Response History Analysis of Structures SAP2000.pdf

~ULTIDISCIPLINARY CENTER FOR EARTHQUAKE ENGINEERING RESEARCH
ANational Center of Excellence in Advanced TeChnology Applications
SSN 1520-295X 1111111111111111111111111111111
PB99-162869
Response History Analysis of Structures
with Seismic Isolation and Energy Dissipation
Systems: Verification Examples for
Program SAP2000
by
Joern Scheller and Michael C. Constantinou
University at Buffalo, State University of New York
School of Civil, Structural and Environmental Engineering
Ketter Hall
Buffalo, New York 14260-4300
Technical Report MCEER-99-0002
February 22, 1999
REPRODUCED BY: ~
U.S. Department of Commerce .._-
National Technical Information Service
Springfield, Virginia 22161
This research was conducted at the University at Buffalo, State University of New York and was
supported in whole or in part by the National Science Foundation under Grant No. eMS 97-01471.

PROTECTED UNDER INTERNATIONAL COPYRIGHT
ALL RIGHTS RESERVED.
NATIONAL TECHNICAL INFORMATION SERVICE
U.S. DEPARTMENT OF COMMERCE
NOTICE
This report was prepared by the University at Buffalo, State University of New
York as a result of research sponsored by the Multidisciplinary Center for Earth-
quake Engineering Research (MCEER) through a grant from the National Science
Foundation and other sponsors. Neither MCEER, associates of MCEER, its spon-
sors, University at Buffalo, State University of New York, nor any person acting on
their behalf:
a. makes any warranty, express or implied, with respect to the use of any infor-
mation, apparatus, method, or process disclosed in this report or that such use
may not infringe upon privately owned rights; or
b. assumes any liabilities of whatsoever kind with respect to the use of, or the
damage resulting from the use of, any information, apparatus, method, or pro-
cess disclosed in this report.
Any opinions, findings, and conclusions or recommendations expressed in this
publication are those of the author(s) and do not necessarily reflect the views of
MCEER, the National Science Foundation, or other sponsors.

50272-101
1111111111111111111111111111111
REPORT DOCUMENTATION 1. Report No. 3. Recipient's Accession No.
PAGE MCEER-99-0002
PB99-162869
4. Title and Subtitle 5. Report Date
Response History Analysis of Structures with Seismic Isolation and Energy Dissipation Systems: Verification February 22, 1999
Examples for Program SAP2000
6.
7. Authors 8. Performing Organization Report No.
Joern Scheller and Michael C. Constantinou
10. Project/TaskIWork Unit No.
98-2403
9.Performing Organization Name and Address 11. Contract(C lor Grant (G) No.
School of Civil, Structural and Environmental Engineering (C) CMS 97-01471
State University of New York at Buffalo
(G)
Ketter Hall
Buffalo, New York 14260
12. Sponsoring Organization Name and Address 13. Type of Report &Period Covered
Multidisciplinary Center for Earthquake Engineering Research Technical report
State University of New York at Buffalo
Red Jacket Quadrangle, Buffalo, NY 14261
14.
15. Supplementary Notes
This research was conducted at the University at Buffalo, State University of New York and was supported in whole or in part by the National Science
Foundation under Grant No. CMS 97-01471.
16. Abstract (limit 200 words)
SAP2000 is arecently released commercial structural analysis program with capabilities for dynamic analysis of structures with isolation and energy
dissipation systems. This report presents five verification examples in which results obtained by SAP2000 are compared to experimental results and to
results obtained by programs 3D-BASIS and ANSYS. Three of the examples involve seismically isolated structures, of which, one was tested on the
shake table under conditions resulting in bearing uplift. The other two examples involve structures with linear and nonlinear fluid viscous energy
dissipation devices, which were also tested on the shake table. In general, SAP2000 produced results in excellent agreement with other analysis
programs and in good agreement with experimental results, except for the case of the structures tested with nonlinear viscous damping devices. In this
case, SAP2000 underpredicted the displacement response of the structure.
17. Document Analysis a. Descriptors
Earthquake engineering. SAP2000. Dynamic analysis. Isolation systems. Energy dissipation systems. Shear-type frames. Toggle brace dampers.
Liquid storage tanks. Friction pendulum isolation systems. Linear viscous fluid dampers. Nonlinear viscous fluid dampers. Modeling.
b. Identifiers/Open-Ended Terms
c. COSATI Field/Group
18. Availability Statement 19. Security Class (This Report) 21. No. of Pages
Release unlimited. Unclassified 123
20. Security Class (This Page) 22. Price
Unclassified
(see ANSIJ39.18)

Response History Analysis of Structures with
Seismic Isolation and
Energy Dissipation Systems:
Verification Examples for Program SAP2000
by
Joem Scheller and Michael C. Constantinou
Publication Date: February 22, 1999
Submittal Date: November 10, 1998
Technical Report MCEER-99-0002
Task Number 98-2403
NSF Master Contract Number CMS 97-01471
1 Graduate Assistant, Department of Civil, Structural and Environmental Engineering, Univer-
sity at Buffalo, State University of New York
2 Professor, Department of Civil, Structural and Environmental Engineering, University at
Buffalo, State University of New York
MULTIDISCIPLINARY CENTER FOR EARTHQUAKE ENGINEERING RESEARCH
University at Buffalo, State University of New York
Red Jacket Quadrangle, Buffalo, NY 14261

Preface
The Multidisciplinary Centerfor EarthquakeEngineering Research (MCEER) is a national center of
excellencein advancedtechnology applications thatis dedicatedto thereductionofearthquakelosses
nationwide. Headquartered at the University at Buffalo, State University of New York, the Center
was originally established by the National Science Foundation in 1986, as the National Center for
Earthquake Engineering Research (NCEER).
Comprising a consortium of researchers from numerous disciplines and institutions throughout the
United States, the Center's mission is to reduce earthquake losses through research and the
application of advanced technologies that improve engineering, pre-earthquake planning and post-
earthquake recovery strategies. Toward this end, the Center coordinates a nationwide program of
multidisciplinary team research, education and outreach activities.
MCEER's research is conducted under the sponsorship of two major federal agencies: the National
Science Foundation (NSF) and the Federal Highway Administration (FHWA), and the State ofNew
York. Significant support is derived from the Federal Emergency Management Agency (FEMA),
other state governments, academic institutions, foreign governments and private industry.
The Center's NSF-sponsored research is focused around four major thrusts, as shown in the figure
below:
• quantifying building and lifeline performance in future earthquake through the estimation of
expected losses;
• developing cost-effective, performance based, rehabilitation technologies for critical facilities;
• improving response and recovery through strategic planning and crisis management;
• establishing two user networks, one in experimental facilities and computing environments and
the other in computational and analytical resources.
I. Performance Assessment of the Built Environment
.. using
Loss Estimation Methodologies
!
IV. User Network
II. Rehabilitation of Critical Facilities
• Facilities Network .. using
• Computational Network Advance Technologies
~ !
III. Response and Recovery
~ using
Advance Technologies
iii

SAP2000 is the latestversion in thepopularSAP seriesofcommercialstructuralanalysisprograms.
Itwas releasedin 1997andcan be usedfor the dynamic analysisofstructureswith seismic isolation
andenergy dissipation systems. In this report, five examples are used to verify the results obtained
by SAP2000. Three ofthe examples involved seismically isolated structures: an 8-story building
isolatedwith bearings, a liquidstorage tankisolatedwith africtionpendulum isolation system, and
a 7-story bUilding model isolated with a friction pendulum system. Results from the 3D-BASIS
analysisprogram andexperimental testingwere comparedto the SAP2000 analysis, andproduced
excellent agreement. The other two examples involved structures with energy dissipation devices:
a 3-story buildingmodelwith linearandnonlinearviscousfluiddampers, anda modelwith a toggle
brace-damperenergy dissipation system. Resultsfrom theANSYSanalysisprogram andexperimen-
tal testing were compared to the SAP2000 analysis, where most results were in good agreement.
However, SAP2000 under-predicted the displacement response ofthe structure testedwith nonlin-
ear viscous dampers.
The input files for the programs used, the history ofthe seismic excitation and the experimental
results are located in the Publications section ofMCEER's web site (http://mceer.buffalo.edu/
pubs.htm/).
iv

ABSTRACT
SAP2000 is a recently released commercial structural analysis program with
capabilities for dynamic analysis of structures with seismic isolation and energy
dissipation systems. This repOli presents five verification examples in which results
obtained by SAP2000 are compared to experimental results and to results obtained by
programs 3D-BASIS and ANSYS. Three of the examples involve seismically isolated
structures, of which one was tested on the shake table under conditions resulting in
bearing uplift. The other two examples involve structures with linear and nonlinear fluid
viscous energy dissipation devices, which were also tested on the shake table. In general,
SAP2000 produced results in excellent agreement with other analysis programs and in
good agreement with experimental results, except for the case of the structure tested with
nonlinear viscous damping devices. In this case, SAP2000 underpredicted the
displacement response of the structure.
v

ACKNOWLEDGEMENTS
Partial financial support for this project was provided by the Multidisciplinary
Center for Earthquake Engineering Research, Project No. 98-2403. The authors are
grateful to Dr. Andrew S. Whittaker for his comprehensive review ofthis report.
Vll

TABLE OF CONTENTS
SECTION TITLE PAGE
1 INTRODUCTION 1
2 ANALYSIS OF AN 8-STORY SEISMICALLY ISOLATED
BUILDING WITH BEARINGS 5
2.1 Introduction 5
2.2 Description of Analyzed Structure 7
2.3 Modeling in 3D-BASIS-ME and SAP2000 9
2.4 Comparison of Results 13
3 ANALYSIS OF A LIQUID STORAGE TANK WITH
THE FRICTION PENDULUM ISOLATION SYSTEM 25
3.1 Introduction 25
3.2 Description of Analyzed Liquid Storage Tank 27
,.., ,..,
Modeling of Liquid Storage Tank in 3D-BASIS-ME 29
j.j
3.4 Modeling of Liquid Storage Tanks in SAP2000 30
3.5 Comparison of Results 35
4 ANALYSIS OF EXPERIMENTAL RESPONSE OF A
7-STORY BUILDING MODEL WITH FRICTION
PENDULUM ISOLATION SYSTEM 43
4.1 Introduction 43
4.2 Description of Tested Structure 43
4.3 Modeling in SAP2000 46
4.4 Analysis Results and Comparison to Experiment 50
3-STORY BUILDING MODEL WITH LINEAR AND
NONLINEAR VISCOUS FLUID DAMPERS 61
5.1 Introduction 61
IX

TABLE OF CONTENTS (continued)
SECTION TITLE PAGE
MODEL WITH A TOGGLE BRACE-DAMPER
ENERGY DISSIPATION SYSTEM 75
6.1 Introduction 75
7 CONCLUSIONS 87
8 REFERENCES 89
x

LIST OF ILLUSTRATIONS
FIGURE TITLE PAGE
2-1 Plan View of the Base of the Building Model and Location of
the Isolation Bearings 8
2-2 Illustration of SAP2000 Model of 8-story Seismic-Isolated
Building 12
2-3 Comparison of Calculated Force-Displacement Loops for
Corner Bearing 14
Center Bearing 15
2-5 Comparison of Calculated 8th Story Drift Histories 16
2-6 Comparison of Calculated 3rd Story Drift Histories 17
2-7 Comparison of Calculated 8th Floor Acceleration Histories 18
2-8 Comparison of Calculated 3rd Floor Acceleration Histories 19
2-9 Comparison of Calculated Relative Story Rotation Histories 20
Corner Bearing when the Actual Value ofke is Used 22
Center Bearing when the Actual Value ofke is Used j"
_.J
3-1 Geometry of Isolated Water Tank 28
3-2 Configuration ofIsolation System 28
" " Mathematical Model of Liquid Storage Tank 29
.J-.J
3-4 Model of Liquid Storage Tank in 3D-BASIS-ME 31
3-5 Location of Clusters of Bearings in 3D-BASIS-ME 32
Central Cluster of Bearings (No.5) 36
Xl

LIST OF ILLUSTRATIONS (continued)
FIGURE TITLE PAGE
Exterior Cluster of Bearings (No.1) 37
3-8 Comparison of Calculated Displacements of Sloshing Fluid 38
3-9 Comparison of Calculated Displacements of Fluid-Tank Mode 39
3-10 Comparison of Calculated Accelerations of Sloshing Fluid 40
3-11 Comparison of Calculated Accelerations of Fluid-Tank Mode 41
4-1 Elevations and Plan View of Tested Structure 44
4-2 Model of 7-story Isolated Structure in SAP2000 47
4-3 Comparison of Analytical and Experimental Results on the
Base Shear-Displacement Loop and Isolation System
Displacement History 52
4-4 Comparison of Analytical and Experimental Results on
Selected Histories of Story Drift and Story Shear Force 53
the 7th Floor Acceleration 54
4-6 Comparison of Analytical and Experimental Shear Force-
Bearing Displacement Loops 55
the Base Shear Displacement Loop. Analysis without
Damping Elements 58
Shear Force-Displacement Loops. Analysis with Vertical
Elements and Realistic Values of Linear Effective Stiffness 59
5-1 Schematic of Tested Model 63
5-2 Schematic of One of the Tested Configurations 64
5-3 Illustration of SAP2000 Model of 3-story Frame with Viscous
Dampers 65
xu

LIST OF ILLUSTRATIONS (continued)
FIGURE TITLE PAGE
5-4 Comparison of Analytical and Experimental Normalized Story
Shear Force-Drift Loops of Structure with Linear Dampers
(linear analysis type, linear damper model) 68
5-5 Comparison of Analytical and Experimental Histories
of Drift of Structure with Linear Dampers (linear analysis
type, linear damper model) 69
Shear Force-Drift Loops of Structure with Linear Dampers
(nonlinear analysis type, nonlinear damper model with
cexp = 1.0) 71
Shear Force-Drift Loops of Structure with Nonlinear Dampers 72
5-8 Comparison of Analytical and Experimental Histories
of Drift of Structure with Nonlinear Dampers 73
6-1 Tested Frame with Toggle Brace-Damper System 76
6-2 View of Tested Structure with Upper Damper Configuration
on the Shaking Table 77
6-3 Schematic Illustrating Joints and Elements in ANSYS Model
of Frame with Rigid-Simple Connections (for coordinates and
section properties see Appendix F) 80
6-4 Schematic Illustrating Location of Lumped Masses in ANSYS
Model of Frame (values denote weight in pounds) 81
6-5 Comparison of Analytical and Experimental Results on History
of Frame Drift 83
6-6 Comparison of Analytical and Experimental Damper Force-
Displacement Loops 84
6-7 Comparison of Analytical and Experimental Histories of
Acceleration of Beam to Column Connection 85
Xlll

LIST OF TABLES
TABLE TITLE PAGE
2-1 Properties of Analyzed Structure 7
2-2 Comparison of Calculated Periods and Mode Shapes of
8-story Superstructure (fixed base) 10
4-1 Experimental and Analytical Modal Properties of Non-isolated
7-story Model 51
5-1 Experimental and Analytical Modal Properties of 3-story
Model without Dampers 67
xv

SECTION 1
INTRODUCTION
Seismic isolation and energy dissipation technologies have found an increasing
number of applications over the last decade and particularly over the last few years
following the 1994 Northridge earthquake. The increase in the use of these technologies
may be attributed to (a) the further development of these technologies and the transfer of
technologies from other disciplines, (b) the need to retrofit or rehabilitate seismically
deficient structures, (c) the desire to improve performance in new construction, (d) the
development of analysis and design guidelines and specifications, and (e) the availability
of computer programs for dynamic analysis.
Commercially available computer programs, such as ANSYS (Swanson Analysis
Systems, 1996) and ABAQUS (Hibbitt et ai., 1989), have been available for several years
and are capable of modeling the behavior of seismic isolation and energy dissipation
hardware. However, they have been rarely used for this purpose primarily because they
are general purpose analysis programs not suited to the analysis of buildings.
The need for a dynamic analysis computer program dedicated to seismically
isolated buildings was flllfilled in part with the release in 1989 of 3D-BASIS
(Nagarajaiah et al., 1989). Various versions of this program have been released since
then, of which 3D-BASIS-TABS (Reinhorn et ai., 1994) and 3D-BASIS-ME (Tsopelas et
al., 1994) introduced new features such as integration with program ETABS (Wilson et
al., 1975), multiple superstructures, elements for viscous dampers, and vertical ground
acceleration and overturning moment effects on sliding isolation bearings.
1

In 1997 program SAP2000 was released (Computers and Structures, 1997). As
the latest version in the popular SAP series of commercial structural analysis programs,
SAP2000 has the feature of nonlinear dynamic analysis with elements for seismic
isolation and energy dissipation hardware. The program has already been used for the
analysis of a number of structures with seismic isolation or energy dissipation systems,
and has the potential for widespread use.
In this report, a series of verification examples for SAP2000 are presented
involving seismic isolation and energy dissipation systems. Two of the problems are
special structural systems in which a specific type of behavior is sought (e.g., shear-type
representation, exclusion of overturning moment effects, etc.). Results obtained by
SAP2000 are compared with results obtained by program 3D-BASIS-ME (Tsopelas et
al., 1994). Three more examples involve structures tested in the laboratory for which
experimental results are available. They include one structure with Friction Pendulum
isolation bearings under extreme conditions of dynamic loading that induce bearing
upl ift. and two structures with linear and nonlinear viscous fluid dampers. Moreover. in
one of the last three problems. the SAP2000 results are compared to those obtained by
program ANSYS (Swanson Analysis Systems, 1996).
In general. modeling in SAP2000 was successful in producing results that were
either nearly identical to those of programs 3D-BASIS-ME and ANSYS or in favorable
agreement with experimental results. However, modeling in SAP2000 was not always
straightforward and in some cases, an uncommon combination of elements was used to
obtain the correct response. Moreover, the nonlinear viscous damper element in
SAP2000 was observed to lead to underestimation of story drifts in the analysis of a
2

tested 3-story structure. However, the same model performed properly in the analysis of
simple single degree of freedom systems.
In the verification examples, a mixture of units in the 51 and in the American
systems were used, exactly as they were used in the original publications of the analytical
or experimental results which were used to verify SAP2000.
The input files for the programs used, the history of the seismic excitation and the
experimental results are provided on MCEER's web site at http://mceer.bufJalo.edu.
3

SECTION 2
ANALYSIS OF AN 8-STORY SEISMICALLY ISOLATED BUILDING
WITH BEARINGS
2.1 Introduction
In this example, a rather simple representation of a seismically isolated building is
analyzed using SAP2000 (Computer and Structures, 1997) and the results are compared
to results obtained with program 3D-BASIS-ME (Tsopelas et ai., 1994). Due to the
simplicity of the model for this structural system-shear-type representation with bilinear
hysteretic isolators-3D-BASIS-ME is believed to produce accurate results. Accordingly,
the example serves the purpose of demonstrating the SAP2000 input and particularly the
configuration ofthe Nllink element for producing output that is nearly identical to that of
3D-BASIS-ME.
The analyzed structural system has been used by Theodossiou and Constantinou
(1991) and Winters and Constantinou (1993) in the evaluation of the SEAOC/UBC
analysis procedures for seismically isolated structures. In these studies, an 8-story
building superstructure was modeled as shear-type frame with its properties specified in
terms of the floor masses and moments of inertia, story shear and rotational stiffnesses,
eccentricities and modal damping ratios. The isolation system consisted of 45 isolators
with bilinear hysteresis
There are various options for modeling shear-type behavior in SAP2000. One
option is to utilize the Frame element for columns with appropriate axial stiffness so that
they are effectively inextensible. Another option is to use the Nllink element in the
5

damper property type. This element is described in the SAP2000 Analysis Reference
(Computer and Structures, 1997) as a Maxwell element, that is, an element consisting of
a damper and a spring in series. There is no mention in the SAP2000 Analysis Reference
as to how this element may be used to represent a pure spring. One would expect that by
specifying a large value for the damping coefficient c, pure spring behavior could be
obtained, but such behavior is obtained in SAP2000 when c is specified to be zero.
The isolation bearings, which have bilinear hysteretic behavior, were modeled
with element Nllink in the Isolatorl property type. This element has coupled bilinear
hysteretic behavior for the two shear defonnations, whereas the remaining four degrees
of freedom (axial deformation and three rotations) are linear. Among the parameters
describing this model, the linear effective stiffness ke for the two nonlinear degrees of
freedom needs to be specified. This parameter is not directly used for the nonlinear time-
history analysis. Rather, it is used indirectly. According to the SAP2000 Analysis
Reference its selected value may affect the rate of convergence in the iterative solution
procedure; no mention is made as to the effect of the selected value on the accuracy of
the solution.
It appears that an appropriate value of the linear effective stiffness for the
nonlinear degrees of freedom is the effective stiffness of the isolator as, for example, is
defined in the Uniform Building Code (e.g., International Conference of Building
Officials, 1994). When such a value is used, the calculated frequencies and mode shapes
of the structure are meaningful and useful for response-spectrum analysis. However, we
observed that when this value is used in nonlinear time-history analysis, the calculated
response IS incorrect. Specifically, the isolation-system displacements are
6

underestimated. On the other hand, correct results are obtained when the value of ke is
specified to be very small but not zero (a zero value would result in an unstable system
and execution of the program is aborted).
2.2 Description of Analyzed Structure
The structure is an eight-story building with plan dimensions of 160 ft by 80 ft
with a story height of 12 ft. The properties of the structure in a shear-type representation
are given in Table 2-1. In this representation the center of resistance of each story is
located at the geometric center, whereas the center of mass of each floor and of the
isolation basemat is located at distance of 8 ft from the geometric center as illustrated in
Figure 2-1.
Table 2-1 Properties of Analyzed Structure
Story Weight Rotational Stiffness Rotational Eccentricity
/ (kips) Inertia (kips/in) Stiffness (ft)
Floor (kips-in-sec2
) (kips-in) Longitudinal Transverse
8 1280 1272642.5 1700.9 1997933760 8 0
7 1280 1272642.5 1700.9 1997933760 8 0
6 1280 1272642.5 2551.3 2996900640 8 0
5 1280 1272642.5 2551.3 2996900640 8 0
4 1280 1272642.5 2551.3 2996900640 8 0
3 1280 1272642.5 3401.8 3995867520 8 0
2 1280 1272642.5 3401.8 3995867520 8 0
1 1280 1272642.5 3401.8 3995867520 8 0
Base 1280 1272642.5 8 0
Figure 2-1 shows also the location of the 45 isolation bearings. Each of these
bearings has bilinear hysteretic behavior with yield force of 12.8 kips, yield displacement
of 0.5 inch and ratio of post-yielding to elastic stiffness of 0.18868. This isolation system
7

r
I
-+-+-+-
I I I
-~-.--+--
I I I
I I I
--.--.---.--
I ~g'l
--+--f-+-
I 1 I
-- ....- - • - -+- -
I I I
I I I
- -.-- .- -.--
o
1.0
II
o
N
x
I I I
--+--+-+- J
~
~4 x 20' = 80' -l
ISOLATION
BEARING (TYP.)
L
'------ T
Figure 2-1 Plan View of the Base of the Building Model and Location of the
Isolation Bearings
IS referred to as system type 7 for stiff soil profiles in the study of Winters and
Constantinou (1993). The isolation system was configured for seIsmIC input
representative of Seismic Zone 4, soil profile SI, and at a site at least 15 km from an
active fault in accordance with the 1994 Uniform Building Code (International
Conference of Building Officials, 1994). On the basis of the static analysis procedure of
the 1994 Uniform Building Code, the isolated-structure period is 2.0 sec, the effective
damping is 0.16 and the design displacement is 5.8 in.
8

The seismic input for this example consisted of the recorded pair of horizontal
ground acceleration histories in the 1971 San Fernando earthquake at station No. 211.
Each of the two components was mUltiplied by a factor 2.345 in accordance with the
scaling procedures described in Theodossiou and Constantinou (1991) and applied with
the north and west components in the transverse and longitudinal directions of the model,
respectively.
2.3 Modeling in 3D-BASIS-ME and SAP20()O
The model of the 8-story superstructure in program 3D-BASIS-ME utilized the
shear-type option. Each of the 45 isolators was explicitly modeled using the hysteretic
element for elastomeric bearings (option INELEM (K, 2) = 4). It should be noted that in
3D-BASIS-ME the inherent damping of the structure is specified in terms of the modal
damping ratios for the superstructure (that is, the part of the structure above the isolation
basemat, as if that part is fixed). A damping ratio of 0.03 was specified for the 27 modes
used in the analysis. Given the type of modeling and constraints used, these 27 modes
fully described the dynamic response.
Pm1 of the output of program 3D-BASIS-ME contains the frequencies and mode
shapes of the superstructure. This output was compared to that obtained from SAP2000
in an analysis of the structure without the isolation system (the SAP2000 model for the
superstructure is described later in this report). Selected results from this comparison are
presented in Table 2-2. The two programs produce nearly identical results. The
SAP2000 model was developed in such a way as to closely approximate the 3D-BASIS-
ME model. This did not expose the extensive features of SAP2000 for modeling a
9

Table 2-2 Comparison of Calculated Periods and Mode Shapes of 8-story
Superstructure (fixed base)
Mode 1
SAP2000 3D-BASIS-ME
Floor Longitudinal Transverse Rotational Longitudinal Transverse Rotational
Component Component Component Component Component Component
8 0.000 0.285 3.40 E-05 0.000 0.285 3.44 E-05
7 0.000 0.268 3.20 E-05 0.000 0.268 3.24 E-05
6 0.000 0.253 2.81 E-05 0.000 0.253 2.84 E-05
5 0.000 0.204 2.44 E-05 0.000 0.204 2.47 E-05
4 0.000 0.165 1.97 E-05 0.000 0.165 1.99 E-05
3 0.000 0.119 1.43 E-05 0.000 0.119 1.44 E-06
2 0.000 0.082 9.74 E-06 0.000 0.082 9.86 E-06
1 0.000 0.041 4.95 E-06 0.000 0.041 5.00 E-06
Period 1.147 sec 1.147 sec
Mode 2
SAP2000 3D-BASIS-ME
8 0.286 0.000 0.000 0.286 0.000 0.000
7 0.269 0.000 0.000 0.269 0.000 0.000
6 0.236 0.000 0.000 0.236 0.000 0.000
5 0.205 0.000 0.000 0.205 0.000 0.000
4 0.166 0.000 0.000 0.166 0.000 0.000
....
0.120 0.000 0.000 0.120 0.000 0.000
.J
2 0.082 0.000 0.000 0.082 0.000 0.000
I 0.042 0.000 0.000 0.042 0.000 0.000
Mode 9
SAP2000 3D-BASIS-ME
8 0.000 -0.223 -2.66 E-05 0.000 -0.223 -2.69 E-05
7 0.000 0.254 3.03 E-05 0.000 0.254 3.06 E-05
6 0.000 0.188 2.24 E-05 0.000 0.188 2.27 E-05
5 0.000 -0.124 -1.48 E-05 0.000 -0.124 -1.49 E-05
4 0.000 -0.259 -3.09 E-05 0.000 -0.259 -3.13 E-05
3 0.000 -0.025 -3.02 E-05 0.000 -0.025 -3.05 E-06
2 0.000 0.177 2.11 E-06 0.000 0.177 2.14 E-06
1 0.000 0.190 2.27 E-06 0.000 0.190 2.30 E-06
10

building. However, it allowed for a direct comparison of the results of the two programs,
and particularly exposed the features ofthe new Nllink element in its Isolatorl property.
Figure 2-2 illustrates the model. The model consists of joints 23 and 55 to 62,
which are interconnected by Nllink elements in the damper property with c specified to
be equal to zero, and with the horizontal stiffness in directions x and y, and the rotational
stiffness specified in accordance with Table 2-1. The floor masses are concentrated at the
eccentric joints 47 to 54, which are constrained to the adjacent joints using the
diaphragm option. Having also specified as active degrees of freedom the UX, UY and
RZ displacements, this model represents a shear-type structure.
The isolation basemat consists of joints 1 to 45 which are constrained to the
basemat mass joint 46 through the body constraint. The 45 isolation bearings are
modeled with Nllink elements, Isolatorl property, which connect joints 1 to 45 to joints
101 to 145. The latter are fixed ground joints. Each of these elements was assigned the
following properties: k2 = k3 = 25.6 kiplin (elastic horizontal stiffness), ratio2 = ratio3
= 0.18868 (post-yielding to elastic stiffness ratio), and yield2 = yield3 = 12.8 kips (yield
force). Moreover, the linear effective stiffness ke was specified as 0.0001 kip/in for the
reasons cited earlier. It should be noted that the linear effective stiffness is calculated to
. be 6.55 kip/in in accordance with the 1994 Uniform Building Code for a design
displacement of 5.8 in. The reason for using a very low value for ke in nonlinear type of
analysis has been explained in Section 2.1 and will become apparent when results of the
analysis are presented.
11

1,101«:" ...-
"
NOTES:
- - -
8'
~54 Joints Constrained as
Nllink Element
Damper Property
(TIP. for all
vertical elements)
11 /
..e::-
16 ...-
A:"
21 /
A:"
" / ~
A:: "...-
26
..e::
62
(61
I
L-60
59
~...-1/Diaphragm (TIP.)
"'-~31
...-~ 1
"'-~2 12' (TIP.)
~1
~o
~ 36 ...-
A:"
41
---
A;:
"
/ 37 "
~42
" ...- ~
~ "
43
• 44
.:...
Y 33 " A;:
____ / 39 " ::.
" ...- 34 ::.- / 45
A;: " / 40
...- 29 " ::.-
/ 7" ~ ...-
2
- ...- 13 " A::
24 -,,::.-"'- 35
'J-. ...- 30
" A : : ...- 19
/ 8 " A:: "
3- A:: / 14 " '- ...- ~o
" ...- 9 ...
- "...- 15
~4 " .. ...- ro
(~~.) "'y 5,105 A
Y"20'
(TIP.)
-- rs,125
'-
/
"" Two Joints at Same Location
with Nllink Element, Isolatorl
Property (TIP.)
1. 'j) JOINTS WITH SPECIFIED MASS AND MASS MOMENT OF INERTIA
2. JOINTS 1 TO 46 CONSTRAINED AS BODY
3. ACTIVE DEGREES OF FREEDOM ARE UX, UY AND RZ FOR JOINTS 46 TO 54
Figure 2-2 Illustration of SAP2000 Model of 8-story Seismic-Isolated Building
Modal damping was specified as 0.03 for each mode. Program SAP2000 utilizes
the specified damping ratios in constructing a proportional damping matrix for the entire
structure including the nonlinear isolation system elements, which are represented by the
specified linear effective stiffnesses. In general, inherent viscous damping in the
structural system (excluding that provided by energy dissipation devices) is accounted for
differently in programs SAP2000 and 3D-BASIS-ME. Specifically,
12

(a) 3D-BASIS-ME utilizes modal reduction, in which the superstructure is represented
by a selected number of modal displacements and not the actual degrees of freedom.
Accordingly, the specified damping ratios for the superstructure are directly used
without construction of a damping matrix.
(b) SAP2000 utilizes a similar approach but for the entire structure, including the degrees
of freedom associated with the isolation system. Moreover, SAP2000 has the option
of using Ritz vectors rather than the eigenvectors.
Accordingly, specification of the same damping ratios does not result in exactly
the same representation of inherent damping in the two programs. However in this
example, the representation is effectively the same due to (a) the small value of the
damping ratio, and (b) the specified very low value of linear effective stiffness for the
isolators.
Analysis in SAP2000 was performed by using all 27 eigenvectors in nonlinear
analysis type.
2.4 Comparison of Results
Figures 2-3 to 2-9 compare the calculated response of the structure by the two
programs. The compared responses include selected bearing force-displacement loops,
floor acceleration histories and histories of story drifts and story relative rotations. The
results of SAP2000 are nearly identical to the results of 3D-BASIS-ME.
It should be noted that in the SAP2000 analysis, an unrealistic value for the linear
effective stifIness (ke = 0.0001 kiplin) was used. When the actual value of ke (= 6.55
kip/in per 1994 UBC) is used, the results generated by SAP2000 do not agree with
13

60 .---------------------------------------------~
W 0
()
0:::
o
u..
CORNER BEARING (JOINTS 1-101)
TRANSVERSE DIRECTION
----- 3D-BASIS-ME
-SAP2000
-60 +-----.-----.-----~----r_----~----~----~--_4
-8 o
DISPLACEMENT (in)
8
60 .---------------------------------------------~
W 0
()
n::
o
u..
LONGITUDINAL DIRECTION
.. -.. 3D-BASIS-ME
-SAP2000
-60 +-----~----~----~----~------~----~----~----~
-8 o
DISPLACEMENT (in)
8
Figure 2-3 Comparison of Calculated Force-Displacement Loops for Corner
Bearing
14

60 ,------------------------------------------------,
W 0
U
~
o
LL
CENTER BEARING (JOINTS 23-123) .
---- 3D-BASIS-ME
-SAP2000
-60 +-----~----~--~----_T----~----~----~--~
-8 o
DISPLACEMENT (in)
8
60 ,---------------------------------------------~
W 0
U
~
o
LL
CENTER BEARING (JOINTS 23-123)
... 3D-BASIS-ME
-SAP2000
-60 +-----~----~----~----~----~----~----~----~
-8 o
DISPLACEMENT (in)
8
Figure 2-4 Comparison of Calculated Force-Displacement Loops for Center
Bearing
15

4.0 ~----------------------------------------------~
c
tL 0.0
0::
o
8th STORY DRIFT
..... 3D-BASIS-ME
-SAP2000
-4.0 +-----.,-----.,.-----,------,---------,----1
o 10 20 30
TIME (sec)
4.0 .,----------------------------,
tL 0.0
0:::
o
8th STORY DRIFT
...... 3D-BASIS-ME
-SAP2000
-4.0 +-------~------~------~--------,--------~----~
o 10 20 30
TIME (sec)
Figure 2-5 Comparison of Calculated 8th Story Drift Histories
16

2.0 ~--------------------------------------------~
tL 0.0
a:
o
3rd STORY DRIFT
. 3D-BASIS-ME
-SAP2000
-2.0 +-------.,....-------.,__------,__------.---------"T"----------j
o 10 20 30
TIME (sec)
2.0 ~----------------------------------------------~
tL 0.0
a:
o
3rd STORY DRIFT
.... 3D-BASIS-ME
-SAP2000
-2.0 +-------~------_r__------.,__------,__------.------~
o 10 20 30
TIME (sec)
Figure 2-6 Comparison of Calculated 3rd Story Drift Histories
17

OJ
--
z
o
....
0.4 ~----------------------------------------------~
8th FLOOR ACCELERATION
~ 0.0
W
-J
W
U
U
«
---- 3D-BASIS-ME
-SAP2000
-0.4 +-------~------~----~~----~------~------~
o 10 20 30
TIME (sec)
0.4 ~----------------------------------------------~
8th FLOOR ACCELERATION
z
o
....
«
0::: 0.0
W
-J
W
U
U
«
. 3D-BASIS-ME
-SAP2000
-0A +-------~-----~----__,;__---___,_----___r----~
o 10 20 30
TIME (sec)
Figure 2-7 Comparison of Calculated 8th Floor Acceleration Histories
18

z
o
I-
0.3 ~----------------------------------------------~
3rd FLOOR ACCELERATION
~ 0.0
W
...J
W
U
U
«
z
o
I-
.... 3D-BASIS-ME
-0.3 +-______~------~------~------~----~~-S-A~P2-0-0-0--~
o 10 20 30
TIME (sec)
0.3 ~----------------------------------------------~
3rd FLOOR ACCELERATION
~ 0.0
W
...J
W
U
U
«
. 3D-BASIS-ME
-SAP2000
-0.3 -!-------,-----.,-----,------,------,--------1
o 10 20 30
TIME (sec)
Figure 2-8 Comparison of Calculated 3rd Floor Acceleration Histories
19

0.001 -,--------------------------,
8th STORY ROTATiON
z
o 0.000
I-
~
o
0::
z
...... 3D-BASiS-ME
-SAP2000
-0.001 +------,.------r------r------,------,-------i
o 10 20 30
TIME (sec)
0.0004 . , - - - - - - - - - - - - - - - - - - - - - - - ,
3rd STORY ROTATiON
o 0.0000
I-
«
I-
o
0::
.' 3D-BASiS-ME
-SAP2000
-0.0004 +-----.----.--~-___r_---_r_--___r_------1
o 10 20 30
TIME (sec)
Figure 2-9 Comparison of Calculated Relative Story Rotation Histories
20

those of 3D-BASIS-ME. This is illustrated in Figures 2-10 and 2-11, which compare the
calculated force-displacement loops of two bearings. The SAP2000 solution
underestimates the bearing displacements, though the underestimation may not be of
practical significance in this example. A likely explanation for this small discrepancy in
the results of SAP2000 is that the modes for the actual value of the linear effective
stiffness do not adequately represent the behavior of the analyzed system. It should be
noted that the analytical prediction did not improve when Ritz vectors were used instead
of mode shapes.
21

60 ~--------------------------------------------~
w 0
U
CC
o
LL
... 3D-BASIS-ME
- SAP2000 (Ke=6.55 kiplin)
-60 +-----~----~----~----~----~----~----~----~
-8 o
DISPLACEMENT (in)
8
60 ~--------------------------------------------~
w 0
U
CC
o
LL
... 3D-BASIS-ME
- SAP2000 (Ke=6.55 kip/in)
-60 +-----~----~----~----~----~----._----._--~
-8 o
DISPLACEMENT (in)
8
Figure 2-10 Comparison of Calculated Force-Displacement Loops for Corner
Bearing when the Actual Value of ke is Used
22

60~--------------------------------------------~
w 0
()
0:::
o
LL
.. 3D-BASIS-ME
- SAP2000 (Ke=6.55 kip/in)
-60+-----~----~--~----_T----~----~----~--~
-8 o
DISPLACEMENT (in)
8
60 ~---------------------------------------------.
,-...
(/J
Q.
w 0
()
0:::
o
LL
..... 3D-BASiS-ME
- SAP2000 (Ke=6.55 kip/in)
-60 +-----~----~----~----r_----~----~----~--~
-8 o
DISPLACEMENT (in)
8
Figure 2-11 Comparison of Calculated Force-Displacement Loops for Center
Bearing when the Actual Value of ke is Used
23

SECTION 3
ANALYSIS OF A LIQUID STORAGE TANK
WITH THE FRICTION PENDULUM ISOLATION SYSTEM
3.1 Introduction
The system analyzed in this section is a seismically isolated liquid storage tanle It
IS described and analyzed in the manual for 3D-BASIS-ME (Tsopelas et aI., 1994).
Neither 3D-BASIS-ME nor SAP2000 have the capability of explicitly modeling the
dynamic behavior of a liquid storage tank, that is, to directly model fluid-structure
interaction. However, both programs are capable of analyzing mechanical models of the
liquid-tank system such as that described by Haroun and Housner (1981). In this
approach, mathematical analysis is employed in order to arrive at a representation of the
system consisting of an assemblage of oscillators, each one of which simulates a specific
effect, such as sloshing of the liquid, deformation of the liquid-tanle system and impulsive
response. The calculated response of these oscillators is then used to evaluate important
response quantities for design, such as base shear and bending moment induced by the
hydrodynamic wall pressure, and vertical displacement ofthe liquid.
Program 3D-BASIS-ME has the capability of modeling multiple structural
systems connected to a rigid basemat, above the seismic isolators. The program also has
the options of including overturning moment effects through the use of an externally
supplied function, and of vertical ground acceleration. Since vertical degrees-of-freedom
are excluded in program 3D-BASIS-ME, the specified vertical ground acceleration is
used to directly modify the instantaneous vertical load on the bearings. In most cases, for
25

example building structures, this is sufficient. However, liquid storage tanks are
vertically flexible (Le., axisymmetric mode of vibration), which typically results in
additional axial load on the bearings. In this case, a modified vertical acceleration history
must be specified, which is calculated by an independent analysis of the system in the
vertical direction.
3D-BASIS-ME permits modeling of the horizontal dynamic response of
seismically isolated liquid storage tanks, but considerable a priori knowledge of the
behavior of such systems is required. The main feature of the program is the calculation
of the instantaneous vertical load on the bearings and the incorporation of this effect on
the instantaneous stiffness and friction force in the Friction Pendulum bearings.
Program SAP2000 has a three-dimensional formulation which, unlike program
3D-BASIS-ME, allows for direct consideration of the vertical ground acceleration and
overturning moment effects. This option has not been fully exercised in this example.
Rather, the changes in axial load due to the overturning moment have been ignored and
vertical oscillations have been effectively suppressed, with the only maintained feature in
the program being the effect of the vertical ground acceleration. That is, the model in
SAP2000 has been reduced to one that can be directly modeled by 3D-BASIS-ME so that
results from the two programs could be compared. Thus, this example primarily
represents a verification test for the Isolator2 property of the Nllink element of SAP2000
within a rather complex structural system with a small number of degrees of freedom.
Certain difficulties were encountered in the modeling of the mechanical
representation of the liquid-tank system, which will be described later in this section.
When these difficulties were effectively bypassed, SAP2000 produced results that were
26

nearly identical to those of program 3D-BASIS-ME.
3.2 Description of Analyzed Liquid Storage Tank
The liquid storage tank is illustrated in Figure 3-1, whereas Figure 3-2 shows the
layout of the isolation bearings. Material unit weights are: for water 62.75 Ib/ft3
, for steel
490 lb/fe and for concrete 150 Ib/ft3. The weights are: water (for full tank) 28387.4 kips,
steel tank 646.5 kips, steel roof 477.3 kips and concrete basemat 2629.8 kips with a total
isolated weight of32141 kips.
The liquid storage tank is represented by the mechanical system illustrated in
Figure 3-3 on the basis of the theory of Haroun and Housner (1981). In this
representation only the fundamental tank-fluid and liquid sloshing modes of vibration are
considered, with the remaining modes considered to be rigid. It should be noted that each
of the oscillators shown in Figure 3-3 has three degrees of freedom: two horizontal
translational (UX and UY) with the properties indicated in the figure, and a rotational
about the vertical axis of which the associated rotational stiffness and mass moment of
inertia are arbitrarily specified to be very small and very large, respectively.
The isolation system consists of 52 identical Friction Pendulum bearings with a
radius of curvature equal to 82.4 in. It is assumed that all 52 bearings are subjected to the
same bearing pressure under static conditions. Even so, the frictional properties of the
bearings cannot be identical due to variations in the vertical load that results from the
vertical ground motion and the overturning moment. The frictional properties were
assumed to be independent of the instantaneous pressure, with the coefficient of sliding
friction described by
27

2.0 ft
1
T
.
9 ft
17 ft
17 ft
17 ft
R=60.0 ft
-I
1 in.
STEEL ROOF
WATER
H=40.0 ft
RiC BASEMAT
1
T
RIC PEDESTAL
.1
WITH BEARING
122.0 ft
Figure 3-1 Geometry of Isolated Water Tank
Symm.
17 rt I 17 rt 117 rt rrtl
I" ... I.. •.••.
ISOLATION
BEARING
Figure 3-2 Configuration of Isolation System
28
STEEL TANK
1 in.
1.5 ft
Symm.

SLOSHING FLUID
WS =16317 kips
T S =6.89 sees
fJ S =0.005
22.2 fl
RIGID CONVECTIVE
FLUID
WR =1194.2 kips
RIGID/
16.2 fl
RIGID BASEMA
TANK-FLUID
1f F = 12000 kips
T F =0.162 sees
fJ F =0.02
16.04 fl
WB =2629.8 kips
Figure 3-3 Mathematical Model of Liquid Storage Tank
f.l =fmax - (fmax - fmin ) exp (-av) (3-1)
where v = amplitude of instantaneous sliding velocity vector, a = 0.8 sec/in, £nax = 0.045
and £11in = 0.03.
3.3 Modeling of Liquid Storage Tank in 3D-BASIS-ME
The model in 3D-BASIS-ME has been presented in Tsopelas et al. (1994). In this
model the oscillators in Figure 3-3 are represented as single story, shear-type structures
connected to the center of mass of the basemat which is located at its geometric center.
That is, no eccentricities are considered. It should be noted that in the analysis of
Tsopelas et al. (1994) an eccentricity of one-percent of the tank's plan dimension was
considered.
The 52 bearings are represented by clusters of bearings as shown in Figures 3-4
and 3-5. The central cluster (No.5) consists of 26 bearings, whereas the remaining
29

bearings are equally divided to four identical clusters. The clusters are located at specific
locations so that the rotational stiffness of the five clusters is identical to that of the 52
bearings (on the basis of the horizontal stiffness, excluding friction).
The model analyzed herein is identical to that analyzed by Tsopelas et al. (1994),
except that eccentricities are neglected, and the overturning moment effects and the
dependency of the coefficient of friction on the instantaneous bearing pressure are not
considered. Each cluster of bearings are assigned the following properties: radius 82.4 in,
a = 0.8 sec/in, f = 0.045, f . = 0.03 and gravity load of either 16070 kips (No.5) or
max mill
4017 kips (No.1 to 4). Moreover, a value for the yield displacement equal to 0.02 in. is
used, based on the mechanical properties ofthe sliding interface.
The seismic excitation consists of the Pacoima Dam record of the 1971 San
Fernando earthquake. Component Sl6E (peak acceleration of 1.17g) is applied in the X
direction and component S74W (peak acceleration of 1.08g) is applied in the Y direction.
The vertical component has a peak acceleration of 0.71 g, resulting in a maximum ±71-
percent variation in the axial load on the bearings (for the vertically rigid model). The
excitation is a severe earthquake motion with high velocity, near-fault characteristics.
3.4 Modeling of Liquid Storage Tanks in SAP2000
Modeling of the tank in SAP2000 was impeded by:
(a) The requirement to model the system in a shear-type representation, that is, to
exclude the vertical displacement degree of freedom. In general, this degree of
freedom should be included. The use of Nllink element, Isolator2 property for
representing the Friction Pendulum bearings requires that this degree of freedom is
30

SLOSHING
MODE
U
z Uz
1
1 Uy
1 /
FLUID-TANK
MODE
t Uy
1 /
I = 1700000 K-in-s
2
~ -:;-.12 K/in
W = 16317KilP/ Ux
I = 1700000 K-in-~ - - x
W =12000 KilS
/ U
Ky= Kx
KR = 3659 K-in
~ = 0.005 (ALL MODES
7
Kx =46716.9 K/in
Ky = Kx
KR =6618227.5 K-in
~ =0.02 (ALL MODES)
BASEMAT
W =3824 Kips
I = 427528 K-in-~
/4 ~/ 2
820.56 in
(TYP.)
. I
5 1/
--~-
/ I
3
- ___ X
' - CLUSTER OF
6.5 BEARINGS
CLUSTER OF
26 BEARINGS
Figure 3-4 Model of Liquid Storage Tank in 3D-BASIS-ME
maintained. It was effectively suppressed by using damping elements.
(b) The requirement to specify the damping ratio for each part of the superstructure,
which is not possible to accurately accomplish through specification of global
damping. For this case of simple one-story superstructures, the problem was
circumvented by utilizing damping elements.
31

820.56 in
•
1
820.56 in
820.56 in
BEARING
CLUSTER
820.56 in
..I
Figure 3-5 Location of Clusters of Bearings in 3D-BASIS-ME
The SAP2000 model consisted of the following elements:
(a) Nllink, plastic1 property elements to represent each of the two superstructures.
Linear behavior of these elements was ensured by specifying a value of unity for
ratio and a large value for yield (the yield force). The stiffnesses for the shear
deformations and the rotational degree of freedom (which is linear) were specified in
accordance with Figure 3-4. The vertical displacement degree of freedom was
maintained but effectively suppressed by specifying a small vertical mass and a
32

related vertical stiffness that resulted in a large vertical frequency (=1000 rad/sec).
The linear effective stiffness ke for each of the nonlinear elements was specified to
be very small (ke = 0.0001 kip/in).
(b) Nllink, damper property elements to represent damping in the two superstructures.
The nonlinear configuration of this element was used with cexp being unity (default
value). A very small value for the linear effective stiffness was used (= 0.0001
kip/in) and zero value (default) for the linear effective damping was used.
(c) Nllink, Isolator2 property elements for the Friction Pendulum bearings. Each of the
five clusters shown in Figure 3-5 was represented by an element with radius = 82.4
in, rate = 0.8 seclin, slow = 0.03, fast = 0.045, elastic stiffness ke =21092 kiplin or
84370 kiplin and linear effective stiffness ke = 0.0001 kip/in. The elastic stiffness
was determined from
K = fmillW
y
(3-2)
where W = gravity load on the bearing cluster, f. = mInImUm value of the
mill
coefficient of friction (= 0.03) and Y = yield displacement (= 0.02 in). The value of
the linear effective stiffness was specified very small based on experience gained in
the analysis ofthe 8-story isolated structure (see Section 2).
The gravity load on the bearings is typically generated in SAP2000 from loads
applied to the superstructure. In this case the gravity load was specified as
concentrated force load directly on the bearings. These forces were applied quasi-
statically, that is, dynamically over a long time duration. The program's built-in ramp
function was used with a duration of 10 sec (5 sec build-up time and 5 sec constant
load) and with a large modal damping ratio (= 0.99) to prevent oscillations.
33

(d) NlIink, damper property for suppressing vertical oscillations in the elements
representing the clusters of Friction Pendulum bearings. A large value of stiffness k
was used to simulate pure damping behavior. However, the linear effective stiffness
ke was again specified very small to avoid errors. The element was used in its
nonlinear option but with cexp = 1. When the linear option was used the element
was null (that is, it produced no effect).
An appropriate value for the damping coefficient c was determined by trial and
error. The values of this coefficient, of the axial stiffness of the Friction Pendulum
bearings and of the step for time-history analysis were varied so that the calculated axial
force on the Friction Pendulum bearings was essentially equal to the gravity load
multiplied by ul' /g , where u,'= vertical ground acceleration.
That is, vertical oscillation at isolation system level was effectively eliminated
and the overturning moment effects were suppressed. The attempt to eliminate vertical
oscillations and overturning moment effects was made so that the results could be
compared to those of program 3D-BASIS-ME. In general, these effects should be
accounted for in the analysis.
The selection of elements used in the modeling of the liquid storage tank is not
unique; other combinations of elements or options could have been utilized. A number of
these options were investigated and found unsuccessful. Specifically:
(a) When the linear option for the Nllink, damper property elements was used, the
analysis could not be performed when ke was specified to have a large value, whereas
the element was null when the value of ke was specified to be very small.
(b) When the Nllink, damper property element was used instead of the plastic1 property
34

for representing the stiffness of the superstructures (as it was done in the 8-story
building example), the analysis could not be performed. Only when the element was
used in its nonlinear option with very small ke analysis could be performed.
However, the results were obviously erroneous.
3.5 Comparison of Results
Figures 3-6 and 3-7 compare the calculated force-displacement loops of the
central and for one of the exterior clusters of bearings. The results of the two programs
are nearly identical.
Figures 3-8 to 3-11 compare the calculated histories of displacements and
accelerations of the sloshing fluid and the fluid-tank mode. Some insignificant
differences are observed in the results for the fluid-tank mode. It should be noted that
this mode is substantially stiffer (period of 0.162 sec) than either the sloshing fluid mode
or the isolation system. These differences are due to the modeling used in the two
programs and in the numerical integration algorithms.
Of particular interest is the calculated acceleration history for the fluid-tank mode.
The peak acceleration value is used in the calculation of the overturning moment and
shear force for the design of the tank. The two programs predict nearly identical peak
values (see Figure 3-11). Moreover, the calculated acceleration histories may be used to
construct response spectra for pipework analysis and design (that is, construction of
"floor" response spectra). The calculated acceleration histories have different frequency
contents, with the SAP2000 results exhibiting slightly higher frequency content. Such
differences would inevitably result in differences in the "floor" spectra, which may be
35

4000~----------------------------------------~
X-DIRECTION
w 0--
o
0::
o
LL
---- -- 3D-BASIS-ME
-SAP2000
-4000+-----~------~----~------~------~----~
-15 o
DISPLACEMENT (in)
15
4000~-----------------------------------------.
----
C/)
Cl...
w 0
o
0:::
o
LL
Y-DIRECTION
----- - 3D-BASIS-ME
-SAP2000
-4000 +-------~----~------~------~------~----~
-15 o
DISPLACEMENT (in)
15
Figure 3-6 Comparison of Calculated Force-Displacement Loops for Central
Cluster of Bearings (No.5)
36

1000.-----------------------------------------~
w 0
()
0:::
o
LL
X-DIRECTION
- _. - 3DBASIS-ME
-SAP2000
-1000+-----~------~----~------~------~----~
-15 o
DISPLACEMENT (in)
15
1000.-----------------------------------------~
----
C/)
Q.
:.s2
'--"
w 0
()
0:::
o
LL
Y-DIRECTION
..... 3D-BASIS-ME
-SAP2000
-1000 ~------------------------------------~----~
-15 o
DISPLACEMENT (in)
15
Figure 3-7 Comparison of Calculated Force-Displacement Loops for Exterior
Cluster of Bearings (No.1)
37

..--..
c
I-
Z
W
50 ~--------------------------------------------~
X-DIRECTION
..... 3D-BASIS-ME
-SAP2000
-50 +---~----~--~--~----~--~--~----~---r--~
o 10
TIME (sec)
20
50 ~----------------------------------------------~
Y-DIRECTION
~ 0 --l--~---:--"
U
«
.....I
D-
C/)
o
..... 3D-BASIS-ME
-SAP2000
-50 +---~----~--~----~--~----~--~----~--~----~
o 10
TIME (sec)
Figure 3-8 Comparison of Calculated Displacements of Sloshing Fluid
38
20

c
I-
Z
W
0.15 . , - - - - - - - - - - - - - - - - - - - - - -
X-DIRECTION
~
W 0.00
u
::s
(L
(f)
o
..... 3D-BASIS-ME
-SAP2000
-0.15 +----,---,----,-------,.--.,----,-----,---,----,----1
-
c
I-
Z
W
o 10
TIME (sec)
20
0.15 . , - - - - - - - - - - - - - - - - - - - - - - - - ,
Y-DIRECTION
~
W 0.00
u
«
..J
(L
(f)
o
..... 3D-BASIS-ME
-SAP2000
-0. 15 -+----r------.--..,----.,------r--.----~-__r_--r__-
o 10
TIME (sec)
Figure 3-9 Comparison of Calculated Displacements of Fluid-Tank Mode
39
20

---..
0>
.........
z
o
I-
0.1 ,-------------------------------------------~
X-DIRECTION
~ 0.0 -+---~
W
-l
W
o
o
~
-.. 3D-BASIS-ME
-0.1 +-__~----,---~----,---~----,_--~--~~~S-A-P-2-0~OO--~
---..
0>
.........
z
o
I-
o 10
TIME (sec)
20
0.1 .---------------------------------------------~
Y-DIRECTION
~ 0.0 "'---':""-.J
W
.....J
W
U
U
~
...... 3D-BASIS-ME
-SAP2000
-0.1 +---~--~----~--~--~--~----,_--~--~--~
o 10
TIME (sec)
Figure 3-10 Comparison of Calculated Accelerations of Sloshing Fluid
40
20

0.6 .-------------------------------------------------~
X-DIRECTION
z
o
I-
«
a:: 0.0
w
--.I
W
o
o
«
.... 3D-BASIS-ME (peak=0.495g)
- SAP2000 (peak=0.495g)
-0.6 -t-----,-----,---r---..,----,-----.--.,----r-----r----i
..-...
0)
---
o 10
TIME (sec)
20
0.6 ~------------------------------------------------~
Y-DIRECTION
z
o
I-
«
a:: 0.0
w
--.I
W
o
o
«
..... 3D-BASIS-ME (peak=O.340g)
- SAP2000 (peak=O.344g)
-0.6 +----,------,,----,------,------,,----,------,---,---..,-----j
o 10
TIME (sec)
Figure 3-11 Comparison of Calculated Accelerations of Fluid-Tank Mode
41
20

substantial. Experience has shown that the high frequency end of such spectra is
unrealistic and typically traceable to some seemingly insignificant parameter in the
model, such as the "yield displacement" or the elastic shear stiffness, in programs 3D-
BASIS-ME and SAP2000, respectively. A notable example of such experience has been
the analysis of two LNG storage tanks described by Constantinou (1998b). It is
appropriate to state at this time that there is no analysis program that can produce reliable
results for the high frequency end of "floor" response spectra.
42

SECTION 4
ANALYSIS OF EXPERIMENTAL RESPONSE OF A 7-STORY BUILDING
MODEL WITH FRICTION PENDULUM ISOLATION SYSTEM
4.1 Introduction
The structure analyzed in this section is a 7-story seismically isolated building
model that was tested on a shake table by AI-Hussaini et al. (1994). This model was
tested in a variety of configurations, one of which involved the isolators placed directly
below each column of the moment frame, without an isolation basemat or diaphragm.
Due to the large height-to-width ratio of the structure, large overturning moments
developed in the experimental program which led to bearing uplift.
In this example, the modeling capabilities of SAP2000 are fully explored. Unlike
the previous two examples in Sections 2 and 3, in which a specific behavior of the
analyzed systems was sought (e.g., shear type representation, exclusion of overturning
moment effects, etc.), the structural system is modeled in its entirety.
4.2 Description of Tested Structure
Figure 4-1 shows elevations and a plan view of the 7-story model in one of the
tested configurations. This configuration is termed MFUIS in the report of AI-Hussaini
et al. (1994). This structure is a quarter length scale model of a slice of a building along
its longitudinal direction. Connections of beams to columns are rigid, either welded or
43

S 3XS.7
S 4X9.S
S
I"
3 @ 4 ft = 12 ft
SHAKE TABLE
TESTING DIRECTION
S
co
D
KIPS TYP.
EVERY BAY
AND FLOOR
FPS BEARING
N E
TRANSVERSE VIEW
FPS BEARING
Q Q
N
C1 C2 C3
D D D
PLAN VIEW OF ISOLATION LEVEL
Figure 4-1 Elevations and Plan View of Tested Structure
-
N
II
.-
-
w
bolted depending on the location. The braces in the transverse direction are bolted with a
single bolt at each end, that is, they are effectively pin-connected.
Concrete block and steel plate weights were installed at each floor and bay of the
model for an estimated total weight of 47.5 kips. The distribution of this weight was
estimated to be 7.6 kips at the first floor, 6.7 kips at the second to sixth floors, and 6.5
44

kips at the top floor. This weight includes the added block and steel plate weights and the
tributary column, beam and brace weights.
The isolation system consisted of eight Friction Pendulum bearings, each with a
radius of curvature equal to 9.75 in, directly connected to the square tube columns of the
first story. Each bearing had a displacement capacity of 2 in. The contact area at the
sliding interface of the eight bearings was such that the bearing pressure was about 18 ksi
under the gravity load and on the basis of the assumption that load is distributed in
accordance with the tributary area of each column (that is, exterior bearings carry 3.96
kips each, and interior bearings carry 7.92 kips each).
The exact distribution of gravity load on the bearings was not known due to the
method used to erect the model on the shake table. In this method the bearings are first
installed and leveled on the shake table, and then the model, fully loaded with weights
and appropriately braced for lifting, is placed on top of the bearings. The distribution of
load on the bearings is not exactly the one obtained when the structure is built from the
bottom up, as in regular construction. Rather, the distribution deviates as a result of
misalignments in the model.
The coefficient of sliding friction of individual bearings was not determined.
Rather, the frictional properties were obtained for the entire assembly of the eight
bearings. The coefficient of friction could be described by (3-1) with fll1ax = 0.06, t~nin =
0.04 and a = 1.09 seclin. These properties are representative of the bearings for the
average conditions of bearing pressure, that is, about 18 ksi. Given that in some of the
tests the bearings experienced significant variations in bearing pressure, the analysis
should have accounted for the effects of instantaneous pressure on the frictional
45

properties. This capability is not available in SAP2000, but it does not appear to have a
significant effect on the calculated response.
Testing of this model was conducted with several earthquake motions applied in
the longitudinal direction. Results presented herein and compared to the analysis results
are for the SOOE component of the 1940 EI Centro earthquake record scaled up to a peak
acceleration of 0.57 g (that is, twice the recorded level). In the testing and analysis, the
time scale of the record was compressed by a factor of two in order to satisfy the
similitude requirements.
4. 3 Modeling in SAP2000
The structure was modeled as a two-dimensional frame with the geometric
properties of sections doubled to represent the full model. Figure 4-2 illustrates the
model. Frame elements were used together with specified offset and rigid-end factor
values. The four joints on each of the seven floors were constrained using the
diaphragm option. Masses were lumped at the joints. The gravity load was directly
developed at the top joint of bearing elements and applied dynamically using a ramp of 5
sec build-up time, followed by a 5 sec constant load interval, and a damping ratio of 0.99
in order to prevent oscillations. The applied gravity loads were 7.92 kips and 15.83 kips
for the exterior and interior bearings, respectively. They were directly applied at the
bearing top joints. In reality, the gravity loads on the bearings may have been different
for the reasons explained in Section 4.2.
46

z
Mass Equal to 1/3 of
4' (TYPo) /1 Floor Mass (Typo all floors)
I • .. I
29 30 31 32
25
3' (TYP,) [
21
End Offset ~
(Typo all joints) 17
26
22
18
- - - -
13 14
~-- - - - -
9 10
5 6
.. 2~
• I
1
- - - -
- -~~~-
V15.83 '''-.,j
t
27
23
19
- - -
15
- - - -
11
7
"3
~ Mass Equal to 1/6 of
Floor Mass (UX, UZ dof)
(Typ. all floors)
28
24
2o
I--
Joints Constrained
6~ ....---- as Diaphragm
1 ) (Typo all floors)
- -
12
8
7.92 k
~
Weight on Bearings,
r Applied Dynamically
lover 10 sec Duration
/e33 e34 e35 e 36 ~ X
Axial Nllink Element,
Damper Property
(Typ.) "
Two Joints at Same
Location with
Nllink Element,
Isolator 2 Property
(Typ.)
Figure 4-2 Model of 7-story Isolated Structure in SAP2000
47

The four Friction Pendulum bearings were modeled using the Nllink element,
Isolator2 property with the following parameters for the shear deformation degree of
freedom:
(a) Elastic stiffness k = 31.67 kip/in (exterior) and 63.33 kip/in (interior). This stiffness
was calculated on the basis of (3-2) with fmin= 0.04, W = gravity load (7.92 kips or
15.83 kips) and Y = 0.01 in.
(b) Linear effective stiffness ke = 0.0001 kip/in. This value was chosen on the basis of
observations made in the tirst presented example (see Section 2.1). However, nearly
identical results were obtained when realistic values of the linear effective stiffness
were used. Specifically, values of ke equal to 2.1 kip/in and 1.05 kip/in, for interior
and exterior bearings respectively, were used.
(c) Radius = 9.75 in, fast = 0.06, slow = 0.04, rate = 1.09 sec/in.
Moreover, the stiffness for the linear rotational degree of freedom was specified as ke =
10,000 kip-infrad, and the axial stiffness kJ was specified to be 20,000 kip/in. The latter
figure was based on calculations of the stiffness using the actual geometry of the
bearings.
The axial (vertical) degree of freedom of the Nllink element, Isolator2 property
is nonlinear. Accordingly, the axial linear effective stiffness ke needs to be specified.
An appropriate value is equal to kl' that is 20,000 kip/in. When such a value was used,
execution of the program was aborted. When lower values were used, analysis was
performed but the results were erroneous. Only when ke was specified to be very small,
has the analysis executed without problems and with good results.
48

Damping elements were added at the bearing locations in the vertical direction
using the Nllink element, damper property with stiffness k = 10,000 kiplin and damping
coefficient c = 5 kip-sec/in (to represent a pure linear viscous element). The value of the
damping coefficient was selected to provide a damping ratio of 0.10 on the basis of a
weight of 47.5 kips and total vertical bearing stiffness of 80,000 kip/in (4k,). That is,
Of interest is to explain the need for usmg vertical damping elements at the
Friction Pendulum bearing locations. In general, such elements appear unnecessary and
are not used in an example provided in the verification manual of SAP2000. When such
elements were excluded, erroneous response was calculated. Specifically, the calculated
bearing forces exhibited significant fluctuations. Some improvement was noticed when
Ritz vectors were used rather than mode shapes. This issue will be revisited when
analysis results are presented.
Global damping in the model was specified in terms of damping ratios for the
eleven modes retained in the analysis. These values were obtained from experiments as
described in AI-Hussaini et al. (1994) for the seven modes related to primarily horizontal
movement, whereas the remaining modes (associated with primarily vertical movement)
were assigned similar values.
At first, eigenvalue analyses were performed on the model with the elements
representing the bearings removed and replaced by pins and rotational springs of stiffness
equal to 10,000 kip-in/rad. This approximately represented the structure as tested in its
non-isolated configuration. Parameter rigid-end factor was varied with a value of 0.45
finally resulting in mode shapes and periods that sufficiently approximated the
49

experimental values. Table 4-1 compares the experimental periods and mode shapes
(only six were identified; all associated with horizontal floor displacement degrees of
ti-eedom) with the ones calculated by SAP2000. This indicates that SAP2000 sufficiently
modeled the behavior of test structure in its non-isolated configuration.
4.4 Analysis Results and Comparison to Experiment
Figure 4-3 presents experimental and analytical results on the base shear-
isolation-system displacement loops and the displacement history of isolators and the first
story columns. The isolation system displacement is the displacement of the first floor
with respect to the ground (that is, the bearing displacement plus the drift in the column).
The base shear is the sum of the shear forces in the first story columns. In the experiment
they were directly measured by strain gage load cells in each column. Moreover, the
experimental displacement is the average of the recorded displacements at the two
columns of the first floor level (east and west locations).
Figures 4-4 and 4-5 compare experimental and analytical histories of selected
story drift, story shear and floor acceleration. The second story shear was determined
from the recorded acceleration histories and the known distribution of mass. The third
story drift was directly measured by displacement transducers placed on the east-side
columns. The seventh floor acceleration was calculated as the average of recorded
accelerations at the seventh floor on the east and west sides of the model.
These figures demonstrate that SAP2000 predicts well the experimental global
response of the isolated structure, except for the prediction of higher shear force in the
second story. It is possible that in this case the experimental shear force contains some
50

Table 4-1 Experimental and Analytical Modal Properties of Non-isolated 7-story
Model
PERIOD (sec)
MODE EXPERIMENTAL SAP2000
1 0.455 0.458
2 0.139 0.151
,..,
0.081 0.088
.J
4 0.052 0.061
5 0.041 0.045
6 Not identified (vertical) 0.039
7 0.034 0.036
EXPERIMENTAL MODE SHAPES (associated with horizontal displacements
FLOOR MODEl MODE 2 MODE 3 MODE 4 MODES MODE 7
7 1 0.918 0.812 0.704 0.471 0.363
6 0.914 0.467 -0.197 -0.967 -0.896 -0.700
5 0.822 -0.193 -1 -0.742 0.346 1
4 0.675 -0.798 -0.513 1 0.493 -0.755
,..,
0.479 -1 0.708 0.653 -0.948 0.033
.J
2 0.289 -0.755 0.844 -0.932 0.542 0.538
1 0.138 -0.373 0.473 -0.837 1 -0.868
SAP2000 MODE SHAPES
FLOOR MODEl MODE 2 MODE 3 MODE 4 MODES MODE 7
7 1 0.982 0.978 1.506 0.655 0.410
6 0.941 0.538 -0.081 -1.280 -1.094 -0.986
5 0.837 -0.110 -1 -1.605 0.123 1
4 0.692 -0.707 -0.857 1 1.022 -0.376
,..,
0.514 -1 0.196 1.793 -0.771 -0.484
.J
2 0.315 -0.875 1.053 -0.668 -0.535 1.046
1 0.138 -0.470 0.890 -1.893 1 -0.786
error since it was not directly measured but rather obtained by computation on the basis
of the experimental accelerations and the imprecisely known distribution of mass.
51

l-
I
(9
W
S
0:::
«
w
I
(f)
w
(f)
«
ill
..--..
c:
c
I-
Z
w
2
w
u
«
-.J
0...
(J)
0
0.3,-------------------------------------------~
ISOLATION SYSTEM WEIGHT=47.5 kips
o
r" '" EXPERIMENTAL
-SAP2000
-0.3 +---~----~--~----~--_r----~--~----~--~--~
-2.5 o 2.5
ISOLATION SYSTEM DISPLACEMENT (in)
2.5 ~----------------------------------------------~
0
ISOLATION SYSTEM
:1
.... EXPERIMENTAL
-SAP2000
-2.5 +-------r------,-----,..-------.------r----,-------r------.-----,-----i
o 10
TIME (sec)
20
Figure 4-3 Comparison of Analytical and Experimental Results on the Base Shear-
Displacement Loop and Isolation System Displacement History
52

l-
I
(j
W
I
0.6 . - - - - - - - - - - - - - - - - - - - - - - - - - - ,
3rd STORY DRI FT HEIGHT =36 in
C= 0 ~~"""'"
0::
o
>-
0::
o
I-
(f)
"0
....
C")
l-
I
(j
W
S
--
0::
<{
W
I
(f)
>-
0::
o
I-
(f)
"0
C
N
..... EXPERIMENTAL
-SAP2000
~;
-0.6 +-----,--,...---.-------,--,...---.--------,--....---.----1
o 10
TIME (sec)
20
0.4 .-----------------------------------------------~
2nd STORY SHEAR WEIGHT =47.5 kips
... EXPERIMENTAL
-SAP2000
-0.4 -+----.-----,,---,-----.-----,,---,------,--,---,-------j
o 10
TIME (sec)
20
Figure 4-4 Comparison of Analytical and Experimental Results on Selected
Histories of Story Drift and Story Shear Force
53

z
o
I-
«
0::
w
-.J
W
U
U
«
0.8 - r - - - - - - - - - - - - - - - - - - - - - - - - - - - ,
..... EXPERIMENTAL (peak=O.60g)
- SAP2000 (peak=O.63g)
-0.8 +----,------.---r----,------,r----,-------.---.,-----,-------1
o 10
TIME (sec)
20
Figure 4-5 Comparison of Analytical and Experimental Results on the 7th Floor
Acceleration
Figure 4-6 presents experimental and analytical force-displacements for one
exterior (C4) and one interior bearing (C5). These two bearings (see Figure 4-1) were
instrumented to measure the bearing displacements. Since the analysis was performed
with a planar representation of the structure, the calculated bearing shear forces were
divided by factor of two to obtain the force in a single bearing. The exterior bearing
underwent significant variation in the axial load and experienced uplift. The SAP2000
program does predict this behavior with good accuracy given the uncertainty in the
gravity load on the bearing. It should be noted that the gravity loads on the bearings were
not exactly known and they could very well have been different than assumed in the
analysis.
54

ill
()
4 .-------------------------------------------------~
INTERIOR BEARING
(JOINTS 2-34, BEARING C5)
~O
LL
0::
«
ill
I
(f)
...... EXPERIMENTAL
-SAP2000
-4 +----,----.----.----.-----,---_.----,_--_,----._--~
----
CIl
Cl..
ill
()
-2.5 o 2.5
BEARING DISPLACEMENT (in)
4 .-------------------------------------------------~
EXTERIOR BEARING
(JOINTS 1-33, BEARING C4)
~O
LL
0::
«
ill
I
(j)
...... EXPERIMENTAL
-SAP2000
-4 +----,----~--_.----._----,_--_.----,_--_,----._--~
-2.5 o 2.5
Figure 4-6 Comparison of Analytical and Experimental Shear Force-Bearing
Displacement Loops
55

The analytical results presented in Figures 4-3 to 4-6 were obtained with a
SAP2000 model of which the important features are: (a) use of a very low value for the
linear effective stiffness ke related to the shear degrees of freedom of element Isolator2,
(b) use of vertical damping elements at the isolator locations, and (c) use of eleven
eigenvectors.
Analyses were also performed using other combinations of parameters and
different modeling. Specifically, analyses were performed without the vertical damping
elements at the isolator locations; the base shear force-displacement loop are presented in
Figure 4-7. Analyses were performed with either a) eleven eigenvectors, or b) with 26
Ritz vectors, and with either a) linear effective stiffness in the shear degrees of freedom
of the Isolator2 elements being very low, or b) realistic values (2.1 kip/in for the interior
and l.05 kip/in for the exterior bearings). The results show large fluctuations in the
calculated force. The prediction improves with the use of larger number of Ritz vectors
(maximum possible was 26 for the model in SAP2000) but the analytical prediction is
poor. No improvements were noticed when a larger number of eigenvectors was used. It
is likely that with more refined modeling (e.g., without constraints) and a sufficiently
large number of properly constructed Ritz vectors, response of acceptable accuracy could
be obtained without the use of vertical damping elements.
Figure 4-8 presents the experimental and the calculated loops of base shear-
isolation system displacement and of shear force-bearing displacement for the exterior
bearing. The analytical response is obtained with a model having vertical damping
elements, eleven eigenvectors and realistic values for the linear effective stiffiness for the
shear degrees of freedom of the Isolator2 elements. The results of these figures should
56

be compared to those of Figures 4-3 and 4-6. Such a comparison reveals that for the
Isolator2 element use of either a realistic value for the linear effective stiffness or a very
small value leads to nearly identical results.
57

-
0::
«
W
I
Cf)
W
Cf)
«
OJ
-
0::
«
W
I
(J)
W
(J)
«
OJ
-
0::
«
W
I
(J)
W
(J)
«
OJ
0.3
I-
I
c.9 0
W
S
-0.3
WITHOUT VERTICAL DAMPING ELEMENTS •
REALISTIC VALUES OF HORIZ. DOF ke
11 EIGENMOOES
.. _-- EXPERIMENTAL
-·-SAP2000
-2.5 o
0.3
I-
I
(9
0
W
S
-0.3
WITHOUT VERTICAL DAMPING ELEMENTS
HORIZ. DOF ke=O.0001 kiplin
11 EIGENMODES
._ ... EXPERIMENTAL
-SAP2000
-2.5 o
0.3
I-
I
(9
0
W
S
WITHOUT VERTICAL DAMPING ELEMENTS :
REALISTIC VALUES FOR HORIZ. OOF ke
26 RITZ VECTORS
2.5
2.5
· ..... EXPERIMENTAL
-SAP2000
-0.3 +-----i-'-----r---,---.,------r----.--,.---,-----.------i
-2.5 o 2.5
Figure 4-7 Comparison of Analytical and Experimental Results on the Base Shear-
Displacement Loop. Analysis without Vertical Damping Elements.
58

l-
I
c.9
W
S
0:::
«
w
I
(f)
W
(f)
«
(()
w
U
0.3 .,--------------------------,
o
WITH VERTICAL DAMPING ELEMENTS
REALISTIC VALUES OF HORIZ. DOF ke
11 EIGENMODES
EXPERIMENTAL
-SAP2000
-0.3 -t---,------r--..----,-----;.--....-------r------r--....-----i
-2.5 o 2.5
4 ,-----------------------------------------------------,
EXTERIOR BEARING
~O
U-
0:::
«
w
I
(f)
.. EXPERIMENTAL
-SAP2000
-4 +----.----~----~---,----_r----._--_,----._----r_--~
-2.5 o 2.5
Figure 4-8 Comparison of Analytical and Experimental Results on Shear Force-
Displacement Loops. Analysis with Vertical Damping Elements and
Realistic Values of Linear Effective Stiffness.
59

SECTIONS
ANALYSIS OF EXPERIMENTAL RESPONSE OF A 3-STORY BUILDING
MODEL WITH LINEAR AND NONLINEAR VISCOUS FLUID DAMPERS
5.1 Introduction
The structure analyzed in this section is a 3-story quarter length scale steel model
with a fluid viscous energy dissipation system. This model was used in several shake
table studies of active, semi-active and passive motion control systems (Chung et aI.,
1988; Constantinou and Symans, 1992; Symans and Constantinou, 1995; Seleemah and
Constantinou, 1997). Particularly, the study of Seleemah and Constantinou (1997)
included the use of linear and nonlinear fluid viscous dampers in a passive energy
dissipation system. It is a simple structural system and thus represents an ideal situation
for verifying the viscous damper element in SAP2000.
The structure was originally designed as a small structural testing system, and not
as a scaled model of an actual building. It underwent extensive testing over a period of
ten years and at the time prior to the tests of Seleemah and Constantinou (1997) it was
damaged, had several cracks and exhibited brittle behavior. The frame was repaired by
enhancing the section of the first story columns, by inhibiting the further propagation of
cracks (drilling of holes at crack tips) and by welding several small plates over the cracks
in order to provide for proper load paths. Figure 5-1 shows a schematic of the repaired
structure, including the added weight.
61

The model was tested in a variety of configurations, of which the one shown in
Figure 5-2 is analyzed herein. This configuration is a 3-story moment frame with
complete vertical distribution of diagonally placed fluid viscous dampers. The weight at
each floor level (including the tributary weight from beams and columns) was 9.38 kN
(mass of9.56 N-s2/cm).
Six linear viscous dampers were used (three on each of the two frames), and then
in another series of tests six nonlinear dampers were used. Three of the linear dampers
were tested to velocities of up to 420 mm/sec and found to exhibit nearly linear behavior,
which could be represented as
F=C u
o
(5-1)
where F = force, u= velocity, Co = damping coefficient equal to 16 N-sec/mm. The three
tested dampers did not have identical behavior, with the actual value of Co being in the
range of 13.5 to 18.5 N-sec/mm.
All six nonlinear dampers were tested and found to exhibit a behavior described
by
(5-2)
with a = 0.5 and Co in the range of 220 to 300 N-(sec/mm)Y2. Specifically, two dampers
had C = 220 N-(sec/mm)Y2 and were placed at the third story, two had C = 235 N-
o 0
(sec/mm)Y2 and were placed at the second story, and the two had Co = 300 N-(sec/mm)Y2
and were placed at the first story.
62

I
... 122.5 em ~ 1
STEEL --...
..,.--
II 'I........ - BALLAST ~[g~ID~
BLOCKS
...,; E
po. a
..,
....:e
IIIQ
....-.,.._ ST 2x3.85
(CUT WITH
d=1.5 In.)
SHAKING TABLE
.. ..
TESTING DIRECTION
FRONT VIEW
--i 38.1 1'11'1 r-
C
L 1~X1%X%
(TYP.) - -
SHAKING TABLE
SIDE VIEW
67 l'1l'i
L
-.-11- 6.31'11'1
SECTION A-A SECTION B-B
Figure 5-1 Schematic of Tested Model
63

6 DAMPERS
Figure 5-2 Schematic of One of the Tested Configurations
Interestingly, (5-2) described well the behavior of the nonlinear dampers for
velocities exceeding about 15 mm/s. For velocities below this limit the behavior was
essentially linear.
The model was tested with only horizontal seismic excitation using several scaled
historic earthquake records. The experimental results obtained for the SOOE component
of the 1940 EI Centro record (tests No. L36EI00 and N36EI00) are compared herein
with the analysis results of SAP2000. This record was compressed in time by factor of
two to satisfy the similitude requirements of the quarter length scale model.
5.3 Modeling in SAP2000
Due to symmetry, only one-half of the structure was modeled as a plane frame.
Figure 5-3 illustrates the model. Masses were concentrated at the column-to-beam joints,
and floor joints were constrained as diaphragm for reducing the degrees of freedom and
for better representing the behavior of the floors which were stiffened by the added steel
64

76.2 em
I
120.5 em
"I Joints Constrained
.-______________________ 1;- as Diaphragm (Typ. all floors)
( 7 8 )
40.25 em
13
26 em
Nllink Element,
Damper Property
(Typ. of Diagonal Elements)
l- 5~----~------ 6
Rigid (ryp.)
76.2 eml 11
,
I
26 emf
.;'
1 I
l- 3___---...l..-.-.--___ 4
I
/
E_I19_Qffset .-
(all jOints)
---- , -
iI
i
100.5 enl
i
!
t
80.25 em
8 em
~,
'--~ Mass 2.39 N s2jcm
(only UX)
/ Rigid
---.120 em
---.l
' - Fixed Ground
Node (ryp.)
x
Figure 5-3 Illustration of SAP2000 Model of 3-story Frame with Viscous Dampers
weights. Frame elements were used together with specified offset and dgid-end-factor
values. The value of the rigid end factor was specified to be 0.6 on the basis of
eigenvalue analysis of the frame without dampers and comparison of experimental and
analytical periods and mode shapes. Table 5-1 presents a comparison of these modal
properties, where it may be seen that there is an excellent agreement between the
experimental and analytical results.
65

There are two options in SAP2000 for modeling linear dampers:
(a) Element, Nllink, damper property, linear analysis type with ke = 0 and ce = 16 N-
sec/mm.
(b) Element Nllink, damper property, nonlinear analysis type with ke = 0, k = 1,000,000
N/cm, C = 16 N-sec/mm and cexp = 1.0.
The value of stiffness k is large enough to ensure that the element behaves as a pure
damper. The value is also consistent with the actual stiffness of the braces used to
connect the dampers to the frame. These braces were 1Yz x 1Y2 X 'i4 equal leg angles with
length of about either 35 or 70 cm. Their actual stiffness was larger than 1,000,000
N/cm. Both options were used and the calculated response was not exactly the same.
The input files in the supplied diskette contain further information on the
specified damping ratios for each of the three modes of vibration. The specified damping
ratios are those identified in the experiments for the frame without dampers. It should be
noted that due to the modeling with constrained floor nodes, rigid elements and
horizontal only masses, the model has effectively three degrees of freedom. Accordingly,
it is essentially the same as that llsed by Seleemah and Constantinou (1997) for the
analysis of the tested frame.
66

Table 5-1 Experimental and Analytical Modal Properties of 3-story Model
without Dampers
PERIOD (sec)
EXPERIMENTAL MODE SHAPES
(associated with horizontal displacements)
SAP2000 MODE SHAPES
5. 4 Analysis Results and Comparison to Experiment
Figures 5-4 and 5-5 present calculated and experimental story shear force-drift
loops and histories of story drift for the structure with linear dampers. The analysis was
conducted for the linear model of dampers and using the linear analysis option. The
experimental drifts were directly measured with displacement transducers, whereas the
experimental shear forces were obtained by calculation from the floor acceleration
records and the estimated distribution of mass. The two sets of results are in good
agreement. In general, the results of SAP2000 are essentially the same as those obtained
in the analyses of Seleemah and Constantinou (1997).
67

0.4
0:::
«
W
I I-
(f) I
~ c.? 0
0:: W
0 S
I-
CJ)
"0
'-
("')
-0.4
0.4
--
0::
«
W
I I-
CJ) I
~ c.? 0
0:: W
0 S
I-
CJ)
"0
C
N
-0.4
-1
-1
3rd STORY
WEIGHT =28.14 kN
HEIGHT = 762 mm
o
..... EXPERIMENTAL
(Test No. L36E100)
-SAP2000
3rd STORY DRIFT / HEIGHT (%)
2nd STORY
HEIGHT =762 mm
o
.0 ~ • • " .
..... EXPERIMENTAL
(Test No. L36E100)
-SAP2000
2nd STORY DRIFT / HEIGHT (%)
1
1
0.4 -,------------------------------,
0::
«
w
I I-
CJ) I
~ c.? 0
0:: W
o S
I-
CJ)
1st STORY
HEIGHT =813-mm
....-'.
.... EXPERIMENTAL
(Test No. L36E100)
-SAP2000
-0.4 +------r----.---.------.--,-----,-----.-----,,-----.-----l
-1 o 1
15t STORY DRIFT / HEIGHT (%)
Figure 5-4 Comparison of Analytical and Experimental Normalized Story Shear
Force-Drift Loops of Structure with Linear Dampers (linear analysis
type, linear damper model)
68

l-
I
(9
1 ~--------------------------------------------------~
W
I
l-
LL
O::~O+--~
0""""
>-
0::
o
I-
(j)
"E HEIGHT = 762 mm
("') -1
o 10
TI~E (sec)
3rd STORY
.. EXPERIMENTAL
(Test No. L36E100)
-SAP2000
20
l-
I
(9
1 ~--------------------------------------------------~
W
I
--
l-
LL
0:: ~ 0 +----''1
0--."
>-
0::
o
I-
(j)
"0 HEIGHT:= 762 mm
~ -1
o 10
TIME (sec)
2nd STORY
..... EXPERIMENTAL
(Test No. L36E100)
-SAP2000
20
l-
I
(9
1 ,-------------------------------------------------~
W
I
--
l-
LL
0::~0+---/"';
0""""
>-
0::
o
I-
(j)
-
(/) HEIGHT = 813 mm
1st STORY
.... EXPERIMENTAL
(Test No. L36E100)
----.- SAP2000
-1 +-----~--~----~--~~--~----~--~----~----~--~
o 10
TIME (sec)
20
Figure 5-5 Comparison of Analytical and Experimental Histories of Drift of
Structure with Linear Dampers (linear analysis type, linear damper
model)
69

Figure 5-6 is the same as Figure 5-4 but with the analytical results produced with
the nonlinear damper model with cexp = 1.0. While insignificant for practical purposes,
there is a small difference between the calculated responses using the linear and nonlinear
damper options.
Finally, Figures 5-7 and 5-8 compare the experimental and calculated response of
the structure with nonlinear dampers. Program SAP2000 underestimates the
displacement response by a significant amount. The calculated response did not improve
when adjustments were made to the stiffness k from the realistic value of 1,000,000 N/cm
to lower values (250,000 N/cm) or when Ritz rather than eigenvectors were used, or
when masses for the vertical degrees of freedom were introduced.
To provide further insight into this discrepancy, a simple one degree of freedom
system was analyzed: an example in Chapter X of Soong and Constantinou (1994) of a
linear elastic system with a lumped weight of 7000 kN and period of 2 sec, and with a
nonlinear viscous element described by (5-2) with Co = 25.13 kN (sec/mm)Y' and a = 0.5.
The SAP2000 results were nearly identical to those reported in Soong and Constantinou
(1994), which were produced with a rigorous integration scheme using a predictor-
corrector method.
The interested reader is referred to Seleemah and Constantinou (1997) for a good
comparison of experimental and analytical results, the latter produced with essentially the
same model. On the basis of this study, it is likely that a contributor to the discrepancy is
the inadequacy of the model of the dampers in SAP2000 to represent the low velocity
behavior of the nonlinear dampers.
70

0.4~--------------------------------------------------
0::
«
w
I I-
(f) I
>- C) 0
0:: w
~$
(f)
"0
...
(V)
3rd STORY
WEIGHT =28.14 kN
HEIGHT = 762 mm
... " EXPERIMENTAL
(Test No. L36E100)
-SAP2000
-OA +------,------,------.-------r------;-----r-----,------,r------r---~
OA
......
0::
«
w
I I-
(J) I
>- C) 0
0:: W
0 $
I-
(J)
"0
t:
N
-OA
-1
2nd STORY
HEIGHT =762 mm
o
3rd STORY DRIFT / HEIGHT (%)
--,. EXPERIMENTAL
(Test No. L36E100)
-SAP2000
1
-1 o 1
OA
......
0::
«
w
I I-
(f) I
>- C)
0
0:: W
0 $
I-
(f)
(j)
.,.-
-0.4
1st STORY
HEIGHT = 813'mm
-1
o
-- .. , EXPERIMENTAL
(Test No. L36E100)
-SAP2000
1st STORY DRIFT / HEIGHT (%)
1
Force-Drift Loops of Structure with Linear Dampers (nonlinear
analysis type, nonlinear damper model with cexp = 1.0)
71

--
0:::
«
UJ
I
CJ)
r
a::
0
I-
(j)
'"0
....
C"')
--
a::
«
w
I
(j)
r
a::
0
I-
(j)
'"0
C
N
a::
«
w
I
U)
r
a::
0
I-
CJ)
Vi
~
0.4
I-
I
(9
0
UJ
S
3rd STORY
WEIGHT =28.14 kN
HEIGHT =762 mm
..... EXPERIMENTAL
(Test No. N36E100)
-SAP2000
-0.4 +----,----.----r--.----,--,---.------;--r----.--,.---,--.-----.--~__l
-0.8
0.4
2nd STORY
I-
I
(9
0
w
S
HEIGHT = 762 mm
-0.4
-0.8
0.4
1st STORY
I-
I
(9
0
w
S
HEIGHT =.
813 mm
-0.4
-0.8
o
3rd STOR! DRIFT / HEIGHT (%)
o
.... ' EXPERIMENTAL
(Test No. N36E100)
-SAP2000
o
... " EXPERIMENTAL
(Test No. N36E100)
-SAP2000
1st STORY DRIFT / HEIGHT (%)
0.8
0.8
0.8
Force-Drift Loops of Structure with Nonlinear Dampers
72

~ 0.8 .---------------------------------------------------~
I
~
W
I
~
ll.. ........
cr '#. 0 +---~
0---
>-
cr
o
~
(j)
"0
I- HEIGHT = 762 mm
3rd STORY
. EXPERIMENTAL
(Test No. N36E100)
-SAP2000
(") -0.8 +---,.__--.---..--,-----,,----.---..---,-----,,----1
o 10
TIME (sec)
20
~ 0.8 .-------------------------------------------------~
I
~
W
I
~
ll..
........
cr ::oR 0 +-----.
0!2...-
>-
2nd STORY
~ ..... EXPERIMENTAL
t) (Test No. N36E100)
"0 HEIGHT!= 762 mm - SAP2000
~ -0.8 +---r---.---r----._---,.__--.---~--._----,.__--~
o 10
TIME (sec)
20
~
I
~
W
I
0.8.--------------------------------------------------.
~
ll.. ........
cr '#. 0 +----'1
0---
>-
cr
o
~
(j)
HEIGHT = 813 mm
1st STORY
..... EXPERIMENTAL
(Test No. N36E100)
-SAP2000
-0.8+---~----~---.----~----~--~----._--~----~--~
o 10
TIME (sec)
20
Figure 5-8 Comparison of Analytical and Experimental Histories of Drift of
Structure with Nonlinear Dampers
73

SECTION 6
ANALYSIS OF EXPERIMENTAL RESPONSE OF A MODEL
WITH A TOGGLE BRACE-DAMPER ENERGY DISSIPATION SYSTEM
6.1 Introduction
The analyzed structure is a half length scale steel model used to test a novel
energy dissipation system configuration termed the toggle brace-damper. The concept,
theoretical development, and experimental and analytical results are presented in
Constantinou et ai., (1997) and in the M.S. thesis of Hammel (1997). Moreover, a brief
description may be found in Constantinou (l998a).
Figure 6-1 illustrates the tested frame. Two such frames were used to support a
143 kN concrete block. The frame is equipped with a toggle brace (part DAC) which
effectively acts as a shallow truss. Viscous fluid dampers are installed either in the lower
damper configuration (between A and B as shown in Figure 6-1) or in the upper damper
configuration (which is more effective) as shown in the photograph of Figure 6-2, which
was taken during the shake table testing.
The operation of the toggle brace-damper system is as follows. On lateral
displacement of the frame (drift u as shown in Figure 6-1), joint A moves upwards
resulting in extension of the lower damper or compression of the upper damper. The
75

----r
I
!
iI
I
Ei
EI E
C") E
...r- l"-
a N
I"- m
';II ..-
..c'
I
--L
...r-
N
X
co
S
143 kN CONCRETE
BLOCK PIN-CONNECTED
AT THESE LOCATIONS
I
1_"""E-------.-.:f"-.:=~2::...;1~O~4~.5~m!..'..!m~-----~~1
2540 mm
TYPE 1 TYPE 2
/ CONNECTION CONNECTION ~
W8x21
c
TS 3x3x3/16
SIMPLE
81=31.9°
CONNECTION
(TYP.l
/
~PPORTING
£,=1429 mm
BEAM
,

Figure 6-1 Tested Frame with Toggle Brace-Damper System
76
U..

Figure 6-2 View of Tested ,Structure with Upper Damper Configuration on the
Shaking Table
77

change of length of the damper is the damper displacement uD
' which is related to the
drift: u:
U D =fu (6-1)
The magnification factor f depends on the geometry (specifically angles 8, and 82) and
the intent is to achieve large values. In the tested configurations, f assumed values of
about 2.5 and 3.0 in the lower and upper damper configurations, respectively. By
comparison, a horizontally placed damper on top of a chevron brace has f = 1.0, and a
diagonally placed damper has f less than 1.0.
Since the energy dissipated is proportional to the product of the peak damper
force and the peak damper displacement, effective energy dissipation is achieved with
low peak damper force when the system is configured for a large value of the
magnification factor f. This results in a lower cost for the dampers and extends their
applicability to stiff structural systems.
The tested structure, as illustrated in Figures 6-1 and 6-2, had a fundamental
period of about 0.3 sec, and a damping ratio of 0.04 without dampers, 0.22 with dampers
in the lower configuration (as in Figure 6-1) and 0.26 in the upper configuration (as in
Figure 6-2). The dampers were fluid viscous with linear behavior as described by (5-1)
with C = 15.4 N - sec/mm (= 88 lbs-sec/in.) to velocities of up to 500 mm/sec. Two such
()
dampers were used.
The frame was tested on a shake table in a variety of configurations. Herein
results are presented for the configuration shown in Figure 6-1 (lower damper) and using
the SOOE component of the 1940 EI Centro earthquake. This record was compressed in
time by 12 to satisfy similitude requirements.
78

6.3 Modeling in SAP2000
The modeling was essentially identical to the one developed in the ANSYS
program (Swanson Analysis Systems, 1996) and reported in Constantinou et al. (1997).
Figures 6-3 and 6-4 illustrate the ANSYS model. The supplied diskette contains the
input files, where the coordinates and section properties may be found. It should be
noted that the model is that of one frame of the tested structure. Accordingly, half of the
total mass of the structure is assigned to it.
Program SAP2000 could model this frame in a more direct way, that is, by using
the offset, rigid-end factor and constraints options. However, in the interest of
comparing the results of the two programs, the ANSYS model was duplicated 111
SAP2000.
The linear viscous dampers were modeled in SAP2000 using the Nllink element,
damper property using linear type of analysis while maintaining six eigenvectors with an
assigned damping ratio of 0.04.
6.4 Analysis Results and Comparison to Experiment
Figures 6-5 to 6-7 present histories of the frame drift (displacement ofjoint 3 with
respect to the ground), histories of the frame acceleration (joint 3), and loops of the
damper force vs. damper displacement. The experimental results are the average of the
recorded responses at the two frames of the tested structure (east and west sides). The
test number is AELRSL02 (see Constantinou et al., 1997).
The figures compare the experimental results to the analytical results obtained by
SAP2000, and then the results produced by the two programs. The two programs produce
79

y
PIN (MOMENT
RELEASE) [2]
PIN (MOMENT
/
RELEASE)
~ PIN (MOMENT RELEASE)
o @ WITH ROTATIONAL SPRIN~@ @
o ®0 ®~~
0~~~~---------r~--------~~~~
r;;tm~ r.j2l', f13l ~ ~
L3J l!2J ~ , ~ ~ 14 15 ~
(3) ' @]® @
,
'_ALTERNATIVE @
LOCATION
FOR DAMPER
ELEMENT§
,,,,,,,,,,,,
@@
7~DAMPER
PIN (MOMENT , ELEMENT
RELEASE) ,
----->~ X
,,,,
4
ROTATIONAL
SPRING~
Figure 6-3 Schematic Illustrating Joints and Elements in ANSYS Model of Frame
with Rigid-Simple Connections (for coordinates and section properties
see Input File)
80

3750lbs
7500lbs
3750lbs
500tbs
8) @
~ 851bs 851bs
G)~--~~--------------------------~~~.~
20lbs

651bs

35tbs

~
Figure 6-4 Schematic Illustrating Location of Lumped Masses in ANSYS Model of
Frame (values denote weight in pounds)
81

nearly identical results, which are in good agreement with the experimental response.
82

12 ,---------------------------------------------~
---
E
E
"-"
I-
Z
W
JOINT 3
~ 0 -+--~'""
w
u
«
..J
0..
Cf)
o
f:
...... EXPERIMENTAL
(Test No. AELRSL02)
-SAP2000
-12 +---~----~--~--~----~--~--~----~--~--~
o 2 4 6 8 10
TIME (sec)
12 ~----------------------------------------------~
E
E
"-"
I-
Z
W
JOINT 3
~ 0 -t---------.;cc.7
W
U
«
..J
0..
Cf)
o
ANSYS
-SAP2000
-12 +---~----~--~----~--~----~--~----~--~~--~
o 2 4 6 8 10
TIME (sec)
Figure 6-5 Comparison of Analytical and Experimental Results on History of
Frame Drift
83

w
U
0:::
10 ~--------------------------------------------~
..... EXPERIMENTAL
(Test No. AELRSL02)
-SAP2000
~ 0
[t
W
0..
~
«
o
w
U
0:::
-10 +---~----~--~----~--~----~--~----~--~----~
-25 o 25
DAMPER DISPLACEMENT (mm)
10 ~--------------------------------------------~
····ANSYS
-SAP2000
~ 0
0:::
W
n...
2
«
o
-10 +---~----~--~----~--~----~--~----~--~--~
-25 o 25
DAMPER DISPLACEMENT (mm)
Figure 6-6 Comparison of Analytical and Experimental Damper Force-
Displacement Loops
84

.-...
Ol
'-"
Z
0
I-
<t:
0::
w
...J
W
U
U
<t:
I-
Z
0
J
0.5
JOINT 3
0.0
.. EXPERIMENTAL
(Test No. AELRSL02)
-SAP2000
-0.5 +---,----,--,----,----,.---,--,-----,----,-----1
Ol
'-"
Z
0
I-
<:t:
0::
w
...J
W
U
U
<:t:
I-
Z
0
J
o 2
0.5
JOINT 3
0.0
4 6
TIME (sec)
8
ANSYS
-SAP2000
10
-0.5 +-----,.---,,----..,-----,.--_,,------.-----,---,-----,------t
o 2 4 6 8 10
TIME (sec)
Figure 6-7 Comparison of Analytical and Experimental Histories of Acceleration
of Beam to Column Connection
85

SECTION 7
CONCLUSIONS
A number of structures with seIsmIC isolation and energy dissipation systems
were modeled and analyzed using SAP2000, and the results were compared to either
experimental results or to results obtained with programs 3D-BASIS-ME and ANSYS.
In these examples, the element Nllink of SAP2000 in the Isolatorl, the Isolator2, and
the linear and nonlinear damper property configurations was tested. Input files for each
example were provided and comments on the modeling were presented. Alternative
modeling approaches and their effect on the calculated response were also presented.
In general, the use of SAP2000 produced results in excellent agreement with other
programs and in good agreement with experimental results. This included the case of a
tested isolated frame with uplifting Friction Pendulum bearings. However, modeling in
SAP2000 was not always straightforward. Specifically, we made a number of
observations in the behavior of the utilized elements, of which the following are of
interest to users of this program:
(a) For the Isolator! and Isolator2 options of element Nllink, the linear effective
stiffness for the shear degrees of freedom may have to be specified with a very small
value rather than a realistic value.
(b) The Isolator2 option of element Nllink, which models Friction Pendulum bearings,
may produce erroneous results unless it is combined with vertical linear damping
elements to suppress fluctuations in the calculated forces resulting, likely, from
numerical instability problems.
87

(c) There is a need to better describe the damper option of the NIlink element. As
described in the manual of the program, this element is a Maxwell element. Yet, the
element could be used to successfully describe behavior not possible for the Maxwell
element and for the utilized combination of parameters (see Section 2).
Finally, there is a need to revisit the nonlinear viscous damper option of element
Nllink. As described in Section 6, the use of this element did not produce accurate
results in the analysis of a tested frame with nonlinear viscous dampers.
88

SECTION 8
REFERENCES
I. Al-Hussaini, T.M., Zayas, V. and Constantinou, M.C. (1994), "Seismic Isolation of
Multi-Story Frame Structures Using Spherical Sliding Isolation Systems," Report No.
NCEER-94-0007, National Center for Earthquake Engineering Research, Buffalo,
New York.
2. Chung, L.L., Lin, R.C., Soong, T.T., and Reinhorn, A.M. (1988), "Experimental
Study of Active Control of MDOF Structures Under Seismic Excitations," Report No.
NCEER-88-0025. National Center for Earthquake Engineering Research, Buffalo,
New York.
3. Computers and Structures, Inc., (1997), "SAP2000, Integrated Finite Element
Analysis and Design of Structures", Version 6.1, Berkeley, CA.
4. Constantinou, M.C. and Symans, M.D. (1992), "Experimental and Analytical
Investigation of Seismic Response of Structures with Supplemental Fluid Viscous
Dampers," Report No. NCEER-92-0032, National Center for Earthquake Engineering
Research, Buffalo, New York.
5. Constantinou, M.C., Tsopelas, P. and Hammel, W. (1997), "Testing and Modeling of
an Improved Damper Configuration for Stiff Structural Systems", Technical Report
of the Center for [ndustrial Effectiveness, University at Buffalo, State University of
New York, Buffalo, NY, 14260.
89

6. Constantinou, M.C. (1998a),"Introduction to Passive Energy Dissipation", in Seminar
Papers of 1998 Spring Seminar, Structural Engineers Association of Northern
California, March.
7. Constantinou, M.C. (1998b), "Application of Seismic Isolation Systems in Greece",
Proceedings of Structural Engineers World Congress, San Francisco, CA, JUly.
8. Hammel, W. (1997), "Testing and Modeling of an Improved Damper Configuration
for Stiff Structural Systems," M.S. Thesis, University at Buffalo, State University of
New York, Buffalo, NY 14260, August.
9. Haroun, M.A. and Housner, G.W. (1981), "Seismic Design of Liquid Storage Tanks",
J Technical Councils, ASCE, 107 (TCI), 191-207.
10. Hibbit, Karlsson and Sorensen, Inc., (1997) "ABAQUS/Standard, User's Manual",
Version 5.7, Pawtucket, Rhode Island.
11. International Conference of Building Officials (1994), "Uniform Building Code",
Whittier, CA.
12. Nagarajaiah, S., Reinhorn, A.M. and Constantinou, M.C. (1989), "Nonlinear
Dynamic Analysis of Three-Dimensional Base Isolated Structures (3D-BASIS)",
Report No. NCEER-89-00 19, National Center for Earthquake Engineering Research,
Buffalo. New York.
13. Reinhorn, A.M., Nagarajaiah, S., Constantinou, M.C., Tsopelas, P. and Li, R. (1994),
"3-D-BASIS-TABS: Version 2.0 Computer Program for Nonlinear Dynamic Analysis
of Three Dimensional Base Isolated Structures", Report No. NCEER-94-0018,
National Center for Earthquake Engineering Research, Buffalo, New York.
90

14. Seleemah, A.A. and Constantinou, M.C. (1997), "Investigation of Seismic Response
of Buildings with Linear and Nonlinear Fluid Viscous Dampers", Report No.
NCEER-97-0004, National Center for Earthquake Engineering Research, Buffalo,
New York.
15. Soong, T.T. and Constantinou, M.C (1994), "Passive and Active Structural Vibration
Control in Civil Engineering", Springer-Verlag, Wien-New York.
16. Swanson Analysis Systems IP, Inc., (1996), "ANSYS, Finite Element Program and
User's Manual", Version 5.3, Houston, PA.
17. Symans, M.D. and Constantinou, M.C. (1995), "Development and Experimental
Study of Semi-Active Fluid Damping Devices for Seismic Protection of Structures",
Report No. NCEER-95-0011, National Center for Earthquake Engineering Research,
Buffalo, New York.
18. Theodossiou, D. and Constantinou, M.e. (1991), "Evaluation of SEAOC Design
Requirements for Sliding Isolated Structures", Report No. NCEER-91-0015, National
Center for Earthquake Engineering Research, Buffalo, New York.
19. Tsopelas, P.C., Constantinou, M.C. and Reinhorn, A.M. (1994), "3D-BASIS-ME:
Computer Program for Nonlinear Dynamic Analysis of Seismically Isolated Single
and Multiple Structures and Liquid Storage Tanks", Report No. NCEER-94-0010,
National Center for Earthquake Engineering Research, Buffalo, New York.
20. Wilson, E.L, Hollings, J.P. and Dovey, H.H. (1975), "ETABS-Three Dimensional
Analysis of Building Systems", Report No. UCB/EERC 75113, Ealihquake
Engineering Research Center, University of California, Berkeley, CA.
91

21. Winters, e. W. and Constantinou, M.e. (1993), "Evaluation of Static and Response
Spectrum Analysis Procedures of SEAOC/UBC for Seismic Isolated Structures",
Report No. NCEER-93-0004, National Center tor Earthquake Engineering Research,
Buffalo, New York.
92

Multidisciplinary Center for Earthquake Engineering Research
List ofTechnical Reports
The Multidisciplinary Center for Earthquake Engineering Research (MCEER) publishes technical reports on a variety of
subjects related to earthquake engineering written by authors funded through MCEER These reports are available from both
MCEER Publications and the National Technical Information Service (NTIS). Requests for reports should be directed to
MCEER Publications, Multidisciplinary Center for Earthquake Engineering Research, State University of New York at
Buffalo, Red Jacket Quadrangle, Buffalo, New York 14261. Reports can also be requested through NTIS, 5285 Port Royal
Road, Springfield, Virginia 22161. NTIS accession numbers are shown in parenthesis, ifavailable.
NCEER-87-0001 "First-Year Program in Research, Education and Technology Transfer," 3/5/87, (PB88-134275, A04, MF-
AOl).
NCEER-87-0002 "Experimental Evaluation of Instantaneous Optimal Algorithms for Structural Control," by R.C. Lin, T.T.
Soong and AM. Reinhorn, 4/20/87, (PB88-l34341, A04, MF-AO1).
NCEER-87-0003 "Experimentation Using the Earthquake Simulation Facilities at University at Buffalo," by AM. Reinhorn
and R.L. Ketter, to be published.
NCEER-87-0004 "The System Characteristics and Performance of a Shaking Table," by lS. Hwang, KC. Chang and G.C.
Lee, 6/1/87, (pB88-134259, A03, MF-A01). This report is available only through NTIS (see address given
above).
NCEER-87-000S "A Finite Element Formulation for Nonlinear Viscoplastic Material Using a Q Model," by O. Gyebi and G.
Dasgupta, 1112/87, (pB88-213764, A08, MF-AOl).
NCEER-87-0006 "Symbolic Manipulation Program (SMP) - Algebraic Codes for Two and Three Dimensional Finite Element
Formulations," by X. Lee and G. Dasgupta, 1119/87, (PB88-2l8522, AOS, MF-AOl).
NCEER-87-0007 "Instantaneous Optimal Control Laws for Tall Buildings Under Seismic Excitations," by IN. Yang, A
Akbarpour and P. Ghaemmaghami, 6/10/87, (pB88-134333, AOQ, MF-AOl). This report is only available
through NTIS (see address given above).
NCEER-87-0008 "IDARC: Inelastic Damage Analysis of Reinforced Concrete Frame - Shear-Wall Structures," by Yl Park,
AM. Reinhorn and S.K. Kunnath, 7/20/87, (PB88-13432S, A09, MF-AOl). This report is only available
NCEER-87-0009 "Liquefaction Potential for New York State: A Preliminary Report on Sites in Manhattan and Buffalo," by
M. Budhu, V. Vijayakumar, RF. Giese and L. Baumgras, 8/31/87, (PB88-l63704, A03, MF-AOl). This
report is available only through NTIS (see address given above).
NCEER-87-0010 "Vertical and Torsional Vibration of Foundations in Inhomogeneous Media," by AS. Veletsos and KW.
Dotson, 6/1/87, (PB88-13429l, A03, MF-A01). This report is only available through NTIS (see address
given above).
NCEER-87-00ll "Seismic Probabilistic Risk Assessment and Seismic Margins Studies for Nuclear Power Plants," by
Howard H.M. Hwang, 6/1S/87, (PB88-134267, A03, MF-AOl). This report is only available through NTIS
(see address given above).
NCEER-87-0012 "Parametric Studies ofFrequency Response of Secondary Systems Under Ground-Acceleration Excitations,"
by Y. Yong and Y.K. Lin, 6/10/87, (PB88-134309, A03, MF-AOl). This report is only available through
NTIS (see address given above).
NCEER-87-0013 "Frequency Response of Secondary Systems Under Seismic Excitation," by J.A HoLung, J. Cai and Y.K
Lin, 7/31187, (PB88-134317, A05, MF-A01). This report is only available through NTIS (see address given
above).
Fonnerly the National Center for Earthquake Engineering Research 93

NCEER-87-0014 "Modelling Earthquake Ground Motions in Seismically Active Regions Using Parametric Time Series
Methods," by G.w. Ellis and AS. Cakmak, 8/25/87, (pB88-134283, A08, MF-AOI). This report is only
available through NITS (see address given above).
NCEER-87-0015 "Detection and Assessment of Seismic Structural Damage," by E. DiPasquale and AS. Cakmak, 8/25/87,
(PB88-163712, A05, MF-AOI). This report is only available through NITS (see address given above).
NCEER-87-0016 "Pipeline Experiment at Parkfield, California," by J. Isenberg and E. Richardson, 9115/87, (pB88-163720,
A03, MF-AOI). This report is available only through NIlS (see address given above).
NCEER-87-0017 "Digital Simulation of Seismic Ground Motion," by M. Shinozuka, G. Deodatis and T. Harada, 8/31187,
(PB88-155197, A04, MF-AOl). This report is available only through NTIS (see address given above).
NCEER-87-0018 "Practical Considerations for Structural Control: System Uncertainty, System Time Delay and Truncation of
Small Control Forces," J.N. Yang and A Alcbarpour, 8110/87, (pB88-163738, A08, MF-AOl). This report is
only available through NIlS (see address given above).
NCEER-87-0019 "Modal Analysis of Nonclassically Damped Structural Systems Using Canonical Transfonnation," by J.N.
Yang, S. Sarkani and F.x. Long, 9/27/87, (PB88-187851, A04, MF-AOI).
NCEER-87-0020 "A Nonstationary Solution in Random Vibration Theory," by J.R. Red-Horse and P.D. Spanos, 11/3/87,
(PB88-163746, A03, MF-AOI).
NCEER-87-0021 "Horizontal hupedances for Radially Inhomogeneous Viscoelastic Soil Layers," by AS. Veletsos and K.W.
Dotson, 10115/87, (PB88-150859, A04' MF-AOI).
NCEER-87-0022 "Seismic Damage Assessment of Reinforced Concrete Members," by Y.S. Chung, C. Meyer and M.
Shinozuka, 10/9/87, (PB88-150867, A05, MF-AOI). This report is available only through NTIS (see
address given above).
NCEER-87-0023 "Active Structural Control in Civil Engineering," by T.T. Soong, 11/11187, (pB88-187778, A03, MF-AOI).
NCEER-87-0024 "Vertical and Torsional hupedances for Radially Inhomogeneous Viscoelastic Soil Layers," by K.W. Dotson
and AS. Veletsos, 12/87, (PB88-187786, A03, MF-AOl).
NCEER-87-0025 "Proceedings from the Symposium on Seismic Hazards, Ground Motions, Soil-Liquefaction and
Engineering Practice in Eastern North America," October 20-22,1987, edited by K.H. Jacob, 12/87, (PB88-
188115, A23, MF-AOI). This reportis available only through NITS (see address given above).
NCEER-87-0026 "Report on the Whittier-Narrows, California, Earthquake of October I, 1987," by J. Pantelic and A
Reinhorn, 11/87, (PB88-187752, A03, MF-AOI). This report is available only through NTIS (see address
given above).
NCEER-87-0027 "Design of a Modular Program for Transient Nonlinear Analysis of Large 3-D Building Structures," by S.
Srivastavand J.F. Abel, 12/30/87, (PB88-187950, A05, MF-AOl). This report is only available through
NTIS (see address given above).
NCEER-87-0028 "Second-Year Program in Research, Education and Technology Transfer," 3/8/88, (pB88-219480, A04, MF-
AOI).
NCEER-88-000l "Workshop on Seismic Computer Analysis and Design of Buildings With Interactive Graphics," by W.
McGuire, J.F. Abel and C.H. Conley, 1118/88, (pB88-187760, A03, MF-AOl). This report is only available
NCEER-88-0002 "Optimal Control of Nonlinear Flexible Structures," by J.N. Yang, F.X. Long and D. Wong, 1122/88,
(PB88-213772, A06, MF-AOl).

NCEER-88-0003 "Substructuring Techniques in the Time Domain for Primary-Secondary Structural Systems," by G.D.
Manolis and G. Juhn, 2/10/88, (PB88-213780, A04, MF-A01).
NCEER-88-0004 "Iterative Seismic Analysis of Primary-Secondary Systems," by A Singhal, L.D. Lutes and P.D. Spanos,
2/23/88, (PB88-213798, A04, MF-A01).
NCEER-88-0005 "Stochastic Finite Element Expansion for Random Media," by P.D. Spanos and R. Ghanem, 3114/88,
(PB88-213806, A03, MF-AOI).
NCEER-88-0006 "Combining Structural Optimization and Structural Control," by F.Y. Cheng and C.P. Pantelides, 1/10/88,
(PB88-213814, A05, MF-A01).
NCEER-88-0007 "Seismic Performance Assessment of Code-Designed Structures," by H.H-M. Hwang, J-W. Jaw and H-l
Shau, 3/20/88, (PB88-219423, A04, MF-AOI). This report is only available through NTIS (see address
given above).
NCEER-88-0008 "Reliability Analysis of Code-Designed Structures Under Natural Hazards," by H.H-M. Hwang, H. Ushiba
and M. Shinozuka, 2/29/88, (PB88-229471, A07, MF-A01). This report is only available through NTIS (see
address given above).
NCEER-88-0009 "Seismic Fragility Analysis of Shear Wall Structures," by J-W Jaw and H.H-M. Hwang, 4/30/88, (PB89-
102867, A04, MF-A01).
NCEER-88-001O "Base Isolation of a Multi-Story Building Under a Harmonic Ground Motion - A Comparison of
Performances of Various Systems," by F-G Fan, G. Ahmadi and I.G. Tadjbakhsh, 5118/88, (PB89-122238,
A06, MF-A01). This report is only available through NTIS (see address given above).
NCEER-88-0011 "Seismic Floor Response Spectra for a Combined System by Green's Functions," by F.M. Lavelle, L.A
Bergman and P.D. Spanos, 511/88, (pB89-102875, A03, MF-A01).
NCEER-88-0012 "A New Solution Technique for Randomly Excited Hysteretic Structures," by G.Q. Cai and Y.K. Lin,
5/16/88, (PB89-102883, A03, MF-A01).
NCEER-88-0013 "A Study ofRadiation Damping and Soil-Structure Interaction Effects in the Centrifuge," by K. Weissman,
supervised by lH. Prevost, 5/24/88, (PB89-144703, A06, MF-A01).
NCEER-88-0014 "Parameter Identification and Implementation of a Kinematic Plasticity Model for Frictional Soils," by lH.
Prevost and D.V. Griffiths, to be published.
NCEER-88-0015 "Two- and Three- Dimensional Dynamic Finite Element Analyses of the Long Valley Dam," by D.V.
Griffiths and lH. Prevost, 6117/88, (PB89-144711, A04, MF-A01).
NCEER-88-0016 "Damage Assessment ofReinforced Concrete Structures in Eastern United States," by AM.. Reinhorn, M.l
Seidel, S.K. Kunnath and Y.J. Park, 6/15/88, (PB89-122220, A04, MF-A01). This report is only available
NCEER-88-0017 "Dynamic Compliance of Vertically Loaded Strip Foundations in Multilayered Viscoelastic Soils," by S.
Ahmad and AS.M. Israil, 6117/88, (PB89-102891, A04, MF-A01).
NCEER-88-0018 "An Experimental Study of Seismic Structural Response With Added Viscoelastic Dampers," by R.C. Lin,
z. Liang, T.T. Soong and R.H. Zhang, 6/30/88, (PB89-122212, A05, MF-AOI). This report is available
only through NTIS (see address given above).
NCEER-88-0019 "Experimental Investigation of Primary - Secondary System Interaction," by G.D. Manolis, G. Juhn and
A.M. Reinhorn, 5/27/88, (PB89-122204, A04, MF-A01).

NCEER-88-0020 "A Response Spectrum Approach For Analysis of Nonclassically Damped Structures," by J.N. Yang, S.
Sarkani and F.X. Long, 4/22/88, (PB89-102909, A04, MF-AOl).
NCEER-88-0021 "Seismic futeraction of Structures and Soils: Stochastic Approach," by AS. Ve1etsos and AM. Prasad,
7/21188, (PB89-122196, A04, MF-AOl). This report is only available through NTIS (see address given
above).
NCEER-88-0022 "Identification of the Serviceability Limit State and Detection of Seismic Structural Damage," by E.
DiPasquale and AS. Cakmak, 6115/88, (pB89-122188, A05, MF-A01). This report is available only
NCEER-88-0023 "Multi-Hazard Risk Analysis: Case of a Simple Offshore Structure," by B.K. Bhartia and E.H. Vanrnarcke,
7/21/88, (PB89-145213, A05, MF-A01).
NCEER-88-0024 "Automated Seismic Design of Reinforced Concrete Buildings," by Y.S. Chung, C. Meyer and M.
Shinozuka, 7/5/88, (PB89-122170, A06, MF-A01). This report is· available only through NTIS (see address
given above).
NCEER-88-0025 "Experimental Study of Active Control of MDOF Structures Under Seismic Excitations," by L.L. Chung,
RC. Lin, T.T. Soong and AM. Reinhom, 7110/88, (PB89-122600, A04, MF-A01).
NCEER-88-0026 "Earthquake Simulation Tests of a Low-Rise Metal Structure," by J.S. Hwang, KC. Chang, G.C. Lee and
RL. Ketter, 811/88, (PB89-102917, A04, MF-A01).
NCEER-88-0027 "Systems Study ofUrban Response and Reconstruction Due to Catastrophic Earthquakes," by F. Kozin and
H.K Zhou, 9/22/88, (PB90-162348, A04, MF-A01).
NCEER-88-0028 "Seismic Fragility Analysis ofPlane Frame Structures," by H.H-M. Hwang and Y.K. Low, 7/31/88, (pB89-
131445, A06, MF-A01).
NCEER-88-0029 "Response Analysis ofStochastic Structures," by A Kardara, C. Bucher and M. Shinozuka, 9/22/88, (PB89-
174429, A04, MF-A01).
NCEER-88-0030 "Nonnormal Accelerations Due to Yielding in a Primary Structure," by D.C.K Chen and L.D. Lutes,
9/19/88, (PB89-131437, A04, MF-A01).
NCEER-88-0031 "Design Approaches for Soil-Structure futeraction," by AS. Veletsos, AM. Prasad and Y. Tang, 12/30/88,
(PB89-174437, A03, MF-AOl). This report is available only through NTIS (see address given above).
NCEER-88-0032 "A Re-evaluation of Design Spectra for Seismic Damage Control," by C.J. Turkstra and AG. Tallin,
Ilm88, (PB89-145221, A05, MF-AOl).
NCEER-88-0033 "The Behavior and Design ofNoncontact Lap Splices Subjected to Repeated fuelastic Tensile Loading," by
V.E. Sagan, P. Gergely and R.N. White, 12/8/88, (pB89-163737, A08, MF-AO1).
NCEER-88-0034 "Seismic Response of Pile Foundations," by S.M. Mamoon, P.K Banerjee and S. Ahmad, 1111/88, (pB89-
145239, A04, MF-AOI).
NCEER-88-0035 "Modeling of RIC Building Structures With Flexible Floor Diaphragms (IDARC2)," by AM. Reinhorn,
S.K. Kunnath and N. Panahshahi, 9m88, (PB89-207153, A07, MF-AOl).
NCEER-88-0036 "Solution of the Dam-Reservoir futeraction Problem Using a Combination of FEM, BEM with Particular
futegraIs, Modal Analysis, and Substructuring," by C-S. Tsai, G.C. Lee and RL. Ketter, 12/31/88, (pB89-
207146, A04, MF-A01).
NCEER-88-0037 "Optimal Placement of Actuators for Structural Control," by F.Y. Cheng and C.P. Pantelides, 8/15/88,
(PB89-162846, A05, MF-A01).
Fonnerlythe National Center for Earthquake Engineering Research 96

NCEER-88-0038 "Teflon Bearings in Aseismic Base Isolation: Experimental Studies and Mathematical Modeling," by A
Mokha, M.C. Constantinou and AM. Reinhom, 12/5/88, (pB89-218457, A10, MF-A01). This report is
available only through NTIS (see address given above).
NCEER-88-0039 "Seismic Behavior ofFlat Slab High-Rise Buildings in the New York City Area," by P. Weidlinger and M.
Ettouney, 10115/88, (pB90-145681, A04, MF-A01).
NCEER-88-0040 "Evaluation ofthe Earthquake Resistance of Existing Buildings in New York City," by P. Weidlinger and
M. Ettouney, 10115/88, to be published.
NCEER-88-0041 "Small-Scale Modeling Techniques for Reinforced Concrete Structures Subjected to Seismic Loads," by W.
Kim, A. El-Attar and R.N. White, 11122/88, (pB89-189625, A05, MF-AO1).
NCEER-88-0042 "Modeling Strong Ground Motion from Multiple Event Earthquakes," by G.W. Ellis and AS. Cakmak,
10115/88, (PB89-174445, A03, MF-A01).
NCEER-88-0043 "Nonstationary Models of Seismic Ground Acceleration," by M. Grigoriu, S.E. Ruiz and E. Rosenblueth,
7115/88, (PB89-189617, A04, MF-AOl).
NCEER-88-0044 "SARCF User's Guide: Seismic Analysis ofReinforced Concrete Frames," by Y.S. Chung, C. Meyer and M.
Shinozuka, 1119/88, (PB89-174452, A08, MF-AOl).
NCEER-88-0045 "First Expert Panel Meeting on Disaster Research and Planning," edited by 1. Pantelic and 1. Stoyle,
9115/88, (PB89-174460, A05, MF-A01).
NCEER-88-0046 "Preliminary Studies of the Effect of Degrading Infill Walls on the Nonlinear Seismic Response of Steel
Frames," by C.z. Chrysostomou, P. Gergely and IF. Abel, 12119/88, (PB89-208383, A05, MF-A01).
NCEER-88-0047 "Reinforced Concrete Frame Component Testing Facility - Design, Construction, Instrumentation and
Operation," by S.P. Pessiki, C. Conley, T. Bond, P. Gergely and R.N. White, 12116/88, (PB89-174478,
A04, MF-AOl).
NCEER-89-0001 "Effects of Protective Cushion and Soil Compliancy on the Response of Equipment Within a Seismically
Excited Building," by J.A. HoLung, 2116/89, (PB89-207179, A04, MF-A01).
NCEER-89-0002 "Statistical Evaluation of Response Modification Factors for Reinforced Concrete Structures," by H.H-M.
Hwang and J-W. Jaw, 2117/89, (PB89-207187, A05, MF-A01).
NCEER-89-0003 "Hysteretic Columns Under Random Excitation," by G-Q. Cai and Y.K. Lin, 119/89, (PB89-1965I3, A03,
MF-A01).
NCEER-89-0004 "Experimental Study of 'Elephant Foot Bulge' Instability of Thin-Walled Metal Tanks," by Z-H. Jia and
R.L. Ketter, 2/22/89, (PB89-207195, A03, MF-A01).
NCEER-89-0005 "Experiment on Performance ofBuried Pipelines Across San Andreas Fault," by 1. Isenberg, E. Richardson
and T.D. O'Rourke, 3/10/89, (PB89-218440, A04, MF-A01). This report is available only through NTIS
(see address given above).
NCEER-89-0006 "A Knowledge-Based Approach to Structural Design ofEarthquake-Resistant Buildings," by M. Subramani,
P. Gergely, C.H. Conley, J.F. Abel and A.H. Zaghw, 1115/89, (PB89-218465, A06, MF-A01).
NCEER-89-0007 "Liquefaction Hazards and Their Effects on Buried Pipelines," by T.D. O'Rourke and P.A. Lane, 2/1/89,
(PB89-218481, A09, MF-A01).

NCEER-89-0008 "Fundamentals of System Identification in Structural Dynamics," by H. hnai, C-B. Yun, O. Maruyama and
M. Shinozuka, 1/26/89, (PB89-207211, A04, MF-AOl).
NCEER-89-0009 "Effects of the 1985 Michoacan Earthquake on Water Systems and Other Buried Lifelines in Mexico," by
AG. Ayala and M.J. O'Rourke, 3/8/89, (pB89-207229, A06, MF-A01).
NCEER-89-ROlO "NCEER Bibliography of Earthquake Education Materials," by K.E.K. Ross, Second Revision, 9/1189,
(PB90-125352, AOS, MF-A01). This report is replaced by NCEER-92-0018.
NCEER-89-00l1 "fuelastic Three-Dimensional Response Analysis of Reinforced Concrete Building Structures (lDARC-3D),
Part I - Modeling," by S.K. Kunnath and AM. Reinhorn, 4/17/89, (PB90-114612, A07, MF-AOl). This
report is available only through NTIS (see address given above).
NCEER-89-0012 "Recommended Modifications to ATC-14," by C.D. Poland and lO. Malley, 4/12/89, (PB90-108648, A15,
MF-A01).
NCEER-89-0013 "Repair and Strengthening of Beam-to-Column Connections Subjected to Earthquake Loading," by M.
Corazao andAl Durrani, 2/28/89, (PB90-109885, A06, MF-AOl).
NCEER-89-0014 "Program EXKAL2 for Identification of Structural Dynamic Systems," by o. Maruyama, C-B. Yun, M.
Hoshiya and M. Shinozuka, 5/19/89, (PB90-109877, A09, MF-A01).
NCEER-89-0015 "Response of Frames With Bolted Semi-Rigid Connections, Part I - Experimental Study and Analytical
Predictions," by P.J. DiCorso, AM. Reinhorn, J.R. Dickerson, J.B. Radziminski and W.L. Harper, 611/89,
to be published.
NCEER-89-00l6 "ARMA Monte Carlo Simulation in Probabilistic Structural Analysis," by P.D. Spanos and M.P. Mignolet,
7110/89, (PB90-lD9893, A03, MF-A01).
NCEER-89-P017 "Preliminary Proceedings from the Conference on Disaster Preparedness - The Place of Earthquake
Education in Our Schools," Edited by K.EK Ross, 6/23/89, (PB90-lD8606, A03, MF-AOl).
NCEER-89-0017 "Proceedings from the Conference on Disaster Preparedness - The Place of Earthquake Education in Our
Schools," Edited by K.E.K. Ross, 12/31/89, (PB90-207895, A012, MF-A02). This report is available only
NCEER-89-0018 "Multidimensional Models of Hysteretic Material Behavior for Vibration Analysis of Shape Memory
Energy Absorbing Devices, by E.l Graesser and FA Cozzarelli, 6nt89, (pB90-164146, A04, MF-A01).
NCEER-89-0019 "Nonlinear Dynamic Analysis of Three-Dimensional Base Isolated Structures (3D-BASIS)," by S.
Nagarajaiah, AM. Reinhom and M.C. Constantinou, 8/3/89, (PB90-161936, A06, MF-A01). This report
has been replaced by NCEER-93-0011.
NCEER-89-0020 "Structural Control Considering Time-Rate ofControl Forces and Control Rate Constraints," by F.Y. Cheng
and C.P. Pantelides, 8/3/89, (PB90-120445, A04, MF-AOl).
NCEER-89-0021 "Subsurface Conditions of Memphis and Shelby County," by K.w. Ng, T-S. Chang and H-H.M. Hwang,
7/26/89, (PB90-120437, A03, MF-A01).
NCEER-89-0022 "Seismic Wave Propagation Effects on Straight Jointed Buried Pipelines," by K. Elhmadi and M.l
O'Rourke, 8/24/89, (pB90-l62322, AlD, MF-A02).
NCEER-89-0023 "Workshop on Serviceability Analysis of Water Delivery Systems," edited by M. Grigoriu, 3/6/89, (PB90-
127424, A03, MF-A01).
NCEER-89-0024 "Shaking Table Study of a 1/5 Scale Steel Frame Composed of Tapered Members," by K.C. Chang, J.S.
Hwang and G.C. Lee, 9118/89, (PB90-160169, A04, MF-A01).
Formerly the National Center for Earthquake Engineering Research 98

NCEER-89-0025 "DYNAID: A Computer Program for Nonlinear Seismic Site Response Analysis - Technical
Documentation," by Jean H. Prevost, 9114/89, (PB90-161944, A07, MF-AO1). This report is available only
NCEER-89-0026 "1:4 Scale Model Studies ofActive Tendon Systems and Active Mass Dampers for Aseismic Protection," by
AM. Reinhorn, T.T. Soong, R.C. Lin, Y.P. Yang, Y. Fukao, H. Abe and M. Nakai, 9115/89, (PB90-
173246, AlO, MF-A02). This report is available only through NTIS (see address given above).
NCEER-89-0027 "Scattering ofWaves by Inclusions in a Nonhomogeneous Elastic Half Space Solved by Boundary Element
Methods," by P.K. Hadley, A Askar and AS. Cakmak, 6115/89, (PB90-145699, A07, MF-A01).
NCEER-89-0028 "Statistical Evaluation ofDeflection Amplification Factors for Reinforced Concrete Structures," by H.H.M.
Hwang, J-w. JawandAL. Ch'ng, 8/31/89, (PB90-164633, A05, MF-AOl).
NCEER-89-0029 "Bedrock Accelerations in Memphis Area Due to Large New Madrid Earthquakes," by H.H.M. Hwang,
C.H.S. Chen and G. Yu, IIn189, (PB90-162330, A04, MF-AOl).
NCEER-89-0030 "Seismic Behavior and Response Sensitivity of Secondary Structural Systems," by Y.Q. Chen and T.T.
Soong, 10/23/89, (PB90-164658, A08, MF-AO1).
NCEER-89-0031 "Random Vibration and Reliability Analysis of Primary-Secondary Structural Systems," by Y. Ibrahim, M.
Grigoriu and T.T. Soong, 11110/89, (PB90-16l951, A04, MF-A01).
NCEER-89-0032 "Proceedings from the Second U.S. - Japan Workshop on Liquefaction, Large Ground Deformation and
Their Effects on Lifelines, September 26-29, 1989," Edited by T.D. O'Rourke and M. Hamada, 1211/89,
(PB90-209388, A22, MF-A03).
NCEER-89-0033 "Deterministic Model for Seismic Damage Evaluation of Reinforced Concrete Structures," by IM. Bracci,
AM. Reinhorn, J.B. Mander and S.K. Kunnath, 9/27/89, (PB91-108803, A06, MF-AOl).
NCEER-89-0034 "On the Relation Between Local and Global Damage Indices," by E. DiPasquale and AS. Cakmak, 8/15/89,
(PB90-173865, A05, MF-A01).
NCEER-89-0035 "Cyclic Undrained Behavior of Nonp1astic and Low Plasticity Silts," by Al Walker and H.E. Stewart,
7126/89, (PB90-183518, AI0, MF-AOl).
NCEER-89-0036 "Liquefaction Potential ofSurficial Deposits in the City ofBuffalo, New York," by M. Budhu, R. Giese and
1. Baumgra!s, 1117/89, (PB90-208455, A04, MF-AOl).
NCEER-89-0037 "A Deterministic Assessment of Effects of Ground Motion Incoherence," by AS. Veletsos and Y. Tang,
7115/89, (PB90-164294, A03, MF-AOl).
NCEER-89-0038 "Workshop on Ground Motion Parameters for Seismic Hazard Mapping," July 17-18, 1989, edited by R.V.
Whitman, 12/1189, (PB90-173923, A04, MF-AOl).
NCEER-89-0039 "Seismic Effects on Elevated Transit Lines of the New York City Transit Authority," by C.J. Costantino,
C.A. Miller and E. Heymsfield, 12/26/89, (PB90-207887, A06, MF-AOl).
NCEER-89-0040 "Centrifugal Modeling of Dynamic Soil-Structure Interaction,'i by K. Weissman, Supervised by IH.
Prevost, 5110/89, (PB90-207879, A07, MF-AOI).
NCEER-89-0041 "Linearized Identification of Buildings With Cores for Seismic Vulnerability Assessment," by I-K. Ho and
AE. Aktan, 1111/89, (PB90-251943, A07, MF-AOl).
NCEER-90-0001 "Geotechnical and Lifeline Aspects of the October 17, 1989 Lorna Prieta Earthquake in San Francisco," by
T.D. O'Rourke, H.E. Stewart, F.T. Blackburn and T.S. Dickerman, 1190, (PB90-208596, ADS, MF-AOl).

NCEER-90-0002 ''Nonnonna1 Secondary Response Due to Yielding in a Primary Structure," by D.C.K. Chen and L.D. Lutes,
2/28/90, (pB90-251976, A07, MF-AOl).
NCEER-90-0003 "Earthquake Education Materials for Grades K-12," by K.E.K. Ross, 4/16/90, (PB9l-25l984, A05, MF-
A05). This report has been replaced by NCEER-92-0018.
NCEER-90-0004 "Catalog of Strong Motion Stations in Eastern North America," by R.W. Busby, 4/3/90, (PB90-25l984,
AOS, MF-AOl).
NCEER-90-0005 "NCEER Strong-Motion Data Base: A User Manual for the GeoBase Release (Version 1.0 for the Sun3),"
by P. Friberg and K. Jacob, 3/31/90 (PB90-258062, A04, MF-A01).
NCEER-90-0006 "Seismic Hazard Along a Crude Oil Pipeline in the Event ofan 1811-1812 Type New Madrid Earthquake,"
by H.H.M Hwang and C-H.S. Chen, 4116/90, (PB90-258054, A04, MF-A01).
NCEER-90-0007 "Site-Specific Response Spectra for Memphis Sheahan Pumping Station," by H.H.M Hwang and C.S. Lee,
5/15/90, (pB91-l08811,AOS, MF-A01).
NCEER-90-0008 "Pilot Study on Seismic Vulnerability of Crude Oil Transmission Systems," by T. Ariman, R. Dobry, M.
Grigoriu, F. Kozin, M. O'Rourke, T. O'Rourke and M. Shinozuka, 5/25190, (pB91-108837, A06, MF-A01).
NCEER-90-0009 "A Program to Generate Site Dependent Time Histories: EQGEN," by G.w. Ellis, M. Srinivasan and AS.
Cakmak, 1130/90, (PB91-108829, A04, MF-AOl).
NCEER-90-001O "Active Isolation for Seismic Protection of Operating Rooms," by ME. Talbott, Supervised by M
Shinozuka, 6/8/9, (PB91-110205, A05, MF-AOl).
NCEER-90-0011 "Program LlNEARlD for Identification of Linear Structural Dynamic Systems," by C-B. Yun and M.
Shinozuka, 6125190, (pB91-110312, A08, MF-A01).
NCEER-90-0012 "Two-Dimensional Two-Phase Elasto-Plastic Seismic Response of Earth Dams," by AN. Yiagos,
Supervised by lH. Prevost, 6/20/90, (PB91-110197, A13, MF-A02).
NCEER-90-0013 "Secondary Systems in Base-Isolated Structures: Experimental fuvestigation, Stochastic Response and
Stochastic Sensitivity," by G.D. Manolis, G. Juhn, M.C. Constantinou and AM. Reinhorn, 711/90, (pB91-
110320, A08, MF-A01).
NCEER-90-0014 "Seismic Behavior of Lightly-Reinforced Concrete Column and Beam-Column Joint Details," by S.P.
Pessiki, C.H. Conley, P. Gergely and R.N. White, 8/22/90, (PB91-108795, All, MF-A02).
NCEER-90-0015 "Two Hybrid Control Systems for Building Structures Under Strong Earthquakes," by IN. Yang and A
Danie1ians, 6/29/90, (PB91-125393, A04, MF-AOI).
NCEER-90-0016 "fustantaneous Optimal Control with Acceleration and Velocity Feedback," by IN. Yang and Z. Li,
6/29190, (pB9l-l2540l, A03, MF-AOl).
NCEER-90-00l7 "Reconnaissance Report on the Northern Iran Earthquake of June 21, 1990," by M. Mehrain, 10/4/90,
(PB91-125377, A03, MF-AOl).
NCEER-90-00l8 "Evaluation ofLiquefaction Potential in Memphis and Shelby County," by T.S. Chang, P.S. Tang, C.S. Lee
and H. Hwang, 8110/90, (pB9l-125427, A09, MF-AOl).
NCEER-90-0019 "Experimental and Analytical Study of a Combined Sliding Disc Bearing and Helical Steel Spring Isolation
System," by MC. Constantinou, AS. Mokha and AM. Reinhorn, 10/4/90, (pB91-125385, A06, MF-AOl).
This report is available only through NTIS (see address given above).
Formerlythe National Centerfor Earthquake Engineering Research 100

NCEER-90-0020 "Experimental Study and Analytical Prediction ofEarthquake Response ofa Sliding Isolation System with a
Spherical Surface," by AS. Mokha, M.C. Constantinou and AM. Reinhom, 10/11/90, (PB91-1254l9, A05,
MF-A01).
NCEER-90-002l "Dynamic Interaction Factors for Floating Pile Groups," by G. Gazetas, K Fan, A Kaynia and E. Kausel,
9/10/90, (pB9l-17038l, A05, MF-A01).
NCEER-90-0022 "Evaluation of Seismic Damage Indices for Reinforced Concrete Structures," by S. Rodriguez-Gomez and
AS. Cakmak, 9/30/90, PB9l-l71322, A06, MF-A01).
NCEER-90-0023 "Study of Site Response at a Selected Memphis Site," by H. Desai, S. Ahmad, E.S. Gazetas and M.R. Oh,
10/11/90, (PB9l-l96857, A03, MF-A01).
NCEER-90-0024 "A User's Guide to Strongmo: Version 1.0 of NCEER's Strong-Motion Data Access Tool for PCs and
Terminals," by PA Friberg and CAT. Susch, 11/15/90, (PB9l-17l272, A03, MF-A01).
NCEER-90-0025 "A Three-Dimensional Analytical Study of Spatial Variability of Seismic Ground Motions," by L-L. Hong
and AH.-S. Ang, 10/30/90, (PB9l-l70399, A09, MF-A01).
NCEER-90-0026 "MUMOID User's Guide - A Program for the Identification of Modal Parameters," by S. Rodriguez-Gomez
and E. DiPasquale, 9/30/90, (PB9l-17l298, A04, MF-A01).
NCEER-90-0027 "SARCF-II User's Guide - Seismic Analysis ofReinforced Concrete Frames," by S. Rodriguez-Gomez, Y.S.
Chung and C. Meyer, 9/30/90, (PB9l-171280, A05, MF-A01).
NCEER-90-0028 "Viscous Dampers: Testing, Modeling and Application in Vibration and Seismic Isolation," by N. Makris
and M.C. Constantinou, 12/20/90 (PB9l-l90561, A06, MF-A01).
NCEER-90-0029 "Soil Effects on Earthquake Ground Motions in the Memphis Area," by H. Hwang, C.S. Lee, KW. Ng and
T.S. Chang, 8/2/90, (PB9l-19075l, A05, MF-A01).
NCEER-91-0001 "Proceedings from the Third Japan-U.S. Workshop on Earthquake Resistant Design of Lifeline Facilities
and Countermeasures for Soil Liquefaction, December 17-19, 1990," edited by T.D. O'Rourke and M.
Hamada, 2/1/91, (PB9l-179259, A99, MF-A04).
NCEER-91-0002 "Physical Space Solutions of Non-Proportionally Damped Systems," by M. Tong, Z. Liang and G.C. Lee,
1115/91, (PB91-179242, A04, MF-A01).
NCEER-91-0003 "Seismic Response of Single Piles and Pile Groups," by K Fan and G. Gazetas, 1110/91, (PB92-174994,
A04, MF-A01).
NCEER-91-0004 "Damping of Structures: Part 1 - Theory of Complex Damping," by Z. Liang and G. Lee, 10/10/91, (PB92-
197235, A12, MF-A03).
NCEER-91-0005 "3D-BASIS - Nonlinear Dynamic Analysis of Three Dimensional Base Isolated Structures: Part II," by S.
Nagarajaiah, AM. Reinhom and M.C. Constantinou, 2/28/91, (PB9l-l90553, A07, MF-A01). This report
has been replaced by NCEER-93-0011.
NCEER-91-0006 "A Multidimensional Hysteretic Model for Plasticity Deforming Metals in Energy Absorbing Devices," by
E.J. Graesser and FA Cozzarelli, 4/9/91, (PB92-108364, A04, MF-A01).
NCEER-91-0007 "A Framework for Customizable Knowledge-Based Expert Systems with an Application to a KBES for
Evaluating the Seismic Resistance of Existing Buildings," by E.G. Ibarra-Anaya and S.J. Fenves, 4/9/91,
(PB91-210930, A08, MF-A01).

NCEER-91-0008 "Nonlinear Analysis of Steel Frames with Semi-Rigid Connections Using the Capacity Spectrwu Method,"
by G.G. Deierlein, S-H. Hsieh, Y-l Shen and IF. Abel, 7/2/91, (PB92-113828, A05, MF-A01).
NCEER-9I-0009 "Earthquake Education Materials for Grades K-12," by K.E.K. Ross, 4/30/91, (pB91-212142, A06, MF-
AOI). This report has been replaced by NCEER-92-0018.
NCEER-9I-001O "Phase Wave Velocities and Displacement Phase Differences in a Hannonically Oscillating Pile," by N.
Makris and G. Gazetas, 7/8/91, (PB92-108356, A04, MF-AOl).
NCEER-91-0011 "Dynamic Characteristics of a Full-Size Five-Story Steel Structure and a 2/5 Scale Model," by KC. Chang,
G.C. Yao, G.C. Lee, D.S. Hao and Y.C. Yeh," 7/2191, (PB93-116648, A06, MF-A02).
NCEER-91-0012 "Seismic Response of a 2/5 Scale Steel Structure with Added Viscoelastic Dampers," by KC. Chang, T.T.
Soong, S-T. Oh and M.L. Lai, 5117/91, (PB92-110816, A05, MF-A01).
NCEER-91-0013 "Earthquake Response of Retaining Walls; Full-Scale Testing and Computational Modeling," by S.
Alampalli and A-W.M. Elgamal, 6/20/91, to be published.
NCEER-91-0014 "3D-BASlS-M: Nonlinear Dynamic Analysis of Multiple Building Base Isolated Structures," by P.C.
Tsopelas, S. Nagarajaiah, M.C. Constantinou and AM. Reinhorn, 5128/91, (PB92-113885, A09, MF-A02).
NCEER-91-0015 "Evaluation ofSEAOC Design Requirements for Sliding Isolated Structures," by D. Theodossiou and M.C.
Constantinou, 6110/91, (PB92-114602, All, MF-A03).
NCEER-91-0016 "Closed-Loop Modal Testing of a 27-Story Reinforced Concrete Flat Plate-Core Building," by H.R.
Sornaprasad, T. Toksoy, H. Yoshiyuki and AE. Aktan, 7115/91, (PB92-129980, A07, MF-A02).
NCEER-91-0017 "Shake Table Test ofa 116 Scale Two-Story Lightly Reinforced Concrete Building," by AG. El-Attar, R.N.
White and P. Gergely, 2128/91, (PB92-222447, A06, MF-A02).
NCEER-91-0018 "Shake Table Test of a 1/8 Scale Three-Story Lightly Reinforced Concrete Building," by AG. EI-Attar,
R.N. White and P. Gergely, 2/28/91, (pB93-116630, A08, MF-A(2).
NCEER-91-0019 "Transfer Functions for Rigid Rectangular Foundations," by AS. Veletsos, AM. Prasad and W.H. Wu,
7/31191, to be published.
NCEER-91-0020 "Hybrid Control ofSeismic-Excited Nonlinear and Inelastic Structural Systems," by IN. Yang, Z. Li and A
Danielians, 811191, (PB92-143171, A06, MF-A02).
NCEER-91-0021 "The NCEER-91 Earthquake Catalog: Improved Intensity-Based Magnitudes and Recurrence Relations for
U.S. Earthquakes East of New Madrid," by L. Seeber and lG. Armbruster, 8/28/91, (PB92-176742, A06,
MF-A02).
NCEER-91-0022 "Proceedings from the Implementation of Earthquake Planning and Education in Schools: The Need for
Change - The Roles ofthe Changernakers," by KE.K Ross and F. Winslow, 7/23/91, (PB92-129998, A12,
MF-A03).
NCEER-91-0023 "A Study of Reliability-Based Criteria for Seismic Design of Reinforced Concrete Frame Buildings," by
H.H.M. Hwang and H-M. Hsu, 8110/91, (PB92-140235, A09, MF-A02).
NCEER-91-0024 "Experimental Verification ofa Number of Structural System Identification Algorithms," by R.G. Ghanem,
H. Gavin and M. Shinozuka, 9118/91, (PB92-176577, A18, MF-A04).
NCEER-91-0025 "Probabilistic Evaluation of Liquefaction Potential," by H.H.M. Hwang and C.S. Lee," 11125/91, (pB92-
143429, A05, MF-A01).

NCEER-91-0026 "fustantaneous Optimal Control for Linear, Nonlinear and Hysteretic Structures - Stable Controllers," by
IN. Yang and Z. Li, 11/15191, (PB92-163807, A04, MF-A01).
NCEER-9l-0027 "Experimental and Theoretical Study of a Sliding Isolation System for Bridges," by M.C. Constantinou, A
Kartoum, AM. Reinhorn and P. Bradford, 11115/91, (PB92-l76973, AlO, MF-A03).
NCEER-92-0001 "Case Studies ofLiquefaction and Lifeline Performance During Past Earthquakes, Volume 1: Japanese Case
Studies," Edited by M. Hamada and T. O'Rourke, 2117/92, (PB92-l97243, A18, MF-A04).
NCEER-92-0002 "Case Studies ofLiquefaction and Lifeline Performance During Past Earthquakes, Volume 2: United States
Case Studies," Edited by T. O'Rourke and M. Hamada, 2117/92, (pB92-l97250, A20, MF-A04).
NCEER-92-0003 "Issues in Earthquake Education," Edited by K. Ross, 2/3/92, (PB92-222389, A07, MF-A02).
NCEER-92-0004 "Proceedings from the First U.S. - Japan Workshop on Earthquake Protective Systems for Bridges," Edited
by I.G. Buckle, 2/4/92, (PB94-l42239, A99, MF-A06).
NCEER-92-0005 "Seismic Ground Motion from a Haskell-Type Source in a Multiple-Layered Half-Space," AP. Theoharis,
G. Deodatis and M. Shinozuka, 112/92, to be published.
NCEER-92-0006 "Proceedings from the Site Effects Workshop," Edited by R. Whitman, 2/29/92, (PB92-197201, A04, MF-
AOl).
NCEER-92-0007 "Engineering Evaluation of Permanent Ground Deformations Due to Seismically-fuduced Liquefaction," by
M.H. Baziar, R. Dobry and A-W.M. Elgamal, 3/24/92, (PB92-222421, A13, MF-A03).
NCEER-92-0008 "A Procedure for the Seismic Evaluation of Buildings in the Central and Eastern United States," by C.D.
Poland and J.O. Malley, 4/2/92, (PB92-222439, A20, MF-A04).
NCEER-92-0009 "Experimental and Analytical Study of a Hybrid Isolation System Using Friction Controllable Sliding
Bearings," by M.Q. Feng, S. Fujii and M. Shinozuka, 5115/92, (PB93-150282, A06, MF-A02).
NCEER-92-001O "Seismic Resistance of Slab-Column Connections in Existing Non-Ductile Flat-Plate Buildings," by Al
Durrani and Y. Du, 5118/92, (pB93-ll6812, A06, MF-A02).
NCEER-92-0011 "The Hysteretic and Dynamic Behavior ofBrick Masonry Walls Upgraded by Ferrocement Coatings Under
Cyclic Loading and Strong Simulated Ground Motion," by H. Lee and S.P. Prawel, 5111192, to be
published.
NCEER-92-0012 "Study of Wire Rope Systems for Seismic Protection of Equipment in Buildings," by G.F. Demetriades,
M.C. Constantinou and AM. Reinhorn, 5/20/92, (pB93-ll6655, ~08, MF-A02).
NCEER-92-0013 "Shape Memory Structural Dampers: Material Properties, Design and Seismic Testing," by P.R. Witting
and F.A. Cozzarelli, 5/26/92, (PB93-l16663, A05, MF-AOl).
NCEER-92-0014 "Longitudinal Permanent Ground Deformation Effects on Buried Continuous Pipelines," by M.l O'Rourke,
and C. Nordberg, 6115/92, (PB93-11667l, A08, MF-A02).
NCEER-92-0015 "A Simulation Method for Stationary Gaussian Random Functions Based on the Sampling Theorem," by M.
Grigoriu and S. Balopoulou, 6111/92, (pB93-127496, A05, MF-A01).
NCEER-92-0016 "Gravity-Load-Designed Reinforced Concrete Buildings: Seismic Evaluation of Existing Construction and
Detailing Strategies for Improved Seismic Resistance," by G.w. Hoffmann, S.K. Kunnath, AM. Reinhorn
and lB. Mander, 7/15/92, (PB94-l42007, A08, MF-A02).

NCEER-92-00l7 "Observations on Water System and Pipeline Perfonnance in the Limon Area of Costa Rica Due to the
April 22, 1991 Earthquake," byM. O'Rourke and D. Ballantyne, 6/30/92, (pB93-l268ll, A06, MF-A02).
NCEER-92-00l8 "Fourth Edition of Earthquake Education Materials for Grades K-12," Edited by K.E.K. Ross, 8110/92,
(PB93-114023, A07, MF-A02).
NCEER-92-0019 "Proceedings from the Fourth Japan-U.S. Workshop on Earthquake Resistant Design of Lifeline Facilities
and Countenneasures for Soil Liquefaction," Edited by M. Hamada and T.D. O'Rourke, 8/12/92, (PB93-
163939, A99, MF-Ell).
NCEER-92-0020 "Active Bracing System: A Full Scale hnplementation of Active Control," by AM. Reinhorn, T.T. Soong,
R.C. Lin, M.A. Riley, Y.P. Wang, S. Aizawa and M. Higashino, 8/14/92, (PB93-127512, A06, MF-A02).
NCEER-92-002l "Empirical Analysis of Horizontal Ground Displacement Generated by Liquefaction-Induced Lateral
Spreads," by S.F. Bartlett and T.L. Youd, 8117/92, (PB93-18824l, A06, MF-A02).
NCEER-92-0022 "IDARC Version 3.0: Inelastic Damage Analysis of Reinforced Concrete Structures," by S.K. Kunnath,
AM. Reinhom and R.F. Lobo, 8/31192, (PB93-227502, A07, MF-A02).
NCEER-92-0023 "A Semi-Empirical Analysis of Strong-Motion Peaks in Tenns of Seismic Source, Propagation Path and
Local Site Conditions, by M. Kamiyama, M.J. O'Rourke and R. Flores-Berrones, 9/9/92, (pB93-150266,
A08, MF-A02).
NCEER-92-0024 "Seismic Behavior of Reinforced Concrete Frame Structures with Nonductile Details, Part I: Sununary of
Experimental Findings of Full Scale Beam-Column Joint Tests," by A Beres, R.N. White and P. Gergely,
9/30/92, (PB93-227783, A05, MF-A01).
NCEER-92-0025 "Experimental Results of Repaired and Retrofitted Beam-Column Joint Tests in Lightly Reinforced
Concrete Frame Buildings," by A Beres, S. EI-Borgi, R.N. White'and P. Gergely, lO/29/92, (PB93-227791,
A05, MF-A01).
NCEER-92-0026 "A Generalization ofOptimal Control Theory: Linear and Nonlinear Structures," by J.N. Yang, Z. Li and S.
Vongchavalitkul, 11/2/92, (PB93-18862l, A05, MF-A01).
NCEER-92-0027 "Seismic Resistance of Reinforced Concrete Frame Structures Designed Only for Gravity Loads: Part I -
Design and Properties of a One-Third Scale Model Structure," by J.M. Bracci, AM. Reinhom and J.B.
Mander, 1211/92, (PB94-104502, A08, MF-A02).
NCEER-92-0028 "Seismic Resistance of Reinforced Concrete Frame Structures Designed Only for Gravity Loads: Part II -
Experimental Perfonnance of Subassemblages," by 1.E. Aycardi, J.B. Mander and AM. Reinhom, 1211/92,
(PB94-1045lO, A08, MF-A02).
NCEER-92-0029 "Seismic Resistance of Reinforced Concrete Frame Structures Designed Only for Gravity Loads: Part III -
Experimental Perfonnance and Analytical Study ofa Structural Model," by J.M. Bracci, AM. Reinhom and
J.B. Mander, 12/1192, (PB93-227528, A09, MF-A01).
NCEER-92-0030 "Evaluation of Seismic Retrofit of Reinforced Concrete Frame Structures: Part I - Experimental
Perfonnance of Retrofitted Subassemblages," by D. Choudhuri, J.B. Mander and AM. Reinhom, 12/8/92,
(PB93-198307, A07, MF-A02).
NCEER-92-0031 "Evaluation of Seismic Retrofit of Reinforced Concrete Frame Structures: Part II - Experimental
Perfonnance and Analytical Study of a Retrofitted Structural Model," by J.M. Bracci, AM. Reinhom and
J.B. Mander, 12/8/92, (PB93-198315, A09, MF-A03).
NCEER-92-0032 "Experimental and Analytical Investigation of Seismic Response of Structures with Supplemental Fluid
Viscous Dampers," by M.C. Constantinou and M.D. Symans, 12/21192, (PB93-191435, AlO, MF-A03).
This report is available only through NTIS (see address given above).

NCEER-92-0033 "Reconnaissance Report on the Cairo, Egypt Earthquake of October 12, 1992," by M Khater, 12/23/92,
(PB93-188621, A03, MF-AOl).
NCEER-92-0034 "Low-Level Dynamic Characteristics ofFour Tall Flat-Plate Buildings in New York City," by H. Gavin, S.
Yuan, J. Grossman, E. Pekelis and K Jacob, 12/28/92, (PB93-188217, A07, MF-A02).
NCEER-93-0001 "An Experimental Study on the Seismic Performance of Brick-Infilled Steel Frames With and Without
Retrofit," by J.B. Mander, B. Nair, K Wojtkowski and 1. Ma, 1I2?/93, (PB93-227510, A07, MF-A02).
NCEER-93-0002 "Social Accounting for Disaster Preparedness and Recovery Planning," by S. Cole, E. Pantoja and V. Razak,
2/22/93, (PB94-142114, A12, MF-A03).
NCEER-93-0003 "Assessment of 1991 NEHRP Provisions for Nonstructural Components and Recommended Revisions," by
T.T. Soong, G. Chen, Z. Wu, R-H. Zhang ~d M Grigoriu, 311193, (PB93-188639, A06, MF-A02).
NCEER-93-0004 "Evaluation of Static and Response Spectrum Analysis Procedures of SEAOCIUBC for Seismic Isolated
Structures," by CW. Winters and MC. Constantinou, 3/23/93, (PB93-198299, AlO, MF-A03).
NCEER-93-0005 "Earthquakes in the Northeast - Are We Ignoring the Hazard? A Workshop on Earthquake Science and
Safety for Educators," edited by KE.K Ross, 4/2/93, (PB94-103066, A09, MF-A02).
NCEER-93-0006 "Inelastic Response of Reinforced Concrete Structures with Viscoelastic Braces," by R.F. Lobo, J.M.
Bracci, KL. Shen, A.M. Reinhorn and T.T. Soong, 4/5193, (PB93-227486, A05, MF-A02).
NCEER-93-0007 "Seismic Testing of Installation Methods for Computers and Data Processing Equipment," by K Kosar,
T.T. Soong, KL. Shen, JA HoLung and YK Lin, 4112/93, (PB93-198299, A07, MF-A02).
NCEER-93-0008 "Retrofit ofReinforced Concrete Frames Using Added Dampers," by A. Reinhorn, M. Constantinou and C.
Li, to be published.
NCEER-93-0009 "Seismic Behavior and Design Guidelines for Steel Frame Structures with Added Viscoelastic Dampers,"
byKC. Chang, M.L. Lai, T.T. Soong, D.S. Hao and Y.C. Yeh, 511193, (PB94-141959, A07, MF-A02).
NCEER-93-001O "Seismic Performance of Shear-Critical Reinforced Concrete Bridge Piers," by J.B. Mander, S.M. Waheed,
M.TA Chaudhary and S.S. Chen, 5112/93, (PB93-227494, A08, MF-A02).
NCEER-93-0011 "3D-BASIS-TABS: Computer Program for Nonlinear Dynamic Analysis of Three Dimensional Base
Isolated Structures," by S. Nagarajaiah, C. Li, A.M. Reinhorn and MC. Constantinou, 8/2/93, (PB94-
141819, A09, MF-A02).
NCEER-93-0012 "Effects ofHydrocarbon Spills from an Oil Pipeline Break on Ground Water," by O.J. Helweg and H.H.M.
Hwang, 8/3/93, (PB94-141942, A06, MF-A02).
NCEER-93-0013 "Simplified Procedures for Seismic Design ofNonstructural Components and Assessment of Current Code
Provisions," by MP. Singh, L.E. Suarez, E.E. Matheu and G.O. Maldonado, 8/4/93, (PB94-141827, A09,
MF-A02).
NCEER-93-0014 "An Energy Approach to Seismic Analysis and Design of Secondary Systems," by G. Chen and T.T. Soong,
8/6/93, (PB94-142767, All, MF-A03).
NCEER-93-0015 "Proceedings from School Sites: Becoming Prepared for Earthquakes - Commemorating the Third
Anniversary of the Lorna Prieta Earthquake," Edited by F.E. Winslow and KE.K Ross, 8116/93, (PB94-
154275, A16, MF-A02).

NCEER-93-0016 "Reconnaissance Report ofDamage to Historic Monwnents in Cairo, Egypt Following the October 12, 1992
Dahshur Earthquake," by D. Sykora, D. Look, G. Croci, E. Karaesmen and E. Karaesmen, 8/19/93, (pB94-
142221, A08, MF-A02).
NCEER-93-0017 "The Island of Guam Earthquake of August 8, 1993," by S.W. Swan and S.K. Harris, 9/30/93, (PB94-
141843, A04, MF-A01).
NCEER-93-0018 "Engineering Aspects of the October 12, 1992 Egyptian Earthquake," by AW. Elgamal, M. Amer, K.
Adalier and A Abul-Fadl, lDnl93, (PB94-141983, A05, MF-A01).
NCEER-93-0019 "Development of an Earthquake Motion Simulator and its Application in Dynamic Centrifuge Testing,II by
I. Krstelj, Supervised by J.H. Prevost, 10/23/93, (PB94-181773, A-lO, MF-A03).
NCEER-93-0020 "NCEER-Taisei Corporation Research Program on Sliding Seismic Isolation Systems for Bridges:
Experimental and Analytical Study of a Friction Pendulwn System (FPS)," by M.C. Constantinou, P.
Tsopelas, Y-S. Kim and S. Okamoto, 1111/93, (PB94-142775, A08, MF-A02).
NCEER-93-0021 "Finite Element Modeling of Elastomeric Seismic Isolation Bearings," by L.I Billings, Supervised by R.
Shepherd, 11/8/93, to be published.
NCEER-93-D022 "Seismic Vulnerability ofEquipment in Critical Facilities: Life-Safety and Operational Consequences," by
K. Porter, G.S. Johnson, M.M. Zadeh, C. Scawthorn and S. Eder, 11124/93, (PB94-181765, A16, MF-A03).
NCEER-93-0023 "Hokkaido Nansei-oki, Japan Earthquake of July 12, 1993, by P.I. Yanev and C.R. Scawthorn, 12/23/93,
(PB94-181500, A07, MF-A01).
NCEER-94-D001 "An Evaluation of Seismic Serviceability of Water Supply Networks with Application to the San Francisco
Auxiliary Water Supply System," by I. Markov, Supervised by M. Grigoriu and T. O'Rourke, 1/21/94,
(PB94-2040I3, A07, MF-A02).
NCEER-94-D002 "NCEER-Taisei Corporation Research Program on Sliding Seismic Isolation Systems for Bridges:
Experimental and Analytical Study of Systems Consisting of Sliding Bearings, Rubber Restoring Force
Devices and Fluid Dampers," Volwnes I and II, by P. Tsopelas, S. Okamoto, M.C. Constantinou, D. Ozaki
and S. Fujii, 2/4/94, (PB94-181740, A09, MF-A02 and PB94-181757, A12, MF-A03).
NCEER-94-0003 "A Markov Model for Local and Global Damage Indices in Seismic Analysis," by S. Rahman and M.
Grigoriu, 2118/94, (PB94-206000, A12, MF-A03). .
NCEER-94-0004 "Proceedings from the NCEER Workshop on Seismic Response of Masonry Infills," edited by D.P. Abrams,
311/94, (PB94-180783, A07, MF-A02).
NCEER-94-D005 "The Northridge, California Earthquake of January 17, 1994: General Reconnaissance Report," edited by
J.D. Goltz, 3111194, (pB193943, AlD, MF-A03).
NCEER-94-0006 "Seismic Energy Based Fatigue Damage Analysis of Bridge Columns: Part I - Evaluation of Seismic
Capacity," by GA Chang and lB. Mander, 3/14/94, (PB94-219185, All, MF-A03).
NCEER-94-0007 "Seismic Isolation ofMulti-Story Frame Structures Using Spherical Sliding Isolation Systems," by T.M. Al-
Hussaini, VA Zayas and M.C. Constantinou, 3117/94, (PBl93745, A09, MF-A02).
NCEER-94-0008 "The Northridge, California Earthquake of January 17, 1994: Performance of Highway Bridges," edited by
I.G. Buckle, 3/24/94, (PB94-193851, A06, MF-A02).
NCEER-94-D009 "Proceedings of the Third U.S.-Japan Workshop on Earthquake Protective Systems for Bridges," edited by
I.G. Buckle and I. Friedland, 3/31194, (PB94-195815, A99, MF-A06).

NCEER-94-001O "3D-BASIS-ME: Computer Program for Nonlinear Dynamic Analysis of Seismically Isolated Single and
Multiple Structures and Liquid Storage Tanks," by P.C. Tsopelas, M.C. Constantinou and AM. Reinhom,
4112/94, (pB94-204922, A09, MF-A02).
NCEER-94-0011 "The Northridge, California Earthquake of January 17, 1994: Performance of Gas Transmission Pipelines,"
by T.D. O'Rourke and M.C. Palmer, 5116/94, (PB94-204989, A05, MF-A01).
NCEER-94-0012 "Feasibility Study of Replacement Procedures and Earthquake Performance Related to Gas Transmission
Pipelines," by T.D. O'Rourke and M.C. Palmer, 5/25/94, (PB94-206638, A09, MF-A02).
NCEER-94-00l3 "Seismic Energy Based Fatigue Damage Analysis of Bridge Columns: Part II - Evaluation of Seismic
Demand," by G.A. Chang and J.B. Mander, 611/94, (PB95-18106, A08, MF-A02).
Experimental and Analytical Study of a System Consisting of Sliding Bearings and Fluid Restoring
ForcelDamping Devices," by P. Tsopelas and M.C. Constantinou, 6/13/94, (pB94-219l44, AlO, MF-A03).
NCEER-94-0015 "Generation ofHazard-Consistent Fragility Curves for Seismic Loss Estimation Studies," by H. Hwang and
J-R. Huo, 6114/94, (PB95-l81996, A09, MF-A02).
NCEER-94-0016 "Seismic Study of Building Frames with Added Energy-Absorbing Devices," by W.S. Pong, C.S. Tsai and
G.C. Lee, 6/20/94, (PB94-219136, AlO, A03).
NCEER-94-0017 "Sliding Mode Control for Seismic-Excited Linear and Nonlinear Civil Engineering Structures," by J. Yang,
J. Wu, A Agrawal and Z. Li, 6/21194, (PB95-138483, A06, MF-A02).
NCEER-94-0018 "3D-BASIS-TABS Version 2.0: Computer Program for Nonlinear Dynamic Analysis of Three Dimensional
Base Isolated Structures," by AM. Reinhom, S. Nagarajaiah, M.C. Constantinou, P. Tsopelas and R. Li,
6/22/94, (PB95-l82176, A08, MF-A02).
NCEER-94-00l9 "Proceedings of the International Workshop on Civil Infrastructure Systems: Application of Intelligent
Systems and Advanced Materials on Bridge Systems," Edited by G.C. Lee and K.C. Chang, 7118/94,
(PB95-252474, A20, MF-A04).
NCEER-94-0020 "Study ofSeismic Isolation Systems for Computer Floors," by V. Lambrou and M.C. Constantinou, 7119/94,
(PB95-138533, AlO, MF-A03).
NCEER-94-002l "Proceedings of the U.S.-Italian Workshop on Guidelines for Seismic Evaluation and Rehabilitation of
Umeinforced Masonry Buildings," Edited by D.P. Abrams and G.M. Calvi, 7/20/94, (PB95-l38749, Al3,
MF-A03).
Experimental and Analytical Study of a System Consisting of Lubricated PTFE Sliding Bearings and Mild
Steel Dampers," by P. Tsopelas and M.C. Constantinou, 7/22/94, (PB95-182184, A08, MF-A02).
NCEER-94-0023 "Development of Reliability-Based Design Criteria for Buildings Under Seismic Load," by Y.K. Wen, H.
Hwang and M. Shinozuka, 8/1/94, (PB95-211934, A08, MF-A02):
NCEER-94-0024 "Experimental Verification of Acceleration Feedback Control Strategies for an Active Tendon System," by
S.J. Dyke, B.F. Spencer, Jr., P. Quast, M.K. Sain, D.C. Kaspari, Jr. and T.T. Soong, 8/29/94, (PB95-
212320, A05, MF-AOl).
NCEER-94-0025 "Seismic Retrofitting Manual for Highway Bridges," Edited by I.G. Buckle and I.F. Friedland, published by
the Federal Highway Administration (PB95-212676, A15, MF-A03).

NCEER-94-0026 "Proceedings from the Fifth U.S.-Japan Workshop on Earthquake Resistant Design of Lifeline Facilities
and COWltermeasures Against Soil Liquefaction," Edited by T:D. O'Rourke and M. Hamada, lln/94,
(pB95-220S02, A99, MF-EOS).
NCEER-95-0001 "Experimental and Analytical Investigation of Seismic Retrofit of Structures with Supplemental Damping:
Part 1 - Fluid Viscous Damping Devices," by AM. Reinhom, C. Li and M.C. Constantinou, 113/95, (pB95-
266599, A09, MF-A02).
NCEER-95-0002 ''Experimental and Analytical Study of Low-Cycle Fatigue Behavior of Semi-Rigid Top-And-Seat Angle
Connections," by G. Pekcan, J.B. Mander and S.S. Chen, 115195, (PB95-220042, A07, MF-A02).
NCEER-95-0003 "NCEER-ATC Joint Study on Fragility of Buildings," by T. Anagnos, C. Rojahn and AS. Kiremidjian,
1120/95, (pB95-220026, A06, MF-A02).
NCEER-95-0004 ''Nonlinear Control Algorithms for Peak Response Reduction," by Z. Wu, T.T. Soong, V. Gattulli and RC.
Lin, 2116/95, (PB95-220349,A05, MF-AOI).
NCEER-95-0005 ''Pipeline Replacement Feasibility Study: A Methodology for Minimizing Seismic and Corrosion Risks to
UndergroWld Natural Gas Pipelines," by RT. Eguchi, H.A Seligson and D.G. Honegger, 3/2/95, (pB95-
252326, A06, MF-A02).
NCEER-95-0006 "Evaluation of Seismic Performance of an ll-Story Frame Building During the 1994 Northridge
Earthquake," by F. Naeim, R DiSulio, K. Benuska, A Reinhorn and C. Li, to be published.
NCEER-95-0007 "Prioritization of Bridges for Seismic Retrofitting," by N. Basoz and AS. Kiremidjian, 4/24/95, (pB95-
252300, A08, MF-A02).
NCEER-95-000S "Method for Developing Motion Damage Relationships for Reinforced Concrete Frames," by A Singhal
and AS. Kiremidjian, 5111195, (PB95-266607, A06, MF-A02).
Part IT - Friction Devices," by C. Li and AM. Reinhorn, 7/6/95, (PB96-l28087, All, MF-A03).
NCEER-95-001O "Experimental Performance and Analytical Study of a Non-Ductile Reinforced Concrete Frame Structure
Retrofitted with Elastomeric Spring Dampers," by G. Pekcan, J.B. Mander and S.S. Chen, 7114/95, (PB96-
137161, A08, MF-A02).
NCEER-95-00Il "Development and Experimental Study of Semi-Active Fluid Damping Devices for Seismic Protection of
Structures," by M.D. Symans and M.C. Constantinou, 8/3/95, (PB96-136940, A23, MF-A04).
NCEER-95-0012 "Real-Time Structural Parameter Modification (RSPM): Development of Innervated Structures," by Z.
Liang, M. Tong and G.C. Lee, 4111/95, (PB96-137153, A06, MF-AOl).
Part III - Viscous Damping Walls," by AM. Reinhorn and C. Li, 1011195, (PB96-l76409, All, MF-A03).
NCEER-95-00l4 "Seismic Fragility Analysis of Equipment and Structures in a Memphis Electric Substation," by J-R Huo
and H.H.M. Hwang, (PB96-12S087, A09, MF-A02), SI10/95.
NCEER-95-00l5 "The Hanshin-Awaji Earthquake of January 17, 1995: Performan~e of Lifelines," Edited by M. Shinozuka,
1113/95, (PB96-176383, A15, MF-A03).
NCEER-95-00l6 "Highway Culvert Performance During Earthquakes," by T.L. Youd and C.J. Beckman, available as
NCEER-96-0015.

NCEER-95-0017 "The Hanshin-Awaji Earthquake of January 17, 1995: Performance of Highway Bridges," Edited by I.G.
Buckle, 12/1/95, to be published.
NCEER-95-0018 "Modeling ofMasonry Infill Panels for Structural Analysis," by AM. Reinhorn, A Madan, RE. Valles, Y.
Reichmann and J.B. Mander, 12/8/95.
NCEER-95-0019 "Optimal Polynomial Control for Linear and Nonlinear Structures," by AK. Agrawal and J.N. Yang,
12111195, (pB96-168737, A07, MF-A02).
NCEER-95-0020 "Retrofit of Non-Ductile Reinforced Concrete Frames Using Friction Dampers," by RS. Rao, P. Gergely
and RN. White, 12/22/95, (PB97-133508, AlO, MF-A02).
NCEER-95-0021 "Parametric Results for Seismic Response of Pile-Supported Bridge Bents," by G. Mylonakis, A Nikolaou
and G. Gazetas, 12/22/95, (PB97-100242, A12, MF-A03).
NCEER-95-0022 "Kinematic Bending Moments in Seismically Stressed Piles," by A Nikolaou, G. Mylonakis and G.
Gazetas, 12/23/95.
NCEER-96-0001 "Dynamic Response ofUnreinforced Masonry Buildings with Flexible Diaphragms," by AC. Costley and
D.P. Abrams," lOI10/96.
NCEER-96-0002 "State ofthe Art Review: Foundations and Retaining Structures," by I. Po Lam, to be published.
NCEER-96-0003 "Ductility of Rectangular Reinforced Concrete Bridge Columns with Moderate Confmement," by N.
Wehbe, M. Saiidi, D. Sanders and B. Douglas, Iln196, (PB97-133557, A06, MF-A02).
NCEER-96-0004 "Proceedings of the Long-Span Bridge Seismic Research Workshop," edited by I.G. Buckle and I.M.
Friedland, to be published.
NCEER-96-0005 "Establish Representative Pier Types for Comprehensive Study: Eastern United States," by J. Kulicki and
Z. Prucz, 5/28/96, (PB98-119217, A07, MF-A02).
NCEER-96-0006 "Establish Representative Pier Types for Comprehensive Study: Western United States," by R Imbsen,
RA Schamber and T.A. Osterkamp, 5/28/96, (PB98-118607, A07, MF-A02).
NCEER-96-0007 "Nonlinear Control Techniques for Dynamical Systems with Uncertain Parameters," by RG. Ghanem and
M.I. Bujakov, 5/27/96, (PB97-100259, A17, MF-A03).
NCEER-96-0008 "Seismic Evaluation of a 30-Year Old Non-Ductile Highway Bridge Pier and Its Retrofit," by lB. Mander,
B. Mahmoodzadegan, S. Bhadra and S.S. Chen, 5/31196.
NCEER-96-0009 "Seismic Performance of a Model Reinforced Concrete Bridge Pier Before and After Retrofit," by lB.
Mander, lH. Kim and C.A. Ligozio, 5/31/96.
NCEER-96-00lO "IDARC2D Version 4.0: A Computer Program for the Inelastic Damage Analysis of Buildings," by RE.
Valles, AM. Reinhorn, S.K. Kunnath, C. Li and A Madan, 6/3/96, (pB97-100234, A17, MF-A03).
NCEER-96-0011 "Estimation of the Economic Impact of Multiple Lifeline Disruption: Memphis Light, Gas and Water
Division Case Study," by S.E. Chang, H.A. Seligson and RT. Eguchi, 8/16/96, (PB97-133490, All, MF-
A03).
NCEER-96-0012 "Proceedings from the Sixth Japan-U.S. Workshop on Earthquake Resistant Design of Lifeline Facilities
and Countermeasures Against Soil Liquefaction, Edited by M. Hamada and T. O'Rourke, 9111196, (PB97-
133581, A99, MF-A06).

NCEER-96-0013 "Chemical Hazards, Mitigation and Preparedness in Areas of High Seismic Risk: A Methodology for
Estimating the Risk ofPost-Earthquake Hazardous Materials Release," by H.A Seligson, RT. Eguchi, K.J.
Tierney and K. Richmond, Ilnl96.
NCEER-96-00l4 ''Response of Steel Bridge Bearings to Reversed Cyclic Loading," by J.B. Mander, D-K Kim, S.S. Chen
and G.J. Premus, 11113/96, (PB97-140735, A12, MF-A03).
NCEER-96-00l5 "Highway Culvert Performance During Past Earthquakes," by T.L. Youd and C.J. Beckman, 11/25/96,
(pB97-l33532, A06, MF-AOl).
NCEER-97-000l "Evaluation, Prevention and Mitigation of Pounding Effects in Building Structures," by RE. Valles and
AM Reinhom, 2/20/97, (PB97-159552, A14, MF-A03).
NCEER-97-0002 "Seismic Design Criteria for Bridges and Other Highway Structures," by C. Rojahn, R Mayes, D.G.
Anderson, J. Clark, J.H. Hom, R.V. Nutt and MJ. O'Rourke, 4/30/97, (PB97-194658, A06, MF-A03).
NCEER-97-0003 "Proceedings ofthe U.S.-Italian Workshop on Seismic Evaluation and Retrofit," Edited by D.P. Abrams and
G.M. Calvi, 3119/97, (PB97-l94666, A13, MF-A03).
NCEER-97-0004 "Investigation of Seismic Response of Buildings with Linear and Nonlinear Fluid Viscous Dampers," by
AA Seleemah and MC. Constantinou, 5/21197, (PB98-109002, A15, MF-A03).
NCEER-97-0005 "Proceedings ofthe Workshop on Earthquake Engineering Frontiers in Transportation Facilities," edited by
G.C. Lee and I.M Friedland, 8/29/97, (PB98-l28911, A25, MR-A04).
NCEER-97-0006 "Cumulative Seismic Damage of Reinforced Concrete Bridge Piers," by S.K. Kunnath, A EI-Bahy, A
Taylor and W. Stone, 9/2/97, (PB98-1088l4, All, MF-A03).
NCEER-97-0007 "Structural Details to Accommodate Seismic Movements of Highway Bridges and Retaining Walls," by
RA Imbsen, R.A Schamber, E. Thorkildsen, A Kartoum, B.T. Martin, T.N. Rosser and J.M. Kulicki,
9/3/97.
NCEER-97-0008 "A Method for Earthquake Motion-Damage Relationships with Application to Reinforced Concrete
Frames," by A Singhal and AS. Kiremidjian, 9110/97, (PB98-108988, Al3, MF-A03).
NCEER-97-0009 "Seismic Analysis and Design ofBridge Abutments Considering Sliding and Rotation," by K Fishman and
R Richards, Jr., 9115/97, (pB98-108897, A06, MF-A02).
NCEER-97-001O "Proceedings of the FHWAINCEER Workshop on the National Representation of Seismic Ground Motion
for New and Existing Highway Facilities," edited by I.M Friedland, M.S. Power and RL. Mayes, 9/22/97.
NCEER-97-00ll "Seismic Analysis for Design or Retrofit of Gravity Bridge Abutments," by KL. Fishman, R Richards, Jr.
and RC. Divito, 10/2/97, (pB98-l28937, A08, MF-A02).
NCEER-97-00l2 "Evaluation of Simplified Methods of Analysis for Yielding Structures," by P. Tsopelas, M.C.
Constantinou, C.A. Kircher and AS. Whittaker, 10/31197, (PB98~128929, AIO, MF-A03).
NCEER-97-00I3 "Seismic Design of Bridge Columns Based on Control and Repairability of Damage," by C-T. Cheng and
J.B. Mander, 12/8/97.
NCEER-97-00l4 "Seismic Resistance of Bridge Piers Based on Damage Avoidance Design," by J.B. Mander and C-T.
Cheng, 12110/97.
NCEER-97-00l5 "Seismic Response ofNominally Symmetric Systems with Strength Uncertainty," by S. Balopoulou and M
Grigoriu, 12/23/97, (PB98-l53422, All, MF-A03).

NCEER-97-0016 "Evaluation of Seismic Retrofit Methods for Reinforced Concrete Bridge Colwnns," by T.J. Wipf, F.W.
Klaiber and F.M. Russo, 12/28/97.
NCEER-97-0017 "Seismic Fragility of Existing Conventional Reinforced Concrete Highway Bridges," by C.L. Mullen and
AS. Cakmak, 12/30/97, (PB98-153406, A08, MF-A02).
NCEER-97-0018 "Loss Asssessment ofMemphis Buildings," edited by D.P. Abrams and M. Shinozuka, 12/31/97.
NCEER-97-0019 "Seismic Evaluation ofFrames with fufill Walls Using Quasi-static Experiments," by K.M. Mosalam, R.N.
White and P. Gergely, 12/31/97, (PB98-153455, A07, MF-A02).
NCEER-97-0020 "Seismic Evaluation of Frames with fufill Walls Using Pseudo-d}namic Experiments," by K.M. Mosalam,
R.N. White and P. Gergely, 12/31/97.
NCEER-97-0021 "Computational Strategies for Frames with fufill Walls: Discrete and Smeared Crack Analyses and Seismic
Fragility," by K.M. Mosalam, R.N. White and P. Gergely, 12/31/97, (PB98-153414, AlO, MF-A02).
NCEER-97-0022 "Proceedings of the NCEER Workshop on Evaluation of Liquefaction Resistance of Soils," edited by T.L.
Youd and I.M. Idriss, 12/31/97.
MCEER-98-0001 "Extraction of Nonlinear Hysteretic Properties of Seismically Isolated Bridges from Quick-Release Field
Tests," by Q. Chen, B.M. Douglas, E.M. Maragakis and I.G. Buckle, 5/26/98.
MCEER-98-0002 "Methodologies for Evaluating the bnportance of Highway Bridges," by A Thomas, S. Eshenaur and l
Kulicki, 5/29/98.
MCEER-98-0003 "Capacity Design ofBridge Piers and the Analysis of Overstrength," by J.B. Mander, A Dutta and P. Goel,
6/1/98.
MCEER-98-0004 "Evaluation of Bridge Damage Data from the Lorna Prieta and Northridge, California Earthquakes," by N.
Basoz and A Kiremidjian, 6/2/98.
MCEER-98-0005 "Screening Guide for Rapid Assessment of Liquefaction Hazard at Highway Bridge Sites,"by T. L. Youd,
6/16/98.
MCEER-98-0006 "Structural Steel and SteeVConcrete Interface Details for Bridges," by P. Ritchie, N. Kauhl and l Kulicki,
7/13/98.
MCEER-98-0007 "Capacity Design and Fatigue Analysis of Confmed Concrete Columns," by A Dutta and lB. Mander,
7/14/98.
MCEER-98-0008 "Proceedings ofthe Workshop on Performance Criteria for Telecommunication Services Under Earthquake
Conditions," edited by Al Schiff, 7/15/98.
MCEER-98-0009 "Fatigue Analysis ofUnconfmed Concrete Columns," by lB. Mander, A Dutta and lH. Kim, 9/12/98.
MCEER-98-001O "Centrifuge Modeling of Cyclic Lateral Response of Pile-Cap Systems and Seat-Type Abutments in Dry
Sands," by AD. Gadre and R. Dobry, 10/2/98.
MCEER-98-0011 "IDARC-BRIDGE: A Computational Platform for Seismic Damage Assessment of Bridge Structures," by
AM. Reinhorn, V. Simeonov, G. Mylonakis and Y. Reichman, 10/2/98.
MCEER-98-0012 "Experimental Investigation of the Dynamic Response of Two Bridges Before and After Retrofitting with
Elastomeric Bearings," by D.A. Wendichansky, S.S. Chen and lB. Mander, 10/2/98.
Fonnerlythe National Center for Earthquake Engineering Research 111

MCEER-98-0013 "Design Procedures for Hinge Restrainers and Hinge Sear Width for Multiple-Frame Bridges," by R. Des
Roches and G.L. Fenves, 1113/98.
MCEER-98-0014 "Response Modification Factors for Seismically Isolated Bridges," by M.C. Constantinou and J.K.
Quarshie,11/3/98.
MCEER-98-0015 ''Proceedings of the U.S.-Italy Workshop on Seismic Protective Systems for Bridges," edited by 1M.
Friedland and M.C. Constantinou, 11/3/98.
MCEER-98-0016 "Appropriate Seismic Reliability for Critical Equipment Systems: Recommendations Based on Regional
Analysis ofFinancial and Life Loss," by K. Porter, C. Scawthorn, C. Taylor and N. Blais, 11110/98.
MCEER-98-0017 "Proceedings of the U.S. Japan Joint Seminar on Civil hUrastructure Systems Research," edited by M.
Shinozuka and A. Rose, 11112/98.
MCEER-98-0018 "Modeling of Pile Footings and Drilled Shafts for Seismic Design," by I. PoLam, M. Kapuskar and D.
Chaudhuri,12/21198.
MCEER-99-000l "Seismic Evaluation ofa Masonry Infilled Reinforced Concrete Frame by Pseudodynamic Testing," by S.G.
Buonopane and R.N. White, 2116/99.
MCEER-99-0002 "Response History Analysis of Structures with Seismic Isolation and Energy Dissipation Systems:
Verification Examples for Program SAP2000," by J. S~heller and M.C. Constantinou, 2/22/99.

Response History Analysis of Structures SAP2000.pdf

More Related Content

Similar to Response History Analysis of Structures SAP2000.pdf (20)

Recently uploaded (20)

Response History Analysis of Structures SAP2000.pdf