure 3-50. Leave the heat on the tubing
until it shrinks to firmly cover the joint.
Heat Guns Get Hot,Too!
Notice the chromed steel tube at the
business end of your heat gun. Steel
costs more than plastic, so the manu-
facturer must have put it there for a
good reason—and the reason is that
the air flowing through it becomes so
hot that it would melt a plastic tube.
The metal tube stays hot enough to
burn you for several minutes after
you’ve used it. And, as in the case of
soldering irons, other people (and
pets) are vulnerable, because they
won’t necessarily know that the heat
gun is hot. Most of all, make sure that
no one in your home ever makes the
mistake of using a heat gun as a hair
dryer (Figure 3-47).
This tool is just a little more hazard-
ous than it appears.

I suggest you next practice your soldering skills on a couple of practical proj-
ects. In the first one, you can add color-coded, solid-core wires to your AC
adapter, and in the second one, you can shorten the power cord for a laptop
power supply. You can use your larger soldering iron for both of these tasks,
because neither of them involves any heat-sensitive components.
Modifying an AC Adapter
In the previous chapter, I mentioned the irritation of being unable to push the
wires from your AC adapter into the holes of your breadboard. So, let’s fix this
right now:
1. Cut two pieces of solid-conductor 22-gauge wire—one of them red, the
other black or blue. Each should be about 2 inches long. Strip a quarter-
inch of insulation from both ends of each piece of wire.
2. Trim the wire from your AC adapter.You need to expose some fresh, clean
copper to maximize your chance of getting the solder to stick.
I suggest that you make one conductor longer than the other to minimize
the chance of the bare ends touching and creating a short circuit. Use
your meter, set to DC volts, if you have any doubt about which conductor
is positive.
Solder the wires and add heat-shrink tubing as you did in the practice session.
The result should look like Figure 3-51.
Figure 3-51. Solid-core color-coded wires, soldered onto the wires from an AC adapter, pro-
vide a convenient way to feed power to a breadboard. Note that the wires are of differing
lengths to reduce the risk of them touching each other.
Shortening a Power Cord
When I travel, I like to minimize everything. It always annoys me that the pow-
er cord for the power supply of my laptop is 4 feet long. The thinner wire that
connects the power supply to the computer is also 4 feet long, and I just don’t
need that much wire.
Choose the RightTubing
If you use heat-shrink tubing on 110v
AC cord, as is being done in this ex-
periment, make sure you use tubing
that’s been rated for 110v use.

Chapter 3112
After searching exhaustively I couldn’t find any laptop power cables shorter
than 3 feet, so I decided to shorten one myself. If you feel no need to do this,
you should try the following procedure on an old extension cord, just as an
exercise. You do need to go through these steps to acquire some practice in
soldering heavier, stranded wire and using heat-shrink tubing:
1. Use your wire cutters to chop the wire, and then a utility knife to split the
two conductors, with one shorter than the other. When splicing a pow-
er cord or similar cable containing two or more conductors, it’s good to
avoid having the joints opposite each other. They fit more snugly if they
are offset, and there’s less risk of a short circuit if a joint fails.
2. Strip off a minimal amount of insulation. One-eighth of an inch (3 mm) is
sufficient. The automatic wire strippers that I mentioned in the shopping
list in Chapter 1 are especially convenient, but regular wire strippers will
do the job.
3. Cut two pieces of heat-shrink tubing, each 1 inch long, big enough to slide
over the separate conductors in your cable. Cut a separate 2-inch piece of
larger tubing that will slide over the entire joint when it’s done. The steps
described so far are illustrated in Figures 3-52 through 3-58.
4. Now for the most difficult part: activating your human memory. You have
to remember to slide the tubing onto the wire before you make your sol-
der joint, because the plugs on the ends of the wires will prevent you from
adding any heat-shrink tubing later. If you’re as impatient as I am, it’s very
difficult to remember to do this every time.
Figure 3-58. Figures 3-52 through 3-58
illustrate the sequence of steps to prepare
for making a shortened power cord for a
laptop computer power supply.

5. Use your helping hand to align the first joint. Push the two pieces of wire
together so that the strands intermingle, and then squeeze them tight
between finger and thumb, so that there are no little bits sticking out. A
stray strand of wire can puncture heat-shrink tubing when the tubing is
hot and soft and is shrinking around the joint.
6. The wire that you’re joining is much heavier than the 22-gauge wire that
you worked with previously, so it will suck up more heat, and you must
touch the soldering iron to it for a longer time. Make sure that the solder
flows all the way into the joint, and check the underside after the joint
is cool. Most likely you’ll find some bare copper strands there. The joint
should become a nice solid, rounded, shiny blob. Keep the heat-shrink
tubing as far away from the joint as possible while you’re using the solder-
ing iron, so that heat from the iron doesn’t shrink the tubing prematurely,
preventing you from sliding it over the joint later.
7. When the joint has cooled, slide the heat-shrink tubing over it, and apply
the heat gun. Now repeat the process with the other conductor. Finally,
slide the larger piece of tubing over the joint. You did remember to put
the large tubing onto the wire at the beginning, didn’t you?
Figures 3-59 through 3-65 show the steps all the way through to the end.
If you have completed the soldering exercises so far, you now have sufficient
basic skills to solder your first electronic circuit. But first, I want you to verify
the vulnerability of components to heat.
Figure 3-65. Completion of the shortened
power cord for a laptop power supply.

Chapter 3114
In Chapter 1, you saw how an LED can be damaged if too much current flows
through it. The electricity caused heat, which melted the LED. Unsurprisingly,
you can just as easily melt it by applying too much heat to one of its leads with
a soldering iron. The question is: how much heat is too much? Let’s find out.
You will need:
• 30-watt or 40-watt soldering iron
• A couple of LEDs (that are expendable)
• 680Ω resistor
• Wire cutters and sharp-nosed pliers
• “Helping hand”gadget to hold your work
I don’t want you to use alligator clips to join the LED to a power supply, be-
cause the alligator clip will divert and absorb some of the heat from your sol-
dering iron. Instead, please use some sharp-nosed pliers to bend each of the
leads from an LED into little hooks, and do the same thing with the wires on a
680Ω load resistor. Finally bend the new wires on your AC adapter so that they,
too, are tiny hooks. Now you can put the hooks together like links in a chain,
as shown in Figure 3-66.
Grip the plastic body of the LED in your helping hand. Plastic is not a good
thermal conductor, so the helping hand shouldn’t siphon too much heat away
from our target. The resistor can dangle from one of the leads on the LED, and
the wire from the AC adapter can hang from that, a little farther down. Gravity
should be sufficient to make this work. Set your AC adapter to deliver 12 volts
as before, plug it in, and your LED should be shining brightly. I used a white
LED in this experiment, because it’s easier to photograph.
Make sure your two soldering irons are really hot. They should have been
plugged in for at least five minutes. Now take the pencil-style iron and hold its
tip firmly against one of the leads on your glowing LED, while you check the
time with a watch. Figure 3-67 shows the setup.
I’m betting that you can sustain this contact for a full three minutes without
burning out the LED. This is why you use a 15-watt soldering iron for delicate
electronics work—it doesn’t endanger the components.
Allow your LED wire to cool, and then apply your more powerful soldering iron
to the same piece of wire as before. Again, make sure it is completely hot, and
I think you’ll find that the LED will go dark after as little as 10 seconds (note,
some LEDs can survive higher temperatures than others).This is why you don’t
use a 30-watt soldering iron for delicate electronics work.
The large iron doesn’t necessarily reach a higher temperature than the small
one. It just has a larger heat capacity. In other words, a greater quantity of heat
can flow out of it, at a faster rate.
12V DC
Power
Supply
Figure 3-66. By literally hooking together
the leads from a resistor and a white-light
LED, we minimize pathways for heat to
escape during the subsequent test.
Figure 3-67. Applying heat with a 15-watt
soldering iron. A typical LED should
withstand this treatment for two or three
minutes, but if you substitute a 30-watt
soldering iron, the LED is likely to burn out
in under 15 seconds.

Throw away your burned-out LED. Substitute a new one, connected as before,
but add a full-size copper alligator clip to one of the leads up near the body of
the LED, as shown in Figure 3-68. Press the tip of your 30-watt or 40-watt sol-
dering iron against the lead just below the alligator clip. This time, you should
be able to hold the powerful soldering iron in place for a full two minutes
without burning out the LED.
Imagine the heat flowing out through the tip of your soldering iron, into the
wire that leads to the LED—except that the heat meets the alligator clip along
the way, as shown in Figure 3-69. The clip is like an empty vessel waiting to
be filled. It offers much less resistance to heat than the remainder of the wire
leading to the LED, so the heat prefers to flow into the copper clip, leaving the
LED unharmed. At the end of your experiment, if you touch the clip, you’ll find
that it’s hot, while the LED remains relatively cooler.
The alligator clip is known as a heat sink, and it should be made of copper,
because copper is one of the best conductors of heat.
Because the 15-watt soldering iron failed to harm the LED, you may conclude
that the 15-watt iron is completely safe, eliminating all need for a heat sink.
Well, this may be true. The problem is, you don’t really know whether some
semiconductors may be more heat-sensitive than LEDs. Because the con-
sequences of burning out a component are so exasperating, I suggest you
should play it safe and use a heat sink in these circumstances:
• If you apply 15-watt iron extremely close to a semiconductor for 20 sec-
onds or more.
• If you apply a 30-watt iron near resistors or capacitors for 10 seconds or
more. (Never use it near semiconductors.)
• If you apply a 30-watt iron near anything meltable for 20 seconds or more.
Meltable items include insulation on wires, plastic connectors, and plastic
components inside switches.
Rules for Heat Sinking
1. Full-size copper alligator clips do work better.
2. Clamp the alligator clip as close as possible to the component and as far
as possible from the joint. (You don’t want to suck too much heat away
from the joint.)
3. Make sure there is a metal-to-metal connection between the alligator clip
and the wire to promote good heat transfer.
Figure 3-68. When a copper alligator clip is
used as a heat sink, you should be able to
apply a 30-watt soldering iron (below the
clip) without damaging the LED.
Heat Flow
Soldering Iron
Heat Sink
Figure 3-69. The heat sink intercepts the
heat, sucks it up, and protects the LED
from damage.

Chapter 3116
Fundamentals
All about perforated board
For the remainder of this book, you’ll be using perforated
board whenever you want to create permanent, soldered
circuits. There are three ways to do this:
1. Point-to-point wiring. You use perforated board that
has no connections behind the holes. Either the board
has no copper traces on it at all, as in Figure 3-70, or
you will find a little circular copper circle around each
hole, as in Figure 3-71. These circles are not connected
with each other and are used only to stabilize the com-
ponents that you assemble.
Point-to-point wiring allows you to place the com-
ponents in a convenient, compact layout that can be
very similar to a schematic. Under the board you bend
the wires to link the components, and solder them
together, adding extra lengths of wire if necessary. The
advantage of this system is that it can be extremely
compact. The disadvantage is that the layout can be
confusing, leading to errors.
Figure 3-70
Figure 3-71. Either this type of perforated board or the type in Fig-
ure 3-70 can be used for point-to-point wiring in Experiment 14.
2. Breadboard-style wiring. Use perforated board that is
printed with copper traces in exactly the same pattern
as the conductors inside a breadboard. Once your
circuit works on the breadboard, you move the com-
ponents over to the perfboard one by one, maintain-
ing their exact same positions relative to each other.
You solder the“legs”of the components to the copper
traces, which complete the circuit. Then you trim off
the surplus wire. The advantage of this procedure is
that it’s quick, requires very little planning, and mini-
mizes the possibility for errors. The disadvantage is that
it tends to waste space. A cheap example is shown in
Figure 3-72.
3. You can etch your own circuit board with customized
copper traces that link your components in a point-
to-point layout. This is the most professional way to
complete a project, but it requires more time, trouble,
and equipment than is practical in this book.
Point-to-point wiring is like working with alligator clips,
on a much smaller scale. The first soldered project will
use this procedure.
Figure 3-72. Perforated board etched with copper in variants of
a breadboard layout. This example is appropriate for Experi-
ment 15.

You will need:
• Breadboard
• Plain perforated board (no copper etching necessary)
• Small vise or clamp to hold your perforated board
• Resistors, various
• Capacitors, electrolytic, 100 µF and 220 µF, one of each
• Red LED, 5 mm, rated for 2 volts approximately
• 2N6027 programmable unijunction transistor
Your first circuit using a PUT was a slow-speed oscillator that made an LED
flash about twice each second. The flashes looked very “electronic,” by which
I mean that the LED blinked on and off without a gradual transition between
each state. I’m wondering if we can modify this circuit to make the LED pulse
in a more gentle, interesting way, like the warning light on an Apple MacBook
when it’s in “sleep” mode. I’m thinking that something of this sort might be
wearable as an ornament, if it’s small enough and elegant enough.
I’m also thinking that this first soldering project will serve three purposes. It
will test and refine your skill at joining wires together, will teach you point-to-
point wiring with perfboard, and will give you some additional insight into the
way that capacitors can be used to adjust timing.
Look back at the original schematic in Experiment 11, on page 82. Refresh your
memory about the way it worked.The capacitor charges through a resistor un-
til it has enough voltage to overcome the internal resistance in the PUT. Then
the capacitor discharges through the PUT and flashes the LED.
If you drew a graph of the light coming out of the LED, it would be a thin, square-
shaped pulse, as shown in Figure 3-73. How can we fill it out to make it more like
the curve in Figure 3-74, so that the LED fades gently on and off, like a heartbeat?
One thing is obvious: the LED is going to be emitting a greater total amount of
light in each cycle. Therefore, it’s going to need more power. This means that
C1, in Figure 3-75, must be a larger capacitor.
When we have a larger capacitor, it takes longer to charge. To keep the flashes
reasonably frequent, we’ll need a lower-value resistor for R1 to charge the ca-
pacitor quickly enough. In addition, reducing the values of R2 and R3 will pro-
gram the PUT to allow a longer pulse.
Most important, I want to discharge the capacitor through a resistor to make
the onset of the pulse gradual instead of sudden. Remember, when you have
a resistor in series with a capacitor, the capacitor not only charges more slowly,
but discharges more slowly.
Time
Brightness
Figure 3-73
Time
Brightness
Figure 3-74. The original PUT oscillator
circuit in Experiment 11 made the LED
emit sharp, short flashes. The upper graph
shows what we might find if we measured
light output over time. The second graph
shows a gentler onset to each flash, fol-
lowed by a slow fade-out. Capacitors can
be used to create this effect.

Chapter 3118
Figure 3-75 shows these features. Compare it with Figure 2-103 on page 85. R1
is now 33K instead of 470K. R2 and R3 are reduced to 1K. R4 also is 1K, to so
that the capacitor takes longer to discharge through it. And C1 is now 100 µF
instead of 2.2 µF.
Assemble this circuit on a breadboard, and compare the results when you in-
clude R4 or bypass it with a plain piece of jumper wire. It softens the pulse a
bit, but we can work on it some more. On the output side of the PUT, we can
add another capacitor. This will charge itself when the pulse comes out of the
PUT, and then discharge itself gradually through another resistor, so that the
light from the LED dies away more slowly.
Figure 3-76 shows the setup. C2 is large—220 µF—so it sucks up the pulse that
comes out of the PUT, and then gradually releases it through 330Ω resistor R5
and the LED. You’ll see that the LED behaves differently now, fading out inside
of blinking off. But the resistances that I’ve added have dimmed the LED, and
to brighten it, you should increase the power supply from 6 volts to 9 volts.
Remember that a capacitor imposes a smoothing effect only if one side of it
is grounded to the negative side of the power supply. The presence of the
negative charge on that side of the capacitor attracts the positive pulse to the
other side.
I like the look of this heartbeat effect. I can imagine a piece of wearable elec-
tronic jewelry that pulses in this sensual way, very different from the hard-
edged, sharp-on-and-off of a simple oscillator circuit. The only question is
whether we can squeeze the components into a package that is small enough
to wear.
Figure 3-76. The second step toward a
gentler flashing effect is to add another
capacitor, C2, which charges quickly with
each pulse and then discharges slowly
through R5 and the LED below it.
Same components as before, plus:
R5: 330Ω
C2: 220 µF electrolytic
Power supply increased to 9 volts
R1
9V
DC
C1
C2
R2 R3
R4
R5
Q1
Figure 3-77. On a dark night in a rural area, the
heartbeat flasher may be attractive in unexpected
ways.
R1
C1
R2
Q1
R3
R4
Figure 3-75. The first step toward creating
a gentler flashing effect is to use a larger
capacitor for C1 and discharge it through
a resistor, R4. Lower-value resistors are
necessary to charge the capacitor rapidly
enough.
R1: 33K
R2: 1K
R3: 1K
R4: 1K
Q1: 2N6027

Resizing the Circuit
The first step is to look at the physical components and imagine how to fit them
intoasmallspace.Figure3-78showsa3Dviewofacompactarrangement.Check
this carefully, tracing all the paths through the circuit, and you’ll see that it’s the
same as the schematic.The trouble is that if we solder the components together
like this, they won’t have much strength. All the little wires can bend easily, and
there’s no easy way to mount the circuit in something or on something.
R4
R1
R2
R3
R5
C1
C2
Figure 3-78. This layout of components replicates their connections in the schematic
diagram while squeezing them into a minimal amount of space.
The answer is to put it on a substrate, which is one of those terms that people in
the electronics field like to use, perhaps because it sounds more technical than
“perfboard.” But perforated board is what we need, and Figure 3-79 shows the
components transferred onto a piece of board measuring just 1 inch by 0.8 inch.
The center version of this diagram uses dotted lines to show how the compo-
nents will be connected with each other underneath the board. Mostly the
leads that stick out from underneath the components will be long enough to
make these connections.
Finally, the bottom version of the perfboard diagram shows the perfboard
flipped left-to-right (notice the L and the R have been transposed to remind
you, and I’ve used a darker color to indicate the underside of the board).
Orange circles indicate where solder joints will be needed.
The LED should be unpluggable, because we may want to run it at some dis-
tance from the circuit. Likewise the power source should be unpluggable. For-
tunately we can buy miniature connectors that fit right into the perforated
board. You may have to go to large online retail suppliers such as Mouser.com
for these. Some manufacturers call them “single inline sockets and headers,”
while others call them“boardmount sockets and pinstrip headers.”Refer back
to Figure 3-29 and check the shopping list for more details.
This is a very compact design that will require careful work with your pencil-
style soldering iron. Because a piece of perforated board as small as this will
tend to skitter around, I suggest that you apply your miniature vise to one end
to anchor it with some weight while still allowing you to turn it easily.
R
L
R
L
R
L
Figure 3-79. Perforated board can be used
to support the layout of components. Their
leads are soldered together under the
board to create the circuit. The middle dia-
gram shows the wires under the board as
dashed lines. The bottom diagram shows
the board from underneath, flipped left to
right. Orange circles indicate where solder
joints will be necessary.

Chapter 3120
When I’m working on this kind of project, I like to place it (with the vise at-
tached) on a soft piece of polyurethane foam—the kind of slab that is nor-
mally used to make a chair cushion. The foam protects the components from
damage when the board is upside-down, and again helps to prevent the work
from sliding around unpredictably.
Step by Step
Here’s the specific procedure for building this circuit:
1. Cut the small piece of perfboard out of a sheet that has no copper traces
on it. You can cut the section using your miniature hobby saw, or you may
be able to snap the board along its lines of holes, if you’re careful. Alter-
natively, use a small ready-cut piece of perfboard with copper circles on it
that are not connected to one another. You’ll ignore the copper circles in
this project. (In the next experiment, you’ll deal with the additional chal-
lenge of making connections between components and copper traces on
perforated board.)
2. Gather all the components and carefully insert them through holes in the
board, counting the holes to make sure everything is in the right place.
Flip the board over and bend the wires from the components to anchor
them to the board and create connections as shown. If any of the wires
isn’t long enough, you’ll have to supplement it with an extra piece of
22-gauge wire from your supply.You can remove all the insulation, as we’ll
be mounting the perfboard on a piece of insulating plastic.
3. Trim the wires approximately with your wire cutters.
4. Make the joints with your pencil soldering iron. Note that in this circuit,
you are just joining wires to each other. The components are so close to-
gether that they’ll prevent each other from wiggling around too much. If
you are using board with copper pads (as I did), and some solder connects
with them, that’s OK—as long as it doesn’t creep across to the neighbor-
ing component and create a short circuit.
5. Check each joint using a close-up magnifying glass, and wiggle it with
pointed-nosed pliers. If there isn’t enough solder for a really secure joint,
reheat it and add more. If solder has created a connection that shouldn’t
be there, use a utility knife to make two parallel cuts in the solder, and
scrape away the little section between them.
Generally, I insert three or four components, trim the wires approximately, sol-
der them, trim their wires finally, then pause to check the joints and the place-
ment. If I solder too many components in succession, there’s a greater risk of
missing a bad joint, and if I make an error in placing a component, undoing
it will be much more problematic if I have already added a whole lot more
components around it.
Figures 3-80 and 3-81 show the version of this project that I constructed, be-
fore I trimmed the board to the minimum size.
Figure 3-80. Components mounted on a
piece of perforated board.
Figure 3-81. The assembly seen from
below. The copper circles around the holes
are not necessary for this project. Some of
them have picked up some solder, but this
is irrelevant as long as no unintentional
short circuits are created.

FlyingWire Segments
The jaws of your wire cutters exert a powerful force that peaks and then is suddenly
released when they cut through wire. This force can be translated into sudden mo-
tion of the snipped wire segment. Some wires are relatively soft, and don’t pose a
risk, but harder wires can fly in unpredictable directions at high speed, and may hit
you in the eye. The leads of transistors are especially hazardous in this respect.
I think it’s a good idea to wear safety glasses when trimming wires.
Finishing the Job
I always use bright illumination. This is not a luxury; it is a necessity. Buy a
cheap desk lamp if you don’t already have one. I use a daylight-spectrum fluo-
rescent desk lamp, because it helps me identify the colored bands on resistors
more reliably. Note that this type of fluorescent lamp emits quite a lot of ultra-
violet light, which is not good for the lens in your eye. Avoid looking closely
and directly at the tube in the lamp, and if you wear glasses, they will provide
additional protection.
No matter how good your close-up vision is, you need to examine each joint
with that close-up magnifier. You’ll be surprised how imperfect some of them
are. Hold the magnifier as close as possible to your eye, then pick up the thing
that you want to examine and bring it closer until it comes into focus.
Finally, you should end up with a working circuit.You can insert the wires from
your power supply into two of the tiny power sockets, and plug a red LED into
the remaining two sockets. Remember that the two center sockets are nega-
tive, and the two outer sockets are positive, because it was easier to wire the
circuit this way. You should color-code them to avoid mistakes.
So now you have a tiny circuit that pulses like a heartbeat. Or does it? If you
have difficulty making it work, retrace every connection and compare it with the
schematic. If you don’t find an error, apply power to the circuit, attach the black
lead from your meter to the negative side, and then go around the circuit with
the red lead, checking the presence of voltage. Every part of this circuit should
show at least some voltage while it’s working. If you find a dead connection,
you may have made a bad solder joint, or missed one entirely.
When you’re done, now what? Well, now you can stop being an electronics
hobbyist and become a crafts hobbyist.You can try to figure out a way to make
this thing wearable.
First you have to consider the power supply. Because of the components that I
used, we really need 9 volts to make this work well. How are you going to make
this 9-volt circuit wearable, with a bulky 9-volt battery?
I can think of three answers:

Chapter 3122
1. You can put the battery in a pocket, and mount the flasher on the outside
of the pocket, with a thin wire penetrating the fabric. Note that the tiny
power connector on the perforated board will accept two 22-gauge wires
if they are solid core, or if they are stranded (like the wires from a 9-volt
battery connector) but have been thinly coated with solder.
2. You could mount the battery inside the crown of a baseball cap, with the
flasher on the front.
3. You can put together three 3-volt button batteries in a stack, held in some
kind of plastic clip. If you try this option, it may not be a good idea to try
to solder wire to a battery. You will heat the liquid stuff inside the battery,
which may not be good for it, and may not be good for you if the liquid
starts boiling and the battery bursts open. Also, solder doesn’t stick easily
to the metallic finish on most battery terminals.
Most LEDs create a sharply defined beam of light, which you may want to dif-
fuse to make it look nicer. One way to do this is to use a piece of transparent
acrylic plastic, at least 1/4 inch thick, as shown in Figure 3-82. Sandpaper the
front of the acrylic, ideally using an orbital sander that won’t make an obvious
pattern. Sanding will make the acrylic translucent rather than transparent.
Drill a hole slightly larger than the LED in the back of the acrylic. Don’t drill all
the way through the plastic. Remove all fragments and dust from the hole by
blasting some compressed air into it, or by washing it if you don’t have an air
compressor. After the cavity is completely dry, get some transparent silicone
caulking or mix some clear five-minute epoxy and put a drop in the bottom of
the hole. Then insert the LED, pushing it in so that it forces the epoxy to ooze
around it, making a tight seal. See Figure 3-82.
Figure 3-82. This cross-sectional view shows a sheet of transparent acrylic in which a hole
has been drilled part of the way from the back toward the front. Because a drill bit creates
a hole with a conical shape at the bottom, and because the LED has rounded contours,
transparent epoxy or silicone caulking can be injected into the hole before mounting the
LED.
Try illuminating the LED, and sand the acrylic some more if necessary. Finally,
you can decide whether to mount the circuit on the back of the acrylic, or
whether you want to run a wire to it elsewhere.

Because the LED will flash at about the speed of a human heart while the per-
son is resting, it may look as if it’s measuring your pulse, especially if you mount
it on the center of your chest or in a strap around your wrist. If you enjoy hoax-
ing people, you can suggest that you’re in such amazingly good shape, your
pulse rate remains constant even when you’re taking strenuous exercises.
To make a good-looking enclosure for the circuit, I can think of options rang-
ing from embedding the whole thing in clear epoxy to finding aVictorian-style
locket. I’ll leave you to consider alternatives, because this is a book about elec-
tronics rather than handicrafts.
However, I will address one final issue: how long will this gadget continue
flashing?
If you check the following section“Essentials: Battery life,”you’ll find that a reg-
ular alkaline 9-volt battery should keep the LED flashing for about 50 hours.
ESSENTIALS
Battery life
Any time you finish a circuit that you intend to run from a battery, you’ll want
to calculate the likely battery life. This is easily done, because manufacturers
rate their batteries according to the“ampere hours”they can deliver. Keep the
following in mind:
• The abbreviation for amp-hours is Ah, sometimes printed as AH. Milliampere-
hours are abbreviated mAh.
• The rating of a battery in amp-hours is equal to the current, in amps, multi-
plied by the number of hours that the battery can deliver it.
Thus, in theory 1 amp-hour can mean 1 amp for 1 hour, or 0.1 amp for 10 hours,
or 0.01 amp for 100 hours—and so on. In reality, it’s not as simple as this, be-
cause the chemicals inside a battery become depleted more quickly when you
draw a heavy current, especially if the battery gets hot. You have to stay within
limits that are appropriate to the size of the battery.
For instance, if a small battery is rated for 0.5 amp-hours, you can’t expect to
draw 30 amperes from it for 1 minute. But you should be able to get 0.005 amps
(i.e., 5 milliamps) for 100 hours without any trouble. Remember, though, that
the voltage delivered by a battery will be greater than its rated voltage when
the battery is fresh, and will diminish below its rated voltage while the battery is
delivering power.
According to some test data that I trust (I think they are a little more realistic
than the estimates supplied by battery manufacturers), here are some numbers
for typical batteries:
• Typical 9 volt alkaline battery: 0.3 amp-hours, while delivering 100 mA.
• Typical AA size, 1.5-volt alkaline battery: 2.2 amp-hours, while delivering
100 mA.
• Rechargeable nickel-metal hydride battery: about twice the endurance of a
comparably sized alkaline battery.
• Lithium battery: maybe three times the endurance of an alkaline battery.

Chapter 3124
Background
Maddened by measurement
Throughout most of this book, I’ve mostly used measurements in inches,
although sometimes I’ve digressed into the metric system, as when referring to
“5-mm LEDs.”This isn’t inconsistency on my part; it reflects the conflicted state
of the electronics industry, where you’ll find inches and millimeters both in daily
use, often in the very same data sheet.
The United States is the only major nation still using the old system of units
that originated in England. (The other two holdouts are Liberia and Myanmar,
according to the CIA’s World Factbook.) Still, the United States has led many
advances in electronics, especially the development of silicon chips, which have
contacts spaced 1/10 inch apart. These standards became firmly established,
and show no sign of disappearing.
To complicate matters further, even in the United States, you can encounter two
incompatible systems for expressing fractions of an inch. Drill bits, for instance,
are measured in multiples of 1/64 inch, while metal thicknesses may be mea-
sured in decimals such as 0.06 inch (which is approximately 1/16 inch).
The metric system is not necessarily more rational than the U.S. system. Origi-
nally, when the metric system was formally introduced in 1875, the meter was
defined as being 1/10,000,000 of the distance between the North Pole and the
equator, along a line passing through Paris—a quixotic, Francocentric conceit.
Since then, the meter has been redefined three times, in a series of efforts to
achieve greater accuracy in scientific applications.
As for the usefulness of a 10-based system, moving a decimal point is certainly
simpler than doing calculations in 64ths of an inch, but the only reason we
count in tens is because we happen to have evolved with that number of digits
on our hands. A 12-based system would really be more convenient, as numbers
would be evenly divisible by 2 and 3.
As we’re stuck with the whimsical aspects of length measurement, I’ve created
the charts in Figures 3-83 and 3-84 to assist you in going from one system to
another. From these you will see that when you need to drill a hole for a 5 mm
LED, a 3/16-inch drill bit is about right. (In fact, it results in a better, tighter fit
than if you drill an actual 5 mm hole.)

Figure 3-83. Because units of measurement are not standardized in electronics, conversion is often necessary. The chart on the right is a
5x magnification of the bottom section of the chart on the left.

Chapter 3126
Figure 3-84. This chart allows conversion between hundredths of an inch, conventional U. S. fractions of an inch, and fractions expressed
in thousandths of an inch.

Time now to add some of the enhancements to the intrusion alarm that I dis-
cussed at the end of Experiment 11. I’m going to show you how the alarm
can be triggered if you install various detectors on windows and doors in your
home. I’ll also show how the alarm can be wired so that it locks itself on and
continues to make noise even after a door or window is reclosed.
This experiment will demonstrate the procedure for transferring a project from
a breadboard to a piece of perforated board that has copper connections laid
out identically to the ones inside the breadboard, as shown earlier in Figure
3-72. And you’ll mount the finished circuit in a project box with switches and
connectors on the front.
When all is said and done, you’ll be ready for wholesale circuit building. The
explanations in the rest of this book will get gradually briefer, and the pace
will increase.
You will need:
• Perforated board etched with copper in a breadboard layout
• Small vise or clamp to hold your perforated board
• The same components that you used in Experiment 11, plus:
-- 2N2222 NPN transistor. Quantity: 1.
-- DPDT relay. Quantity: 1.
-- SPDT toggle switch. Quantity: 1.
-- 1N4001 diode. Quantity: 1.
-- Red and green 5mm LEDs. Quantity: 1 each.
-- Project box, 6 × 3 × 2 inches.
-- Power jack, type N, and matching power socket, type N.
-- Binding posts.
-- Stranded 22-gauge wire, three different colors.
-- Magnetic sensor switches, sufficient for your home.
-- Alarm network wiring, sufficient for your home.

Chapter 3128
Magnetic Sensor Switches
A typical alarm sensor switch consists of two modules: the magnetic mod-
ule and the switch module, as shown in Figures 3-85 and 3-86. The magnetic
module contains a permanent magnet, and nothing else. The switch module
contains a“reed switch,”which makes or breaks a connection (like a contact in-
side a relay) under the influence of the magnet. When you bring the magnetic
module close to the switch module, you may faintly hear the reed switch click
as it flips from one state to the other.
Like all switches, reed switches can be normally open or normally closed. For
this project, you want the kind of switch that is normally open, and closes
when the magnetic module is close to it.
Attach the magnetic module to the moving part of a door or window, and at-
tach the switch module to the window frame or door frame.When the window
or door is closed, the magnetic module is almost touching the switch module.
The magnet keeps the switch closed until the door or window is opened, at
which point the switch opens.
The only question is: how do we use this component to trigger our alarm? As
long as a small current flows through all our magnetic sensor switches, the
alarm should be off, but if the flow of current stops, the alarm should switch on.
We could use a relay that is“always on”while the alarm is armed. When the cir-
cuit is interrupted, the relay relaxes and its other pair of contacts closes, which
could power up the alarm noisemaker.
But I don’t like this idea. Relays take significant power, and they can get hot.
Most of them are not designed to be kept“always-on.”I’d prefer to handle the
task using a transistor.
S
S
S
N
N
N
Figure 3-86. This cutaway diagram shows a reed switch (bottom) and the magnet that
activates it (top), inside an alarm sensor. The switch contains two flexible magnetized
strips, the upper one with its south pole adjacent to an electrical contact, the lower one
with its north pole adjacent to an electrical contact. When the south pole of the magnet
approaches the switch, the magnetic force (shown as dashed lines) repels the south
contact and attracts the north contact, causing them to snap together. Two screws on the
outside of the casing are connected with the strips inside.
Figure 3-85. In this simple alarm sensor
switch, the lower module contains a mag-
net, which opens and closes a reed switch
sealed into the upper module.

A Break-to-Make Transistor Circuit
First, recall how an NPN transistor works.When the base is not sufficiently posi-
tive, the transistor blocks current between its collector and emitter, but when
the base is relatively positive, the transistor passes current.
Take a look at the schematic in Figure 3-87, which is built around our old friend
the 2N2222 NPN transistor. When the switch is closed, it connects the base of
the transistor to the negative side of the power supply through a 1K resistor.
At the same time, the base is connected with the positive side of the power
supply through a 10K resistor. Because of the difference in resistances and the
relatively high turn-on voltage for the LED, the base is forced below its turn-on
threshold, and as a result, the transistor will not pass much current. The LED
will glow dimly at best.
Now what happens when the switch is opened? The base of the transistor
loses its negative power supply and has only its positive power supply. It be-
comes much more positive, above the turn-on threshold for the transistor,
which tells the transistor to lower its resistance and pass more current.The LED
now glows brightly. Thus, when the switch is turned off and breaks the con-
nection, the LED is turned on.
This seems to be what we want. Imagine a whole series of switches instead
of just one switch, as shown in Figure 3-88. The circuit will still work the same
way, even if the switches are scattered all over your home, because the resis-
tance in the wires connecting the switches will be trivial compared with the
resistance of the 1K resistor.
12V
DC
680
Q1
1K
10K
Switches
activated
by opened
doors or
windows
Figure 3-88. A network of switches, wired in series, can be substituted for the single switch
in Figure 3-87. Now any one switch will break continuity and trigger the transistor.
12V
DC
680
Q1
1K
10K
Figure 3-87. In this demonstration circuit,
when the switch is opened, it interrupts
negative voltage to the base of the transis-
tor, causing the transistor to lower its
resistance, allowing current to reach the
LED. Thus, when the switch is turned off, it
turns on the LED.

Chapter 3130
I have shown the switches open, because that’s the way the schematic for a
switch is drawn, but imagine them all closed. The base of the transistor will
now be supplied through the long piece of wire connecting all the closed
switches, and the LED will stay dark. Now if just one switch is opened, or if
anyone tampers with the wire linking them, the base of the transistor loses its
connection to negative power, at which point the transistor conducts power
and the LED lights up.
While all the switches remain closed, the circuit is drawing very little current—
probably about 1.1 mA. So you could run it from a typical 12-volt alarm battery.
Now suppose we swap out the LED and put a relay in there instead, as shown
in Figure 3-89. I don’t mind using a relay in this location, because the relay will
not be “always on.” It will normally be off, and will draw power only when the
alarm is triggered.
12V
DC
Q1
R1
1K
10K
Switches
activated
by opened
doors or
windows
Figure 3-89. If the LED and 680Ω resistor shown in are removed, and a relay takes their
place, the relay will be activated when any switch in the sensor network is opened.
Try one of the 12-volt relays that you used previously. You should find that
when you open the switch, the relay is energized. When you close the switch,
the relay goes back to sleep. Note that I eliminated the 680Ω resistor from the
circuit, because the relay doesn’t need any protection from the 12-volt power
supply.

Self-Locking Relay
There’s only one remaining problem: we want the alarm to continue making
noise even after someone who has opened a door or window closes it again
quickly. In other words, when the relay is activated, it must lock itself on.
One way to do this would be by using a latching relay.The only problem is that
we would then need another piece of circuitry to unlatch it. I prefer to show
you how you can make any relay keep itself switched on after it has received
just one jolt of power. This idea will be useful to you later in the book as well.
The secret is to supply power to the relay coil through the two contacts inside
the relay that are normally open. (Note that this is exactly opposite to the relay
oscillator, which supplied power to its coil through the contacts that were nor-
mally closed. That setup caused the relay to switch itself off almost as soon as
it switched itself on. This setup causes the relay to keep itself switched on, as
soon as it has been activated.)
In Figure 3-90, the four schematics illustrate this. You can imagine them as be-
ing like frames in a movie, photographed microseconds apart. In the first pic-
ture, the switch is open, the relay is not energized, and nothing is happening.
In the second, the switch has been closed to energize the coil. In the third, the
coil has pulled the contact inside the relay, so that power now reaches the coil
via two paths. In the fourth, the switch has been opened, but the relay is still
powering its own coil through its contacts. It will remain locked in this state
until the power is disconnected.
12V
DC
12V
DC
12V
DC
12V
DC
A
Figure 3-90. This sequence of schematics shows the events that occur when a relay is
energized. Initially, the switch is open. Then the switch is closed, activating the relay. The
relay then powers itself through its own internal contacts. The relay remains energized
even after the switch is opened again. Power switched by the relay can be taken from the
circuit at point A.
All we need to do, to make use of this idea, is to substitute the transistor for the
on/off switch, and tap into the circuit at point A, running a wire from there to
the noisemaking module.
Figure 3-91 shows how that would work. When the transistor is activated by
any of the network of sensor switches, as previously explained, the transistor
conducts power to the relay. The relay locks itself on, and the transistor be-
comes irrelevant.

Chapter 3132
Q1
R1
1K
10K
Power to
noise
maker
12V
DC
Switches
activated
by opened
doors or
windows
Figure 3-91. The self-locking relay depicted in has been incorporated in the alarm circuit,
so that if any switch in the network is opened, the relay will continue to power the noise
maker even if the switch is closed again.
Because I’ve been adding pieces to the original alarm noisemaker circuit, I’ve
updated the block diagram from Figure 2-112 to show that we can still break
this down into modules with simple functions. The revised diagram is shown
in Figure 3-92.
Blocking Bad Voltage
One little problem remains: in the new version of the circuit, if the transistor
goes off while the relay is still on, current from the relay can flow back up the
wire to the emitter of the transistor, where it will try to flow backward through
the transistor to the base, which is “more negative,” as it is linked through all
the magnetic switches and the 1K resistor to the negative side of the power
supply.
Applying power backward through a transistor is not a nice thing to do.There-
fore the final schematic in this series shows one more component, which you
have not seen before: a diode, labeled D1. See Figure 3-93.The diode looks like
the heart of an LED, and indeed, that’s pretty much what it is, although some
diodes are much more robust. It allows electricity to flow in only one direction,
Slow Oscillator
Fast Oscillator
Amplifier
Loudspeaker
Power
Mag. Switches
Locking Relay
Figure 3-92. This block diagram previously
shown in Figure 2-112 on page 90 has been
updated to include the magnetic-switch
network and locking-relay control system.

from positive to negative, as shown by its arrow symbol. If current tries to flow
in the opposite direction, the diode blocks it. The only price you pay for this
service is that the diode imposes a small voltage drop on electricity flowing in
the“OK”direction.
So now, positive flow can pass from the transistor, through the diode, to the
relay coil, to get things started. The relay then supplies itself with power, but
the diode prevents the positive voltage from getting back into the transistor
the wrong way.
Perhaps a more elegant solution to the problem is to connect the NO leg of
the relay via a 10k resistor to the base connection. When the relay is not ener-
gized, the NO leg is inert and simply behaves as a parasitic capacitance on the
node. When the relay becomes energized, the NO leg shunts +12V through
the common terminal via a 10k resistor into the base of the transistor. In this
circuit configuration, the transistor is never exposed to a potentially harmful
voltage and you are not depending on leakage currents of non-ideal elements
to protect devices.
However, I needed an opportunity to introduce you to the concept of diodes.
You can check the following section “Essentials: All about diodes” to learn
more.
Q1
D1
R1
1K
10K
Power to
noise
maker
12V
DC
Switches
activated
by opened
doors or
windows
Figure 3-93. Diode D1 has been added to protect the emitter of Q1 from positive voltage
when the relay is energized.

Chapter 3134
Essentials
All about diodes
A diode is a very early type of semiconductor. It allows electricity to flow in one
direction, but blocks it in the opposite direction. (A light-emitting diode is a
much more recent invention.) Like an LED, a diode can be damaged by revers-
ing the voltage and applying excessive power, but most diodes generally have
a much greater tolerance for this than LEDs. The end of the diode that blocks
positive voltage is always marked, usually with a circular band, while the other
end remains unmarked. Diodes are especially useful in logic circuits, and can
also convert alternating current (AC) into direct current (DC).
A Zener diode is a special type that we won’t be using in this book. It blocks cur-
rent completely in one direction, and also blocks it in the other direction until a
threshold voltage is reached—much like a PUT.
Signal diodes are available for various different voltages and wattages. The
1N4001 diode that I recommend for the alarm activation circuit is capable of
handling a much greater load at a much higher voltage, but I used it because it
has a low internal resistance. I wanted the diode to impose a minimal voltage
drop, so that the relay would receive as much voltage as possible.
It’s good practice to use diodes at less than their rated capacity. Like any semi-
conductor, they can overheat and burn out if they are subjected to mistreatment.
The schematic symbol for a diode has only one significant variant: sometimes
the triangle is outlined instead of filled solid black (see Figure 3-94).
Figure 3-94. Either of these schematic symbols may be used to represent a diode,
but the one on the right is more common than the one on the left.

Completing the Breadboard Alarm Circuit
It’s time now to breadboard the control circuit for your alarm noisemaker. Fig-
ure 3-95 shows how this can be done. I am assuming that you still have the
noisemaker, which functions as before. I’m assuming that you still have its rel-
evant components mounted on the top half of the breadboard. To save space,
I’m just going to show the additional components mounted on the bottom
half of the same breadboard.
It’s important to remember that you are not supplying power directly to the
left and right “rails” on the breadboard anymore; you are supplying power to
the relay-transistor section, and when the relay closes its contacts, the relay
supplies power to the rails.These then feed the power up to the top half of the
breadboard. So disconnect your power supply from the breadboard rails and
reconnect it as shown in Figure 3-95.
R2
R1
S1
Q1
D1
To
sensor
switches
Power to noisemaker circuit in upper part of breadboard
Figure 3-95. The schematic that was developed in the previous pages can be emulated
with components on a breadboard, as shown here. S1 is a DPDT relay. Wires to the sensor
switch network and to the power supply must be added where shown.
Because it’s a double-pole relay, I am using it to switch negative as well as
positive. This means that when the relay contacts are open, the noisemaking
section of the circuit is completely isolated from the rest of the world.

Chapter 3136
The breadboarded relay circuit is exactly the same as the schematic in Figure
3-93. The components have just been rearranged and squeezed together so
that they will fit alongside the relay. Two wires at the lower-left corner go to
the network of magnetic sensor switches that will trip the alarm; for testing
purposes, you can just hold the stripped ends of these two wires together to
simulate all the switches being closed, and separate the wires to simulate a
switch opening.
Two more wires bring power to the breadboard on either side of the relay.This
is where you should connect your power supply during testing. The output
from the relay, through its top pair of contacts, is connected with the rails of
the breadboard by a little jumper wire at top left, and another at top right.
Don’t forget to include them! One more little wire at the lower-left corner (eas-
ily overlooked) connects the lefthand side rail to the lefthand coil terminal of
the relay, so that when the relay is powering the noisemaker circuit, it powers
itself as well.
When you mount the diode, remember that the end of it that is marked with a
band around it is the end that blocks positive current. In this circuit, that’s the
lower end of the diode.
Try it to make sure that it works. Short the sensor wires together and then ap-
ply power. The alarm should remain silent. You can use your meter to check
that no voltage exists between the side rails. Now separate the sensor wires,
and the relay should click, supplying power to the side rails, which activates
the noisemaker. Even if you bring the sensor wires back together, the relay
should remain locked on. The only way to unlock it is to disconnect the power
supply.
When the circuit is active, the transistor followed by the diode drops the volt-
age slightly, but the 12-volt relay should still work.
In my test circuit, trying three different relays, they drew between 27 and 40
milliamps at 9.6 volts. Some current still leaked through the transistor when it
was in its“off”mode, but only a couple of milliamps at 0.5 volts. This low volt-
age was far below the threshold required to trip the relay.
Ready for Perfboarding
If the circuit works, the next step is to immortalize it on perforated board.
Use the type of board that has a breadboard contact pattern etched on it
in copper, as shown in Figure 3-72 on page 116. Check the following section,
“Essentials: Perfboard procedure,” for guidance on the best way to make this
particular kind of solder joint—and the subsequent section for the most com-
mon problems.

Essentials
Perfboard soldering procedure
Carefully note the position of a component on your bread-
board, and then move it to the same relative position on the
perfboard, poking its wires through the little holes.
Turn the perfboard upside down, make sure that it’s stable,
and examine the hole where the wire is poking through, as
shown in Figure 3-96. A copper trace surrounds this hole
and links it with others. Your task is to melt solder so that
it sticks to the copper and also to the wire, forming a solid,
reliable connection between the two of them.
Take your pencil-style soldering iron in one hand and some
solder in your other hand. Hold the tip of the iron against
the wire and the copper, and feed some thin solder to their
intersection. After two to four seconds, the solder should
start flowing.
Figure 3-96 Figure 3-97
Figure 3-98. To establish a connection between a section of wire
and a copper trace on perforated board, the wire is pushed
through the hole, and solder (shown in pure white for illustra-
tive purposes) completes the connection. The wire can then be
snipped short.
Allow enough solder to form a rounded bump sealing the
wire and the copper, as shown in Figure 3-97. Wait for the
solder to harden thoroughly, and then grab the wire with
pointed-nosed pliers and wiggle it to make sure you have
a strong connection. If all is well, snip the protruding wire
with your cutters. See Figure 3-98.
Because solder joints are difficult to photograph, I’m using
drawings to show the wire before and after making a rea-
sonably good joint, which is shown in pure white, outlined
with a black line.
Actual soldered perfboard is shown in the photographs in
Figure 3-99. This photograph was taken during the process
of transferring components from breadboard to perforated
board. Two or three components at a time are inserted from
the other side of the board, and their leads are bent over to
prevent them from falling out.
Figure 3-100. After soldering, the leads are snipped short and
the joints are inspected under a magnifying glass. Another two
or three components can now be inserted, and the process can
be repeated.

Chapter 3138
Tools
Four most common perfboarding errors
1. Too much solder
Before you know it, solder creeps across the board,
touches the next copper trace, and sticks to it, as de-
picted in Figure 3-101. When this happens, you have to
wait for it to cool, and then cut it with a utility knife. You
can also try to remove it with a rubber bulb and solder
wick, but some of it will tend to remain.
Even a microscopic trace of solder is enough to create
a short circuit. Check the wiring under a magnifying
glass while turning the perfboard so that the light
strikes it from different angles (or use your solder wick
to suck it away).
Figure 3-101. If too much solder is used, it makes a mess and
can create an unwanted connection with another conductor.
2. Not enough solder
If the joint is thin, the wire can break free from the
solder as it cools. Even a microscopic crack is sufficient
to stop the circuit from working. In extreme cases, the
solder sticks to the wire, and sticks to the copper trace
around the wire, yet doesn’t make a solid bridge con-
necting the two, leaving the wire encircled by solder
yet untouched by it, as shown in Figure 3-102. You
may find this undetectable unless you observe it with
magnification.
You can add more solder to any joint that may have
insufficient solder, but be sure to reheat the joint
thoroughly.
Figure 3-102. Too little solder (or insufficient heat) can allow
a soldered wire to remain separate from the soldered copper
on the perforated board. Even a hair-thin gap is sufficient to
prevent an electrical connection.
3. Components incorrectly placed
It’s very easy to put a component one hole away from
the position where it should be. It’s also easy to forget
to make a connection.
I suggest that you print a copy of the schematic, and
each time you make a connection on the perforated
board, you eliminate that wire on your hardcopy, using
a highlighter.
4. Debris
When you’re trimming wires, the little fragments that
you cut don’t disappear. They start to clutter your work
area, and one of them can easily get trapped under
your perforated board, creating an electrical connec-
tion where you don’t want it.
This is another reason for working with something soft,
such as polyurethane foam, under your project. It tends
to absorb or hold little pieces of debris, reducing the
risk of you picking them up in your wiring.
Clean the underside of your board with an old (dry)
toothbrush before you apply power to it, and keep your
work area as neat as possible. The more meticulous you
are, the fewer problems you’ll have later.
Once again, be sure to check every joint with a magni-
fying glass.

Transferring components from the breadboard to the perforated board should
be fairly simple, as long as you don’t try to move too many at once. Follow the
suggestions described in previous section “Essentials: Perfboard procedure,”
and pause frequently to check your connections. Impatience is almost always
the cause of errors in this kind of work.
Figure 3-103 shows the noisemaker section of the circuit on perfboard, with
the components positioned to minimize wasted space. Figure 3-104 shows
the perfboard with the relay and its associated components added. The two
black wires will go to the loudspeaker, the black-and-red pair of wires will
bring power to the board, and the green wires will go to the magnetic sensor
switches. Each wire penetrates the board, and its stripped end is soldered to
the copper beneath.
Test it now, in the same way that you tested the same circuit on the bread-
board. If it doesn’t work, check the following section, “Essentials: Real-world
fault tracing.” If it does work, you’re ready to trim the board and mount it in a
project box.
Essentials
Real-world fault tracing
Here’s a real-life description of the procedure for tracing a fault.
After I assembled the perfboard version of the combined noisemaker and relay
circuit, I checked my work, applied power—and although the relay clicked, no
sound came out of the loudspeaker. Of course, everything had worked fine on
the breadboard.
First I looked at component placement, because this is the easiest thing to
verify. I found no errors. Then I flexed the board gently while applying power—
and the loudspeaker made a brief“beep.”Any time this happens, you can be
virtually certain that a solder joint has a tiny crack in it.
The next step was to anchor the black lead of my meter to the negative side
of the power supply, and then switch on the power and go through the circuit
point by point, from top to bottom, checking the voltage at each point with the
red lead of the meter. In a simple circuit like this, every part should show at least
some voltage.
But when I got to the second 2N2222 transistor, which powers the loudspeaker,
its output was completely dead. Either I had melted the transistor while solder-
ing it (unlikely), or there was a bad joint. I checked the perfboard beneath the
transistor with the magnifying glass, and found that solder had flowed around
one of the leads of the transistor without actually sticking to it. The gap must
have been less than one-thousandth of an inch, but still, that was enough.
Probably, the problem had been caused by dirt or grease.
This is the kind of patient inquiry you need to follow when a circuit doesn’t
work. Check whether your components are placed correctly, check your power
supply, check the power on the board, check the voltage at each stage, and if
you are persistent, you’ll find the fault.
Figure 3-103. The noisemaker circuit has
been transplanted from breadboard to
perforated board, with no additions or
changes.
Figure 3-104. The relay-transistor control
circuit has been added. Wires to external
devices have been stripped and poked
into the perforated board, where they are
soldered in place. The green wires connect
with the sensor network, the black wires
go to the loudspeaker, and the red-and-
black wires supply power.

Chapter 3140
Switches and Inputs for the Alarm
Now you need to make the system easy to use. The block diagram in Figure
3-105 shows one additional box near the top of the sequence: User Controls.
These will consist of switches, LEDs, and connections to the outside world. To
plan this part of the job, first I have to summarize the way in which our alarm
system works at this point in its evolution.
A full-featured home alarm system normally has two modes: in-home and
away-from-home:
• Using the in-home mode, you switch on the alarm while you are at home
so that it will alert you if an intruder opens a door or window.
• Using the away-from-home mode, typically you enter a code number, af-
ter which you have 30 seconds to leave and close the door behind you.
When you return, you trigger the alarm by opening the door, but now you
have 30 seconds to go to the control panel and enter your code number
again to stop the alarm from sounding.
So far, the alarm system that you’ve been building has only an in-home mode.
Still, many people find this function useful and reassuring. Later in the book I’ll
suggest a way in which you can modify it to incorporate an away-from-home
mode, but for now, making it practical for in-home use is enough of a challenge.
Consider how it should be used on an everyday basis. It should have an on/
off switch, naturally. When it’s on, any of the magnetic sensor switches should
trigger the alarm. But what if you switch it on without realizing that you’ve left
a window open? At that time it won’t be appropriate for the alarm to sound.
What you really need is a circuit-test feature, to tell you if all the doors and
windows are closed. Then you can switch on the alarm.
I think a pushbutton would be useful to test the alarm circuit.When you press it,
a green LED should light up to indicate that the circuit is good. After you see the
green light, you let go of the pushbutton and turn on the power switch, which
illuminates a red LED, to remind you that the alarm is now armed and ready.
One additional feature would be useful: an alarm noisemaker test feature, so
that you can be sure that the system is capable of sounding its alert when
required to do so.
The circuit shown in Figure 3-106 incorporates all of these features. S1 is a
SPDT switch; S2 is a DPDT momentary pushbutton of ON-(ON) type. The sche-
matic shows it in its“relaxed”mode, when the button is not being pressed.
D1 is a red LED, D2 is a green LED, J1 is a power input jack (to be connected
with an external 12-volt supply), and R1 is a 680Ω resistor to protect the LEDs.
Note that J1 follows the usual practice of supplying positive voltage in its cen-
ter contact, and negative in the circular shell around the center.
Slow Oscillator
Fast Oscillator
Amplifier
Loudspeaker
Power
User Controls
Mag. Switches
Locking Relay
Figure 3-105. The final block diagram for
this phase of the project shows where user
controls fit in the series of functions.

When S1 is in its Off position, it still supplies positive power through its up-
per contact to S2, the pushbutton. When the pushbutton is pressed, so that it
goes into its“Test”position, the pole of S2 connects with the power and sends
it out through the sensor switches on doors and windows. The wires to these
switches will be attached via a couple of binding posts, shown here as two
circles. If the sensor switches are all closed, power returns through the second
binding post, passes through the lower set of contacts in S2, and lights D2, the
green LED. Because S1 is not supplying power to the alarm circuit board, the
alarm does not sound at this time.
To/From
Sensor
Switches
12V DC
Power
Supply
D1
D2
Red Black
To Circuit
Board
Relay
Section
(green
wires)
To Circuit Board Power Input
R1
J1
S1
S2
On
Off
Test
Ready
Figure 3-106. This schematic suggests a convenient way to add an on/off switch, a conti-
nuity testing feature, and a noisemaker testing feature to the alarm.
Now if S1 is turned to its On position, it sends power to the components on
the perforated board. The transistor circuit sends power out along the green
wires to S2, and as long as the button is not being pressed, the power goes out
through the switch network and back through S2, to the transistor, keeping its
base relatively negative. So the alarm remains silent. But as soon as a sensor
switch is opened, the circuit is broken and the alarm sounds. The only way to
stop it will be by switching S1 into its Off position.
Finally, if you press S2, the pushbutton, while S1 is in its On mode, you inter-
rupt the network of switches and activate the noisemaker. In this way, S2 does
dual duty: when S1 is off, pushbutton S2 tests the sensor switches for continu-
ity. When S1 is on, S2 tests the noisemaker to make sure it creates a noise. I
think this is the simplest possible way to implement these features.

Chapter 3142
Installing the Switches
If you bought a project box from RadioShack, it may have come with two op-
tional top panels: one made of metal, the other made of plastic. I’ll assume that
you’ll use the plastic one, as you’ll have more trouble drilling holes in metal.
The type of plastic used by RadioShack is ABS, which is very easy to shape with
the tools that I have recommended.
You have to choose a layout for the switches and other components that will
share the top panel of the project box. I like a layout to be neat, so I take the
trouble to draw it using illustration software, but a full-size pencil sketch is
almost as good. Just make sure there’s room for the components to fit to-
gether, and try to place them similarly to the schematic, to minimize the risk
of confusion.
Tape your sketch to the inside of the top panel, as shown in Figure 3-107, and
then use a sharp pointed tool, such as a pick, to press through and mark the
plastic at the center of each hole. The indentations will help to center your bit
when you drill the holes. Remember that you’ll need to make multiple holes to
vent the sound from the loudspeaker, which will be beneath the top panel of
the box. The result is shown in Figure 3-108.
I placed all the components on the top panel, with the exception of the power
input jack, which I positioned at one end of the box. Naturally, each hole has to
be sized to fit its component, and if you have calipers, they’ll be very useful for
taking measurements and selecting the right drill bit. Otherwise, make your
best guess, too small being better than too large. A deburring tool is ideal for
slightly enlarging a hole so that a component fits snugly. This may be neces-
sary if you drill 3/16-inch holes for your 5-inch mm LEDs. Fractionally enlarge
each hole, and the LEDs should push in very snugly.
If your loudspeaker lacks mounting holes, you’ll have to glue it in place. I used
five-minute epoxy to do this. Be careful not to use too much. You don’t want
any of the glue to touch the speaker cone.
Drilling large holes in the thin, soft plastic of a project box can be a problem.
The drill bit tends to dig in and create a mess. You can approach this problem
in one of three ways:
1. Use a Forstner drill bit if you have one. It creates a very clean hole.
2. Drill a series of holes of increasing size.
3. Drill a smaller hole than you need, and enlarge it with a deburring tool.
Regardless of which approach you use, you’ll need to clamp or hold the top
panel of the project box with its outside surface face-down on a piece of scrap
wood. Then drill from the inside, so that your bit will pass through the plastic
and into the wood.
Finally, mount the components in the panel, as shown in Figure 3-109, and
turn your attention to the underneath part of the box.
Figure 3-107. A printed layout for the
switches, LEDs, and other components
has been taped to the underside of the
lid of the project box. An awl is pressed
through the paper to mark the center of
each hole to be drilled in the lid.
Figure 3-108. The exterior of the panel after
drilling. A small handheld cordless drill
can create a neat result if the holes were
marked carefully.

The circuit board will sit on the bottom, held in place with four #4-size ma-
chine screws (bolts) with washers and nylon-insert locknuts. You need to use
locknuts to eliminate the risk of a nut working loose and falling among com-
ponents where it can cause a short circuit.
You’ll have to cut the perfboard to fit, taking care not to damage any of the
components on it. Also check the underside the board for loose fragments of
copper traces after you finish cutting.
Drill bolt holes in the board, if necessary, taking care again not to damage any
components. Then mark through the holes to the plastic bottom of the box,
and drill the box. Countersink the holes (i.e., bevel the edges of a hole so that
a flat-headed screw will fit into it flush with the surrounding surface), push
the little bolts up from underneath, and install the circuit board. Be extremely
careful not to attach the circuit board too tightly to the project box. This can
impose bending stresses, which may break a joint or a copper trace on the
board.
I like to include a soft piece of plastic under the board to absorb any stresses.
Because you’re using locknuts, which will not loosen, there’s no need to make
them especially tight.
Test the circuit again after mounting the circuit board, just in case.
Soldering the Switches
Figure 3-110 shows how the physical switches should be wired together. Re-
member that S1 is a toggle switch and S2 is a DPDT pushbutton.Your first step
is to decide which way up they should be. Use your meter to find out which
terminals are connected when the switch is flipped, and when the button is
pressed. You’ll probably want the switch to be on when the toggle is flipped
upward. Be especially careful with the orientation of the pushbutton, because
if you wire it upside-down, it will constantly have the alarm in “test” mode,
which is not what you want.
Remember, the center terminal of any double-throw switch is almost always
the pole of the switch, connecting with the terminals immediately above it
and below it.
Stranded wire is appropriate to connect the circuit board with the compo-
nents in the top panel, because the strands flex easily and impose less stress
on solder joints. Twisting each pair of wires together helps to minimize the
mess.
Remember to install the LEDs with their short, negative wires connected with
the resistor. This will entail some wire-to-wire soldering. You may want to pro-
tect some of these bare leads and joints with thin heat-shrink tubing, to mini-
mize the risk of short circuits when you push all the parts into the box.
When you connect wires or components with the lugs on the switches, your
pencil-style soldering iron probably won’t deliver enough heat to make good
joints. You can use your higher-powered soldering iron in these locations, but
you absolutely must apply a good heat sink to protect the LEDs when you
Figure 3-109. Components have been
added to the control panel of the project
box (seen from the underside). The loud-
speaker has been glued in place. Spare
glue was dabbed onto the LEDs, just in
case. The SPDT on/off switch is at the top
right, the DPDT pushbutton is at top left,
and the binding posts, which will con-
nect with the network of magnetic sensor
switches, are at the bottom.

Chapter 3144
attach them, and don’t allow the iron to remain in contact with anything for
more than 10 seconds. It will quickly melt insulation, and may even damage
the internal parts of the switches.
In projects that are more complex than this one, it would be good practice
to link the top panel with the circuit board more neatly. Multicolored ribbon
cable is ideal for this purpose, with plug-and-socket connectors that attach to
the board. For this introductory project, I didn’t bother. The wires just straggle
around, as shown in Figure 3-111.
To/From
Sensor
Switches
Power In
12V DC
S1
S2
To Circuit
Board
Power to
Circuit
Board
Normally Closed
Normally Open
(push to test)
Off
On
680 ohms
Figure 3-110. The components can be wired together like this to
replicate the circuit shown in The red and green circles are LEDs.
Small, solid black circles indicate wire-to-wire solder joints.
Figure 3-111. The circuit board has been installed in the
base of the project box, and the power input jack has been
screwed into the end of the box. Twisted wire-pairs have
been connected on a point-to-point basis, without much
concern over neatness, as this is a relatively small project.
The white insulation at the top-right corner of the front
panel is heat-shrink tube that encloses a solder joint and the
680Ω load resistor. Soldering wires to the pushbutton switch
requires care and precision, as the contacts are closely
spaced.

Final Test
When you’ve completed the circuit, test it! If you don’t have your network of
magnetic sensor switches set up yet, you can just use a piece of wire to con-
nect the two binding posts. Make sure that S1 is in its Off position, then solder
the appropriate plug to your 12-volt power source, and plug it into the power
jack. When you press the button, the green LED should light up to show con-
tinuity between the two binding posts. Now disconnect the wire between the
binding posts, press the button again, and the green LED should remain dark.
Reconnect the binding posts, flip S1 to its On position, and the red LED should
light up. Press the button, and the alarm should start. Reset it by turning S1
off and then on again; then disconnect the wire between the binding posts.
Again, the alarm should start, and it should continue even if you reconnect
the wire.
If everything works the way it should, it’s time to screw the top of the box in
place, pushing the wires inside. Because you’re using a large box, you should
have no risk of metal parts touching each other accidentally, but still, proceed
carefully.
Alarm Installation
Before you install your magnetic sensor switches, you should test each one by
moving the magnetic module near the switch module and then away from it,
while you use your meter to test continuity between the switch terminals. The
switch should close when it’s next to the magnet, and open when the magnet
is removed.
Now draw a sketch of how you’ll wire your switches together. Always remem-
ber that they have to be in series, not in parallel! Figure 3-112 shows the con-
cept in theory. The two terminals are the binding posts on top of your control
box (which is shown in green), and the dark red rectangles are the magnetic
sensor switches on windows and doors. Because the wire for this kind of instal-
lation usually has two conductors, you can lay it as I’ve indicated but cut and
solder it to create branches. The solder joints are shown as orange dots. Note
how current flows through all the switches in series before it gets back to the
control box.
Figure 3-113 shows the same network as you might actually install it in a situ-
ation where you have two windows and a door. The blue rectangles are the
magnetic modules that activate the switch modules.
You’ll need a large quantity of wire, obviously. The type of white, stranded
wire that is sold for doorbells or furnace thermostats is good. Typically, it is
20-gauge or larger.
After you install all the switches, clip your meter leads to the wires that would
normally attach to the alarm box. Set your meter to test continuity, and open
each window or door, one at a time, to check whether you’re breaking the
continuity. If everything is OK, attach the alarm wires to the binding posts on
your project box.
Figure 3-112. Dual-conductor, white
insulated wire can be used to connect the
terminals on the alarm control box with
magnetic sensors (shown in dark red).
Because the sensors must be in series, the
wire is cut and joined at positions marked
with orange dots.
Figure 3-113. In an installation involving two
windows and a door, the magnetic com-
ponents of the sensors (blue rectangles)
could be placed as shown, while the
switches (dark red) are located alongside
them.

Chapter 3146
Now deal with the power supply. Use your AC adapter, set to 12 volts, hooked
up to your type N power plug, or attach the power plug to a 12-volt alarm
battery.
If you use a battery, be especially careful that the wire leading to the center
terminal of your power plug is positive! A 12-volt battery can deliver substan-
tial current, which can fry your components if you connect it the wrong way
around. It would be a shame to destroy your entire project at the very last step.
The only remaining task is to label the switch, button, power socket, and bind-
ing posts on the alarm box. You know that the switch turns the power on and
off, and the button tests the circuit and the noisemaker, but no one else knows,
and you might want to allow a guest to use your alarm while you’re away. For
that matter, months or years from now, you may forget some details. Will you
remember that the power source for this unit should be 12 volts?
Labeling really is a good idea. But as you can see in Figure 3-114, I haven’t quite
gotten around to it for the box that I built.
Conclusion
The alarm project has taken you through the basic steps that you will usually
follow any time you develop something:
1. Draw a schematic and make sure that you understand it.
2. Modify it to fit the pattern of conductors on a breadboard.
3. Install components on the breadboard and test the basic functions.
4. Modify or enhance the circuit, and retest.
5. Transfer to perforated board, test, and trace faults if necessary.
6. Add switches, buttons, power jack, and plugs or sockets to connect the
circuit with the outside world.
7. Mount everything in a box (and add labeling).
While going through this sequence, I hope you’ve learned the basics of elec-
tricity, along with some simple electrical theory, and fundamentals about
electronic components. This knowledge should enable you to move on to the
much more powerful realm of integrated circuit—which I’ll cover in Chapter 4.
Figure 3-114. The intrusion alarm com-
pleted and in its project box.

4
147
Chips, Ahoy!
Before I get into the fascinating topic of integrated circuit (IC) chips, I have to
make a confession: some of the things I asked you to do in Chapter 3 could
have been done a bit more simply. Does this mean you have been wasting
your time? No, I firmly believe that by building circuits with old-fashioned
components—capacitors, resistors, and transistors—you acquire the best
possible understanding of the principles of electronics. Still, you are going to
find that integrated circuit chips, containing dozens, hundreds, or even thou-
sands of transistor junctions, will enable some shortcuts.
Tools
The only new tool that I recommend using in conjunction with chips is a logic
probe. This tells you whether a single pin on a chip has a high or low voltage,
which can be helpful in figuring out what your circuit is doing. The probe has
a memory function so that it will light its LED, and keep it lit, in response to a
pulse that may have been too quick for the eye to see.
Search online and buy the cheapest logic probe you can find. I don’t have any
specific brand recommendations. The one shown in Figure 4-1 is fairly typical.
Supplies
Integrated circuit chips
If you buy everything on this shopping list, and you bought basic parts
such as resistors and capacitors that were listed previously, you should
have everything you need for all the projects in this chapter.
As chips are quite cheap (currently around 50 cents apiece), I suggest you
buy extras. This way, if you damage one, you’ll have some in reserve.You’ll
also have a stock for future projects.
Please read the next section,“Fundamentals: Choosing chips,”before you
begin chip-shopping. Chips should be easily obtainable from all the major
electronics retail suppliers, and sometimes are found on eBay shops. Look
in the appendix for a complete list of URLs.
Figure 4-1. A logic probe detects the high or
low voltage on each pin of a chip, and re-
veals pulses that may occur too quickly for
you to perceive them with the unaided eye.
In this chapter
Experiment 16: Emitting a Pulse
Experiment 17: Set Your Tone
Experiment 18: Reaction Timer
Experiment 19: Learning Logic
Experiment 20: A Powerful Combination
Experiment 21: Race to Place
Experiment 22: Flipping and Bouncing
Experiment 23: Nice Dice
Experiment 24: Intrusion Alarm
Completed

Chapter 4148
Fundamentals
Choosing chips
Figure 4-2 shows what is often referred to as an integrated
circuit (IC). The circuit is actually etched onto a tiny wafer or
“chip”of silicon, embedded in a black plastic body, which is
properly referred to as the“package.”Tiny wires inside the
package link the circuit with the two rows of pins on either
side. Throughout this book, I will use the word“chip”to refer
to the whole object, including its pins, as this is the most
common usage.
Figure 4-2. An integrated circuit chip in Plastic Dual-Inline Pin
package, abbreviated PDIP, or, more often, DIP.
The pins are mounted at intervals of 1/10 inch in two rows
spaced 3/10 inch apart. This format is known as a Plastic
Dual Inline Package, abbreviated PDIP, or, more often, just
DIP. The chip in the photograph has four pins in each row;
others may have many more. The first thing you need to
know, when shopping for chips, is that you’ll only be using
the DIP package. This book will not be featuring the more
modern type, known as“surface-mount,”because they’re
much smaller, more difficult to handle, and require special
tools that are relatively expensive. Figure 4-3 shows a size
comparison between a 14-pin DIP package and a 14-pin
surface-mount package. Many surface-mount chips are
even smaller than the one shown.
Just about every chip has a part number printed on it. In
Figure 4-2, the part number is KA555. In Figure 4-3, the DIP
chip’s part number is M74HC00B1, and the surface-mount
chip is a 74LVC07AD. You can ignore the second line of
numbers and/or letters on each chip, as they are not part of
the part number.
Notice in Figure 4-3 that even though the chips look quite
different from each other, they both have“74”in their part
numbers. This is because both of them are members of the
“7400”family of logic chips, which originally had part numbers
from 7400 and upward (7400, 7401, 7402, 7403, and so on).
Often they are now referred to as“74xx”chips, where“xx”
includes all the members of the family. I’ll be using this fam-
ily a lot, so you need to know how to buy them. I’ll give you
some advice on that without going into details yet about
what the chips actually do.
Figure 4-3. The DIP chip, at the rear, has pins spaced 1/10
inch apart, suitable for insertion in a breadboard or perfo-
rated board. It can be soldered without special tools. The
small-outline integrated circuit (SOIC) surface-mount chip
(foreground) has solder tabs spaced at 1/20 inch. Other
surface-mount chips have pins spaced at 1/40 inch or even
less (these dimensions are often expressed in millimeters).
Surface-mount chips are designed primarily for automated
assembly and are difficult to work with manually. In this photo,
the yellow lines are 1 inch apart to give you an idea of the scale.
Take a look at Figure 4-4, which shows how to interpret a
typical part number in a 74xx family member. The initial
letters identify the manufacturer (which you can ignore,
as it really makes no difference for our purposes). Skip the
letters until you get to the“74.”After that, you find two more
letters, which are important. The 74xx family has evolved
through many generations, and the letter(s) inserted after
the“74”tell you which generation you’re dealing with. Some
generations have included:
• 74L
• 74LS
• 74C
• 74HC
• 74AHC
And there are more. Generally speaking, subsequent gen-
erations tend to be faster or more versatile than previous
generations. In this book, for reasons I’ll explain later, we are
mostly using the HC generation.

Chips, Ahoy! 149
Fundamentals
Choosing chips (continued)
After the letters identifying the generation, you’ll find two (sometimes more)
numerals. These identify the specific function of the chip. You can ignore any
remaining letters and numerals. Looking back at Figure 4-3, the DIP chip part
number, M74HC00B1 tells you that it is a chip in the 74xx family, HC generation,
with its function identified by numerals 00. The surface-mount chip number,
74LVC07AD, tells you that it is in the 74xx family, LVC generation, with function
identified by numerals 07. For convenience we could refer to the first chip as a
“74HC00”and the second chip as a“74HC07”because, regardless of their differ-
ent manufacturers and package sizes, the fundamental behavior of the circuit
inside remains the same.
The purpose of this long explanation is to enable you to interpret catalog list-
ings when you go chip shopping. You can search for“74HC00”and the online
vendors are usually smart enough to show you appropriate chips from multiple
manufacturers, even though there are letters preceding and following the term
that you’re searched for.
Suppose a circuit requires a 74HC04 chip. If you search for“74HC04”on the
website of a parts supplier, you may find versions such as the CD74HC04M96 by
Texas Instruments, the 74HC04N by NXP Semiconductors, or MM74HC04N by
Fairchild Semiconductor. Because they all have“74HC04”in the middle, any of
them will work.
Just be careful that you buy the larger DIP-style package, not the surface-mount
package. If the part number has an“N”on the end, you can be sure that it’s a DIP
package. If there is no“N”on the end, it may or may not be a DIP package, and
you will have to check a photo or additional description to make sure. If the part
number begins with SS, SO, or TSS, it’s absolutely definitely surface-mount, and
you don’t want it. Many catalogs show photographs of the chips to assist you in
buying the right package style.
Manufacturer
Texas Instruments
Type of chip
7400 NAND gate
Generation of chip
High Speed CMOS
Package format
Dual in-line pin
Figure 4-4. Look for the chip family (74xx, in this case) with the correct generation
(HC, in this case) embedded in the number. Make sure you buy the DIP version, not
the surface-mount version. The manufacturer is unimportant.

Chapter 4150
Here’s your chip list:
• 555 Timer. STMicroelectronics SA555N, Fairchild NE555D, RadioShack
TLC555, or similar. Do not get the“CMOS”version of this chip, or any fancy
versions such as those of high precision. Buy the cheapest you can find.
Quantity: 10. The chip in Figure 4-2 is a 555 timer.
• Logicchipstypes74HC00,74HC02,74HC04,74HC08,74HC32,and74HC86.
ActualpartnumberscouldbeM74HC00B1,M74HC02B1,M74HC04B1,and
so on, by STMicroelectronics, or SN74HC00N, SN74HC02N, SN74HC04N,
and so on, by Texas Instruments. Any other manufacturers are acceptable.
• Remember, each part number should have “HC” in the middle of it, and
you want the DIP or PDIP package, not surface-mount. Quantity of each:
At least 4.
• 4026 Decade Counter (a chip that counts in tens). Texas Instruments CD-
4026BE or similar. Quantity: 4 (you’ll need 3, but because this is a CMOS
chip sensitive to static electricity, you should have at least one in reserve).
Any chip with“4026”in its part number should be OK.
• 74LS92 counter chip, 74LS06 open-collector inverter chip, and 74LS27
triple-input NOR chip. Quantity: 2 of each. Note the “LS” in these part
numbers! There will be one experiment in which I want you to use the LS
generation instead of the HC generation.
IC sockets
I suggest that you avoid soldering chips directly onto perforated board. If
you damage them, they’re difficult to remove. Buy some DIP sockets, solder
the sockets onto the board, and then plug the chips into the sockets. You
can use the cheapest sockets you can find (you don’t need gold-plated con-
tacts for our purposes). You will need 8-pin, 14-pin, and 16-pin DIP sockets,
such as parts 276-1995, 276-1999, and 276-1998 from RadioShack. See Fig-
ure 4-5. Quantity of each: 5 minimum.
Low-power LEDs
The logic chips that you’ll be using are not designed to deliver significant
power.You’ll need to add transistors to amplify their output if you want to
drive bright LEDs or relays. Because adding transistors is a hassle, I suggest
an alternative: Special low-power LEDs that will draw as little as 1mA, such
as the Everlight model T-100 Low Current Red, part number HLMPK150.
Figure 4-6 shows a size comparison with a regular 5mm LED. Quantity: 10
(at a minimum).
LED numeric displays
In at least one of our projects, you’ll want to illuminate some seven-segment
LED numerals. You’ll need either three individual numerals, or one package
containing three numerals, such as the Kingbright High Efficiency Red Dif-
fused, part number BC56-11EWA, which will be specifically referred to in
schematics in this book. If you buy a different seven-segment display, it must
be an LED with a “common cathode.” (Don’t buy liquid-crystal LCD numer-
als; they require different electronics to drive them.) If you have a choice of
power consumption, buy whichever product consumes the least current.
See Figure 4-7.
Figure 4-5. When you’re soldering a circuit
onto perforated board, sockets eliminate
the risk of overheating integrated circuit
chips and reduce the risk of zapping them
with static electricity, and enable easy
replacement.
Figure 4-6. An HC series logic chip is rated
to deliver only 4mA at each pin. This is
inadequate to drive a typical 5 mm LED
(right), which is rated for 20mA forward
current. Miniature, low-current LEDs (left)
will use as little as 1mA in series with a
suitable resistor, and are ideal for test cir-
cuits in which you want to see the output
with a minimum of hassle.
Figure 4-7. Seven-segment displays are the
simplest way to show a numeric output
and can be driven directly by some CMOS
chips. For finished projects, they are
typically mounted behind transparent red
acrylic plastic panels.

Chips, Ahoy! 151
Latching relays
You’re going to need a 5-volt latching relay that has two coils, instead of
one. The first coil flips the relay one way; the second coil flips it back. The
relay consumes no additional power while remaining passively in each
state. I suggest the Panasonic DS2E-SL2-DC5V relay. If you buy a different
relay, it must be dual-coil latching to run off 5 volts DC, switching at least
1 amp, in a“2 form C”package, to fit your breadboard.
Potentiometers
You’ll need 5K, 10K, and 100K linear potentiometers (one of each). Also, a
10K trimmer potentiometer (which you may find described just as a“trim-
mer”). The manufacturer is unimportant.
Voltage regulators
Because many logic chips require precisely 5 volts DC, you need a voltage
regulator to deliver this. The LM7805 does the job. Here again, the chip
number will be preceded or followed with an abbreviation identifying the
manufacturer and package style, as in the LM7805CT from Fairchild. Any
manufacturer will do, but the package should look like the one in Figure
4-8, and if you have a choice, buy a regulator that can deliver at least 1
amp.
Tactile switches
These are SPST pushbuttons (momentary switches), usually with four legs.
Look for the ALPS part number SKHHAKA010 or any similar item that has
pins to fit your breadboard or perforated board. See Figure 4-9.
12-key numeric keypad
Velleman “12 keys keyboard with common output” (no part number, but
has been available through All Electronics under catalog code KP-12).
Quantity: 1.
This type of keypad has the same layout as an old-fashioned touchtone
phone. It should have at least 13 pins or contacts, 12 of which connect
with individual pushbuttons, the thirteenth connecting with the other
side of all the pushbuttons. In other words, the last pin is“common”to all
of them, and this type of keypad is often described as having a“common
output.”The type of keypad that you don’t want is“matrix-encoded,”with
fewer than 13 contacts, requiring additional external circuitry. See Figures
4-10 and 4-11. If you can’t find the Velleman keypad that I suggest, look
carefully at keypad descriptions and photographs to make sure that the
one you buy is not matrix-encoded and has a common terminal.
Alternatively, you may substitute 12 cheap SPST NO pushbuttons and
mount them in a small project box.
Figure 4-8. Many integrated circuit chips
require a controlled power supply of
5 volts, which can be delivered by this
regulator when you apply 7.5 to 9 volts to
it. The lefthand pin is for positive input,
the center pin is a common ground, and
the righthand pin is the 5V output. For cur-
rents exceeding 250mA, you should bolt
the regulator to a metal heat sink using
the hole at the top.
Figure 4-9. A tactile switch delivers tactile
feedback through your fingertip when you
press it. They are almost always SPST
pushbuttons designed for mounting in
circuit boards with standard 1/10-inch
hole spacing.

Chapter 4152
Figure 4-10. When shopping for a numeric
keypad, it should have 12 keys in “touch-
tone phone” layout, and should have at
least 13 contacts for input/output. The
contacts are visible here along the front
edge.
Figure 4-11. This keypad has insufficient
pins and will not work in the circuit in this
book.
Background
How chips came to be
The concept of integrating solid-state components into one
little package originated with British radar scientist Geoffrey
W. A. Dummer, who talked about it for years before he at-
tempted, unsuccessfully, to build one in 1956. The first true
integrated circuit wasn’t fabricated until 1958 by Jack Kilby,
working at Texas Instruments. Kilby’s version used germa-
nium, as this element was already in use as a semiconduc-
tor. (You’ll encounter a germanium diode when I deal with
crystal radios in the next chapter of this book.) But Robert
Noyce, pictured in Figure 4-12, had a better idea.
Born in 1927 in Iowa, in the 1950s Noyce moved to Cali-
fornia, where he found a job working for William Shockley.
This was shortly after Shockley had set up a business based
around the transistor, which he had coinvented at Bell Labs.
Noyce was one of eight employees who became frustrated
with Shockley’s management and left to establish Fairchild
Semiconductor. While he was the general manager of
Fairchild, Noyce invented a silicon-based integrated circuit
that avoided the manufacturing problems associated with
germanium. He is generally credited as the man who made
integrated circuits possible.
Early applications were for military use, as Minuteman
missiles required small, light components in their guidance
systems. These applications consumed almost all chips pro-
duced from 1960 through 1963, during which time the unit
price fell from around $1,000 to $25 each, in 1963 dollars.
In the late 1960s, medium-scale integration chips emerged,
each containing hundreds of transistors. Large-scale inte-
gration enabled tens of thousands of transistors on one chip
by the mid-1970s, and today’s chips can contain as many as
several billion transistors.
Robert Noyce eventually cofounded Intel with Gordon
Moore, but died unexpectedly of a heart attack in 1990.You
can learn more about the fascinating early history of chip de-
sign and fabrication at http://www.siliconvalleyhistorical.org.
Figure 4-12. This picture of Robert Noyce, late in his career, is
from the Wikimedia Commons.

Chips, Ahoy! 153
I’m going to introduce you to the most successful chip ever made: the 555
timer. As you can find numerous guides to it online, you might question the
need to discuss it here, but I have three reasons for doing so:
1. It’s unavoidable. You simply have to know about this chip. Some sources
estimate that more than 1 billion are still being manufactured annually.
It will be used in one way or another in most of the remaining circuits in
this book.
2. It provides a perfect introduction to integrated circuits, because it’s ro-
bust, versatile, and illustrates two functions that we’ll be dealing with
later: comparators and a flip-flop.
3. After reading all the guides to the 555 that I could find, beginning with the
original Fairchild Semiconductor data sheet and making my way through
various hobby texts, I concluded that its inner workings are seldom ex-
plained very clearly. I want to give you a graphic understanding of what’s
happening inside it, because if you don’t have this, you won’t be in a good
position to use the chip creatively.
You will need:
• 9-volt power supply.
• Breadboard, jumper wires, and multimeter.
• 5K linear potentiometer. Quantity: 1.
• 555 timer chip. Quantity: 1.
• Assorted resistors and capacitors.
• SPST tactile switches. Quantity: 2.
• LED (any type). Quantity: 1.
Procedure
The 555 chip is very robust, but still, in theory, you can zap it with a jolt of static
electricity and kill it. Therefore, to be on the safe side, you should ground
yourselfbeforehandlingit.Seethe“Groundingyourself”warningonpage172
for details. Although this warning primarily refers to the type of chips known
as CMOS, which are especially vulnerable, grounding yourself is always a sen-
sible precaution.
Look for a small circular indentation, called the dimple, molded into the body
of the chip, and turn the chip so that the indentation is at the top-left corner
with the pins pointing down. Alternatively, if your chip is of the type with a
notch at one end, turn the chip so that the notch is at the top.
The pins on chips are always numbered counterclockwise, starting from the
top-left pin (next to the dimple). See Figure 4-13, which also shows the names
of the pins on the 555 timer, although you don’t need to know most of them
just yet.
Negative
(ground)
Trigger
Output
Reset
Positive
Discharge
Threshold
Control
1
2
3
4
8
7
6
5
Dimple
Notch
Pins
555
Timer
Figure 4-13. The 555 timer chip, seen from
above. Pins on chips are always numbered
counterclockwise, from the top-left corner,
with a notch in the body of the chip upper-
most, or a circular indentation at top-left,
to remind you which end is up.

Chapter 4154
Insert the chip in your breadboard so that its pins straddle the channel down
the center. Now you can easily feed voltages to the pins on either side, and
read signals out of them. See Figure 4-14 for a precise guide to placement, in
the first project. The timer is identified as “IC1,” because “IC” is the customary
abbreviation for“Integrated Circuit.”
R4
R7
R5
D1
C4
C3
9V
DC
IC1
R6
C5
R8
S1
S2
Volts
Figure 4-14. This circuit allows you to explore the behavior of the 555 timer chip. Use your
meter to monitor the voltage on pin 2 as shown. There are no resistors labeled R1, R2,
or R3 and no capacitors labeled C1 or C2, because they’ll be added in a later schematic.
Component values in this schematic:
R4: 100K
R5: 2K2
R6: 10K
R7: 1K
R8: 5K linear potentiometer
C5: 0.1 µF ceramic
IC1: 555 timer
S1, S2: SPST tactile switches (pushbuttons)
D1: Generic LED
R5 holds the trigger (pin 2) positive until S1 is pressed, which lowers the voltage depend-
ing on the setting of potentiometer R8. When the trigger voltage falls below 1/3 of the
power supply, the chip’s output (pin 3) goes high for a period determined by the values
of R4 and C4. S2 resets (zeros) the timer, by reducing the voltage to pin 4, the Reset. C3
smoothes the power supply, and C5 isolates pin 5, the control, so that it won’t interfere
with the functioning of this test circuit. (We’ll use the control pin in a future experiment.)
All integrated circuit chips require a power supply. The 555 is powered with
negative voltage applied to pin 1 and positive to pin 8. If you reverse the volt-
age accidentally, this can permanently damage the chip, so place your jumper
wires carefully.

Chips, Ahoy! 155
Set your power supply to deliver 9 volts. It will be convenient for this experiment
if you supply positive down the righthand side and negative down the lefthand
side of the breadboard, as suggested in Figure 4-14. C3 is a large capacitor, at
least 100 µF, which is placed across the power supply to smooth it out and pro-
vide a local store of charge to fuel fast-switching circuits, as well as to guard
against other transient dips in voltage. Although the 555 isn’t especially fast-
switching, other chips are, and you should get into the habit of protecting them.
Begin with the potentiometer turned all the way counterclockwise to maxi-
mize the resistance between the two terminals that we’re using, and when you
apply the probe from your meter to pin 2, you should measure about 6 volts
when you press S1.
Now rotate the potentiometer clockwise and press S1 again. If the LED doesn’t
light up, keep turning the potentiometer and pressing and releasing the but-
ton. When you’ve turned the potentiometer about two-thirds of the way, you
should see the LED light up for just over 5 seconds when you press and release
the button. Here are some facts that you should check for yourself:
• The LED will keep glowing after you release the button.
• You can press the button for any length of time (less than the timer’s cycle
time) and the LED always emits the same length of pulse.
• The timer is triggered by a fall in voltage on pin 2. You can verify this with
your meter.
• The LED is either fully on or fully off.You can’t see a faint glow when it’s off,
and the transition from off to on and on to off is very clean and precise.
Check Figure 4-16 to see how the components should look on your bread-
board, and then look at the schematic in Figure 4-15 to understand what’s
happening. I will be adding more components later, which I will be labeling R1,
R2, C1, and C2 to be consistent with data sheets that you may see for the 555
timer. Therefore, in this initial circuit the resistors are labeled R4 and up, and
capacitors C3 and up.
When S1 (the tactile switch) is open, pin 2 of the 555 timer receives positive
power through R5, which is 2K2. Because the input resistance of the timer is
very high, the voltage on pin 2 is almost the full 9 volts.
When you press the button, it connects negative voltage through R8, the 5K
potentiometer to pin 2. Thus, R8 and R5 form a voltage divider with pin 2 in
the middle.You may remember this concept from when you were testing tran-
sistors. The voltage between the resistances will change, depending on the
values of the resistances.
If R8 is turned up about halfway, it is approximately equal to R5, so the mid-
point, connected to pin 2, has about half the 9-volt power supply. But when
you turn the potentiometer so that its resistance falls farther, the negative volt-
age outweighs the positive voltage, so the voltage on pin 2 gradually drops.
If you have clips on your meter leads, you can hook them onto the nearest
jumper wires and then watch the meter while you turn the potentiometer up
and down and press the button.
1
2
3
4 5
6
7
8
IC1
R5R8
R7
D1
C4
R4
C5
C3
S1
S2
9V
DC
R6
Figure 4-15. A schematic view of the circuit
shown in Figure 4-14. Throughout this
chapter, the schematics will be laid out
to emulate the most likely placement of
components on a breadboard. This is not
always the simplest layout, but will be
easiest for you to build. Refer to Figure
4-14 for the values of the components.
Figure 4-16. This is how the components
look when installed on the breadboard.
The alligator clips are attached to a patch
cord that links the 100 µF capacitor to the
potentiometer. The power supply input is
not shown.

Chapter 4156
The graphs in Figure 4-17 illustrate what is happening. The upper graph shows
the voltage applied to pin 2 by random button-presses, with the potentiometer
turned to various values. The lower graph shows that the 555 is triggered if,
and only if, the voltage on pin 2 actively drops from above 3 volts to below 3
volts. What’s so special about 3 volts? It’s one-third of our 9-volt power supply.
Here’s the take-home message:
• The output of the 555 (pin 3) emits a positive pulse when the trigger (pin
2) drops below one-third of the supply voltage.
• The 555 delivers the same duration of positive pulse every time (so long as
you don’t supply a prolonged low voltage on pin 2).
• A larger value for R4 or for C4 will lengthen the pulse.
• When the output (pin 3) is high, the voltage is almost equal to the supply
voltage. When the output goes low, it’s almost zero.
The 555 converts the imperfect world around it into a precise and dependable
output. It doesn’t switch on and off absolutely instantly, but is fast enough to
appear instant.
Now here’s another thing to try. Trigger the timer so that the LED lights up.
While it is illuminated, press S2, the second button, which grounds pin 4, the
reset. The LED should go out immediately.
When the reset voltage is pulled low, the output goes low, regardless of what
voltage you apply to the trigger.
There’s one other thing I want you to notice before we start using the timer for
more interesting purposes. I included R5 and R6 so that when you first switch
on the timer, it is not emitting a pulse—but is ready to do so. These resistors
apply a positive voltage to the trigger and the reset pin, to make sure that the
555 timer is ready to run when you first apply power to it.
As long as the trigger voltage is high, the timer will not emit a pulse. (It emits a
pulse when the trigger voltage drops.)
As long as the reset voltage is high, the timer is able to emit a pulse. (It shuts
down when the reset voltage drops.)
R5 and R6 are known as “pull-up resistors” because they pull the voltage up.
You can easily overwhelm them by adding a direct connection to the negative
side of the power supply. A typical pull-up resistor for the 555 timer is 10K.
With a 9-volt power supply, it only passes 0.9mA (by Ohm’s Law).
Finally, you may be wondering about the purpose of C5, attached to pin 5.This
pin is known the “control” pin, which means that if you apply a voltage to it,
you can control the sensitivity of the timer. I’ll get to this in more detail a little
later. Because we are not using this function right now, it’s good practice to
put a capacitor on pin 5 to protect it from voltage fluctuations and prevent it
from interfering with normal functioning.
Make sure you become familiar with the basic functioning of the 555 timer
before you continue.

Chips, Ahoy! 157
0v
3v
6v
9v
0v
3v
6v
9v
pulse width remains
fixed at 5.2 seconds
Pressing and releasing the button for varying intervals
while adjusting the voltage with the potentiometer
Output
Voltage
Pin 3
Trigger
Voltage
Pin 2
Figure 4-17. The top graph shows voltage on the trigger (pin 2) when the pushbutton is
pressed, for different intervals, at different settings of the potentiometer. The lower graph
shows the output (pin 3), which rises until it is almost equal to the power supply, when the
voltage on pin 2 drops below 1/3 the full supply voltage.
Fundamentals
The following table shows 555 pulse duration in monos-
table mode:
• Duration is in seconds, rounded to two figures.
• The horizontal scale shows common resistor values
between pin 7 and positive supply voltage.
• The vertical scale shows common capacitor values
between pin 6 and negative supply voltage.
To calculate a different pulse duration, multiply resistance ×
capacitance × 0.0011 where resistance is in kilohms, capaci-
tance is in microfarads, and duration is in seconds.
47 µF 0.05 0.11 0.24 0.52 1.1 2.4 5.2 11 24 52
22 µF 0.02 0.05 0.11 0.24 0.53 1.1 2.4 5.3 11 24
10 µF 0.01 0.02 0.05 0.11 0.24 0.52 1.1 2.4 5.2 11
4.7 µF 0.01 0.02 0.05 0.11 0.24 0.52 1.1 2.4 5.2
2.2 µF 0.01 0.02 0.05 0.11 0.24 0.53 1.1 2.4
1.0 µF 0.01 0.02 0.05 0.11 0.24 0.52 1.1
0.47 µF 0.01 0.02 0.05 0.11 0.24 0.52
0.22 µF 0.01 0.02 0.05 0.11 0.24
0.1 µF 0.01 0.02 0.05 0.11
0.047 µF 0.01 0.02 0.05
0.022 µF 0.01 0.02
0.01 µF 0.01
1K 2K2 4K7 10K 22K 47K 100K 220K 470K 1M

Chapter 4158
Theory
Inside the 555 timer: monostable mode
The plastic body of the 555 timer contains a wafer of silicon on which are
etched dozens of transistor junctions in a pattern that is far too complex to be
explained here. However, I can summarize their function by dividing them into
groups, as shown in Figure 4-18. An external resistor and two external capaci-
tors are also shown, labeled the same way as in Figure 4-15.
The negative and positive symbols inside the chip are power sources which ac-
tually come from pins 1 and 8, respectively. I omitted the internal connections
to those pins for the sake of clarity.
The two yellow triangles are“comparators.”Each comparator compares two
inputs (at the base of the triangle) and delivers an output (from the apex of the
triangle) depending on whether the inputs are similar or different. We’ll be us-
ing comparators for other purposes later in this book.
R4
C4
1
2
555
TIMER
3
4 5
6
7
UP
FF
8
A
B
C5
DOWN
Figure 4-18. Inside the 555 timer. White lines indicate connections inside the chip.
A and B are comparators. FF is a flip-flop which can rest in one state or the other,
like a double-throw switch. A drop in voltage on pin 2 is detected by comparator A,
which triggers the flip-flop into its “down” position and sends a positive pulse out of
pin 3. When C4 charges to 2/3 of supply voltage, this is detected by comparator B,
which resets the flip-flop to its “up” position. This discharges C4 through pin 7.

Chips, Ahoy! 159
Theory
Inside the 555 timer: monostable mode (continued)
The green rectangle, identified as“FF,”is a“flip-flop.”I have depicted it as a
DPDT switch, because that’s how it functions here, although of course it is
really solid-state.
Initially when you power up the chip, the flip-flop is in its“up”position which
delivers low voltage through the output, pin 3. If the flip-flop receives a signal
from comparator A, it flips to its“down”state, and flops there. When it receives a
signal from comparator B, it flips back to its“up”state, and flops there. The“UP”
and“DOWN”labels on the comparators will remind you what each one does
when it is activated.
Flip-flops are a fundamental concept in digital electronics. Computers couldn’t
function without them.
Notice the external wire that connects pin 7 with capacitor C4. As long as the
flip-flop is“up,”it sinks the positive voltage coming through R4 and prevents the
capacitor from charging positively.
If the voltage on pin 2 drops to 1/3 of the supply, comparator A notices this, and
flips the flip-flop. This sends a positive pulse out of pin 3, and also disconnects
the negative power through pin 7. So now C4 can start charging through R4.
While this is happening, the positive output from the timer continues.
As the voltage increases on the capacitor, comparator B monitors it through pin
6, known as the threshold. When the capacitor accumulates 2/3 of the supply
voltage, comparator B sends a pulse to the flip-flop, flipping it back into its
original state. This discharges the capacitor through pin 7, appropriately known
as the discharge pin. Also, the flip-flop ends the positive output through pin 3
and replaces it with a negative voltage. This way, the 555 returns to its original
state.
I’ll sum up this sequence of events very simply:
1. Initially, the flip-flop grounds the capacitor and grounds the output (pin 3).
2. A drop in voltage on pin 2 to 1/3 the supply voltage or less makes the out-
put (pin 3) positive and allows capacitor C4 to start charging through R4.
3. When the capacitor reaches 2/3 of supply voltage, the chip discharges the
capacitor, and the output at pin 3 goes low again.
In this mode, the 555 timer is“monostable,”meaning that it just gives one pulse,
and you have to trigger it again to get another.
You adjust the length of each pulse by changing the values of R4 and C4. How
doyouknowwhichvaluestochoose?Checkthetableonpage157,whichgivesan
approximate idea and also includes a formula so that you can calculate values
of your own.
I didn’t bother to include pulses shorter than 0.01 second in the table, because
a single pulse of this length is usually not very useful. Also I rounded the num-
bers in the table to 2 significant figures, because capacitor values are seldom
more accurate than that.

Chapter 4160
Background
How the timer was born
Back in 1970, when barely a half-dozen corporate seedlings had taken root
in the fertile ground of Silicon Valley, a company named Signetics bought an
idea from an engineer named Hans Camenzind. It wasn’t a huge breakthrough
concept—just 23 transistors and a bunch of resistors that would function as a
programmable timer. The timer would be versatile, stable, and simple, but these
virtues paled in comparison to its primary selling point. Using the emerging
technology of integrated circuits, Signetics could reproduce the whole thing on
a silicon chip.
This entailed some trial and error. Camenzind worked alone, building the whole
thing initially on a large scale, using off-the-shelf transistors, resistors, and di-
odes on a breadboard. It worked, so then he started substituting slightly differ-
ent values for the various components to see whether the circuit would tolerate
variations during production and other factors such as changes in temperature
when the chip was in use. He made at least 10 different versions of the circuit. It
took months.
Next came the crafts work. Camenzind sat at a drafting table and used a
specially mounted X-Acto knife to scribe his circuit into a large sheet of plastic.
Signetics then reduced this image photographically by a ratio of about 300:1.
They etched it into tiny wafers, and embedded each of them in a half-inch
rectangle of black plastic with the product number printed on top. Thus, the
555 timer was born.
It turned out to be the most
successful chip in history, both
in the number of units sold (tens
of billions and counting) and the
longevity of its design (unchanged
in almost 40 years). The 555 has
been used in everything from toys
to spacecraft. It can make lights
flash, activate alarm systems, put
spaces between beeps, and create
the beeps themselves.
Today, chips are designed by large
teams and tested by simulating
their behavior using computer soft-
ware.Thus, chips inside a computer
enable the design of more chips.
The heyday of solo designers such
as Hans Camenzind is long gone,
but his genius lives inside every 555
timer that emerges from a fabrica-
tion facility. (If you’d like to know
more about chip history, see http://
www.semiconductormuseum.com/
Museum_Index.htm.)
Figure 4-19. Hans Camenzind, inventor
and developer of the 555 timer chip for
Signetics.

Chips, Ahoy! 161
Fundamentals
Why the 555 is useful
In its monostable mode (which is what you just saw), the
555 will emit a single pulse of fixed (but programmable)
length. Can you imagine some applications? Think in terms
of the pulse from the 555 controlling some other compo-
nent. A motion sensor on an outdoor light, perhaps. When
an infra-red detector“sees”something moving, the light
comes on for a specific period—which can be controlled by
a 555.
Another application could be a toaster. When someone low-
ers a slice of bread, a switch will close that triggers the toast-
ing cycle. To change the length of the cycle, you could use
a potentiometer instead of R4 and attach it to the external
lever that determines how dark you want your toast. At the
end of the toasting cycle, the output from the 555 would
pass through a power transistor, to activate a solenoid
(which is like a relay, except that it has no switch contacts)
to release the toast.
Intermittent windshield wipers could be controlled by a 555
timer—and on earlier models of cars, they actually were.
And what about the burglar alarm that was described at the
end of Chapter 3? One of the features that I listed, which has
not been implemented yet, is that it should shut itself off
after a fixed interval. We can use the change of output from
a 555 timer to do that.
The experiment that you just performed seemed trivial, but
really it implies all kinds of possibilities.
555 timer limits
1. The timer can run from a stable voltage source ranging
from 5 to 15 volts.
2. Most manufacturers recommend a range from 1K to
1M for the resistor attached to pin 7.
3. The capacitor value can go as high as you like, if you
want to time really long intervals, but the accuracy of
the timer will diminish.
4. The output can deliver as much as 100mA at 9 volts.
This is sufficient for a small relay or miniature loud-
speaker, as you’ll see in the next experiment.
Beware of Pin-Shuffling!
In all of the schematics in this book, I’ll show chips as you’d see them
from above, with pin 1 at top left. Other schematics that you may
see, on websites or in other books, may do things differently. For
convenience in drawing circuits, people shuffle the pin numbers on
a chip so that pin 1 isn’t necessarily shown adjacent to pin 2.
Look at the schematic in Figure 4-20 and compare it with the one
in Figure 4-15. The connections are the same, but the one in Figure
4-20 groups pins to reduce the apparent complexity of the wiring.
“Pin shuffling” is common because circuit-drawing software tends
to do it, and on larger chips, it is necessary for functional clarity of
the schematic (i.e., logical groupings of pin names versus physical
groupings on memory chips, for example). When you’re first learn-
ing to use chips, I think it’s easier to understand a schematic that
shows the pins in their actual positions. So that’s the practice I will
be using here.
R5
R8
61
3
2
5 4
7
8
IC1
C3
C1
R4
S2
R7
D1
S1
R6
C2
9V
DC
Figure 4-20. Many people draw schematics in which the pin numbers on a chip are shuffled around to make the schematic
smaller or simpler. This is not helpful when you try to build the circuit. The schematic here is for the same circuit as in Figure
4-15. This version would be harder to recreate on a breadboard.

Chapter 4162
I’m going to show you two other ways in which the 555 timer can be used.
You will need the same items as in Experiment 16, plus:
• Additional 555 timer chip. Quantity: 1.
• Miniature loudspeaker. Quantity: 1.
• 100K linear potentiometer. Quantity: 1.
Procedure
Leave the components from Experiment 16 where they are on the bread-
board, and add the next section below them, as shown in Figures 4-21 and
4-22. Resistor R2 is inserted between pins 6 and 7, instead of the jumper wire
that shorted the pins together in the previous circuit, and there’s no external
input to pin 2 anymore. Instead, pin 2 is connected via a jumper wire to pin
6. The easiest way to do this is by running the wire across the top of the chip.
I have omitted the smoothing capacitor from the schematic in Figure 4-22,
because I’m assuming that you’re running this circuit on the same breadboard
as the first, where the previous smoothing capacitor is still active.
A loudspeaker in series with a 100Ω resistor (R3) has been substituted for the
LED to show the output from the chip. Pin 4, the reset, is disabled by connect-
ing it to the positive voltage supply, as I’m not expecting to use the reset func-
tion in this circuit.
Now what happens when you apply power? Immediately, you should hear
noise through the loudspeaker. If you don’t hear anything, you almost cer-
tainly made a wiring error.
Notice that you don’t have to trigger the chip with a pushbutton anymore.
The reason is that when C1 charges and discharges, its fluctuating voltage is
connected via a jumper wire across the top of the chip to pin 2, the trigger. In
this way, the 555 timer now triggers itself. I’ll describe this in more detail in the
next section “Theory: Inside the 555 timer: astable mode,” if you want to see
exactly what is going on.
In this mode, the chip is“astable,”meaning that it is not stable, because it flips
to and fro endlessly, sending a stream of pulses for as long as the power is
connected. The pulses are so rapid that the loudspeaker reproduces them as
noise.
In fact, with the component values that I specified for R1, R2, and C1, the 555
chip is emitting about 1,500 pulses per second. In other words, it creates a 1.5
KHz tone.
Checkthetableonpage166toseehowdifferentvaluesforR2andC1cancreate
different pulse frequencies with the chip in this astable mode. Note that the
table assumes a fixed value of 1K for R1!

Chips, Ahoy! 163
Figure 4-21. These components should be
added on the same breadboard below the
components shown in Figure 4-14. Use the
following values to test the 555 timer in its
astable mode:
R1: 1K
R2: 10K
R3: 100Ω
C1: 0.047 µF ceramic or electrolytic
C2: 0.1 µF ceramic
IC2: 555 timer
R1
R2
R3
C1
9V
DC
IC2
C2
Loudspeaker
C3
Figure 4-22. This is the schematic version
of the circuit shown in Figure 4-21. The
component values are the same.
1
2
3
4 5
6
7
8
IC2
R1
R2
R3
C1C2
9V
DC

Chapter 4164
Theory
Inside the 555 timer: astable mode
Here’s what is happening now, illustrated in Figure 4-23.
Initially, the flip-flop grounds C1 as before. But now the low
voltage on the capacitor is connected from pin 7 to pin 2
through an external wire. The low voltage tells the chip to
trigger itself. The flip-flop obediently flips to its“on”position
and sends a positive pulse to the loudspeaker, while remov-
ing the negative voltage from pin 7.
R1
C1
1
2
3
4 5
6
7
FF
8
A
B
C2
R2
Figure 4-23. When the 555 timer is used in astable mode, resis-
tor R2 is placed between pin 6 and pin 7, and pin 6 is connected
via an external wire to pin 2, so that the timer triggers itself.
Now C1 starts charging, as it did when the timer was in
monostable mode, except that it is being charged through
R1 + R2 in series. Because the resistors have low values, and
C1 is also small, C1 charges quickly. When it reaches 2/3 full
voltage, comparator B takes action as before, discharging
the capacitor and ending the output pulse from pin 3.
The capacitor takes longer to discharge than before,
because R2 has been inserted between it and pin 7, the
discharge pin. While the capacitor is discharging, its voltage
diminishes, and is still linked to pin 2. When the voltage
drops to 1/3 of full power or less, comparator A kicks in and
sends another pulse to the flip-flop, starting the process all
over again.
Summing up:
1. In astable mode, as soon as power is connected, the
flip-flop pulls down the voltage on pin 2, triggering
comparator A, which flips the flip-flop to its“down”
position.
2. Pin 3, the output, goes high. The capacitor charges
through R1 and R2 in series.
3. When the capacitor reaches 2/3 of supply voltage, the
flip-flop goes“up”and the output at pin 3 goes low. The
capacitor starts to discharge through R2.
4. When the charge on the capacitor diminishes to 1/3 of
full voltage, the pull-down on pin 2 flips the flip-flop
again and the cycle repeats.
Unequal on/off cycles
When the timer is running in astable mode, C1 charges
through R1 and R2 in series. But when C1 discharges, it
dumps its voltage through R2 only. This means that the
capacitor charges more slowly than it discharges. While it is
charging, the output on pin 3 is high; while it is discharging,
the output on pin 3 is low. Consequently the“on”cycle is
always longer than the“off”cycle. Figure 4-24 shows this as
a simple graph.
If you want the on and off cycles to be equal, or if you want
to adjust the on and off cycles independently (for example,
because you want to send a very brief pulse to another chip,
followed by a longer gap until the next pulse), all you need
to do is add a diode, as shown in Figure 4-25.
Now when C1 charges, the electricity flows through R1 as be-
fore but takes a shortcut around R2, through diode D1. When
C1 discharges, the diode blocks the flow of electricity in that
direction, and so the discharge goes back through R2.

Chips, Ahoy! 165
Theory
Inside the 555 timer: astable mode (continued)
R1 now controls the charge time on its own, while R2 controls the discharge
time. The formula for calculating the frequency is now:
Frequency = 1440 / ((R1 + R2) × C1)
If you set R1 = R2, you should get almost equal on/off cycles (“almost”because
the diode itself imposes a small internal voltage drop of about 0.6V). The exact
value depends primarily on the manufacturing process used to make the diode.
0v
3v
6v
9v
Output
Voltage
Pin 3
Duration of each
On cycle is
proportionate to
R1+R2
Duration of each
Off cycle is
proportionate to
R2 only
Figure 4-24. In its usual astable configuration, the timer charges a capacitor through
R1+R2 and discharges the capacitor through R2 only. Therefore its output on cycles
are longer than its output off cycles.
1
2
3
4 5
6
7
8
IC2
R1
R2
R3
C1
D2
C2
9V
DC
Figure 4-25. This is a modification of the schematic shown in Figure 4-22. By adding
a diode to a 555 timer running in astable mode, we eliminate R2 from the charging
cycle of capacitor C1. Now we can adjust the output on cycle with the value of R1,
and the output off cycle with the value of R2, so that the on and off durations are
independent of each other.

Chapter 4166
Fundamentals
The following table shows 555 timer frequency in astable
mode:
• Frequency is in pulses per second, rounded to two
figures.
• The horizontal scale shows common resistor values for
R2.
• The vertical scale shows common capacitor values for
C1. Resistor R1 is assumed to be 1K.
• Resistor R1 is assumed to be 1K.
To calculate a different frequency: double R2, add the prod-
uct to R1, multiply the sum by C1, and divide the result into
1440. Like this:
Frequency = 1440 / ( (R1 + 2R2) × C1) cycles per second
In this formula, R1 and R2 are in kilohms, C1 is in microfarads,
and the frequency is in hertz (cycles per second). Note that
the frequency is measured from the start of one pulse to
the start of the next. The duration of each pulse is not the
same as the length of time between each pulse. This issue is
discussed in the previous section.
47 µF 10 5.7 3.0 1.5 0.7 0.3 0.2 0.1
22 µF 22 12 6.3 3.1 1.5 0.7 0.3 0.2 0.1
10 µF 48 27 14 6.9 3.2 1.5 0.7 0.3 0.2 0.1
4.7 µF 100 57 30 15 6.8 3.2 1.5 0.7 0.3 0.2
2.2 µF 220 120 63 31 15 6.9 3.3 1.5 0.7 0.3
1.0 µF 480 270 140 69 32 15 7.2 3.3 1.5 0.7
0.47 µF 1,000 570 300 150 68 32 15 7 3.3 1.5
0.22 µF 2,200 1,200 630 310 150 69 33 15 7 3.3
0.1 µF 4,800 2,700 1,400 690 320 150 72 33 15 7.2
0.047 µF 10,000 5,700 3,000 1,500 680 320 150 70 33 15
0.022 µF 22,000 12,000 6,300 3,100 1,500 690 330 150 70 33
0.01 µF 48,000 27,000 14,000 6,900 3,200 1,500 720 330 150 72
1K 2K2 4K7 10K 22K 47K 100K 220K 470K 1M
Astable Modifications
In the circuits shown in Figures 4-22 or 4-25, if you substitute a 100K potenti-
ometer for R2, you can adjust the frequency up and down by turning the shaft.
Another option is to “tune” the timer by using pin 5, the control, as shown in
the Figure 4-26. Disconnect the capacitor that was attached to that pin and
substitute the series of resistors shown. R9 and R11 are both 1K resistors, either
side of R10, which is a 100K potentiometer. They ensure that pin 5 always has
at least 1K between it and the positive and negative sides of the power supply.
Connecting it directly to the power supply won’t damage the timer, but will
prevent it from generating audible tones. As you turn the potentiometer to
and fro, the frequency will vary over a wide range. If you want to generate a
very specific frequency, a trimmer potentiometer can be used instead.

Chips, Ahoy! 167
A primary advantage of using pin 5 to adjust frequency is that you can control
it remotely. Take the output from pin 3 of another 555 timer running slowly in
astable mode, and pipe it through a 2K2 resistor to pin 5. Now you get a two-
tone siren effect, as one timer controls the other. If, in addition, you add a 100
µF capacitor between pin 5 and ground, the charging and discharging of the
capacitor will make the tone slide up and down instead of switching abruptly.
I’ll describe this in more detail shortly. This leads me to the whole topic of one
chip controlling another chip, whichwillbeourlast variationon this experiment.
Chaining Chips
Generally speaking, chips are designed so that they can talk to each other. The
555 couldn’t be easier in this respect:
• Pin 3, the output, from one 555 can be connected directly to pin 2, the
trigger, of a second 555.
• Alternatively, the output can be sufficient to provide power to pin 8 of a
second 555.
• The output is appropriate to control or power other types of chips too.
Figure 4-27 shows these options.
When the output from the first 555 goes high, it is about 70 to 80% of its sup-
ply voltage. In other words, when you’re using a 9V supply, the high output
voltage is at least 6 volts. This is still above the minimum of 5V that the second
chip needs to trigger its comparator, so there’s no problem.
1
2
3
4 5
6
7
9V power
input
8
IC1
1
2
3
4 5
6
7
8
IC2
From 0.5V
to 6V output
low-to-high
Now you
can control
me!
1
2
3
4 5
6
7
9V power
input
8
IC1
1
2
3
4 5
6
7
8
IC2
More than
5V output
when high That's still
high enough to
power me!
1
2
3
4 5
6
7
That's low
enough to
trigger me!
8
IC1
1
2
3
4 5
6
7
8
IC2
Less than
0.5 volts
when low
9V power
input
Figure 4-27. Three ways to chain 555 timers together. The output of IC1 can power a sec-
ond timer, or adjust its control voltage, or activate its trigger pin.
You can chain together the two 555 timers that you already have on your
breadboard. Figure 4-28 shows how to connect the two circuits that were
shown previously in Figures 4-15 and 4-22. Run a wire from pin 3 (the output)
of the first chip to pin 8 (the positive power supply) of the second chip, and
disconnect the existing wire connecting pin 8 to your power supply. The new
wire is shown in red. Now when you press the button to activate the first chip,
its output powers the second chip.
1
2
3
4 5
6
7
8
555
timer
R1
R2
R9 R10 R11
R3 C1
9V
DC
Figure 4-26. The control (pin 5) is seldom
used but can be useful. Varying the voltage
on it will adjust the speed of the timer. This
circuit enables you to test the behavior of
it. Component values:
R1: 1K
R2: 10K
R3: 100 ohms
R9, R11: 1K
R10: 100K linear potentiometer
C1: 0.047 µF

Chapter 4168
You can also use the output from one chip to trigger another (i.e., you can con-
nect pin 3 from the first chip to pin 2 of the second).When the output from the
first chip is low, it’s less than half a volt. This is well below the threshold that
the second chip requires to be activated.Why would you want to do this?Well,
you might want to have both timers running in monostable mode, so that the
end of a high pulse from the first one triggers the start of a high pulse in the
second one. In fact, you could chain together as many timers as you like in this
way, with the last one feeding back and triggering the first one, and they could
flash a series of LEDs in sequence, like Christmas lights. Figure 4-29 shows how
four timers could be linked this way, in a configuration that would occupy min-
imal space (and would be wired point-to-point on perforated board, not on
breadboard-format board). Each of the outputs numbered 1 through 4 would
have about enough power to run maybe 10 LEDs, if you used relatively high
load resistors to limit their current.
Incidentally, you can reduce the chip count (the number of chips) by using two
556 timers instead of four 555 timers. The 556 contains a pair of 555 timers in
one package. But because you have to make the same number of external con-
nections (other than the power supply), I haven’t bothered to use this variant.
You can even get a 558 timer that contains four 555 circuits, all preset to func-
tion in astable mode. I decided not to use this chip, because its output behaves
differently from a normal 555 timer. But you can buy a 558 timer and play with
it if you wish. It is ideal for doing the “chain of four timers” that I suggested
previously. The data sheet even suggests this.
Lastly, going back to the idea of modifying the frequency of a 555 timer in
astable mode, you can chain two timers, as shown in Figure 4-30. The red wire
shows the connection from the output of the first timer to the control pin of
the second. The first timer has now been rewired in astable mode, so that it
creates an oscillating on/off output around four times per second. This out-
put flashes the LED (to give you a visual check of what’s going on) and feeds
through R7 to the control pin of the second timer.
But C2 is a large capacitor, which takes time to charge through R7. While this
happens, the voltage detected by pin 5 slowly rises, so that the tone gener-
ated by IC2 gradually rises in pitch. Then IC1 reaches the end of its on cycle
and switches itself off, at which point C2 discharges and the pitch of the sound
generated by IC2 falls again.
You can tweak this circuit to create all kinds of sounds, much more controllably
then when you were using PUT transistors to do the same kind of thing. Here
are some options to try:
• Double or halve the value of C2.
• Omit C2 completely, and experiment with the value of R7.
• Substitute a 10K potentiometer for R7.
• Change C4 to increase or decrease the cycle time of IC1.
1
2
3
4 5
6
7
8
IC1
R4
S1
S2
D1
R5
R4
R8
C4C5
C3
9V
DC
10K
1
2
3
4 5
6
7
8
IC2
R1
R2
R3
C1C2
Figure 4-28. You can combine the two cir-
cuits shown in Figures 4-15 and 4-22 sim-
ply by disconnecting the wire that provides
power to pin 8 of the second timer, and
running a substitute wire (shown in red).
12V
DC
2
1
3
4
Figure 4-29. Four 555 timers, chained to-
gether in a circle, can flash a series of four
sets of LEDs in sequence, like Christmas
lights or a movie marquee.

Chips, Ahoy! 169
• Halve the value of R5 while doubling the value of C4, so that the cycle
time of IC1 stays about the same, but the On time becomes significantly
longer than the Off time.
• Change the supply voltage in the circuit from 9 volts to 6 volts or 12 volts.
Remember, you can’t damage a 555 timer by making changes of this kind. Just
make sure that the negative side of your power supply goes to pin 1 and the
positive side to pin 8.
C3
1
2
3
4 5
6
7
8
IC2
R1
R2
R3
C1
1
2
3
4 5
6
7
8
IC1
R4
R5
C4
R6
R7
D1
C2
C5
9V
DC
Figure 4-30. When both timers are astable, but IC1 runs much more slowly than IC2, the
output from IC1 can be used to modulate the tone generated by IC2. Note that as this is
a substantial modification to the previous schematics, several components have been
relabeled. To avoid errors, you may need to remove the old circuit from your breadboard
and build this version from scratch. Try these values initially:
R1, R4, R6, R7: 1K
R2, R5: 10K
R3: 100 ohms
C1: 0.047 µF
C2, C3: 100 µF
C4: 68 µF
C5: 0.1 µF

Chapter 4170
Because the 555 can easily run at thousands of cycles per second, we can use it
to measure human reactions.You can compete with friends to see who has the
fastest response—and note how your response changes depending on your
mood, the time of day, or how much sleep you got last night.
Before going any further, I have to warn you that this circuit will have more
connections than others you’ve tackled so far. It’s not conceptually difficult,
but requires a lot of wiring, and will only just fit on a breadboard that has 63
rows of holes. Still, we can build it in a series of phases, which should help you
to detect any wiring errors as you go.
You will need:
• 4026 chip. Quantity: 4 (really you need only 3, but get another one in case
you damage the others).
• 555 timers. Quantity: 3.
• Tactile switches (SPST momentary switches). Quantity: 3.
• Three numeric LEDs, or one 3-digit LED display (see the shopping list at
the beginning of this chapter). Quantity: 1.
• Breadboard, resistors, capacitors, and meter, as usual.
Step 1: Display
You can use three separate LED numerals for this project, but I suggest that
you buy the Kingbright BC56-11EWA on the shopping list at the beginning of
this chapter. It contains three numerals in one big package.
You should be able to plug it into your breadboard, straddling the center
channel. Put it all the way down at the bottom of the breadboard, as shown in
Figure 4-31. Don’t put any other components on the breadboard yet.
Now set your power supply to 9 volts, and apply the negative side of it to the
row of holes running up the breadboard on the righthand side. Insert a 1K
resistor between that negative supply and each of pins 18, 19, and 26 of the
Kingbright display, which are the “common cathode,” meaning the negative
connection shared by each set of LED segments in the display. (The pin num-
bers of the chip are shown in Figure 4-33. If you’re using another model of
display, you’ll have to consult a data sheet to find which pin(s) are designed to
receive negative voltage.)
Switch on the power supply and touch the free end of the positive wire to each
row of holes serving the display on its left and right sides.You should see each
segment light up, as shown in Figure 4-31.
Each numeral from 0 to 9 is represented by a group of these segments. The
segments are always identified with lowercase letters a through g, as shown in
Figure 4-32. In addition, there is often a decimal point, and although we won’t
be using it, I’ve identified it with the letter h.
Figure 4-31. After putting a 1K resistor
between the common cathode of the
display and the negative supply voltage,
you can use the positive supply voltage to
illuminate each segment in turn.
a
g
d
bf
ce
h
Figure 4-32. The most basic and common
digital numeral consists of seven LED seg-
ments identified by letters, as shown here,
plus an optional decimal point.

Chips, Ahoy! 171
Check Figure 4-33 showing the Kingbright display, and you’ll see I have an-
notated each pin with its function. You can step down the display with the
positive wire from your power supply, making sure that each pin lights an ap-
propriate segment.
Incidentally, this display has two pins, numbered 3 and 26, both labeled to
receive negative voltage for the first of the digits.Why two pins instead of one?
I don’t know. You need to use only one, and as this is a passive chip, it doesn’t
matter if you leave the unused one unconnected. Just take care not to apply
positive voltage to it, which would create a short circuit.
A numeric display has no power or intelligence of its own. It’s just a bunch of
light-emitting diodes. It’s not much use, really, until we can figure out a way to
illuminate the LEDs in appropriate groups—which will be the next step.
Step 2: Counting
Fortunately, we have a chip known as the 4026, which receives pulses, counts
them, and creates an output designed to work with a seven-segment display so
that it shows numbers 0–9.The only problem is that this is a rather old-fashioned
CMOS chip (meaning, Complementary Metal Oxide Semiconductor) and is thus
sensitive to static electricity. Check the caution on page 172 before continuing.
Switch off your power supply and connect its wires to the top of the breadboard,
noting that for this experiment, we’re going to need positive and negative pow-
er on both sides. See Figure 4-34 for details. If your breadboard does not already
have the columns of holes color-coded, I suggest you use Sharpie markers to
identify them, to avoid polarity errors that can fry your components.
The 4026 counter chip is barely powerful enough to drive the LEDs in our dis-
play when powered by 9 volts. Make sure you have the chip the right way up,
and insert it into the breadboard immediately above your three-digit display,
leaving just one row of holes between them empty.
The schematic in Figure 4-35 shows how the pins of the 4026 chip should be con-
nected. The arrows tell you which pins on the display should be connected with
pins on the counter.
Figure 4-36 shows the“pinouts”(i.e., the functions of each pin) of a 4026 coun-
ter chip. You should compare this with the schematic in Figure 4-35.
Include a tactile switch between the positive supply and pin 1 of the 4026
counter, with a 10K resistor to keep the input to the 4026 counter negative un-
til the button is pressed. Make sure all your positives and negatives are correct,
and turn on the power. You should find that when you tap the tactile switch
lightly, the counter advances the numeric display from 0 through 9 and then
begins all over again from 0. You may also find that the chip sometimes misin-
terprets your button-presses, and counts two or even three digits at a time. I’ll
deal with this problem a little further on.
The LED segments will not be glowing very brightly, because the 1K series
resistors deprive of them of the power they would really like to receive. Those
resistors are necessary to avoid overloading the outputs from the counter.
1e 1
2
3
4
5
6
7
8
9
10
11
12
13
14
28
27
26
25
24
23
22
21
20
19
18
17
16
15
1d
1c
1h
2e
2d
2c
2h
3e
3d
3g
3c
3h
1g
1f
1a
11
2
3
1b
2f
2g
2a
2b
3f
3a
3b
a
g
d
bf
ce
a
g
d
bf
ce
a
g
d
bf
ce
hhh
Numeral 3
Numeral 2
Numeral 1
Figure 4-33. This Kingbright unit incor-
porates three seven-segment numeric
displays in one package, and can be driven
by three chained 4026 decade counters.
The pin numbers are shown close to the
chip. Segments a through g of numeral 1
are identified as 1a through 1g. Segments
a through g of numeral 2 are identified as
2a through 2g. Segments a through g of
numeral 3 are identified as 3a through 3g.
100uF
9v
DC
Figure 4-34. When building circuits around
chips, it’s convenient to have a positive
and negative power supply down each
side of your breadboard. For the reaction
timer circuit, a 9V supply with a 100 µF
smoothing capacitor can be set up like
this. If your breadboard doesn’t color-code
the columns of holes on the left and right
sides, I suggest you do that yourself with a
permanent marker.

Chapter 4172
GroundingYourself
To avoid the frustration that occurs when you power up a circuit and nothing happens, be sure to take these precautions when you
use the older generation of CMOS chips (which often have part numbers from 4000 upward, such as 4002, 4020, and so on):
Chips are often shipped with their legs embedded in black foam. This is electrically conductive foam, and you should keep the chips
embedded in it until you are ready to use them.
If the chips are supplied to you in plastic tubes, you can take them out and poke their legs into pieces of conductive foam or, if you
don’t have any, use aluminum foil. The idea is to avoid one pin on a chip acquiring an electric potential that is much higher than
another pin.
While handling CMOS components, grounding yourself is important. I find that in dry weather, I accumulate a static charge merely
by walking across a plastic floor-protecting mat in socks that contain some synthetic fibers. You can buy a wrist strap to keep your-
self grounded, or simply touch a large metal object, such as a file cabinet, before you touch your circuit board. I am in the habit of
working with my socked foot touching a file cabinet, which takes care of the problem.
Never solder a CMOS chip while there is power applied to it.
Grounding the tip of your soldering iron is a good idea.
Better still, don’t solder CMOS chips at all. When you’re ready to immortalize a project by moving it from a breadboard into perfo-
rated board, solder a socket into your perforated board, then push the chip into the socket. If there’s a problem in the future, you
can unplug the chip and plug in another.
Use a grounded, conductive surface on your workbench. The cheapest way to do this is to unroll some aluminum foil and ground
it (with an alligator clip and a length of wire) to a radiator, a water pipe, or a large steel object. I like to use an area of conductive
foam to cover my workbench—the same type of foam that is used for packaging chips. However, this foam is quite expensive.
Figure 4-35. IC3 is a 4026
counter. IC4 is a triple
seven-segment display chip.
The arrows tell you which
pins on the LED display
should be connected to the
pins on the counter.
1
2
3
4
5
6
7
8
16
15
14
13
12
11
10
9
1
2
3
4
5
6
7
8
9
10
11
12
13
14
28
27
26
25
24
23
22
21
20
19
18
17
16
15
IC3
IC4
R4
10K
R5
R6
27
28
4
1
2
24
25
Disable clock
Enable display
Enable out
Carry output
Reset
Not-2 output
To segment c
To segment f
To segment g
Clock input
To segment b
To segment e
To segment a
To segment d
3
4
1
2
16
15
14
13
6
8
7
12
11
9
10
5
4026
Counter
Figure 4-36. The 4026 decade counter is a CMOS chip that accepts
clock pulses on pin 1, maintains a running total from 0 to 9, and out-
puts this total via pins designed to interface with a seven-segment
LED numeric display.

Chips, Ahoy! 173
Fundamentals
Counters and seven-segment displays
Most counters accept a stream of pulses and distribute
them to a series of pins in sequence. The 4026 decade
counter is unusual in that it applies power to its output pins
in a pattern that is just right to illuminate the segments of a
7-segment numeric display.
Some counters create positive outputs (they“source”
current) while others create negative outputs (they“sink”
current). Some seven-segment displays require positive
input to light up the numbers. These are known as“common
cathode”displays. Others require negative input and are
known as“common anode”displays. The 4026 delivers posi-
tive outputs and requires a common cathode display.
Check the data sheet for any counter chip to find out how
much power it requires, and how much it can deliver. CMOS
chips are becoming dated, but they are very useful to hob-
byists, because they will tolerate a wide range of supply
voltage—from 5 to 15 volts in the case of the 4026. Other
types of chips are much more limited.
Most counters can source or sink only a few milliamps of
output power. When the 4026 is running on a 9-volt power
supply, it can source about 4mA of power from each pin.
This is barely enough to drive a seven-segment display.
You can insert a series resistor between each output pin of
the counter and each input pin of the numeric display, but
a simpler, quicker option is to use just one series resistor
for each numeral, between the negative-power pin and
ground. The experiment that I’m describing uses this short-
cut. Its disadvantage is that digits that require only a couple
of segments (such as numeral 1) will appear brighter than
those that use many segments (such as numeral 8).
If you want your display to look bright and professional,
you really need a transistor to drive each segment of each
numeral. An alternative is to use a chip containing multiple
“op amps”to amplify the current.
When a decade counter reaches 9 and rolls over to 0, it
emits a pulse from its“carry”pin. This can drive another
counter that will keep track of tens. The carry pin on that
counter can be chained to a third counter that keeps track
of hundreds, and so on. In addition to decade counters,
there are hexadecimal counters (which count in 16s), octal
counters (in 8s), and so on.
Why would you need to count in anything other than tens?
Consider that the four numerals on a digital clock each count
differently. The rightmost digit rolls over when it reaches
10. The next digit to the left counts in sixes. The first hours
digit counts to 10, gives a carry signal, counts to 2, and gives
another carry signal. The leftmost hours digit is either blank
or 1, when displaying time in 12-hour format. Naturally there
are counters specifically designed to do all this.
Counters have control pins such as“clock disable,”which
tells the counter to ignore its input pulses and freeze the
display,“enable display,”which enables the output from the
chip, and“reset,”which resets the count to zero.
The 4026 requires a positive input to activate each control pin.
When the pins are grounded, their features are suppressed.
To make the 4026 count and display its running total you
must ground the“clock disable”and“reset”pins (to suppress
their function) and apply positive voltage to the“enable
display”pin (to activate the output). See Figure 4-36 to see
these pins identified.
Assuming that you succeed in getting your counter to drive the numeric dis-
play, you’re ready to add two more counters, which will control the remaining
two numerals. The first counter will count in ones, the second in tens, and the
third in hundreds.
In Figure 4-37, I’ve continued to use arrows and numbers to tell you which pins
of the counters should be connected to which pins of the numeric display. Oth-
erwise, the schematic would be a confusing tangle of wires crossing each other.
At this point, you can give up in dismay at the number of connections—but
really, using a breadboard, it shouldn’t take you more than half an hour to
complete this phase of the project. I suggest you give it a try, because there’s

Chapter 4174
something magical about seeing a display count from 000 through 999“all by
itself,”and I chose this project because it also has a lot of instructional value.
S1 is attached to the“clock disable”pin of IC1, so that when you hold down this
button, it should stop that counter from counting. Because IC1 controls IC2,
and IC2 controls IC3, if you freeze IC1, the other two will have to wait for it to
resume. Therefore you won’t need to make use of their“clock disable”features.
S2 is connected to the“reset”pins of all three counters, so that when you hold
down this button, it should set them all to zero.
S3 sends positive pulses manually to the“clock input”pin of the first counter.
S1, S2, and S3 are all wired in parallel with 1K resistors connected to the nega-
tive side of the power supply. The idea is that when the buttons are not being
pressed, the“pull-down”resistors keep the pins near ground (zero) voltage.When
you press one of the buttons, it connects positive voltage directly to the chip,
and easily overwhelms the negative voltage. This way, the pins remain either in
a definitely positive or definitely negative state. If you disconnect one of these
pull-down resistors you are likely to see the numeric display “flutter” erratically.
(The numeric display chip has some unconnected pins, but this won’t cause any
problem, because it is a passive chip that is just a collection of LED segments.)
Always connect input pins of a CMOS chip so that they are either positive or nega-
tive. See the “No Floating Pins” warning on the next page.
I suggest that you connect all the wires shown in the schematic first. Then cut
lengths of 22-gauge wire to join the remaining pins of the sockets from IC1,
IC2, and IC3 to IC4.
Switch on the power and press S2.You’ll see three zeros in your numeric display.
Each time you press S3, the count should advance by 1. If you press S2, the
count should reset to three zeros. If you hold down S1 while you press S3 re-
peatedly, the counters should remain frozen, ignoring the pulses from S3.
Fundamentals
Switch bounce
When you hit S3, I think you’ll find that the count sometimes increases by more
than 1.This does not mean that there’s something wrong with your circuit or your
components; you are just observing a phenomenon known as“switch bounce.”
On a microscopic level, the contacts inside a pushbutton switch do not close
smoothly, firmly, and decisively.They vibrate for a few microseconds before set-
tling; the counter chip detects this vibration as a series of pulses, not just one.
Various circuits are available to“debounce”a switch. The simplest option is to
put a small capacitor in parallel with the switch, to absorb the fluctuations; but
this is less than ideal. I’ll come back to the topic of debouncing later in the book.
Switch bounce is not a concern in this circuit, because we’re about to get rid of
S3 and substitute a 555 timer that generates nice clean bounceless pulses.
1
2
3
4
5
6
7
8
13
16
15
14
13
17
12
11
10
9
1
2
3
4
5
6
7
8
16
15
14
13
12
11
10
9
1
2
3
4
5
6
7
8
16
15
14
13
12
11
10
9
1
2
3
4
5
6
7
8
9
10
11
12
13
14
28
27
26
25
24
23
22
21
20
19
18
17
16
15
IC1
IC2
IC3
IC4
S1
S3
R1
R2
R4
R5
R6
R3
S2
C1
23
22
27
28
12
15
10
16
11
8
20
21
7
4
1
2
24
25
6
Figure 4-37. This test circuit, laid out as you
would be likely to place it on a breadboard,
allows you to trigger a counter manually
to verify that the display increments from
000 upward to 999.
Component values:
All resistors are 1K.
S1, S2, S3: SPST tactile switches, normally
open
IC1, IC2, IC3: 4026 decade counter chips
IC4: Kingbright 3-digit common-cathode
display
C1: 100 µF (minimum) smoothing capacitor
Wire the output pins on IC1, IC2, and IC3
to the pins on IC4, according to the num-
bers preceded by arrows. The actual wires
have been omitted for clarity. Check for
the pinouts of IC4.

Chips, Ahoy! 175
Pulse Generation
A 555 timer is ideal for driving a counter chip. You’ve already seen how to wire
a 555 to create a stream of pulses that made noise through a loudspeaker. I’m
reproducing the same circuit in Figure 4-38 in simplified form, using the posi-
tive and negative supply configuration in the current project. Also I’m show-
ing the connection between pins 2 and 6 in the way that you’re most likely to
make it, via a wire that loops over the top of the chip.
For the current experiment, I’m suggesting initial component values that will
generate only four pulses per second. Any faster than that, and you won’t be
able to verify that your counters are counting properly.
Install IC5 and its associated components on your breadboard immediately
above IC1. Don’t leave any gap between the chips. Disconnect S3 and R3 and
connect a wire directly between pin 3 (output) of IC5 and pin 1 (clock) of IC1,
the topmost counter. Power up again, and you should see the digits advancing
rapidly in a smooth, regular fashion. Press S1, and while you hold it, the count
should freeze. Release S1 and the count will resume. Press S2 and the counter
should reset, even if you are pressing S1 at the same time.
1
2
3
4 5
6
7
8
IC5
R7
R8
C2C3
To Pin 1
of 4026
Counter
IC1
Figure 4-38. A basic astable circuit to drive the decade counter in the previous schematic.
Output is approximately 4 pulses per second.
R7: 1K
R8: 2K2
C2: 68 µF
C3: 0.1 µF
IC5: 555 timer
No Floating Pins!
A CMOS chip is hypersensitive. Any
pin that is not wired either to the
supply voltage or to ground is said
to be “floating” and may act like an
antenna, sensitive to the smallest
fluctuations in the world around it.
The 4026 counter chip has a pin
labeled “clock disable.” The manu-
facturer’s data sheet helpfully tells
you that if you give this pin a positive
voltage, the chip stops counting and
freezes its display. As you don’t want
to do that, you may just ignore that
pin and leave it unconnected, at least
while you test the chip. This is a very
bad idea!
What the data sheet doesn’t bother
to tell you (presumably because
“everyone knows” such things) is that
if you want the clock to run normally,
the clock-disable feature itself has to
be disabled, by wiring it to negative
(ground) voltage. If you leave the pin
floating (and I speak from experi-
ence), the chip will behave erratically
and uselessly.
All input pins must be either
positively or negatively wired, unless
otherwise specified.

Chapter 4176
Refinements
Now it’s time to remember that what we really want this circuit to do is test a
person’s reflexes. When the user starts it, we want an initial delay, followed by a
signal—probablyanLEDthatcomeson.Theuserrespondstothesignalbypress-
ing a button as quickly as possible. During the time it takes for the person to re-
spond, the counter will count milliseconds.When the person presses the button,
the counter will stop.The display then remains frozen indefinitely, displaying the
number of pulses that were counted before the person was able to react.
How to arrange this? I think we need a flip-flop. When the flip-flop gets a sig-
nal, it starts the counter running—and keeps it running. When the flip-flop
gets another signal (from the user pressing a button), it stops the counter run-
ning, and keeps it stopped.
How do we build this flip-flop? Believe it or not, we can use yet another 555
timer, in a new manner known as bistable mode.
Fundamentals
The bistable 555 timer
Figure 4-39 shows the internal layout of a 555 timer, as
before, but the external components on the righthand side
have been eliminated. Instead, I’m applying a constant
negative voltage to pin 6. Can you see the consequences?
Suppose you apply a negative pulse to the trigger (pin 2).
Normally when you do this and the 555 starts running, it
generates a positive output while charging a capacitor at-
tached to pin 6. When the capacitor reaches 2/3 of the full
supply voltage, this tells the 555 to ends its positive output,
and it flips back to negative.
Well, if there’s no capacitor, there’s nothing to stop the timer.
Its positive output will just continue indefinitely. However,
pin 4 (the reset) can still override everything, so if you apply
negative voltage to pin 4, it flips the output to negative.
After that, the output will stay negative indefinitely, as it
usually does, until you trigger the timer by dropping the
voltage to pin 2 again. This will flip the timer back to gener-
ating its positive output.
Here’s a quick summary of the bistable configuration:
• A negative pulse to pin 2 turns the output positive.
• A negative pulse to pin 4 turns the output negative.
• The timer is stable in each of these states. Its run-time
has become infinite.
It’s OK to leave pins 5 and 7 of the timer unconnected,
because we’re pushing it into extreme states where any
random signals from those pins will be ignored.
1
2
3
4 5
6
7
FF
8
A
B
Figure 4-39. In the bistable configuration, pin 6 of a 555 timer
is perpetually negative, so the timer cycle never ends, unless
you force it to do so by applying a negative pulse to pin 4 (the
reset).

Chips, Ahoy! 177
In bistable mode, the 555 has turned into one big flip-flop. To avoid any un-
certainty, we keep pins 2 and 4 normally positive via pull-up resistors, but
negative pulses on those pins can overwhelm them when we want to flip the
555 into its opposite state. The schematic for running a 555 timer in bistable
mode, controlled by two pushbuttons, is shown in Figure 4-40. You can add
this above your existing circuit. Because you’re going to attach the output
from IC6 to pin 2 of IC1, the topmost counter, you can disconnect S1 and R1
from that pin. See Figure 4-41.
Now, power up the circuit again.You should find that it counts in the same way
as before, but when you press S4, it freezes. This is because your bistable 555
timer is sending its positive output to the “clock disable” pin on the counter.
The counter is still receiving a stream of pulses from the astable 555 timer,
but as long as pin 2 is positive on the counter, the counter simply ignores the
pulses.
Now press S5, which flips your bistable 555 back to delivering a negative out-
put, at which point the count resumes.
We’re getting close to a final working circuit here. We can reset the count to
zero (with S3), start the count (with S5), and wait for the user to stop the count
(with S4). The only thing missing is a way to start the count unexpectedly.
To Pin 2
of 4026
Counter
IC1
1
2
3
4 5
6
7
8
IC6
S4
R9
R10
S5
Figure 4-40. Adding a bistable 555 timer to the reflex tester will stop the counter with a
touch of a button, and keep it stopped.
R9, R10: 1K
IC6: 555 timer

Chapter 4178
The Delay
Suppose we set up yet another 555 in monostable mode. Trigger its pin 2 with
a negative pulse, and the timer delivers a positive output that lasts for, say, 4
seconds. At the end of that time, its output goes back to being negative. Maybe
we can hook that positive-to-negative transition to pin 4 of IC6. We can use this
instead of switch S5, which you were pressing previously to start the count.
Check the new schematic in Figure 4-41 which adds another 555 timer, IC7
above IC6. When the output from IC7 goes from positive to negative, it will
trigger the reset of IC6, flipping its output negative, which allows the count to
begin. So IC7 has taken the place of the start switch, S4. You can get rid of S4,
but keep the pull-up resistor, R9, so that the reset of IC6 remains positive the
rest of the time.
This arrangement works because I have used a capacitor, C4, to connect the
output of IC7 to the reset of IC6. The capacitor communicates the sudden
change from positive to negative, but the rest of the time it blocks the steady
voltage from IC7 so that it won’t interfere with IC6.
The final schematic in Figure 4-41 shows the three 555 timers all linked together,
as you should insert them above the topmost counter, IC1. I also added an LED to
signal the user. Figure 4-42 is a photograph of my working model of the circuit.
Figure 4-42. The complete reaction-timer circuit barely fits on a 63-row breadboard.
Because this circuit is complicated, I’ll summarize the sequence of events
when it’s working. Refer to Figure 4-41 while following these steps:
1. User presses Start Delay button S4, which triggers IC7.
2. IC7 output goes high for a few seconds while C5 charges.
3. IC7 output drops back low.
4. IC7 communicates a pulse of low voltage through C4 to IC6, pin 4.
5. IC 6 output flips to low and flops there.
6. Low output from IC6 sinks current through LED and lights it.
7. Low output from IC6 also goes to pin 2 of IC1.
1
2
3
16
15
14
1
2
3
4 5
6
7
8
IC5
IC1
1
2
3
4 5
6
7
8
IC6
1
2
3
4 5
6
7
8
IC7
Start Delay
Stop Count
Reset
Set to Zero
Prompt
LED
Disable
Clock
Clock
Input
R7
R8
C2
C5
C1
C3
C4
C6
S3
S2
S4
R9
R10
R11
R12
R10
Figure 4-41. The completed control section
of the circuit, to be added above these
timers.
R7, R9, R10, R12: 1K
R8: 2K2
R11: 330K
C1: 100 µF
C2: 68 µF
C3, C4, C6: 0.1 µF
C5: 10 µF
S1, S2, S3: tactile switches
IC5, IC6, IC7: 555 timers

Chips, Ahoy! 179
8. Low voltage on pin 2 of IC1 allows IC1 to start counting.
9. User presses S3, the“stop”button.
10. S3 connects pin 2 of IC6 to ground.
11. IC6 output flips to high and flops there.
12. High output from IC6 turns off the LED.
13. High output from IC6 also goes to pin 2 of IC1.
14. High voltage on pin 2 of IC1 stops it from counting.
15. After assessing the result, user presses S2.
16. S2 applies positive voltage to pin 15 of IC1, IC2, IC3.
17. Positive voltage resets counters to zero.
18. The user can now try again.
19. Meanwhile, IC5 is running continuously throughout.
In case you find a block diagram easier to understand, I’ve included that, too,
in Figure 4-43.
Using the Reflex Tester
At this point, you should be able to test the circuit fully. When you first switch
it on, it will start counting, which is slightly annoying, but easily fixed. Press S3
to stop the count. Press S2 to reset to zero.
Now press S4. Nothing seems to happen—but that’s the whole idea.The delay
cycle has begun in stealth mode. After a few seconds, the delay cycle ends,
and the LED lights up. Simultaneously, the count begins. As quickly as pos-
sible, the user presses S3 to stop the count.The numerals freeze, showing how
much time elapsed.
There’s only one problem—the system has not yet been calibrated. It is still
running in slow-motion mode. You need to change the resistor and capacitor
attached to IC5 to make it generate 1,000 pulses per second instead of just
three or four.
Substitute a 10K trimmer potentiometer for R8 and a 1 µF capacitor for C2.
This combination will generate about 690 pulses per second when the trim-
mer is presenting maximum resistance. When you turn the trimmer down to
decrease its resistance, somewhere around its halfway mark the timer will be
running at 1,000 pulses per second.
How will you know exactly where this point is? Ideally, you would attach an
oscilloscope probe to the output from IC5. But, most likely, you don’t have an
oscilloscope, so here are a couple other suggestions.
Start
Switch
Stop
Switch
Reset
Switch
Numeric
Display
Prompt
LED
555 in
Delay
Mode
End-of-Delay
Start Signal
555 in
Flip-Flop
Mode
555
pulse
generator
Counter
Enable
or
Disable
Pulse
Counter
Figure 4-43. The functions of the reflex
tester, summarized as a block diagram.

Chapter 4180
First remove the 1 µF capacitor at C2 and substitute a 10 µF capacitor. Because
you are multiplying the capacitance by 10, you will reduce the speed by 10.
The leftmost digit in your display should now count in seconds, reaching 9 and
rolling over to 0 every 10 seconds.You can adjust your trimmer potentiometer
while timing the display with a stopwatch. When you have it right, remove the
10 µF capacitor and replace the 1 µF capacitor at C2.
The only problem is, the values of capacitors may be off by as much as 10%. If
you want to fine-tune your reflex timer, you can proceed as follows.
Disconnect the wire from pin 5 of IC3, and substitute an LED with a 1K series
resistor between pin 5 and ground. Pin 5 is the “carry” pin, which will emit a
positive pulse whenever IC3 counts up to 9 and rolls over to start at 0 again.
Because IC3 is counting tenths of a second, you want its carry output to occur
once per second.
Now run the circuit for a full minute, using your stopwatch to see if the flashing
LED drifts gradually faster or slower than once per second. If you have a camcord-
er that has a time display in its viewfinder, you can use that to observe the LED.
If the LED flashes too briefly to be easily visible, you can run a wire from pin 5 to
another 555 timer that is set up in monostable mode to create an output lasting
for around 1/10 of a second. The output from that timer can drive an LED.
Enhancements
It goes without saying that anytime you finish a project, you see some oppor-
tunities to improve it. Here are some suggestions:
1. No counting at power-up. It would be nice if the circuit begins in its
“ready” state, rather than already counting. To achieve this you need to
send a negative pulse to pin 2 of IC6, and maybe a positive pulse to pin 15
of IC1. Maybe an extra 555 timer could do this. I’m going to leave you to
experiment with it.
2. Audible feedback when pressing the Start button. Currently, there’s no
confirmation that the Start button has done anything. All you need to do
is buy a piezoelectric beeper and wire it between the righthand side of
the Start button and the positive side of the power supply.
3. A random delay interval before the count begins. Making electronic com-
ponents behave randomly is very difficult, but one way to do it would be
to require the user to hold his finger on a couple of metal contacts. The
skin resistance of the finger would substitute for R11. Because the finger
pressure would not be exactly the same each time, the delay would vary.
You’d have to adjust the value of C5.

Chips, Ahoy! 181
Summing Up
This project demonstrated how a counter chip can be controlled, how counter
chips can be chained together, and three different functions for 555 timers. It
also showed you how chips can communicate with each other, and introduced
you to the business of calibrating a circuit after you’ve finished building it.
Naturally, if you want to get some practical use from the circuit, you should
build it into an enclosure with heavier-duty pushbuttons—especially the but-
ton that stops the count. You’ll find that when people’s reflexes are being test-
ed, they are liable to hit the stop button quite hard.
Because this was a major project, I’ll follow it up here with some quicker, easier
ones as we move into the fascinating world of another kind of integrated circuit:
logic chips.
You will need:
• Assorted resistors and capacitors.
• 74HC00 quad 2-input NAND chip, 74HC08 quad 2-input AND chip, and
LM7805 voltage regulator. Quantity: 1 of each.
• Signal diode, 1N4148 or similar. Quantity: 1.
• Low-current LED. Quantity: 1.
You’re going to be entering the realm of pure digital electronics, using “logic
gates” that are fundamental in every electronic computing device. When you
deal with them individually, they’re extremely easy to understand. When you
start chaining them together, they can seem intimidatingly complex. So let’s
start with them one at a time.
Logic gates are much fussier than the 555 timer or the 4026 counter that you
used previously. They demand an absolutely precise 5 volts DC, with no fluc-
tuations or “spikes” in the flow of current. Fortunately, this is easy to achieve:
just set up your breadboard with an LM7805 voltage regulator, as shown in
the schematic in Figure 4-44 and the photograph in Figure 4-45. The regula-
tor receives 9 volts from your usual voltage supply, and reduces it to 5 volts,
with the help of a couple of capacitors. You apply the 9 volts to the regulator,
and distribute the 5 volts down the sides of your breadboard instead of the
unregulated voltage that you used previously. Use your meter to verify the
voltage, and make sure you have the polarity clearly marked.
After installing your regulator, take a couple of tactile switches, two 10K resis-
tors, a low-current LED, and a 1K resistor, and set them around a 74HC00 logic
chip as shown in Figure 4-46. You may notice that many of the pins of the chip
are shorted together and connected to the negative side of the power supply.
I’ll explain that in a moment.
LM7805
0.33uF
9v DC
5v DC
0.1uF
Figure 4-44. This simple circuit is essential
to provide a regulated 5V DC supply for
logic chips.
Figure 4-45. The voltage regulator and its
two capacitors can fit snugly at the top of
a breadboard. Remember to apply the 9V
input voltage at the left pin of the regula-
tor, and distribute the 5V output down the
sides of the breadboard.

Chapter 4182
10K
10K
1K
74HC00
NAND
gate
LM7805
0.33uF
0.1uF
9v DC
Figure 4-46. By observing the LED when you press either, both, or neither of the buttons,
you can easily figure out the logical function of the NAND gate.
When you connect power, the LED should light up. Press one of the tactile
switches, and the LED remains illuminated. Press the other tactile switch, and
again the LED stays on. Now press both switches, and the light should go out.
Pins 1 and 2 are logic inputs for the 74HC00 chip. Initially they were held at
negative voltage, being connected to the negative side of the power supply
through 10K resistors. But each pushbutton overrides its pull-down resistor
and forces the input pin to go positive.
The logic output from the chip, as you saw, is normally positive—but not if
the first input and the second input are positive. Because the chip does a“Not
AND”operation, it’s known as a NAND logic gate. You can see the breadboard
layout in Figure 4-47. Figure 4-48 is a simplified version of the circuit. The U-
shaped thing with a circle at the bottom is the logic symbol for a NAND gate.
No power supply is shown for it, but in fact all logic chips require a power sup-
ply, which enables them to put out more current than they take in. Anytime
you see a symbol for a logic chip, try to remember that it has to have power
to function.
Fundamentals
Voltage regulators
The simplest versions of these
little semiconductors accept a
higher DC voltage on one pin
and deliver a lower DC voltage
on another pin, with a third pin
(usually in the middle) serving as
a common negative, or ground.
You should also attach a couple of
capacitors to smooth the current,
as shown in Figure 4-46.
Typically you can put a 7.5-volt or
9-volt supply on the“input”side of
a 5-volt regular, and draw a precise
5 volts from the“output”side. If
you’re wondering where the extra
voltage goes, the answer is, the
regulator turns the electricity into
heat. For this reason, small regula-
tors (such as the one in Figure 4-8)
often have a metal back with a
hole in the top. Its purpose is to
radiate heat, which it will do more
effectively if you bolt it to a piece
of aluminum, since aluminum
conducts heat very effectively. The
aluminum is known as a heat sink,
and you can buy fancy ones that
have multiple cooling fins.
For our purposes, we won’t be
drawing enough current to require
a heat sink.
Figure 4-47. This breadboard layout is
exactly equivalent to the schematic in
Figure 4-46.

Chips, Ahoy! 183
The 74HC00 actually contains four NAND gates, each with two logical inputs
and one output. They are arrayed as shown in Figure 4-49. Because only one
gate was needed for the simple test, the input pins of the unused gates were
shorted to the negative side of the power supply.
Pin 14 supplies positive power for the chip; pin 7 is its ground pin. Almost
all the 7400 family of logic chips use the same pins for positive and negative
power, so you can swap them easily.
In fact, let’s do that right now. First, disconnect the power. Carefully pull out
the 74HC00 and put it away with its legs embedded in conductive foam. Sub-
stitute a 74HC08 chip, which is an AND chip. Make sure you have it the right
way up, with its notch at the top. Reconnect the power and use the pushbut-
tons as you did before. This time, you should find that the LED comes on if
the first input AND the second input are both positive, but it remains dark
otherwise. Thus, the AND chip functions exactly opposite to the NAND chip.
Its pinouts are shown in Figure 4-50.
You may be wondering why these things are useful. Soon you’ll see that we
can put logic gates together to do things such as create an electronic com-
bination lock, or a pair of electronic dice, or a computerized version of a TV
quiz show where users compete to answer a question. And if you were really
insanely ambitious, you could build an entire computer out of logic gates.
7400
Quad
2-Input
NAND gate
3
4
1
2
14
13
12
11
6
7
10
9
8
5
Figure 4-49. The pinouts of the logic gates in a 74HC00chip.
7408
Quad
2-Input
AND gate
3
4
1
2
14
13
12
11
6
7
10
9
8
5
Figure 4-50. The pinouts of the logic gates in a 74HC08chip.
Figure 4-48. The structure and function of
the NAND gate is easier to visualize with
this simplified schematic that omits the
power supply for the chip and doesn’t
attempt to place the wires to fit a bread-
board layout.

Chapter 4184
Background
From Boole to Shannon
George Boole was a British mathematician, born in 1815, who did something
that few people are ever lucky enough or smart enough to do: he invented an
entirely new branch of mathematics.
Interestingly, it was not based on numbers. Boole had a relentlessly logical
mind, and he wanted to reduce the world to a series of true-or-false statements
which could overlap in interesting ways. For instance, suppose there is a couple
named Ann and Bob who have so little money, they only own one hat. Clearly,
if you happen to run into Ann and Bob walking down the street, there are four
possibilities: neither of them may be wearing a hat, Ann may be wearing it, or
Bob may be wearing it, but they cannot both be wearing it.
The diagram in Figure 4-51 illustrates this. All the states are possible except the
one where the circles overlap. (This is known as a Venn diagram. I leave it to you
to search for this term if it interests you and you’d like to learn more.) Boole took
this concept much further, and showed how to create and simplify extremely
complex arrays of logic.
No one
wears
the hat
Ann wears
the hat
Bob wears
the hat
Both
wear the
hat
Figure 4-51. This slightly frivolous Venn diagram illustrates the various possibilities
for two people, Ann and Bob, who own only one hat.
Another way to summarize the hat-wearing situation is to make the“truth table”
shown in Figure 4-52. The rightmost column shows whether each combination
of propositions can be true. Now check the table in Figure 4-53. It’s the same
table but uses different labels, which describe the pattern you have seen while
using the NAND gate.
Boole published his treatise on logic in 1854, long before it could be applied
to electrical or electronic devices. In fact, during his lifetime, his work seemed
to have no practical applications at all. But a man named Claude Shannon
encountered Boolean logic while studying at MIT in the 1930s, and in 1938 he
published a paper describing how Boolean analysis could be applied to circuits
using relays. This had immediate practical applications, as telephone networks
were growing rapidly, creating complicated switching problems.

Chips, Ahoy! 185
Background
From Boole to Shannon (continued)
Ann is
wearing
the hat
Bob is
wearing
the hat
This
combination
can be
YES
YES
YES
NO
NO NO
YES
NO
TRUE
TRUE
FALSE
TRUE
Figure 4-52. The hat-wearing possibilities can be expressed in a
“truth table.”
Input A Input B Output
ON
ON
ON
OFF
OFF OFF
ON
OFF
ON
ON
OFF
ON
Figure 4-53. The truth-table from can be relabeled to describe
the inputs and outputs of a NAND gate.
A very simple telephone problem could be expressed like
this. Suppose two customers in a rural area share one tele-
phone line. If one of them wants to use the line, or the other
wants to use it, or neither of them wants to use it, there’s
no problem. But they cannot both use it at once. You may
notice that this is exactly the same as the hat-wearing situa-
tion for Ann and Bob.
We can easily draw a circuit using two normally closed
relays that creates the desired outcome (see Figure 4-54),
but if you imagine a telephone exchange serving many
thousands of customers, the situation becomes very compli-
cated indeed. In fact, in Shannon’s time, no logical process
existed to find the best solution and verify that it used fewer
components than some other solution.
Shannon saw that Boolean analysis could be used for this
purpose. Also, if you used an“on”condition to represent
numeral 1 and an“off”condition to represent numeral 0,
you could build a system of relays that could count. And if it
could count, it could do arithmetic.
When vacuum tubes were substituted for relays, the first
practical digital computers were built. Transistors took the
place of vacuum tubes, and integrated circuit chips replaced
transistors, leading to the desktop computers that we now
take for granted today. But deep down, at the lowest levels
of these incredibly complex devices, they still use the laws
of logic discovered by George Boole. Today, when you use
a search engine online, if you use the words AND and OR to
refine your search, you’re actually using Boolean operators.
Output
Input BInput A
Figure 4-54. This relay circuit could illustrate the desired logic for two telephone customers wanting to share one line, and its
behavior is almost identical to that of the NAND schematic shown in Figure 4-48.

Chapter 4186
Essentials
Logic gate basics
The NAND gate is the most fundamental building block of digital computers,
because (for reasons which I don’t have space to explain here) it enables digital
addition. If you want to explore more try searching online for topics such as
“binary arithmetic”and“half-adder.”
Generally, there are seven types of logic gates:
• AND
• NAND
• OR
• NOR
• XOR
• XNOR
• NOT
Of the six two-input gates, the XNOR is hardly ever used. The NOT gate has a
single input, and simply gives a negative output when the input is positive or a
positive output when the input is negative. The NOT is more often referred to as
an“Inverter.”The symbols for all seven gates are shown in Figure 4-56.
INVERTER
AND NAND OR XOR
NOT
Logical Inputs
Logical Outputs
XNORNOR
Figure 4-56. American symbols for the six types of two-input logic gates, and the
single-input inverter.
I’ve shown the American symbols.
Other symbols have been adopted in
Europe, but the traditional symbols
shown here are the ones that you will
usually find, even being used by Eu-
ropeans. I also show the truth tables,
in Figure 4-57, illustrating the logical
output (high or low) for each pair of
inputs of each type of gate.
Figure 4-55. Ann and Bob attempt to over-
come the limitations of Boolean logic.
Figure 4-57. Inputs and corresponding outputs for the six types of logic gates (note
that the XNOR gate is seldom used). The minus signs indicate low voltage, close
to ground potential. The plus signs indicate higher voltage, close to the positive
potential of the power supply in the circuit. The exact voltages will vary depending
on other components that may be actively connected.

Chips, Ahoy! 187
Essentials
Logic gate basics (continued)
If you have difficulty visualizing logic gates, a mechanical comparison may
help. You can think of them as being like sliding plates with holes in them, in a
bubblegum machine. Two people, A and B, can push the plates. These people
are the two inputs, which are considered positive when they are doing some-
thing. (Negative logic systems also exist, but are uncommon, so I’m only going
to talk about positive systems here.)
The flow of bubblegum represents a flow of positive current. The full set of pos-
sibilities is shown in Figures 4-58 through 4-63.
B
AND
B
A
AA
A
B B
NONO NO
NONO YES
NONOYES
YESYES YES
INPUTA
INPUTB
OUTPUT
Figure 4-58
YESNO NO
YESNO YES
YESNOYES
NOYES YES
INPUTA
INPUTB
OUTPUT
NAND
BB
A B AB
A A
Figure 4-59

Chapter 4188
Essentials
B
A
B
OR
A
A A
BB
NONO NO
YESNO YES
YESNOYES
YESYES YES
INPUTA
INPUTB
OUTPUT
Figure 4-60
NOR
A
A
A
A
B
B
B B
YESNO NO
NONO YES
NONOYES
NOYES YES
INPUTA
INPUTB
OUTPUT
Figure 4-61

Chips, Ahoy! 189
Essentials
B A
B
A
XOR
A
A
B
B
NONO NO
YESNO YES
YESNOYES
NOYES YES
INPUTA
INPUTB
OUTPUTFigure 4-62
A
B A B
XNOR
B BA
A
YESNO NO
NONO YES
NONOYES
YESYES YES
INPUTA
INPUTB
OUTPUT
Figure 4-63

Chapter 4190
Background
The confusing world of TTL and CMOS
Back in the 1960s, the first logic gates were built with
Transistor-Transistor Logic, abbreviatedTTL, meaning that tiny
bipolar transistors were etched into a single wafer of silicon.
Soon, these were followed by Complementary Metal Oxide
Semiconductors, abbreviated CMOS. Each of these chips was
a collection of metal-oxide field-effect transistors (known as
MOSFETs).The 4026 chip that you used earlier is an old CMOS.
You may remember that bipolar transistors amplify current.
TTL circuits are similar: they are sensitive to current, rather
than voltage.Thus they require a significant flow of electricity,
to function. But CMOS chips are like the programmable uni-
junction transistor that I featured previously.They are voltage-
sensitive, enabling them to draw hardly any current while they
are waiting for a signal, or pausing after emitting a signal.
The two families named TTL and CMOS still exist today. The
table in Figure 4-64 summarizes their basic advantages and
disadvantages. The CMOS series, with part numbers from
4000 upward, were easily damaged by static electricity but
were valuable because of their meager power consumption.
The TTL series, with part numbers from 7400 upward, used
much more power but were less sensitive and very fast. So,
if you wanted to build a computer, you used the TTL family,
but if you wanted to build a little gizmo that would run for
weeks on a small battery, you used the CMOS family.
From this point on everything became extremely confusing,
because CMOS manufacturers wanted to grab market share
by emulating the advantages of TTL chips. Newer genera-
tions of CMOS chips even changed their part numbers to
begin with“74”to emphasize their compatibility, and the
functions of pins on CMOS chips were swapped around to
match the functions of pins on TTL chips. Consequently, the
pinouts of CMOS and TTL chips are usually now identical,
but the meaning of“high”and“low”states changed in each
new generation, and the maximum supply voltages for CMOS
chips were revised downward. Note I have included question
marks beside two categories in the CMOS column, as modern
CMOS chips have overcome those disadvantages—at least to
some extent.
Here’s a quick summary, which will be useful to you if you
look at a circuit that you find online, and you wonder about
the chips that have been specified.
Where you see a letter“x,”it means that various numbers
may appear in that location. Thus“74xx”includes the 7400
NAND gate, the 7402 NOR gate, the 74150 16-bit data selec-
tor, and so on. A combination of letters preceding the“74”
identifies the chip manufacturer, while letters following the
part number may identify the style of package, may indicate
whether it contains heavy metals that are environmentally
toxic, and other details.
TTL CMOS
Speed Faster Slower?
More?
Vulnerable
to static
electricity
Less
Part
number
series
7400 4000
(Later adopted
7400 numbering)
????
Power
Supply Range
Narrow
5v
Wider
3v-6v
Power
Consumption Higher Very Low
Input
Impedance Low Very High
Figure 4-64. The basic differences between the two families of
logic chips. In successive generations, these differences have
gradually diminished.
TTL family:
74xx
The old original generation, now obsolete.
74Sxx
Higher speed“Schottky”series, now obsolete.
74LSxx
Lower power Schottky series, still used occasionally.
74ALSxx
Advanced low-power Schottky.
74Fxx
Faster than the ALS series.

Chips, Ahoy! 191
Background
The confusing world of TTL and CMOS (continued)
CMOS family:
40xx
The old original generation, now obsolete.
40xxB
The 4000B series was improved but still susceptible to
damage from static electricity. Many hobby circuits still
use these chips because they will run from relatively
high voltages and can power LEDs and even small
relays directly.
74HCxx
Higher-speed CMOS, with part numbers matching the
TTL family, and pinouts matching the TTL family, but
input and output voltages not quite the same as the
TTL family. I’ve used this generation extensively in this
book, because it’s widely available, and the circuits
here have no need for greater speed or power.
74HCTxx
Like the HC series but matching the TTL voltages.
74ACxx
Advanced version of HC series. Faster, with higher
output capacity.
74ACTxx
Like the AC series but with the same pin functions and
voltages as TTL.
74AHCxx
Advanced higher-speed CMOS.
74AHCTxx
Like the AHC series but with the same pin functions
and voltages as TTL.
74LVxx
Lower voltage (3.3v) versions, including LV, LVC, LVT,
and ALVC series.
As you can see, these days you have to interpret part num-
bers very carefully. But which family and generation of chips
should you use? Well, that depends! Following are some
guidelines.
What you don’t need:
1. Speed differences are irrelevant from our point of view,
as we’re not going to be building circuits running at
millions of cycles per second.
2. Price differences are so small as to be inconsequential.
3. Lower-voltage (LV) CMOS chips are not very interesting
for our small experimental circuits.
4. Try to avoid mixing different families, and different
generations of the same family, in the same circuit.
They may not be compatible.
5. Some modern chip varieties may be only available in
the surface-mount package format. Because they’re so
much more difficult to deal with, and their only major
advantage is miniaturization, I don’t recommend them.
6. In the TTL family, the LS and ALS series cannot handle
as much output current as the S series and the F series.
You don’t need them.
What you should use:
1. The old 74LSxx series of TTL chips was so popular,
you’ll still find schematics that specify these chips. You
should still be able to buy them from sources online,
but if not, you can substitute the 74HCTxx chips, which
are designed to function identically.
2. The old 4000B series of CMOS chips are still used by
hobbyists because their willingness to tolerate high
voltages is convenient. While TTL or TTL-compatible
chips require a carefully regulated 5 volts, the 4000B
chips would handle 15 volts—and also delivered
enough power to energize LEDs or even very small re-
lays. Some hobbyists also have a nostalgic affection for
the 74Cxx series of chips, which had the same pin con-
nections as the TTL chips but could still tolerate higher
voltages and higher output current. The trouble is,
some of the 74Cxx chips are almost extinct, and while
the 4000B chips are still available, they are considered
almost obsolete.

Chapter 4192
Background
The confusing world of TTL and CMOS (continued)
Bottom line: I suggest you use the 4000B chips only if you want to replicate an
old circuit, or if a modern equivalent is unavailable (which is why I specified the
4026B chip for the reaction timer—I could not find a modern equivalent that
will drive seven-segment numeric displays directly, and I didn’t want you to
have to deal with more parts than necessary).
If you check online suppliers such as Mouser.com you’ll find that the HC family is
by far the most popular right now. They are all available in through-hole format
(to fit your breadboard and perforated board). They have the high input imped-
ance of CMOS (which is useful) and they have the same pin identities as the old
74LSxx series.
Abbreviations
When looking at data sheets, you are likely to encounter some or all of these
abbreviations:
• VOH min: Minimum output voltage in high state
• VOL max: Maximum output voltage in low state
• VIH min: Minimum input voltage to be recognized as high
• VIL max: Maximum input voltage recognized as low
Background
Logic gate origins
The 7400 family of integrated circuits was introduced by
Texas Instruments, beginning with the 7400 NAND gate in
1962. Other companies had sold logic chips previously, but
the 7400 series came to dominate the market. The Apollo
lunar missions used a computer built with 7400 chips, and
they were a mainstay of minicomputers during the 1970s.
RCA introduced its 4000 series of logic chips in 1968, built
around CMOS transistors; Texas Instruments had chosen
TTL. The CMOS chips used less power, thus generating much
less heat and enabling flexible circuit design, as each chip
could power many others. CMOS was also tolerant of wide
voltage ranges (from 3 to 15 volts) but prohibited switching
speeds faster than around 1MHz. TTL was 10 times faster.
Design tweaks gradually eradicated the speed penalty for
CMOS, and TTL chips have become relatively rare. Still, some
people retain a special nostalgic loyalty to“the logic gates
that went to the moon.”A hardcore enthusiast named Bill
Buzbee has built an entire web server from TTL-type 7400
chips, currently online at http://magic-1.org. Figure 4-65
shows just one of the handmade circuit boards that Bill as-
sembled to run his computer.
Figure 4-65. Hobbyist Bill Buzbee built himself a web server
entirely from 7400 series logic chips, the oldest of which was
fabricated back in 1969. The web server can be found online at
http://magic-1.org, displaying pictures of itself and details of
its construction. The picture here that Bill took shows just one
of the circuit boards of this remarkable project.

Chips, Ahoy! 193
Fundamentals
Common part numbers
Each 14-pin chip can contain four 2-input gates, three
3-input gates, two 4-input gates, one 8-input gate, or six
single-input inverters, as shown in the following table.
2 input 3 input 4 input 8 input
AND 7408 7411 7421
NAND 7400 7410 7420 7430
OR 7432 744078*
NOR 7402 7427 744078*
XOR 7486
XNOR 747266
Inverter (1 input) 7404
*The 744078 has an OR output and a NOR output on the same chip.
Figures 4-66 through 4-74
show the internal connec-
tions of the logic chips that
you are most likely to use.
Note that the 7402 NOR
gate has its logical inputs
and outputs arranged dif-
ferently from all the other
chips.
Figure 4-66. Figures 4-66
through 4-74 show pinouts
for some of the most widely
used logic chips. Note that the
inputs of the 7402 are reversed
compared with the other chips.
7402
Quad
2-Input
NOR gate
3
4
1
2
14
13
12
11
6
7
10
9
8
5
7404 Hex
Inverter
3
4
1
2
14
13
12
11
6
7
10
9
8
5
Figure 4-67
7410
Triple
3-Input
NAND gate
3
4
1
2
14
13
12
11
6
7
10
9
8
5
Figure 4-68
7411
Triple
3-Input
AND gate
3
4
1
2
14
13
12
11
6
7
10
9
8
5
Figure 4-69
7420
Dual
4-Input
NAND gate
3
4
1
2
14
13
12
11
6
7
10
9
8
5
Figure 4-70
7421
Dual
4-Input
AND gate
3
4
1
2
14
13
12
11
6
7
10
9
8
5
Figure 4-71
7427
Triple
3-Input
NOR gate
14
7
1
2 13
3
4
12
11
6
10
9
8
5
Figure 4-72
7432
Quad
2-Input
OR gate
3
4
1
2
14
13
12
11
6
7
10
9
8
5
Figure 4-73
7486
Quad
2-Input
XOR gate
3
4
1
2
14
13
12
11
6
7
10
9
8
5
Figure 4-74

Chapter 4194
Fundamentals
Rules for connecting logic gates
Permitted:
• You can connect the input of a gate directly to your
regulated power supply, either positive side or nega-
tive side.
• You can connect the output from one gate directly to
the input of another gate.
• The output from one gate can power the inputs of
many other gates (this is known as“fanout”). The exact
ratio depends on the chip, but you can always power at
least ten inputs with one logic output. The output from
a logic chip can drive the trigger (pin 3) of a 555 timer.
The output from the timer can then deliver 100mA,
easily enough for half-a-dozen LEDs or a small relay.
• Low input doesn’t have to be zero. A 74HCxx logic gate
will recognize any voltage up to 1 volt as“low.”
• High input doesn’t have to be 5 volts. A 74HCxx logic
gate will recognize any voltage above 3.5 volts as
“high.”
See Figures 4-75 and 4-76 for a comparison of permit-
ted voltages on the input and output side of 74HCxx and
74LSxx chips.
Atmost0.1V
Acceptable input
signal range
Guaranteed output
signal range
Max power
consumption
at each pin:
1uA (sink)
1uA (source)
Max power
output
at each pin:
4mA (source)
4mA (sink)
5V
DC
74HCXX
Logic Gate
Minimum
3.5V
Maximum1.0V
Low High
Low High
Atleast4.4V
Figure 4-75. Each family of logic chips, and each generation
in each family, has different standards for input and output
minimum and maximum voltages. This diagram shows the
standards used by the HC generation of the CMOS family,
which was chosen for most of the projects in this book. Note
that the current required for input is minimal compared with
the current available for output. The power supply to the chip
makes up the difference.
Atmost0.4V
Acceptable input
signal range
Guaranteed output
signal range
Max power
consumption
at each pin:
20uA (sink)
400uA (source)
Max power
output
at each pin:
0.4mA (source)
4.0mA (sink)
5V
DC
74LSXX
Logic Gate
Minimum
2.0V
Maximum0.8V
Low High
Low High
Atleast
2.7V
Figure 4-76. Because the LS generation of the TTL family has
such different tolerances for input voltages and different
standards for output voltages, the LS generation of TTL chips
should not be mixed in the same circuit as the HC generation
of CMOS chips, unless pull-up resistors are used to bring the
LS chips into conformance with standards expected by the HC
chips. See Experiment 21 for a case study in using LS chips.

Chips, Ahoy! 195
Fundamentals
Rules for connecting logic gates (continued)
Not permitted:
• No floating-input pins! On CMOS chips such as the HC
family, you must always connect all input pins with a
known voltage, even if they supply a gate on the chip
that you’re not using. When you use a SPST switch to
control an input, remember that in its“off”position, it
leaves the input unconnected. Use a pull-up or pull-
down resistor to prevent this situation. See Figure 4-77.
• Don’t use an unregulated power supply, or more than 5
volts, to power 74HCxx or 74LSxx logic gates.
• Be careful when using the output from a logic gate to
power even a low-current LED. Check how many mil-
liamps are being drawn. Also be careful when“sharing”
the output from a logic gate with the input of another
gate, at the same time that it is driving an LED. The LED
may pull down the output voltage, to a point where
the other gate won’t recognize it. Always check cur-
rents and voltages when modifying a circuit or design-
ing a new one.
• Never apply a significant voltage or current to the
output pin of a logic gate. In other words, don’t force
an input into an output.
• Never link the outputs from two or more logic gates. If
they must share a common output wire, use diodes to
protect them from each other. See Figure 4-78.
Not
good
Good
1
1
Not
good
Good
1
1
Figure 4-77. Because a CMOS chip is so sensitive to input
fluctuations, a logical input should never be left “floating,” or
unattached to a defined voltage source. This means that any
single-throw switch or pushbutton should be used with a pull-
up or pull-down resistor, so that when the contacts are open,
the input is still defined.
Not
Good
Good Good
Figure 4-78. The output from one logic gate must not be allowed to feed back into the output from another logic gate. Diodes can
be used to isolate them, or they can be linked via another gate.

Chapter 4196
In the 74HCxx logic family, each input of a logic gate consumes just a micro-
amp, while the output can source 4 milliamps. This seems paradoxical: how
can the chip give out more than it takes in?The answer is that it also consumes
power from the power supply attached to pins 7 and 14. That’s where the ad-
ditional electricity comes from.
Because the logical output from a chip can be greater than the logical input,
we can put the chip in a state where it keeps itself“switched on”in a way which
is similar to the way the relay in the alarm project was wired to lock itself on.
The simplest way to do this in a logic chip is by feeding some of the output
back to one of the inputs.
Figure 4-79 shows an AND gate with one of its inputs wired to positive and its
other input held low by a pull-down resistor, with a pushbutton that can make
the input high. A signal diode connects the output of the chip back to the
pushbutton-controlled input. Remember that the diode has a mark on it indi-
cating the end which should be connected to the negative side of the power
supply, which in this case will be the end of the 10K resistor.
The schematic in Figure 4-79 shows how the circuit should look in breadboard
format. Figure 4-80 shows it in a simpler format.
From this point on, I won’t bother to show the power regulator and the capacitors
associated with it. Just remember to include them every time you see the power sup-
ply labeled as “5V DC Regulated.”
When you switch on the power, the LED is dark, as before.The AND gate needs
a positive voltage on both of its logical inputs, to create a positive output, but
it now has positive voltage only on one of its inputs, while the other input
is pulled down by the 10K resistor. Now touch the pushbutton, and the LED
comes on. Let go of the pushbutton, and the LED stays on, because the posi-
tive output from the AND gate circulates back through the diode and is high
enough to overcome the negative voltage coming through the pull-down
resistor.
The output from the AND gate is powering its own input, so the LED will stay
on until we disconnect it. This arrangement is a simple kind of“latch,”and can
be very useful when we want an output that continues after the user presses
and releases a button.
You can’t just connect the output from the gate to one of its inputs using an
ordinary piece of wire, because this would allow positive voltage from the tac-
tile switch to flow around and interfere with the output signal. Remember, you
must never apply voltage to the output pin of a logic gate. The diode prevents
this from happening.
If you’ve grasped the basics of logic gates, you’re ready now to continue to our
first real project, which will use all the information that I’ve set out so far.
74HC08
AND
gate
5VDC Regulated
10K
1K
Figure 4-79. Using a diode, the logical
output from a gate can be allowed to feed
back to one of its inputs, so that the gate
latches after receiving a brief logical input
pulse.
Figure 4-80. The breadboard-format sche-
matic in is simplified here to show more
clearly the way in which a gate can latch
itself after receiving an input pulse.

Chips, Ahoy! 197
Suppose you want to prevent other people from using your computer. I can
think of two ways to do this: using software, or using hardware. The software
would be some kind of startup program that intercepts the normal boot se-
quence and requests a password.You could certainly do it that way, but I think
it would be more fun (and more relevant to this book) to do it with hardware.
What I’m imagining is a numeric keypad requiring the user to enter a secret
combination before the computer can be switched on.
You will need:
• Numeric keypad. As specified in the shopping list at the beginning of this
chapter, it must have a“common terminal”or“common output.”The sche-
matic in Figure 4-82 shows what I mean. Inside the keypad, one conductor
(which I have colored red to distinguish it from the others) connects with
one side of every pushbutton. This conductor is “common”to all of them.
It emerges from the keypad on an edge connector or set of pins at the
bottom, which I’ve colored yellow.
1
4
7
*
2
5
8
0
3
6
9
#
Figure 4-82. A keypad of the type required for Experiment 20 incorporates a common
terminal connected to one side of each of the 12 pushbuttons. The wire from the common
terminal is shown red, here, to make it more easily identifiable.
• Keypads that use “matrix encoding” won’t work with the circuit that I’m
going to describe. If the Velleman keypad, which I recommend, is unavail-
able, and you can’t find another like it, you can use 12 separate SPST push-
buttons. Of course, that will cost a little more.
• 74HC08 logic chip containing four AND gates. Quantity: 1.
• 74HC04 logic chip containing six inverters. Quantity: 1.
• 555 timer chip. Quantity: 1.
TheWarranty Issue
If you follow this project all the way
to its conclusion, you’ll open your
desktop computer, cut a wire, and
saw a hole in the cabinet. Without a
doubt, this will void your warranty.
If this makes you nervous, here are
three options:
1. Breadboard the circuit for fun, and
leave it at that.
2. Use the numeric keypad on some
other device.
3. Use it on an old computer.
Figure 4-81. Caution: This just might void
your warranty.

Chapter 4198
• Latching relay, 5 volt, DPST or DPDT,“2 form C”package, Panasonic DS2E-
SL2-DC5V or similar. Must have two separate coils (one to latch, one to
unlatch) with separate inputs. Quantity: 1.
• LEDs, 5mm generic, your choice of colors. Quantity: 3.
• Ribbon cable, with six conductors minimum, if you want to do a really
neat job. You can use a cable of the type sold for hard drives, and split off
the six conductors that you need, or shop around on eBay.
• Tools to open your computer, drill four holes, and make saw cuts between
the holes, to create a rectangular opening for the keypad (if you want to
take this project to its conclusion). Also, four small bolts to attach the key-
pad to the computer cabinet after you create the opening for it.
The Schematic
This time I’d like you to study the schematic before building anything. Let’s
start with the simplified version, shown in Figure 4-83.
1 8
555
timer
0
1
2
3
4
5
6
7
8
9
#
Computer
on switch
Logic gate
power input pins
5VDC
Regulated
*
Figure 4-83. A simplified schematic showing the basic structure of the combination lock
circuit.

Chips, Ahoy! 199
I want this to be a battery-powered circuit, so that you don’t have to run a
separate power supply to it or (worse) try to tap into your computer’s 5-volt
bus. Battery power means that the circuit has to be “off” most of the time, to
prevent the battery from running down. Because the keypad has two spare
buttons (the asterisk and the pound sign), I’m going to use the asterisk as the
“power on” button. When you press it, the LED at the top of the schematic
lights up to confirm that everything’s working, and the button sends power to
the two logic chips and the 555 timer. You have to hold down the asterisk but-
ton while you punch in a three-digit code to unlock the computer.
Arbitrarily, I’ve chosen 1-4-7 as the three-digit code. Let’s track what happens
when you enter this sequence. (Naturally, if you build the circuit, you can wire
it to choose any three digits you prefer.)
Pressing the 1 button sends positive power to one logical input of the first
AND gate. The other logical input of this gate is also positive, because an in-
verter is supplying it, and the input of the inverter is being held negative by
a pull-down resistor. When an inverter has a negative input, it gives a positive
output, so pressing the 1 button activates the AND gate, and makes its output
positive. The AND gate locks itself on, as its output cycles back to its switched
input via a diode. So the gate output remains high even after you let go of the
1 button.
The output from the first AND gate also supplies one logical input of the sec-
ond AND gate. When you press the 4 button, you send positive voltage to the
other logical input of this AND gate, so its output goes high, and it locks itself
on, just as the first gate did.
The second AND gate feeds the third AND gate, so when you press the 7
button, the third AND gate changes its output from low to high. This passes
through an inverter, so the output from the inverter goes from high to low.
This in turn goes to the trigger of a 555 timer wired in monostable mode.
When the trigger of a 555 timer goes from high to low, the timer emits a posi-
tive pulse through its output, pin 3. This runs down to the upper coil of the
latching relay, and also flashes an LED to confirm that the code has been ac-
cepted and the relay has been activated.
Two of the contacts in the relay are wired into the power-up button of your
computer. A little later in this description I’ll explain why this should be safe
with any modern computer.
Because we’re using a latching relay, it flips into its“on”state and remains there,
even when the power pulse from the timer ends. So now you can let go of the
asterisk button to disconnect the battery power to your combination lock, and
press the power-up button that switches on your computer.
At the end of your work session, you shut down your computer as usual, then
press the pound button on your keypad, which flips the relay into its other
position, reactivating the combination lock.

Chapter 4200
Incorrect Inputs
What happens if you enter the wrong code? If you press any button other than
1, 4, or 7, it sends positive voltage to the inverter near the top of the sche-
matic. The positive voltage overwhelms the negative voltage being applied to
the inverter through a pull-down resistor, and causes the inverter to output a
negative voltage, which it applies to one of the logical inputs of the first AND
gate. If the AND gate was locked on, the negative input will switch it off. If it
was supplying the second AND gate, it’ll switch that one off too.
Thus, any error when entering the first, second, or third digit of the secret code
will reset the AND gates, forcing you to begin the sequence all over again.
What if you enter 1, 4, and 7 out of their correct sequence? The circuit won’t
respond. The third AND gate needs a high input supplied by the second AND
gate, and the second AND gate needs a high input supplied by the first AND
gate. So you have to activate the AND gates in the correct sequence.
Questions
Why did I use a 555 timer to deliver the pulse to the relay? Because the logical
output from an AND gate cannot deliver sufficient power. I could have passed
it through a transistor, but I liked the idea of a pulse of a fixed length to flip the
relay and illuminate an LED for about 1 second, regardless of how briefly the user
presses the 7 button.
Why do I need three LEDs? Because when you’re punching buttons to un-
lock your computer, you need to know what’s going on. The Power On LED
reassures you that your battery isn’t dead. The Relay Active LED tells you that
the system is now unlocked, in case you are unable to hear the relay click. The
System Relocked LED reassures you that you have secured your computer.
Because all the LEDs are driven either directly from the 5-volt supply or from
the output of the 555 timer, they don’t have to be low-current LEDs and can be
used with 330Ω series resistors, so they’ll be nice and bright.
How do you connect the keypad with the circuit? That’s where your ribbon
cable comes in. You carefully strip insulation from each of the conductors,
and solder them to the contact strip or edge connector on your keypad. Push
the conductors on the other end of the cable into your breadboard (when
you’re test-building the circuit) or solder them into perforated board (when
you’re building it permanently). Find a convenient spot inside your computer
case where you can attach the perforated board, with double-sided adhesive
or small bolts or whatever is convenient. Include a 9-volt battery carrier, and
don’t forget your power regulator to step the voltage down to 5 volts.
Breadboarding
No doubt you have realized by now that breadboards are very convenient as a
quick way to push in some components and create connections, but the layout
of their conductors forces you to put components in unintuitive configurations.
Still, if you carefully compare the breadboard schematic in Figure 4-83 with the
simplified schematic in Figure 4-84, you’ll find that the connections are the same.

Chips, Ahoy! 201
To help it make sense, I’ve shown the logic gates that exist inside the chips. I’ve
also colored the power supply wires, as before, to reduce the risk of confusion.
The positive side of the supply goes only to the common terminal on your
keypad, and you have to press the asterisk key to send the power back down
the ribbon cable, to supply the chips.
Note that the “wrong” numbers on the keypad are all shorted together. This
will create some inconvenience if you want to change the combination in the
future. I’ll suggest a different option in the “enhancements” section that fol-
lows. For now, ideally, you should run a wire from every contact on your key-
pad, down to your circuit on its breadboard, and short the “wrong” keypad
numbers together with jumper wires on the breadboard.
Also note that if you use a meter to test the inputs to the AND gates, and you
touch your finger against the meter probe while doing so, this can be suffi-
cient to trigger the sensitive CMOS inputs and give a false positive.
Computer
power-up
switch
0
7
1
4
5VDC Regulated
(from 9V battery)
2
3
5
6
8
9
#
*
74HC08
74HC04
555
330
330
330
10K
10K
10K
10uF
0.1uF
100K
Figure 4-84. The combination lock schematic redrawn to show how the components can
be laid out on a breadboard.
If you build the circuit and you can’t
understand why everything’s dead,
it’s most likely because you forgot to
hold down the asterisk button.

Chapter 4202
One Little Detail: The Computer Interface
Old computers used to have a big switch at the back, attached to the heavy
metal box inside the computer, that transformed house current to regulated
voltages that the computer needs. Most modern computers are not designed
this way; you leave the computer plugged in, and you touch a little button on
the box (if it’s a Windows machine) or the keyboard (if it’s a Mac), which sends
a low-voltage pulse to the motherboard.
This is ideal from our point of view, because we don’t have to mess with high
voltages. Don’t even think of opening that metal box with the fan mounted in
it, containing the computer power supply. Just look for the wire (usually con-
taining two conductors, on aWindows machine) that runs from the“power up”
button to the motherboard.
To check that you found the right one, make sure that your computer is un-
plugged, ground yourself (because computers contain CMOS chips that are
sensitive to static electricity) and very carefully snip just one of the two con-
ductors in the wire. Now plug in your computer and try to use the“power up”
button. If nothing happens, you’ve probably cut the right wire. Even if you cut
the wrong wire, it still prevented your computer from booting, which is what
you want, so you can use it anyway. Remember, we are not going to introduce
any voltage to this wire. We’re just going to use the relay as a switch to recon-
nect the conductor that you cut. You should have no problem if you maintain
a cool and calm demeanor, and look for that single wire that starts everything.
Check online for the maintenance manual for your computer if you’re really
concerned about making an error.
After you find the wire and cut just one of its conductors, unplug your com-
puter again, and keep it unplugged during the next steps.
Find where the wire attaches to the motherboard. Usually there’s a small un-
pluggable connector. First, mark it so that you know how to plug it back in the
right way around, and then disconnect it while you follow the next couple of
steps.
Strip insulation from the two ends of the wire that you cut, and solder an ad-
ditional piece of two-conductor wire, as shown in Figure 4-85, with heat-shrink
tube to protect the solder joints. (This is very important!)
Run your new piece of wire to the latching relay, making sure you attach it to
the pair of contacts which close, inside the relay, when it is energized by the
unlocking operation. You don’t want to make the mistake of unlocking your
computer when you think you’re locking it, and vice versa.
Reconnect the connector that you disconnected from your motherboard, plug
in your computer, and try to power it up. If nothing happens, this is probably
good! Now enter the secret combination on your keypad (while holding down
the asterisk button to provide battery power) and listen for the click as the re-
lay latches. Now try the“power up”button again, and everything should work.

Chips, Ahoy! 203
Power Up
button on
computer
Solder
joints
Heat-shrink tubing
(not yet shrunk)
To your
latching
relay
Connector
Computer motherboard
Figure 4-85. The combination lock project can be interfaced with a typical desktop com-
puter by cutting one conductor in the wire from the “power up” pushbutton, soldering an
extension, and covering the joints with heat-shrink tube.
Enhancements
At the end of any project, there’s always more you can do.
To make this setup more secure, you could remove the usual screws that secure
the case of the computer, and replace them with tamper-proof screws. Check any
online source for“tamper-proof screws,”such as http://www.mcmaster.com. Natu-
rally, you will also need the special tool that fits the screws, so that you can install
them (or remove them, if your security system malfunctions for any reason).

Chapter 4204
Another enhancement could be an additional 555 timer that is activated by
the asterisk button, and delivers power to the other chips for, say, a limited
period of 30 seconds, allowing you that much time to unlock the system. This
would eliminate the need to hold down the asterisk button while you enter
the unlocking code. A 555 timer can supply power to all the other chips, be-
cause they don’t use very much. I omitted this feature for the sake of simplicity.
Yet another enhancement, if you are security-crazed, is to go for a four-button
code. After all, the 74HC08 chip still has one unused AND gate. You could in-
sert that into the chain of the existing AND gates and wire it to another keypad
button of your choice.
Still another enhancement would be a way to change the code without unsol-
dering and resoldering wires.You can use the miniature sockets that I suggest-
ed in the heartbeat flasher project. These should enable you to swap around
the ends of your wires from the keypad.
And for those who are absolutely, positively, totally paranoid, you could fix
things so that entering a wrong code flips a second high-amperage relay
which supplies a massive power overload, melting your CPU and sending a
big pulse through a magnetic coil clamped to your hard drive, instantly turn-
ing the data to garbage (Figure 4-86). Really, if you want to protect informa-
tion, messing up the hardware has major advantages compared with trying
to erase data using software. It’s faster, difficult to stop, and tends to be per-
manent. So, when the Record Industry Association of America comes to your
home and asks to switch on your computer so that they can search for illegal
file sharing, just accidentally give them an incorrect unlocking code, sit back,
and wait for the pungent smell of melting insulation.
If you pursue this option, I definitely take no responsibility for the consequences.
On a more realistic level, no system is totally secure. The value of a hardware
locking device is that if someone does defeat it (for instance, by figuring out
how to unscrew your tamper-proof screws, or simply ripping your keypad out
of the computer case with metal shears), at least you’ll know that something
happened—especially if you put little dabs of paint over the screws to re-
veal whether they’ve been messed with. By comparison, if you use password-
protection software and someone defeats it, you may never know that your
system has been compromised.
Figure 4-86. For those who are absolutely,
positively, totally paranoid: a meltdown/
self-destruct system controlled by a secret
key combination provides enhanced
protection against data theft or intrusions
by RIAA investigators asking annoying
questions about file sharing.

Chips, Ahoy! 205
The next project is going to get us deeper into the concept of feedback, where
the output is piped back to affect the input—in this case, blocking it. It’s a small
project, but quite subtle, and the concepts will be useful to you in the future.
You will need:
• 74HC32 chip containing four OR gates. Quantity: 1.
• SPDT switch. Quantity: 1.
• Various resistors.
• 5V supply using power regulator as before.
The Goal
On quiz shows such as Jeopardy, contestants race to answer each question.
The first person who hits his answer button automatically locks out the other
contestants, so that their buttons become inactive. How can we make a circuit
that will do the same thing?
If you search online, you’ll find several hobby sites where other people have
suggested circuits to work this way, but they lack some features that I think are
necessary.The approach I’m going to use here is both simpler and more elabo-
rate. It’s simpler because it has a very low chip count, but it’s more elaborate in
that it incorporates“quizmaster control”to make a more realistic game.
I’ll suggest some initial ideas for a two-player version. After I develop that idea,
I’ll show how it could be expanded to four or even more players.
A Conceptual Experiment
I want to show how this kind of project grows from an idea to the finished
version. By going through the steps of developing a circuit, I’m hoping I may
inspire you to develop ideas of your own in the future, which is much more
valuable than just replicating someone else’s work. So join me in a conceptual
experiment, thinking our way from a problem to a solution.
First consider the basic concept: two people have two buttons, and whoever
goes first locks out the other person. I always find it helps me to visualize this
kind of thing if I draw a sketch, so that’s where I’ll begin. In Figure 4-87, the
signal from each button passes through a component that I’ll call a “button
blocker,”activated by the other person’s button. I’m not exactly sure what the
button blocker will be or how it will work, yet.
Now that I’m looking at it, I see a problem here. If I want to expand this to three
players, it will get complicated, because each player must activate the“button
blockers”of two opponents. Figure 4-88 shows this. And if I have four players,
it’s going to get even more complicated.
Anytime I see this kind of complexity, I think there has to be a better way.
Button
Blocker
Button
Blocker
Figure 4-87. The basic concept of the quiz
project is that the output from one button
should feed back to intercept the output
of another button. At this point, the way in
which the “button blocker” circuit works
has not been figured out.

Chapter 4206
Also, there’s another problem. After a player lets his finger off the button, the
other players’buttons will be unblocked again. I need a latch to hold the signal
from the first player’s button and continue to block the other players.
Button
Blocker
Button
Blocker
Button
Blocker
Figure 4-88. The quiz concept becomes more complicated when an additional pushbutton
is added. Now each button must block two other buttons. If a fourth button is added, the
circuit will become unmanageably complex. There has to be a better way.
This now sounds even more complicated. But wait a minute, if I have a latch
which allows the winning player to take his finger off his button, I don’t care if
any of the buttons are being pressed anymore—including the button of the
winning player. As soon as his signal is latched, all the buttons can be blocked.
This makes things much simpler. I can summarize it as a sequence of events:
1. First player presses his button.
2. The signal is latched.
3. The latched signal feeds back and blocks all the buttons.
The new sketch in Figure 4-89 shows this. Now the configuration is modular,
and can be expanded to almost any number of players, just by adding more
modules.
There’s something important missing, though: a reset switch, to put the sys-
tem back to its starting mode after the players have had time to press their
buttons and see who won. Also, I need a way to prevent players from pressing
their buttons too soon, before the quizmaster has finished asking the ques-
tion. Maybe I can combine this function in just one switch, which will be under
the quizmaster’s control. In its Reset position, the switch can reset the system
and remove power to the buttons. In its Play position, the switch stops hold-
ing the system in reset mode, and provides power to the buttons. Figure 4-90
shows this. I’ve gone back to showing just two players, to minimize the clutter
of lines and boxes, but the concept is still easily expandable.

Chips, Ahoy! 207
Button
Blocker
Latch
Button
Blocker
Latch
Button
Blocker
Latch
Figure 4-89. If a latch is added below each button, it can
retain one input and then block all inputs from all buttons.
This simplifies the concept.
Button
Blocker
Latch
Reset
Play Button
Blocker
Latch
Figure 4-90. A quizmaster switch will be needed to
activate the buttons initially and then reset the circuit
after a winning input has been recorded.
Now I have to deal with a logic problem in the diagram. The way I’ve drawn
it, after the output from the lefthand latch goes up to the“button blockers,”it
can also run down the wire to the other half of the circuit (against the direc-
tion to the arrows), because everything is joined together. In other words, if
the lefthand LED lights up, the righthand LED will light up, too. How can I stop
this from happening?
Well, I could put diodes in the “up” wires to block current from running down
them. But I have a more elegant idea: I’ll add an OR gate, because the inputs to
an OR gate are separated from each other electrically. Figure 4-91 shows this.
Usually an OR gate has only two logical inputs.Will this prevent me from adding
more players? No, because you can actually buy an OR that has eight inputs. If
any one of them is high, the output is high. For fewer than eight players, I can
short the unused inputs to ground, and ignore them.
Looking again at Figure 4-91, I’m getting a clearer idea of what the thing I’ve
called a “button blocker”should actually be. I think it should be another logic
gate. It should say, “If there’s only one input, from a button, I’ll let it through.
But if there is a second input from the OR gate, I won’t let it through.”
That sounds like a NAND gate, but before I start choosing chips, I have to de-
cide what the latch will be. I can buy an off-the-shelf flip-flop, which flips“on”if
it gets one signal and“off”if it gets another, but the trouble is, chips containing
flip-flops tend to have more features than I need for a simple circuit like this.
Therefore I’m going to use 555 timers again, in flip-flop mode. They require
very few connections, work very simply, and can deliver a good amount of cur-
rent. The only problem with them is that they require a negative input at the
trigger pin to create a positive output. But I think I can work with that.
Button
Blocker
Latch
Reset
Play Button
Blocker
Latch
OR
Figure 4-91. To prevent the output from one
latch feeding back around the circuit to the
output from another latch, the outputs can
be combined in an OR gate.

Chapter 4208
So now, finally, here’s a simplified schematic, in Figure 4-92. I like to show the
pins of the 555 timers in their correct positions, so I had to move the compo-
nents around a little to minimize wire crossovers, but you can see that logi-
cally, it’s the same basic idea.
Before you try to build it, just run through the theory of it, because that’s the
final step, to make sure there are no mistakes. The important thing to bear in
mind is that because the 555 needs a negative input on its trigger pin to create
its output, when any of the players presses a button, the button has to create a
negative“flow”through the circuit. This is a bit counterintuitive, so I’m includ-
ing a three-step visualization in Figure 4-93, showing how it will work.
In Step 1, the quizmaster has asked a question and flipped his switch to the
right, to supply (negative) power to the players’ buttons. So long as no one
presses a button, the pull-up resistors supply positive voltage to OR2 and OR3.
An OR gate has a positive output if it has any positive input, so OR2 and OR3
keep the trigger inputs of the 555 timers positive. Their outputs remain low,
and nothing is happening yet.
In Step 2, the lefthand player has pressed his button. Now OR2 has two nega-
tive inputs, so its output has gone low. But IC1 hasn’t reacted yet.
In Step 3, just a microsecond later, IC1 has sensed the low voltage on its trig-
ger, so its output from pin 3 has gone high, lighting the LED. Remember, this
555 timer is in flip-flop mode, so it locks itself into this state immediately.
Meanwhile its high output also feeds back to OR1. Because OR1 is an OR gate,
just one high input is enough to make a high output, so it feeds this back to
OR2 and OR3. And now that they have high inputs, their outputs also go high,
and will stay high, regardless of any future button-presses.
1 8
IC1
1 8
IC2
OR1 OR2 OR3
S1
S2 S3
R2
R4
R1
R3
1 8
IC1
1 8
IC2
OR1 OR2 OR3
S1
S2 S3
R2
R4
R1
R3
1 8
IC1
1 8
IC2
OR1 OR2 OR3
S1
S2 S3
R2
R4
R1
R3
Figure 4-93. These three schematics show the prevalence of higher and lower voltages
(red and blue lines) through the quiz circuit when a pushbutton is pressed.
Because OR2 and OR3 now have high inputs and outputs, IC1 and IC2 cannot be
triggered. But IC1 is still locked into its“on”state, keeping the LED illuminated.
1 8
555
timer
1 8
OR1 OR2 OR3
S1
S2 S3
R2
R4
R1
R3
555
timer
Figure 4-92. Now that the basic concept
of the quiz circuit has been roughed out,
specific components can be inserted, with
compatible inputs and outputs.

Chips, Ahoy! 209
The only way to change IC1 is if the quizmaster flips his switch back to the left.
That applies negative power to the reset pins of both the timers. Consequently
their outputs go low, the LED goes out, and the circuit goes back into the same
state as where it started. Having reset it, the quizmaster can ask another ques-
tion, but the players’ buttons are not activated until the quizmaster flips the
switch back to the right again.
There’s only one situation that I haven’t addressed: what if both players press
their buttons absolutely simultaneously? In the world of digital electronics,
this is highly unlikely. Even a difference of a microsecond should be enough
time for the circuit to react and block the second button. But if somehow both
buttons are pressed at the same instant, both of the timers should react, and
both of the LEDs will light up, showing that there has been a tie.
In case you feel a little uncertain about the way in which a two-player circuit
can be upgraded to handle extra players, I’ve included a simplified three-player
schematic in Figure 4-94.
Breadboarding It
Now it’s time to create a schematic that’s as close to the breadboard layout
as possible, so that you can build this thing easily. The schematic is shown in
Figure 4-95 and the actual components on a breadboard are in Figure 4-96.
Because the only logic gates that I’ve used are OR gates, and there are only three
of them, I just need one logic chip: the 74HC32, which contains four 2-input OR
gates. (I’ve grounded the inputs to the fourth). The two OR gates on the left
side of the chip have the same functions as OR2 and OR3 in my simplified
schematic, and the OR gate at the bottom-right side of the chip works as OR1,
receiving input from pin 3 of each 555 timer. If you have all the components,
you should be able to put this together and test it quite quickly.
You may notice that I’ve made one modification of the previous schematic. A
0.01 µF capacitor has been added between pin 2 of each 555 timer (the Input)
and negative ground. Why? Because when I tested the circuit without the ca-
pacitors, sometimes I found that one or both of the 555 timers would be trig-
gered simply by flipping S1, the quizmaster switch, without anyone pressing
a button.
At first this puzzled me. How were the timers getting triggered, without any-
one doing anything? Maybe they were responding to “bounce” in the quiz-
master switch. Sure enough, the small capacitors solved the problem. They
may also slow the response of the 555 timers fractionally, but not enough to
interfere with slow human reflexes.
As for the buttons, it doesn’t matter if they“bounce,”because each timer locks
itself on at the very first impulse and ignores any hesitations that follow.
You can experiment building the circuit, disconnecting the 0.01 µF capacitors,
and flipping S1 to and fro a dozen times. If you have a high-quality switch, you
may not experience any problem. If you have a lower-quality switch, you may
see a number of “false positives.” I’m going to explain more about “bounce,”
and how to get rid of it, in the next experiment.
1 8
IC1
1 8
IC2
OR2 OR3
S1
S2 S3
R2
R1
R3
R4
1 8
IC3
S4
OR4OR1
Figure 4-94. The two-player schematic in
can be easily upgraded to a three-player
version, as shown here, provided the first
OR gate can handle three inputs.

Chapter 4210
1 8
555
1 8
555
74HC32
5V DC regulated
10K
10K
OR2
OR3
OR1
10K
S2
S3
S1
330
0.01
0.01
330
Figure 4-95. Applying the simplified schematic to a breadboard inevitably entails
a wiring layout that is less intuitively obvious and appears more complex. The
connections are the same, though.
Figure 4-96. The quiz schematic applied to a
breadboard, to test the concept prior to full-scale
implementation.
Enhancements
After you breadboard the circuit, if you proceed to build a permanent version,
I suggest that you expand it so that at least four players can participate. This
will require an OR gate capable of receiving four inputs. The 74HC4078 is the
obvious choice, as it allows up to eight. Just connect any unused inputs to
negative ground.
Alternatively, if you already have a couple of 74HC32 chips and you don’t want
to bother ordering a 74HC4078, you can gang together three of the gates in-
side a single 74HC32 so that they function like a four-input OR. Look at the
simple logic diagram in Figure 4-97 showing three ORs, and remember that
the output from each OR will go high if at least one input is high.
And while you’re thinking about this, see if you can figure out the inputs and
output of three ANDs in the same configuration.
For a four-player game, you’ll also need two additional 555 timers, of course,
and two more LEDs, and two more pushbuttons.
As for creating a schematic for the four-player game—I’m going to leave that
to you. Begin by sketching a simplified version, just showing the logic symbols.
Then convert that to a breadboard layout. And here’s a suggestion: pencil, pa-
per, and an eraser can still be quicker, initially, than circuit-design software or
graphic-design software, in my opinion.
Figure 4-97. Although a four-input OR gate
is not manufactured, its functionality can
be achieved easily by linking three 2-input
OR gates together.

Chips, Ahoy! 211
I mentioned in the previous experiment that“bounce”from the buttons in the
circuit wouldn’t be a problem, because the buttons were activating 555 tim-
ers that were wired in bistable, flip-flop mode. As soon as the timer receives
the very first pulse, it flips into its new state and flops there, ignoring any ad-
ditional noise in the circuit. So can we debounce a switch or a button using a
flip-flop? And as some 74HCxx chips are available containing flip-flops, can we
use them?
The answers are yes, and yes, although it’s not quite as simple as it sounds.
You will need:
• 74HC02 logic chip containing 4 NOR gates. 74HC00 logic chip containing
4 NAND gates. Quantity: 1 of each.
• SPDT switch. Quantity: 1.
• LEDs, low-current. Quantity: 2.
• 10K resistors and 1K resistors. Quantity: 2 of each.
Assemble the components on your breadboard, following the schematic
shown in Figure 4-98. When you apply power (through your regulated 5-volt
supply), one of the LEDs should be lit.
74HC02
10K
5V DC Regulated
10K
1K
1K
Figure 4-98. A simple circuit to test the behavior of two NOR gates wired as a simple flip-
flop that retains its state after an input pulse ceases.
Now I want you to do something odd. Please disconnect the SPDT switch by
taking hold of the wire that connects the positive power supply to the pole of
the switch, and pulling the end of the wire out of the breadboard. When you
do this, you may be surprised to find that the LED remains lit.
Push the wire back into the breadboard, flip the switch, and the first LED
should go out, while the other LED should become lit. Once again, pull out the
wire, and once again, the LED should remain lit.
Here’s the take-home message:
• A flip-flop requires only an initial pulse.
• After that, it ignores its input.

Chapter 4212
How It Works
Two NOR gates or two NAND gates can function as a flip-flop:
• Use NOR gates when you have a positive input from a double-throw switch.
• Use NAND gates when you have a negative input from a double-throw
switch.
Either way, you have to use a double-throw switch.
I’ve mentioned the double-throw switch three times (actually, four times if you
count this sentence!) because for some strange reason, most introductory books
fail to emphasize this point.When I first started learning electronics, I went crazy
trying to understand how two NORs or two NANDs could debounce a simple
SPST pushbutton—until finally I realized that they can’t. The reason is that
when you power up the circuit, the NOR gates (or NAND gates) need to be
told in which state they should begin. They need an initial orientation, which
comes from the switch being in one state or the other. So it has to be a double-
throw switch. (Now I’ve mentioned it five times.)
I’m using another simplified multiple-step schematic, Figure 4-99, to show the
changes that occur as the switch flips to and fro with two NOR gates.To refresh
your memory, I’ve also included a truth table showing the logical outputs from
NOR gates for each combination of inputs.
Figure 4-99. Using two NOR gates in conjunction with a positive input through a SPDT
switch, this sequence of four diagrams shows how a flip-flop circuit responds.
Suppose that the switch is turned to the left. It sends positive current to the
lefthand side of the circuit, overwhelming the negative supply from the pull-
down resistor, so we can be sure that the NOR gate on the left has one posi-
tive logical input. Because any positive logical input will make the NOR give
a negative output (as shown in the truth table), the negative output crosses
over to the righthand NOR, so that it now has two negative inputs, which make
it give a positive output. This crosses back to the lefthand NOR gate. So, in this
configuration everything is stable.
Now comes the clever part. Suppose that you move the switch so that it
doesn’t touch either of its contacts. (Or suppose that the switch contacts are
bouncing, and failing to make a good contact. Or suppose you disconnect the
switch entirely.) Without a positive supply from the switch, the lefthand input

Chips, Ahoy! 213
of the left NOR gate goes from positive to negative, as a result of the pull-
down resistor. But the righthand input of this gate is still positive, and one
positive is all it takes to make the NOR maintain its negative output, so nothing
changes. In other words, the circuit has“flopped”in this state.
Now if the switch turns fully to the right and supplies positive power to the
righthand pin of the right NOR gate, quick as a flash, that NOR recognizes that
it now has a positive logical input, so it changes its logical output to negative.
That goes across to the other NOR gate, which now has two negative inputs,
so its output goes positive, and runs back to the right NOR.
In this way, the output states of the two NOR gates change places. They flip,
and then flop there, even if the switch breaks contact or is disconnected again.
The second set of drawings in Figure 4-100 shows exactly the same logic, using
a negatively powered switch and two NAND gates. You can use your 74HC00
chip, specified in the parts list for this experiment, to test this yourself.
Figure 4-100. The schematic from Figure 4-99 can be rewired with NAND gates and a
negative switched input.
Both of these configurations are examples of a jam-type flip-flop, so called be-
cause the switch forces it to respond immediately, and jams it into that state.
You can use this circuit anytime you need to debounce a switch (as long as it’s
a double-throw switch).
A more sophisticated version is a clocked flip-flop, which requires you to set
the state of each input first and then supply a clock pulse to make the flip-flop
respond.The pulse has to be clean and precise, which means that if you supply
it from a switch, the switch must be debounced—probably by using another
jam-type flip-flop! Considerations of this type have made me reluctant to use
clocked flip-flops in this book. They add a layer of complexity, which I prefer to
avoid in an introductory text.
What if you want to debounce a single-throw button or switch? Well, you have
a problem! One solution is to buy a special-purpose chip such as the 4490
“bounce eliminator,” which contains digital delay circuitry. A specific part
number is the MC14490PG from On Semiconductor. This contains six circuits
for six separate inputs, each with an internal pull-up resistor. It’s relatively ex-
pensive, however—more than 10 times the price of a 74HC02 containing NOR
gates. Really, it may be simpler to use double-throw switches that are easily
debounced as described previously.

Chapter 4214
This is the one experiment where I want you to use the 74LSxx generation of
the TTL logic family, instead of the 74HCxx family of CMOS. Two reasons: first,
I need to use the 7492 counter, which is unavailable in the HC family. And sec-
ond, you should know the basic facts about the LS series of TTL chips, as they
still crop up in circuits that you’ll find in electronics books and online.
In addition, you’ll learn about “open collector” TTL chips such as the 74LS06
inverter, which can be a convenient substitute for transistors when you want
to deliver as much as 40mA of current.
The idea of this circuit is simple enough: run a 555 timer sending very fast
pulses to a counter that counts in sixes, driving LEDs that are placed to imitate
the spots on a die. (Note that the word“die”is the singular of“dice.”) The coun-
ter runs so fast, the die-spots become a blur. When the user presses a button,
the counter stops arbitrarily, displaying an unpredictable spot pattern.
Dice simulations have been around for many, many years, and you can even
buy kits online. But this one will do something more: it will also demonstrate
the principles of binary code.
So, if you’re ready for the triple threat of TTL chips, open collectors, and binary,
let’s begin.
You will need:
• 74LS92 counter such as SN74LS92N by Texas Instruments. Quantity: 1 if
you want to create one die, 2 to make two dice.
• 74LS27 three-input NOR gate such as SN74LS27N by Texas Instruments.
Quantity: 1.
• 555 timers. Quantity: 1 if you want to make one die, 2 to make two dice.
• Signal diodes, 1N4148 or similar. Quantity: 4, or 8 to make two dice.
Seeing Binary
The counter that we dealt with before was unusual, in that its outputs were de-
signed to drive seven-segment numerals. A more common type has outputs
that count in binary code.
The 74LS92 pinouts are shown in Figure 4-101. Plug the chip into your bread-
board and make connections as shown in Figure 4-102. Initially, the 555 timer
will drive the counter in slow-motion, at around 1 step per second. Figure
4-103 shows the actual components on a breadboard.
Note that the counter has unusual power inputs, on pins 5 and 10 instead of
at the corners. Also four of its pins are completely unused, and do not connect
with anything inside the chip. Therefore, you don’t need to attach any wire to
them on the outside.

Chips, Ahoy! 215
No connection
No connection
No connection
Negative
to enable
Negative
to enable
No connection
Clock
input A
Binary
output A
Binary
output B
Clock
input B
Binary
output C
Binary
output D
74LS92
Counter
1
2
3
4
5
6
7
14
13
12
11
10
9
8
Figure 4-101. The unusual pin assignments include four that have no connection of any
kind inside the chip, and can be left unattached.
4K7
4K7
4K7
1K 1K
100K
10uF
Low-
Current
LEDs
0.1uF
5V DC regulated power supply
1 8
555
74LS92
Figure 4-102. This simple circuit uses a 555 timer running
slowly to control the 74LS92 binary counter and display the
succession of high states from its outputs.
Figure 4-103. The breadboard version of the schematic
in Figure 4-102 to display the outputs from a 74LS92
counter.

Chapter 4216
Now we come to the first new and difficult fact about the 74LSxx generation
ofTTL chips that makes them less desirable, for our purposes, than the 74HCxx
generation of CMOS chips that I have recommended in previous projects. The
modern and civilized HC chips will source 4mA or sink 4mA at each logical
output, but the older LS generation is fussier. It will sink around 8mA into each
output pin from a positive source, but when its output is high, it hardly gives
you anything at all. This is a very basic principle:
• Outputs from TTL logic chips are designed to sink current.
• They are not designed to source significant current.
In fact, the 74LS92 is rated to deliver less than half a milliamp. This is quite
acceptable when you’re just connecting it with another logic chip, but if you
want to drive an external device, it doesn’t provide much to work with.
The proper solution is to say to the chip,“All right, we’ll do it your way,”and set
things up with a positive source that flows through a load resistor to the LED
that you want to use, and from there into the output from the chip. This is the
“better”option shown in Figure 4-104.
Not
so good Better
1 14
74LSxx
series
logic
chip
1 14
74LSxx
series
logic
chip
Figure 4-104. Most TTL chips, including those in the LS generation, are unable to source
much current from their logical output pins (left) and should usually be wired to sink cur-
rent from a positive source (right).
The only problem is that now the LED lights up when the counter’s output is
low. But the counter is designed to display its output in high pulses. So your
LED is now off when it should be on, and on when it should be off.
You can fix this by passing the signal through an inverter, but already I’m get-
ting impatient with this inconvenience. My way around the problem, at least
for demo purposes, is to use the “Not so good” option in Figure 4-104 and
make it work by connecting a very-low-current LED with a large 4K7 load resis-
tor.This will enable us to“see”the output from the counter without asking it to
give more than its rated limit, and if you want to create a more visibly powerful

Chips, Ahoy! 217
display for a finished version of the dice circuit, I’ll deal with that later. Accord-
ing to my meter, the 4K7 resistor holds the current between 0.3mA and 0.4mA,
which is the counter’s rated maximum.
Set up your initial version of the circuit as shown in Figures 4-102 and 4-103. Be
careful when you wire the positive and negative power supply to the counter
chip, with its nonstandard pin assignments.
The 555 will run in astable mode, at about 1 pulse per second. This becomes
the clock signal for the counter.The first three binary outputs from the counter
then drive the three LEDs.
The counter advances when the input signal goes from high to low. So when
the LED beside the 555 timer goes out, that’s when the counter advances.
If you stare at the pattern generated by the outputs for long enough, you may
be able to see the logic to it, bearing in mind that its zero state is when they are
all off, and it counts up through five more steps before it repeats. The diagram
in Figure 4-105 shows this sequence. If you want to know why the pattern
works this way, check the following section,“Theory: Binary arithmetic.”
Theory
Binary arithmetic
The rule for binary counting is just a variation of the rule that we normally use
for everyday counting, probably without thinking much about it. In a 10-based
system, we count from 0 to 9, then carry 1 over to the next position on the left,
and go from 0 to 9 again in the right-most position. We repeat this procedure
until we get to 99, then carry a 1 over to a new position to make 100, and con-
tinue counting.
In binary we do the same thing, except that we restrict ourselves to digits 0 and
1 only. So begin with 0 in the rightmost position, and count up to 1. As 1 is our
limit, to continue counting we carry 1 over to the next place on the left, and
start again from 0 in the right-most position. Count up to 1, then add 1 to the
next place on the left—but, it already has a 1 in it, so it can’t count any higher.
So, carry 1 from there one space further, to the next place beside that—and so on.
If a glowing LED represents a 1, and a dark LED represents a 0, the diagram in
Figure 4-105 shows how the 74LS92 counts up from 0 to (decimal) 6 or (binary)
101 in its inimitable fashion. I’ve also included a diagram in Figure 4-106 show-
ing how a counter with four binary outputs would display decimal numbers
from 0 through 15, again using the LEDs to represent 1s and 0s.
Here’s a question for you: how many LEDs would you need to represent the
decimal number 1024 in binary? And how many for 1023?
Obviously binary code is ideally suited to a machine full of logic components
that either have a high or a low state. So it is that all digital computers use
binary arithmetic (which they convert to decimal, just to please us).
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
Figure 4-106. A hexadecimal (16-based)
binary counter would generate this suc-
cession of high states from its four output
pins as it counts from 0 through 15 in
decimal notation.
0 000
001
010
011
100
101
1
2
3
4
5
Figure 4-105. The three output pins of the
74LS92 counter have high states shown by
the red circles as the counter steps from
000 to 101 in binary notation.

Chapter 4218
Getting back to our project: I want to take the three binary outputs and make
them create patterns like the spots on a die. How can I do this? Quite easily, as
it turns out.
I’m assuming that I’ll use seven LEDs to simulate the patterns of spots on a
die. These patterns can be broken down into groups, which I have assigned to
the three outputs from the counter in Figure 4-108. The first output (farthest
to the right) can drive an LED representing the dot at the center of the die
face. The second (middle) output can drive two more diagonal LEDs. The third
output must switch on all four corner LEDs.
This will work for patterns 1 through 5, but won’t display the die pattern for a
6. Suppose I tap into all three outputs from the counter with a three-input NOR
gate. It has an output that goes high only when all three of its inputs are low,
so it will only give a high output when the counter is beginning with all-low
outputs. I can take advantage of this to make a 6 pattern.
Note that it’s bad practice to mix the LS generation of TTL chips with the HC
generation of CMOS chips, as their input and output ranges are different; so,
the NOR chip has to be a 74LS27, not a 74HC27.
We’re ready now for a simple schematic. In Figure 4-107 I’ve colored some of
the wires just to make it easier for you to distinguish them. The colors have no
other significance.
Figure 4-107. A simpli-
fied schematic shows
how outputs from the
74LS92 counter can
be combined, with
signal diodes and a
single three-input
NOR gate, to generate
the spot patterns on
a die. The wire colors
have no special mean-
ing and are used just
to distinguish them
from each other.
555
timer
ABC
74LS92 counter
Clock input
Binary outputs
NOR
D1
D2
4K7 each
D3 D4
Thegroupscombine
toformthesepatterns
Each of the three
counter outputs
lights these groups
Special
case to
create
a six
pattern
HI
HI
HI
HI
HI
LOLO
LO
LO
LO
LO
LO
LO
LO HI
LO
HI
LO
Figure 4-108. Binary outputs from the 74LS92
counter can be used to power LEDs arrayed
in groups to simulate the pattern of spots on
a die.

Chips, Ahoy! 219
Each of the LEDs is grounded through a separate 4K7 load resistor. Unfortu-
nately, this means that when they are displaying the pattern for a 6, all of them
are running in parallel from the output of the NOR gate, which overloads it.
As long as you don’t leave the display in this mode for very long periods, it
shouldn’t cause a problem. You could compensate by increasing the load re-
sistors, or by running pairs of the LEDs through one resistor, but this will make
them so dim that they’ll be difficult to see, as they’re so close to their lower
limit for current already.
Notice how I have added four signal diodes, D1 through D4. When Output C
goes high, it has to illuminate all four corner LEDs, and so its power goes into
the brown wire as well as the gray wire. But we must never allow one output
to feed back into another, so D4 is needed to protect Output B when Output
C is high.
Because there is now a connection between B and C, we need D2 to protect
Output C when Output B is high. And because Output B must only feed two
of the corner LEDs, we also need D3 to stop it from illuminating the other two.
And, we have to protect the output from the NOR gate when either Output C
or Output B is high. This requires D1.
Figure 4-109 shows everything that I’ve described so far assembled in bread-
board format, while Figure 4-110 shows the test version that I built. Note that
the unused logical inputs on the 74LS27 chip are shorted together and con-
nected to the positive side of the power supply. Here’s the rule:
• When using CMOS chips (such as the HC series), connect unused logical
inputs to the negative side of the power supply.
• When using TTL chips (such as the LS series), connect unused logical in-
puts to the positive side of the power supply.
I assume that you have had enough fun watching the LEDs count slowly, so
I’ve changed the capacitor and resistor values for the 555 to increase its speed
from approximately 1 pulse per second to about 50,000 pulses per second.
The counter could run much faster than this, but I just want it to cycle fast
enough so that when the user presses and releases a button, the count will
stop at an unforeseeable number.
The button starts and stops the 555 timer by applying and releasing power
to the timing circuit only. This is the equivalent of shaking and then throwing
the die.
While the counter is running fast, the LEDs are flashing so fast that all of them
will seem to be on at once. At the same time, the circuit charges a new 68 µF
capacitor, which I have added between the pushbutton and ground. When
you release the button, this capacitor discharges itself through the 1K timing
resistor. As the charge dissipates, the timing capacitor will take longer and
longer to charge, and discharge, and the frequency of the 555 will gradually
diminish. Consequently the LED display will also flash slower, like the reel on a
Las Vegas slot machine gradually coming to a stop. This increases the tension
as players can see the die display counting to the number that they’re hoping
for—and maybe going one step beyond it.
1K
1K68uF
1K
0.01uF
All above are 4K7
0.1uF
D1
D2
D3
D4
1 8
555
74LS92
74LS27
Figure 4-109. With some extra compo-
nents, the schematics from Figures 4-102
and 4-107 can be combined to make the
working dice simulation.

Chapter 4220
Note that to maximize this effect, the button has to be held down for a full
second or more, so that the 68 µF capacitor becomes fully charged before the
button is released.
So, this circuit now fulfills the original goal. But can it be better? Of course
it can.
Enhancements
The main thing I want to improve is the brightness of the LEDs. I could add a
transistor to amplify the current to each one, but there’s a simpler alternative:
a TTL“open collector”inverter.
I want to use an inverter because in the world ofTTL, as I mentioned earlier, we
can sink much more power into the output pin of a chip than we can source
from it. So, I’m going to turn each LED the other way around and connect their
load resistors to the positive side of the power supply. This way, they’ll sink
their power into the outputs of the inverter.
And the great advantage of an “open collector” version of the inverter chip is
that it is designed to sink much more current than a normal TTL logic chip. It is
rated for 40mA per pin. The only disadvantage is that it cannot source any cur-
rent at all; instead of its output going high, it just behaves like an open switch.
But that’s OK for this circuit.
So the next and final schematic, in Figure 4-111, includes the 74LS06 invert-
er, which has also been added to the breadboarded version shown in Figure
4-112. I suggest that you put aside the little low-current LEDs and substitute
some normal-size ones. Using Kingbright “standard” WP15031D 5mm LEDs, I
find that each draws almost exactly 20mA with a voltage drop of about 2V
with a 120 ohm series resistor. Because each output pin from the 74LS06 in-
verter powers no more than two LEDs at a time, this is exactly within its speci-
fication. I suggest that if you build this circuit, you check the consumption of
your particular choice of LEDs and adjust the resistors if necessary.
Remember: to measure the voltage drop across an LED, simply touch the
probes of your meter across it while it is illuminated. To measure the current,
disconnect one side of the LED and insert the meter, in milliamp mode, be-
tween the leg of the LED and the contact that it normally makes in the circuit.
For a really dramatic display, you can get some 1 cm diameter LEDs (Figure
4-113). Check the specification, and you should find that many of these don’t
use more power than the usual 5 mm type. But whatever kind you use, don’t
forget to turn them around so that their negative sides face toward the in-
verter, and their positive sides face the resistors, which are connected to the
positive side of the power supply.
One last detail: I had to add two 10K resistors to this version of the circuit. Can
you see why? Diodes D1 through D4 are designed to transmit positive voltage
through to the inverter when appropriate, but they prevent the inputs of the
inverter from“seeing”the negative side of the power supply when the counter
outputs are low. These inverter inputs require pull-down resistors to prevent
them from“floating”and producing erroneous results.
Figure 4-110. The electronic dice schematic
applied to a breadboard, with a pushbut-
ton at the top to start and stop the coun-
ter, and 7 LEDs at the bottom to display
the output.

Chips, Ahoy! 221
1K
1K
1K
0.01uF0.1uF
D1
D2
D3
D4
1 8
555
74LS92
74LS27
74LS06
Each
resistor
below
is 120
ohms
10K
10K
68uF
Figure 4-111. If open-collector inverters are added to the dice
schematic, it can drive full-size LEDs with up to 40mA, as long as
the LEDs are turned around to sink current into the TTL output
stage instead of trying to source current from it.
Figure 4-112. The completed circuit using an open-collector
inverter to drive full-size LEDs.

Chapter 4222
The final enhancements are up to you. Most obviously, you can add a second
die, as many games require two dice. The 74LS27 chip still has a couple of
spare NOR gates in it, one of which you can make use of, but you will need
an additional 555 timer, running at a significantly different speed to ensure
randomness, and it will have to drive a second counter.
After you get your dice up and running, you may want to test them for ran-
domness. Because the pulses from a 555 timer are of equal length, every num-
ber has an equal chance of coming up; but the longer you hold down the Start
button, the better your odds are of interrupting the counting process at a truly
random moment. Anyone using your electronic dice should be told that“shak-
ing”them for a full second is mandatory.
Of course, I could have simulated dice more easily by writing a few lines of
software to generate random numbers on a screen, but even a fancy screen
image cannot have the same appeal as a well-made piece of hardware. Figure
4-113 shows white 1 cm LEDs mounted in a sanded polycarbonate enclosure
for dramatic effect.
Most of all, I derived satisfaction from using simple, dedicated chips that dem-
onstrate the binary arithmetic that is fundamental in every computer.
Figure 4-113. The open-collector inverter chip in the dice circuit is sufficiently powerful to
drive 1-cm white LEDs that draw about 20mA each, using a potential of 2V. In this finished
version, the LEDs were embedded in cavities drilled from the underside of half-inch poly-
carbonate, which has been treated with an orbital sander to create a translucent finish.

Chips, Ahoy! 223
Experiment 24: Intrusion Alarm Completed
Now let me suggest how you can apply the knowledge from this chapter of
the book to upgrade the burglar alarm project that was last modified in Ex-
periment 15. You’ll probably need to check Chapters 2 and 3 to refamiliarize
yourself with some features of the alarm.
Upgrade 1: Delayed Activation
The biggest flaw in the alarm was that as soon as it was activated, it would im-
mediately respond to any signal from the door and window sensors. It needed
a feature to delay activation to give you a chance to exit from the building
before the alarm armed itself. A 555 timer can provide this functionality, prob-
ably in conjunction with a relay. The power to the alarm should pass through
the contacts of the relay, which are normally closed. When you press a button
on the timer, it sends a positive pulse to the relay lasting for around 30 sec-
onds, holding the relay open for that period. You could mount the timer in its
own little box with a button on it, which you press when you’re ready to leave
the building. The 12-volt power supply to the burglar alarm passes through
the box containing the delay circuit. For 30 seconds, the 555 interrupts power
to the alarm, and then restores it, ready for action.
Upgrade 2: Keypad Deactivation
This is now really simple. You can substitute a latching relay instead of the
switch, S1, on the alarm box (shown in Figure 3-110), and use a keypad to set
and reset the relay in exactly the same way as in the combination lock in Ex-
periment 20. You’ll have to run an additional three wires from the relay, out
of the alarm box, to the keypad (one supplying power to the “on” relay coil,
another supplying power to the“off”coil, the third being a common ground).
You can either use a 9-volt battery to power the electronics in association with
the keypad, or run an additional fourth wire from the alarm box, to carry posi-
tive power to the logic chips, bearing in mind that you have to insert a voltage
regulator at some point, to drop the 12 volts that the alarm uses to the 5 volts
that the logic gates require. As the gates consume so little power, the 12-to-
5 drop should be OK for the voltage regulator; it won’t have to dissipate too
much heat.
With this additional feature, you can use the alarm like this:
• Press the pound key on the keypad to flip the latching relay into its “on”
mode, so that it passes power to the alarm box, which is now armed.
• If you want to leave the house, push the button on the delay unit to give
you 30 seconds in which to do so.
• If the alarm is triggered, enter your secret code on the keypad to deacti-
vate it by flipping the latching relay to its“off”position and cutting power
to the alarm box.

Chapter 4224
These modifications are so simple that I think the block diagram in Figure
4-114 should be all you need. I don’t think I need to give you any schematics.
The only change you have to make to the existing alarm is to substitute the
latching relay for the on/off switch.
But, there is still one obvious necessary enhancement needed: how can you
get back into the house without instantly triggering the alarm?
Door and Window
Magnetic Switches
Transistor Sensor
and Self-Locking
Relay
1-Minute
Delay Circuit
Pushbutton
1-Minute
Power Interrupt
Test Button
Alarm Box
Noise
Maker
Latching
Alarm on/off RelayKeypad and
5V Logic Circuit
12V DC
Power
Supply
Figure 4-114. This block diagram shows the relative placement of the old and new compo-
nents. The pushbutton power interrupt (which allows you to leave the house before the
alarm switches itself back on) goes between the power supply and everything else.
The latching relay substitutes for the DPDT switch on the previous version of the alarm.
The transistor and self-locking relay, connected with the door and window magnetic
switches, remain unchanged. The new delay circuit is inserted between the self-locking
relay and the noisemaker. The test button is wired with the latching relay in the same way
that it was wired previously with the DPDT switch.

Chips, Ahoy! 225
Upgrade 3: Delay Before Deactivation
Typically, alarms include another delay feature.When you open a door on your
way into the building and it triggers the alarm, you have 30 seconds to deacti-
vate it, before it starts making a noise.
How can we implement this delay feature? If I try to use another 555 timer
to generate a pulse to inhibit the noise, that won’t work, because the output
from either the transistor or the relay can continue indefinitely. The relay locks
itself on, and the transistor can continue passing voltage for as long as some-
one leaves a door open. If either of these signals activates a timer in mono-
stable mode, the pulse from the timer will never end, and it will suppress the
alarm indefinitely.
I think what I have to do is use a resistor and a capacitor to create a delay.
I’ll power them through the existing relay, so that I can be sure that they’ll
receive the full voltage of the power supply, after beginning from zero. Gradu-
ally the capacitor will acquire voltage—but I can’t connect this directly to the
noisemaker, because the noisemaker will gradually get louder as the voltage
increases.
I have to insert a device that will be triggered to give full voltage when the
input rises past a certain point. To do this, I’ll use a 555 timer that’s wired in
bistable mode. This kind of modification is generally known as a “kludge,” be-
cause it’s not elegant, uses too many components, and does not use them
appropriately. What I really need is a comparator, but I don’t have space to get
into that topic. So, using the knowledge that you have so far, the schematic in
Figure 4-115 shows how a delay can be added to the alarm—not elegantly,
but reliably.
The only problem is that if you power up a 555 timer in bistable mode, there’s
a 50-50 chance that the timer starts itself with its output high or low. So I need
to pull the voltage low on the reset pin (to start the timer with its output inhib-
ited) and gradually let it become positive (to permit the output). At the same
time, I want to start with the voltage high on the trigger pin and gradually
lower it, until it falls below 1/3 of the power supply and triggers the output.
So there are two timing circuits.The one for the reset pin works faster than the
one on the trigger pin, so that at the point when the timer is triggered, the
reset won’t stop it.
The schematic shows component values that will do this. The 10 µF capacitor
starts low but is charged through the 10K resistor in a couple of seconds. The
timer is now ready to be triggered. But the 68 µF capacitor starts high (being
connected with the positive side of the power supply) and takes a full minute
to be pulled down to 1/3 of supply voltage through the 1M resistor. At that
point, its voltage is low enough to trigger the 555. The timer output goes high
and supplies the noisemaker.
You should be able to insert this little delay module in your alarm box, be-
tween the output from the relay and the input to the noisemaker without too
much trouble. And if you want to adjust the delay, just use a higher or lower
value resistor than 1M.

Chapter 4226
Q1
D1
R1
1K
10K
68uF
10K
1M
10uF
Power to
noise
maker
12V
DC
Switches
activated
by opened
doors or
windows
555
Figure 4-115. This addition to the original alarm circuit imposes a one-minute delay before
the alarm sounds. The 555 timer (wired in bistable mode) receives power through relay
R1. The lower timing circuit initially applies negative voltage to the reset, ensuring that
the 555 powers up with its output suppressed. This voltage quickly rises. Meanwhile the
upper timing circuit applies a voltage to the trigger that gradually diminishes as the 68
µF capacitor equalizes its charge through the 1M resistor. When the voltage diminishes to
1/3 of the supply, the timer’s output goes high and starts the noisemaker. If the power to
the circuit is interrupted at any time before this, the relay relaxes, the capacitors gradually
discharge, and the alarm does not sound.
The Wrap-Up
If you add these three enhancements, your alarm will have all the features on
my original wish list. Of course, if I were designing it from scratch, with all the
information that has been added in this chapter of the book, it could be more
elegant. But the modifications have not entailed making destructive changes
to our original project, and all the design goals have been met.

5
227
What Next?
At this point, we can branch out in numerous directions. Here are some
possibilities:
Audio electronics
This is a field in itself, including hobby projects, such as simple amplifiers
and“stomp boxes,”to modify guitar sound.
Radio-frequency devices
Anything that receives or transmits radio waves, from an ultra-simple AM
radio to remote controllers.
Motors
The field of robotics has encouraged the growth of many online sites sell-
ing stepper motors, gear motors, synchronous motors, servo motors, and
more.
Programmable microcontrollers
These are tiny computers on a single chip. You write a little program on
your desktop computer, which will tell the chip to follow a series of pro-
cedures, such as receiving input from a sensor, waiting for a fixed period,
and sending output to a motor. Then you download your program onto
the chip, which stores it in nonvolatile memory. Popular controllers in-
clude the PICAXE, BASIC Stamp, Arduino, and many more. The cheapest
ones retail for a mere $5 each.
Obviously, I don’t have space to develop all of these topics fully, so what I’m
going to do is introduce you to them by describing just one or two projects in
each category.You can decide which interests you the most, and then proceed
beyond this book by reading other guides that specialize in that interest.
I’m also going to make some suggestions about setting up a productive work
area, reading relevant books, catalogs, and other printed sources, and gener-
ally proceeding further into hobby electronics.
In this chapter
Customizing Your Work Area
Reference Sources
Experiment 25: Magnetism
Experiment 26: Tabletop Power Generation
Experiment 27: Loudspeaker Destruction
Experiment 28: Making a Coil React
Experiment 29: Filtering Frequencies
Experiment 30: Fuzz
No Power
Experiment 32: A Little Robot Cart
Experiment 33: Moving in Steps
Experiment 34: Hardware Meets Software
Experiment 35: Checking the Real World
Experiment 36: The Lock, Revisited
In Closing

Chapter 5228
Tools
You won’t need any new tools for this section of the book.
Supplies and Components
As we have progressed to the point where you may want to pick and choose
which projects you attempt, I will list the supplies and components at the be-
ginning of each experiment.
At this point, if you’re getting hooked on the fun of creating hardware but
haven’t allocated a permanent corner to your new hobby, I have some sug-
gestions. Having tried many different options over the years, my main piece of
advice is this: don’t build a workbench!
Many hobby electronics books want you to go shopping for 2×4s and ply-
wood, as if a workbench has to be custom-fabricated to satisfy strict criteria
about size and shape. I find this puzzling. To me, the exact size and shape of a
bench is not very important. I think the most important issue is storage.
I want tools and parts to be easily accessible, whether they’re tiny transistors
or big spools of wire. I certainly don’t want to go digging around on shelves
that require me to get up and walk across the room.
Figure 5-1. The ideal work area: surrounded by storage. Never again will you need to get
out of your chair!

What Next? 229
This leads me to two conclusions:
1. You need storage above the workbench.
2. You need storage below the workbench.
Many DIY workbench projects allow little or no storage underneath. Or, they
suggest open shelves, which will be vulnerable to dust. My minimum configu-
ration would be a pair of two-drawer file cabinets with a slab of 3/4-inch ply-
wood or a Formica-clad kitchen countertop placed across them. File cabinets
are ideal for storing all kinds of objects, not just files.
Of all the workbenches I’ve used, the one I liked best was an old-fashioned
steel office desk—the kind of monster that dates back to the 1950s. They’re
difficult to move (because of their weight) and don’t look beautiful, but you
can buy them cheaply from used office furniture dealers, they’re generous in
size, they withstand abuse, and they last forever. The drawers are deep and
usually slide in and out smoothly, like good file-cabinet drawers. Best of all,
the desk has so much steel in it that you can use it to ground yourself before
touching components that are sensitive to static electricity. If you use an anti-
static wrist strap, you can simply attach it to a sheet-metal screw that you drive
into one corner of the desk.
What will you put in the deep drawers of your desk or file cabinets? Some
paperwork may be useful, perhaps including the following documents:
• Product data sheets
• Parts catalogs
• Sketches and plans that you draw yourself
The remaining capacity of each drawer can be filled with plastic storage box-
es. The boxes can contain tools that you don’t use so often (such as a heat
gun or a high-capacity soldering iron), and larger-sized components (such as
loudspeakers, AC adapters, project boxes, and circuit boards). You should look
for storage boxes that measure around 11 inches long, 8 inches wide, and 5
inches deep, with straight sides. Boxes that you can buy at Wal-Mart will be
cheaper, but they often have tapering sides (which are not space-efficient).
The boxes that I like best are Akro-Grids, made by Akro-Mils (see Figures 5-2 and
5-3). These are very rugged, straight-sided, with optional transparent snap-on
lids.You can download the full Akro-Mills catalog from http://www.akro-mils.com
and then search online for retail suppliers. You’ll find that Akro-Mils also sells
an incredible variety of parts bins, but I don’t like open bins because their con-
tents are vulnerable to dust and dirt.
For medium-size components, such as potentiometers, power connectors, con-
trol knobs, and toggle switches, I like storage containers measuring about 11
inches long, 8 inches wide, and 2 inches deep , divided into four to six sections.
You can buy these from Michaels (the craft store), but I prefer to shop online for
thePlanobrand,astheyseemmoredurablyconstructed.ThePlanoproductsthat
are most suitable for medium-size electronic parts are classified as fishing-tackle
boxes, and you’ll see them at http://www.planomolding.com/tackle/products.asp.
Figure 5-2. Akro-Grid boxes contain
grooves allowing them to be partitioned
into numerous compartments for conve-
nient parts storage.
Figure 5-3. Lids are sold separately for
Akro-Grid boxes to keep the contents
dust-free. The height of the box in Figure
5-2 allows three to be stacked in a typical
file-cabinet drawer. The box shown here
allows two to be stacked.

Chapter 5230
For undivided, flat-format storage boxes, the Prolatch 23600-00 is ideally sized
to fit a file-cabinet drawer, and the latches are sufficiently secure that you
could stack a series of them on their long edges. See Figure 5-4.
Plano also sells some really nicely designed toolboxes, one of which you can
place on your desktop. It will have small drawers for easy access to screwdriv-
ers, pliers, and other basics. Because you need a work area that’s only about
three feet square for most electronics projects, surrendering some desk space
to a toolbox is not a big sacrifice.
If you have a steel desk with relatively shallow drawers, one of them can be al-
located for printed catalogs. Don’t underrate the usefulness of hard copy, just
because you can buy everything online. The Mouser catalog, for instance, has
an index, which is better in some ways than their online search feature, and
the catalog is divided into helpful categories. Many times I’ve found useful
parts that I never knew existed, just by browsing, which is much quicker than
flipping through PDF pages online, even with a broadband connection. Cur-
rently, Mouser is still quite generous about sending out their catalogs, which
contain over 2,000 pages. McMaster-Carr will also send you a catalog, but only
after you‘ve ordered from them, and only once a year.
Now, the big question: how to store all those dinky little parts, such as resistors,
capacitors, and chips? I’ve tried various solutions to this problem.The most ob-
vious is to buy a case of small drawers, each of which is removable, so you can
place it on your desk while you access its contents. But I don’t like this system,
for two reasons. First, for very small components, you need to subdivide the
drawers, and the dividers are never secure. And second, the removability of
the drawers creates the risk of accidentally emptying the contents on the floor.
Maybe you’re too careful to allow this to happen, but I’m not!
My personal preference is to use Darice Mini-Storage boxes, shown in Figure
5-5. You can find these at Michaels in small quantities, or buy them more eco-
nomically in bulk online from suppliers such as http://www.craftamerica.com.
The blue boxes are subdivided into five compartments that are exactly the
right size and shape for resistors. The yellow boxes are subdivided into ten
compartments, which are ideal for semiconductors. The purple boxes aren’t
divided at all, and the red boxes have a mix of divisions.
The dividers are molded into the boxes, so you don’t have the annoyance asso-
ciated with removable dividers that slip out of position, allowing components
to mix together. The box lids fit tightly, so that even if you drop one of the
boxes, it probably won’t open. The lids have metal hinges, and a ridge around
the edge that makes the boxes securely stackable.
I keep my little storage boxes on a set of shelves above the desk, with a gap of
3 inches between one shelf and the next, allowing two boxes to be stacked on
each shelf. If I want to work with a particular subset of boxes, I shift them onto
the desktop and stack them there.
Figure 5-4. This Plano brand box is
undivided, making it useful for storing
spools of wire or medium-size tools. When
stacked upright on its long edge, three will
fit precisely in a file-cabinet drawer.
Figure 5-5. Darice Mini-Storage boxes are
ideal for components such as resistors, ca-
pacitors, and semiconductors. The boxes
can be stacked stably or stored on shelves,
with their ends labeled. The brand sticker
is easily removed after being warmed with
a heat gun.

What Next? 231
Labeling
No matter which way you choose to store your parts, labeling them is essential.
Any ink-jet printer will produce neat-looking labels, and if you use peelable
(nonpermanent) labels, you’ll be able to reorganize your parts in the future, as
always seems to become necessary. I use color-coded labels for my collection
of resistors, so that I can compare the stripes on a resistor with the code on the
label, and see immediately if the resistor has been put in the wrong place. See
Figure 5-6.
Even more important: you need to place a second (non-adhesive) label inside
each compartment with the components. This label tells you the manufac-
turer’s part number and the source, so that reordering is easy. I buy a lot of
items from Mouser, and whenever I open their little plastic bags of parts, I snip
out the section of the bag that has the identifying label on it, and slide it into
the compartment of my parts box before I put the parts on top of it. This saves
frustration later.
If I were really well organized, I would also keep a database on my computer
listing everything that I buy, including the date, the source, the type of com-
ponent, and the quantity. But I’m not that well organized.
On the Bench
Some items are so essential that they should sit on the bench or desktop on
a permanent basis. These include your soldering iron(s), helping hands with
magnifier, desk lamp, breadboard, power strip, and power supply. For a desk
lamp, I prefer the type that has a daylight-spectrum fluorescent bulb, because
it spreads a uniform light and helps me to distinguish colors of adjacent stripes
on resistors.
The power supply is a matter of personal preference. If you’re serious about
electronics, you can buy a unit that delivers properly smoothed current at a
variety of properly regulated and calibrated voltages. Your little wall-plug unit
from RadioShack cannot do any of these things, and its output may vary de-
pending on how heavily you load it. Still, as you’ve seen, it is sufficient for basic
experiments, and when you’re working with logic chips, you need to mount a
5-volt regulator on your breadboard anyway. Overall, I consider a good power
supply optional.
Another optional item is an oscilloscope. This will show you, graphically, the
electrical fluctuations inside your wires and components, and by applying
probes at different points, you can track down errors in your circuit. It’s a neat
gadget to own, but it will cost a few hundred dollars, and for our tasks so far, it
has not been necessary. If you plan to get seriously into audio circuits, an oscil-
loscope becomes far more important, because you’ll want to see the shapes of
the waveforms that you generate.
You can try to economize on an oscilloscope by buying a unit that plugs into
the USB port of your computer and uses your computer monitor to display the
signal. I have tried one of these, and was not entirely happy with the results. It
worked, but did not seem accurate or reliable for low-frequency signals. May-
be I was unlucky; I decided not to try any other brands.
Figure 5-6. To check that resistors are not
placed in the wrong compartments, print
the color code on each label.

Chapter 5232
The surface of your desk or workbench will undoubtedly become scarred by ran-
dom scuffs, cut marks, and drops of molten solder. I use a piece of half-inch ply-
wood, two feet square, to protect my primary work area, and I clamp a miniature
vise to its edge.To reduce the risk of static electricity when working with sensitive
components, I cover the plywood with a square of conductive foam. This is not
cheap, but offers advantages in addition to protecting chips from being zapped.
Instead of scattering stray components, I can stick them into the foam, like plants
growing in a garden. And like a garden, I can divide it into sections, with resistors
on one side, capacitors on the other, and chips straight ahead.
Inevitably, during your work you’ll create a mess. Little pieces of bent wire, stray
screws, fasteners, and fragments of stripped insulation tend to accumulate, and
can be a liability. If metal parts or fragments get into a project that you’re build-
ing, they can cause short circuits. So you need a trash container. But it has to be
easy to use. I use a full-size garbage pail, because it’s so big that I can’t miss it
when I throw something toward it, and I can never forget that it’s there.
Last, but most essential: a computer. Now that all data sheets are available
online, and all components can be ordered online, and many sample circuits
are placed online by hobbyists and educators, I don’t think anyone can work
efficiently without quick Internet access.To avoid wasting space, I suggest you
use a small, cheap laptop that has a minimal footprint. A possible workbench
configuration, using a steel desk, is shown in Figure 5-7.
Figure 5-7. An old steel office desk can be
as good as, if not better than, a conven-
tional workbench when building small
electronics projects. It provides a large
work area and ample storage, and has
sufficient mass for you to ground yourself
when dealing with components that are
sensitive to static electricity.
Small
parts
boxes
Tool box
Helping
hands
Soldering
iron
Vise
Anti-static
foam
Plywood
Laptop
computer
Fluorescent
desk lamp
Power
strip

What Next? 233
Reference Sources
Reference Sources
Online
My favorite educational and reference site is Doctronics (http://www.doctronics.
co.uk). I like the way they draw their schematics, and I like the way they include
many illustrations of circuits on breadboards (which most sites don’t bother to
do). They also sell kits, if you’re willing to pay and wait for shipping from the UK.
Part of a page from the doctronics website is reproduced in Figure 5-8.
Figure 5-8. A sample page from http://www.doctronics.co.uk shows their detailed instruc-
tional approach. This is a valuable free online resource.
My next favorite hobby site is also British-based: the Electronics Club (http://
www.kpsec.freeuk.com). It’s not as comprehensive as Doctronics, but very
friendly and easy to understand.
For a more theory-based approach, try http://www.electronics-tutorials.ws.This
will go a little farther than the theory sections I’ve included here.
For an idiosyncratic selection of electronics topics, try Don Lancaster’s Guru’s
Lair (http://www.tinaja.com). Lancaster wrote The TTL Cookbook more than 30
years ago, which opened up electronics to at least two generations of hob-
byists and experimenters. He knows what he’s talking about, and isn’t afraid
of getting into some fairly ambitious areas such as writing his own PostScript
drivers and creating his own serial-port connections. You’ll find a lot of ideas
there.

Reference Sources
Chapter 5234
Books
Yes, you do need books. As you’re already reading this one, I won’t recommend
other beginners’guides. Instead, in keeping with the orientation of this chap-
ter, I’ll suggest some titles that will take you farther in various directions, and
can be used for reference. I own all of these myself, and find them valuable:
Practical Electronics for Inventors, by Paul Scherz (McGraw-Hill, Second Edition,
2007)
This is a massive, comprehensive book, well worth the $40 cover price.
Despite its title, you won’t need to invent anything to find it useful. It’s my
primary reference source, covering a wide range of concepts, from the
basic properties of resistors and capacitors all the way to some fairly high-
end math. If you buy only one book (in addition to this one, of course!),
this would be my recommendation.
Getting Started with Arduino, by Massimo Banzi (Make: Books, 2009)
If you enjoy the simplicity and convenience of the PICAXE programmable
microcontroller that I describe later in this chapter, you’ll find that the
Arduino can do a lot more. Getting Started is the simplest introduction
around, and will help to familiarize you with the Processing language
used in Arduino (similar to the C language, not much like the version of
BASIC used by the PICAXE).
Making Things Talk, by Tom Igoe (Make: Books, 2007)
This ambitious and comprehensive volume shows how to make the most
of the Arduino’s ability to communicate with its environment, even get-
ting it to access sites on the Internet.
TTL Cookbook, by Don Lancaster (Howard W. Sams Co, 1974)
The 1974 copyright date is not a misprint! You may be able to find some
later editions, but whichever one you buy, it will be secondhand and pos-
sibly expensive, as this title now has collectible value. Lancaster wrote his
guide before the 7400 series of chips was emulated on a pin-for-pin basis
by CMOS versions, but it’s still a good reference, because the concepts and
part numbers haven’t changed, and his writing is so accurate and concise.
CMOS Sourcebook, by Newton C. Braga (Sams Technical Publishing, 2001)
This book is entirely devoted to the 4000 series of CMOS chips, not the
74HC00 series that I’ve dealt with primarily here. The 4000 series is older
and must be handled more carefully, because it’s more vulnerable to stat-
ic electricity than the generations that came later. Still, the chips remain
widely available, and their great advantage is their willingness to tolerate
a wide voltage range, typically from 5 to 15 volts. This means you can set
up a 12-volt circuit that drives a 555 timer, and use output from the timer
to go straight into CMOS chips (for example). The book is well organized
in three sections: CMOS basics, functional diagrams (showing pinouts for
all the main chips), and simple circuits showing how to make the chips
perform basic functions.

What Next? 235
Reference Sources
The Encyclopedia of Electronic Circuits, by Rudolf F. Graf (Tab Books, 1985)
A totally miscellaneous collection of schematics, with minimal explana-
tions. This is a useful book to have around if you have an idea and want
to see how someone else approached the problem. Examples are often
more valuable than general explanations, and this book is a massive com-
pendium of examples. Many additional volumes in the series have been
published, but start with this one, and you may find it has everything you
need.
The Circuit Designer’s Companion, by Tim Williams (Newnes, Second Edition,
2005)
Much useful information about making things work in practical applica-
tions, but the style is dry and fairly technical. May be useful if you’re inter-
ested in moving your electronics projects into the real world.
The Art of Electronics, by Paul Horowitz and Winfield Hill (Cambridge University
Press, Second Edition, 1989)
The fact that this book has been through 20 printings tells you two things:
(1) Many people regard it as a fundamental resource; (2) Secondhand cop-
ies should be widely available, which is an important consideration, as the
list price is over $100. It’s written by two academics, and has a more tech-
nical approach than Practical Electronics for Inventors, but I find it useful
when I’m looking for backup information.
Getting Started in Electronics, by Forrest M. Mims III (Master Publishing, Fourth
Edition, 2007)
Although the original dates back to 1983, this is still a fun book to have. I
think I have covered many of its topics here, but you may benefit by read-
ing explanations and advice from a completely different source, and it
goes a little farther than I have into some electrical theory, on an easy-to-
understand basis, with cute drawings. Be warned that it’s a brief book with
eclectic coverage. Don’t expect it to have all the answers.
Figure 5-9. These books from MAKE provide
guidance if you want to go beyond basic micro-
controllers into the more exotic realms of the
Arduino chip.
Figure 5-10. A sun-damaged copy of the Don Lancaster’s
classic TTL Cookbook, a 2,000-page catalog from the
Mouser Electronics supply company, and two com-
prehensive reference books that can provide years of
additional guidance in all areas of electronics.

Chapter 5236
This experiment should be a part of any school science class, but even if you
remember doing it, I suggest that you do it again, because setting it up takes
only a matter of moments, and it’s going to be our entry point to a whole new
topic: the relationship between electricity and magnetism. Quickly this will
lead us into audio reproduction and radio, and I’ll describe the fundamentals
of self-inductance, which is the third and final basic property of passive com-
ponents (resistance and capacitance being the other two). I left self-inductance
until last because it’s not very relevant to the experiments that you’ve done
so far. But as soon as we start dealing with analog signals that fluctuate, it
becomes essential.
You will need:
• Large screwdriver.
• 22-gauge wire (or thinner). Quantity: 6 feet.
• AA battery.
Procedure
This couldn’t be simpler. Wind the wire around the shaft of the screwdriver,
near its tip. The turns should be neat and tight and closely spaced, and you’ll
need to make 100 of them, within a distance of no more than 2 inches. To fit
them into this space, you’ll have to make turns on top of previous turns. If the
final turn tends to unwind itself (which will happen if you’re using stranded
wire), secure it with a piece of tape. See Figure 5-11.
Now apply a battery, as shown in Figure 5-12. At first sight, this looks like a
very bad idea, because you’re going to short out your battery just as you did in
Experiment 2. But by passing the current through a wire that’s coiled instead
of straight, we’ll get some work out of it before the battery expires.
Put a small paper clip near the screwdriver blade, on a soft, smooth surface
that will not present much friction. A tissue works well. Because many screw-
drivers are already magnetic, you may find that the paper clip is naturally
attracted to the tip of the blade. If this happens, move the clip just outside
the range of attraction. Now apply the 1.5 volts to the circuit, and the clip
should jump to the tip of the screwdriver. Congratulations: you just made an
electromagnet.
Figure 5-12. A schematic can’t get much simpler than this.
Fundamentals
A two-way relationship
Every electric motor that was ever
made uses some aspect of the
relationship between electricity
and magnetism. It’s absolutely
fundamental in the world around
us. Remember that electricity can
create magnetism:
When electricity flows through a
wire, it creates a magnetic force
around the wire.
The principle works in reverse: mag-
netism can create electricity.
When a wire moves through a
magnetic field, it creates a flow of
electricity in the wire.
This second principle is used in
power generation. A diesel engine,
or a water-powered turbine, or a
windmill, or some other source of
energy either turns coils of wire
through a powerful magnetic
field, or turns magnets amid some
massive coils of wire. Electricity is
induced in the coils. In the next
experiment, you’ll see a dramatic
mini-demo of this effect.
Figure 5-11. Anyone who somehow missed
this most basic childhood demo of electro-
magnetism should try it just for the fun of
proving that a single AA battery can move
a paper clip.

What Next? 237
Theory
Inductance
When electricity flows through a wire, it creates a magnetic
field around the wire. Because the electricity“induces”this
effect, it is known as inductance. The effect is illustrated in
Figure 5-13.
Figure 5-13. When the flow of electricity is from left to right
along this conductor, it induces a magnetic force shown by the
green arrows.
The field around a straight wire is very weak, but if we bend
the wire into a circle, the magnetic force starts to accumu-
late, pointing through the center of the circle, as shown in
Figure 5-14. If we add more circles, to form a coil, the force
accumulates even more. And if we put a magnetic object
(such as a screwdriver) in the center of the coil, the effective-
ness increases further.
Figure 5-14. When the conductor is bent to form a circle, the cu-
mulative magnetic force acts through the center of the circle,
as shown by the large arrow.
Here’s an approximated formula showing the relationship
between the diameter of the coil, the width of the coil from
end to end, the number of turns, and its inductance. The
letter L is the symbol for inductance, even though the unit
is the Henry, named after an American electrical pioneer
named Joseph Henry:
L (in microHenrys) =
[(D × D) × (N x N)] / [(18 × D) + (40 × W)]
(Approximately)
In this formula, D is the diameter of the coil, N is the number
of turns, and W is the width of the coil from end to end. See
Figure 5-15. Here are three simple conclusions from this
formula:
• Inductance increases with the diameter of the coil.
• Inductance increases with the square of the number of
turns. (In other words, three times as many turns create
nine times the inductance.)
• If the number of turns remains the same, inductance is
lower if you wind the coil so that it’s slender and long,
but is higher if you wind it so that it’s fat and short.
W
=
W
idth
of coil
D=Diameter
of coil
N=Number
of turns of
wire
Figure 5-15. The inductance of a coil increases with its diameter
and with the square of its number of turns. If all other param-
eters remain the same, reducing the width (the distance from
end to end) by packing the turns more tightly will increase the
inductance.

Chapter 5238
Background
Joseph Henry
Born in 1797, Joseph Henry was the first to develop and demonstrate powerful
electromagnets. He also originated the concept of“self-inductance,”meaning
the“electrical inertia”that is a property of a coil of wire.
Henry started out as the son of a day laborer in Albany, New York. He worked in
a general store before being apprenticed to a watchmaker, and was interested
in becoming an actor. Friends persuaded him to enroll at the Albany Academy,
where he turned out to have an aptitude for science. In 1826, he was appointed
Professor of Mathematics and Natural Philosophy at the Academy, even though
he was not a college graduate and described himself as being“principally self-
educated.”Michael Faraday was doing similar work in England, but Henry was
unaware of it.
Henry was appointed to Princeton in 1832, where he received $1,000 per year
and a free house. When Morse attempted to patent the telegraph, Henry testi-
fied that he was already aware of its concept, and indeed had rigged a system
on similar principles to signal his wife, at home, when he was working in his
laboratory at the Philosophical Hall.
Henry taught chemistry, astronomy, and architecture, in addition to physical
science, and because science was not divided into strict specialties as it is now,
he investigated phenomena such as phosphorescence, sound, capillary action,
and ballistics. In 1846, he headed the newly founded Smithsonian Institution as
its secretary.
Figure 5-17. Joseph Henry was an American experimenter who pioneered the inves-
tigation of electromagnetism. This photograph is archived in Wikimedia Commons.
Fundamentals
Coil schematics and
basics
Check the schematic symbols for
coils in Figure 5-16. Note that if a
coil has an iron core, this is shown
with an extra couple of lines
(sometimes only one line). If it has
a ferrite core, the line is sometimes
shown with dashes.
An iron core will add to the
inductance of a coil, because it
increases the magnetic effect.
A coil in isolation does not gener-
ally have any polarity. You can con-
nect it either way around, but the
magnetic force will be reversed ac-
cordingly (coils that interact with
stuff—such as in transformers and
solenoids—do have polarity).
Perhaps the most widespread
application of coils is in transform-
ers, where alternating current
in one coil induces alternating
current in another, often sharing
the same iron core. If the primary
(input) coil has half as many turns
as the secondary (output) coil, the
voltage will be doubled, at half
the current—assuming hypotheti-
cally that the transformer is 100%
efficient.
Figure 5-16. Schematic diagrams
represent coils. At far right is the
older style. The third and fourth
symbols indicate that the coil is
wound around a solid or powdered
magnetic core, respectively.

What Next? 239
If you have just three components, you can see magnetism generating elec-
tricity right in front of you, right now.
You will need:
• Cylindrical neodymium magnet, 3/4-inch diameter, axially magnetized.
Quantity: 1. (Obtainable online at sites such as http://www.kjmagnetics.com.)
• Spool of hookup wire, 26-gauge, 100 feet. Quantity: 1.
• Spool of magnet wire, quarter-pound, 26-gauge, about 350 feet. Quan-
tity: 1. (Search online for sources for“magnet wire.”)
• Generic LED. Quantity: 1.
• 100 μF electrolytic capacitor. Quantity: 1.
• Signal diode, 2N4001 or similar. Quantity: 1.
• Jumper wires with alligator clips on the ends. Quantity: 2.
Procedure
You may be able to make this experiment work with the spool of hookup wire,
depending on the size of the spool relative to the size of your magnet, but as
the results are more likely to be better with the magnet wire, I’ll assume that
you’re using that—initially, at least. The advantage of the magnet wire is that
its very thin insulation allows the coils to be closely packed, increasing their
inductance.
First peek into the hollow center of the spool to see if the inner end of the
wire has been left accessible, as is visible in Figures 5-18 and 5-19. If it hasn’t,
you have to unwind the wire onto any large-diameter cylindrical object, then
rewind it back onto the spool, this time taking care to leave the inner end stick-
ing out.
Scrape the transparent insulation off each end of the magnet wire with a utility
knife or sandpaper, until bare copper is revealed. To check, attach your meter,
set to measure ohms, to the free ends of the wire. If you make a good contact,
you should measure a resistance of 30 ohms or less.
Place the spool on a nonmagnetic, nonconductive surface such as a wooden,
plastic, or glass-topped table. Attach the LED between the ends of the wire
using jumper wires. The polarity is not important. Now take a cylindrical neo-
dymium magnet of the type shown in Figure 5-20 and push it quickly down
into the hollow core, then pull it quickly back out. See Figure 5-21. You should
see the LED blink, either on the down stroke or the up stroke.
The same thing may or may not happen if you use 100 feet of 26-gauge hook-
up wire. Ideally, your cylindrical magnet should fit fairly closely in the hollow
center of the spool. If there’s a big air gap, this will greatly reduce the effect of
the magnet. Note that if you use a weaker, old-fashioned iron magnet instead
of a neodymium magnet, you may get no result at all.
Figure 5-18. An everyday 100-foot spool of
hookup wire is capable of demonstrating
the inductive power of a coil.
Figure 5-19. Magnet wire has thinner
insulation than hookup wire, allowing the
turns to be more densely packed, inducing
a more powerful magnetic field.

Chapter 5240
Figure 5-20. Three neodymium magnets,
1/4-, 1/2-, and 3/4-inch in diameter. I
would have preferred to photograph them
standing half-an-inch apart, but they
refused to permit it.
Figure 5-21. By moving a magnet vigor-
ously up and down through the center of a
coil, you generate enough power to make
the LED flash brightly.
Here’s another thing to try. Disconnect the LED and connect a 100 μF elec-
trolytic capacitor in series with signal diode, as shown in Figure 5-23. Attach
your meter, measuring volts, across the capacitor. If your meter has a manual
setting for its range, set it to 20V DC. Make sure the positive (unmarked) side
of the diode is attached to the negative (marked) side of the capacitor, so that
positive voltage will pass through the capacitor and then through the diode.
Now move the magnet vigorously up and down in the coil. The meter should
show that the capacitor is accumulating charge, up to about 10 volts. When
you stop moving the magnet, the voltage reading will gradually decline, most-
ly because the capacitor discharges itself through the internal resistance of
your meter.
This experiment is more important than it looks. Bear in mind that when you
push the magnet into the coil, it induces current in one direction, and when
you pull it back out again, it induces current in the opposite direction. You are
actually generating alternating current.
The diode only allows current to flow one way through the circuit. It blocks
the opposite flow, which is how the capacitor accumulates its charge. If you
jump to the conclusion that diodes can be used to change alternating current
to direct current, you’re absolutely correct. We say that the diode is“rectifying”
the AC power.
Experiment 24 showed that voltage can create a magnet. Experiment 25 has
shown that a magnet can create voltage. We’re now ready to apply these con-
cepts to the detection and reproduction of sound.
Blood Blisters and Dead Media
Neodymium magnets can be
hazardous. They’re brittle and can
shatter if they slam against a piece of
magnetic metal (or another magnet).
For this reason, many manufacturers
advise you to wear eye protection.
Because a magnet pulls with increas-
ing force as the distance between it
and another object gets smaller, it
closes the final gap very suddenly
and powerfully. You can easily pinch
your skin and get blood blisters.
If there’s an object made of iron or
steel anywhere near a neodymium
magnet, the magnet will find it and
grab it, with results that may be
unpleasant, especially if the object
has sharp edges and your hands are
in the vicinity. When using a magnet,
create a clear area on a nonmagnetic
surface, and watch out for magnetic
objects underneath the surface. My
magnet sensed a steel screw embed-
ded in the underside of a kitchen
countertop, and slammed itself
into contact with the countertop
unexpectedly.
Be aware that magnets create mag-
nets. When a magnetic field passes
across an iron or steel object, the
object picks up some magnetism of
its own. Be careful not to magnetize
your watch!
Don’t use magnets anywhere near a
computer, a disk drive, credit cards
with magnetic stripes, cassettes of
any type, and other media. Also keep
magnets well away from TV screens
and video monitors (especially
cathode-ray tubes). Last but not
least, powerful magnets can interfere
with the normal operation of cardiac
pacemakers.

What Next? 241
Figure 5-22. Because inductance increases with the diameter of a coil and with the square
of the number of turns, your power output from moving a magnet through the coil can
increase dramatically with scale. Those wishing to live “off the grid” may consider this
steam-powered configuration, suitable for powering a three-bedroom home.
Volts
Long Wire
(positive)
Figure 5-23. Using a diode in series with a capacitor, you can charge the capacitor with the
pulses of current that you generate by moving the magnet through the center of the coil.
This demo illustrates the principle of rectifying alternating current.

Chapter 5242
I’d like you to sacrifice a 2-inch loudspeaker, even though it means wasting the
$5 or so that it probably costs. Actually, I don’t consider this a waste, because
if you want to learn how a component works, there’s no substitute for actually
seeing inside it. You might also have such a speaker already, part of a piece of
cast-off personal electronics or toy you have in your basement.
You will need:
• Cheapest possible 2-inch loudspeaker. Quantity: 1. Figure 5-24 shows a
typical example.
Procedure
Turn the loudspeaker face-up (as shown in Figure 5-25) and cut around the
edge of its cone with a sharp utility knife or X-Acto blade. Then cut around
the circular center and remove the ring of black paper that you’ve created.
The result should look like Figure 5-26: you should see the flexible neck of the
loudspeaker, which is usually made from a yellow weave. If you cut around its
edge, you should be able to pull up the hidden paper cylinder, which has the
copper coil of the loudspeaker wound around it. In Figure 5-27, I’ve turned it
over so that it is easily visible. The two ends of this copper coil normally re-
ceive power through two terminals at the back of the speaker. When it sits in
the groove visible between the inner magnet and the outer magnet, the coil
reacts to voltage fluctuations by exerting an up-and-down force in reaction
to the magnetic field. This vibrates the cone of the loudspeaker and creates
sound waves.
Large loudspeakers in your stereo system work exactly the same way.They just
have bigger magnets and coils that can handle more power (typically, as much
as 100 watts).
Whenever I open up a small component like this, I’m impressed by the preci-
sion and delicacy of its parts, and the way it can be mass-produced for such a
low cost. I imagine how astonished the pioneers of electrical theory (such as
Faraday and Henry) would be, if they could see the components that we take
for granted today. Henry spent days and weeks winding coils by hand to create
electromagnets that were far less efficient than this cheap little loudspeaker.
Figure 5-25. Loudspeaker ready for creative
destruction.
Figure 5-26. The cone has been removed. Figure 5-27. The neck of the cone has been
pulled out. Note the coil of copper wire,
which fits precisely in the groove between
two magnets in the base of the speaker.
Figure 5-24. A 2-inch loudspeaker can be
instructively destroyed with a utility knife
or X-Acto blade.

What Next? 243
Background
Origins of loudspeakers
Loudspeakers utilize the fact that if you run a varying electrical current through
a coil situated in a magnetic field, the coil will move in response to the current.
This idea was introduced in 1874 by Ernst Siemens, a prolific German inven-
tor. (He also built the world’s first electrically powered elevator in 1880.) Today,
Siemens AG is one of the largest electronics companies in the world.
When Alexander Graham Bell patented the telephone in 1876, he used Siemen’s
concept to create audible frequencies in the earpiece. From that point on,
sound-reproduction devices gradually increased in quality and power, until
Chester Rice and Edward Kellogg at General Electric published a paper in 1925
establishing basic principles that are still used in loudspeaker design today.
At http://www.radiolaguy.com/Showcase/Gallery-HornSpkr.htm you’ll find
photographs of very beautiful early loudspeakers, which used a horn design
to maximize efficiency. As sound amplifiers became more powerful, speaker
efficiency became less important compared with quality reproduction and low
manufacturing costs. Today’s loudspeakers convert only about 1% of electrical
energy into acoustical energy.
Figure 5-28. This beautiful Amplion AR-114x illustrates the efforts of early design-
ers to maximize efficiency in an era when the power of audio amplifiers was very
limited. Photos by “Sonny, the RadiolaGuy.” Many early speakers are illustrated at
www.radiolaguy.com. Some are for sale.

Chapter 5244
Theory
Sound, electricity, and sound
Time now to establish a clear idea of how sound is transformed into electricity
and back into sound again.
Suppose someone bangs a gong with a stick. The flat metal face of the gong
vibrates in and out, creating sound waves. A sound wave is a peak of higher air
pressure, followed by a trough of lower air pressure.
The wavelength of the sound is the distance (usually ranging from meters to
millimeters) between one peak of pressure and the next peak.
The frequency of the sound is the number of waves per second, usually ex-
pressed as hertz.
Suppose we put a very sensitive little membrane of thin plastic in the path of
the pressure waves. The plastic will flutter in response to the waves, like a leaf
fluttering in the wind. Suppose we attach a tiny coil of very thin wire to the
back of the membrane so that it moves with the membrane, and let’s posi-
tion a stationary magnet inside the coil of wire. This configuration is like a tiny,
ultra-sensitive loudspeaker, except that instead of electricity producing sound,
it is configured so that sound produces electricity. Sound pressure waves make
the membrane move to and fro along the axis of the magnet, and the magnetic
field creates a fluctuating voltage in the wire.
This is known as a moving-coil microphone. There are other ways to build a
microphone, but this is the configuration that is easiest to understand. Of
course, the voltage that it generates is very small, but we can amplify it using
a transistor, or a series of transistors. Then we can feed the output through the
coil around the neck of a loudspeaker, and the loudspeaker will recreate the
pressure waves in the air. Figures 5-29 through 5-32 illustrate this sequence.
PRESSURE
TIME
Waves
of air
pressure
traveling
at the
speed of
sound
Figure 5-29. Step 1 in the process of converting sound to electricity, and back again.
When the hammer hits the gong, the face of the gong vibrates, creating pressure
waves that travel through the air.

What Next? 245
Theory
Sound, electricity, and sound (continued)
Somewhere along the way, we may want to record the sound and then replay
it. But the principle remains the same. The hard part is designing the micro-
phone, the amplifier, and the loudspeaker so that they reproduce the waveforms
accurately at each step. It’s a significant challenge, which is why accurate sound
reproduction can be elusive.
Time now to think about what happens inside the wire when it generates a
magnetic field. Obviously, some of the power in the wire is being transformed
into magnetic force. But just what exactly is going on?
VOLTAGE
TIME
MOVING-COIL
MICROPHONE
Figure 5-30. Step 2: the pressure waves penetrate the perforated shell of a micro-
phone and cause a diaphragm to vibrate in sympathy. The diaphragm has a coil
attached to it. When the coil vibrates to and fro, a magnet at its center induces
alternating current.
VOLTAGE
AMPLIFIER
Figure 5-31. Step 3: the tiny signals from the microphone pass through an amplifier,
which enlarges their amplitude while retaining their frequency and the shape of
their waveform.
LOUDSPEAKER
VOLTAGE
Waves
of air
pressure
traveling
at the
speed of
sound
Figure 5-32. Step 4: the amplified electrical signal is passed through a coil around
the neck of a loudspeaker cone. The magnetic field induced by the current causes
the cone to vibrate, reproducing the original sound.

Chapter 5246
A capacitor will absorb some DC current until it is fully charged, at which point
it blocks the flow. There’s another phenomenon that I haven’t mentioned so
far, which is the exact opposite of capacitance. It’s known as self-inductance,
and you find it in any coil of wire. Initially it blocks DC current (it reacts against
it), but then its opposition gradually disappears. Here are a few definitions:
Resistance
Constrains current flow and drops voltage.
Capacitance
Allows current to flow initially and then blocks it. This behavior is properly
known as capacitive reactance.
Self-Inductance
Blocks the flow of current initially and then allows it. This is also often re-
ferred to as inductive reactance. In fact, you may find the term“reactance”
used as if it means the same thing, but since self-inductance is the correct
term, I’ll be using it here.
In this experiment, you’ll see self-inductance in action.
You will need:
• LEDs, low-current type. Quantity: 2.
• Spool of hookup wire, 26-gauge, 100 feet. Quantity: 1.
• Resistor, 220Ω, rated 1/4 watt or higher. Quantity: 1.
• Capacitor, electrolytic, 2,000 μF or larger. Quantity: 1.
• SPST tactile switch. Quantity: 1.
Procedure
Take a look at the schematic in Figure 5-33. At first it may not make much
sense. The curly symbol is a coil of wire—nothing more than that. So appar-
ently the voltage will pass through the 220Ω resistor, and then through the
coil, ignoring the two LEDs, because the coil obviously has a much lower resis-
tance than either of them (and one of them is upside-down anyway).
Is that what will happen? Let’s find out. The coil can be a spool of 100 feet of
26-gauge (or smaller) hookup wire, although the spool of magnet wire listed
in Experiment 25 will work better, if you have that. Once again, you will need
access to both ends of the wire, and if the inner end is inaccessible, you’ll need
to rewind the coil, leaving the end sticking out.
Now that you have a coil, you can hook it up on your breadboard as shown in
Figure 5-34, where the green circle is a tactile switch and the two circular red
objects are LEDs. Make sure that you use low-current LEDs (otherwise, you
may not see anything) and make sure that one of them is negative-side-up,
positive-side-down and the other is positive-side-up, negative-side-down.
Also, the 220Ω resistor should be rated at 1/4 watt or higher, if possible (see
the following caution).
12V
DC
220
D1
D2
Figure 5-33. In this demonstration of self-
inductance, D1 and D2 are light-emitting
diodes. When the switch is closed, D1
flashes briefly because the coil obstructs
the initial flow of electricity. When the
switch is opened, D2 flashes as the col-
lapsing magnetic field induced by the coil
releases another short burst of current.

What Next? 247
12V
DC
Figure 5-34. The breadboarded version of the schematic in Figure 5-33 shows a simple
way to set it up for a quick demo. The green button is a tactile switch. The two red LEDs
should be placed so that the polarity of one is opposite to the polarity of the other.
When you press the button, one LED should flash briefly.When you release the
button, the other LED should flash.
What’s happening here? The coil possesses self-inductance, which means that
it reacts against any sudden change in the flow of electricity. First it fights it,
and during that brief moment, it blocks most of the current. Consequently, the
current looks for an alternative path and flows through D1, the lefthand LED
in the schematic. (D2 doesn’t respond, because it can pass current only in the
opposite direction.)
Meanwhile, the voltage pressure overcomes the coil’s self-inductance. When
the self-inductance disappears, the resistance of the coil is no more than 10
ohms—so now the electricity flows mostly through the coil, and because the
LED receives so little, it goes dark.
When you disconnect the power, the coil reacts again. It fights any sudden
changes. After the flow of electricity stops, the coil stubbornly sustains it for a
moment, because as the magnetic field collapses, it is turned back into elec-
tricity. This residual flow of current depletes itself through D2, the LED on the
right.
In other words, the coil stores some energy in its magnetic field. This is similar
to the way a capacitor stores energy between two metal plates, except that
the coil blocks the current initially and then lets it build up, whereas the ca-
pacitor sucks up current initially, and then blocks it.
The more turns of wire you have in your coil, the more self-inductance the coil
will have, causing your LEDs to flash more brightly.
Hot Resistors
You’ll be passing about 50mA
through the 220Ω resistor, while
the current is flowing. At 12 volts,
this works out at 0.6 watts. If you
use a 1/8-watt resistor, you will be
overloading it, and it will get quite
hot and may burn out. If you use a
1/4-watt resistor, it will still get hot,
but is unlikely to burn out, as long as
you don’t press the button for more
than a second or two.
Don’t run the circuit without the coil
of wire; you’ll be trying to pass more
than 50mA through the LEDs.

Chapter 5248
Here’s one last variation on this experiment to test your understanding of elec-
trical fundamentals. Remove the 220Ω resistor, and substitute a 1K resistor (to
protect your LED from sustained current). Remove the coil, and substitute a
very large capacitor—ideally, about 4,700 μF. (Be careful to get its polarity the
right way around.) What will you see when you press the button? Note that
you will have to hold it down for a couple of seconds to get a result. And what
will you see when you release the button? Remember: the behavior of capaci-
tance is opposite to the behavior of self-inductance.
Theory
Alternating current concepts
Here’s a simple thought experiment. Suppose you set up a 555 timer to send a
stream of pulses through a coil. This is a primitive form of alternating current.
We might imagine that the self-inductance of the coil will interfere with the
stream of pulses, depending how long each pulse is, and how much inductance
the coil has. If the pulses are too short, the self-inductance of the coil will tend
to block them. Maybe if we can time the pulses exactly right, they’ll synchronize
with the time constant of the coil. In this way, we can“tune”a coil to allow a
“frequency”to pass through it.
What happens if we substitute a capacitor? If the pulses are too long, compared
with the time constant of the capacitor, it will tend to block them, because it
will have enough time to become fully charged. But if the pulses are shorter, the
capacitor can charge and discharge in rhythm with the pulses, and will seem to
allow them through.
I don’t have space in this book to get deeply into alternating current. It’s a vast
and complicated field where electricity behaves in strange and wonderful ways,
and the mathematics that describe it can become quite challenging, involving
differential equations and imaginary numbers. However, we can easily demon-
strate the audio filtering effects of a loudspeaker and a coil.

What Next? 249
In this experiment, you’ll see how self-inductance and capacitance can be
used to filter audio frequencies. You’re going to build a crossover network: a
simple circuit that sends low frequencies to one place and high frequencies
to another.
You will need:
• Loudspeaker, 8Ω, 5 inches in diameter. Quantity: 1. Figure 5-35 shows a
typical example.
• Audio amplifier, STMicroelectronics TEA2025B or similar. Quantity: 1. See
Figure 5-36.
Figure 5-35. To hear the effects of audio
filters using coils and capacitors, you’ll
need a loudspeaker capable of reproduc-
ing lower frequencies. This 5-inch model is
the minimum required.
Figure 5-36. This single chip contains a
stereo amplifier capable of delivering a
total of 5 watts into an 8Ω speaker when
the two channels are combined.
Figure 5-37. A nonpolarized electrolytic
capacitor, also known as a bipolar capaci-
tor, looks just like an electrolytic capaci-
tor, except that it will have “NP” or “BP”
printed on it.
• Nonpolarized electrolytic capacitors (also known as bipolar). 47 μF. Quan-
tity: 2. A sample is shown in Figure 5-37. They should have “NP” or “BP”
printed on them to indicate“nonpolarized”or“bipolar.”
• Nonpolarized electrolytic capacitors (also known as bipolar). 100 μF.
Quantity: 5. (Because you’ll be working with audio signals that alternate
between positive and negative, you can’t use the usual polarized electro-
lytic capacitors. If you want to avoid the trouble and expense of ordering
nonpolarized capacitors, you can substitute two regular electrolytics in
series, facing in opposite directions, with their negative sides joined in the
middle. Just remember that when you put capacitors in series, their to-
tal capacitance is half that of each individual component. Therefore, you
would need two 220 μF electrolytics in series to create 110 μF of capaci-
tance. See Figure 5-38.)
• Potentiometer, with audio taper if possible. 100K. Quantity: 1.
• Coil, for crossover network. Quantity: 1. You can search a source such
as eBay for keywords “crossover” and “coil,” but if you can’t find one at a
reasonable price, you can make do with a spool of 100 feet of 20-gauge
hookup wire.
• Plastic shoebox. Quantity: 1.
220uF
100uF
220uF
Figure 5-38. You can make a nonpolar-
ized electrolytic capacitor by putting two
regular electrolytics in series. (In fact,
that’s what you’d find if you opened a real
nonpolarized capacitor.) The symbol at the
bottom is roughly equivalent to the pair of
symbols at the top; bear in mind that two
capacitors in series have a total capaci-
tance that is half that of each of them.

Chapter 5250
Procedure
The purpose of the audio amplifier chip is to provide enough power to get
a decent amount of sound out of your loudspeaker. The purpose of using a
5-inch speaker is to enable you to hear lower-frequency sounds than the baby
speakers that we have used previously. Bass notes have long wavelengths that
small speakers are not able to generate effectively.
Maybe you remember from building the intrusion alarm that a speaker makes
much more noise if you prevent the sound waves from the back of the cone
from cancelling the sound waves from the front of the cone. The obvious way
to achieve this is by enclosing the speaker in a box. I suggest a plastic box,
because they’re cheap, and we don’t care too much about sound quality as
long as we can hear at least some of the low frequencies. Figure 5-39 shows
the speaker bolted into the bottom of a plastic box, and Figure 5-40 shows the
box turned upside-down after snapping its lid into place.
Normally, a speaker should be mounted in a cabinet of heavy, thick material
that has a very low resonant frequency—below the limits of human hearing.
To minimize the resonance of the shoebox, you can put some soft, heavy fab-
ric inside it before you snap the lid on. A hand towel or some socks should be
sufficient to absorb some of the vibration.
Adding an Amplifier
Back in the 1950s, you needed vacuum tubes, transformers, and other power-
hungry heavyweight components to build an audio amplifier. Today, you can
buy a chip for about $1 that will do the job, if you add a few capacitors around
it, and a volume control. The TEA2025B that I’m recommending is intended for
use in cheap portable cassette players and CD players, and can work in stereo
or mono mode, from a power supply ranging from 3 to 9 volts. With 9 volts
and the two sides of the chip bridged together to drive one 8Ω speaker, it can
generate 5 watts of audio power. That doesn’t sound much compared with a
typical home theater system rated at 100 watts per channel, but because loud-
ness is a logarithmic scale, 5 watts will be quite enough to irritate any family
members in the same room—and possibly even in other rooms.
If you can’t find the TEA2025B chip, you can use any alternative listed as an
audio amplifier.Try to find one that is designed to drive an 8Ω speaker with up
to 5 watts in mono mode. Check the manufacturer’s data sheet to see where
you attach capacitors around it. Note carefully whether some of the capacitors
have no polarity marked, even though they have fairly high values, such as 100
μF. These capacitors must function regardless of which way the alternating
current is flowing, and I’ve marked them “NP” in my schematic in Figure 5-41,
meaning “nonpolarized.” (You may find them identified as “bipolar” or “BP” in
parts catalogs.) As noted in the shopping list, you can put two 220 μF capaci-
tors in series, negative-to-negative, to get the same effect as a single 100 μF
nonpolarized capacitor.
For this project, it’s essential to include the regular 100 μF electrolytic smooth-
ing capacitor across the power supply. Otherwise, the amplifier will pick up
and—yes, amplify—small voltage spikes in the circuit.
Figure 5-39. A resonant enclosure is neces-
sary if you want to hear some bass (lower
frequencies) from your speaker. A cheap
plastic shoebox is sufficient for demo
purposes.
Figure 5-40. Drill some half-inch holes
in the bottom of the box, then bolt the
speaker in place, running a wire out
through a hole in one end. Snap on the lid,
and you’re ready for not-quite-high-fidelity
audio.

What Next? 251
0.15uF 0.15uF
0.22uF
10K
33K
100uF
NP
8 ohms
10uF NP100ft hookup
wire on spool
100uF
100uF
NP
100uF
100uF
1
2
3
4 13
14
15
16
5
6
7
8 9
10
11
12
9V
DC
100uF
TEA2025B
Input from
headphone jack
on audio device
Figure 5-41. The audio amplifier chip should be wired with capacitors around it as shown,
“NP” denoting the ones that are not polarized. The acronym“BP,” meaning bipolar, is also
often used to mean the same thing. The output from pins 2 and 15 of the chip can be
passed through a coil or a 10 μF capacitor to demonstrate audio filtering.
The input shown in the schematic can receive a signal from a typical media
player, such as a portable MP3 player, CD player, or cassette player. To connect
its headphone jack to the breadboard, you can use an adapter that converts
it to a pair of RCA-type audio jacks, and then stick a wire into one of them as
shown in Figure 5-42. The wire will connect to the 33K resistor on the bread-
board circuit. The chromed neck of the RCA jack (which is sometimes gold-
plated, or at least gold-colored) must be connected with the negative side of
your power supply on the breadboard; otherwise, you won’t hear anything.
You can ignore the second output on the adapter, because we’re working in
mono, here, not stereo.
Figure 5-42. To sample the output from the
headphone socket of a music player, you
can use this adapter and push the stripped
end of a piece of hookup wire into one of
the sockets. Then use alligator clips on a
jumper wire to connect the audio to your
breadboarded circuit. Don’t forget to use
an additional jumper wire to connect the
outside of the socket to the negative side
of the power supply on the breadboard.
Because we’re only using one speaker, the
amplifier is connected to only one of the
stereo outputs from your player. The other
is ignored.

Chapter 5252
The 33K resistor is necessary to protect the amplifier from being overdriven. If
you don’t get enough volume using your music player, decrease the 33K value.
If the music is too loud and distorted, increase the value.You can also try omit-
ting or increasing the 10K resistor next to it, which is included in an effort to
reduce background hum noise.
I’ve shown two switches at the top of the schematic: one to bypass a coil, the
other to bypass a capacitor. You can use alligator clips instead, as long as you
can easily compare the sound when each of the components is inserted into
the circuit.
Figure 5-43 shows a coil consisting of a spool of hookup wire being used. The
red and black alligator clips resting loose on top of the shoebox will go to the
output from the chip (on pins 2 and 15). There is no polarity; it doesn’t matter
which clip goes to which pin.
Begin by turning the volume control on your music source all the way down
before you apply power. Don’t be surprised if you hear humming or crackling
noises when you activate the amplifier; it will pick up any stray voltages, be-
cause in this simple experiment, I haven’t suggested that you should shield
the input, and the amplifier circuit can pick up noise, as its wires can act like
antennas.
Note that you may also get additional unwanted sound if you use the ampli-
fier on a conductive desktop surface. Remove any aluminum foil or conductive
foam for this project.
Make sure that your player is playing music, and slowly turn up its volume
control until you hear it. If you don’t hear anything, you’ll have to check for
circuit errors.
Now comes the interesting part. Insert the 100-foot spool of hookup wire be-
tween one output from the amplifier, and one input of the speaker (it doesn’t
matter which one), or if you used switches, open the switch that bypasses the
coil.You should find that the music loses all its high-end response. By compari-
son, if you disconnect the coil and substitute a 10 μF capacitor, you should find
that the music sounds “tinny,” meaning that it loses all its low range, leaving
only the high frequencies.
You’ve just tested two very simple filters. Here’s what they are doing:
• The coil is a low-pass filter. It passes low frequencies but blocks high fre-
quencies, because brief audio cycles don’t have time to overcome the coil’s
self-inductance. A bigger coil eliminates a wider range of frequencies.
• The capacitor is a high-pass filter. It passes high frequencies and blocks
low frequencies because longer audio cycles can fill the capacitance, at
which point the capacitor stops passing current. A smaller capacitor elimi-
nates a wider ranger of frequencies.
You can go a lot farther into filter design, using complex combinations of coils
and capacitors to block frequencies at any point in the audible spectrum.
Search online for audio filter schematics—you’ll find hundreds of them.
Figure 5-43. The red and black alligator
clips, lying on top of the shoebox, should
connect with the output from your ampli-
fier chip. The red jumper wire passes the
signal through a coil of hookup wire on its
way to the speaker. Note the change in
sound when you short out the coil.

What Next? 253
Crossover Networks
In a traditional audio system, each speaker cabinet contains two drivers—one
of them a small speaker called a tweeter, which reproduces high frequencies,
the other a large speaker known as a woofer, which reproduces low frequen-
cies. (Modern systems often remove the woofer and place it in a separate box
of its own that can be positioned almost anywhere, because the human ear
has difficulty sensing the direction of low-frequency sounds.)
The schematic that you just looked at and may have constructed is known as
a“crossover network,”and truly hardcore audiophiles have been known make
their own (especially for use in car systems) to go with speakers of their choice
in cabinets that they design and build themselves.
If you want to make a crossover network, you should use high-quality poly-
ester capacitors (which have no polarity, last longer than electrolytics, and are
better made) and a coil that has the right number of turns of wire and is the
right size to cut high frequencies at the appropriate point. Figure 5-44 shows
a polyester capacitor.
Figure 5-45 shows an audio crossover coil that I bought on eBay for $6. I was
curious to find out what was inside it, so I bought two of them, and took one
apart.
First I peeled away the black vinyl tape that enclosed the coil. Inside was some
typical magnet wire—copper wire thinly coated with shellac or semitransparent
plastic, as shown in Figure 5-46. I unwound the wire and counted the number
of turns.Then I measured the length of the wire, and finally used a micrometer
to measure the diameter of the wire, after which I checked online to find a con-
version from the diameter in mils (1/1,000 of an inch) to American wire gauge.
As for the spool, it was plain plastic with an air core—no iron or ferrite rod in
the center. Figure 5-47 shows the spool and the wire.
Figure 5-44. Some nonelec-
trolytic capacitors have
no polarity, such as this
high-quality polyester film
capacitor. However, they tend
to be much more expensive,
and are hard to find in values
higher than 10 μF.
Figure 5-45. What exotic
components may we find
inside this high-end audio
component that’s used with
a subwoofer to block high
frequencies?
Figure 5-46. The black tape is
removed, revealing a coil of
magnet wire.
Figure 5-47. The audio crossover coil
consists of a plastic spool and some
wire. Nothing more.

Chapter 5254
So here’s the specification for this particular coil in an audio crossover network.
Forty feet of 20-gauge copper magnet wire, wrapped in 200 turns around a
spool of 1/16–inch-thick plastic with a hub measuring 7/8 inch in length be-
tween the flanges and 1/2-inch external diameter. Total retail cost of materials
if purchased separately: probably about $1, assuming you can find or make a
spool of the appropriate size.
Conclusion: there’s a lot of mystique attached to audio components. They are
frequently overpriced, and you can make your own coil if you start with these
parameters and adjust them to suit yourself.
Suppose you want to put some thumping bass speakers into your car. Could
you build your own filter so that they only reproduce the low frequencies?
Absolutely—you just need to wind a coil, adding more turns until it cuts as
much of the high frequencies as you choose. Just make sure the wire is heavy
enough so that it won’t overheat when you push 100 or more audio watts
through it.
Here’s another project to think about: a color organ. You can tap into the out-
put from your stereo and use filters to divide audio frequencies into three sec-
tions, each of which drives a separate set of colored LEDs. The red LEDs will
flash in response to bass tones, yellow LEDs in response to the mid-range, and
green LEDs in response to high frequencies (or whatever colors you prefer).
You can put signal diodes in series with the LEDs to rectify the alternating cur-
rent, and series resistors to limit the voltage across the LEDs to, say, 2.5 volts
(when the music volume is turned all the way up). You’ll use your meter to
check the current passing through each resistor, and multiply that number
by the voltage drop across the resistor, to find the wattage that it’s handling,
to make sure the resistor is capable of dissipating that much power without
burning out.
Audio is a field offering all kinds of possibilities if you enjoy designing and
building your own electronics.

What Next? 255
Theory
Waveforms
If you blow across the top of a bottle, the mellow sound
that you hear is caused by the air vibrating inside the bottle,
and if you could see the pressure waves, they would have a
distinctive profile.
If you could slow down time and draw a graph of the alter-
nating voltage in any power outlet in your house, it would
have the same profile.
If you could measure the speed of a pendulum swinging
slowly to and fro in a vacuum, and draw a graph of the speed
relative to time, once again it would have the same profile.
That profile is a sine wave, so called because you can derive
it from basic trigonometry. In a right-angled triangle, the
sine of an angle is found by dividing the length of the side
opposite the angle by the length of the hypoteneuse (the
sloping side of the triangle).
To make this simpler, imagine a ball on a string rotating
around a center point, as shown in Figure 5-48. Ignore the
force of gravity, the resistance of air, and other annoying
variables. Just measure the vertical height of the ball and di-
vide it by the length of the string, at regular instants of time,
as the ball moves around the circular path at a constant
speed. Plot the result as a graph, and there’s your sine wave,
shown in Figure 5-49. Note that when the ball circles below
its horizontal starting line, we consider its distance negative,
so the sine wave becomes negative, too.
Why should this particular curve turn up in so many places
and so many ways in nature? There are reasons for this
rooted in physics, but I’ll leave you to dig into that topic if it
interests you. Getting back to the subject of audio reproduc-
tion, what matters is this:
• Any sound can be broken down into a mixture of sine
waves of varying frequency and amplitude.
Or, conversely:
• If you put together the right mix of audio sine waves,
you can create any sound at all.
Suppose that there are two sounds playing simultaneously.
Figure 5-50 shows one sound as a red curve, and the other
as pale blue. When the two sounds travel either as pressure
waves through air or as alternating electric currents through
a wire, the amplitudes of the waves are added together to
make the more complex curve, which is shown in black.
Now try to imagine dozens or even hundreds of different
frequencies being added together, and you have an idea of
the complex waveform of a piece of music.
b
b
a
a
Start
Figure 5-48. If a weight on the end of a string (length b, in
the diagram) follows a circular path at a steady speed, the
distance of the weight from a horizontal center line (length a,
in the diagram) can be plotted as a graph relative to time. The
graph will be a sine wave, so called because in basic trigonom-
etry, the ratio of a/b is the sine of the angle between line b and
the horizontal baseline, measured at the center of rotation.
Sinewaves occur naturally in the world around us, especially in
audio reproduction and alternating current.
Time
Ratioofa/b
Figure 5-49. This is what a “pure” sinewave looks like.
Figure 5-50. When two sinewaves are generated at the same
time (for instance, by two musicians, each playing a flute),
the combined sound creates a compound curve. The blue
sinewave is twice the frequency of the red sinewave. The
compound curve (black line) is the sum of the distances of the
sinewaves from the baseline of the graph.

Chapter 5256
Theory
Waveforms (continued)
You can create your own waveform as an input for your au-
dio amplifier with the basic astable 555 timer circuit shown
in Figure 5-51. You have to be careful, though, not to over-
load the amplifier input. Note the 680K series resistor on the
output pin of the timer. Also note the 500Ω potentiometer.
1
2
3
4 5
6
7
8
555
timer
1K
100K
680K
0.1uF
0.01uF
9V
DC
To input of
audio amplifier
500
ohms
Figure 5-51. A 555 timer is wired in astable mode using the
component values shown here to generate a wide range of
audible frequencies when the 100K potentiometer is adjusted.
After the output is reduced in power, it can feed into the ampli-
fier chip that was used previously.
Disconnect your music player and connect the output from
the 555 circuit to the input point (the 33K resistor) in the
amplifier circuit shown earlier in Figure 5-41. You don’t have
to worry about a separate connection on the negative side
as long as the 555 timer shares the same breadboard and
the negative side of its power supply.
Make sure that the 500Ω potentiometer is turned all the
way to short the output from the timer to the negative side
of the power supply. This functions as your volume control.
Also make sure the 100K potentiometer is in the middle of
its range. Switch on the power and slowly turn up the 500Ω
potentiometer until you hear a tone.
Now adjust the 100K potentiometer to create a low-pitched
note. You’ll find that it doesn’t have a“pure”sound. There
are some buzzing overtones. This is because the 555 timer
is generating square waves such as those shown in Figure
5-52, not sine waves, and a square wave is actually a sum
of many different sine waves, some of which have a high
frequency. Your ear hears these harmonics, even though
they are not obvious when you look at a square-shaped
waveform.
Route one of the connections to your loudspeaker through
your spool of hookup wire, and now you should hear a
much purer tone, as the buzzing high frequencies are
blocked by the self-inductance of the coil. Remove the coil
and substitute the 10 μF capacitor, and now you hear more
buzzing and less bass.
You’ve just taken a small step toward sound synthesis. If this
subject interests you, you can go online and search for oscil-
lator circuits. For a thorough understanding of the relation-
ship between waveforms and the sounds you hear, you’ll
really need an oscilloscope, which will show you the shape
of each waveform that you generate and modify.
Time
Voltage
Figure 5-52. The output from a 555 timer is either “on” or “off,”
with a very fast transition between those two states. The result
is an almost perfect square wave. Theoretically, this can be
disassembled into a complex set of sine waves that have many
different frequencies. The human ear hears the high frequen-
cies as harsh overtones.

What Next? 257
Experiment 30: Fuzz
Experiment 30: Fuzz
Let’s try one more variation on the circuit in Experiment 28. This will demon-
strate another fundamental audio attribute: distortion.
You will need:
• One more 100K potentiometer.
• Generic NPN transistors: 2N2222 or similar. Quantity: 2.
• Various resistors and capacitors.
Background
Clipping
In the early days of“hi-fi”sound, engineers labored mightily
to perfect the process of sound reproduction. They wanted
the waveform at the output end of the amplifier to look
identical with the waveform at the input end, the only dif-
ference being that it should be bigger, so that it would be
powerful enough to drive loudspeakers. Even a very slight
distortion of the waveform was unacceptable.
Little did they realize that their beautifully designed tube
amplifiers would be abused by a new generation of rock
guitarists whose intention was to create as much distortion
as possible.
The most common form of waveform abuse is techni-
cally known as“clipping.”If you push a vacuum tube or a
transistor to amplify a sine wave beyond the component’s
capabilities, it“clips”the top and bottom of the curve. This
makes it look more like a square wave, and as I explained in
the section on waveforms, a square wave has a harsh, buzz-
ing quality. For rock guitarists trying to add an edge to their
music, the harshness is actually a desirable feature.
Figure 5-53. This Vox Wow-Fuzz pedal was one of the early
stomp boxes, which deliberately induced the kind of distortion
that audio engineers had been trying to get rid of for decades.
The first gadget to offer this on a commercial basis was
known as a“fuzz box,”which deliberately clipped the input
signal. An early fuzz box is shown in Figure 5-53. The clip-
ping of a sine wave is shown in Figure 5-54.
Figure 5-54. When a sinewave (top) is passed through an
amplifier which is turned up beyond the limit of its components
(shown as dashed lines, center), the amplifier chops the wave
(bottom) in a process known as “clipping.” The result is close
to a square wave and is the basic principle of a fuzz box com-
monly used to create a harsh guitar sound.

Experiment 30: Fuzz
Chapter 5258
Schematic
The output from the 555 timer is a square wave, so it already sounds quite
“fuzzy,” but we can make it more intense to demonstrate the clipping princi-
ple. I’ve redrawn the whole circuit in Figure 5-55, as several components have
changed. The principal alteration is the addition of two NPN transistors.
If you assemble this circuit on your breadboard, note carefully that the 33K
and 10K resistors at the bottom of the amplifier chip have been removed, and
there’s now just an 820Ω resistor in that location. The bottom of the adjacent
0.22 μF capacitor is still the input point for the amplifier, and if you follow the
connection around to the middle of the schematic, you’ll find it leading to a
100K potentiometer. This is your“fuzz adjuster.”
The two NPN transistors are arranged so that the one on the left receives out-
put from the 555 timer. This signal controls the flow of electricity through the
transistor from a 33K resistor. This flow, in turn, controls the base of the right-
hand transistor, and the flow of current through that is what ultimately con-
trols the amplifier.
When you power up the circuit, use the 100K potentiometer attached to the
555 timer to adjust the frequency (as before) and crank the“fuzz adjuster”po-
tentiometer to hear how it adds increasing“bite”to the sound until ultimately
it becomes pure noise.
The two transistors act as amplifiers. Of course, we didn’t need them for that
purpose—the input level for the amplifier chip was already more than ade-
quate. The purpose of the lefthand transistor is simply to overload the right-
hand transistor, to create the “fuzz” effect. And when you turn up the output
from the transistors with the“fuzz adjuster,”eventually they overload the input
of the amplifier chip, creating even more distortion.
If you want to tweak the output, try substituting different values for the 1K
resistor and the 1 μF capacitor that are positioned between the emitter of the
righthand transistor and the negative side of the power supply. A larger resis-
tor should overload the transistor less. Different capacitor values should make
the sound more or less harsh.
You can find literally thousands of schematics online for gadgets to modify
guitar sound. The circuit I’ve included here is one of the most primitive. If you
want something more versatile, you should search for“stomp box schematics”
and see what you can find.

What Next? 259
Experiment 30: Fuzz
0.15uF
1uF
1K
0.15uF
0.22uF
820
100uF
NP
8 ohms
100uF
100uF
NP
100uF
100uF
1
2
3
4 13
14
15
16
5
6
7
8 9
10
11
12
9V
DC
100uF
TEA2025B
1
2
3
4 5
6
7
8
555
timer
1K
100K
100K
33K
3908K2
0.01uF
0.1uF0.01uF
0.1uF
Audio Signal
input point
Figure 5-55. For a quick demo of clipping, insert a couple of transistors between the output
from the 555 timer and the input of the amplifier chip. One transistor overdrives the
other, so that when you adjust the potentiometer at the center of the circuit, you hear an
increasingly harsh, distorted sound.

Experiment 30: Fuzz
Chapter 5260
Background
Stomp-box origins
The Ventures recorded the first single to use a fuzz box,
titled“The 2,000 Pound Bee,”in 1962. Truly one of the most
awful instrumentals ever made, it used distortion merely
as a gimmick and must have discouraged other musicians
from taking the concept seriously.
Ray Davies of the Kinks was the first to embody distortion
as an integral part of his music. Davies did it initially by plug-
ging the output from one amp into the input of another,
supposedly during the recording of his hit“You Really Got
Me.”This overloaded the input and created clipping—the
basic fuzz concept. From there it was a short step to Keith
Richards using a Gibson Maestro Fuzz-Tone when the Roll-
ing Stones recorded“(I Can’t Get No) Satisfaction”in 1965.
Today, you can find thousands of advocates promoting
as many different mythologies about“ideal”distortion. In
Figure 5-56, I’ve included a schematic from Flavio Dellepi-
ane, a circuit designer in Italy who gives away his work (with
a little help from Google AdSense) at http://www.redcircuits.
com. Dellepiane is self-taught, having gained much of his
knowledge from electronics magazines such as the British
Wireless World. In his fuzz circuit, he uses a very high-gain
amplifier consisting of three field-effect transistors (FETs),
which closely imitate the rounded square-wave typical of an
overdriven tube amp.
Dellepiane offers dozens more schematics on his site, devel-
oped and tested with a dual-trace oscilloscope, low-distortion
sinewave oscillator (so that he can give audio devices a“clean”
input), distortion meter, and precision audio volt meter.
This last item, and the oscillator, were built from his own
designs, and he gives away their schematics, too. Thus his
site provides one-stop shopping for home-audio electronics
hobbyists in search of a self-administered education.
Before fuzz, there was tremolo. A lot of people confuse this
with vibrato, so let’s clarify that distinction right now:
• Vibrato applied to a note makes the frequency waver
up and down, as if a guitarist is bending the strings.
• Tremolo applied to a note makes its volume fluctuate,
as if someone is turning the volume control of a guitar
up and down very quickly.
9V
DC
Input
Jack
Output
Jack
0.1uF
2K2
100K
22uF
100pF
10K
log
3K3
5Ktrimmer
22uF
0.1uF
1M
2N3819
2N38192N3819
Figure 5-56. This circuit designed by Flavio Dellepiane uses three transistors to simulate the kind of distortion that used to be cre-
ated by overloading the input of a tube amplifier.

What Next? 261
Experiment 30: Fuzz
Background
Stomp-box origins (continued)
Harry DeArmond sold the first tremolo box, which he
named the Trem-Trol. It looked like an antique portable
radio, with two dials on the front and a carrying handle on
top. Perhaps in an effort to cut costs, DeArmond didn’t use
any electronic components. His steam-punkish Trem-Trol
contained a motor fitted with a tapered shaft, with a rubber
wheel pressing against it. The speed of the wheel varied
when you turned a knob to reposition the wheel up and
down the shaft. The wheel, in turn, cranked a little capsule
of“hydro-fluid,”in which two wires were immersed, carrying
the audio signal. As the capsule rocked to and fro, the fluid
sloshed from side to side, and the resistance between the
electrodes fluctuated. This modulated the audio output.
Today, Trem-Trols are an antique collectible. When industrial
designer Dan Formosa acquired one, he put pictures online
at http://www.danformosa.com/dearmond.html. And Johann
Burkard has posted an MP3 of his DeArmond Trem-Trol so
you can actually hear it: http://johannburkard.de/blog/music/
effects/DeArmond-Tremolo-Control-clip.html.
The idea of a mechanical source for electronic sound mods
didn’t end there. The original Hammond organs derived
their unique, rich sound from a set of toothed wheels
turned by a motor. Each wheel created a fluctuating induc-
tance in a sensor like the record head from a cassette player.
It’s easy to think of other possibilities for motor-driven
stomp boxes. Going back to tremolo: imagine a transpar-
ent disc masked with black paint, except for a circular stripe
that tapers at each end. While the disc rotates, if you shine
a bright LED through the transparent stripe toward a light-
dependent resistor, you would have the basis for a tremolo
device. You could even create never-before-heard tremolo
effects by swapping discs with different stripe patterns.
Figures 5-57 and 5-58 show the kind of thing I have in mind.
For a real fabrication challenge, how about an automatic
disc changer?
Today’s guitarists can choose from a smorgasbord of effects,
all of which can be home-built using plans available online.
For reference, try these special-interest books:
• Analog Man’s Guide to Vintage Effects by Tom Hughes
(For Musicians Only Publishing, 2004). This is a guide to
every vintage stomp box and pedal you can imagine.
• How to Modify Effect Pedals for Guitar and Bass by Brian
Wampler (Custom Books Publishing, 2007). This is an
extremely detailed guide for beginners with little or
no prior knowledge. Currently it is available only by
download, from sites such as http://www.openlibrary.
org, but you may be able to find the previous printed
edition from secondhand sellers, if you search for the
title and the author.
Of course, you can always take a shortcut by laying down a
couple hundred dollars for an off-the-shelf item such as a
Boss ME-20, which uses digital processing to emulate distor-
tion, metal, fuzz, chorus, phaser, flanger, tremolo, delay,
reverb, and several more, all in one convenient multi-pedal
package. Purists, of course, will claim that it“doesn’t sound
the same,”but maybe that’s not the point. Some of us simply
can’t get no satisfaction until we build our own stomp box
and then tweak it, in search of a sound that doesn’t come
off-the-shelf and is wholly our own.
Figure 5-57. Although electromechanical audio devices are
obsolete now, some unexplored possibilities still exist. This
design could create various tremolo effects, if anyone had the
patience to build it.
Figure 5-58. Different stripe patterns could be used in conjunc-
tion with the imaginary electromechanical device in Figure
5-57 to create various tremolo effects.

Experiment 31: One Radio, No Solder, No Power
Chapter 5262
No Power
Time now to go back one more time to inductance and capacitance, and dem-
onstrate an application which also makes use of the way that waveforms can
be added to each other. I want to show you how a simple circuit with no power
supply at all can receive AM radio signals and make them audible. This is of-
ten known as a crystal radio, because the circuit includes a germanium diode,
which has a crystal inside it. The idea dates back to the dawn of radio, but if
you’ve never tried it, you’ve missed an experience that is truly magical.
You will need:
• Rigid cylindrical object, such as a vitamin bottle. Quantity: 1.
• 22-gauge hookup wire, solid-core. Quantity: 60 feet.
• 16-gauge wire, stranded. Quantity: 100 feet.
• Polypropylene rope (“poly rope”) or nylon rope. Quantity: 10 feet.
• Germanium diode. Quantity: 1.
• High-impedance headphone. Quantity: 1.
The diode and headphone can be ordered from http://www.scitoyscatalog.com.
You cannot use a modern headphone of the type you wear with an MP3 player.
Some of these items are shown in Figure 5-59.
First, you need to make a coil. It should be about 3 inches in diameter, and you
can wind it around any empty glass or plastic container of that size, so long
as it’s rigid. A soda bottle or water bottle isn’t suitable, because the cumula-
tive squeezing force of the turns of wire can deform the bottle so that it isn’t
circular anymore.
I chose a vitamin bottle that just happened to be exactly the right size. To re-
move the label, I softened its adhesive with a heat gun (lightly, to avoid melt-
ing the bottle) and then just peeled it off. The adhesive left a residue, which
I removed with Xylol (also known as Xylene). This is a handy solvent to have
around, as it can remove“permanent”marker stains as well as sticky residues,
but you should always use latex or nitrile gloves to avoid getting it on your
skin, and minimize your exposure the fumes. Because Xylol will dissolve some
plastics, clearly it’s not good for your lungs.
After you prepare a clean, rigid bottle, drill two pairs of holes in it, as shown in
Figure 5-60. You’ll use them to anchor the ends of the coil.
Now you need about 60 feet of 22-gauge solid-core wire. If you use magnet
wire, its thin insulation will allow the turns of the coil to be more closely spaced,
and the coil may be slightly more efficient. But everyday vinyl-insulated wire
will do the job, and is much easier to work with.
Begin by stripping the first 6 inches of insulation from the end of the wire.
Now measure 50 inches along the insulated remainder and apply your wire
strippers at that point, just enough to cut the insulation without cutting the
Figure 5-59. Just add wire and a coil, and
this is all you need to receive AM radio
signals. The black disc becomes the
tuning dial, after it is screwed onto the
variable capacitor (right). This is actually
an optional extra. A germanium diode
(center) rectifies the radio signal. The
high-impedance earphone (top) creates a
barely audible sound.
Figure 5-60. A large, 3-inch diameter empty
vitamin bottle makes an ideal core for a
crystal radio coil. The drilled holes will
anchor wire wrapped around the bottle.

What Next? 263
wire. Use your two thumb nails to pull the insulation apart, revealing about a
half-inch of bare wire, as shown in Figure 5-61. Bend it at the center point and
twist it into a loop, as shown in Figure 5-62.
You just made a “tap,” meaning a point where you will be able to tap into the
coil after you wind it. You’ll need another 11 of these taps, all of them spaced
50 inches apart. (If the diameter of the bottle that you’ll be using as the core
of your coil is not 3 inches, multiply its diameter by 16 to get the approximate
desired spacing of taps.)
After you have made 12 taps, cut the wire and strip 6 inches off that end. Now
bend the end into a U shape about a half-inch in diameter, so that you can
hook it through the pair of holes that you drilled at one end of the bottle. Pull
the wire through, then loop it around again to make a secure anchor point.
Now wind the rest of the wire around the bottle, pulling it tightly so that
the coils stay close together. When you get to the end of the wire, thread it
through the remaining pair of holes to anchor it as shown in Figure 5-63. The
completed coil is shown in Figure 5-64.
Figure 5-62. Each exposed section of wire
is twisted into a loop using sharp-nosed
pliers.
Figure 5-63. The stripped end of the wire
is secured through the holes drilled in the
bottle.
Figure 5-64. The completed coil, wrapped
tightly around the bottle.
Your next step is to set up an antenna. If you live in a house with a yard outside,
this is easy: just open a window, toss out a reel of 16-gauge wire while holding
the free end, then go outside and string up your antenna by using polypro-
pylene rope (“poly rope”) or nylon rope, available from any hardware store,
to hang the wire from any available trees, gutters, or poles. The total length
of the wire should be about 100 feet. Where it comes in through the window,
suspend it on another length of poly rope. The idea is to keep your antenna
wire as far away from the ground or from any grounded objects as possible.
If you live in an apartment where you don’t have access to a yard outside, you
can try stringing your antenna around the room, hanging the wire from more
pieces of poly rope. The antenna should still be about 100 feet long, but obvi-
ously it won’t be in a straight line.
Hook the free end of your antenna to one end of your coil. At this point, you also
need to add a germanium diode, which functions like a silicon-based diode but
is better suited to the tiny voltages and currents that we’ll be dealing with. The
other end of the diode attaches to one of the wires leading to a high-impedance
Figure 5-61. Wire strippers expose the solid
conductor at intervals along a 22-gauge
wire.
HighVoltage!
The world around us is full of electric-
ity. Normally we’re unaware of it, but
a thunderstorm is a sudden reminder
that there’s a huge electrical poten-
tial between the ground below and
the clouds above.
If you put up an outdoor antenna,
never use it if there is any chance of a
lightning strike. This can be extreme-
ly dangerous. Disconnect the indoor
end of your antenna, drag it outside,
and push the end of the wire into the
ground to make it safe.

Chapter 5264
earphone. A normal modern earphone or headphone will not work in this circuit.
The return wire from the headphone is connected to a jumper wire, the other
end of which can be clipped to any of the taps in your coil.
One last modification, and you’ll be ready to tune in. You have to ground the
jumper wire. By this I mean connect it to something that literally goes into
the ground. A cold-water pipe is the most commonly mentioned option, but
(duh!) this will work only if the pipe is made of metal. Because a lot of plumb-
ing these days is plastic, check under the sink to see if you have copper pipes
before you try using a faucet for your ground.
Another option is to attach the wire to the screw in the cover plate of an elec-
trical outlet, as the electrical system in your house is ultimately grounded. But
the sure-fire way to get a good ground connection is to go outside and ham-
mer a 4-foot copper-clad grounding stake into reasonably moist earth. Any
wholesale electrical supply house should be able to sell you a stake. They’re
commonly used to ground welding equipment.
Figure 5-65. The simple pleasure of picking up a radio signal with ultra-simple components
and no additional power.

What Next? 265
Figures 5-66 and 5-67 show the completed radio.
If you’ve managed to follow these instructions (one way or another), it’s time
to tune your radio to the nearest station. Move the alligator clip at the end of
your patch cord from one tap to another on your coil. Depending on where
you live, you may pick up just one station, or several, some of them playing
simultaneously.
It may seem that you’re getting something for nothing here, as the earphone
is making noise without any source of power. Really, though, there is a source
of power: the transmitter located at the radio station. A large amplifier pumps
power into the broadcasting tower, modulating a fixed frequency. When the
combination of your coil and antenna resonates with that frequency, you’re
sucking in just enough voltage and current to energize a high-impedance
headphone.
The reason you had to make a good ground connection is that the radio sta-
tion broadcasts its signal at a voltage relative to ground. The earth completes
the circuit between you and the transmitter. For more information on this and
other concepts relating to radio, see the upcoming section“Theory: How radio
works.”
Enhancements
The higher your antenna is, the better it should work. In my location, this is a
major problem, as I live in a desert area without any trees. Still, just stringing
the wire out of my window and tethering it (with rope) to the front bumper of
my car enabled me to pick up a faint radio signal.
To improve the selectivity of your radio, you can add a variable capacitor, as
shown in the following section. This allows you to“tune”the resonance of your
circuit more precisely. Variable capacitors are uncommon today, but you can
find one at the same specialty source that I recommended for the earphone and
the germanium diode: the Scitoys Catalog (http://www.scitoyscatalog.com).
This source is affiliated with a smart man named Simon Quellan Field, whose
site suggests many fun projects that you can pursue at home. One of his clever
ideas is to remove the germanium diode from your radio circuit and substi-
tute a low-power LED in series with a 1.5-volt battery. This didn’t work for me,
because I live 40 miles from the nearest AM broadcaster. If you’re closer to a
transmitter, you may be able to see the LED varying in intensity as the broad-
cast power runs through it.
To Ground
To Antenna
To
Earphone
Figure 5-66. A signal from the antenna
can pass through the coil to ground. If the
jumper wire is attached to an appropriate
tap on the coil, it resonates with the radio
signal, just powerfully enough to energize
the earphone which is wired in series with
a diode.
Figure 5-67. The real-life version of Figure
5-66.

Chapter 5266
Theory
How radio works
When electrical frequencies are very high, the radiation
they create has enough energy to travel for miles. This is the
principle of radio transmission: A high-frequency voltage is
applied to a broadcasting antenna, relative to the ground.
When I say“ground”in this instance, I literally mean the
planet beneath us. If you set up a receiving antenna, it
can pick up a faint trace of the transmission relative to the
ground—as if the earth is one huge conductor. Actually
the earth is so large and contains so many electrons, it can
function as a common sink, like a gigantic version of the file
cabinet that I suggested you should touch to get rid of static
electricity in your body before touching a CMOS logic chip.
To make a radio transmitter, I could use a 555 timer chip run-
ning at, say, 850 kHz (850,000 cycles per second), and pass
this stream of pulses through an amplifier to a transmission
tower; if you had some way to block out all the other elec-
tromagnetic activity in the air, you could detect my signal
and reamplify it.
This was more or less what Marconi (shown in Figure 5-68)
was doing in 1901, after he had purchased rights to Edison’s
wireless telegraphy patent, although he had to use a primi-
tive spark gap, rather than a 555 timer, to create the oscil-
lations. His transmissions were of limited use, because they
had only two states: on or off. You could send Morse code
messages, and that was all.
Figure 5-68. Marconi, the great pioneer of radio (photograph
from Wikimedia Commons).
Five years later, the first true audio signal was transmitted
by imposing lower audio frequencies on the high-frequency
carrier wave. In other words, the audio signal was“added”to
the carrier frequency, so that the power of the carrier varied
with the peaks and valleys of the audio.
At the receiving end, a very simple combination of a capaci-
tor and a coil detected the carrier frequency out of all the
other noise in the electromagnetic spectrum. The values of
the capacitor and the coil were chosen so that their circuit
would“resonate”at the same frequency as the carrier wave.
Figures 5-69 and 5-70 illustrate these concepts.
Carrier frequency
Audio signal
Amplitude modulation
Figure 5-69. When an audio signal (middle) is combined elec-
tronically with a high carrer frequency (top), the result looks
something like the compound signal at the bottom. In actual-
ity, the carrier frequency would be much higher compared with
the audio frequency, by a radio of perhaps 1,000:1.
Amplitude
modulation
Chopped by
diode
Audible earphone
response
Figure 5-70. When the compound signal is passed through a
diode, only the upper half remains. An earphone cannot react
fast enough to reproduce the high carrier frequency, so it
“rides” the peaks and thus reproduces the audio frequency.
The schematic in Figure 5-71 shows the simple circuit that
you built by wrapping a coil around an empty vitamin
bottle. When a positive pulse was received by the antenna,
it resonated with the antenna and the coil, provided that
the antenna was long enough and the coil was tapped at
the appropriate number of turns.

What Next? 267
Theory
How radio works (continued)
Figure 5-71. An antenna at the top of the schematic picks up faint
electromagnetic radiation from a distant transmitter. The coil
at the left side is tapped at intervals so that its resonance can
be adjusted to match the carrier frequency of the radio signal.
Other frequencies are grounded (at the bottom of the sche-
matic). The diode passes the“top half” of the signal to the ear-
phone at the right, which is incapable of responding fast enough
to reproduce the carrier frequency, and thus filters it out, leaving
only the audio frequencies that were superimposed on it.
By adding a capacitor, you can tune the circuit. Now an
incoming pulse from the transmitter is initially blocked by
the self-inductance of the coil, while it charges the capacitor.
If an equally negative pulse is received after an interval that
is properly synchronized with the values of the coil and the
capacitor, it coincides with the capacitor discharging and the
coil conducting. In this way, the right frequency of carrier
wave makes the circuit resonate in sympathy. At the same
time, audio-frequency fluctuations in the strength of the
signal are translated into fluctuations in voltage in the circuit.
What happens to other frequencies pulled in by the an-
tenna? The lower ones pass through the coil to ground; the
higher ones pass through the capacitor to ground. They are
just“thrown away.”
The righthand half of the circuit samples the signal by pass-
ing it through a germanium diode and an earphone. The
power from the transmitter is just sufficient to vibrate the
diaphragm in the earphone, after the diode has subtracted
the negative half of the signal.
Look back at the diagram of the amplitude-modulated
signal. You’ll see that it fluctuates up and down so rapidly,
the earphone cannot possibly keep up with the positive-
negative variations—hence the need for the diode. It will
remain hesitating at the midpoint between the highs and
lows, producing no sound at all. The diode solves this prob-
lem by subtracting the lower half of the“audio envelope,”
leaving just the positive spikes of voltage. Although these
are still very small and rapid, they are now all pushing the
diaphragm of the earphone in the same direction, so that
it averages them out, approximately reconstructing the
original sound wave.
Figure 5-72 shows how the circuit can be enhanced with a
variable capacitor, to tune it without needing to tap the coil
at intervals.
Figure 5-72. By adding a capacitor to the circuit, its resonance
can be tuned more precisely. The diagonal arrow indicates that
a variable capacitor is used.
The radio can pull in the stations on the AM (amplitude-
modulated) waveband that happen to be most powerful in
your area. The waveband ranges from 300 kHz to 3 MHz. If
you find yourself interested in radio, your next step could
be to build a powered radio using a couple of transistors.
Alternatively you could build your own (legal) low-power
AM transmitter. There’s an ultra-simple kit available from
http://www.scitoys.com consisting of just two principal
components: a crystal oscillator, and a transformer, shown
in Figure 5-73. That’s all it takes.
Figure 5-73. An AM radio transmitter can be made from just
two components: a transformer (left) and a crystal oscillator
(right), available from http://www.scitoys.com.

Chapter 5268
Robotics is another application of electronics that deserves a book in itself—
or several books. So, once again, I’m going to give you an introduction fol-
lowed by some points that you can follow if you want to go further. As always,
I will start with the simplest possible device, which in the world of robotics is a
cart that finds its way around your living room.
You will need:
• SPST or SPDT microswitches requiring minimal pressure to activate them.
A force between 0.02 and 0.1 newtons would be ideal. Quantity: 2. See
Figure 5-74.
• DC gear-motor, rated for any voltage between 5 and 12, drawing a maxi-
mum of 100mA in its free-running state, output shaft turning between 30
and 60 RPM. Quantity: 1. A motor is shown in Figure 5-75.
• Disc or arm that fits securely onto your motor shaft. Quantity: 1.
• 555 timer. Quantity: 1.
• DPDT nonlatching relay rated for the same voltage as your motor.
Quantity: 1.
• 1/4-inch plywood or plastic, one piece about 2 feet square.
• #4 sheet-metal screws, 5/8 inch or 3/4 inch long. Quantity: 2 dozen.
• #6 bolts, 3/4 inch long, with nylon-insert lock nuts. Quantity: 2 dozen.
• 1/4-inch bolts, 1 inch long, with nuts, to mount the wheels. Quantity: 4.
I’m not specifying one particular motor, because if I did, it might not be avail-
able by the time you read this. Motors aren’t like logic chips, which have re-
tained their basic function throughout various improvements over a period
of several decades. Motors come and go, and many that you may run across
will be surplus parts that will never been seen again. Search online for “gear-
motor”or“gearhead motor”and find one as close as possible to the specifica-
tion that I have provided.The mechanical power output of the motor shouldn’t
be important, because we won’t be requiring it to do much work.
The important consideration when you buy your motor is that you should also
obtain something that fits onto its output shaft. Typically, this will be a disk or
arm that can be screwed into place. To this you can then add a larger wheel of
your own, which you can cut with a hole saw or make from the screw-on lid of
a jar, or anything else circular that you may find in the house.
A larger wheel will make your cart move faster than a smaller wheel, but will
reduce its torque, thus limiting its power to overcome obstacles.
This brings me to my next topic: fabrication. Although this is an electronics
book, motors are electromechanical devices, and you have to be able to install
them in some kind of a machine to get any interesting results. You can use
Figure 5-74. A microswitch has a small
button (at the front, righthand side in this
picture) that is often actuated by a pivoted
metal lever. The switch can respond to a
very light pressure, but can handle rela-
tively high currents.
Figure 5-75. For the Little Robot Cart, I
found this 5-volt motor, which is supplied
with a disc that fits its output shaft. The
combination cost less than $10.

What Next? 269
plywood to complete the two little robotics projects here (ideally, the kind of
thin, high-quality plywood sold by hobby stores) but I recommend something
that looks better and is easier to work with: ABS plastic. Before you start on the
robotic cart, you may want to check the section“Fundamentals: All about ABS.”
Fundamentals
All about ABS
Unless you think the steampunk movement isn’t going back far enough, you
probably don’t want your autonomous robot cart to resemble a relic from
before the 1800s. Therefore, wood may not be the best construction material.
Metal can look nice, but is not easy to work with. For quick results that have a
twentieth-century look (maybe even a 21st-century look), plastic is the obvious
choice, and I feel that ABS is the best type of plastic to use, because it provides
such quick, easy results. ABS stands for“acrylonitrile butadiene styrene.”Lego®
blocks are made of ABS. Car-stereo installers and model-railroad buffs use it.
You can use it, too. You can saw it, drill it, sand it, whittle it, and drive screws into
it, and it won’t warp, split, or splinter. It’s washable, doesn’t need to be painted,
and will last almost forever.
Delrin is another type of plastic, but tends to cost more and is a little tougher
to drill and cut. It’s a matter of personal preference. ABS machines fairly well,
but when you drill it, for example, it can“catch”on the bit and the piece will
spin with the bit due to the way that plastic chips off with the bit. Delrin is self-
lubricating and has better melting properties under the heat of machining, so it
drills and cuts much more cleanly and easily than ABS.
Where to find ABS
Pieces of ABS a couple of feet square are available from online sources such as
http://hobbylinc.com or estreetplastics (an eBay store), but you’ll save money if
you can truck on down to your nearest plastic supply house and buy it like ply-
wood, in sheets measuring 4 by 8 feet. To discover whether you have a nearby
plastic supply house, search for“plastic supply”in your yellow pages or Google
Local.
Piedmont Regal Plastics has many supply centers around the nation, but you’ll
have to collect it yourself, and they may not be willing to cut small pieces. You
can check online at http://www.piedmontplastics.com for their locations.
Stock colors of ABS include black, white, and“natural,”which is beige. Sheets
usually are textured on one side, which is the side that should face outward, as
it is more scratch-resistant than the smooth side.
Because you won’t be adding paint or other finishes, you’ll have to be careful
not to scuff the plastic or scratch it while working. Clean your bench thoroughly
before you begin, taking special care to remove any metal particles, which tend
to become embedded in the plastic. Use wooden shims in the jaws of your vise,
and avoid resting the plastic accidentally on any sharp tools or screws. Working
with ABS requires a clean environment and a very gentle touch.

Chapter 5270
Cut with Care
You can saw ABS, but if you use a table saw, the plastic will tend to melt and stick to
the blade. These smears will get warm and sticky when you feed the next piece of
plastic into the saw, and the result will be extremely unpleasant. The whirling blade
will grab the plastic and hurl it at you powerfully enough to break bones. This is
known as “kickback” and is a very serious risk when sawing plastic.
If you have extensive experience using a table saw, you are actually more vulnerable,
because the reflexes and cautions you have developed while dealing with wood will
not be adequate for working with plastic. Please take this warning seriously!
Your first and most obvious precaution is to use a plastic-cutting blade, which has
a larger number of thicker teeth to absorb the heat. The blade I have used is a Freud
80T, but there are others. If you use a blade that is not suitable, you will see it starting
to accumulate sticky smears. This is the only warning you will get. Clean that blade
with a solvent such as acetone, and never use it for ABS again.
Regardless of other precautions, always wear gloves and eye protection when using
a table saw, and stand to one side when feeding materials into it. Personally, after
one episode of kickback that I thought had broken my arm, I prefer not to use a table
saw on plastic at all.
For long, straight cuts, the alternatives include:
• Panel saw (big and expensive, but safe and accurate).
• Miniature handheld circular saw with a blade around 4 inches in diameter,
guided with a straight edge clamped to the sheet.
• Hand saw. This is my old-school preference. My favorite is a Japanese pull-to-cut
saw, which makes very clean cuts: the Vaughan Extra-Fine Cross-Cut Bear Saw,
9-1/2 inches, 17 tpi (teeth per inch). If you use one of these, be careful to keep your
free hand out of the way, as the saw can easily jump out of the cut. Because it is
designed to cut hard materials such as wood, it has no difficulty cutting soft flesh.
Gloves are strongly recommended.
Figure 5-76. The perils of kickback. Plastic easily sticks to the blade of a table saw,
which will hurl it at you unexpectedly. Use other tools to cut plastic.

What Next? 271
Curving Cuts
Curving cuts involve relatively little danger, although eye protection and
gloves are still advisable. My preferred tools:
• Band saw with a 3/8- or 1/4-inch blade designed for thin wood or plywood.
• Jigsaw. I have a special liking for the DeWalt XRP using Bosch blades that
are designed for hardwood or plastic. This will cut complex curves in ABS
as easily as scissors cutting paper.
No matter what type of saw you use, you’ll have to clean ragged bits of plas-
tic off the cut afterward, and the absolutely necessary item for this purpose
is a deburring tool, available from http://www.mcmaster.com and most other
online hardware sources. A belt sander or disc sander is ideal for rounding
corners, and a metal file can be used to remove bumps from edges that are
supposed to be straight.
Figures 5-77 through 5-80 show various cutting tools. Figure 5-81 shows a de-
burring tool, and Figure 5-82 shows a disc sander.
Figure 5-77. A band saw is an ideal tool for
cutting complex shapes out of ABS plastic.
You can often find them secondhand for
under $200.
Figure 5-78. A handheld circular saw, run-
ning along a straight-edge, is much safer
than a table saw for cutting plastic, and
can produce comparable results.
Figure 5-79. This Japanese-style saw cuts
when you pull it, rather than when you
push it. After some practice, you can use
it to make very accurate cuts. Because
ABS is so soft, minimal muscle-power is
required.
Figure 5-80. This DeWalt jigsaw can run at
very slow speeds, enabling precise and
careful work with plastic.
Figure 5-81. A deburring tool will clean and
bevel the sawn edge of a piece of plastic in
just a couple of quick strokes.
Figure 5-82. A belt sander or disc sander
is the ideal tool for rounding corners when
working with ABS plastic.

Chapter 5272
Making Plans
I like to use drawing software to create plans, and I try to print them at actual
scale. I tape them to the smooth side of a piece of white or natural-color ABS,
then use an awl to prick through the plan into the soft surface beneath. I re-
move the paper and connect the awl marks by drawing onto the plastic using
a pencil or a fine-point water-soluble pen. Its lines can be wiped away later
with a damp cloth. Don’t use a permanent marker, as the solvents that you will
need to clean it may dissolve the plastic.
Because ABS will tend to open a fissure when you bend it at any inside corner
where you don’t have a smooth radius, you need to drill holes at these loca-
tions, as shown in the cart plans in Figure 5-92 on page 275.
A regular half-inch drill bit is too aggressive; it will tend to jam itself into the
plastic within one turn of the drill. Use Forstner bits (shown in Figures 5-83 and
5-84) to cut nice smooth circles.
Note that the heat from bending will tend to make any marks on the plastic
permanent.
Bending It
A big advantage of plastic over wood is that you can make complex shapes by
bending them, instead of cutting separate pieces and joining them with nails,
screws, or glue. Unfortunately, bending does require an appropriate bender: an
electric heating element mounted in a long, thin metal enclosure that you place
on your workbench. The bender I use is made by FTM, a company that offers all
kinds of neat gadgets for working with plastic. Their cheapest bender, shown in
Figure 5-85, is just over $200 with a 2-foot element. You can get a 4-foot model
for about $50 more. Check them out at http://thefabricatorssource.com.
Avoid BurnsWhile Bending
A plastic bender will inflict serious burns if you happen to rest your hand on it ac-
cidentally, and because it has no warning light, you can easily forget that you have
left it plugged in. Use gloves!
To bend plastic, lay it over the hot element of a plastic bender for a brief time
(25 to 30 seconds for 1/8-inch ABS, 40 to 45 seconds for 3/16-inch, and up to a
minute for 1/4-inch). If you overheat the plastic, you’ll smell it, and when you
turn it over you’ll find it looks like brown melted cheese. Naturally you should
learn to intervene before the plastic reaches that point.
ABS is ready to bend when it yields to gentle pressure. Take it off the bender
and bend it away from the side that you heated. If you bend it toward the hot
side, the softened plastic will bunch up inside the bend, which doesn’t look
nice.
Figure 5-83. A Forstner drill bit makes
clean, precise holes; a large regular drill bit
will chew up ABS plastic and make a mess.
Figure 5-84. By drilling holes at any
location where two bends intersect, you
reduce the risk of the plastic fissuring.
Figure 5-85. Making clean, precise bends
in ABS is simply a matter of resting the
plastic over a bender that consists of an
electric heating element.

What Next? 273
You can work with it for about half a minute, and when you have it the way
you want it, spray or sponge water onto it to make it set quickly. Alternatively,
if you need more time, you can reheat it. The amount of force necessary to
bend the sheet increases in proportion with the length of the bend, so a long
bend can be difficult, and I usually insert it into a loose vise, push it a bit, move
it along to the next spot, and push it again.
Because plastic bending is very similar to making shapes in origami, it’s a good
idea to model your projects in paper before you commit yourself to ABS.
If you decide that you don’t want to spend money on a bender, don’t aban-
don plastic just yet—you can use screws to assemble separate sections with
greater ease and convenience than if you were working with wood.
Making 90-Degree Joints
Driving screws into the edge of a piece of plywood will almost always separate
its layers, but ABS has no layers (or grain, either), and never splits or shatters.
This means that you can easily join two pieces at 90° using small screws (#4
size, 5/8-inch long).
Figures 5-86 through 5-90 show the procedure for joining 1/8-inch (or thicker)
ABS to 1/4-inch ABS, which I regard as the minimum thickness when you’re
inserting screws into its edge:
1. Mark a guideline on the thinner piece of plastic, 1/8 inch from its edge.
For #4 screws, drill holes using a 7/64-inch bit. If you’re using flat-headed
screws, countersink the holes very gently.
Figure 5-86
2. Hold or clamp the pieces in place and poke a pen or pencil through the
holes to mark the edge of the 1/4-inch plastic beneath.
3. Remove the thin plastic, clamp the 1/4-inch plastic in a vise, and drill
guide holes for the screws at each mark, centered within the thickness of
the plastic. Because ABS does not compress like wood, the holes must be
larger than you may expect; otherwise, the plastic will swell around the
screw. A 3/32-inch bit is just right for a #4 screw.
4. Assemble the parts. Be careful not to overtighten the screws; it’s easy to
strip the threads that they cut in the soft plastic. Figure 5-87

Chapter 5274
Figure 5-88 Figure 5-89. Figures 5-86 through 5-89
illustrate four steps to join two pieces of
ABS using #4 sheet-metal screws. Cut
7/64-inch holes on a line 1/8 inch from the
edge of the first piece, then mark through
the holes to the edge of the second piece.
Drill 3/32-inch holes that are precisely
centered in the edge, then screw the
pieces together.
Figure 5-90. Three #4 screws driven into
the edge of ABS, using a 1/16-inch guide
hole, a 5/64-inch guide hole, and a 3/32-
inch guide hole. respectively Because the
first two guides holes were too small, the
plastic swelled around the screw (but did
not break).
Framing Your Cart
For reasons that will soon be apparent, I’ve chosen an unusual diamond-
shaped configuration of wheels. In the rendering shown in Figure 5-91, the
front wheel (at the far end of the cart) applies power, the rear wheel (at the
near end of the cart) steers the cart when backing up, and the side wheels
prevent it from falling over.
Depending on the type of motor that you buy, you’ll have to improvise a way
to mount it in the front section of the cart. Don’t be afraid to use kludges such
as cable ties, duct tape, or even rubber bands to attach the motor to the frame.
We’re making a rough prototype, here, not a thing of beauty (although if you
decide you like the cart, you can always rebuild it beautifully later).
The plan in Figure 5-92 shows the pieces that you will need. Part A is the body
of the cart. If you’re going to bend it from ABS, you should drill half-inch holes,
with a forstner bit, at the four inside corners, so that these corners have round-
ed edges. If you simply saw the plastic to make sharp 90° corners, the plastic
may develop fissures at the corners when you bend it. If you don’t have a plas-
tic bender and don’t feel inclined to buy one, you can make Part A from three
separate rectangles and then screw them together.
Figure 5-91. If you have 3D rendering
software, it can be a great way to test the
feasibility of a construction project before
you start cutting materials and trying to
fit pieces together. This rendering was a
proof-of-concept for the Little Robot Cart.

What Next? 275
2
3
3
3
3
8
9
5
2
1/2
2 1/2
2 1/2
1/2
1/4
2
3
4
2
Drill half-inch
holes to make
rounded inside
corners
Bend
Bend
Make
four
wheels
A
B
C
D
E F
Figure 5-92. These sections of 1/4-inch plastic can be assembled to create the simple cart
described in Experiment 31.
Part B is a wheel, of which you will need four. I cut them using a 3-inch hole
saw. The front wheel is screwed to whatever disc or arm you obtained to mate
with the shaft of your motor. See Figure 5-93.
Parts C, D, and E assemble to form a yoke in which the rear wheel is mounted. I
used a 2-inch hinge to pivot the yoke. The hinge is mounted on Part F, which is
a partition located midway in the frame of the cart. The photographs in Figures
Figure 5-93. A 3-inch wheel is screwed to
the disc that mates with the drive shaft of
the motor.

Chapter 5276
5-94 and 5-95 will help to make this clear. Initially, when you install Part F, use
only two screws, one each side, so that you can adjust its angle a little.This will
be necessary to optimize the contact of the wheels with the floor.
The side wheels and rear wheel must spin freely, but on the other hand, they
shouldn’t wobble. I simply tightened the nuts on the bolts that serve as axles
for the wheels, until there was maybe half a millimeter of clearance. I added a
drop of Loctite to stop the nuts from getting loose.
The plans don’t show precisely where to drill holes for the axle bolts, because
the location will depend on the size of your wheels. You can figure this out as
you go along. Just make sure that the side wheels aren’t mounted too low. We
don’t want them to lift the front wheel or the rear wheel off the floor. If the
side wheels are a fraction higher off the ground than the front and rear wheels,
that’s good.
If you have tile or wood floors, your cart may acquire better traction if you
wrap a thick rubber band around each disc that you use for the drive wheel
and the steering wheel.
The most important aspect of the construction is to place microswitches
where they’ll be triggered when the cart runs into something. I placed mine
at the front corners, as shown in Figures 5-96 and 5-97. And that brings me to
the electronics.
Figure 5-96 Figure 5-97. Two microswitches with metal
arms are mounted on each side of the
cart, where they will sense any obstacle.
The Circuit
The schematic is very, very simple, with only four principal components: two
microswitches that sense obstacles in front of the cart, one relay, and one 555
timer. You will also need a small power switch, a battery or battery pack, and
a resistor, and capacitors to go with the timer. A trimmer potentiometer will
allow you to adjust the “on” time of the 555 timer, which will determine how
long the cart takes to back up. See Figure 5-98.
Figure 5-94. The assembled body of the
cart, before adding control electronics.
The wheel at the righthand end will pull the
cart from left to right. The hinged trailing
wheel will allow the cart to move in a rela-
tively straight line when it moves forward,
but will tend to turn it when it backs up.
Figure 5-95. A closeup of the hinged trailing
wheel, which rotates freely and can flip
from side to side with minimal friction.

What Next? 277
0.01uF
47uF
100K
50K
10K
Motor
1
2
3
4 5
6
7
8
Figure 5-98. This ultrasimple schematic is all the cart needs to enable it to back up when it
hits an obstacle.
The motor I chose requires 5 volts, so I had to use a voltage regulator with a
9-volt battery. If your motor uses 6 volts, you can wire four AA batteries to it
directly. If you have a 12-volt motor, you can use two 9-volt batteries in series,
supplying power through a 12-volt voltage regulator.
Assemble the components, mount them on the cart, and switch it on, and it
should move forward slowly in a more-or-less straight line. If it moves back-
ward, reverse your connection to the terminals on the motor.
When the cart bumps into something, either of the microswitches will con-
nect negative voltage to the input pin of the 555 timer. This triggers the timer,
which runs in monostable mode, generating a single pulse lasting about 5
seconds, which closes the relay, which is wired so that it reverses the voltage
to the motor.
When the voltage is reversed to a simple DC motor, it runs backward. So the
cart backs up. Because the rear wheel is mounted in a yoke that pivots, the
yoke will tend to flip one way or the other, causing the cart to describe an
arc as it moves backward. At the end of the timer cycle, the relay relaxes and
the cart starts moving forward again. In forward mode, the rear wheel just
follows along without applying any steering force, so the cart tends to follow
a straight line—until it hits another obstacle, at which point it backs up, and
tries another path.

Chapter 5278
Fundamentals
All about limit switches
The most obvious enhancement for your cart would be a better steering
mechanism. You could use another motor to take care of this, with a pair of limit
switches. Because limit switches are a basic, important idea in conjunction with
motors, I’ll explain them in detail.
Figure 5-99 shows three successive views of a motor with an arm attached to it,
which can press either a lower pushbutton or an upper pushbutton. Both of the
pushbuttons are normally closed, but will open when pressed by the motor arm.
These buttons are the limit switches. Typically you would use microswitches for
this purpose, just like the ones that I suggested as barrier-sensors at the front of
the cart.
In addition, there’s a DPDT relay that is activated by a simple on/off switch at
the righthand side. On the cart, the 555 timer takes the place of the on/off
switch, by feeding power to the relay.
Suppose that the motor begins with the arm pointing downward, as shown
in the top view in Figure 5-99, and the motor is wired so that when it receives
negative voltage at its lower terminal and positive at its upper terminal, it
rotates counter-clockwise. This is what happens when the on/off switch closes
and sends power to the DPDT relay. Positive voltage from the relay contacts
cannot pass through the upper diode, but can pass through the upper limit
switch, which is closed. Negative voltage cannot pass through the lower limit
switch, because it’s open, but can pass through the lower diode. So, the motor
starts to turn counterclockwise. During the midpoint of its arc, it receives power
through both of the limit switches.
Finally, the motor arm reaches the upper switch, and opens it. This prevents
positive voltage from reaching the motor through that switch, and the positive
voltage is also blocked by the upper diode. So, at this time, the motor stops.
Now suppose that the on/off switch is opened, as in the top view in Figure
5-100. The relay loses its power, so its contacts relax. The voltage to the motor is
now reversed. Negative voltage passes through the upper diode, while positive
voltage reaches the motor through the lower limit switch. The motor starts
running clockwise, until its arm hits the lower switch, opening it and cutting off
power to the motor.
Limit switches are necessary, because if you continue to apply voltage to a
simple DC motor that is unable to turn, the motor sucks more current, gets hot,
and may burn out.
You can easily see how this kind of system could be used to control the cart’s
steering. Even though the motor has only two positions, these are sufficient to
make the cart turn when going backward, and proceed straight ahead when
going forward.
To reduce power consumption, the DPDT relay could be replaced with a two-
coil latching relay. The circuit would then have to be revised so that the relay is
flipped to and fro by a pulse to each of its coils.

What Next? 279
Fundamentals
All about limit switches (continued)
Figure 5-99. The three diagrams, from top to bottom, show
three snapshots of a motor controlled by a DPDT relay and
two limit switches. When the on/off switch at bottom-right
sends power to the relay, the lower relay contacts cause the
motor to run counterclockwise until it stops itself as its arm
opens the upper limit switch.
Figure 5-100. When the on/off switch at bottom-right opens,
the relay connects its upper contacts. This causes the motor
to run clockwise until its arm opens the lower limit switch.
Limit switches avoid the overheating and possible damage
that are likely when power is delivered to a motor that is
prevented from turning.

Chapter 5280
Fundamentals
All about motors
Brushed DC motor
This is the oldest, simplest design for an electric motor,
shown in very simplified form in Figure 5-101. Coils are
attached to a shaft where they can interact with sta-
tionary magnets around them. The magnetic attraction
turns the shaft a little, at which point the next coil on
the shaft is energized to turn the shaft a little more, and
then the next coil—and so on. To make this happen,
electricity has to be fed into the coils by“brushes,”often
consisting of soft carbon pads that conduct power to
a hub, known as a commutator, divided into sections,
each of which is connected to a separate coil.
This basic design has several advantages if we want to
build a small motorized gadget, such as a miniature
robot or even a model airplane:
• Widely available
• Low cost
• Simple
• Reliable
• Will run in reverse when voltage reverses
In addition, brushed motors are often sold with reduc-
tion gearing built in. Such units are known as gearhead
motors or gear motors. They free you from the need to
use your own gears or belts to adjust the output speed
yourself. You simply choose the motor that fits your
specification.
DC stepper motor
This requires a controller, consisting of some electron-
ics to tell the motor to rotate its shaft in small, discrete
steps. The advantages of a stepper motor are:
• Precise positioning of the shaft
• Precise speed adjustment
Stepper motors are ideal for devices such as computer
printers, where the paper has to roll up by a precise
distance and the print head has to move laterally by
an equally precise distance, but they are also useful in
robots. If the motor is small enough to draw less than
200mA and will run on 12 volts or less, you can control
it with pulses from a 555 timer. I’ll describe stepper mo-
tors in more detail in Experiment 33.
Servo motor
This is generally used in conjunction with a program-
mable microcontroller, which sends instructors to
rotate the motor shaft to a specific position and then
hold it there. I’ll mention servo motors when I intro-
duce you to microcontrollers, but we won’t be dealing
with them in detail.
Other types of motors exist, including brushless DC motors
(which require a different type of controller and are found
in computer disk drives and CD players), and AC motors
(including synchronous motors, which synchronize their
rotation with the frequency of AC voltage, and were used
extensively in clocks, before clocks mostly became digital).
In this book, I’ll be talking mostly about brushed DC motors
and DC stepper motors.
DC
Power
Magnet
Commutator
Brushes
Coil
Figure 5-101. The basic principle of a simple DC motor. The
commutator passes electricity through a coil, creating a mag-
netic field that interacts with a magnet around the motor. The
coil turns, and the commutator turns with it, until the electric
field through the coil is reversed. This causes the process to re-
peat. In reality, a motor is likely to have a commutator formed
from multiple segments, connected with multiple coils. The
principle, however, remains the same.

What Next? 281
Take-home messages from this experiment include the following:
• You can buy simple DC motors with reduction gearing built in, providing
your choice of RPM. Literally hundreds of websites will sell you small mo-
tors for robotics projects.
• When you reverse the voltage to a DC motor, the motor runs in reverse.
• A DPDT relay can be wired so that when it closes its contacts, it reverses a
power supply to a motor.
• You can use two limit switches and a pair of diodes to stop a motor at two
positions. In each of its stopping positions, the motor consumes no power
and you won’t have the risk of it burning out.
What other projects can you imagine using this simple set of techniques?
Mechanical Power
In the United States, the turning force, or torque, of a motor is usually mea-
sured in pound-feet or ounce-inches. In Europe, the metric system is used to
measure torque in dynes.
A pound-foot is easy to understand. Imagine a lever pivoted at one end, as
shown in Figure 5-102. If the lever is one foot long, and you hang a one-pound
weight at the end of it, the turning force is one pound-foot.
One foot
Rotational
force
(torque)
of one
pound-foot
1 lb. weight
Figure 5-102. The rotational force created by a motor is known as “torque,” and in the
United States it is measured in pound-feet (or ounce-inches, for small motors). In the
metric system, torque is measured in dynes. Note that the torque created by a motor will
vary according to the speed at which the motor is running.

Chapter 5282
Fundamentals
Wire gauges
If you’re going to power larger motors, or
other components that take more current than
LEDs or small relays, you really need to know
about wire gauges. In particular, what’s the
relationship between wire thickness and AWG
(American Wire Gauge)? And what gauge of
wire should you use for any given current?
You can find numerous charts and tables if you
go online, but many of these sources con-
tradict each other, especially on the topic of
how much current is safe to run through each
gauge of wire.
After making several comparisons (and testing
some wire samples myself), I’ve compiled the
table in Figure 5-103, which I recommend as a
compromise. Note the following:
• This table applies to solid-core copper
wire.
• For stranded wire, or copper that has
been tinned (giving it a silver appear-
ance), the number of ohms per foot will
increase, the number of feet per ohm will
decrease, and the maximum amperage
will decrease, probably by around 20%.
The maximum amperage assumes that the
wire is insulated, preventing it from radiating
heat as effectively as a bare conductor. I am
also assuming that the wire is likely to be at
least partially enclosed, inside a box or cabi-
net. At the amperages listed for each gauge of
wire, you should expect the wire to become
noticeably warm, and personally I would tend
to use thicker wire instead of the maximums
indicated in the table.
Most tables of this type only tell you the resis-
tance of each gauge of wire in ohms per 1,000
feet. I have included that number but have
also expressed the function the other way
around, as the number of feet per ohm, as this
doesn’t require you to do so much arithmetic
with decimals. 30 0.010 10
28 0.013 15
26 0.016 25
24 0.02 39
22 0.025 62
20 0.032 99
18 0.04 157
16 0.051 249
14 0.064 396
12 0.081 630
10 0.102 1,000
8 0.128 1,590
7 0.144 2,010
6 0.162 2,510
5 0.182 3,190
4 0.204 4,020
3 0.229 5,080
2 0.258 6,400
1 0.289 8,070
0 0.325 10,200
00 0.365 12,800
000 0.41 16,200
0000 0.46 20,400
AWG
Diameter
in
inches
Feet
per
ohm
103.2
64.9
40.1
25.7
16.1
10.2
6.39
4.02
2.53
1.59
0.999
0.628
0.498
0.395
0.313
0.249
0.197
0.156
0.124
0.098
0.078
0.062
0.049
Ohms
per
1,000 ft
0.5
1.0
1.5
2.5
5
8
10
13
17
23
32
44
51
60
70
80
90
100
125
150
175
200
225
Maximum
amps
(insulated)
Figure 5-103. American wire gauges (AWG) and their properties.

What Next? 283
Theory
Calculating voltage drop
Another fact that you often need to know is how much of
a voltage drop a particular length of wire will introduce in
a circuit. If you want to get maximum power from a motor,
you don’t want to lose too much voltage in the wires that go
to and from the motor.
Voltage drop is tricky, because it depends not only on the
wire, but also on how heavily the circuit is loaded. Suppose
that you are using 100 feet of 22-gauge wire, which has a
resistance of about 1.5 ohms. If you attach it to a 12-volt
battery and drive an LED and a series resistor offering a total
effective resistance of about 1,200 ohms, the resistance of
the wire is trivial by comparison. According to Ohm’s Law:
amps = volts / ohms
so the current through the circuit is only about 10mA.
Again, by Ohm’s Law:
so the wire with resistance of 1.5 ohms imposes a voltage
drop of 1.5 × 0.01 = 0.015 volts.
Now suppose you’re running a motor. The coils in the mo-
tor create impedance, rather than resistance, but still if we
measure how much current is going through the circuit, we
can establish its effective resistance. Suppose the current is
1 amp. Repeating the second calculation:
So the voltage drop in the wire is now 1.5 × 1 = 1.5 volts!
This is illustrated in Figure 5-104.
Bearing these factors in mind, I have compiled a table for
you. I’ve rounded the numbers to just two digits, as varia-
tions in the wire that you use make any pretense of greater
accuracy unrealistic.
To use this table, you need to know how much current is
passing through your circuit. You can calculate it (by adding
up all the resistances and dividing it into the voltage that
you are applying) or you can simply measure the current
with a meter. Just make sure that your units are consistent
(all in ohms, amps, and volts, or milliohms, milliamps, and
millivolts).
In the table, I have arbitrarily assumed a length of 10 feet
of wire. Naturally you will have to make allowances for the
actual length of wire in your circuit. The shorter the wire,
the less the loss will be. A circuit with only 5 feet of wire,
and the same amperage and voltage, will suffer half of the
percentage loss shown in the table. A circuit with 15 feet
of wire, and the same amperage and voltage, will suffer 1.5
times the percentage loss. So, to use the table:
1. Divide your length of wire by 10. (Make sure that you
measure the length in feet.)
2. Use the result to multiply the number in the table.
The table also arbitrarily assumes that you have a 12-volt
supply. Again, you will have to make allowances if you are
using a different voltage. So, to use the table:
1. Divide 12 by the actual voltage of your power supply.
2. Use the result to multiply the number in the table.
I can summarize those two steps like this:
Percent voltage lost = P × (12 / V) × (L / 10)
where P is the number from the table, V is your power-
supply voltage, and L is the length of your wire.
12 volt
battery
12 volt
battery
Motor
100feet
22gaugewire
1.5ohms
100feet
22gaugewire
1.5ohms
Effective
resistance
1200 ohms
Approx. 10 mA current
15mV voltage drop
Approx. 1A current
1.5 volts voltage drop
Effective
resistance
10.5 ohms
Figure 5-104. The voltage drop imposed by wiring will depend
on the current and the resistance in the circuit. The drop will
be greatest when the resistance of the circuit is low and the
amperage is high.

Chapter 5284
Theory
Calculating voltage drop (continued)
This table shows the percent voltage lost in a circuit with 10-foot wire at 12 volts.
Wire
Gauge
Amperes
1 2 3 4 5 6 7 8 9 10
10 0.08 0.17 0.25 0.33 0.42 0.50 0.58 0.67 0.75 0.83
12 0.13 0.27 0.40 0.53 0.66 0.80 0.93 1.1 1.2 1.3
14 0.21 0.42 0.63 0.84 1.1 1.3 1.4 1.5 1.9 2.1
16 0.33 0.67 1.0 1.3 1.7 2.0 2.3 2.7 3.0 3.4
18 0.53 1.1 1.6 2.1 2.7 3.2 3.7 4.3 4.8 5.3
20 0.85 1.7 2.6 3.4 4.3 5.1 6.0 6.8 7.7 8.5
22 1.3 2.7 4.0 5.4 6.7 8.1 9.4 11 12 13
24 2.1 4.3 6.4 8.6 11 13 15 17 19 21
26 3.4 6.8 10 14 17 20 24 27 31 34
28 5.4 11 16 22 27 32 38 43 49 54
30 8.6 17 26 34 43 52 60 69 77 86
Remember, though, that the wire resistance will be higher if you are using stranded copper wire or tinned copper wire, and
this will increase the percentage of voltage lost.
Time now to build something more sophisticated: a cart that orients itself to-
ward a light source. I’m going to tell you all you need to get started on this
project, but this time I won’t go all the way to the end in exhaustive detail. I
want you to get into the habit of figuring out the details, improving on plans,
and eventually inventing things for yourself.
You will need:
• Trimmer potentiometer, 2K linear. Quantity: 2.
• LEDs. Quantity: 4. If you get tired of using series resistors to protect LEDs in
a 12-volt circuit, consider buying 12-volt LEDs such as Chicago Miniature
606-4302H1-12V, which contain their own resistors built in. However, the
schematic in Figure 5-108 assumes that you will use regular 2V or 2.5V LEDs.
• Stepper motor: Unipolar, four-phase, 12-volt. Parallax 27964 or similar,
consuming 100mA maximum. Quantity: 2.
• Photoresistors, ideally 500 to 3,000Ω range. Quantity: 2.

What Next? 285
• ULN2001A or ULN2003A Darlington arrays by STMicroelectronics.
Quantity: 2.
• CMOS octal or decade counter. Quantity: 2.
• Various resistors and capacitors.
Exploring Your Motor
I’ve specified a unipolar, four-phase, 12-volt motor because this is a very com-
mon type. A typical sample is shown in Figure 5-105. If you can’t easily find
the one that I’ve listed, you should feel safe in buying any other that has the
same generic description.“Unipolar”means that you don’t have to switch the
power supply from positive to negative and back to positive again, to run the
motor. Four-phase means that the pulses that run the motor must be applied
in sequence to four separate wires. Because you will be running your motor
directly from 555 timers, the lower its power consumption, the better.
First, though, we can apply voltage to the motor without using any other com-
ponents at all. Most likely it will have five wires already attached, with the ends
stripped and tinned, so that you can easily insert them into holes in a bread-
board, as shown in Figure 5-106. Check the data sheet for your motor; you
should find that four of the wires are used to energize the motor and turn it in
steps, while the fifth is the common connection. In many cases, the common
connection should be hooked to the positive side of your power supply, while
you apply negative voltage to the other four wires in sequence, one step at a
time.
The data sheet will tell you in what sequence to apply power to the wires. You
can figure this out by trial and error if necessary. One thing to bear in mind: a
stepper motor is very tolerant. As long as you apply the correct voltage to it,
you can’t burn it out.
To see exactly what the motor is doing, stick a piece of duct tape to the end of
the shaft. Then apply voltage to wires, one at a time, by moving your negative
power connection from one to the next. You should see the shaft turning in
little steps.
Inside the motor are coils and magnets, but they function differently from
those in a DC motor. You can begin by imagining the configuration as being
like the diagram in Figure 5-107. Each time you apply voltage to a different
coil, the black quadrant of the shaft turns to face that coil. In reality, of course,
the motor turns less than 90° from one coil to the next, but this simplified
model is a good way to get a rough idea of what’s happening. For a more pre-
cise explanation, see the upcoming section“Theory: Inside a stepper motor.”
Bear in mind that as long as any of the wires of the motor are connected, it
is constantly drawing power, even while sitting and doing nothing. Unlike a
regular DC motor, a stepper motor is designed to do nothing for much of the
time. When you apply voltage to a different wire, it steps to that position and
then resumes doing nothing.
Figure 5-105. A typical stepper motor. The
shaft rotates in steps when negative pulses
are applied to four of the wires in sequence,
the fifth wire being common-positive.
12V DC
Figure 5-106. The simplest test of a step-
per motor is to apply voltage manually
to each of its four control wires, while a
piece of duct tape, attached to the output
shaft, makes it easy to see how the motor
responds.

Chapter 5286
The coil inside the motor is holding the shaft in position, and the power that
the motor draws will be dissipated as heat. It’s quite normal for the motor to get
warm while you’re using it.The trouble is, if you use a battery to power it, and you
forget that you have it connected, the battery will not hold its charge for long.
Quick Demo
Now that you’ve proved that your motor is functional, how can you actually
run it? You need to send a pulse to each of the four wires in turn, in a rapidly
repeating sequence. If you can also adjust the speed of the pulses, so much
the better. I’m thinking that for a quick and simple demo, you can handle the
challenge simply by using four 555 timers, all of them in monostable mode,
with each one triggering the next.
The schematic in Figure 5-108 shows what I have in mind. It looks more com-
plex than it really is. Each timer has the same pattern of components around it,
so after you create the first module, you just make three copies of it.
555
10K
10K
8K2
22uF
1K
1K
1K
1K
22uF
22uF
22uF
0.01uF
0.01uF
0.01uF
0.01uF
10K
10K
10K
10K
10K
555
555
555
Stepper
Motor Figure 5-108. A very quick and simple
circuit to control a stepper motor uses
four 555 timers, each in monostable
mode, triggering each other in a
repeating sequence.
1
2
3
4
Figure 5-107. This greatly simplified
diagram helps in visualizing the way in
which a stepper motor works. In reality,
almost all motors rotate by less than 90° in
response to each pulse.

What Next? 287
I’ve used a 10K resistor to pull up the input to each 555, so that the timers are
naturally in their quiescent state. A 0.01 μF capacitor links the output from one
timer to the input of the next so that they are electrically isolated from each
other, and the capacitor just conveys a “spike” of voltage when one timer fin-
ishes its“on”cycle, and its output goes low, which triggers the next.
On the righthand side, I’ve used 10K resistors and 22 μF capacitors to generate
a cycle of about a quarter of a second—except that the topmost timer has a
8K2 timing resistor. The reason for this is that when power is first applied, the
timers will all be waiting for each other to begin, and timers 2 and 4 or 1 and
3 may fire together. By giving one timer a shorter cycle than the others, I mini-
mize this problem.
The LEDs are included just to give you some visual verification of what’s hap-
pening. Without them, if you make a wiring error, the motor may turn to and
fro erratically, and you won’t know why. Initially you can run your circuit with
only the LEDs connected, just to make sure it works. Figure 5-109 shows the
breadboarded circuit before the motor is plugged in. Then add the motor by
plugging its wires into the breadboard, where you’ll make connection with the
outputs (pins 3) of the timers. See Figure 5-110.
Apply power, and you should see the motor turning in steps, in sequence with
the LEDs. If the LED sequence isn’t stable:
1. Connect a wire directly from the input (pin 2) of the topmost timer to the
positive side of the voltage supply, and wait for the timers to calm down.
2. Restart the sequence by disconnecting the free end of this wire, or (if nec-
essary) touch the free end of it briefly to the negative side of the supply,
to trigger the first timer.
One thing you may have noticed, if you’re paying very close attention: the
common terminal of the motor is connected to positive.Therefore, when each
timer flashes positive, that positive signal isn’t actually powering the motor.
The low outputs from the three timers that are not firing at any given moment
are sinking current from the motor. It seems quite happy with this arrange-
ment. You’ll need some theory to understand why.
Figure 5-109. To test the control circuit for
errors, four LEDs show the outputs from
the four 555 timers. The loose yellow wire
at the righthand side connects to pin 2
of the first timer. Touch the free end of
this wire to the positive side of the power
supply to reset the timers, and then, if nec-
essary, make a brief negative connection
with the free end of the wire to restart their
sequence.
Figure 5-110. After the circuit has been
tested, the motor can be added by hook-
ing its control wires to the outputs of the
four 555 timers.

Chapter 5288
Theory
Inside a stepper motor
If you check the Wikipedia entry for stepper motors, you
may see a very nice 3D rendering showing a toothed rotor
and four coils arrayed around it. Maybe stepper motors
used to be manufactured like this once upon a time, but not
anymore.
Imagine two horizontal rows of coils. In the space between
them is a series of little magnets, like a freight train, that
can move left or right, as shown in Figures 5-111 and
5-112. Each coil has two windings, in opposite directions,
so that current through one winding will create an upward
magnetic force while current through the other will create
a downward force. Each row of windings is connected in
parallel, so that they switch on and off simultaneously.
In Step 1, the negative connection energizes the upper
windings of the upper coils, which creates an upward mag-
netic force. I’ve shown this force using blue-green arrows so
that you won’t mistake it for a flow of electricity. It so hap-
pens that this force attracts the north poles of the magnets
and repels the south poles, so if the magnets begin in the
position shown in Step 1, they will want to move one step
to the right.
This brings them to the position shown in Step 2. Now the
upper windings of the lower coils are energized, and again,
this produces an upward force, which again attracts the
north poles and repels the south poles.
This advances the magnets to their location in Step 3.
Now the lower windings of the upper coils are energized,
producing a downward force. This repels the north poles of
the magnets and attracts their south poles. So the magnets
keep moving.
They reach the position shown in Step 4. The lower wind-
ings of the lower coils are energized, producing a downward
force which continues to attract the south poles while
repelling the north poles. So the magnets move a final step
to the right—which leaves them in the same orientation
shown in Step 1. And the process can repeat all over again.
NS NS NS NS
NS NS NS NS
Step 1
Step 2
Figure 5-111. This sequence shows the first two steps as the rotor
of a stepper motor (shown as a series of north-south magnets)
moves in response to pulses through electromagnets.
NS NS NS NS
NS NS NS NS
Step 3
Step 4
Figure 5-112. After taking another two steps, the motor will be
back where it started at Step 1 in Figure 5-111.

What Next? 289
Theory
Inside a stepper motor (continued)
In reality, the magnets are not separate from each other.
The edge of a rotor is magnetized in zones that alternate
between south and north polarity. And instead of multiple
coils, there are just four windings that go around all the
magnetic cores. But the principle is exactly the same. The 3D
rendering gives a general idea, and the photograph shows
what I found when I cracked open a typical stepper motor.
Now bear in mind that when this device is driven by a set of
555 timers, we don’t just connect negative to one wire at a
time on the left, leaving the others floating. In reality, at any
given moment, three of the timers have a negative output
and the fourth has a positive output. The last diagram in
Figure 5-112 shows this situation.
Suppose the top wire is positive while the other three are
negative, as shown in Figure 5-113. The positive output
does nothing, because it is balanced by the positive power
on the other end of the coils. The two negatives attached to
the bottom set of coils create equal and opposite forces that
cancel each other out (while wasting some power). So the
net result is the same as in Step 3.
In fact, you should find that you can disconnect the com-
mon wire completely while using the stepper motor with
555 timers, and the motor will still turn, because one of
the timers is providing positive power while the others are
negative. In fact, you’ll be running them more efficiently this
way.
NS NS NS NS
Figure 5-113. When the motor is driven by four 555 timers, they
are activating it by sinking positive voltage from it. The interior
workings of the motor look something like this. It’s not the
most efficient way to do the job.
Figures 5-114 and 5-115 may help to give you a clearer idea
of what the motor actually looks like inside.
Figure 5-114. This 3D rendering gives a better idea of what a
typical stepper motor looks like inside. The copper coils and
gray cylinders are stationary, while the black disc rotates
between them.
Figure 5-115. When a stepper motor is broken open, this is
what you’re likely to find. On the left, the rotor of the motor,
which has a magnetized band around its circumference, is still
attached to the lower half of the casing. On the right, the upper
half of the casing has been opened, and the coil has been re-
moved (actually the winding you can see consists of two coils,
wound in opposite directions). The spikes are the magnetic
cores that exert force on the rotor.

Chapter 5290
Speed Control
If you are a truly exceptionally observant, you may have noticed that I left pin 5 of
each of the timers unconnected in the schematic for driving the stepper motor in
Figure 5-108. Normally, pin 5 should be grounded through a capacitor to prevent
it from picking up stray voltages which can affect the accuracy of the chip.
I left the pins unconnected because I had a plan for them. In fact, changing the
timing of the chip is exactly what we want to do now, as a way to change the
speed of the stepper motor.
If you tie pin 5 of all four timers together, as shown in Figure 5-116, and put
a 2K trimmer potentiometer (shown in Figure 5-117) between them and the
negative side of the power supply, you’ll find that as you turn the trimmer
to reduce its resistance, the timers start to run faster. Figure 5-118 shows the
breadboard layout. Eventually, when the resistance goes below around 150
ohms, everything stops. The LEDs go dark, because you’ve reduced the volt-
age on pin 5 below the threshold level that the 555 timer finds acceptable.
555
10K
10K
8K2
22uF
1K
1K
1K
1K
22uF
22uF
22uF
0.01uF
0.01uF
0.01uF
0.01uF
10K
10K
10K
10K
10K
555
555
555
Stepper
Motor
2K
Figure 5-116. To adjust the speed of the sequence of 555 timers, their control pins (pin
5 on each timer) are linked together and attached to a trimmer potentiometer that
adjusts the resistance between the pins and the negative side of the power supply.
Figure 5-117. Close-up of a trimmer potentiometer
with pins spaced at 1/10 inch for insertion in a
breadboard or perforated board. The brass screw,
at top-left, turns a worm gear inside the unit, al-
lowing precise adjustment of internal resistance.
Figure 5-118. The trimmer potentiometer has been
added to the circuit, allowing motor speed control.

What Next? 291
Initially I suggested a step time of 1/4 second just so that you could see what
was happening. When you’re actually using this circuit, you’ll never need it to
run as slowly as that. So you can increase the entire range of speeds. Remove
the 22 μF timing capacitors and substitute, say, 4.7 μF capacitors, or smaller.
Now when you adjust the potentiometer, you’ll get a useful range of speed.
Adding Autonomy
Currently, the circuit simply does what you tell it to do. The next step is to
make it autonomous—in other words, give it the illusion of making up its own
mind. I’m thinking that instead of a trimmer potentiometer, we could substi-
tute a photocell, properly known as a photoresistor. Typically, the resistance of
a cadmium sulfide photo resistor is highest in the dark, and lowest when light
shines on it.
One problem with photoresistors is that they’re not as widely available as
many other types of electronic components. If you search Mouser.com, for
instance, you’ll find virtually nothing. Partly this is because the online search
function at Mouser is the weakest feature of the site, and partly it’s because
Mouser is not oriented toward hobbyists. What you need to do is conduct a
“product search.”Go to http://www.google.com/products, enter the search terms
“CdS” and “photocell,”and you’ll find a bunch of cheap cadmium sulfide com-
ponents from places you may never have heard of.
Because photoresistors seem to come and go as erratically as DC motors, I am
not offering any part numbers. You can buy any product that has an appropri-
ate minimum resistance (in bright light) and maximum resistance (in the dark).
If you find a component that ranges from 500 to 3,000Ω, that would be a good
choice. If the only ones you can find have a higher minimum than 500Ω, you
could consider putting a couple of them in parallel.
Setting Up Your Light Seeking Robot
Why would you want to control the speed of a stepper motor by using a photo
resistor? Because the original objective was to build a robot that is attracted
to light.
The idea is simple enough: use two stepper motors, each controlling the
speed of one wheel of the cart. Use two photoresistors, each controlling the
speed of the opposite stepper motor. When the righthand photoresistor picks
up more light, its resistance lowers, causing the lefthand set of timers to run
faster, which will make the lefthand wheel run faster. Thus, the cart will turn
toward the light. Figure 5-119 illustrates the concept.
Before you start wiring more 555 timers, though, you might consider doing
the job with a more appropriate component. The ULN2001A and ULN2003A
are chips containing Darlington amplifiers specifically designed to deliver cur-
rent to inductive loads such as solenoids, relays, and (you guessed it) motors.
Each chip has seven inputs that require very little current, and seven outputs
that can deliver 500mA each. The inputs are TTL and CMOS compatible (the
2001A has a wider tolerance for voltages than the 2003A) and each channel of
Photo-
Resistors
Stepper
Motors
555 Timers555 Timers
Figure 5-119. If two photoresistors control
the speed of two 555-timer arrays, the
difference in speed between one wheel
and the other can turn the cart toward a
light source.

Chapter 5292
the chip functions as an inverter, so that when the input goes high, the output
goes low and sinks current. This is of course just what we need for our stepper
motor that has a common positive connection.
The ULN2001A is only an amplification device, so you have to precede it with
a counter that runs from 1 to 4 and then repeats. You can stick with your 555
timers, as you’ve already assembled them, or substitute almost any CMOS oc-
tal or decade counter that sends its output pulses to a series of pins. Just use
the output from the fifth pin as the “carry” output to restart the counting se-
quence. I suggest a CMOS counter simply because it will run on 12 volts, so
you can use the same power supply that suits your stepper motors.
If you switch to CMOS counters, you will still need a pair of 555 timers send-
ing pulses to the counters. The timers will be free-running in astable mode,
and your photoresistors will control their speed. Figure 5-120 shows the
configuration.
One last item: you’ll need a 12-volt battery.You can of course put eight AA cells
together, but I think you should consider a rechargeable pack from a source
such as http://www.all-battery.com, which has a section entirely devoted to“ro-
bot batteries.”
If you put it all together, you should find that when you place your robot cart in
a very dimly lit room, it will turn toward the beam from a bright, well-focused
flashlight. To get reliable results, you may have to recess each of the photo-
resistors in little tubes, so that they receive much more light when they face
your flashlight than when they face away from it. Figure 5-121 is a 3D render-
ing of the concept.
Another idea is to rewire your cart so that it actually runs away from the light.
Can you imagine how this might be done?
Just one more thought: if you use infrared photoresistors, you can control your
cart with beams from infrared LEDs, in normal room lighting. If you and a cou-
ple of friends all have infrared transmitters, you can get your cart to run from
one of you to the next, like an obedient dog.
This takes us about as far as I’m going to go into robotics. I urge you to check
out the sites online if you want to pursue the topic further. You can also buy a
wide variety of robot kits, although of course I feel that it’s more fun to invent
or develop things for yourself.
All that’s left now is to perform one last introduction: to a device that should
make your life much easier, even though the device is much more complicated
than anything we have dealt with so far.
Photo-
Resistors
Stepper
Motors
555 Timer
Counter
Amplifier
555 Timer
Counter
Amplifier
Figure 5-120. A more efficient way to drive
the motors is to use just one timer to set
the speed of each, with a counter and
amplifier (such as a Darlington array chip)
sending the pulses down the wires. The
principle is still the same, though.
Figure 5-121. This 3D rendering shows a
possible configuration of the light-seeking
cart, with two photoresistors enclosed in
small tubes to restrict their response to
light.

What Next? 293
Throughout this book, in accordance with the goal of learning by discovery, I
have asked you to do an experiment first, after which I’ve suggested the gen-
eral principles and ideas that we can learn from it. I now have to change that
policy, because the next experiment involves so much setup that it’s only fair
to tell you what to expect before you begin the preparations.
We are about to enter the realm of controller chips, often known as MCUs,
which is an acronym for micro controller unit. An MCU contains some flash
memory, which stores a program that you write yourself. The flash memory is
like the memory in a portable media player, or the memory card that you use
in a digital camera. It needs no electricity to power it. In addition, the chip has
a processor which carries out the instructions in your program. It has RAM to
store the values of variables on a temporary basis, and ROM, which tells it how
to perform tasks such as sensing a varying voltage input and converting it into
digital form for internal use. It also contains an accurate oscillator, so that it
can keep track of time. Put it all together, and it’s a tiny computer that you can
buy for under $5.
Let’s suppose that you have a greenhouse where the temperature must never
fall below freezing. You set up a temperature sensor, and you have two dif-
ferent heaters. You want to switch on the first heater if the temperature falls
below 38° Fahrenheit. But if, for some reason, that heater is broken, you want
to switch on the second, backup heater when the temperature goes below 36°
Fahrenheit.
Programming a MCU to take care of this can be very simple indeed. You could
even add extra features, such as a second temperature sensor, just in case the
first one fails, and you could tell the chip to use whichever sensor gives a lower
reading.
Another application for a MCU would be in a fairly elaborate security system.
The chip could monitor the status of various intrusion sensors, and can take
various preprogrammed steps, depending on the sensors’ status. You could
include delay intervals, too.
Many MCUs have additional useful features built in, such as the ability to con-
trol servo motors that turn to a specific angle in response to a stream of pulses.
Servos are widely used in radio-controlled model boats, airplanes, and hobby
robotics.
Perhaps you are now wondering why, if MCUs can do all this, haven’t we been
using them all along? Why did I spend so much time describing the develop-
ment of an alarm system using discrete components, if one chip could have
done everything?

Chapter 5294
There are three answers:
1. MCUs cannot do everything. They need other components to help them
interact with the world, such as transistors, relays, sensors, and amplifiers.
You need to know how those things work, so that you can make intel-
ligent use of them.
2. MCUs can introduce their own kinds of problems and errors, associated
with using software in addition to hardware. I’ll have more to say about
this later.
3. MCUs have limits and restrictions, most obviously their requirement for a
5-volt regulated power supply, and their inability to source or sink much
current from each pin. They also demand that you learn a programming
language (which differs from one brand of MCU to the next). And to get
the program into the chip, you have to be able to plug it into a computer
and do a download, which is not always convenient.
In this experiment, you’ll learn how to write a program for a small and simple
MCU, and you’ll transfer the program into it and see how it works.
Background
Origins of programmable chips
In factories and laboratories, many procedures are repetitive. A flow sensor may
have to control a heating element. A motion sensor may have to adjust the
speed of a motor. Microcontrollers are perfect for this kind of routine task.
A company named General Instrument introduced an early line of MCUs in 1976,
and called them PICs, meaning Programmable Intelligent Computer—or Pro-
grammable Interface Controller, depending which source you believe. General
Instrument sold the brand to another company named Microchip Technology,
which owns it today.
“PIC”is trademarked, but is sometimes used as if it’s a generic term, like Scotch
tape. In this book, I’ve chosen a range of controllers based on the PIC architec-
ture. They are licensed by a British company named Revolution Education Ltd.,
which calls its range of chips the PICAXE, for no apparent logical reason other
than that it sounds cool.
I like these microcontrollers because they were developed originally as an edu-
cational tool and because they are very easy to use. They’re cheap, and some of
them are quite powerful. Despite their odd name, I think they’re the best way to
get acquainted with the core concepts of MCUs.
After you play with the PICAXE, if you want to go farther into MCUs, I suggest
the BASIC Stamp (which uses a very similar language, but with additional pow-
erful commands) and the very popular Arduino (which is a more recent design,
packed with powerful features, but requires you to learn a variant of C language
to program it). I’ll say more about these chips later.
If you search for“picaxe”on Wikipedia, you’ll find an excellent introduction to
all the various features. In fact, I think it’s a clearer overview than you’ll get from
the PICAXE website.

What Next? 295
Supplies
Figure 5-122 shows some of the chips in the PICAXE range. I’ll be telling you
how to use the smallest—the 08M—which costs less than $5 and is cheaper
than any other MCU that I’ve found. It has only 256 bytes of memory to store a
program (not gigabytes, megabytes, or kilobytes, just 256 bytes!), but you’ll be
surprised how many possibilities this amount allows for. Figure 5-123 shows
a closeup of the 08M with its legs safely embedded in a piece of conductive
foam.
In the United States, there are three distributors of this chip:
• http://www.advancedmicrocircuits.com
• http://www.phanderson.com/picaxe
• http://www.sparkfun.com
I like P. H. Anderson for its grass-roots hobbyist approach, and they have good
prices if you want to buy multiple chips. But SparkFun Electronics offers other
associated products that you may find interesting.
All the distributors will want to sell you“starter kits,”such as the one in Figure
5-124, perhaps because the PICAXE itself is so cheap that it doesn’t offer much
of a profit margin. Still, for our purposes, you should buy the chip as a stand-
alone item. And buy two of them, just in case you damage one (for example,
by connecting voltage to it incorrectly).
Figure 5-123. When supplied by one of its
American distributors, a PICAXE 08M
arrives embedded in a little square of
conductive foam. The chip is the same size
as a 555 timer but has the power of a tiny
computer.
Figure 5-124. A typical PICAXE kit includes
a printed circuit board, which you may not
really need, and some other not-entirely-
essential items. But the 3.5-mm stereo
jack socket (top, center) is absolutely
necessary.
To download your programming instructions into the chip, first you’ll type the
instructions on a computer, and then you’ll feed them through a cable into
the PICAXE memory. So you’ll need to buy a cable, and you’ll need software to
help you to write the program.
Figure 5-122. A page from the PICAXE cata-
log lists only some of the chips that are
available. What began as an educational
aid has become a useful prototyping tool.

Chapter 5296
You can use the PICAXE with a serial cable, but I don’t recommend it.The old RS-
232 serial communications standard on PCs is pretty much obsolete, and PICAXE
has recognized this by offering a USB cable (which contains a serial converter
inside its plug). The USB cable is a little more expensive, but is also simpler and
compatible with Apple computers. From any of the U.S. distributors, buy USB
cable part AXE027, also sold as part PGM-08312 by http://www.sparkfun.com
(quantity: 1). The cable is shown in Figure 5-125.
To write your software and send it down the wire to the chip, the PICAXE
Programming Editor is the tool of choice. It comes in only a Windows ver-
sion. For those who prefer Mac OS or Linux, you can get a free download of
another piece of software known as AXEpad, which has fewer features, but
will do the job. All the downloadable software is freely available from http://
www.rev-ed.co.uk/picaxe/software.htm.
Finally, you need a 3.5-mm stereo audio socket with solder connections. The
reason for this is that the manufacturers of the PICAXE have used a stereo au-
dio plug on the free end of their USB cable, and you have to be able to plug
it into something. The PICAXE breadboard adapter, SparkFun stock number
DEV-08331, contains the necessary stereo socket in addition to a few other
little items. Quantity: 1. See Figure 5-126.
Oddly enough, the USB cable is the most expensive item on the list, because
of the electronics hidden inside it.
Software Installation and Setup
Now you have to go through a setup procedure. There is no way around this.
Here is what you will be doing:
1. Install a driver so that your computer will recognize the special USB cable.
2. Install the Programming Editor software (or AXEpad for Mac/Linux) so
that your computer will help you to write programs and then download
them into the chip.
3. Mount the PICAXE on your breadboard and add the socket to receive
downloads.
These steps are explained in the following sections.
The USB driver
Fair warning: If you go to the PICAXE website and try to use its search function,
it probably won’t find what you want. Search for“USB Driver,”for instance, and
it will pretend it has never heard of such a thing.
The PICAXE home page also has irritating drop-down menus that tend to dis-
appear just when you’re about to click on them, but at the time of writing, you
can bypass these issues by going straight to the Software Downloads section
at http://www.rev-ed.co.uk/picaxe/software.htm.
Figure 5-125. The USB download cable
made for use with the PICAXE terminates
in a 3.5-mm audio plug. This should not be
inserted in any audio device. It establishes
a serial connection with a computer, allow-
ing program code to be downloaded into
the chip.
Figure 5-126. Closeup of the 3.5-mm stereo
socket that is used with the USB download
cable.

What Next? 297
Scroll down past all the software until you get to Additional Resources. Look
for the AXE027 PICAXE USB Download Cable. At first glance, it looks as if they
want to sell you a cable, but in fact this is the list of drivers. Double-click the
one appropriate to your computer, and choose a destination on your com-
puter for the download—a place where you will find it easily, such as your
desktop.
The download will leave you with a zipped file folder. You will have to unzip it.
OnWindows XP, right-click the folder and choose“Extract all.” View the extract-
ed files and you will find a PDF installation guide. Linux and Mac users can find
instructions currently stashed at http://www.rev-ed.co.uk/docs/AXE027.pdf.
When installing the driver on a Windows platform, here are a few tips to mini-
mize your exasperation level:
1. Remember, the special USB cable contains some electronics. It is not just
a cable, but a device designed for interacting with a PICAXE chip. Don’t try
to use it for anything else!
2. You have to plug the cable into a USB port before you install the driver, be-
cause your computer will need to verify that the driver matches the cable.
3. You must not attach the PICAXE to the other end of the cable until after
you have installed the driver.
4. Every USB port on your computer has a separate identity. Whichever one
you choose when you first plug in the cable, you should use that port
every time in the future. Otherwise, you will have to repeat the process of
telling your computer what the cable is.
5. Bearing in mind Tip #4, you should avoid using the cable in a standalone
USB hub.
6. The cable is fooling the PICAXE into thinking that it’s talking to a serial
port on your computer.Those“communication”ports are known as COM1,
COM2, COM3, or COM4. When you install the driver, the installer will
choose one of those COM ports for you, and later you will have to know
which one it is. The PDF guide should help you through this procedure.
Unfortunately, you cannot skip it.
The Programming Editor software
If you have come this far, you’re ready for the next big step, which is much
easier.You need the PICAXE Programming Editor, available for free on the Soft-
ware Downloads web page where you found the USB driver. (If you are using a
Mac or Linux, you will need AXEpad, which is on the same web page.)
Downloading and installing the Programming Editor should be simple and
painless. Once you have done that, you should find that it has placed a shortcut
on your desktop. Double-click it, go to View→Options, and in the window that
opens (shown in Figure 5-127), click the Serial Port tab. You should see a dialog
box like the one in Figure 5-128. Now make sure that the Programming Editor is
looking at the same COM port that was chosen by the USB driver. Otherwise, the
Programming Editor won’t know where to find your PICAXE chip.
Be careful not to download the driver
for the USB010 USB-Serial adapter
by mistake. The USB-Serial adapter is
something else entirely.

Chapter 5298
In the Programming Editor, go to View→Options and click the Mode tab, then
click the button to select the 08M chip.
Figure 5-127. This screenshot shows the options win-
dow of the PICAXE Program Editor, which you must use
to select the type of chip that you intend to program (in
our case, the 08M).
Figure 5-128. Another screenshot of the options window
shows the second essential choice that you must
make: selection of the COM port that the installer
chose on your computer.
Are we having fun yet? Obviously not, but you’re through with software has-
sles for the time being.The last step before you’re ready to use the PICAXE is to
mount it, and its socket, on your breadboard.
Setting up the hardware
The PICAXE 08M looks like a 555 timer. (Other chips in the PICAXE range have
more pins and more features.) It requires a properly regulated 5 volts, just like
the logic chips you dealt with previously. In fact, the PICAXE people are rather
emphatic about protecting it from voltage spikes. They want you to use two
capacitors (one 100 μF, one 0.1 μF) on either side of an LM7805 regulator. This
seems like overkill, but the PICAXE is more inconvenient to replace than a 555
timer. You certainly can’t run down to RadioShack to buy one. So let’s do what
the manufacturer says, just in case, and set up a breadboard as shown in Fig-
ures 5-129 and 5-130.
Now for the chip itself. Note that the pins for positive and negative power are
exactly opposite to those for the 555 timer, so be careful!
Set up your breadboard following the schematic shown in Figure 5-131. Note
that I am showing the stereo socket on its underside, because I think that’s
how you’ll have to use it with the breadboard. If you try to stick its pins into the
holes in the board, they will fit, but when you insert the plug into the socket,
the thickness of the plug will tend to raise the socket up so that it loses con-
tact. I really think the way to go is to solder wires to the pins on the socket and
push the wires into the breadboard. See Figure 5-133.
9V DC input
(unregulated)
5V DC output
(regulated)
0.1uF
0.1uF
100uF
100uF
Figure 5-129. PICAXE documentation
specifies a 100 μF and 0.1 μF capacitor
on the input side of a 5-volt regulator, and
a similar pair of capacitors on its output
side. On a breadboard, they can be ar-
rayed like this.
Figure 5-130. The actual components for
power regulation, applied to a breadboard,
delivering 5 volts (positive and negative)
down each side.

What Next? 299
330
10K
1
2
3
4 5
6
7
8
PICAXE
08M
cb
a
22K
Figure 5-131. The schematic of a test circuit for the PICAXE 08M shows the underside of
the stereo socket, the essential 10K and 22K resistors on the input pin, and an LED to
show an output from the chip.
Be aware that the PICAXE manual shows things differently (although I have
retained their labeling convention for the parts of the socket and the parts of
the plug, identified as a, b, and c).
One little detail about the socket that is commonly supplied for use with the
PICAXE: typically it has two pairs of contacts for the connections labeled b and
c in the manual, and in my diagram. When you solder a connection, your sol-
der joint should include both of the contacts in each pair, as shown in Figure
5-132.
Remember that the PICAXE must have 5 volts DC, and remember that your
voltage regular will deliver this voltage reliably only if you give it extra voltage
on its input side. If you provide it with 9 volts, that will provide a good amount
of headroom.
The 22K and 10K resistors are essential for using the chip; see the following
warning note for an explanation. My schematic also includes an LED and
a 330Ω resistor, but they are needed only for the test that we’ll be making
momentarily.
Pin 2 Pull-Down
Always include the 22K resistor and
the 10K resistor in the configura-
tion shown in Figure 5-131. These
resistors apply correct voltage to the
serial connection, and when you’re
using the PICAXE on its own, they pull
down the voltage on pin 2.
If pin 2 is left unconnected (floating),
it may pick up random voltages,
which the chip can misinterpret as a
new program or other instructions,
with unpredictable and undesirable
results.
The 22K and 10K resistors should be
regarded as permanent items ac-
companying your PICAXE regardless
of whether you have it attached to
your computer.

Chapter 5300
In from
Computer
Out to
Computer
Negative
Power
Figure 5-132. Correct wiring of the socket is essential. When soldering wires to
the lower terminals, make sure that you attach the wires to both of the terminals
in each pair.
Figure 5-133. The breadboard version of the test
schematic, with the plug of the USB download
cable inserted in the socket on the board. The
PICAXE chip can now receive a downloaded pro-
gram, and will immediately start to execute it.
Verifying the Connection
Follow these steps carefully every time you want to program or reprogram
your PICAXE chip:
1. Insert the USB plug of your PICAXE cable into the same USB port that you
used before.
2. Start the Programming Editor (or AXEpad if you are using a Mac OS or
Linux).
3. In the Programming Editor, select View→Options to verify that the editor
is using the right COM port and is expecting the 08M PICAXE chip.
4. Plug the stereo plug on the free end of the USB cable into the stereo sock-
et that is now wired into your breadboard. See Figures 5-133 and 5-134.
5. Check your wiring, and then connect your power supply to the breadboard.
6. Click the button labeled “program” in the Program Editor window to tell
the software to look for the PICAXE.
What If It Doesn’t Work?
The first thing to do is pull out the plug of the USB cable from the PICAXE
breadboard, leaving the other end of the cable attached to your computer. Set
your multimeter to measure DC volts, and attach its probes to sections b and c
of the plug. See Figure 5-135. Now click the“program”button again, and your
meter should show 5 volts briefly coming out of your computer to the plug on
the end of the cable.
Figure 5-134. After the program has been
downloaded, the plug can be removed,
and the program will continue to run,
causing the LED to continue flashing.

What Next? 301
If you detect the voltage, the software is installed and working properly. In
that case, there’s a problem on your breadboard, either in the chip or in the
wiring around it.
If you cannot detect any voltage, the software probably wasn’t installed prop-
erly, or is looking for the wrong serial port.Try uninstalling it and reinstalling it.
Your First Program
Finally you’re ready to create your first program. Type the following code into
the Programming Editor window:
main:
high 1
pause 1000
low 1
pause 1000
goto main
Be sure to include the colon after the word “main” on the first line. See Figure
5-136 for a screenshot. The indents are created by pressing the Tab key. Their
only purpose is to make program listings more legible. The software ignores
them.
Figure 5-136. This screenshot shows the first test program as it should be displayed by the
Programming Editor (on a Windows computer).
Click the Program button in the Programming Editor to download this program
into the chip. As soon as the download is complete, the chip should start flash-
ing the LED, lighting it for 1 second and then switching it off for 1 second. Figure
5-137 shows the steps that you should have followed to program the chip.
Now for the interesting part: disconnect the USB cable from the breadboard.
The chip should continue flashing.
Disconnect the power supply from the breadboard and wait a minute or two
for the capacitors to lose their charge. Reconnect the power, and the chip will
start flashing again.
The program that you downloaded to the chip will remain in the memory in-
side the chip and will begin running every time power is applied to the chip.
a: To computer
b: From computer
c: Negative power
Figure 5-135. The stereo plug on the end of
the USB download cable can be used for
fault tracing. A multimeter set to measure
DC volts can be attached to sections b and
c of the plug to establish whether the Pro-
gramming Editor is sending data through
the serial connection.
Type a program
using the
Program Editor
Click the
PROGRAM button
to download it
The PICAXE
starts running
the program
You can now
unplug the
stereo plug
Figure 5-137. Four steps to create and run a
program on the PICAXE controller chip.

Chapter 5302
Decoding the Code
Let’s take a look at the little program that you typed in. The first line identifies
a section of the program. This program only has one section, and we’re calling
it“main.”Any word with a colon after it is the name of a section of a program:
main:
The second line tells the chip to send a high output from Logic Pin 1:
high 1
The third line of the program tells the chip to wait for 1,000 milliseconds. This
of course is the same as one second:
pause 1000
The fourth line tells the chip to change Logic Pin 1 back to its low state:
low 1
The fifth line tells the chip to wait for another 1,000 milliseconds:
pause 1000
The last line tells the chip to go back to the beginning of the“main”section:
goto main
1
2
3
4 5
6
7
8
PICAXE
08M
(Logic Pin 0)
Logic Pin 1
Logic Pin 2
Logic Pin 4
Logic Pin 3
Figure 5-138. The conventional pin numbers of the PICAXE chip are incompatible with the
numbering system that is used in the PICAXE programming language. To minimize confu-
sion, this guide refers to “Logic Pins” when using the numbering system that is required
for programming the chip.
In from Computer
Out to Computer
Digital Output Pin0
Infra-Red Output
Digital Output Pin1
Digital Input Pin1
Analog-Digital Converter Pin1
Digital Output Pin2
Digital Input Pin2
Motor Power Output Pin2
Tune Output
Digital Output Pin4
Digital Input Pin4
Digital Input Pin3
Infra-Red Input
1
2
3
4 5
6
7
8
PICAXE
08M
Figure 5-139. Many of the pins on the PICAXE 08M have multiple functions, which can be
selected by appropriate program instructions.
The program doesn’t use the usual
pin numbers on the chip. It uses
what I will call “logic pin numbers.”
Figure 5-138 shows how they are
numbered. Figure 5-139 shows their
multiple functions. I have put Logic
Pin 0 in parentheses because its main
purpose is to send data to the com-
puter through the USB cable. It can
do double duty as a digital output,
but you have to disconnect it from
the USB cable first. It’s easy to forget
to do this. It’s a hassle that I prefer to
avoid.

What Next? 303
Editing
What if you want to change the program? No problem! Use the Programming
Editor to change one of the lines in the program. Substitute 100 instead of
1000 milliseconds, for instance. (The pause command can be followed by any
number up to 65535.) In your program, don’t use a thousands comma in any
of the numbers that you specify.
Plug the USB cable into the breadboard again, hit the Program button on the
screen, and the new version of the program will be automatically downloaded
to the chip, overwriting the old version.
What if you want to save the program for future use? Just go to the File menu
in the Programming Editor and save the program onto your computer’s hard
drive. Because the PICAXE uses a variant of the BASIC computer language, it
adds a .bas filename extension.
Simulation
If you make a simple typing error, the Programming Editor will find it and stop
you from downloading your program. It will leave you to figure out how to fix
the line that contains the error.
Even if all the statements in your program are correctly typed, it’s a good idea
to run a simulation of what they’ll do, before you download them.This is easily
done: click the“simulate”button on the menu bar of the Programming Editor.
A new window will open, displaying a diagrammatic view of the PICAXE chip
and showing you the states of its pins. (Note that if you use very short pause
commands, the simulation won’t run fast enough to display the time accu-
rately.) A simulation screenshot is shown in Figure 5-140.
The button at the bottom-right corner of the simulation window will open
up a list of all the variables in your program. So far, it doesn’t have any vari-
ables, but it soon will. All the zeros on the righthand side are binary numbers,
which you can ignore for now.
Figure 5-140. This screenshot shows the simulation window that
can be opened in the Program Editor to test program code before it
is downloaded to the chip. The values of variables are shown in the
section on the right. The pin states are shown on the left.
You’ll need to check the second
part of the PICAXE documentation,
which contains all the programming
statements and their correct syntax.
At the time of writing, this is stored
at http://www.rev-ed.co.uk/docs/
picaxe_manual2.pdf.

Chapter 5304
Loops
Here’s another thing I’d like you to try. Rewrite your program code as shown
here and download it onto the PICAXE:
main:
for b0 = 1 to 5
high 1
pause 200
low 1
pause 200
next
wait 2
goto main
Note that b0 is letter b followed by a zero, not letter b followed by letter O. The
extra indents once again are added to make the listing easier to understand.
The four lines beginning“high 1”and ending“pause 200”will be executed re-
peatedly. It’s helpful to see them as a block.
Watch the light and see what happens. It should flash five times quickly, then
wait for two seconds, and then repeat. You just added a loop to your program.
You can use a loop if you want something to happen more than once.
b0 is known as a variable. Think of it as being like a little“memory box”with its
name, b0, on a label on the outside. Figure 5-141 illustrates this concept. This
particular memory box can contain any number from 0 through 255. The loop
begins by telling the computer to put number 1 in the box, then process the
remaining statements, until the word “next” sends the processor back to the
first line, at which point it adds 1 to the contents of b0. If the value of b0 is 5 or
less, the loop repeats. If the value is 6, the loop has run five times, so it’s over,
and the PICAXE skips down to the “wait 2” statement after “next.” See Figure
5-142 for an annotated version of the program listing.
“Wait” is a PICAXE command that is measured in whole seconds, so “wait 2”
waits for 2 seconds. Then“goto main”begins the procedure all over again.
If your flashing-light demo worked out as planned, it’s time to take the next
step and make the chip do something more useful.
Go back to the beginning
and start all over again.
Label identifying
this piece of the program.
Use b0 to count
from 1 to 5.
Has b0 reached 6 yet?
If so, skip down beyond
the next statement.
Go back to line 2
and add 1 to b0.
Obey these
instructions
five times.
Figure 5-142. The blue annotations explain what the program, on the right, is telling the
PICAXE to do.
Figure 5-141. To understand how a program
works, visualize a variable as being like a
“memory box” with its name on the out-
side and a number stored on the inside.

What Next? 305
Fundamentals
Basic PICAXE parameters
Here are some of the most useful parameters of the PICAXE:
• The PICAXE requires 5 volts DC, regulated.
• The inputs and outputs of the PICAXE are compatible
with 5-volt logic chips. You can attach them directly.
• Each PICAXE pin can sink or source up to 20mA. The
whole chip can deliver up to 90mA. This means that
you can run LEDs directly from the pins, or a piezo
noisemaker (which draws very little current), or a
transistor.
• You can use a chip such as the ULN2001A Darlington
array (mentioned in the previous experiment) to am-
plify the output from the PICAXE and drive something
such as a relay or a motor.
• The chip executes each line of your program in about
0.1 milliseconds.
• The 08M chip has enough flash memory for about 80
lines of program code. Other PICAXE chips have more
memory.
• The PICAXE provides 14 variables named b0 through
b13. The“b”stands for“byte,”as each variable occupies
a single byte. Each can hold a value ranging from 0
through 255.
• No negative or fractional values are allowed in
variables.
• You also have 7 double-byte variables, named w0
through w6. The“w”stands for“word.”Each can hold a
value ranging from 0 through 65535.
• The“b”variables share the same memory space as the
“w”variables. Thus:
• b0 and b1 use the same bytes as w0.
Therefore, if you use w0 as a variable, do not use b0 or
b1. If you use b6 as a variable, do not use w3, and so on.
• Variable values are stored in RAM, and disappear when
the power is switched off.
• The program is stored in nonvolatile memory, and
remains intact when the power is off.
• The manufacturer’s specification claims that the
nonvolatile memory is rewritable up to about 100,000
times.
• If you want to attach a switch or pushbutton to a pin
and use it as an input, you should add a 10K pull-down
resistor between the pin and the negative side of the
power supply to hold the pin in a low state when the
switch is open. Figure 5-143 shows how pull-down
resistors should be used in conjunction with a SPST
switch or a pushbutton.
• On the 08M chip, if you apply a varying resistance
between Logic Pins 1, 2, or 4, and the negative side of
the power supply, the chip can measure it and“decide”
what to do. This is the“Analog-Digital Conversion”
feature—which leads to our next experiment.
10K10K
1
2
3
4 5
6
7
8
PICAXE
08M
Figure 5-143. The PICAXE can respond to the state of a switch
or button attached to any of its input-capable pins. A 10K resis-
tor must be used to pull down the state of the pin when the
contact of the switch or button is open. Otherwise, you may
get unpredictable results.

Chapter 5306
Often we want a microcontroller to measure something and respond in an
appropriate way. For instance, it can measure a low temperature and sound an
alarm, as I suggested in the example that I gave earlier.
The PICAXE has three analog-to-digital converters (ADCs) built in, accessible
via logic pins 1, 2, and 4, as shown in Figure 5-139. The best way to use them is
by applying a potential somewhere between 0 and 5 volts. In this experiment,
I’ll show you how to calibrate the response of the chip.
You will need:
• Trimmer potentiometer, 2K. Quantity: 1.
• PICAXE 08M chip and associated USB cable and socket. Quantity: 1 of
each.
Procedure
Take the same trimmer potentiometer that you used in Experiment 32 and
wire its center terminal to Logic Pin 2 of the PICAXE (which is hardware pin
5). The other two terminals of the 2K trimmer go to positive and to negative,
respectively. So depending how you set the trimmer, the pin of the PICAXE is
directly connected to positive (at one end of the scale), or directly connected
to negative (at the other end of the scale), or somewhere in between. See Fig-
ure 5-144 for the revised schematic, and Figure 5-145 for a photograph of the
breadboarded circuit.
330
2K
10K
1
2
3
4 5
6
7
8
PICAXE
08M
cb
a
22K
Figure 5-144. This schematic, drawn in a layout suitable
for breadboarding, shows how a 2K potentiometer can be
used to apply a varying voltage to one of the pins of the
PICAXE that is capable of converting an analog signal to a
digital value.
Figure 5-145. The trimmer potentiometer added to the previ-
ously breadboarded circuit.

What Next? 307
Now we need a program to tell the chip what to do. Using the Programming
Editor, start a new document. The code should look like this:
main:
readadc 2,b0
debug b0
goto main
The command “readadc 2,b0” means “read the analog input on Logic Pin 2,
convert from analog to digital, and store the result in b0.”
The command“debug b0”tells the chip to go into program debugging mode,
in which it uses its USB cable to tell the Programming Editor the values of all
the variables while the program is running. The variables are displayed in a
debugging window.
Download the program, and as the program starts to execute, the debugging
window should open. Start adjusting the trimmer while looking at the value of
b0, and you’ll see b0 change its value.
You can make a table and draw a graph showing the relationship between the
resistance between Logic Pin 2 and ground, and the value of b0. Just pull the
trimmer off the breadboard, measure its resistance with a meter, then increase
its resistance by, say, 200Ω, put it back into the breadboard, and look at the
value of b0 again.
This is laborious, but calibrating equipment is always laborious—and in any
case, I decided to do it for you. The graph is shown in Figure 5-146. You can
also see the raw data numbers in the following table. I was pleased to find that
the PICAXE gives a very precise, linear response to the input voltage. In other
words, the graph is a straight line.
Figure 5-146. When an ADC input pin is hooked up to a 2K po-
tentiometer, which is connected across the same voltage that
powers the chip, you should find that the resistance between
the input pin and the negative side of the power supply gener-
ates the series of digital values shown on the graph. Note that
the potentiometer must have a 2K value, and the power supply
is assumed to be precisely 5 volts.
2000
1500
1000
500
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
190
200
210
220
230
240
250
Equivalent Value Created by PICAXE Analog-Decimal Converter
ResistanceinOhmsBetweenPinandNegativeGround

Chapter 5308
This table shows measurements made with PICAXE 08M controller.
Resistance (in ohms)
between the ADC
pin and the negative
supply
Equivalent digital
value
2000 255
1900 243
1800 230
1700 218
1600 205
1500 192
1400 179
1300 166
1200 154
1100 141
1000 128
900 115
800 102
700 90
600 77
500 64
400 51
300 38
200 26
100 13
0 0
Now we can modify the program to make it do something with the informa-
tion that it’s taking in:
main:
readadc 2,b0
let w1 = 5 * b0
high 1
pause w1
low 1
pause w1
goto main

What Next? 309
Notice what’s happening here. First we get a value in b0, and then on the next
line, we do some arithmetic with it. The asterisk means“multiply.”So the state-
ment says, “Take whatever value is in b0, multiply by 5, and transfer it to an-
other variable, w1.”We have to use a w variable, because when we multiply the
value of b0 by 5, we may get a number that is bigger than 255—too big to fit
into a byte variable.
Finally, we take variable w1 and use it with a “pause” statement instead of a
fixed number value. We’re saying to the PICAXE, “pause for whatever number
of microseconds you get by checking the value of w1.”
So the software checks a variable resistance, turns it into a number, and ap-
plies that number to adjust the flashing speed of the LED.
Think back to the need of the cart powered by stepper motors. It was supposed
to check two photoresistors, and adjust the speed of each motor accordingly.
Well, this PICAXE program is a step in that direction. It can measure voltage on
a pin and change the output frequency on another pin. If you had two PICAXE
chips, you could wire each of them to a photoresistor and a motor. Then you
could adjust the behavior of your cart by editing the second line in the pro-
gram, where it converts the value of b0 to the value of w1 which will be used in
the“pause”command to determine the number of pulses per second. Instead
of multiplying by 5 you could multiply by 7 or whatever number gives you the
result you need. This leads to an important conclusion: a big advantage of a
programmable chip is that you can make adjustments in software.
Because the PICAXE 08M actually has more than one ADC input, and has three
pins that can be used for output, you might wonder whether you could use
just the one chip to control both motors in response to inputs from two sen-
sors.The problem is that the three output pins on the 08M also function as the
three ADC input pins.You’d do better to buy one of the more advanced PICAXE
chips, such as the 18M, which has more pins to choose from. It uses the same
basic set of programming instructions, and doesn’t cost much more money.
Also, you should read the PICAXE documentation and look up the “pwmout”
command, which is short for “pulse-width modulation output,” but you can
think of as meaning “power motor output.”This is specifically intended to run
stepper motors. It establishes an output frequency of pulses that will continue
while the chip obeys other instructions in its program.

Chapter 5310
Fundamentals
Extra features
A complete guide to the 08M would fill a book of its own, and of course such
books already exist (just search the books section of Amazon.com for keyword
“picaxe”). But I’ll finish my introduction to the controller by listing some of its
extra capabilities, leaving you to look them up and explore them. Then I’m go-
ing to suggest one last experiment.
Interrupts
The PICAXE 08M allows you to set one“interrupt.”This feature tells the chip
to make a mental note that if a particular event occurs—such as a switch
applying voltage to one pin—it should stop doing whatever else it was
doing, and respond to the interruption.
Infrared
One pin on the PICAXE 08M can be used to receive infrared signals from
a TV-style remote that you can buy from the same suppliers that sell the
PICAXE itself. With an infrared sensor attached to the chip, you can issue
commands remotely. If you want to build a remote-controlled robot, the
chip is specifically designed with this in mind.
Servo motors
Every PICAXE chip has at least one pin that can send a stream of pulses to
control a typical servo motor. On the 08M chip, it’s Logic Pin 2. The width of
each pulse tells the motor how far to rotate from its center position before
stopping. A 555 timer can send this stream, but the PICAXE makes it easier.
You can search online for more information about servo motors, which are
especially useful for applications such as steering model vehicles, adjusting
the flaps on model airplanes, and actuating robots.
Music
The PICAXE has an onboard tone generator that can be programmed with
a“tune”command to play tunes that you write using a simple code.
Alphanumeric input/output
The“kbin”programming command is available in the PICAXE models 20X2,
28X1 and 28X2, and 40X1 and 40X2. You can plug a standard computer
keyboard into the chip, and it will read the keypresses. You can also attach
alphanumeric displays, but these procedures are nontrivial. For instance,
when you’re trying to figure out which key someone has pressed on a key-
board, your program has to contain a list of the special hexadecimal codes
that the keyboard creates.
Pseudorandom number generation
All PICAXE models can generate pseudorandom numbers using a built-in al-
gorithm. If you initialize the number generator by asking the user to press a
button, and you measure the arbitrary time that this takes, you can seed the
pseudorandom number generator with the result, and the pseudorandom
number generator will have a less repeatable sequence.
Visit http://www.rev-ed.co.uk/docs/picaxe_manual1.pdf to learn more.

What Next? 311
The combination lock that I described in Experiment 20 is especially appro-
priate for a microcontroller, because it requires a series of operations that
resemble a computer program. I’m going to show how this project can be re-
designed using a PICAXE 08M, and then leave it to you to consider how some
of the other projects in this book could be converted.
You will need:
• The same type of keypad and relay recommended in Experiment 20.
• A transistor or Darlington array to amplify the output from the PICAXE so
that it can drive the relay.
Getting the User Input
Any of the input pins on the PICAXE can sense a switch closing. The trouble
is that we only have three pins capable of doing this, and even the most ad-
vanced PICAXE chip has fewer than 10 such pins. So how can we attach a 10-
key keypad to the 08M?
I have a suggestion: attach various resistors to the keypad, so that each key
applies a different voltage to one of the ADC pins.Then use the ADC feature to
convert the voltage to a number, and use a table of possible numbers to figure
out which key is being pressed.This may not be the most elegant solution, but
it works!
The keypad can be wired as shown in Figure 5-147. The asterisk key is still be-
ing used to supply power, as in the original experiment, while the pound key
resets the relay at the end of your computing session, as before.
Current flows through a series of resistors, beginning with one that has a value
of 500Ω. Because this is not a standard value, you will either have to make it by
combining other resistors in series, or by presetting a trimmer potentiometer.
After that, each button is separated from the next button by a 100Ω resistor.
Finally, at the end of the chain, a 600Ω resistor separates the last button from
the negative side of the power supply. Again, this is not a standard value, and
you may have to use a trimmer.
Add up all the resistances and you have 2K, which is the range that the PICAXE
wants us to use.When you press a button, you tap into the chain of resistances.
Button 9 puts 600Ω between the PICAXE ADC pin and ground. Button 6 is 700Ω,
button 3 is 800Ω, and so on. (You may prefer to lay out the buttons so that the
resistance progresses in a more logical fashion. That’s up to you. I chose to lay
them out in the way that would be easiest to visualize on a keypad.)
Now look back at the ADC values that I supplied in the table on page 308.These
are the values that you should get when you press various keypad buttons—
but you cannot count on them being absolutely precise, because they may
vary if your resistor values are not quite accurate, or if your power supply isn’t
exactly 5 volts. It’s not safe to say, for example, that the PICAXE will deliver an
ADC conversion value of precisely 77 when the resistance is 600Ω. It’s safer to

Chapter 5312
say that the value will be between 71 and 83. If we specify a range as shown in
the following table, we have a much better chance of interpreting each button
correctly.
Button number Range
9 600 71–83
6 700 84–96
3 800 97–108
0 900 109–121
8 1000 122–134
5 1100 135–147
2 1200 148–160
7 1300 161–172
4 1400 173–185
1 1500 191–198
Suppose you attach the common pin of your keypad to ADC Logic Pin 2 of the
PICAXE.You can now use the Program Editor to write a program that looks like
this:
getkey:
readadc 2,b0
let b1 = 9
if b0 84 then finish
let b1 = 6
let b1 = 3
let b1 = 0
let b1 = 8
let b1 = 5
let b1 = 2
let b1 = 7
let b1 = 4
let b1 = 2
finish:
return
What does the word“return”mean at the end? I’ll get to that in a second. I want
to explain the rest of the routine first.

What Next? 313
b0 receives the value supplied by the analog-digital converter when it looks at
the keypad. After storing the number in b0, the routine has to figure out which
keypad key it matches. The key identity (0 through 9) will be stored in another
variable, b1.
The program starts by assigning value 9 to b1. Then it checks to see wheth-
er b0 84. This means “if b0 is less than 84.” If it is, then the routine tells the
PICAXE to “finish,” which means “jump to the finish: label.” But if b0 is not less
than 84, by default the PICAXE continues on to the next line, which makes a
second attempt at guessing which key has been pressed. It assigns number 6
to b1. Now there’s another if-then test—and so on. This process of reassigning
values to b1 stops only when it gets to the point where b0 is greater than a
number in the table.
If you’re familiar with other dialects of BASIC, this may seem a bit laborious to
you. You may wonder why we can’t use a statement such as this:
if b0 70 and b0 84 then b1 = 9
The answer is that PICAXE BASIC isn’t sufficiently sophisticated to allow this.
An if-then statement has to result in a jump to another section of the program.
That’s the only permitted outcome.
If you don’t have any prior programming experience, the routine may still
seem laborious to you, and perhaps a bit puzzling, too.This is understandable,
because you’re getting a crash course in software design without any formal
preparation. Still, the PICAXE Programming Editor can be a big help, because
it has its simulation feature. Before you can use this, though, you have to pre-
cede the routine that I just supplied with a control routine that you must type
above it. The screenshot in Figure 5-148 shows you how it should look.
0
1 2 3
4 5 6
7 8 9
#
*
Reset
relay
PICAXE
ADC pin
PICAXE power supply
500
600
100100
100100100100
100100100
Figure 5-147. A quick and simple way of attaching a keypad to provide numeric input to the
PICAXE uses a chain of resistors totalling 2,000Ω. When a button is pressed, it connects the
ADC input pin to a point in the chain. The resistance detected by the input pin can then be
converted by the program in the chip to determine which key has been pressed.

Chapter 5314
I have chosen an arbitrary combination of 7-4-1 for our combination lock. Us-
ing these numbers, the main section of the program looks like this:
main:
low 1
gosub getkey
if b17 then main
gosub getkey
if b14 then main
gosub getkey
if b11 then main
high 1
end
I should explain that the pair of symbols mean “is not equal to.” So the
fourth line of the program means,“if b1 is not equal to 7.”
The value of b1 is supposed to be 7 if the user is putting in the correct com-
bination. So if it’s not 7, the user has entered the wrong value, and the if-then
statement sends the PICAXE back to the beginning. In fact anytime the user
inputs a number that is not in the correct 7-4-1 sequence, the program sends
the PICAXE back to the beginning. This is the way the pure-hardware version
of this experiment was set up.
But what is this word “gosub”? It means “go to a subroutine.” A subroutine is
any sequence of program statements that ends with the instruction to“return.”
So “gosub getkey” tells the PICAXE to mark its current place in the program
while it skips to the getkey: section of code, which it obeys, until it finds the
word“return,”which returns it to the place from where it came.
The PICAXE continues in this fashion until it reaches the word“end.”I had to in-
sert the word“end”because otherwise the PICAXE will continue executing the
program and will fall into the subroutine. “End” stops it from doing so. Figure
5-148 shows a screenshot of the complete listing.
So—is that all? Yes, that’s it. If you enter the code into the Programming Editor
exactly as I have supplied it, you should be able to run it in simulation mode,
and in the simulation window, click the right-arrow beside Logical Pin A2 to
increase its value in steps. Each time you pass one of the values in the getkey:
subroutine, you should see the value for variable b1 change in the display.
This is really all you need to perform the functions of the combination lock.
When the PICAXE runs this program, it waits for the correct combination. If it
receives the combination, it sends the output from logical pin 1 high; other-
wise, logical pin 1 stays low.
The only additional item you need is a transistor or CMOS gate between logi-
cal pin 1 and the relay that unlocks the computer, because the PICAXE cannot
deliver enough current to operate the relay by itself.
Putting this procedure into a controller chip not only simplifies the circuit, but
offers another advantage: you can change the combination simply by rewrit-
ing the program and downloading the new version into the chip.

What Next? 315
Figure 5-148. This screenshot shows the complete
listing of a program to read a sequence of three
keypresses in conjunction with a combination lock.
If the sequence is correct, the PICAXE sends a high
output from one of its pins. If the sequence is incor-
rect, the program loops back to the beginning.
Fundamentals
Limitations of MCUs
The PICAXE does have some disadvantages. Its voltage
requirements alone restrict you from using it with the kind
of freedom of a 555 timer.
Also, although I can get an instant result by plugging a 555
timer into a breadboard and adding a couple of resistors
and a couple of capacitors, the PICAXE requires me to add
a download socket, hook it up to my computer, write a
program in the Programming Editor, and download the
program.
Some people don’t like writing software, or they have dif-
ficulty thinking in the relentlessly left-brain way that com-
puter programming requires. They may prefer the hands-on
process of assembling hardware.
Other people may have the opposite preference. This of
course is a matter of taste, but one thing we know beyond
all doubt is that computer programs often contain errors
that may not reveal themselves until weeks or months later.
The PICAXE, for instance, doesn’t protect you if a number
is assigned to a variable that exceeds the limit for that type
of variable. Suppose b1=200 and b2=60 and your program
tells the PICAXE:
let b3 = b1 + b2
The result should be 260, but byte-size variables can only
count up to 255. What happens? You will find that b3 ac-
quires a value of 4, without any warning or explanation. This
is known as an“overflow error,”which can be very difficult
to predict, because it happens at runtime, when external
factors are in control. The code looks perfectly good; the
Programming Editor doesn’t find any syntax errors; the
simulation behaves properly. But in the real world, days or
even months later, an unexpected set of circumstances re-
sults in an input that causes the overflow, and because the
code is residing inside the chip at this point, you may have a
hard time figuring out what on earth went wrong.
Software has its problems. Hardware has its advantages.

Chapter 5316
Fundamentals
Unexplored territory
If you’ve taken the time to complete most of the projects in this book with your
own hands, you have gained a very rapid introduction to the most fundamental
areas of electronics.
What have you missed along the way? Here are some topics that remain wide
open for you to explore. Naturally you should search online if they interest you.
The informal, learning-by-discovery approach that I have used in this book
tends to be light on theory. I’ve avoided most of the math that you’d be expect-
ed to learn in a more rigorous course on the subject. If you have mathematical
aptitude, you can use it to gain a much deeper insight into the way in which
circuits work.
I didn’t deal much with computer architecture, either. We didn’t go very far into
binary code, and you didn’t build a half-adder, which is a great way to learn how
computers function on the most fundamental level. Perhaps you should think
about assembling one.
I avoided going deeply into the fascinating and mysterious properties of
alternating current. Here again, some math is involved, but just the behavior of
current at high frequencies is an interesting topic in itself.
For reasons already stated, I avoided surface-mount components—but you
can still go into this area yourself for a relatively small investment, if you
like the idea of creating fascinatingly tiny devices. This may be the future of
hobby electronics, so if you stick with it, you’ll probably end up in the world of
surface-mount.
Vacuum tubes were not mentioned, because at this point, they are mainly of
historical interest. But there’s something very special and beautiful about tubes,
especially if you can enclose them in fancy cabinetwork. In the hands of a
skilled craftsperson, tube amplifiers and radios become art objects.
I didn’t show you how to etch your own printed circuit boards. This is a task that
appeals to only certain people, and the preparation for it requires you to make
very neat drawings or use computer software for that purpose. If you happen to
have those resources, you might want to do your own etching. It could be a first
step toward mass-producing your own devices.
I didn’t cover static electricity at all. High-voltage sparks don’t have any practi-
cal applications, and they entail some safety issues—but they are stunningly
impressive, and you can easily obtain the necessary information to build the
equipment. Maybe you should try.

What Next? 317
In Closing
Other Controllers
If you want something more powerful, a BASIC Stamp is the logical next step
after a PICAXE. the BASIC Stamp is so called because it originally looked like a
postage stamp. The BASIC Stamp has a larger vocabulary of commands and a
bigger range of add-on devices (including displays with graphical capability,
and a little keyboard that is specifically designed for use with the controller).
The BASIC Stamp is shown in Figure 5-149.
On the downside, you’ll find that everything associated with the BASIC Stamp
is a bit more expensive than in the PICAXE world, and the download procedure
isn’t quite as simple.
One of the more recent developments in the world of MCUs is the Arduino,
which is both sophisticated and powerful. It does require programming in
the C language. This language is a little more difficult to understand, and has
only the vaguest similarity to the syntax that is used in the PICAXE and BASIC
Stamp. On the other hand, because C dominates the larger world of comput-
ing, learning it might not be such a bad idea—and the Arduino offers some
truly amazing capabilities. Because it is so popular, there are also many soft-
ware tools, documentation, user forums, and many enthusatic hobbyists to
help you. Two other Make: Books titles that I mentioned previously, Getting
Started with Arduino and Making Things Talk, provide a great introduction.
In Closing
I believe that the purpose of an introductory book is to give you a taste of a
wide range of possibilities, leaving you to decide for yourself what you want to
explore next. Electronics is ideal for those of us who like to do things ourselves,
because almost any application—from robotics, to radio-controlled aircraft, to
telecommunications, to computing hardware—allows opportunities that we
can explore at home, with limited resources.
As you delve deeper into the areas of electronics that interest you most, I trust
you’ll have a satisfying learning experience. But most of all, I hope you have
lots of fun along the way.
Figure 5-149. The BASIC Stamp controller
consists of surface-mounted compo-
nents on a platform that has pins spaced
at 1/10-inch intervals, for insertion in a
breadboard or perforated board. This
component uses a version of BASIC that
is similar to the programming language of
the PICAXE, but has many more exten-
sions. The BASIC Stamp is available
for use with a wide range of peripheral
devices, including many alphanumeric
dot-matrix displays.

A
319
Online Retail Sources and
Manufacturers
This appendix contains URLs for companies mentioned as retail sources or
manufacturers, along with the commonly used name of the source and the
company name.
Colloquially used
name
Actual corporate or company name URL
3M Minnesota Mining and Manufacturing Co. http://solutions.3m.com/en_US/
Ace Hardware Ace Hardware Corporation http://www.acehardware.com
Advanced Micro Circuits Advanced Micro Circuits Corp http://www.advancedmicrocircuits.com
Akro-Mils Myers Industries, Inc. http://www.akro-mils.com
Alcoswitch Division ofTyco Electronics Corporation http://www.tycoelectronics.com/catalog/menu/en/18025
All Electronics All Electronics Corporation http://www.allelectronics.com
All Spectrum Electronics All Spectrum Electronics http://www.allspectrum.com
All-Battery.com Tenergy Corporation http://www.all-battery.com
Alpha potentiometers Alpha Products Inc. http://www.alphapotentiometers.net
ALPS pushbutton ALPS Electric Co., Ltd. http://www.alps.com
Amazon Amazon.com, Inc. http://www.amazon.com
Amprobe AmprobeTestTools http://www.amprobe.com
Arduino No corporate identity http://www.arduino.cc
ArtCity ArtCity http://www.artcity.com
AutoZone AutoZone, Inc. http://www.autozone.com
Avago AvagoTechnologies http://www.avagotech.com
BASIC Stamp Brand owned by Parallax, Inc. http://www.parallax.com
BITechnologies BITechnologies Corporation http://www.bitechnologies.com
BK Precision BK Precision Corp. http://www.bkprecision.com
Bussmann fuses Cooper Bussman, Inc. http://www.cooperbussmann.com
CK switch CoActiveTechnologies, Inc. http://www.ck-components.com
Chicago lighting CML InnovativeTechnologies http://www.cml-it.com
CraftAmerica Cardinal Enterprises http://www.craftamerica.com
Darice Darice Inc. http://www.darice.com

Appendix320
Colloquially used
name
DeWalt DeWalt IndustrialTool Company http://www.dewalt.com
Digi-Key Digi-Key Corporation http://www.digikey.com
Directed switches Directed Electronics Inc. http://www.directed.com
Doctronics Doctronics Educational Publishing http://www.doctronics.co.uk
eBay eBay Inc. http://www.ebay.com
Elenco Elenco Electronics Inc. http://www.elenco.com
Everlight Everlight Electronic Co. Ltd. http://www.everlight.com
Extech Extech Instruments Corporation http://www.extech.com
Fairchild Fairchild Semiconductor Incorporated http://www.fairchildsemi.com
FTM FTM Incorporated http://thefabricatorssource.com
Fujitsu Fujitsu America, Inc. http://www.fujitsu.com/us/
GB wire strippers Gardner Bender Inc. http://www.gardnerbender.com
Hobbylinc Hobbylinc Hobbies http://www.hobbylinc.com
Home Depot HomerTLC, Inc. http://www.homedepot.com
Ideal wire strippers Ideal Industries Inc. http://www.idealindustries.com
Jameco Jameco Electronics http://www.jameco.com
KJ Magnetics KJ Magnetics Inc. http://www.kjmagnetics.com
Kingbright Kingbright Corporation http://www.kingbrightusa.com
Kobiconn No web page found; use mouser.com
KVMTools KVMTools Inc. http://www.kvmtools.com
Lowe’s hardware LF, LLC http://www.lowes.com
Lumex Lumex Inc. http://www.lumex.com
McMaster-Carr McMaster-Carr Supply Company http://www.mcmaster.com
Megahobby Megahobby.com http://www.megahobby.com
Meter Superstore Division of SRS Market Solutions Inc. http://www.metersuperstore.com
Michaels craft stores Michaels Stores, Inc. http://www.michaelscrafts.com
Mill-Max Mill-Max Manufacturing Corp. http://www.mill-max.com
Mitutoyo Mitutoyo America Corporation http://www.mitutoyo.com
Motorola Motorola, Inc. http://www.motorola.com/us
Mouser electronics Mouser Electronics, Inc. http://www.mouser.com
Mueller alligator clip Mueller Electric Company http://www.muellerelectric.com
Newark Subsidiary of Premier Farnell plc http://www.newark.com
NKK switches Nihon Kaiheiki Industry Co. Ltd. http://www.nkkswitches.com
NXP semiconductors NXP Semiconductors http://www.nxp.com
Omron Omron Corporation http://www.omron.com
On Semiconductor Semiconductor Components Industries, LLC http://www.onsemi.com
Optek Subsidiary ofTT Electronics plc http://www.optekinc.com
Panasonic Panasonic ElectricWorks Corporation http://pewa.panasonic.com

Online Retail Sources and Manufacturers 321

Colloquially used
name
PanaVise Panavise Products, Inc. http://www.panavise.com
Parallax Parallax, Inc. http://www.parallax.com
Pep Boys Pep Boys-Manny, Moe and Jack http://www.pepboys.com
Philips Koninklijke Philips Electronics N.V. http://www.usa.philips.com
PICAXE Revolution Education Ltd. http://www.rev-ed.co.uk
Piedmont Plastics Piedmont Plastics, Inc. http://www.piedmontplastics.com
Plano storages boxes Plano Molding Company http://www.planomolding.com
Pomona test equipment Pomona Electronics Inc. http://www.pomonaelectronics.com
RadioShack RadioShack Corporation http://www.radioshack.com
Sears Sears Brands, LLC http://www.sears.com
SparkFun Electronics Sparkfun Electronics http://www.sparkfun.com
Stanley tools The StanleyWorks http://www.stanleytools.com
STMicroelectronics STMicroelectronics Group http://www.st.com
Texas Instruments Texas Instruments Incorporated http://www.ti.com
Tower Hobbies Tower Hobbies http://www.towerhobbies.com
Twin Industries Twin Industries http://www.twinind.com
Tyco Tyco Electronics Corporation http://www.tycoelectronics.com
Vaughan Vaughan Bushnell Mfg. http://hammernet.com/vaughan/
Velleman keyboards Velleman nv http://www.velleman.eu
Vishay Vishay Intertechnology Inc. http://www.vishay.com
Wal-Mart Wal-Mart Stores, Inc. http://www.walmart.com
Weller Division of Cooper Industries, LLC http://www.cooperhandtools.com/brands/weller/
X-Acto Division of Elmer’s Products, Inc. http://www.xacto.com
Xcelite Division of Cooper Industries, LLC http://www.cooperhandtools.com/brands/xcelite/
Xytronic Xytronic Industries Ltd. http://www.xytronic-usa.com

Acknowledgments
My association with MAKE magazine began when its editor, Mark Frauenfelder,
asked me to write for it. I have always been very grateful to Mark for his sup-
port of my work. Through him I became acquainted with the exceptionally
capable and motivated production staff at MAKE. Gareth Branwyn eventually
suggested that I might like to write an introductory guide to electronics, so I
am indebted to Gareth for initiating this project and supervising it as my edi-
tor. After I wrote an outline in which I described my idea for “Learning by Dis-
covery”and the associated concept that cutting open components or burning
them up can be an educational activity, MAKE’s publisher, Dale Dougherty,
uttered the memorable phrase, “I want this book!” Therefore I offer special
thanks to Dale for his belief in my abilities. DanWoods, the associate publisher,
was also extremely supportive.
The production process was swift, competent, and painless. For this I thank my
editor at O’Reilly, Brian Jepson; senior production editor Rachel Monaghan;
copyeditor Nancy Kotary; proofreader Nancy Reinhardt; indexer Julie Hawks;
designer Ron Bilodeau; and Robert Romano, who tweaked my illustrations.
Most of all I am indebted to Bunnie Huang, my technical advisor, who reviewed
the text in detail and knows a bunch of stuff that I don’t know. Any residual er-
rors are still my fault, even though I would prefer to blame them on Bunnie.
Thanks also to Matt Mets, Becky Stern, Collin Cunningham, Marc de Vinck,
Phillip Torrone, Limor Fried, John Edgar Park, John Baichtal, and Jonathan
Wolfe for helping out with some last-minute project testing.
Lastly I have to mention the genius of John Warnock and Charles Geschke,
founders of Adobe Systems and creators of the very beautiful PostScript lan-
guage, which revolutionized all of publishing.The horror of attempting to cre-
ate this book using graphic-arts tools from…some other company…is almost
unimaginable. In fact, without Illustrator, Photoshop, Acrobat, and InDesign, I
doubt I would have attempted the task. I am also indebted to the Canon 1Ds
with 100mm macro lens, which took many of the pictures in this book.
No free samples or other favors were received from any of the vendors men-
tioned herein, with the exception of two sample books from MAKE, which I read
to ensure that I was not duplicating anything that had already been published.

325
Index
Numbers
2N2222 transistor, 73
(see also Experiments 11 and 15)
2N6027 programmable unijunction
transistor (see Experiment 14:
A Pulsing Glow)
3M, 319
breadboard, 39
single inline sockets and headers,
103
9-volt battery, 5
12-key numeric keypad, 151
40xxB chip, 191
40xx chip, 191
74ACTxx chip, 191
74ACxx chip, 191
74AHCTxx chip, 191
74AHCxx chip, 191
74HC00 chip (see Experiment 22:
Flipping and Bouncing)
74HC00 quad 2-input NAND chip
(see Experiment 19: Learning
Logic)
74HC04 chip, 149
(see also Experiment 20: A
Powerful Combination)
74HC08 quad 2-input AND chip (see
Experiments 19 and 20)
Race to Place)
74HCTxx chip, 191
74HCxx chip, 191
74LS06 open-collector inverter chip,
150
74LS27 chip (see Experiment 23:
Nice Dice)
74LS27 triple-input NOR chip, 150
74LS92 chip, 216
74LS92 chip (see Experiment 23:
Nice Dice)
74LS92 counter chip, 150
74LVxx chip, 191
555 timer chip, 150
alternating current, 248
astable mode, 164–165
audio frequencies, 256
bistable configuration, 176–177
frequency in astable mode, 166
history, 160
limits, 161
monostable mode, 158–159
powering up in bistable mode, 225
pulse duration, 157
reset voltage, 156
square wave, 258
trigger voltage, 156
usefulness, 161
(see also Experiments 16-24, 29,
32-33)
4026 chip, 150
clock disable, 175
(see also Experiment 18: Reaction
Timer)
7400 family of integrated circuits,
192
A
ABS (acrylonitrile butadiene styrene)
cutting, 270
(see also Experiment 32: A Little
Robot Cart)
AC adapter, 39
modifying, 111
AC adapter plugs, 55–56
AC (alternating current), 12
Ace Hardware, 319
wire, 101
Advanced Micro Circuits, 319
Akro-Grids, 229
Akro-Mils, 229, 319
alarms
installation, 145–146
intrusion (see Experiments 11, 15,
and 24)
magnetic sensor switches, 128
Alcoswitch, 319
pushbutton, 42
All-Battery.com, 319
All Electronics, xii, 42, 319
12-key numeric keypad, 151
alligator clips, 4
battery holders and connectors, 4
desoldering wick, 98
jumper wire assortment, 41
patch cords, 41
project boxes, 102
solder, 100
soldering stand, 98
solder pump, 98
switches, 42

Index326
alligator clips, 4
copper, 101
All Spectrum Electronics, 319
LEDs, 4
Alpha potentiometers, 4, 319
ALPS pushbutton, 319
alternating current, 12, 248
Amazon, 319
deburring tool, 99
electronic solder, 100
GB Automatic Wire Strippers, 40
pick and hook set, 99
amperage, 10
Ampère, André-Marie, 13
amperes, 36
basics, 11
amplification, 87
amplifiers, 49
Amprobe, 319
amps, 11
Arduino, 319
microcontrollers, 227
ArtCity, 319
miniature hand saw, 99
The Art of Electronics, 235
audio amplifier (see Experiment 29:
Filtering Frequencies)
audio distortion (see Experiment 30:
Fuzz)
audio electronics, 227
AutoZone, 319
fuses, 4
Avago, 319
diodes, 103
B
Background
Clipping, 257
Early switching systems, 49
Father of electromagnetism, 13
From Boole to Shannon, 184–185
How chips came to be, 152
How much voltage does a wire
consume?, 27
How the timer was born, 160
Inventor of the battery, 12
Joseph Henry, 238
Logic gate origins, 192
Maddened by measurement, 124
Michael Faraday and capacitors, 64
Mounting a loudspeaker, 87
Origins of loudspeakers, 243
Origins of programmable chips,
294
Positive and negative, 35
Soldering myths, 106
Stomp-box origins, 260–261
The confusing world of TTL and
CMOS, 190–192
The man who discovered
resistance, 8
The origins of wattage, 28
Transistor origins, 78
Why didn’t your tongue get hot?,
10
banana plugs, 97
Bardeen, John, 78
BASIC Stamp microcontrollers, 227,
294, 317, 319
batteries, 3, 103
9-volt, 5
abusing (see Experiment 2: Let’s
Abuse a Battery!)
amperage, 10
ampere basics, 11
current, direct and alternating, 12
heat, 10
inventor, 12
lithium, 9, 30
making (see Experiment 5: Let’s
Make a Battery)
schematics, 53
voltage, 10
volt basics, 11
(see also Experiment 1: Taste the
Power!)
battery life, 123
Bell, Alexander Graham, 243
benders, plastic, 272
binary arithmetic, 217
binary code, 214–220
BI Technologies, 319
potentiometers, 4
BK Precision, 319
multimeter, 2
boardmount sockets and pinstrip
headers, 103
book sources, 234–235
Boolean logic, 184, 186
Boole, George, 184
Brattain, Walter, 78
breadboard alarm circuit, 135–136
breadboards, 39, 65–67
(see also Experiments 8, 20, and 21)
break-to-make transistor circuit,
129–130
brushed DC motor, 280
Burkard, Johann, 261
Bussmann fuses, 319
Buzbee, Bill, 192
C
calipers, 99
Camenzind, Hans, 160
capacitance, 3, 39, 64, 86, 133, 157,
180, 236, 246–248, 249, 252,
262
farad, 61
capacitors, 42, 61
basics, 62–63
diodes, 241
Faraday, Michael, 64
getting zapped by, 62
nonpolarized electrolytic
capacitors, 249
polarity, 63
time and (see Experiment 9: Time
and Capacitors)
time constant, 71–72
(see also Experiment 8: A Relay
Oscillator)
ceramic capacitors, 43
Chicago lighting, 319
chips, 147
74HC00 quad 2-input NAND chip
(see Experiment 19: Learning
Logic)
74HC00 (see Experiment 22:
74HC02 (see Experiment 22:
74HC04 (see Experiment 20: A
Powerful Combination)
74HC08 quad 2-input AND chip
(see Experiments 19 and 20)

Index 327

74HC32 (see Experiment 21: Race
to Place)
74LS06 open-collector inverter
chip, 150
74LS27 (see Experiment 23: Nice
Dice)
74LS27 triple-input NOR chip, 150
74LS92 counter chip, 150
74LS92 (see Experiment 23: Nice
Dice)
555 timer (see 555 timer chip)
4026, 150
(see also Experiment 18: Reaction
Timer)
choosing, 148–149
common part numbers, 193
floating pins, 175
history, 152
logic chips, 150
power supplies, 154
programmable chips, origins, 294
Churchill, Sir Winston, 29
circuit chips (see chips)
The Circuit Designer’s Companion,
235
CK
pushbutton, 42
switch, 319
clip-on meter test leads, 97
clipping, 257
CMOS chips, floating pins, 175
CMOS Sourcebook, 234
coil schematics, 238
coil voltage, 58
cold-weld, 106
combination lock circuit schematic,
198, 201
Common (COM) socket, 5, 6
Complementary metal–oxide
semiconductor (CMOS),
190–192
computers, 232
magnets, 240
conductor, 6
control knobs, 229
controller chips
limitations, 315
(see also Experiment 34: Hardware
Meets Software)
coulomb, 36
countersink, hand-cranked, 99
CraftAmerica, 319
crossover networks, 253–257
current
alternating, 248
checking flow, 21–25
direct and alternating, 12
transistors and, 80–81
D
Darice, 319
Darice Mini-Storage boxes, 230
Davies, Ray, 260
DC (direct current), 12
DC power plug, 103
DC stepper motor, 280
DeArmond, Harry, 261
deburring tool, 99, 271
decimals, 29
Dellepiane, Flavio, 260
DeWalt, 320
DeWalt XRP jigsaw, 271
diesel engine, 236
Digi-Key, xi, 320
patch cords, 41
diodes, 103, 134
capacitors, 241
schematics, 134
direct current, 12
Directed switches, 320
distortion (see Experiment 30: Fuzz)
Doctronics, 233, 320
Doing the math on your tongue, 30
double-throw switch, 42, 46
DPDT relay, 103
Dummer, Geoffrey W. A., 152
E
eBay, xii, 320
electrical potential, 36
electricity
magnetism, relationship, 236
nature of, 33
sound into, 244–245
electrolytic capacitors, 42, 61
electromagnetism, father of, 13
electromagnet (see Experiment 25:
Magnetism)
Electronics Club, 233
electronic solder, 100
electronics-tutorials.ws, 233
Elenco, 320
helping hand, 96
The Encyclopedia of Electronic
Circuits, 235
Essentials
All about diodes, 134
All about NPN and PNP transistors,
76–77
All about programmable
unijunction transistors, 83–84
Battery life, 123
Logic gate basics, 186–189
Perfboard soldering procedure,
137
Real-world fault tracing, 139
Transistors and relays, 79
Everlight, 320
low-power LEDs, 150
Experiment 1: Taste the Power!, 5–9
cleanup and recycling, 9
further investigation, 8
procedure, 7
tools, 5
Experiment 2: Let’s Abuse a Battery!,
9–13
procedure, 9–12
Experiment 3: Your First Circuit,
13–17
lighting LEDs, 16–17
setup, 13–15
Experiment 4: Varying the Voltage,
18–31
checking flow, 21–25
dimming LEDs, 19–25
manufacturer’s data sheet, 26
Ohm’s Law, 26
potentiometers, 18
size of resistor required by LED, 28
Experiment 5: Let’s Make a Battery,
32–38
practical purposes, 37

Index328
Experiment 6: Very Simple Switching,
43–54
connection problems, 45
schematics, 50–54
testing, 45–49
tools, 44–45
Experiment 7: Relay-Driven LEDs,
55–59
AC adapter plugs, 55–56
how it works, 59
operating current, 58
procedure, 59
Experiment 8: A Relay Oscillator,
60–67
adding capacitance, 61–64
breadboarding circuits, 65–67
Experiment 9: Time and Capacitors,
68–72
voltage, resistance, and
capacitance, 69–72
Experiment 10: Transistor Switching,
73–81
fingertip switching, 74–75
Experiment 11: A Modular Project,
82–93
amplification, 87–89
beyond persistence of vision,
86–87
enhancements, 92–93
pulsed output, 90–92
slow-speed oscillation, 85
wish list, 93
Experiment 12: Joining Two Wires
Together, 104–113
adding insulation, 110–111
first solder join, 104–107
modifying AC adapter, 111
second solder join, 108
shortening power cords, 111–113
Experiment 13: Broil an LED, 114–116
heat-sinking, 115
Experiment 14: A Pulsing Glow,
117–126
finishing, 121–126
procedure for building this circuit,
120
resizing the circuit, 119–120
Revisited, 127–146
alarm installation, 145–146
blocking bad voltage, 132–134
breadboard alarm circuit, 135–136
129–130
conclusion, 146
final test, 145
installing switches, 142–143
perfboarding, 136–139
self-locking relay, 131–132
soldering switches, 143–144
switches and inputs for alarm,
140–141
Experiment 16: Emitting a Pulse,
153–161
procedure, 153–162
Experiment 17: Set Your Tone,
162–169
astable modifications, 166–167
chaining chips, 167–170
Experiment 18: Reaction Timer,
170–181
counting, 171–174
delay, 178–179
display, 170–171
enhancements, 180
pulse generation, 175
refinements, 176
reflex tester, 179
summary, 181
Experiment 19: Learning Logic,
181–196
Experiment 20: A Powerful
Combination, 197–204
breadboarding, 200–201
computer interface, 202–203
enhancements, 203
incorrect inputs, 200
questions, 200
schematic, 198–199
Experiment 21: Race to Place,
205–210
breadboarding, 209–210
conceptual experiment, 205–209
enhancements, 210
goal, 205
(see also Experiment 36: The Lock,
Revisited)
Experiment 22: Flipping and
Bouncing, 211–213
how it works, 212–214
Experiment 23: Nice Dice, 214–222
binary code, 214–220
enhancements, 220–222
Completed, 223–226
delay before deactivation, 225–226
delayed activation, 223
keypad deactivation, 223–224
summary, 226
Experiment 25: Magnetism, 236–238
procedure, 236
Experiment 26: Tabletop Power
Generation, 239–241
Experiment 27: Loudspeaker
Destruction, 242–245
procedure, 242
Experiment 28: Making a Coil React,
246–248
Experiment 29: Filtering Frequencies,
249–256
adding an amplifier, 250–252
crossover networks, 253–257
procedure, 250
Experiment 30: Fuzz, 257–261
schematic, 258
Experiment 31: One Radio, No
Solder, No Power, 262–267
enhancements, 265
Experiment 32: A Little Robot Cart,
268–284
bending, 272–273
circuit, 276–281
curving cuts, 271
framing your cart, 274–276
making 90 degree joints, 273–274
making plans, 272
mechanical power, 281–284

Index 329

Experiment 33: Moving in Steps,
284–292
adding autonomy, 291
exploring your motor, 285–286
quick demo, 286–289
setting up light seeking robot,
291–292
speed control, 290–291
Experiment 34: Hardware Meets
Software, 293–305
decoding the code, 302
editing code, 303
first program, 301
loops, 304–305
simulation, 303
software installation and setup,
296–300
Programming Editor software,
297–298
setting up hardware, 298–300
USB driver, 296–297
troubleshooting, 300–301
verifying connection, 300
Experiment 35: Checking the Real
World, 306–310
Experiment 36: The Lock, Revisited,
311–317
other controllers, 317–318
user input, 311–315
(see also Experiment 21: Race to
Place)
Extech, 320
multimeter, 2
F
Fairchild, 320
integrated circuit chips, 150
transistor, 42
voltage regulators, 151
Faraday, Michael, 64
farad basics, 61
fault tracing, 139
Field, Simon Quellan, 265
flat-format storage boxes, 230
floating pins, 175
Formosa, Dan, 261
Franklin, Benjamin, 35
frequencies (see Experiment 29:
Filtering Frequencies)
FTM, 320
Fujitsu, 320
relays, 42
Fundamentals
555 timer chip frequency in astable
mod, 166
555 timer chip pulse duration in
monostable mode, 157
555 timer limits, 161
All about ABS, 269
All about limit switches, 278
All about motors, 280
All about perforated board, 116
All about switches, 46–48
Ampere basics, 11
A two-way relationship, 236
Basic PICAXE parameters, 305
Basic schematic symbols, 51–54
Capacitor basics, 62–63
Choosing chips, 148–149
Coil schematics and basics, 238
Common part numbers, 193
Counters and seven-segment
displays, 173
Decimals, 29
Decoding resistors, 14–15
Direct and alternating current, 12
Farad basics, 61
Inside a relay, 58
Limitations of MCUs, 315
Ohms, 6
Ohm’s Law, 26
PICAXE 08M extra features, 310
Rules for connecting logic gates,
194–195
Series and parallel, 25
Switch bounce, 174
The bistable 555 timer, 176–177
Unexplored territory, 316
Voltage regulators, 182
Volt basics, 11
Watt basics, 31
Where to find ABS, 269
Why the 555 is useful, 161
Wire gauges, 282
fuses, 4
fuzz box, 257, 260
G
galvanometer, 13
GB Automatic Wire Strippers, 40
GB wire strippers, 320
general-duty soldering iron, 30 to 40
watts, 96
Getting Started in Electronic, 235
Getting Started with Arduino, 234
Gibson Maestro Fuzz-Tone, 260
grounding yourself, 172
Guru’s Lair, 233
H
hand-cranked countersink, 99
hand saw, miniature, 99
headphone, high-impedance (see
Solder, No Power)
heat, 10
heat guns, 98
warning, 110
heat-shrink tube, 101
heat-sinking, 115
helping hand, 96
Henry, Joseph, 237, 238
high-impedance headphone (see
Solder, No Power)
high voltage, 263
Hobbylinc, 320
Home Depot, xii, 320
plywood, 102
wire, 101
hookup wire, 41
I
IC sockets, 150
Ideal wire strippers, 320
incandescent lightbulb, 53
inductance, 26, 237, 241
self-inductance, 246
inductive reactance, 246

Index330
insulated binding posts, 103
insulator, 6
integrated circuit chips (see chips)
intrusion alarm (see Experiments 11,
15, and 24)
J
jacks, 49
Jameco, 320
potentiometer, 42
solder, 100
joules, 36
jumper wire assortment, 41
K
Kellogg, Edward, 243
keypads
(see Experiment 20: A Powerful
Combination)
Kilby, Jack, 152
Kingbright, 320
Kinks, 260
KJ Magnetics, 320
Kobiconn, 320
Kronus Automatic Wire Strippers, 40
KVM Tools, 320
deburring tool, 99
L
labeling, 231
Lancaster, Don, 233
latching relays, 151
leads, 5
LED numeric displays, 150
LEDs, 4
dimming, 19–25
lighting, 16–17
low-powered, 150
pulsing (see Experiment 14: A
Pulsing Glow)
relay-driven (see Experiment 7:
Relay-Driven LEDs)
schematics, 53, 54
size of resistor required, 28
too much heat (see Experiment 13:
Broil an LED)
lemon battery, 32–38
lightbulb, 53
light-emitting diodes (see LEDs)
lightning, 35
limit switches, 278
lithium batteries, 9, 30
LM7805 voltage regulator (see
Experiment 19: Learning
Logic)
logic chips, 150
logic gates
basics, 186–189
origins, 192
rules for connecting, 194–195
(see also Experiments 19-24)
loudspeakers, 43, 104
amplification, 87
mounting, 87
origins, 243
sound into electricity, 244–245
(see also Experiments 17, 27, and
29)
Lowe’s hardware, xii, 320
plywood, 102
wire, 101
Lumex, 320
diodes, 103
M
machine screws, 102
magnetism and electricity,
relationship, 236
magnetism generating electricity
(see Experiment 26: Tabletop
Power Generation)
magnets
warnings, 240
magnifying lens, 96
mail-order sources, xi
Make: Electronic kits, xiii
Maker Shed, xiii
Making Things Talk, 234
manufacturer’s data sheet, 26
Marconi, Guglielmo, 266
McMaster-Carr, xii, 230, 320
deburring tool, 99
hand-cranked countersink, 99
hookup wire, 41
soldering iron, 96
MCUs
limitations, 315
(see Experiment 34: Hardware
Meets Software)
measurements, 36
conversion table, 124–126
in inches, 124
Megahobby, 320
miniature vise, 99
Meter Superstore, 97, 320
metric system, 124
Michaels craft stores, 229, 320
microcontrollers, 227
PICAXE (see PICAXE)
microfarads, 61
Mill-Max, 320
103
miniature screwdriver set, 98
miniature vise, 99
Mitutoyo, 320
calipers, 100
Motorola, 320
transistor, 42
motors, 227, 280
stepper (see Experiment 33:
Moving in Steps)
Mouser Electronics, xi, 320
potentiometers, 4
moving-coil microphone, 244
Mueller alligator clips, 101, 320
multimeter, 2
mutual repulsion, 33
N
NAND gates (see Experiments 19-24)
nanofarads, 61
negative charge, 35
neodymium magnet, 240
Newark, xii, 320

Index 331

Newark Electronics
Vectorboard, 101
newtons, 36
NKK switches, 320
noisemaking circuit, 92
nonpolarized electrolytic capacitors,
249
nonpolarized relays, 58
NOR gates, 212
Noyce, Robert, 152
NPN and PNP transistors, 76–77, 79,
258
numeric keypads
(see Experiment 20: A Powerful
Combination)
NXP semiconductors, 320
O
Ohm, Georg Simon, 8
ohms, 6
Ohm’s Law, 25, 26, 30, 283
Omron, 320
relays, 42
online sources, 233
On Semiconductor, 320
transistor, 42
open-collector inverter chip, 150,
222
operating current, 58
Optek, 320
diodes, 103
oscillator, relay (see Experiment 8: A
Relay Oscillator)
oscilloscope, 231
P
Panasonic, 320
PanaVise, 321
panel-mounted power jack, 103
Parallax, 321
patch cords, 41
pencil-type 15-watt soldering iron, 96
Pep Boys, 321
perforated boards, 101, 116, 136–
139
common errors, 138
soldering procedure, 137
P. H. Anderson, 295
Philips, 321
photoresistors (see Experiment 33:
Moving in Steps)
PICAXE, 227, 321
alphanumeric input/output, 310
infrared, 310
interrupts, 310
limitations, 315
origins of programmable chips, 294
pseudorandom numbers, 310
servo motor, 310
tone generator, 310
(see also Experiments 34-36)
picofarads, 61
Piedmont Plastics, 321
pin-shuffling, 161
Plano, 229
Plano storages boxes, 321
plastic benders, 272
pliers, 1
plywood, 102
PNP transistors (see NPN and PNP
transistors)
point-to-point wiring connections,
106
Pomona
test equipment, 321
positive charge, 35
potentiometers, 4, 42, 151, 229, 249
schematics, 53
(see also Experiments 4, 32, and 35)
power assessments, 31
power connectors, 229
power cords, shortening, 111–113
power outlet, 12
power supplies, 39, 231
chips, 154
Practical Electronics for Inventors,
234
Programmable Intelligent Computer
(PIC), 294
Programmable Interface Controller
(PIC), 294
programmable microcontrollers, 227
project boxes, 102
Prolatch, 230
prototyping board, 101
PSP breadboard, 39
pushbuttons, 42
options for toggle switches and
pushbuttons, 47
PUTs (programmable unijunction
transistors)
2N6027 (see Experiment 14: A
Pulsing Glow)
schematics, 83
R
radio-frequency devices, 227
radio, how it works, 266–267
RadioShack, xi, 103, 321
alligator clips, 4, 101
breadboard, 39
fuses, 4
heat-shrink tube, 101
helping hand, 96
hookup wire, 41
IC sockets, 150
insulated binding posts, 103
Kronus Automatic Wire Strippers, 40
LEDs, 4
loudspeaker, 43
magnifying lens, 96
panel-mounted power jack, 103
perforated board, 101
pliers, 1
potentiometer, 42
power supply/universal AC
adapter, 39
project boxes, 102
resistors, 4
solder, 100
soldering iron, 96
soldering stand, 98
transistor, 42
wire cutters, 2

Index332
reactance, 246
reference sources, 233–235
books, 234–235
online, 233
relay-driven LEDs (see Experiment 7:
Relay-Driven LEDs)
relay oscillator (see Experiment 8: A
Relay Oscillator)
relays, 42, 56–58
coil voltage, 58
inside, 58
latching, 151
nonpolarized, 58
set voltage, 58
switching capacity, 58
transistors and, 79
reset voltage, 156
resistance, 25, 246
discovery of, 8
larger, 10
measuring, 6
(see also Experiment 1: Taste the
Power!)
resistors, 4, 43
decoding, 14–15
hot, 247
in parallel, 25
in series, 25
power assessments, 31
schematics, 52
(see also Experiment 3: Your First
Current)
Rice, Chester, 243
Richards, Keith, 260
robotics, 227
(see Experiments 32 and 33)
Rolling Stones, 260
S
saw, miniature, 99
schematics, 50–54
4026 chip, 171
batteries, 53
coil, 238
combination lock circuit, 198, 201
diodes, 134
dots, 51
Experiment 20: A Powerful
Combination, 198–199
Experiment 30: Fuzz, 258
incandescent lightbulb, 53
LEDs, 53, 54
potentiometer, 53
PUTs, 83
resistors, 52
switches, 51
symbols, 51
wires, 52
Scitoys Catalog, 265
screwdriver set, miniature, 98
screws, 102
tamper-proof, 203
Scribner, Charles E., 49
Sears, 321
deburring tool, 99
self-inductance, 246
servo motor, 280
PICAXE, 310
set voltage, 58
Shannon, Claude, 184
Shockley, William, 78, 152
short circuits, 9
Siemens, Ernst, 243
signal diodes, 134
sine wave, 255
103
single-pole, double-throw switch
(SPDT), 46
single-pole, single-throw switch
(SPST), 46
single-pole switch, 42
single-throw switches, 46
sockets, 49
solder, 100
soldering
alternatives, 106
desoldering, 109
errors, 107
myths, 106
switches, 143–144
theory, 109
(see also Experiment 12: Joining
Two Wires Together)
soldering irons, 96
warning, 104
soldering stand, 98
solder pump, 98
sound into electricity, 244–245
SparkFun Electronics, 321
sparking, 48
SPDT toggle switch, 103
square wave, 258
Stanley, 321
wire cutters, 2
stepper motors
inside, 288–289
(see also Experiment 33: Moving in
Steps)
STMicroelectronics, 321
logic chips, 150
transistor, 42
stomp-box origins, 260–261
storage containers, 229
switch bounce, 174
switches, 42, 46–48
checking, 48
double-pole switches, 46
double-throw switch, 46
early systems, 49
installing for alarm, 142–143
limit, 278
pushbuttons, 47
relays and, 103
schematics, 51
simple (see Experiment 6: Very
Simple Switching)
single-pole, double-throw switch
(SPDT), 46
single-pole, single-throw switch
(SPST), 46
single-throw switches, 46
soldering, 143–144
sparking, 48
tactile, 151
switching capacity, 58
switching transistors (see
Experiment 10: Transistor
Switching)

Index 333

T
tactile switches, 151
tamper-proof screws, 203
tantalum capacitor, 63
Texas Instruments, 321
4026 Decade Counter, 150
logic chips, 150
Theory
Alternating current concepts, 248
Basic measurements, 36
Binary arithmetic, 217
Calculating voltage drop, 283–284
Doing the math on your tongue, 30
How radio works, 266–267
Inductance, 237
Inside a stepper motor, 288–289
Inside the 555 timer: astable mode,
164–165
Inside the 555 timer: monostable
mode, 158–159
Power assessments, 31
See the current, 80–81
Soldering theory, 109
Sound, electricity, and sound,
244–245
The nature of electricity, 33
The time constant, 71–72
Waveforms, 255–256
third hand, 96
Thomson, J. J., 35
time constant, 71–72
toggle switches, 42, 229
pushbuttons, 47
Tools
Desoldering, 109
Eight most common soldering
errors, 107
Four most common perfboarding
errors, 138
torque, 281
Tower Hobbies, 321
tracing a fault, 139
transistors, 42
2N2222 (see Experiments 11 and 15)
2N6027 programmable unijunction
transistor (see Experiment 14:
A Pulsing Glow)
basics, 77
beta value, 80
129–130
getting a better understanding,
80–81
NPN and PNP, 76–77
origins, 78
relays and, 79
switching (see Experiment 10:
Transistor Switching)
unijunction, 82–84
Transistor-Transistor Logic (TTL),
190–192
tremolo box, 261
Trem-Trol, 261
trigger voltage, 156
TTL Cookbook, 234
tweeter, 253
Twin Industries, 321
perforated board, 101
Tyco, 321
relays, 42
U
unijunction transistors, 82–84
V
Vaughan, 321
Vectorboard, 101
Velleman keyboards, 321
Ventures, 260
VIH min, 192
VIL max, 192
vise, miniature, 99
Vishay, 321
VOH min, 192
VOL max, 192
Volta, Alessandro, 12
voltage, 10
blocking bad voltage, 132–134
calculating drop, 283–284
high, 263
how much wire consumes, 27
measuring, 6
voltage regulators, 151, 182
LM7805 (see Experiment 19:
Learning Logic)
volts, 36
basics, 11
Vox wow-fuzz pedal, 257
W
Wal-Mart, 229, 321
Warnings
Avoid Burns While Bending, 272
Beware of Pin-Shuffling!, 161
Blood Blisters and Dead Media, 240
Capacitor Polarity, 63
Cut with Care, 270
Flying Wire Segments, 121
Getting Zapped by Capacitors, 62
Grounding Yourself, 172
Heat Guns Get Hot, Too!, 110, 111
High Voltage!, 263
Hot Resistors, 247
Never Use Two Hands, 74
No Floating Pins!, 175
No More Than 9 Volts, 5
Pin 2 Pull-Down, 299
Short Circuits, 9
Soldering Irons Get Hot!, 104
The Warranty Issue, 197
water-powered turbine, 236
wattage, history, 28
Watt, James, 28
watts, 36
basics, 31
waveforms, 255–256
clipping, 257
wavelength of the sound, 244
Weller, 321
Weller Therma-Boost, 96
windmill, 236
wire cutters, 2
warning, 121
wire gauges, 282
wires, 100
point-to-point wiring connections,
106
schematics, 52
soldering (see also Experiment 12:
Joining Two Wires Together)
voltage consumed by, 27

Index334
wire strippers, 40
wire wrap, 106
woofer, 253
work area, customizing, 228–232
bench, 231
computer, 232
labeling, 231
oscilloscope, 231
X
X-Acto, 321
Xcelite, 321
pliers, 1
Xytronic, 321
soldering iron, 96
Z
Zener diode, 134
zinc electrode, 33

Colophon
The heading and cover font are BentonSans, the text font is Myriad Pro, and
the code font is TheSansMonoCondensed.
About the Author
Charles Platt became interested in computers when he acquired an Ohio
Scientific C4P in 1979. After writing and selling software by mail order, he
taught classes in BASIC programming, MS-DOS, and subsequently Adobe
Illustrator and Photoshop. He wrote five computer books during the 1980s.
He has also written science-fiction novels such as The Silicon Man (published
originally by Bantam and later by Wired Books) and Protektor (from Avon
Books). He stopped writing science fiction when he started contributing to
Wired in 1993, and became one of its three senior writers a couple of years later.
Charles began contributing to MAKE magazine in its third issue and is cur-
rently a contributing editor. Make: Electronics is his first title for Make Books.
Currently he is designing and building prototypes of medical equipment in his
workshop in the northern Arizona wilderness.

Make electronics learning_by_dis

More Related Content

What's hot (17)

Similar to Make electronics learning_by_dis (20)

Recently uploaded (20)

Make electronics learning_by_dis