Matlab simulink based digital protection of transformer

IJRET: International Journal of Research in Engineering and Technology eISSN: 2319-1163 | pISSN: 2321-7308
_______________________________________________________________________________________
Volume: 03 Issue: 02 | Feb-2014, Available @ http://www.ijret.org 484
MATLAB SIMULINK BASED DIGITAL PROTECTION OF
TRANSFORMER
P.B.Thote1
, M.B. Daigavane2
, N.G. Bawane3
1
Research Scholar, G.H.R.C.E, Nagpur (RTMNU, Nagpur), India
2
Principal, V.I.T, Nagpur (RTMNU, Nagpur), India
3
Principal, S.B.J.I.T.M.R, Nagpur (RTMNU, Nagpur), India
Abstract
Power transformer is one of the most important equipment in a power transmission and distribution system. This paper presents a
technology to simulate differential relay in Matlab Simulink based environment for determining its behavior during various operating
conditions. The results show that this simulation method can work properly and this will allow rapid modeling and testing of new
algorithm in view to improve protection of transformer.
Keywords: differntial protection, magnetising inrush current, internal faults, over fluxing,trip signal
-----------------------------------------------------------------------***----------------------------------------------------------------------
1. INTRODUCTION
Transformer is a vital and expensive component of electrical
power system. The unplanned outage of a power transformer is
costly for utilities and hence need adequate protection [1]. It is
necessary to study the various operating conditions of
transformer to explore new protection algorithm [2].The aim of
this paper is to simulate various conditions of a transformer like
load condition, internal faults, abnormal conditions like
magnetizing inrush current, over fluxing, etc. In this paper, the
physical model of a two winding 230 V/230 V is simulated in
MATLAB-SIMULINK. The block parameters of transformer
are obtained using experiment conducted on laboratory
transformer. All the mentioned operating conditions are applied
in this model one by one and are analyzed from differential
protection point of view. An example presented in this paper
demonstrates the capabilities and underline the advantages of
Matlab-Simulink environment to study differential current
pattern for various conditions which can be subsequently used
for designing suitable digital relay. This data can be used to
improve transformer protection using intelligent techniques.
2. DEVELOPMENT OF DIGITAL DIFFERENTIAL
RELAY
2.1 Main Simulink Model
The main simulink model used for obtaining differential current
data is shown in Figure 1
Fig 1 Simulink model for differential protection of Transformer
2.2 Results of Laboratory Experiment
To obtain the block parameters of transformer, open circuit and
short circuit test is performed. Figure 2 shows the experimental
set-up to obtain block parameters of transformer.

_______________________________________________________________________________________
Fig2. Experimental set-up
Figure 3 shows data entry window for two winding transformer.
Fig3. Data entry window for two winding Transformer
2.3 Validation of Simulink Model
For load of P= 1000 W and Q= 800 VAr, S= 1280.62 VA,
I1=I2 =5.56 A and I1peak =I2peak = 7.87 A
The waveforms obtained by this simulink model are in line with
the actual calculations as shown in figure 4.
Fig 4 Winding currents on two sides of a Transformer
This confirms the correctness of the simulink model and hence
data of differential current for various operating conditions
obtained from this model can be used for further analysis. The
pickup value of differential current is set equal to 0.35 A.
2.4 Subsystems used in Main Simulink Model
Figure 5 illustrates the components of subsystem 1 used in main
simulink model where differential current is input and Trip
signal is the output.
Fig 5 Sub-system 1 used in main simulink model
Figure 6 shows the components of subsystem 2.
Fig 6 Sub-system 2 used in main simulink model

_______________________________________________________________________________________
The relational operator determines whether the differential
current is more than the peak up value of current. Fundamental
and second harmonic block calculates the fundamental and
second harmonic contents of differential current. Divide block
calculates the ratio of second harmonic to fundamental
component. Relational operator 1 block determines whether the
ratio is more than the set limit of ratio. Not block and And
block realizes harmonic restrain scheme.
3. RESULTS AND DISCUSSION
The results are given for following conditions of energisation
and faults.
3.1 Normal Operation
When the transformer is operating normally, the differential
current is well below the peak up value and the relay does not
issue any trip signal as shown in Figure 7.It is the correct
operation of relay.
Fig 7 Differential current and Trip signal for normal condition
3.2 Internal Fault
When few turns of the windings are shorted, the differential
current exceeds the peak up value and the relay issues trip
signal as shown in figure 8.It is again the correct operation of
ralay.Various internal faults on winding 1 and 2 of transformer
are simulated by changing number of turns. The fault occurs at
0.02sec.
Fig 8 Differential current and Trip signal for internal fault
condition
In this case, the differential current is more than pick-up value
and relay will operate. It is the correct operation of relay.
3.3 Magnetizing Inrush Current
The transient magnetizing current of a transformer flowing after
connecting the transformer with AC source is called inrush
current. Inrush current is highly asymmetric. It results from
saturation of core of transformer caused by excessive growth of
magnetic flux in one direction only. The first peak of an inrush
current may exceed many times the value of transformer
nominal current. Fig.9 shows the waveform of a magnetizing
inrush current with transformer energized at instant zero on the
input voltage wave.
Fig 9 Magnetizing inrush current
It is possible to analyze the various factors which affect the first
peak of the inrush current like saturation characteristics of the
core, instant on input voltage wave where transformer is
energized, residual magnetic flux, etc in the simulation
presented in this paper.
Since the differential current is above the pickup value of
current, the relay issues trip signal as shown in fig 10.
Fig 10 Differential current and Trip signal for Magnetizing
inrush condition

_______________________________________________________________________________________
During this condition the relay mal-operates. Conventionally,
second harmonic blocking scheme is used for discrimination
between inrush current and fault current. But today’s new low
loss core material decreases the second harmonic component of
inrush current [3]. Therefore, researchers are using new
techniques like wave shape recognition, Digital Signal
Processing based techniques for accurate and rapid
discrimination between abnormal and fault conditions [4, 5].
For the past few years, inrush current became an interesting
topic and many researchers have focused their studies in this
matter [6].
3.4 Over Fluxing Condition
Increase in input voltage causes increase in working flux level.
The reduction in supply frequency also increases the core flux.
The generator transformers are more prone for over fluxing as
this may be subjected to an uncomfortable combination of over
voltage and under frequency during start-up. The ratio of V/f is
an index of over fluxing. Fig.11 shows differential current data
for the over fluxing condition when input voltage = 282 V and
input frequency = 47Hz which results in mal operation of relay.
Fig 11 Differential current and Trip signal for overfluxing
condition
CONCLUSIONS
The results presented in this paper are in line agreement with
the theoretical calculations. From the work presented in this
paper, it is possible to obtain differential current data for
various operating conditions which can be used for improving
the protection function of transformer, mainly to discriminate
between transformer internal faults and transients like inrush,
over fluxing conditions.
REFERENCES
[1] S.V.Kulkarni,S.A.Khaparde, Transformer Engineering.
Design and Practice, Marcel Dekker Inc., New York,
Basel, 2004.
[2] Haihui Song, Fangming Zhao, Di He, “Simulation study
on internal fault of Transformer ” Elsevier, sciverse
science direct, 2012 international conference on solid
state devices and material science, Physics Procedia 25
(2012) pp 459-464
[3] J.P Patra, “A discussion on power transformer
magnetizing inrush, remedy, fault detection in Matlab-
simulink environment”, International Journal of
Electrical Engineering, ISSN 0974-2158 vol.4, number 1
(2011), pp 83-102
[4] R. Bouderbala, H. Bentarzi and A. Ouadi, “Digital
Differential Relay Reliability Enhancement of Power
Transformer”, International Journal of Circuits, System
And Signal Processing
[5] M.S. El-Bages, “Improvement of Digital Differential
Relay Sensitivity For Internal Ground Faults In
Powertransformers ”, IJPTE Journal, ISSN 2077-3528,
pp 1-5
[6] P.L,Mao and R.K.Aggarwal, "A wavelet transform
based decision making logic method for discrimination
between internal faults and inrush currents in power
transformers", International journal of Electric power
and Energy systems, Vol. 22, no 6 ,pp-389-395 2000
[7] A.I.Megahed, A.Ramadan, W.El.Mahdy, "Power
transformer differential relay using wavelet transform
energies", in:Power and Energy Society General
Meeting, IEEE, 20-24,1-6,2008
REFERENCES:
Pankaj B. Thote has born in Nagpur
(Maharashtra)in 1975. He received the
B.E. degree in Electrical Engineering in
1997 and M.E. degree in Electrical Power
System in 2010 from Sant Gadge Baba
Amravati University, India. He is
currently working as a Assistant Professor
& Head in Electrical Engineering
Department of Shri Shantilalji Badjate Institute of Technology,
Managment and Research, Nagpur. His research interests
include network analysis and protection. He is a Life Member
of the Indian Society for technical Education. He is pursuing his
Ph.D degree from Rashtrasanth Tukdoji Maharaj Nagpur
University.
Dr. Manoj B. Daigavane obtained the
B.E. Degree in Power Electronics
Engineering from Nagpur University,
India in 1988. He received the M.S.
Degree in Electronics and Control
Engineering from Birla Institute of
Technology and Science, Pilani (Raj) India in 1994. He also
obtained the M.E. Degree in Power Electronics Engineering
from Rajeev Gandhi University of Technology, Bhopal (M.P),
India in 2001. He received Ph D Degree in Electrical
Engineering from R.T.M. Nagpur University, India in 2009.
Since Sept.1988- June 2007, he had been with the Department
of Electronics and Power Electronics Engineering, B. D.
College of Engineering, Sewagram (Wardha), affiliated to the

_______________________________________________________________________________________
Nagpur University, India. Since July 1, 2007 to Apr 30, 2009,
he was Professor & Head of Electrical and Electronics
Engineering, Disha Institute of Mgmt. and Tech., Raipur (C.G.)
where he is engaged in teaching & research. Earlier, he was
Principal at S. D. College of Engineering, Wardha. Presently,
he is Principal of V.I.T College of Engineering, Nagpur –
Maharashtra (India). His main areas of interest are resonant
converters, Power quality issues, DSP applications and Power
electronics for motor drives. He has been responsible for the
development of Electrical Machines and Power Electronics
Laboratories He is a Member of the Institution of Engineers
(India) and a Life Member of the Indian Society for technical
Education.
Dr. Narendra G. Bawane is a Professor
& Principal of S. B. Jain Institute of
Technology, Management & Research,
Nagpur. Prior to this assignment, he was
Head of Computer Science and
Engineering department at G. H. Raisoni
college of Engineering, Nagpur. He has
also worked with B.D. College of
engineering sewagram and Govt.
Polytechnic, Nagpur for several years. He is having total
teaching experience of more than 24 years to his credit. He has
completed his B.E. from Nagpur University in 1987 and M.
Tech. in 1992 from IIT, New Delhi. He completed his Ph. D. in
2006 at VNIT, Nagpur. His areas of interest are
ANN,Fuzzy,Embeded Systems etc.

Matlab simulink based digital protection of transformer

More Related Content

What's hot (18)

Similar to Matlab simulink based digital protection of transformer (20)

More from eSAT Journals (20)

Recently uploaded (20)

Matlab simulink based digital protection of transformer