SENSORS_AND_INST.UNIT_1_REG_17__Presentation.ppt
- 1. Measurement system comprises of sensors, transducers and signal processing devices. Sensors in manufacturing are basically employed to automatically carry out the production operations as well as process monitoring activities. Sensor technology has the following important advantages in transforming a conventional manufacturing unit into a modern one. 1. Sensors alarm the system operators about the failure of any of the sub units of manufacturing system. It helps operators to reduce the downtime of complete manufacturing system by carrying out the preventative measures. 2. Reduces requirement of skilled and experienced labours. 3. Ultra-precision in product quality can be achieved.
- 2. Sensor It is defined as an element which produces signal relating to the quantity being measured. Device which provides a usable output in response to a specified measurand.” Here, the output is usually an ‘electrical quantity’ and measurand is a ‘physical quantity, property or condition which is to be measured’. Thus in variable inductance displacement element, the quantity being measured is displacement and the sensor transforms an input of displacement into a change in inductance.
- 3. Transducer It is defined as an element when subjected to some physical change experiences a related change or an element which converts a specified measurand into a usable output by using a transduction principle. It can also be defined as a device that converts a signal from one form of energy to another form. Example: A wire of Constantan alloy (copper-nickel 55- 45% alloy) can be called as a sensor because variation in mechanical displacement (tension or compression) can be sensed as change in electric resistance. This wire becomes a transducer with appropriate electrodes and input-output mechanism attached to it. Thus we can say that ‘sensors are transducers’.
- 4. Sensor/transducers specifications Transducers or measurement systems are not perfect systems. Mechatronics design engineer must know the capability and shortcoming of a transducer or measurement system to properly assess its performance. There are a number of performance related parameters of a transducer or measurement system. These parameters are called as sensor specifications. Sensor specifications inform the user about deviations from the ideal behaviour of the sensors. Following are the various characteristics and specifications of a sensor/transducer system.
- 5. Basic components in a measurement system Basic components in a measurement system are shown below: It is also important to mention that a power supply is an important element for the entire system. Amplification and Conditioning
- 6. • Divided into two categories: static and dynamic characteristics. • Static characteristics refer to the comparison between steady output and ideal output when the input is constant. • Dynamic characteristics refer to the comparison between instrument output and ideal output when the input changes.
- 7. Transducers or measurement systems are not perfect systems. Mechatronics design engineer must know the capability and shortcoming of a transducer or measurement system to properly assess its performance. There are a number of performance related parameters of a transducer or measurement system. These parameters are called as sensor specifications. Sensor specifications inform the user about deviations from the ideal behaviour of the sensors. Following are the various specifications of a sensor/transducer system.
- 8. 1. Range The range of a sensor indicates the limits between which the input can vary. For example, a thermocouple for the measurement of temperature might have a range of 25- 225 °C. 2. Span The span is difference between the maximum and minimum values of the input. Thus, the above-mentioned thermocouple will have a span of 200 °C. 3. Error Error is the difference between the result of the measurement and the true value of the quantity being measured. A sensor might give a displacement reading of 29.8 mm, when the actual displacement had been 30 mm, then the error is –0.2 mm.
- 9. 4. Accuracy The accuracy defines the closeness of the agreement between the actual measurement result and a true value of the measurand. It is often expressed as a percentage of the full range output or full–scale deflection. A piezoelectric transducer used to evaluate dynamic pressure phenomena associated with explosions, pulsations, or dynamic pressure conditions in motors, rocket engines, compressors, and other pressurized devices is capable to detect pressures between 0.1 and 10,000 psig (0.7 KPa to 70 MPa). If it is specified with the accuracy of about ±1% full scale, then the reading given can be expected to be within ± 0.7 MPa. 5. Sensitivity Sensitivity of a sensor is defined as the ratio of change in output value of a sensor to the per unit change in input value that causes the output change. For example, a general purpose thermocouple may have a sensitivity of 41 μV/°C.
- 10. 6. Nonlinearity Figure 1. Non-linearity error
- 11. The nonlinearity indicates the maximum deviation of the actual measured curve of a sensor from the ideal curve. Figure 1 shows a somewhat exaggerated relationship between the ideal, or least squares fit, line and the actual measured or calibration line. Linearity is often specified in terms of percentage of nonlinearity, which is defined as: Nonlinearity (%) = Maximum deviation in input ⁄ Maximum full scale input. ----Equ. 1 The static nonlinearity defined by Equation 1 is dependent upon environmental factors, including temperature, vibration, acoustic noise level, and humidity. Therefore it is important to know under what conditions the specification is valid.
- 12. 7. Hysteresis Figure 2. Hysteresis error curve The hysteresis is an error of a sensor, which is defined as the maximum difference in output at any measurement value within the sensor’s specified range when approaching the point first with increasing and then with decreasing the input parameter. Figure2 shows the hysteresis error might have occurred during measurement of temperature using a thermocouple. The hysteresis error value is normally specified as a positive or negative percentage of the specified input range.
- 13. 8. Resolution Resolution is the smallest detectable incremental change of input parameter that can be detected in the output signal. Resolution can be expressed either as a proportion of the full-scale reading or in absolute terms. For example, if a LVDT sensor measures a displacement up to 20 mm and it provides an output as a number between 1 and 100 then the resolution of the sensor device is 0.2 mm. 9. Stability Stability is the ability of a sensor device to give same output when used to measure a constant input over a period of time. The term ‘drift’ is used to indicate the change in output that occurs over a period of time. It is expressed as the percentage of full range output. 10.Dead band/time The dead band or dead space of a transducer is the range of input values for which there is no output. The dead time of a sensor device is the time duration from the application of an input until the output begins to respond or change. 11.Repeatability It specifies the ability of a sensor to give same output for repeated applications of same input value. It is usually expressed as a percentage of the full range output: Repeatability = (maximum – minimum values given) X 100 ⁄ full range (2.1.2) 12.Response time Response time describes the speed of change in the output on a step-wise change of the measurand. It is always specified with an indication of input step and the output range for which the response time is defined.
- 14. Classification of sensors Sensors can be classified into various groups according to the factors such as measurand, application fields, conversion principle, energy domain of the measurand and thermodynamic considerations
- 15. Detail classification of sensors in view of their applications in manufacturing is as follows. A. Displacement, position and proximity sensors • Potentiometer • Strain-gauged element • Capacitive element • Differential transformers • Eddy current proximity sensors • Inductive proximity switch • Optical encoders • Pneumatic sensors • Proximity switches (magnetic) • Hall effect sensors B. Velocity and motion • Incremental encoder • Tachogenerator • Pyroelectric sensors
- 16. C. Force • Strain gauge load cell D. Fluid pressure • Diaphragm pressure gauge • Capsules, bellows, pressure tubes • Piezoelectric sensors • Tactile sensor E. Liquid flow • Orifice plate • Turbine meter F. Liquid level • Floats • Differential pressure G. Temperature • Bimetallic strips • Resistance temperature detectors • Thermistors • Thermo-diodes and transistors • Thermocouples • Light sensors • Photo diodes • Photo resistors • Photo transistor