Project List 1.3-May21,16- Substation Electrical Enginner
- 1. R REZA SHAH ABADI 104 – 4723 DAWSON STREET – BURNABY – BC – V5C 0A7, CELL: (604)655-2132, REZA10SHAH @YAHOO.COM 1/2 List of Noticeable Projects/ Maintenance Workshop Activities i. List of High voltage substations EPC projects: Kerman Province Miduk copper complex It was a project to provide around 150MW active power for Nicico expansion projects from 400KV nation power grid to 132KV Nicico’s network and 132KV regional power grid. It was an AIS green field project with One and a half breaker in 2*400KV bays switchyard and H type in 11*132KV feeders with 2*200MVA transformers. All utilities in Scada, Conventional Control, Protection, communication, AC/DC, Diesel generator, civil and construction, fencing, bus and cable work have been included in an EPC project. Azerbaijan Province Sungun copper complex It was a project to provide around 30MW active power for Nicico expansion project from 230KV nation power grid to 20KV Nicico’s network. It was an AIS brown field project to add a new 40 MVA transformer in a RING 230KV switchyard to provide a new 20KV feeder. All utilities in Scada, DCS Control, Protection, communication, AC/DC, MV switchgear, bus and cable work have been included in an EPC project. Sistan & Baluchistan Province Chehlkooreh copper complex It was a project to provide around 9MW active power for Nicico new project from 63KV regional power grid to 6.9KV Nicico’s new network. It was an AIS green field project with two incomings 63KV and 2*15MVA transformers. All utilities in Scada, Conventional Control, Protection, communication, AC/DC, civil and construction, fencing, bus and cable work, duct banks, MV switchgear have been included in an EPC project. Kerman Province Sarcheshmeh Copper Complex: In order to provide required power for expansion projects in this location, we have finalized the required Basic/Detail design and finding best location for three new substations: 230KV AIS Switching substations, One and a half breaker with 8 incoming and outgoings 230KV GIS Double-Busbar, 2*80MVA transformers 132KV GIS H type, 2*80MVA transformers ii. List of EPC ( Engineering, Procurement and Construction) Medium and Low voltage projects and its code in Sarcheshmeh Copper complex: E3: Switchgear and MCC: Replacing ten old LV Power center switchgears by new metal clad and well equipped ones and refurbishment the 20 air bus ducts and 130 ACBs. Replacing old MCC by new safer, divided compartment and well equipped ones. E7: Protection Relay and Automation: Replacing all old protection relays by numerical intelligent types, providing SAS for all substations (including remote mines and sites spread in 70 Sq. Km), SCADA, FDS ( Fundamental Design Specifications SAS/SCADA), Power Management System (PMS), Intelligent Load Shedding (ILS) for the factory’s power plant, Network Protocols DNP 3 and IEC61850, Providing a media of fiber optic, Radio system and Communication network, Human Machine Interface (HMI) software applications, LAN technologies, field/backbone switches, IP list, Signal List, SAS Architecture Diagrams, Hardware/Software Technical specification, Data Base configuration, Time Synchronization
- 2. R REZA SHAH ABADI 104 – 4723 DAWSON STREET – BURNABY – BC – V5C 0A7, CELL: (604)655-2132, REZA10SHAH @YAHOO.COM 2/2 E8: Switchgear GIS and Breakers: Replacing all different types minimum oil circuit breakers and SF6 circuit breaker on trucks with Vacuum CB, replacing an MV Air Insulation Switchgear by a metal clad semi GIS with a complete SAS/numerical relays/power quality meters systems, Installation the tuned MV filter banks, Installation PASS systems, design for installation of an IS-Limiter, replacement two in-box- Disconnector Switches with their enclosures with new ones, replacing two air bus ducts with the fully insulated ones ….. E9: Transformers and Ring Main Units: Replacing the 42 distribution Askarel (PCB) oil immerse transformers by cast resin dry types and exporting the oil and contaminated equipment to disposal plant in France. In this project we replaced 16 Oil Immersed LBSs by metal enclosed GIS RMUs Note: Energy Globe (An International Foundation in Austria) awarded National Award in 2013 for this project and the project was a candidate for Energy Globe International Award in 2013 as well. E13: Partial Discharge: Installation online and offline partial discharge measurement and monitoring system for MV machines (45 units including Generators 11 & 6.9KV and Electromotors 6.9KV) based on North American method in the production lines. Furthermore, providing a portable measurement PD system for switchgears, electromotors, cables and terminators based on European method. E17: Skid Mounted Substations: Replacing 3 old and conventional mining substations 5MVA, 20/6.9KV and 12 mining 6.9KV switchboxes by new mobile and skid mounted ones. They are equipped by numerical relay, Power Quality Meters and Broadband Power Line carrier data systems on MV cables. E20: Transformers and Cable Duct Banks: Expanding electrical distribution network (including 11 transformer substations, 12KV metal enclosed switchgear with 22 feeders, encapsulated resin bus ducts, 20 Km triplex 20/12KV cables, 1200 meter duct bank, 16 manholes, 35 distribution industrial transformers 20/6.9KV & 20/0.4KV, 45 units metal clad semi GIS, plug in terminators, etc.) for the new consumer to feed 40MW new plants. iii. List of High voltage Transmission line PC projects: 400, 132 KV in Kerman Province 70km 63KV in Azerbaijan Province 15km 230, 63 KV in Sistan & Baluchistan Province 120km iv. Noticeable Workshop Maintenance Activities: Rewinding MV Electromotor Stator: Complete rewinding a Stator of 4500hp, 30poles, 200RMP, 6900 Volt, Synchronous Mill Electromotors GE Canada in workshop with all required tests Overhauls of Stators Gas Turbine Generators and checking all parts of insulation windings 11Kv, 25MW Alstom Frame 5 Predict the insulation life lasting by doing all required tests on a Waste Heat Steam Generator Stator 6900 Volts, 10MW GE to Rewinding Transformer: 2MVA, 20KV/6.9KV Inspection on rewinding/maintenance of a variety range of MV electromotors in off-site workshop