Power system state estimation using teaching learning-based optimization algorithm

TELKOMNIKA Telecommunication, Computing, Electronics and Control
Vol. 18, No. 4, August 2020, pp. 2125~2131
ISSN: 1693-6930, accredited First Grade by Kemenristekdikti, Decree No: 21/E/KPT/2018
DOI: 10.12928/TELKOMNIKA.v18i4.14159  2125
Journal homepage: http://journal.uad.ac.id/index.php/TELKOMNIKA
Power system state estimation using teaching learning-based
optimization algorithm
Surender Reddy Salkuti
Department of Railroad and Electrical Engineering, Woosong University, Republic of Korea
Article Info ABSTRACT
Article history:
Received Sep 20, 2019
Revised Mar 22, 2020
Accepted Apr 7, 2020
The main goal of this paper is to formulate power system state estimation
(SE) problem as a constrained nonlinear programming problem with various
constraints and boundary limits on the state variables. SE forms the heart of
entire real time control of any power system. In real time environment,
the state estimator consists of various modules like observability analysis,
network topology processing, SE and bad data processing. The SE problem
formulated in this work is solved using teaching leaning-based
optimization (TLBO) technique. Difference between the proposed TLBO and
the conventional optimization algorithms is that TLBO gives global optimum
solution for the present problem. To show the suitability of TLBO for solving
SE problem, IEEE 14 bus test system has been selected in this work.
The results obtained with TLBO are also compared with conventional
weighted least square (WLS) technique and evolutionary based particle
swarm optimization (PSO) technique.
Keywords:
Meta-heuristic algorithms
Nonlinear programming
Observability
Power flow analysis
State estimation
This is an open access article under the CC BY-SA license.
Corresponding Author:
Surender Reddy Salkuti,
Department of Railroad and Electrical Engineering,
Woosong University,
17-2, Woosong University, Jayang-dong, Dong-gu, Daejeon-34606, Republic of Korea.
Email: surender@wsu.ac.kr
1. INTRODUCTION
In recent years, several electrical utilities around the globe are developng different knowledge-based
applications to inrgrate in the operation of control centers. These methods must be capable of meeting all
the important tasks of efficient control system such as numerical stability, computation efficiency, and
implementation complexity. Load dispatcher in power system control centre is required to know at all times the
value of voltages, currents and power throughout the network. Some of the values such as bus voltage
magnitude and power line flows can be measured within a certain degree of variance [1]. Difficulties are further
encountered when some of the data is missing either due to meter being out of order or missing transmission.
State estimation (SE) is considered as the process of assigning values to unknown system state
variables, based on the measurements obtained from that system. It utilizes the available redundancy, for
systematic cross checking of the measurements, to approximate the states as well as generate information in
respect of missing observations or gross measurement errors called bad data. The prerequisite for state
estimation is that system must be observable with available measurements. States of a power system can also
be computed with the load flow calculations, based on equal number of measurements, assuming them to be
accurate [2]. However, the implicit error will lead to imperfect data base and prejudice the security

 ISSN: 1693-6930
TELKOMNIKA Telecommun Comput El Control, Vol. 18, No. 4, August 2020: 2125 - 2131
2126
monitoring. Whereas, the state estimator is considered as a data processing technique for use on a digital
computer to transform measurement vector into an estimate of system’s states, which is not only accurate but
best reliable also. As the state estimator is required to cater for the needs of online application, computation
speed plays a vital role especially when systems are large. Alternate methods of SE are being reported to
optimize on computational efficiency, numerical stability, and complexity in implementation [3].
A hybrid algorithm for solving the SE problem by using weighted least square, weighted least
absolute value and particle swarm optimization (PSO) methods is presented in [4]. In [5] uses unscented
Kalman filter and extended Kalman filter to estimate power system states by a phasor measurement unit
(PMU). A comparative analysis of SE in rectangular and polar coordinates has been proposed in [6]. A SE
approach for a distribution system considering the condition variables, i.e., node voltage and angle of feeder
is proposed in [7]. In [8] presents approach for the implementation of reactive power and/or active power
measurements in the SE. An agent-based approach for dynamic SE of power system by taking the advantages
of hybrid measurement data is presented in [9]. A hybrid SE method with genetic algorithm and cellular
computational network is proposed in [10] to overcome the dimensionality problem of SE.
The application of PSO for solving SE problem within a power system is proposed in [11].
A non-iterative method which has no issues with convergence and doesn't need starting guess is used in [12]
for solving the SE problem. A robust and reliable least winsorized square estimator for static SE is proposed
in [13]. In [14] proposes an extended Kalman filter based dynamic SE by using PMU data. A SE method
including equality constraints to model zero injections and voltage dependent loads is proposed in [15].
A methodology by including the uncertainty in SE is proposed in [16]. An overview of power system SE
control by load flow program input data is presented in [17]. A SE approach by considering the measured
data obtained from synchronized and unsynchronized sensors is presented in [18].
This paper solves the SE problem of power system as a constrained nonlinear programming problem
with various constraints and boundary limits on state variables. The objective of SE is to find best estimated
state variables for the considered power system by optimizing all the errors in measurements. This problem is
solved by enforcing the equality and limit constraints by using teaching-learning based optimization (TLBO)
technique. TLBO is formulated by considering two methods of learning (i.e., teacher and learner phases) in a
classroom. Teacher phase consists the interaction between learner and teacher, whereas learners phase consists
the interaction among the learners. This paper is presented as follows. The problem formulation of SE is
described in section 2. The solution algorithm, i.e., TLBO algorithm is presented in section 3. Results and
discussions on standard IEEE 14 bus system are presented in section 4. conclusions are presented in section 5.
2. PROBLEM FORMULATION
Load flow calculations indeed are an inevitable tool for off-line studies and planning exercises, but
incomplete and erroneous measurement is a real time proposition. Solution for such situation has been
provided by static state estimator, which ignores the slow changes in the system and utilizes redundant set of
measurements for cross checking and approximating the most reliable estimates of system state [19]. State
estimator should estimate the system states as quickly as possible, but conventional computer-based methods
are almost reaching a limit in terms of speed. Figure 1 depicts the description of state estimator/SE. In this
figure, m is number of measurements, n is number of state variables.
Measurement Uncertainties
State Estimator
m measurements
(m>n)
n State Variables
Network Parameters
Figure 1. Schematic diagram of state estimator
The state vector (x) has voltage magnitudes and angles at buses [20]. Power system with N number
of buses can be expressed as x=[δ, V]T
with size n=2N-1, includes (N-1) bus voltage angles (δi). General
static SE model is expressed by using [21],
𝑧 = ℎ(𝑥) + 𝜖 (1)

TELKOMNIKA Telecommun Comput El Control 
Power System state estimation using teaching learning-based optimization … (Surender Reddy Salkuti)
2127
where z is all measurements, and h(.) represents nonlinear measurement functions. Here, meta-heuristic based
optimization technique is used for solving nonlinear programming problem [22]. It is often desirable to put
different weightings on different components of measurements as some of the measurements may be more
reliable and accurate than the others and should be given more importance. In power network there are some
nodes with zero injections i.e., switching substations as constant load. Such buses are called constrained buses
and can be included in the cost function by assigning large weighting factors [23]. The estimate of x can be
obtained by minimizing the function of weighted least square (WLS), and it is expressed as [24],
𝐽(𝑥) = [𝑧 − ℎ(𝑥)] 𝑇
𝜔[𝑧 − ℎ(𝑥)] (2)
where 𝜔 is a diagonal matrix. The estimate is solved by an iterative method, which determines corrections
(Δx) by solving the following function [25],
𝐺(𝑥)∆𝑥 = 𝐻(𝑥) 𝑇
𝜔∆𝑧 (3)
where Δz = z-h(x), and H(x)=
𝜕ℎ(𝑥)
𝜕𝑥
=Jacobian matrix.
𝐺(𝑥) = 𝐻(𝑥) 𝑇
𝜔𝐻(𝑥) (4)
where x=xk
at the kth
iteration. In view of fact that power systems nowadays are becoming more openly
accessible; maneuverability of their power flow continues to be a general concern in the coming decade [26].
2.1. SE: objective function
The objective of SE is to minimize the weighted squared error between calculated and measured
quantities. Where 𝑅−1
is the weights of individual measurements, and it is solved subject to following
inequality and equality constraints and it is expressed as,
𝑚𝑖𝑛𝑖𝑚𝑖𝑧𝑒
1
2
[𝑧 − ℎ(𝑥)] 𝑇
𝑅−1[𝑧 − ℎ(𝑥)] (5)
2.2. Equality constraints
These are the active and reactive power balance equations at all buses, which can be expressed as [27],
𝑃𝑖 = ∑ 𝑉𝑖 𝑉𝑚(𝐺𝑖𝑚 𝑐𝑜𝑠𝛿𝑖𝑚 + 𝐵𝑖𝑚 𝑠𝑖𝑛𝛿𝑖𝑚) = 0𝑁
𝑚=1 (6)
𝑄𝑖 = ∑ 𝑉𝑖 𝑉𝑚(𝐺𝑖𝑚 𝑠𝑖𝑛𝛿𝑖𝑚 − 𝐵𝑖𝑚 𝑐𝑜𝑠𝛿𝑖𝑚) = 0𝑁
𝑚=1 (7)
2.3. Inequality constraints
2.3.1. Voltage constraints
They include minimum and maximum limits on bus voltage magnitudes, and they are expressed as,
𝑉𝑖
𝑚𝑖𝑛
≤ 𝑉𝑖 ≤ 𝑉𝑖
𝑚𝑎𝑥
(8)
2.3.2. Phase angle constraints
At each bus, the phase angle must be between minimum and maximum limits, and they are
expressed as,
𝛿𝑖
𝑚𝑖𝑛
≤ 𝛿𝑖 ≤ 𝛿𝑖
𝑚𝑎𝑥
(9)
2.3.3. Line flow constraints
This constraint can be expressed as [28],
𝑃𝑙𝑖
𝑚𝑎𝑥
≥ 𝑃𝑙𝑖 (10)
2.3.4. Generator reactive power constrsint
The reactive power limits of generator are expressed as,
𝑄 𝐺𝑖
𝑚𝑖𝑛
≤ 𝑄 𝐺𝑖 ≤ 𝑄 𝐺𝑖
𝑚𝑎𝑥
(11)

 ISSN: 1693-6930
2128
3. TLBO ALGORITHM
The SE problem proposed in this paper is solved by using TLBO. It is a population based
meta-heuristic technique developed to get global solution. TLBO takes the advantage of two approaches of
learning in a classroom. First method is through the interaction between the learner and the teacher, and this
is termed as teacher phase. The second one is through the interaction among learners, and this is termed as
learner phase [29]. The flowchart of TLBO is depicted in Figure 2. The reader may refer references [29, 30]
for more details of TLBO algorithm.
Initialize number of students
(population) and termination criterion
Estimate the mean of each design variable
Selects the best solution (teacher)
Change the solution based on best solution
χnew = χold + r (χteacher – (Tf )Mean)
Choose any two solutions randomly χi and χj
Optimum objective function values
Is χi better than χj?
Is new solution better
than existing?
Is the new solution
better than existing?
Reject
Accept
Accept
Is termination
criteria sattisfied?
χnew = χold + r (χi – χj)
χnew = χold + r (χj – χi)
No Yes
StudentPhaseTeacherPhase
Yes No
Reject
No Yes
Yes
No
Figure 2. Flow chart of TLBO algorithm
4. SIMULATION RESULT AND DISCUSSION
In this work, standard IEEE 14 bus [31] system is considered for solving the proposed SE problem.
For this problem, the voltage magnitudes at each bus and the phase angles at all buses except reference bus
are selected as the state variables. Load flow solution is used for obtaining the true values, and measurements
were made by adding errors to the true values. Zero power injection at nodes with no generation and no
load are considered as equality constraints. Proposed SE problem is solved by using TLBO algorithm.
The data required for solving the SE problem on standard IEEE 14 bus system is taken from [31].
The measurement set data of IEEE 14 bus system is depicted in Figure 3 and in Table 1. The bus numbers 5
and 7 are considered as zero injection buses. In this test system, total 32 measurements are considered, in that
12 are considered as the bus injection type measurements and 20 are considered as the line flow type
measurements [32]. With this data, the SE problem is solved by using TLBO algorithm.
The estimated state variables by solving the SE with equality constraints are presented in Table 2.
Errors of estimate values (i.e., ∆P and ∆Q) obtained by solving the SE using TLBO are reported in Table 3.
The errors of estimated values obtained using the TLBO algorithm are also compared with WLS technique
and the evolutionary based PSO algorithm. From the obtained results, it is clear that by solving SE problem
by using teaching-learning based optimization (TLBO) has better results when compared to conventional
WLS technique and the evolutionary based PSO algorithm.

2129
~
~ ~
C
3
2
5
4
7
8
9
6
101112
1413
1
10
8
1
15
16
17
20
13
19
12
11
9
14
64
7
3
52
1
18
Line flow
zero injections
injection measurement
Figure 3. Measurement data set for IEEE 14 bus system
Table 1. Measurement data set for IEEE 14 bus system
Measurements Measurement Type Buses P (MW) Q (MW)
z1 Injection 1 224.62 -17.22
z2 Injection 2 18.23 25.35
z3 Injection 3 -94.53 4.26
z4 Injection 4 -47.83 7.04
z5 Injection 6 -11.29 3.44
z6 Injection 8 0.00 17.33
z7 Injection 9 -29.55 2.34
z8 Injection 10 -9.22 -6.35
z9 Injection 11 -3.27 -1.25
z10 Injection 12 -6.1 -1.6
z11 Injection 13 -13.66 -6.05
z12 Injection 14 -14.87 -4.89
z13 Line flow 1-2 151.96 -16.28
z14 Line flow 1-5 72.65 4.79
z15 Line flow 2-3 72.43 6.03
z16 Line flow 2-4 54.47 -1.23
z17 Line flow 2-5 39.26 0.99
z18 Line flow 3-4 -24.37 3.6
z19 Line flow 4-5 -63.84 13.9
z20 Line flow 4-7 28.06 -19.72
z21 Line flow 4-9 16.07 -5.79
z22 Line flow 5-6 44.4 -17.94
z23 Line flow 6-11 7.37 3.5
z24 Line flow 6-12 7.84 2.56
z25 Line flow 6-13 17.91 7.45
z26 Line flow 7-8 0.00 -16.88
z27 Line flow 7-9 28.05 7.14
z28 Line flow 9-10 5.21 4.28
z29 Line flow 9-14 9.36 3.48
z30 Line flow 10-11 -4.02 -2.1
z31 Line flow 12-13 1.66 0.8
z32 Line flow 13-14 5.68 1.77

 ISSN: 1693-6930
2130
Table 2. Estimated state variables after solving the SE for IEEE 14 bus system
Bus No. V δ Bus No. V δ Bus No. V δ
1 1.060 0 6 1.071 -12.68 11 1.058 -13.167
2 1.045 -4.731 7 1.062 -12.080 12 1.057 -13.296
3 1.010 -12.309 8 1.090 -11.922 13 1.051 -13.443
4 1.022 -9.615 9 1.055 -13.481 14 1.037 -14.258
5 1.024 -8.046 10 1.051 -13.553
Table 3. Errors of estimated values obtained by using WLS technique, PSO and AFSOA
Measurements
SE Using WLS SE Using PSO SE Using TLBO
∆P ∆Q ∆P ∆Q ∆P ∆Q
z1 0.0037 -0.0019 0.0052 -0.0034 0.0061 -0.0046
z2 -0.0018 -0.0061 0.0019 -0.0069 0.0042 -0.0066
z3 -0.0028 0.0028 0.0025 -0.0028 0.0018 -0.0025
z4 -0.0014 0.0024 -0.0009 0.0025 0.0017 0.0023
z5 -0.0016 -0.0022 -0.0015 -0.0034 -0.0017 -0.0051
z6 -0.0012 -0.0081 -0.0015 -0.0039 -0.0018 0.0021
z7 -0.0082 0.0126 -0.0056 0.0092 -0.0017 -0.0014
z8 -0.0028 -0.0155 -0.0030 0.0010 -0.0011 0.0012
z9 0.0019 0.0657 -0.0014 0.0021 -0.0016 0.0022
z10 0.0001 0.0509 0.0001 0.0052 -0.0021 0.0055
z11 0.0083 0.0852 0.0072 0.0012 -0.0017 0.0016
z12 -0.0405 -0.0067 -0.0105 -0.0050 -0.0023 0.0066
z13 0.0329 -0.0087 0.0311 -0.0016 0.0275 -0.0025
z14 0.0161 -0.0433 0.0253 -0.0015 0.0329 -0.0021
z15 0.0173 -0.0147 0.0114 -0.0012 0.0063 -0.0016
z16 0.0128 -0.0046 0.0196 -0.0035 0.0316 -0.0037
z17 0.0085 -0.0054 0.0082 -0.0061 0.0305 -0.0082
z18 -0.0058 0.0013 0.0315 -0.0047 0.0237 -0.0057
z19 -0.0018 0.0129 -0.0034 0.0135 -0.0063 -0.0138
z20 0.0096 -0.0276 0.0089 0.0019 0.0522 0.0021
z21 0.0525 -0.0058 0.0452 0.0010 0.0256 0.0015
z22 0.0148 0.0499 0.0511 0.0053 0.0666 0.0095
z23 -0.0012 -0.0057 0.0067 -0.0025 0.0086 -0.0012
z24 0.0003 -0.0046 0.0032 -0.0019 0.0173 -0.0027
z25 -0.0001 -0.0086 0.0016 -0.0052 0.0239 -0.0045
z26 0.0126 0.0074 0.0151 -0.0017 0.0181 -0.0061
z27 0.0083 0.0016 0.0092 0.0008 0.0308 -0.0008
z28 0.0243 0.0081 0.0195 0.0079 0.0194 -0.0019
z29 0.0298 0.0043 0.0211 0.0042 0.0204 -0.0043
z30 0.0047 -0.0075 0.0059 -0.0019 0.0079 -0.0011
z31 0.0022 0.0032 0.0032 0.0026 -0.0034 0.0023
z32 0.0011 0.0041 0.0010 0.0037 0.0029 -0.0014
5. CONCLUSIONS
Power system state estimation (SE) problem in this paper is solved as a constrained nonlinear
programming problem with various constraints and boundary limits on state variables. The proposed power
system SE problem is solved by using teaching leaning based optimization (TLBO) technique. The major
difference between TLBO and conventional optimization methods is that TLBO gives global optimal
solution for this proposed problem. The effectiveness and suitability of TLBO algorithm for solving SE
problem has been examined on IEEE 14 bus system. Results obtained with TLBO algorithm are also
compared with conventional WLS technique and evolutionary based PSO algorithm.
ACKNOWLEDGEMENTS
This research work has been carried out based on the support of “Woosong University's Academic
Research Funding – (2019-2020)”.
REFERENCES
[1] Zhao J, et al., “Power system dynamic state estimation: motivations, definitions, methodologies, and future work,”
IEEE Transactions on Power Systems, vol. 34, no. 4, pp. 3188-3198, July 2019.
[2] Singhal A, Rathour HK, et al., “State estimation at all India level,” National Power Systems Conference,
Bhubaneswar, pp. 1-6, 2016.

2131
[3] W. Gao, S. Wang, “On-line dynamic state estimation of power systems,” North American Power Symposium 2010,
Arlington, TX, pp. 1-6, 2010.
[4] M. A. Hussein and A. J. Sultan, “Enhancement of State Estimation Power System Based Hybrid Algorithm,” 2018
1st Annual International Conference on Information and Sciences (AiCIS), Fallujah, Iraq, pp. 164-169, 2018.
[5] H. Tebianian and B. Jeyasurya, "Dynamic state estimation in power systems using Kalman filters," 2013 IEEE
Electrical Power & Energy Conference, pp. 1-5, 2013.
[6] T. Okon and K. Wilkosz, “Comparison of weighted-least-squares power system state estimation in polar and
rectangular coordinate systems,” 2010 9th International Conference on Environment and Electrical Engineering,
pp. 140-143, 2010.
[7] Y. Yuehao, L. Hui, B. Wei, L. Zhaohui, Z. Hao and D. Yaoheng, "A distribution network state estimation method
based on power user electric energy data acquisition system," 2016 China International Conference on Electricity
Distribution (CICED), pp. 1-4, 2016.
[8] Brandalik R, Wellssow WH, “Power system state estimation with extended power formulations,” International
Journal of Electrical Power & Energy Systems, vol. 115, February 2020.
[9] Goleijani S., Ameli M. T., “A multi- agent based approach to power system dynamic state estimation by
considering algebraic and dynamic state variables,” Electric Power Systems Research, vol. 163, pp. 470-481,
October 2018.
[10] Rahman Md. A, Venayagamoorthy G. K., “A hybrid method for power system state estimation using Cellular
Computational Network,” Engineering Applications of Artificial Intelligence, vol. 64, pp. 140-151, September 2017.
[11] Tungadio D. H., Numbi B. P., et al., “Particle swarm optimization for power system state estimation,”
Neurocomputing, vol. 148, pp. 175-180, January 2015.
[12] Jiang X. T., Chow J. H., et al., “Power system state estimation using a direct non-iterative method,” International
Journal of Electrical Power & Energy Systems, vol. 73, pp. 361-368, December 2015.
[13] Vedik B., Chandel A. K., “Power system static state estimation using a least winsorized square robust estimator,”
Neurocomputing, vol. 207, pp. 457-468, September 2016.
[14] Tebianian H., Jeyasurya B., “Dynamic state estimation in power systems: Modeling, and challenges,” Electric
Power Systems Research, vol. 121, pp. 109-114, April 2015.
[15] Kabiri M., et al., “Enhancing power system state estimation by incorporating equality constraints of voltage
dependent loads and zero injections,” International Journal of Electrical Power & Energy Systems, vol. 99,
pp. 659-671, July 2018.
[16] A. K. Al-Othman and M. R. Irving, “Uncertainty modelling in power system state estimation,” IEE Proceedings
Generation, Transmission and Distribution, vol. 152, no. 2, pp. 233-239, March 2005.
[17] Gulati A., Gulati N., Solanki S. K., “Overview of State Estimation Technique for Power System Control,” IOSR
Journal of Electrical and Electronics Engineering, vol. 8, no. 5, pp. 51-55, December 2013.
[18] Manousakis N. M., Korres G. N., “A hybrid power system state estimator using synchronized and unsynchronized
sensors,” International Transactions on Electrical Energy Systems, vol. 28, no. 8, April 2018.
[19] P. Bartolomey and S. Semenenko, “Super-accelerated power systems power flow and state estimation calculations
within the WAMS environment,” 2017 14th International Conference on Engineering of Modern Electric Systems
(EMES), pp. 55-58, 2017.
[20] E. Ghahremani and I. Kamwa, “Local and Wide-Area PMU-Based Decentralized Dynamic State Estimation in
Multi-Machine Power Systems,” in IEEE Transactions on Power Systems, vol. 31, no. 1, pp. 547-562, Jan. 2016.
[21] H. Khazraj, F. Faria da Silva and C. L. Bak, “A performance comparison between extended Kalman Filter and
unscented Kalman Filter in power system dynamic state estimation,” 2016 51st International Universities Power
Engineering Conference (UPEC), pp. 1-6, 2016.
[22] Wang X, Zhao J, et al., “Fast robust power system dynamic state estimation using model transformation,”
International Journal of Electrical Power & Energy Systems, vol. 114, January 2020.
[23] Schmidt F., Almeida M. C., “A theoretical framework for qualitative problems in power system state estimation,”
Electric Power Systems Research, vol. 154, pp. 528-537, January 2018.
[24] Chen T., “Robust state estimation for power systems via moving horizon strategy,” Sustainable Energy, Grids and
Networks, vol. 10, pp. 46-54, June 2017.
[25] Chen T., Foo Y. S. E., et al., “Distributed State Estimation Using a Modified Partitioned Moving Horizon Strategy
for Power Systems,” Sensors, vol. 17, no. 10, 2017.
[26] Shahidehpour M, Marwali M, “Role of Fuzzy Sets in Power System State Estimation,” International Journal of
Emerging Electric Power Systems, vol. 1, no. 1, 2004.
[27] I. Akingeneye J. Wu and J. Yang, “Optimum PMU placement for power system state estimation,” 2017 IEEE
Power & Energy Society General Meeting, pp. 1-5, 2017.
[28] Khan Z., Razali R. B., et al., “State estimation of the power system using robust estimator,” AIP Conference
Proceedings, 2016.
[29] Bouchekara H. R. E. H., Abido M. A., et al., “Optimal power flow using Teaching-Learning-Based Optimization
technique,” Electric Power Systems Research, vol. 114, pp. 49-59, September 2014.
[30] Gill HS, Khehra BS, et al., “Teaching-learning-based optimization algorithm to minimize cross entropy for
selecting multilevel threshold values,” Egyptian Informatics Journal. vol. 20, no. 1, pp. 11-25, March 2019.
[31] R. R. Nucera and M. L. Gilles, “A blocked sparse matrix formulation for the solution of equality-constrained state
estimation,” IEEE Transactions on Power Systems, vol. 6, no. 1, pp. 214-224, Feb. 1991.
[32] Rogério M., Antonio S. C., et al., “Information Theoretic Generalized State Estimation in power systems,” Electric
Power Systems Research, vol. 182, May 2020.

Power system state estimation using teaching learning-based optimization algorithm

More Related Content

What's hot (20)

Similar to Power system state estimation using teaching learning-based optimization algorithm (20)

More from TELKOMNIKA JOURNAL (20)

Recently uploaded (20)

Power system state estimation using teaching learning-based optimization algorithm