Q3A(R2)
- 1. ICH GUIDELINES IMPURITIES IN NEW DRUG SUBSTANCES Q3A(R2) PRACHI JOSHI M.S. (PHARM) PHARMACEUTICS
- 2. Contents • Introduction to Q3A (R2). • Definitions. • Classification of Impurities. • Rational for the Reporting and Control of Impurities. • Analytical Procedure. • Reporting Impurity Content of Batches. • Listing Of Impurities in Specification. • Qualification Of Impurities. • Thresholds. • Decision Tree.
- 3. Introduction • This document is intended to provide guidance for registration applications on the content and qualification of impurities in new drug substances produced by chemical synthesis and not previously registered in a region or member state. • The following types of drug substances are not covered in this guideline: biological/biotechnological, peptide, oligonucleotide, radiopharmaceutical, fermentation product and semi-synthetic products derived therefrom, herbal products, and crude products of animal or plant origin.
- 4. Impurities in new drug substances are addressed from two perspectives: • Chemistry Aspects include classification and identification of impurities, report generation, listing of impurities in specifications, and a brief discussion of analytical procedures. • Safety Aspects include specific guidance for qualifying those impurities that were not present, or were present at substantially lower levels, in batches of a new drug substance used in safety and clinical studies.
- 5. Definitions • Enantiomeric Impurity: A compound with the same molecular formula as the drug substance that differs in the spatial arrangement of atoms within the molecule and is a non-superimposable mirror image. • Identified Impurity: An impurity for which a structural characterization has been achieved. • Identification Threshold: A limit above (>) which an impurity should be identified. • Impurity: Any component of the new drug substance that is not the chemical entity defined as the new drug substance.
- 6. • Impurity Profile: A description of the identified and unidentified impurities present in a new drug substance. • Qualification: The process of acquiring and evaluating data that establishes the biological safety of an individual impurity or a given impurity profile at the level(s) specified. • Qualification Threshold: A limit above (>) which an impurity should be qualified. • Reporting Threshold: A limit above (>) which an impurity should be reported. Reporting threshold is the same as reporting level in Q2B. • Specified Impurity: An impurity that is individually listed and limited with a specific acceptance criterion in the new drug substance specification. A specified impurity can be either identified or unidentified.
- 7. Classification Of Impurities IMPURITIES RESIDUAL SOLVENTS INORGANIC IMPURITIES ORGANIC IMPURITIES Excluded from this document are: o Extraneous contaminants that should not occur in new drug substances (GMP). o Polymorphic forms. o Enantiomeric impurities.
- 8. Organic Impurities • It can arise during the manufacturing process and/or storage of the new drug substance. • They can be identified or unidentified, volatile or non-volatile, and include: o Starting materials o By-products o Intermediates o Degradation products o Reagents, ligands and catalysts
- 9. Inorganic Impurities • Inorganic impurities can result from the manufacturing process. • They are normally known and identified and include: o Reagents, ligands and catalysts o Heavy metals or other residual metals o Inorganic salts o Other materials (e.g., filter aids, charcoal)
- 10. Residual Solvents • Solvents are inorganic or organic liquids used as vehicles for the preparation of solutions or suspensions in the synthesis of a new drug substance. • Generally known for their toxicity. • The term "tolerable daily intake" (TDI) is used by the International Program on Chemical Safety (IPCS) to describe exposure limits of toxic chemicals. • “Acceptable daily intake" (ADI) is used by the World Health Organization (WHO) and other national and international health authorities and institutes. • The new term "permitted daily exposure" (PDE) is defined in the present guideline as a pharmaceutically acceptable intake of residual solvents.
- 11. Classification Of Residual Solvents Class 1 solvents: Solvents to be avoided Known human carcinogens, strongly suspected human carcinogens, and environmental hazards. e.g. Benzene, CCl4 Class 2 solvents: Solvents to be limited Non-genotoxic animal carcinogens or possible causative agents of other irreversible toxicity such as neurotoxicity or teratogenicity. Class 2 solvents have PDEs of near to 0.1 mg per day. Solvents suspected of other significant but reversible toxicities. e.g. Acetonitrile, Chlorobenzene, CHCl3 Class 3 solvents: Solvents with low toxic potential Solvents with low toxic potential to man; no health-based exposure limit is needed. Class 3 solvents have PDEs of 50 mg or more per day. e.g. Acetic acid, Ethanol, Acetone.
- 12. Rational For the Reporting and Control Of Impurities For Organic Impurities • The applicant should summaries the actual and potential impurities most likely to arise during the synthesis, purification, and storage of the new drug substance. • This summary should be based on the chemical reactions involved in the synthesis, impurities associated with raw material. • In addition, the applicant should summaries the laboratory studies conducted to detect impurities in the new drug substance. • This summary should include test results of batches manufactured to determine the impurity profile
- 13. o The studies conducted to characterise the structure of actual impurities present in the new drug substance at a level greater than (>) the identification threshold should be described. o Any impurity at a level greater than (>) the identification threshold in any batch manufactured by the proposed commercial process should be identified. o Any degradation product observed in stability studies at recommended storage conditions at a level greater than (>) the identification threshold should be identified. o When identification of an impurity is not feasible, a summary of the laboratory studies demonstrating the unsuccessful effort should be included in the application. o Analytical procedures should be developed for those potential impurities that are expected to be unusually potent, producing toxic or pharmacological effects at a level not more than (≤) the identification threshold.
- 14. For Inorganic Impurities • Inorganic impurities are normally detected and quantified using pharmacopoeial or other appropriate procedures. • The need for inclusion or exclusion of inorganic impurities in the new drug substance specification should be discussed. • Acceptance criteria should be based on pharmacopoeial standards or known safety data. For Solvents • The control of residues of the solvents used in the manufacturing process for the new drug substance should be discussed and presented according to the ICH Q3C Guideline for Residual Solvents.
- 15. Analytical Procedure • The registration application should include documented evidence that the analytical procedures are validated and suitable for the detection and quantification of impurities (As per given in ICH Q2A and Q2B Guidelines for Analytical Validation). • The use of lower precision techniques (e.g., thin-layer chromatography) can be acceptable where justified and appropriately validated. • Differences in the analytical procedures used during development and those proposed for the commercial product should be discussed in the registration application. • The quantitation limit for the analytical procedure should be not more than (≤) the reporting threshold.
- 16. • The drug substance can be used as a standard to estimate the levels of impurities. • Reference standards used in the analytical procedures for control of impurities should be evaluated and characterized according to their intended uses. • Acceptance criteria and analytical procedures used to estimate identified or unidentified impurities can be based on analytical assumptions (e.g., equivalent detector response).
- 17. Reporting Impurity Content Of Batches • Analytical results should be provided in the application for all batches of the new drug substance used for clinical, safety, and stability testing, as well as for batches representative of the proposed commercial process. • Quantitative results should be presented numerically, and not in general terms such as “complies”, “meets limit” etc. • Below 1.0%, the results should be reported to two decimal places (e.g., 0.06%, 0.13%); at and above 1.0%, the results should be reported to one decimal place (e.g., 1.3%). • A tabulation (e.g., spreadsheet) of the data is recommended.
- 18. • When analytical procedures change during development, reported results should be linked to the procedure used, with appropriate validation information provided. • The applicant should ensure that complete impurity profiles (e.g. chromatograms) of individual batches are available, if requested. • For each batch of the new drug substance, the report should include: o Batch identity and size o Date of manufacture o Site of manufacture o Manufacturing process o Impurity content, individual and total o Use of batches o Reference to analytical procedure used
- 19. Listing Of Impurities In Specifications • The specification for a new drug substance should include a list of impurities. • Stability studies, chemical development studies, and routine batch analyses can be used to predict those impurities likely to occur in the commercial product. • A rationale for the inclusion or exclusion of impurities in the specification should be presented. • For impurities known to be unusually potent or to produce toxic or unexpected pharmacological effects, the quantitation/detection limit of the analytical procedures should be commensurate with the level at which the impurities should be controlled.
- 20. Qualification Of Impurities • Qualification is the process of acquiring and evaluating data that establishes the biological safety of an individual impurity or a given impurity profile at the level(s) specified. • Applicant should provide a rationale for establishing impurity acceptance criteria that includes safety considerations. • The level of any impurity present in a new drug substance that has been adequately tested in safety and/or clinical studies would be considered qualified. • A level of a qualified impurity higher than that present in a new drug substance can also be justified based on an analysis of the actual amount of impurity administered in previous relevant safety studies.
- 21. • Higher or lower thresholds for qualification of impurities can be appropriate for some individual drugs based on scientific rationale and level of concern, including drug class effects and clinical experience. For example, qualification can be especially important when there is evidence that such impurities in certain drugs or therapeutic classes have previously been associated with adverse reactions in patients • The "Decision Tree for Identification and Qualification“ describes considerations for the qualification of impurities when thresholds are exceeded. • Although this guideline is not intended to apply during the clinical research stage of development, in the later stages of development the thresholds in this guideline can be useful in evaluating new impurities observed in drug substance batches prepared by the proposed commercial process.
- 22. Maximum Daily Dose1 Reporting Threshold2 Identification Threshold3 Qualification Threshold3 2g/day 0.05% 0.10% or 1.0 mg per day intake (whichever is lower) 0.15% or 1.0 mg per day intake (whichever is lower) > 2g/day 0.03% 0.05% 0.05% 1 The amount of drug substance administered per day. 2 Higher reporting thresholds should be scientifically justified. 3 Lower thresholds can be appropriate if the impurity is unusually toxic. Thresholds
- 23. Decision Tree for Identification & Qualification
- 24. THANK YOU