Satellite Communication for BTech ECE students

EC8094: Satellite Communication Department of ECE
2020 - 2021 1 Jeppiaar Institute of Technology
EC8094 - SATELLITE COMMUNICATION
L T P C
3 0 0 3
OBJECTIVES:
The student should be made to:
 Understand the basics of satellite orbits
 Understand the satellite segment and earth segment
 Analyze the various methods of satellite access
 Understand the applications of satellites
 Understand the basics of satellite Networks
UNIT I SATELLITE ORBITS 9
Kepler‟s Laws, Newton‟s Law, Orbital Parameters, Orbital Perturbations, Station Keeping, Geo
Stationary and Non Geo-Stationary Orbits – Look Angle Determination - Limits of Visibility –
Eclipse - Sub Satellite Point – Sun Transit Outage - Launching Procedures - Launch Vehicles
and Propulsion.
UNIT II SPACE SEGMENT 9
Spacecraft Technology - Structure, Primary Power, Attitude and Orbit Control, Thermal Control
and Propulsion, Communication Payload and Supporting Subsystems, Telemetry, Tracking and
Command – Transponders - The Antenna Subsystem.
UNIT III SATELLITE LINK DESIGN 9
Basic Link Analysis, Interference Analysis, Rain Induced Attenuation and Interference,
Ionospheric Characteristics, Link Design with and without Frequency Reuse.
UNIT IV SATELLITE ACCESS AND CODING METHODS 9
Modulation and Multiplexing: Voice, Data, Video, and Analog – Digital Transmission System,
Digital Video Broadcast, Multiple Access: FDMA, TDMA, CDMA, DAMA Assignment
Methods, Compression – Encryption, Coding Schemes.
UNIT V SATELLITE APPLICATIONS 9
INTELSAT Series, INSAT, VSAT, Mobile Satellite Services: GSM, GPS, INMARSAT, LEO,
MEO, Satellite Navigational System. GPS Position Location Principles, Differential GPS, Direct
Broadcast satellites (DBS/DTH).
TOTAL:45 PERIODS
OUTCOMES:
At the end of the course, the student would be able to:
 Analyze the satellite orbits
 Analyze the earth segment and space segment
 Analyze the satellite Link design
 Design various satellite applications

TEXT BOOKS:
1. Dennis Roddy, “Satellite Communication”, 4th Edition, Mc Graw Hill International,
2006.
2. Timothy,Pratt,Charles,W.Bostain,JeremyE.Allnutt,"SatelliteCommunication”,2ndEdition,
Wiley Publications,2002
REFERENCES:
1. Wilbur L.Pritchard, Hendri G. Suyderhoud, Robert A. Nelson, “Satellite Communication
Systems Engineering”, Prentice Hall/Pearson, 2007.
2. N.Agarwal, “Design of Geosynchronous Space Craft”, Prentice Hall, 1986.
3. Bruce R. Elbert, “The Satellite Communication Applications”, Hand Book, Artech House
Bostan London, 1997.
4. Tri T. Ha, “Digital Satellite Communication”, II nd edition, 1990.
5. Emanuel Fthenakis, “Manual of Satellite Communications”, Mc Graw Hill Book
Co.,1984.
6. Robert G. Winch, “Telecommunication Trans Mission Systems”, Mc Graw-Hill Book
Co., 1983.
7. Brian Ackroyd, “World Satellite Communication and earth station Design”, BSP
professional Books, 1990.
8. G.B.Bleazard, “Introducing Satellite communications“, NCC Publication, 1985.
9. M.Richharia, “Satellite Communication Systems-Design Principles”, Macmillan 2003.

UNIT I
SATELLITE ORBITS
Kepler‟s Laws, Newton‟s Law, Orbital Parameters, Orbital Perturbations, Station Keeping, Geo
Stationary and Non Geo-Stationary Orbits – Look Angle Determination - Limits of Visibility –
Eclipse - Sub Satellite Point – Sun Transit Outage - Launching Procedures - Launch Vehicles
and Propulsion.

Satellite
The word satellite originated from the Latin word “Satellit”- meaning an attendant, one who is
constantly covering around & attending to a “master” or big man
 Earth Stations – antenna systems on
earth
• Uplink – transmission from an earth
station to a satellite
• Downlink – transmission from a
satellite to an earth station
• Transponder – electronics in the
satellite that convert uplink signals to downlink
signals
First satellite launched into space: Sputnik (1957).

Motion of Space Objects
1473 -1543 Copernicus - Heliocentric (sun in the center) Orbit
1546 – 1601 Tycho Brahe
Before telescope followed the planets (acquired quality
data)
1571 – 1630 Johannes Kepler
Discovered orbital path to be elliptical around focus point
Keplers 3 laws of planetary motion
1642 – 1727 Sir Isaac Newton
Physical Principals – Universal law of Gravitation
NEWTON’S LAWS
Newton’s First law: Law of Inertia
Everybody continues in a state of uniform motion unless it is compelled to change that state by a
force imposed upon it.
Newton’s Second law: Law of Momentum
Change in momentum is proportional to and in the direction of the force applied. Momentum
equals mass x velocity. Change in momentum gives: F=ma.
Newton’s Third law: Action – Reaction
For every action, there is an equal and opposite reaction. Hints at conservation of momentum

Origin of orbital mechanics
Kepler’s laws:
Kepler’s laws apply quite generally to any two bodies in space which interact through
gravitation. The more massive of the two bodies is referred to as the primary, the other,
the secondary or satellite.
Keplers 3 (empirical) laws of Planetary Motion
1. Kepler’s first law states that, the path followed by a satellite around a primary is elliptical
with the center of masses at one of the foci.
(OR)
“The orbital path of a planet takes the shape of an ellipse, with the Sun located at one of its
focal points.”
2. Kepler’s second law states that, for equal time
intervals, a satellite will sweep equal areas in its
orbital plane.
(OR)
The line from the sun to a planet sweeps out equal
areas in equal time intervals.
PHYSICAL LAWS
Kepler‟s 1st Law: Law ofEllipses
The orbits ofthe planets are ellipses with
the sun at one focus
PHYSICAL LAWS
Kepler‟s 1st Law: Law of Ellipses
The orbits of the planets are ellipses with
the sun at one focus
PHYSICAL LAWS
Kepler‟s 2nd Law: Law of Equal Areas
The line joining the planet to the center of the sun
sweeps out equal areas in equal times
T6
T5
T4 T3
T2
T1
A2
A3
A4
A5
A6
A1
PHYSICAL LAWS
Kepler‟s 2nd Law: Law of Equal Areas
The line joining the planet to the center of the sun
sweeps out equal areas in equal times
T6
T5
T4 T3
T2
T1
A2
A3
A4
A5
A6
A1

3. Kepler’s third law states that, the square of the periodic time of orbit is proportional to the
cube of the mean distance between the two bodies.
Where,
T is the orbital period
a is the semi major axis of the orbital ellipse
µ is the Kepler‟s constant = 3.986005*1014
(OR)
The ratio of the square of the planet‟s orbital period and the
cube of the mean distance from the Sun is constant
(D1/D2)3
= (P1/P2)2
Example:
Calculate the radius of a circular orbit for which the period is 1 day.
Solution There are 86,400 seconds in 1 day, and therefore the mean motion is
Mean motion of the satellite
n =7.272 * 10-5
rad/s
From Kepler’s third law:
( )
*( )
+ = 42,241 km
Since the orbit is circular the semi major axis is also the radius.
PHYSICAL LAWS
Kepler‟s 3rd Law: Law of Harmonics
The squares of the periods of
two planets‟ orbits are
proportional to each other as
the cubes of their semi-
major axes:
T1
2/T2
2 = a1
3/a2
3
In English:
Orbits with the same semi-
major axis will have the
same period
PHYSICAL LAWS
Kepler‟s 3rd Law: Law of Harmonics
The squares of the periods of
two planets‟ orbits are
proportional to each other as
the cubes of their semi-
major axes:
T12/T22 = a13/a23
In English:
Orbits with the same semi-
major axis will have the
same period

Frequency Allocation and Regulatory Aspects
 Frequency band for satellite services are shared with terrestrial services.
 Satellite signal strength is constrained to avoid interference by it to others.
 Thus a large antenna and sensitive receiver are needed at the earth station.
 Frequency sharing techniques are important study area.
 Many satellites have to share a limited frequency band (and limited orbital arc) thus
coordination in frequency and orbital location is important.
 Frequency allocations are done by international agreements.
Frequency Allocation for Satellite Communication
Band Frequency Range Total
Bandwidth
General Applications
L 1 TO 2 GHz 1 GHz Mobile Satellite Services (MSS)
S 2 TO 4 GHz 2 GHz MSS, NASA, Deep Space Research
C 4 TO 8 GHz 4 GHz Fixed Satellite Services (FSS)
X 8 TO 12.5 GHz 4.5 GHz FSS Military, Terrestrial Explosion
and Metrological Satellites
Ku 12.5 TO 18 GHz 5.5 GHz FSS, Broadcast Satellite Services (BSS)
K 18 TO 26.5 GHz 8.5 GHz BSS, FSS
Ka 26.5 TO 40 GHz 13.5 GHz FSS
Regulatory Aspects:
Domestic: Example:
Federal Communication Commission (FCC)
National Telecommunication and Information Administration (NITA)
In Pakistan, PTA (Pakistan Telecommunication Authority)
International: Example: International Telecommunication Union (ITU)
 Formed in 1932 from the International Telegraph Union
 Consists of over 150 members nations
 World Administrative radio Conference (WARC)
 International Radio consultative committee (CCIR) consists of 13 group.
 World is divided into three regions:
Region 1 – Europe, Africa, Soviet Union on Mongolia
Region 2 – North and South America, Greenland
Region 3 – Asia, Australia and South West Pacific
Frequency Bands Available for Satellite Communications
Band Uplink (GHz) Downlink (GHz)
C 6 4
Ku 14 12
Ka 30 20
X 8.2 7.5
S 40 20
Q 44 21
L 1.525 to 1.559 1.626 to 1.660

APPLICATIONS
1. Global Telecommunications : Land, Sea, Air
2. Broadcasting : Sound, TV, Multimedia, Cable TV, DTH, DTU, DBS, DVB
3. Navigation : Global Positioning System (GPS)
4. Remote Sensing – Earth Observation
5. Weather
6. Emergency Communication Services – Disasters
7. Mobile Communication Services
8. Corporate Communications – Virtual Private Network (VPN), VSAT Technology
9. Military Communications etc.,
Different services of satellite systems
 Fixed satellite services
 Broadcasting satellite services
 Mobile satellite services
 Navigational satellite services
 Meteorological satellite services.
Satellite Communication Configurations

Satellite Orbits
An orbit is the path that a satellite follows as it revolves
around Earth
Satellites orbits vary depending on:
1) Altitude 2) Inclination 3) Orbital Period
Three classes of Satellite orbits:
1) Low Earth Orbit (LEO)
Up to 2,000km altitude
Remote sensing satellites, altimeter satellites
2) Medium Earth Orbit (MEO)
Altitudes between 5,000km – 20,000km
GPS satellites (12 hr periods – twice a day)
3) Geostationary Earth Orbit (GEO)
24hrs period appears fixed
Altitudes of 36,000km
Communication satellites

Motion of Space Objects
Orbital Mechanics
• Gravity depends on the mass of the earth,
the mass of the satellite, and the distance
between the center of the earth and the satellite
• For a satellite traveling in a circle, the
speed of the satellite and the radius of the circle
determine the force (of gravity) needed to
maintain the orbit
• The radius of the orbit is also the distance from the center of the earth.
• For each orbit the amount of gravity available is therefore fixed
• That in turn means that the speed at which the satellite travels is determined by the orbit
• From what we have deduced so far, there has to be an equation that relates the orbit and
the speed of the satellite:
T is the time for one full revolution around the orbit, in seconds
r is the radius of the orbit in meters, including the radius of the earth (6.38x106
m).
Common Example
• “Height” of the orbit = 22,300 mile
• That is 36,000km = 3.6x107
m
• The radius of the orbit is 3.6x107
m + 6.38x106
m = 4.2x107
m
14
3
10
4
2


r
T 

LEO Satellite Characteristics
• Circular/slightly elliptical orbit under 2000 km
• Orbit period ranges from 1.5 to 2 hours
• Diameter of coverage is about 8000 km
• Round-trip signal propagation delay less than 20 ms
• Maximum satellite visible time up to 20 min
• System must cope with large Doppler shifts
• Atmospheric drag results in orbital deterioration
MEO Satellite Characteristics
• Circular orbit at an altitude in the range of 5000 to 12,000 km
• Orbit period of 6 hours
• Diameter of coverage is 10,000 to 15,000 km
• Round trip signal propagation delay less than 50 ms
• Maximum satellite visible time is a few hours
GEO Satellite Characteristics
• Advantages of the GEO orbit
• No problem with frequency changes
• Tracking of the satellite is simplified
• High coverage area
• Disadvantages of the GEO orbit
• Weak signal after traveling over 35,000 km
• Polar regions are poorly served
• Signal sending delay is substantial
The Geosynchronous Orbit
• The answer is T = 86,000 sec (rounded)
• 86,000 sec = 1,433 min = 24hours (rounded)
• The satellite needs 1 day to complete an orbit
• Since the earth turns once per day, the satellite moves with the surface of the earth.
Comparison Chart
Features GEO MEO LEO
Height (Km’s) 36000 6000 - 12000 200 - 3000
Time per orbit (Hrs) 24 5 – 12 1.5
Speed (Km’s / hr) 11000 19000 27000
Time Delay (ms) 250 80 10
Time in Site of Gateway Always 2 – 4 hrs < 15 min
Satellite for Global Coverage 3 10 – 12 50 - 70
Satellite orbit altitudes

Definitions & orbital parameters
Some of the important terms required in order to understand the orbital elements are given
below:
1. Sub Satellite Path: This is the path traced out on the earth‟s surface directly below the
satellite.
2. Apogee: The point farthest from the earth. (Apogee height -ha)
3. Perigee: The point of closest approach to earth. (Perigee height -ha)
4. Line of apsides: The line joining the perigee and apogee through the center of the earth.
5. Ascending node: The point where the orbit crosses the equatorial plane going from south to
north.
6. Descending node: The point where the orbit crosses the equatorial plane going from north to
south.
7. Line of nodes: The line joining the ascending and descending nodes through the center of
the earth.
8. Inclination: The angle between orbital plane and the earth‟s equatorial plane. It is measured
at the ascending node from equator to the orbit, going from east to north.
9. Declination: The angle of tilt is often referred to as the declination which must not be
confused with the magnetic declination used in correcting compass readings.
10. Prograde orbit: An orbit in which the satellite moves in the same direction as the earth‟s
rotation (West to East). The prograde orbit is also known as the direct orbit. The inclination
of a prograde orbit always lies between 0 and 90 degrees. Most satellites are launched in a
prograde orbit because the earth‟s rotational velocity provides part of the orbital velocity
with a consequent saving in launch energy.
11. Retrograde orbit: An orbit in which the satellite moves in a direction of satellite motion.
12. Argument of perigee (w): The angle from ascending node to perigee, measured in the
orbital plane at the earth‟s center, in the direction of satellite motion.
13. Right ascension of the ascending node (Ὠ) is the angle measured eastward in the equatorial
plane from the line of Aries/ First point of Aries (ɤ) to the ascending node.
14. Mean Anomaly (δm) is an average value of the angular position of the satellite with
reference to the perigee.
15. True Anomaly is the angle from perigee to the satellite position measured at the earth‟s
centre.

Orbital Elements
Orbital elements are the six quantities required to determine the absolute coordinates of a
satellite at time t. The orbital elements are:
1. The semi major axis (a): It represents half the length of the major axis of the elliptical orbit
described by the satellite.
2. The eccentricity (e): Eccentricity of the ellipse.
3. The mean anomaly (M): Anomaly is the term for angle. Mean anomaly is the angle which
describes the position of the satellite in its orbit relative to the perigee. At perigee, mean
anomaly is zero. It increases to 180 degrees at apogee and back to perigee at 360 degrees.
4. The argument of perigee: It is the angle between the perigee points on the semi-major axis
to the semi lotus rectum which joins the satellite to the centre of the earth.
5. The inclination: The angle that the orbital plane makes with the equatorial plane is called
the inclination.
6. The right ascension of the ascending node: It is the angle between the vernal equinox line
and the line of nodes measured in the equatorial plane.
For an elliptical orbit, 0 < e < 1. When e = 0, the orbit becomes circular.

Orbital Location:
The location of a geostationary satellite is referred to as its orbital location. International
satellites are normally measured in terms of longitudinal degrees East (° E) from the Prime
Meridian of 0°
Footprint
The geographic area of the Earth's surface over which a satellite can transmit to, or receive from,
is called the satellite's "footprint."
Height of Apogee & Perigee:
The apogee & Perigee heights are often required. The length of the radius vectors at apogee and
perigee can be obtained from the geometry of the eclipse.
ra = a (1+e)
rp = a (1-e)
Orbital perturbations
The orbit discussed so far is referred to as Keplerian orbit, is elliptical for the special case of an
artificial satellite orbiting the earth. However, the Keplerian orbit is ideal in the sense that it
assumes that the earth is a uniform spherical mass, and the only force acting is the centrifugal
force, resulting from satellite motion balancing the gravitational pull of the earth.
In practice, other forces which can be significant are the gravitational forces of the sun and the
moon, atmospheric drag and earth‟s oblate
The gravitational pull of sun and moon has negligible effect on low orbiting satellites, but they
do affect satellites in the geo stationary orbit.
Atmospheric drag, on the other hand has negligible effect on geostationary satellites, but does
affect low orbiting satellites below 1000 k.m.
Effect of a Non Spherical Earth
For a spherical earth of uniform mass, kepler‟s third law gives the nominal no as,
√
The „o‟ subscript is included to show for perfectly spherical earth of uniform mass.
However, earth is not perfectly spherical (Oblate Spheroid) taken into account and mean motion
n is modified as,
*
( )
( )
+
k1 is constant – 66,063.1704 km2
. The earth‟s oblateness has negligible effect on „a‟ if a is
known. The mean motion is readily calculated. The orbital period taking into account the earth‟s
oblateness is anamalistic period (Perigee to Perigee)

The anamalistic period is,
n – is radians/sec. If n is known quantity we can solve for
√ *
( )
( )
+
The oblateness of earth also produces two rotations of the orbital plane is known as regression
of nodes, is where the nodes appear to slide along the equator.
In effect, the line of nodes, which is in the equatorial plane, rotates about the center of the earth.
Thus Ὠ, the right ascension of the ascending node shifts its position.
If the orbit is prograde, the nodes slide westward, and if retrograde, they slide eastward. As seen
from the ascending node, a satellite in prograde orbit moves eastward, and in a retrograde orbit,
westward. The nodes therefore move in a direction opposite to the direction of satellite
motion, hence the term regression of the nodes.
The second effect is rotation of apsides in the orbital plane, described below. Both effects
depend on the mean motion n, the semi major axis a, and the eccentricity e. These factors can be
grouped into one factor K given by
( )
K will have the same units as n. Thus, with n in rad/day, K will be in rad/day, and with n in
degrees/day, K will be in degrees/day.
An approximate expression for the rate of change of _ with respect to time is
Where i is the inclination. The rate of regression of the nodes will have the same units as n.
When the rate of change given by above Equation is negative, the regression is westward, and
when the rate is positive, the regression is eastward. It will be seen, therefore that for eastward
regression, i must be greater than 90o
, or the orbit must be retrograde. It is possible to choose
values of a, e, and i such that the rate of rotation is 0.9856°/day eastward.
The other major effect produced by the equatorial bulge is a rotation of the line of apsides. This
line rotates in the orbital plane, resulting in the argument of perigee changing with time. The rate
of change is given by
( )
Again, the units for the rate of rotation of the line of apsides will be the same as those for n
(incorporated in K). When the inclination i is equal to 63.435°, the term within the parentheses is

equal to zero, and hence no rotation takes place. Use is made of this fact in the orbit chosen for
the Russian Molniya satellites
Denoting the epoch time by t0, the right ascension of the ascending node by Ω0, and the argument
of perigee by w0 at epoch gives the new values for Ω and w at time t as
( )
( )
Keep in mind that the orbit is not a physical entity, and it is the forces resulting from an oblate
earth, which act on the satellite to produce the changes in the orbital parameters. Thus, rather
than follow a closed elliptical path in a fixed plane, the satellite drifts as a result of the regression
of the nodes, and the latitude of the point of closest approach (the perigee) changes as a result of
the rotation of the line of apsides.
With this in mind, it is permissible to visualize the satellite as following a closed elliptical orbit
but with the orbit itself moving relative to the earth as a result of the changes in Ω and w. Thus,
as stated earlier, the period PA is the time required to go around the orbital path from perigee to
perigee, even though the perigee has moved relative to the earth.
Equatorial Ellipticity: In addition to the equatorial bulge, the earth is not perfectly circular in the
equatorial plane; it has a small eccentricity of the order of 10−5
. This is referred to as the
equatorial ellipticity. The effect of the equatorial In addition to the equatorial bulge, the earth is
not perfectly circular ellipticity is to set up a gravity gradient, which has a pronounced effect on
satellites in geostationary orbit. Very briefly, a satellite in geostationary orbit ideally should
remain fixed relative to the earth. The gravity gradient resulting from the equatorial Ellipticity
causes the satellites in geostationary orbit to drift to one of two stable points, which coincide
with the minor axis of the equatorial ellipse. These two points are separated by 180°on the
equator and are at approximately 75° E longitude and 105°W longitude. Satellites in service are
prevented from drifting to these points through station-keeping maneuvers. Because old, out-of-
service satellites eventually do drift to these points, they are referred to as “satellite
graveyards.” It may be noted that the effect of equatorial ellipticity is negligible on most other
satellite orbits.
Atmospheric drag: For near-earth satellites, below about 1000 km, the effects of atmospheric
drag are significant. Because the drag is greatest at the perigee, the drag acts to reduce the
velocity at this point, with the result that the satellite does not reach the same apogee height on
successive revolutions. The result is that the semi major axis and the eccentricity are both
reduced. Drag does not noticeably change the other orbital parameters, including perigee height.
An approximate expression for the change of major axis is
[
( )
]
Where the “0” subscripts denote values at the reference time t0, and n0 is the first derivative of
the mean motion. The mean anomaly is also changed, an approximate value for the change
being:
( )

Earth Eclipse of Satellite
If the earth‟s equatorial plane coincided with the plane of the earth‟s orbit around the sun
(the ecliptic plane), geostationary satellites would be eclipsed by the earth once each day. As it
is, the equatorial plane is tilted at an angle of 23.4° to the ecliptic plane, and this keeps the
satellite in full view of the sun for most days of the year, as illustrated by position A in Figure.
Around the spring and autumnal equinoxes, when the sun is crossing the equator, the satellite
does pass into the earth‟s shadow at certain periods, these being periods of eclipse as illustrated
in Figure. The spring equinox is the first day of spring, and the autumnal equinox is the first day
of autumn.
Eclipses begin 23 days before equinox and end 23 days after equinox. The eclipse lasts about 10
min at the beginning and end of the eclipse period and increases to a maximum duration of about
72 min at full eclipse (Spilker, 1977).
During an eclipse, the solar cells do not function, and operating power must be supplied from
batteries. Where the satellite longitude is east of the earth station, the satellite enters eclipse
during daylight (and early evening) hours for the earth station, as illustrated in Fig. This can be
undesirable if the satellite has to operate on reduced battery power.
Where the satellite longitude is west of the earth station, eclipse does not occur until the earth
station is in darkness, (or early morning) when usage is likely to be low. Thus satellite longitudes
which are west, rather than east, of the earth station are more desirable.
Sun transit outage
During the equinox periods, the orbit of the satellite will also pass directly in front of the sun on
the sunlit side of the earth. The sun is a hot microwave source with an equivalent temperature of
about 6000 to 10000 K, depending on the time within the 11- year sunspot cycle, at the
frequencies used by the communication satellites (4 to 50 GHz). The earth station will therefore
receive not only the signal from the satellite but also the noise temperature transmitted by the
sun. The added noise temperature will cause the fade margin of the receiver to be exceeded and
an outage will occur. This is termed as Sun transit outage.

Sun transits occur when the sun crosses the earth's equatorial plane during the spring and fall
equinoxes (late February or early March; September or October). At these times, the sun aligns
directly behind the satellites for a few minutes each day. When the sun moves directly behind the
satellite to your receive antenna, the satellite signal can be overwhelmed by the enormous
amount of thermally generated radio frequency (RF) noise radiated by the sun. This can cause
reception interference for a few minutes every day during this occurrence.
The time of occurrence depends both on the geographic location of the earth station and the
location of the satellite. The sun may degrade the signal for several minutes depending on the
antenna size and available link margin, although it is not unusual for the effect to go unnoticed.
The number of outages, outage duration and the time of outage depend on the radio emission
activity of the sun, the movement of the earth with respect to the sun, the pointing and location of
receive antenna, and characteristics of the communication system. Those characteristics, in turn,
include the operating receive radio frequency, the receive antenna gain pattern, the clear sky
operating carrier-to-noise ratio (C/N), the clear sky equivalent system noise temperature and the
minimum acceptable C/N.
When the sun transits occur, the antenna noise temperature varies depending on the antenna size,
the elevation angle, location and environment.
Computer generated predictions revealed that sun transits peak times of all days associated with
an equinox for a given receive earth station do not differ from each other by more than a minute,
and they do not vary much with respect to the year considered. The variations are less than one
minute for at least the next decade. Thus for practical purposes, they can be considered the same
and invariant with respect to the year they are considered.

Antenna Look Angles
The look angles for the ground station antenna are the azimuth and elevation angles required at
the antenna so that it points directly at the satellite. The look angles were determined in the
general case of an elliptical orbit, and there the angles had to change in order to track the
satellite. With the geostationary orbit, the situation is much simpler because the satellite is
stationary with respect to the earth. Although in general no tracking should be necessary, with
the large earth stations used for commercial communications, the antenna beamwidth is very
narrow, and a tracking mechanism is required
To compensate for the movement of the satellite about the nominal geostationary position. With
the types of antennas used for home reception, the antenna beamwidth is quite broad, and no
tracking is necessary. This allows the antenna to be fixed in position, as evidenced by the small
antennas used for reception of satellite TV that can be seen fixed to the sides of homes.
The three pieces of information that are needed to determine the look angles for the
geostationary orbit are
1. The earth-station latitude, denoted here by λE
2. The earth-station longitude, denoted here by ФE
3. The longitude of the subsatellite point, denoted here by ФSS (often this is just referred to as
the satellite longitude)
Latitudes north will be taken as positive angles, and latitudes south, as negative angles.
Longitudes east of the Greenwich meridian will be taken as positive angles, and longitudes west,
as negative angles. For example, if latitude of 40° S is specified, this will be taken as - 40°, and if
a longitude of 35° W is specified, this will be taken as -35°.
When calculating the look angles for low-earth-orbit (LEO) satellites, it was necessary to take
into account the variation in earth‟s radius. With the geostationary orbit, this variation has
negligible effect on the look angles, and the average radius of the earth will be used. Denoting
this by R: R = 6371 km
The geometry involving these quantities is shown in above Figure. Here, ES denotes the position
of the earth station, SS the sub satellite point, S the satellite, and d is the range from the earth
station to the satellite. The angle is an angle to be determined.

There are two types of triangles involved in the geometry of above Figure, the spherical triangle
and the plane triangle shown in heavy outline in below Figures.
Considering first the spherical triangle, the sides are all arcs of great circles, and these sides are
defined by the angles subtended by them at the center of the earth. Side a is the angle between
the radius to the North Pole and the radius to the subsatellite point, and it is seen that a= 90°. A
spherical triangle in which one side is 90° is called a quadrantal triangle. Angle b is the angle
between the radius to the earth station and the radius to the subsatellite point. Angle c is the
angle between the radius to the earth station and the radius to the north pole. From above Figure
it is seen that c= 90°- λE.
There are six angles in all defining the spherical triangle. The three angles A, B, and C are the
angles between the planes. Angle A is the angle between the plane containing c and the plane
containing b. Angle B is the angle between the plane containing c and the plane containing a.
From above figure B= ФE - ФSS. It will be shown shortly that the maximum value of B is 81.3°.
Angle C is the angle between the plane containing b and the plane containing a. To summarize to
this point, the information known about the spherical triangle is
a = 90°, c = 90°- λE and B= ФE - ФSS
Note that when the earth station is west of the subsatellite point, B is negative, and when east,
B is positive. When the earth-station latitude is north, c is less than 90°, and when south, c is
greater than 90°. Special rules, known as Napier’s rules, are used to solve the spherical triangle,
and these have been modified here to take into account the signed angles B and λE. Only the
result will be stated here. Napier‟s rules gives angle b as
( )
and angle A as
(
| |
)
Two values will satisfy the above Equation, A and 180°- A, and these must be determined by
inspection. These are shown in below figures. Angle A is acute (less than 90°), and the azimuth
angle is Az = A.
In second Figure, angle A is acute, and the azimuth is, by inspection, Az =360°- A. In Third
Figure, angle Ac is obtuse and is given by Ac=180° - A, where A is the acute value obtained from
angle A Equation. Again, by inspection, Az = Ac - 180°- A.

In Figure Four, angle Ad is obtuse and is given by 180°- A, where A is the acute value obtained
from angle A Equation. By inspection, Az = 360° - Ad = 180° + A.
In all cases, A is the acute angle returned by angle A Equation. These conditions are summarized
in below Table.
Angle λE B Az, Degrees
a < 0 < 0 A
b < 0 > 0 360° - A
c > 0 < 0 180° - A
d > 0 > 0 180° + A
Applying the cosine rule for plane triangles to the triangle Figure allows the range d to be found
to a close approximation:
√
Applying the sine rule for plane triangles to the triangle Figure allows the angle of elevation to
be found:
( )

Example Problem:
A geostationary satellite is located at 90°W. Calculate the azimuth angle for an earth
station antenna at latitude 35°N and longitude 100°W. And also find the range and antenna
elevation angle.
Solution the given quantities are
ФSS = - 90° (West) , λE = 35° (North), ФE = - 100° (West)
B= ФE - ФSS = -100 + 90 = -10°
angle b as
( ) = 36.23°
and angle A as
(
| |
) = 17.1°
azimuth is, by inspection, λE > 0 and B < 0, therefore
Az =180°- A = 162.9 °
range d
√
R- Earth radius = 6371 or 6378
d = 37215 km
Angle of elevation
( ) = 48°
The Polar Mount Antenna
Where the home antenna has to be steerable, expense usually precludes the use of separate
azimuth and elevation actuators. Instead, a single actuator is used which moves the antenna in a
circular arc. This is known as a polar mount antenna.
Angle of tilt: and b=
( )

Example:
Determine the angle of tilt required for a polar mount used with an earth station at latitude
49° north. Assume a spherical earth of mean radius 6371 km, and ignore earth-station
altitude
range d
√ = 38287 km
Angle of elevation
( )
Angle of tilt:
= 7
Limits of Visibility
There will be east and west limits on the geostationary arc visible from any given earth station.
The limits will be set by the geographic coordinates of the earth station and the antenna
elevation. The lowest elevation in theory is zero, when the antenna is pointing along the
horizontal. A quick estimate of the longitudinal limits can be made by considering an earth
station at the equator, with the antenna pointing either west or east along the horizontal, as shown
in Figure. The limiting angle is given by
Thus, for this situation, an earth station could see satellites over a geostationary arc bounded by
81.3° about the earth-station longitude.

In practice, to avoid reception of excessive noise from the earth, some finite minimum value of
elevation is used, which will be denoted here by Elmin. A typical value is 5°. The limits of
visibility will also depend on the earth-station latitude. As in Figure, let S represent the angle
subtended at the satellite when the angle min = 90° - Elmin. Applying the sine rule gives
( )
A sufficiently accurate estimate is obtained by assuming a spherical earth of mean radius
6371 km as was done previously. Once angle S is known, angle b is found from
( )
Example:
Determine the limits of visibility for an earth station situated at mean sea level, at latitude
48.42° north, and longitude 89.26 degrees west. Assume a minimum angle of elevation of 5°.
R- Earth radius = 6371 or 6378
min = 90° - Elmin = 95
( )= 8.66
( )= 69.15
The satellite limit east of the earth station is at
- 20
and west of the earth station at
- 158

Sub Satellite Point
The point on the earth vertically under the satellite is referred to as the subsatellite point.
The latitude and longitude of the subsatellite point and the height of the satellite above the
subsatellite point can be determined from knowledge of the radius vector r. The above Figure
shows the meridian plane which cuts the subsatellite point. The height of the terrain above the
reference ellipsoid at the subsatellite point is denoted by HSS, and the height of the satellite
above this, by hSS. Thus the total height of the satellite above the reference ellipsoid is
Sidereal Time:
1. Sidereal time is the time measured relative to the fixed stars.
2. Sidereal day is defined as one complete rotation of the earth relative to the fixed star.
1 mean solar day = 1.0027379093 mean sidereal days
= 24 h
3m
56s
.55536 sidereal time
= 86,636.55536 mean sidereal seconds.
1 mean sidereal day = 0.9972695664 mean solar days
= 23h
56 m
04s
.09054 mean solar time
= 86,164.09054 mean solar seconds.

Geostationary Orbit
1. A satellite in a geostationary orbit appears to be stationary with respect to the earth.
2. Three conditions are required for an orbit to be stationary.
 The satellite must travel eastward at the same rotational speed as the earth.
 The orbit must be circular.
 The inclination of the orbit must be 0.
3. The radius of the geostationary orbit=42164km.
Satellites in geosynchronous orbit
Uses of Geostationary Orbits
Geostationary orbits are primarily used for two functions:
• Weather monitoring
• Telecommunications & Broadcasting
• Commercial growth is focused on:
• DTH TV (Direct To Home: Sky TV)
• Phone, Fax, Video, Data services
• Mobile Communications
• VSAT & USAT
• Digital Radio
How to File for a Geo Position
• Only Allocated to National Governments
• Go to National Government
• Request Orbital Position (s)
• US Companies (Non Governmental Entities) work through FCC
• UK through UK Radiocommunications Agency
• Prepare ITU Paperwork
• File & Coordinate
• First Come, First Served = Priority!

Characteristics of Geostationary (GEO) Orbit Systems
• User terminals do not have to track the satellite
• Only a few satellites can provide global coverage
• Maximum life-time (15 years or more)
• Above Van Allen Belt Radiation
• Often the lowest cost system and simplest in terms of tracking and high speed switching
Features GEO
Height (Km’s) 36000
Time per orbit (Hrs) 24
Speed (Km’s / hr) 11000
Time Delay (ms) 250
Time in Site of Gateway Always
Satellite for Global Coverage 3
Challenges of Geostationary (GEO) Orbit
• Transmission latency or delay of 250 millisecond to complete up/down link
• Satellite antennas must be of larger aperture size to concentrate power and to create
narrower beams for frequency reuse
• Poor look angle elevations at higher latitudes
Geostationary Orbit Today

LAUNCH SYSTEM CONCEPTS
Satellites may be directly injected into low-altitude orbits, up to about 200 km altitude, from a
launch vehicle. Launch vehicles may be classified as expendable or reusable.
In addition shuttle was designed with the capability to retrieve satellite in low orbit. The shuttle
consists of a reusable orbiter which injects satellites to a LEO and re-enters the atmosphere,
landing as an aircraft. The orbitter itself is launched vertically with the help of two recoverable
solid rocket boosters. An expendable liquid hydrogen/ liquid oxygen tank furnishs propellant to
the three main engines. This tank is the only part of the shuttle that is not reused.
The shuttle can only launch satellite in LEO and therefore additional propulsion is necessary to
inject a satellite into the GEO. The heavy lift capability of the shuttle is effectively used for
carrying shuttle upper stages for the extra propulsion. Various types of upper stage have been
developed. These may be categorized as perigee stages and Integrated stages.

Typical of the expendable launchers are the U.S. Atlas-Centaur and Delta rockets and the
European Space Agency Ariane rocket. Japan, China, and Russia all have their own expendable
launch vehicles, and one may expect to see competition for commercial launches among the
countries which have these facilities. Until the tragic mishap with the Space Shuttle in 1986, this
was to be the primary transportation system for the United States. As a reusable launch vehicle,
the shuttle, also referred to as the Space Transportation System (STS), was planned to eventually
replace expendable launch vehicles for the United States (Mahon and Wild, 1984).
Three methods of launching a satellite: (1) Using apogee kick motor
(2) Using spacecraft thrusters
(3) Direct insertion to GEO
Using spacecraft thrusters
This method is employed since apogee kick motor imparts a vigorous acceleration. Spacecraft
thrusters are used to raise the orbit from GTO to GEO over a number of turns. There are two
thrusters on a satellite, one for more powerful orbit raising maneuvers and the other for on-orbit
maneuvers.
Direct insertion to GEO
Here the final stages of the rocket are used to place the satellite directly into GEO rather than the
satellite using its own propulsion system to go from GTO to GEO.
Where an orbital altitude greater than about 200 km is required, it is not economical in terms of
launch vehicle power to perform direct injection, and the satellite must be placed into transfer
orbit between the initial LEO and the final high-altitude orbit.
In most cases, the transfer orbit is selected to minimize the energy required for transfer, and
such an orbit is known as a Hohmann transfer orbit. The time required for transfer is longer for
this orbit than all other possible transfer obits. Assume for the moment that all orbits are in the
same plane and that transfer is required between two circular orbits, as illustrated in Figure. The
Hohmann elliptical orbit is seen to be tangent to the low altitude orbit at perigee and to the high-
altitude orbit at apogee. At the perigee, in the case of rocket launch, the rocket injects the satellite
with the required thrust into the transfer orbit. With the Space Transportation System (STS), the
satellite must carry a perigee kick motor which imparts the required thrust at perigee. At apogee,
the apogee kick motor (AKM) changes the velocity of the satellite to place it into a circular orbit
in the same plane. As shown in Figure, it takes 1 to 2 months for the satellite to be fully
operational.

The total energy, U of a satellite, for a two body system, is given by
Where m and v are the mass and velocity of the satellite respectively, and r is the distance from
geocenter, G is the gravitational constant and M the mass of the earth. To achieve a geostationary
orbit, the launch vechicle must be able to impart a velocity of 3070m/s at the GEO orbit height
about 42165 km from the earth. In an equipotential field, the maximum velocity increment, Δv,
which a launch vehicle of total mass m0 can impact may be given as
( )
vg = effective exhaust velocity of the gas, mf = mass of the expanded fuel
In order to maximize the ratio should be maximized. Therefore it is usual to launch
satrllites by means of multiple stage rockets, each stage being jettisoned after imparting a given
thrust. As mo is progressively reduced, succeeding stages of rockets need to impact
progressively lower thrust to achieve the desired orbit. The final velocity of the spacecraft is the
sum of the velocity increments of all the stages.
Orbital inclination is determined by the latitude of the launch station and is given by
( ) ( ) ( )
Where i – inclination, ,
Event Number Event
0 Vertical lift off
1 Guidance system begins tilting rocket towards east
2 First stage drop off
3 Second stage ignition
4 Horizontal insertion into parking orbit 185 to 250 km
5 Second and third stages fired at equator to acquire transfer orbit

Event Number Event
1 Velocity increment to acquire transfer orbit, satellite spun for stabilization,
attitude maneuvers done before apogee kick motor firing
2 Apogee kick motor fired to give necessary velocity increment, orbit ciculaized
and inclination reduced to near zero
3 Satellite despun
4 Three axis stabilization acquired
5 Minor orbit errors in orbit tested and position satellite on station
Throughout the launch and acquisition phases, a network of ground stations, spread across the
earth, is required to perform the tracking, telemetry, and command (TT&C) functions. Velocity
changes in the same plane change the geometry of the orbit but not its inclination. In order to
change the inclination, a velocity change is required normal to the orbital plane. Changes in
inclination can be made at either one of the nodes, without affecting the other orbital parameters.
Since energy must be expended to make any orbital changes, a geostationary satellite should be
launched initially with as low an orbital inclination as possible. It will be shown shortly that the
smallest inclination obtainable at initial launch is equal to the latitude of the launch site. Thus the
farther away from the equator a launch site is, the less useful it is, since the satellite has to carry
extra fuel to effect a change in inclination. Russia does not have launch sites south of 45°N,
which makes the launching of geostationary satellites a much more expensive operation for
Russia than for other countries which have launch sites closer to the equator.
Prograde (direct) orbits have an easterly component of velocity, so prograde launches gain from
the earth‟s rotational velocity. For a given launcher size, a significantly larger payload can be
launched in an easterly direction than is possible with a retrograde (westerly) launch. In
particular, easterly launches are used for the initial launch into the geostationary orbit. The
relationship between inclination, latitude, and azimuth may be seen as follows [this analysis is
based on that given in Bate et al. (1971)].
Launch Window: before the launch of a satellite is necessary to ensure that the launch time falls
within a “launch window”. This guarantees that the position of a satellite in respect of the sun is
favorable thus ensuring adequate power supply and thermal control throughout the mission.

Further, the launch must be so timed that the satellite is that the satellite is visible to the control
station during all the critical maneuvers. This set of conditions limits the launch time to certain
specified intervals, designed the launch window.
Propellant types:
 Chemical propulsion
 Solid propulsion
Consideration of chemical propulsion
Chamber Condition:
 Mass Balance
 Enthalpy Balance (Conversion of energy)
 Pressure Balance (Daltons Law)
 Chemical Equilibirium (Minimization of Gibbs Formula)
Rocket Performance:
 Equation of state (Ideal Gas law)
 Continuity Equation (Conversion of mass)
 Conversion of momentum
 Conversion of energy (First law of thermodynamics)
 Isotropic Expansion (Second law of thermodynamics)
Launch Vehicles
Arian:
 Arian Space – European consortium with European space agency and french space
agency
 Initiated in 1973, launch took place in 1979.
 Payload capacity of 1850 kg
 Ariane 2 & Ariane 3 has initiated in 1980
 Ariane 2 has a 2175 kg capacity into GTO (Geo Transfer orbit) & Ariane 3 has 2700 kg
capacity.
ATLAS:
 The atlas launch system is the product of the general dynamics space system division
 Atlas I, II & II A
 Payload capacity of 2500 kg
DELTA:
 Delta I & II
 Managed by McDonnell Douglay for NASA
 Launched in 1960
 2 stage mission & 3 stage mission

M- I & M – II:
 Launch vechicle of the national space development agency & Japan
 M-I has 3 stages, consisting of two liquid propellant stages and a composite solid
propellant 3 stage.
 Operational in 1988
 M – II has 2 stage liquid oxygen & liquid hydrogen rocket augmented by two solid
Orbit M-I M-II
GTO 1100 400
LEO 30 degree, 300 km 2900 9200
Sun synchronous, 700 km 1400 5000
Lunar or planetary 1400 2500
Long March:
 Developed by china initiated in 1956
 Long march 1,2,3,4 & 2E vehicles
 Since 1970, launches have placed more than 30 satellite into orbits
 E the most powerful in current production has a payload capability of 93000 kg into LEO
and 3370 kg into GTO.
PROTON:
 In Russia proton was developed between 1961 & 1965
 The proton has a capability of 20000 kg into LEO, 5500 kg into GTO, 2800 kg into sun
synchronous orbit.
SLV/ GSLV/ PSLV – ASSIGNMENT

Satellite Communication for BTech ECE students

More Related Content

Similar to Satellite Communication for BTech ECE students (20)

Recently uploaded (20)

Satellite Communication for BTech ECE students