PERFORMANCE EVALUATION OF RIP AND OSPF IN IPV6 USING OPNET 14.5 SIMULATOR

International Journal of Technical Research and Applications e-ISSN: 2320-8163,
www.ijtra.com Volume 2, Issue 6 (Nov-Dec 2014), PP. 37-41
37 | P a g e
PERFORMANCE EVALUATION OF RIP AND
OSPF IN IPV6 USING OPNET 14.5 SIMULATOR
Rajneesh Narula1, Pallavi Aggarwal2
Computer Science and Engineering
Adesh Institute of Engineering and Technology
Faridkot, India
1
raj_narula74@yahoo.com, 2
aggarwal_pallavi@ymail.com
Abstract— In this modern internet era, routing protocol
plays an important role. They forward the packets form source
to destination. There are many routing protocols are used. In
this paper, we evaluated the performance of different routing
protocol like RIP and OSPF for IPv6. OPNET simulation tool
14.5 is used to evaluate the performance of RIP and OSPF in
three network models in which two network models will
perform on one routing protocol only while the third are used to
evaluate the performance of these routing protocol are packet
delay variation, end to end delay, traffic received, traffic sent,
response time, jitter, page response time, object response time,
traffic dropped for IPv6 Etc. we designed three scenarios to
compare their performance.
Keywords: RIP, OSPF, OPNET14.5, Performance analysis,
IPv6.
I. INTRODUCTION
Routing refers to the process of determining the best route
for the transmission of data packets from source to
destination and it is based upon routing protocols. Routing
protocols are a set of rules in which communication network
follows when computers try to communicate with each other
across networks and communication between two routing
protocols is dependent upon the routing algorithm which is
purely dependent upon the metrics to find the path to transfer
the data across two networks [1]. Routing protocols utilize a
routing table to store the results of these metrics. There are
two types of routing protocols: interior gateway protocol
(IGP) and exterior gateway protocol (EGP). RIP, OSPF,
EIGRP are most commonly used IGPs and a typical EGP is
BGP (Border Gateway Protocol) [2]. Now a day’s many
routing protocol exist, among these routing protocol most
famous are RIP (Routing Information Protocol) and OSPF
(Open Shortest Path First). Both are the examples of interior
gateway routing protocol. RIP is a distance vector dynamic
routing protocol that uses hop count as its routing metrics.
OSPF is a link state routing protocol that uses cost and
bandwidth as its routing metrics. In this type of routing
protocol, each router works independently to calculate its
own shorter route towards the destination [1].IPv6 (internet
protocol version6) is a new addressing protocol developed in
1999 designed to remove the shortcoming of IPv4. IPv4
(internet protocol version 4) was developed in 1981; did not
get any major change afterward and also it provides only 32
bit addressing space containing 4.3 billion unique internet
protocol addresses. Each internet enabled device requires a
unique IP address from this address space. But the rapid
growth of the internet has resulted in these addresses being
exhausted. IPv6 has 128 bits address space which is four
times more than IPv4. Moreover, IPv6 brings a number of
improvements over IPv4 to increase addressing space. IPv4
must have IPSec security, making it more secure than IPv4
[3]. In this paper, we analysis the performance of RIP and
OSPF routing protocol on IPv6 and also compared and
analyzed simulation results in terms of Database Query
response time, page response time and object response time
in HTTP, IPv6 Traffic dropped, jitter, end to end delay,
traffic received and traffic sent in Voice, packet delay
variation, end to end delay, traffic received and traffic sent in
Video Conferencing.
II. RELATED WORK
Loan Fitigau and Gavril Toderean [4], network
performance evaluation for RIP, OSPF and EIGRP routing
protocols in OPNET simulator and using various simulation
scenarios to compare their performance. Mohamad A.
Yehia,Mohammed S. Aziz,Hussein A. Elsayed [5], presents a
comparative analysis of routing protocol EIGRP,OSPF and
RIP for real time applications. Don Xu and Ljilijana
Trajkovic [2], comparing the performance of routing protocol
such as RIP, EIGRP and OSPF using OPNET modeler using
various parameters like network convergence, Ethernet delay,
email upload response time etc. Sajad Farhangi and Saeed
Golmohammadi [6], describes the evaluation of IS-IS and
IGRP on performance parameters such as convergence
duration, throughout, packet delay variation, packet end to
end delay and traffic sent. Alex Hinds, Anthony Atojoko and
Shao Yin`g Zhu [3], studied the routing protocols OSPF and
EIGRP showing the differences between IPv4 and IPv6.
IKram Ud Din and Saeed Mahfooz [7], performance analysis
of routing protocols RIP, OSPF, IGRP and EIGRP for the
parameters such as packets dropping, traffic received, end to
end delay and jitter in voice. V.Vetriselvan, Pravin R. Patil
and M.Mahendran [8], survey the performance evaluation of
various routing protocol such as RIP, OSPF and EIGRP with
certain criteria such as jitter, convergence time, end –to-end
delay., throughput, queuing delay, link utilization. Saubhagya
Das, Santosh Subedi and N. Shekar V. Shet [9], network
performance analysis of dynamic routing protocols for real
time applications such as Delay, FTP, E-mail, HTTP, VoIP
and Video Conferencing through the simulated network
models.
III. PROTOCOL CONCEPTS
A. RIP (Routing Information Protocol)
RIP is a distance vector dynamic routing protocol that uses
the hop count as its routing metrics. RIP prevents routing
loops by implementing a limit on the number of hops allowed
in a path from source to destination. The maximum number
of hops allowed for RIP is 15. This hop limit also limits the
size of networks that RIP can support. A hop count of 16 is
considered an infinite distance, in other words the route is
considered unreachable. RIP implements the split horizon,
route poisoning and hold down mechanisms to prevent
incorrect routing information from being propagated [10].
RIP only maintains the routing table of the best path in the
network for every destination. There are three versions of
Routing Information Protocol: RIPv1, RIPv2and RIPNG.

38 | P a g e
RIPv1 is a Classful routing protocol but RIPv2 is a Classless
routing protocol. RIPNG is an extension of RIPv2 and also
supports IPv6 networking.
B. OSPF (Open Shortest Path First)
OSPF was designed with the specific goal of handling
routing tasks within an enterprise network; this requires quick
convergence, minimum routing traffic, and better security.
OSPF is a link state protocol and also maintains the routing
table for all connections in the network. The concept of OSPF
routing is based on creating, maintaining and distributing a
link –state database, which describes a collection of routers
and their operational interfaces, how they are interconnected
and cost to use the interfaces. Cost is a metrics used to
describe the relative efficiency of various routes to the
destination. Each router in the routing domain is responsible
for the creation of its local piece of topology by link state
advertisements (LSA). LSAs contain information describing
routers, networks, reachable routes, route prefixes and
metrics. The LSAs are then reliably distributed to all other
routers in a process called flooding, which allows OSPF
routers to synchronize their topology databases. Most of the
OSPF operations are dedicated to keeping the link-state
database synchronized among OSPF routers. As long as
every OSPF router has an identical link state database, every
router can calculate the shortest paths to the advertised
destination, using Dijkstra Shortest Path First algorithm [11].
IV. SIMULATION NETWORK TOPOLOGY
In this paper, we used OPNET 14.5 Simulator. OPNET is
a high level simulation tool that has been used in many high
level researches. It enables simulation of heterogonous
networks by employing a various protocols [12]. In real, we
cannot create such a network; it is possible only simulation
because simulation provides us mathematical and graphical
form of result and we can easily understand these results. In
the network, we have 11 routers that are Cisco 7000 series
and all the routers are connected together with point to point
(PPP) using Digital Signal 3 (DS3) link model and also we
have used four LANs that is Ethernet LANs and four
workstations that is Cisco WS-C3560 series and four
Ethernet Server .All the workstations are connected with one
router, one LAN and one server with 100BaseT link models.
LAN is used to configure different application such as HTTP,
database query, voice conferencing and voice. LAN1 is for
video conferencing, LAN2 is for voice, LAN3 is for database
query and LAN4 is for HTTP. We have one application
definition and profile definition. The profile definition is used
to create users profiles to be specified in different nodes in
the network [5]. We have four profiles that are HTTP, voice,
video conferencing and database query. All the profiles are
configured with operation mode set to simultaneous and
number of repetitions is constant (0). We are used to
application definition to define parameters for video
conferencing application such as Frame Interarrival time =15
frames/sec, Frame Size Information (bytes) =128*240 pixel,
Type of Services=best effort (0), Symbolic Destination
Name=video destination.For voice application such as
encoder scheme is G.729 A (silence), Type of Service (TOS)
is best effort (0), voice frames per packet is 1and
compression and decompression delay is 0.02 second. For
HTTP such as Page Interarrival time =exponential (10) in
seconds. In page properties, we have two rows -object size
first is constant (1000) and second is medium image and
number of objects (objects per page) is constant (1) and
constant (2). And in server selection, initial repeat probability
is search and page per server is exponential (2). For database
query, Transaction Interarrival time (seconds) =exponential
(12), Transaction Size (bytes) =constant(32768) and Type of
Service= best effort(0).
Table 1: Applications Description
Voice IT Telephony and Silence
Suppressed
Voice Conferencing High Resolution
HTTP Searching
Database Query High Load
Fig 1: Network Model
V. SIMUATION RESULTS
Our simulation involves three scenarios for the network
topology. The simulation time is set to 600 seconds for
RIPNG, OSPFv3 and OSPFv3_RIPng scenarios.
A. Packet delay variation:
This parameter is defined as a delay in receiving packets
at the receiver. On the transmitter side, data packets are sent
continuously in the channel. Due to networks congestion,
improper queuing, or configuration errors, the packet may
not receive, in the order that the transmitter and receiver with
the same period were sent. In real-time applications such as
video conferencing packets delay cannot be ignored due to
the Packet delay variation, which causes packet loss and also
there will be no recovery of video. Packet delay variation for
voice conferencing traffic is ilustracted in figure 3.
According to the figure, OSPFv3_RIPNG has lower value
than other scanarios and so OSPFv3_RIPNG shows better
performance.
Fig 2: Video Conferencing Packet Delay Variation

39 | P a g e
B. End to End Delay
When the packets transmitted by a network from source
to destination then end to end delay time has been
considered. When it takes too much time to arrive the
packets to the receiver, it causing delays in the whole process
and therefore has a critical effect on the performance of a
communication network. Network with large values of end
to end delay, the packet can be efficiently destroyed. Packet
losses due to large end to end delay will have impact on the
quality of both audio and video traffic on the receiver. The
end to end delay for video conferencing in figure 3, OSPFv3
has minimum end to end delay compared with other
scenarios. So OSPFv3 performs well.
Fig 3: Packet End To End Delay In Video Conferencing
In voice, OSPFv3_RIPNG has minimum end to end
delay compared with other scenarios.
Fig 4: Packet End To End Delay In Voice
C. Traffic Received
Voice/Video traffic is the total number of audio and video
packets received during video conferencing or other type of
real time communication. In video conferencing, OSPFv3
receives less traffic than other scenarios.
Fig 5: Traffic received in video conferencing
In voice, OSPFv3_RIPNG receives less traffic than OSPFv3
and RIPNG. So OSPFv3_RIPNG performance is better than
other scenarios.
Fig 6: Traffic Received in Voice
D. Traffic Sent
Voice/ Video traffic is the total number of audio and
video packets sent during video conferencing or other type of
real time communication. In fig 7, OSPFv3 sends less traffic
and OSPFv3_RIPNG send more traffic. So the performance
of OSPFv3 is better than other scenarios.

40 | P a g e
Fig 7: Traffic Sent in Video Conferencing
In voice fig 8, OSPFv3_RIPNG sends less traffic and
RIPNG has more. So OSPFv3_RIPNG performance is better
than other scenarios.
Fig 8: Traffic Sent in Voice
E. Jitter in voice
Jitter is defined as variation in delay times of received
packets. At sending sides, packets are sent in a continuous
stream in a equally spaced time slots. The rate is much lower
than average rate, resulting from traffic congestion and for
improving performance of a voice network this factor should
be as small as possible. In fig. 9, combination of
OSPFv3_RIPNG has the lowest jitter than OSPFv3 and
RIPNG.
Fig 9: Jitter in Voice
F. Traffic dropped in IPv6
When a router or switch is unable to receive incoming data
packets at a given time, is called packet loss/ drop. In fig 10,
RIPNG has the least number of packets dropped as compared
to another scenario. So RIPNG performance is better.
Fig 10: Traffic Dropped in IPv6
G. Page response time in HTTP
OSPFv3_RIPNG takes less time than RIPNG and
OSPFv3. So OSPFv3_RIPNG performs well.
Fig 11: Page Response time in HTTP

41 | P a g e
H. Object response Time in HTTP
In object response time, the OSPFv3_RIPNG takes less
time than RIPNG and OSPFv3. So OSPFv3_RIPNG
performance is better than others scenarios.
Fig 12: Object Response Time in HTTP
I. Response time in Database Query
Time elapsed between sending a request and receiving the
response packet for the database query application in this
node. Measured from the time a client application sends a
request to the server to the time it receives a response packet.
In fig 13, the response time of OSPFv3 is better than other
scenarios.
Fig 13: Response Time in Database Query
VI. CONCLUSION
RIP and OSPF are Interior Gateway Routing Protocols
widely used in computer networking. In this paper, we have
presented a comparative analysis of selected routing
protocols such as RIP and OSPF in IPv6. The comparative
analysis has been done in the same network with different
protocols for real time applications. Performance has been
measured on the basis of the parameters that aimed to figure
out the effect of routing protocols.
In the implementation, Packet Delay Variation in Video
Conferencing, Jitter, End to End Delay, Traffic Received, and
Traffic Sent in voice and Object Response Time and Page
response Time in HTTP performs better in OSPFv3_RIPNG
(combination of RIPNG and OSPFv3) than RIPNG and
OSPFv3.
Another Performance Metrics for real time applications is
End to End Delay, Traffic Received and Traffic sent in Video
Conferencing, Response time in Database Query performs
better in OSPFv3 than OSPFv3_RIPNG and RIPNG.
Traffic Dropped in IPv6 parameter performs better in RIPNG
than OSPFv3 and OSPFv3_RIPNG in IPv6.
In this work, the comparative performance among RIP,
OSPF and combination of RIP and OSPF routing protocols in
IPv6 for real time applications has been analyzed. By
comparing these protocols performance, we have come
across that the combined implementation of RIPNG and
OSPFv3 routing protocol in the network in IPv6 performs
better than RIPNG and OSPFv3. In the case of individual
routing protocol performance, overall performance of
OSPFv3 is better than RIPNG.
REFERENCES
[1] Jagdeep Singh and Dr. Rajiv Mahajan,"Simulation Based
Comparative Study Of RIP, OSPF and EIGRP", International
Journal of Advanced Research in Computer Science and
Software Engineering, Volume 3, Issue 8, August 2013.
[2] Don Xu and Ljiljana Trajkovic, "Performance Analysis of RIP,
EIGRP and OSPF using OPNET", vancouver, British
Columbia, Canada.
[3] Alex Hinds, Anthony Atojoko and Shao Ying Zhu, "Evaluation
of OSPF and EIGRP Routing Prorocol for IPV6 ", International
Journal of Future Computer and Communication, Vol.2, 4
August 2013.
[4] Loan fitigau and Gavril Toderean, "Network Performance
Evaluation for RIP, OSPF and EIGRP Routing Protocols",
IEEE 2013.
[5] Mohamad A. Yehja, Mohammed S. Aziz, Hussein A. Elsayed,"
Analysis of IGP Routing Protocols for Real Time Applications:
A Comparative Study ", International Journal of Computer
Application (0975-8887), Volume 26-No. 3, July 2011.
[6] Sajad Farhangi and Saeed Golmohammadi, “A comparative
study of IS-IS and IGRP protocols for Real time applications
based on OPNET”, Advances in Electrical Engineering
Systems, Vol. 1, No. 1, March 2012, pages 65-70.
[7] IKram Ud Din, Saeed Mahfooz and Muhammad Adnan,
“Analysis of the routing protocols in the Real Time
Transmission: A Comparative study”, Global Journal of
Computer Science and Technology, Vol. 10, Issue 5, Ver. 1.0,
July 2010, pages 18-22.
[8] V.Vetriselvan, Pravin R. Patil, M.Mahendran,"Survey on the
RIP, OSPF, EIGRP Routing Protocol",(IJCSIT) international
journal of computer science and information technologies,Vol.
5(2),2014,1058-1065.
[9] Saubhagya Das, Santosh Subedi and N. Shekar V. Shet, “
Network Performance Anaysis of Dynamic Routing protocols
real time applications”, International Journal of Modern
Engineering Research,Vol.4, Issue 5, May 2014, pp. 49-57.
[10] http://www.cisco.com/c/en/ US/ td/docs/ios/
[11] www.ixiacom.com/pdfs/library/white_papers/ospf.pdf
[12] Shah. A and Waqas J. Rana, "Performance Analysis of RIP and
OSPF in Network Using OPNET", IJCSI International Journal
of Computer Science Issues, Vol. 10, Issue 6, No.2, Novermber
2013.

PERFORMANCE EVALUATION OF RIP AND OSPF IN IPV6 USING OPNET 14.5 SIMULATOR

More Related Content

What's hot (20)

Viewers also liked (20)

Similar to PERFORMANCE EVALUATION OF RIP AND OSPF IN IPV6 USING OPNET 14.5 SIMULATOR (20)

More from International Journal of Technical Research & Application (20)

Recently uploaded (20)

PERFORMANCE EVALUATION OF RIP AND OSPF IN IPV6 USING OPNET 14.5 SIMULATOR