Shape Memory Alloy Actuator forBio-medical application

Prashin Sharma et al. Int. Journal of Engineering Research and Applicationswww.ijera.com
ISSN: 2248-9622, Vol. 6, Issue 2, (Part - 3) February 2016, pp.60-66
www.ijera.com 60|P a g e
Shape Memory Alloy Actuator forBio-medical application
Prashin Sharma
MSc (Mechanical Engineering), Managing Director at Hindustan Security Force, India
Past Graduate StudentDepartment of Mechanical engineering,Carnegie Mellon University, PA – 15213
Abstract
In this paper various applications of shape memory alloys (SMA) in bio-medical field based upon their material
properties are discussed, and a novel SMA spring actuator design for biopsy is proposed. Design parameters
such as spring configuration, wire diameter required for designing the actuator were defined and obtained
through experiments. Finally, itconcludeswith the possibility of using SMA spring for high force compact
system.
Keywords: Shape memory alloy, biopsy, bio-medical, actuator
I. INTRODUCTION
Shape Memory Alloys have been at the forefront
of research for the past decade. They are becoming
an integral part of design of a variety of new medical
products. A few common examples of shape memory
alloys are Nickel-titanium, Copper-aluminum-
nickel,Copper-zinc-aluminum etc. Shape memory
alloys are a unique class of shape memory materials.
SMAs are metallic alloys that have the ability to
„remember‟ and return to their predetermined shape
when heated which involves the rearrangement of
particles within the crystal structure of the solid. An
increase in temperature can result in shape recovery
even under high applied loads therefore resulting in
high actuation energy densities. As illustrated in the
stress- temperature graph fig 1, Ms and Mf designate
the martensite start and finish temperatures
respectively, while As and Af represent the austenite
start and finish temperatures respectively. Upon
cooling in the absence of applied load the crystal
structure changes from austenite to martensite. The
phase transition from austenite to martensite is
termed as forward transformation. The arrangement
of variants occur
Fig 1. GeneralTemperature vs strain diagram of
shape memory alloy
such that macroscopic shape change is negligible.
The phase transition from austenite to martensite is
termed as forward transformation. When the material
is heated from martensitic phase it slowly transforms
into the austenite phase [As] and this transition is
called as reverse transition during which there is no
associated phase change. If a mechanical load is
applied the material in twinned martensitic phase (at
low temperature), it is possible to detwin the
martensite by reorienting a certain number of variants
resulting in macroscopic shape change. A subsequent
heating of the SMA to a temperature above Afwill
result in reverse phase transformation (from
detwinned martensite to austenite) and will lead to
complete shape recovery. Cooling back to
temperature below Mf (forward transformation) leads
to formation of twinned martensite again with no
associated shape change observed.
II. SMA PROPERTIES
The unique property of shape recovery of shape
memory alloys is possible due to the solid state phase
transformation between the low temperature
martensite[M] phase and the high temperature
austenite[A] phase and they only differ in their
crystallographic structure. This ability is known as
shape memory effect.
Fig 2. Different phases of shape memory alloys
There are two types of shape memory effect.
 One way effect: When the SMA is deformed
within its pseudoplastic strain range and then
RESEARCH ARTICLE OPEN ACCESS

brought back to its original shape by heating, this
is known as the one way effect.
 Two way effect: This is associated with a shape
change upon heating and cooling without any
application of external load. Shape change is less
pronounced than the one way effect.
Fig 3. Illustration of one and two way shape memory
effect
Fig 4. Illustration Pseudo elastic property of SMA
Pseudo elasticity is another unique property of
shape memory alloys. It occurs when in the austenite
phase, it is possible for the SMA to undergo a phase
change at a constant temperature. This is achieved by
increasing the load acting on the SMA while at a
constant temperature greater than Af, and as
illustrated in the graph, the phase change into
martensite takes place.
III. SMA APPLICATIONS
Nitinol is being used in the military, medical,
safety, and robotics applications. Many of the current
applications of Nitinol have been in the field of
medicine.
Fig 5. Illustration of forceps
Anchors with Nitinol hooks are used to attach
tendons to bone. An orthodontic wire made out of
Nitinol reduces the need to retighten and adjust the
wire. These wires also accelerate tooth motion as
they revert to their original shapes. Nitinol eyeglass
frames can be bent totally out of shape and return to
their parent shape upon warming. Nitinol needle wire
localizers are used to locate and mark breast tumors
so that subsequent surgery can be more exact and less
invasive, utilizing the metal's shape memory
property. Nitinol is also used for guiding catheter.
One of the interesting applications of SMA is in
the atrial septal-defect occlusion system (ASDOS)
(OsypkaMedizintechnik, Rheinfelden, Germany).
This device is the first to allow nonsurgical repairs of
occlusions, or holes, in the atrial wall of the heart.
The actual device comprises two small umbrellas
consisting of five nitinol wire loops supporting webs
of microporous polyurethane (see fig 6). The two
umbrellas are passed into the body while folded into
two catheters, and are positioned one each on either
side of the defect area. A guidewire passing directly
through the hole is used to ensure that the two
catheters and umbrella devices are positioned
correctly. Once positioned, the umbrellas are pushed
forward from their catheters and screwed together
using a special torquing catheter. The resulting
sandwich forms a patch, occluding the atrial defect.
Available umbrella diameters range from 20 to 65
mm. [1]
Fig 6.The atrial septal-defect occlusion device is
used to seal holes in the heart wall.
The extraordinary compliance of nitinol clearly
makes it the metal that is most similar mechanically
to biological materials. This improved physiological
similarity promotes bones ingrowth and proper
healing by sharing loads with the surrounding tissue,
and has led to applications such as hip implants, bone
spacers (see fig 7), bone staples, and skull plates.
Fig 7. Spinal vertebrae spacer shown in the
martensitic state (left) and deployed superelastic state
(right)

The most celebrated super elastic application of
shape memory alloys in medical devices are self-
expanding stents, used to brace the inside
circumference of a tubular passage such as an
esophagus, bile duct, or blood vessel (see fig 8).
Probably the most interesting area of application is in
the cardiovascular system, as a follow-up to balloon
angioplasty. The placement of a stent has been shown
to significantly decrease the propensity for restenosis.
Like the vena cava filter, these devices are generally
permanent implants, deployed through a catheter
using the shape-memory effect.
Fig 8. Stents made from nitinol tubing
Advantages
 Bio-compatibility
 Diverse fields of application
 Good mechanical properties
Disadvantages
 Expensive to manufacture
 Poor fatigue properties
 Hysteresis
IV. BIOPSY FORCEPS
Biopsy forceps (fig. 5) is a device commonly
used for tissue sampling during
esophagostroduodenoscopy which is a
diagnosticendoscopic procedure that visualizes the
upper part of the gastrointestinal tract up to the
duodenum. It is considered a minimally invasive
procedure since it does not require an incision into
one of the major body cavities and does not require
any significant recovery after the procedure (unless
sedation or anesthesia has been used). The
advantages of using forceps is its small size which
causes less discomfort to the patients, also multiple
tissue samples can be collected during single
operation. A test rig was designed to simulate the
motion of the forceps while performing biopsy and
measure the forces applied by the operator. Force
required for cutting the tissue sample is an important
parameter for designing the SMA actuator.
A. Test Rig Design
Tomeasure the forces required while performing
biopsy a test rig was designed with two degrees of
freedom or two axis.Axis 1 was used to control
opening and closing of the forceps and axis 2 was
used for tearing the biopsy sample out of the tissue
when the jaws of the forceps was fully closed as
shown in fig 9.
Fig9. Test rig to measure the forces for performing
biopsy using forceps
Forceps which was used in this experiment is Radial
Jaw3 manufactured by Boston Scientific. Two linear
stages MFA CC Linear Miniature Series made by
Newport were used for actuating the two axes. The
maximum linear speed attainable by the linear stages
was 3mm/s. To measure the forces applied two load
cells, MLP10 product of Transducer technology,
were used, one with each axis placed coaxially along
the axis of applied force. Pig esophagus was used as
the tissue sample for performing the biopsy.
B. Results
The linear stages were operated at their maximum
linear speed while performing the experiment. The
forceps was fully open when it was pressed against
the tissue sample, also the full area of the forceps was
in contact with the tissue sample before closing the
forceps. Successful biopsy wasobtained and results
are illustrated in the graph.
Fig10. Forces measured from axis 1 while
performing biopsy
The nature of the graph is similar to the
experiments performed by earlier published results
[1] using porcine liver. The amount of force required
for performing biopsy was 28 N as shown by
highlighted peak in the graph. From the geometry of
forceps the tip velocity of 6mm/s was achieved while
closing the forceps. The amount of force applied to
axis 2 for tearing the sample from the tissue was
around 6.2N as illustrated in fig 11.

Fig 11.Forces measured from axis 2 while
performing biopsy
V. ACTUATOR DESIGN
We will be designing an actuator using SMA to
actuate the axis 1, which is used for opening and
closing the radial jaw or forceps for performing
biopsy.
A. Design Parameters
From the experiment conducted, application and
published papers [2] various parameters for design of
the actuator were identified. They are as follows:
i) Tip velocity of the forceps, whichaffects the
local effective modulus (LEM) of the tissue.
LEM provides quantitative estimate of the tissue
deformation resistance immediatelypreceding the
extension of the cut [3].
ii) Force required to be generated by the actuator.
iii) Since forceps are used for minimal invasive
surgery, the actuator should be as compact as
possible to reduce the discomfort to the patient.
iv) The actuator should be bio-compatible.
v) Power requirements of the actuator.
B. Actuator Design
Based on the parameters defined above, a novel
actuator was conceptualized which could provide the
required forces and velocity for performing biopsy.
Fig 12. Actuator concept
The actuator uses SMA spring and a steel spring.
SMA 1 which is attached to a ferromagnetic material
is used as a latch. The steel spring is attached to a
magnet as shown in fig.12 which is denoted by M.
SMA 2 is placed in parallel configuration to the steel
spring to dampen the vibrations along with providing
some force when closing the forceps. Magnet M is
connected to the 5 bar mechanism through a rigid
link. 5 bar linkage mechanism is used to transmit
forces and motion in opposite direction of that of the
magnet, to the forceps. Thus when magnet moves to
the right the forceps closes and when magnet moves
to the left the forces opens. The basic principle of
actuator is that, electric energy provided to the shape
memory alloy spring is stored as potential energy
(PE) in the steel spring until the point when the
spring force is greater than magnetic attractive force
acting between the ferromagnetic material and
magnet. The stored PE of the steel spring is used to
actuate the forceps.
Working of the actuator is illustrated in the figures
below.

Fig 13. Steps involved in actuation
SMA 1 is actuated by passing current through it
as shown in Step 1. Since SMA 1 and steel spring are
coupled my magnetic attractive force acting between
the ferromagnetic material and magnet, thus resulting
in deflection of spring as SMA 1 contracts due to
electrical heating. In this step the forceps open and
pushed against tissue. SMA 1 continues to contract
until the magnet detaches from the ferromagnetic
material as shown in Step 3. As the magnet M moves
toward right SMA 2 is actuated so that it provides
added force to spring force to the link connected to 5
bar linkage mechanism, also to dampen the vibrations
of spring. As a result the forceps tends to close biting
the tissue sample. At the end of step 5 the forceps is
completely closed having the biopsy sample inside it.
Current supplied to SMA 1 is stopped and the forceps
is pulled out to tear the sample still attached to tissue.
In step 7 current supplied to SMA 2 is also stopped
and the actuator returns back to its original position
as shown in step 1.
Table 1Various calculated dimensions of SMA1
No of
SMA
springs
(n)
Load on
each
SMA
spring,
p(N)
SMA wire
diameter,
d(mm)
SMA
spring
diameter,
D(mm)
High
temperature
s spring rate,
𝑲 𝒉(N/mm)
Low
temperature
s spring rate,
𝑲𝒍(N/mm)
Heating
time for
each SMA
spring,
𝒕 𝒉 (s)
Cooling
time for
each SMA
spring,
𝒕 𝒄 (s)
Single spring
1 30 2.4 14.5 10.0344 1.105832 3207 355
Multiple springs in parallel configuration
2 15 1.7 10.2 5.017202 0.552916 747 191
5 6 1.1 6.5 2.006881 0.221166 89 91
8 3.75 0.9 5.1 1.2543 0.138229 18 64
10 3 0.757 4.5 1.00344 0.110583 1.8 53
Concentric spring ( varying spring index)
SMA
Spring
indexc
Load on
each
SMA,
spring
p1/p2(N)
SMA wire
diameter,
d1/d2(mm)
SMA spring
diameter,
D1/D2(mm)
High
temperatu
res spring
rate,
𝑲 𝒉𝟏/ 𝑲 𝒉𝟐
(N/mm)
Low
temperature
s spring rate,
𝑲𝒍𝟏/𝑲𝒍𝟐
(N/mm)
Heating
time for
each SMA
spring,
𝒕 𝒉𝟏
/𝒕 𝒉𝟐 ×
𝟏𝟎 𝟑
(s)
Cooling
time for
each SMA
spring,
𝒕 𝒄𝟏/𝒕 𝒄𝟐 ×
𝟏𝟎 𝟑
(s)
10 18 /11.7 2.4/1.8 24/18.5 5.6/3.6 0.61/0.39 2.7/1 0.3/0.2
8 19.2/10.8 2.2/1.7 17.2/13 6/3.4 0.67/0.38 2/0.6 0.6/0.17
5 22/7.9 2/1.2 10/6 7.7/2.7 0.85/0.3 1.2/0.1 0.13/.1
C. Design Calculations
We have designed SMA 1 spring which is one of
the most important component of the whole system.
Various assumptions were taken into considerations
while design calculations of shape memory alloy
spring. The maximum force which acts on SMA 1 is
in step 3 just before magnet and the ferromagnetic
material detach. This design force is assumed to be
around 30 N which is required to cut the tissue. SMA
spring is designed in the linear region of the stress
strain curve. The heating and cooling time constant
calculated for the shape memory alloy spring was
based on still air conditions. Also the temperature
inside the human body was considered to around
37℃. The high and low temperature shear modulus
was assumed to be 𝐺ℎ = 24500 Mpa and 𝐺𝑙=2700
Mpa. Shear stress was assumed to be 𝜏 𝑐= 100 Mpa.
The current provided to sma spring is considered as
0.8 amps. Various temperatures which were
described in section I and required for calculations
for Ni-Ti-Cu are 𝐴𝑓 = 65℃ , 𝑀𝑠 = 59℃and𝑀𝑓 =
43℃. High temperature shear strain is defined by
𝛾ℎ = 𝜏 𝑐 𝐺ℎ = 0.408 % and the low temperature shear
strain is limited to𝛾𝑙 = 1.5 %. Different
configurations of SMA spring were taken into
account such as having single spring, multiple
springs in parallel configurations and concentric
spring design was also considered. Since concentric
spring have uneven load distribution as compared to

multiple springs in parallel configuration different
wire diameters were obtained for each spring.
(a) (b)
Fig 14. (a) Single spring configuration, (b) concentric
spring configuration
The actuator size is constrained to a cylinder with
dimensions of 10 mm radius and 30mm length. The
spring index chosen for design of single and multiple
spring configuration is 6.The diameter of the SMA
spring is defined by the following formula,
𝑑 =
8𝑊𝑝𝑐
𝜋𝜏 𝑐
Where,
d= diameter of the wire (mm), p= load applied (N),
c= spring index,𝜏 𝑐= shear stress.
No. of turns for the spring is defined by,
𝑛 = 𝑑 × 𝑠𝑡𝑟𝑜𝑘𝑒/(𝜋 × 𝐷2
× 𝛾𝑆)
Where,
𝛾𝑆= shear strain associated with stroke
Stroke length required is 5mm
The high temperature and low temperature spring
rates are defined by the following formulae
respectively,
High Temperature stiffness,
𝐾 𝐻 =
𝐺 𝐻 𝑑4
8𝑛𝐷3
Low Temperature stiffness,
𝐾𝐿 =
𝐺 𝐿 𝑑4
8𝑛𝐷3
Where,
𝐺 𝐻= High temperature shear modulus,
𝐺 𝐿 = Low temperature shear modulus,
n = number of turns
Since still air condition operation were assumed the
heating time constant is assumed as follows,
𝐽 𝐻 = 12.06 + 8011.3 × 𝑑2
𝑇 𝑚𝑎𝑥 = 0.645 ×
𝐼
𝑑
+ 6.18 × 10−3
𝐼2
𝑑2
Where,
I = current in amp,
𝑇 𝑚𝑎𝑥 = maximum temperature where the rate of heat
generated by the current is equal to the rate of heat
loss by convection.
The time required for heating the wire is given by the
formula,
𝑡ℎ = 𝐽 𝐻 𝑙𝑛
𝑇 𝑚𝑎𝑥 − 𝑇𝐴
𝑇 𝑚𝑎𝑥 − 𝐴𝑓
+ 5.064
× 107
𝑑4
𝐼2
𝑇 𝑚𝑎𝑥 − 𝐴𝑓
The cooling time constant is assumed as follows,
𝐽𝑐 = 13.256 + 12068.6 × 𝑑2
And time required for the SMA to cool down is given
by the formula
𝑡 𝑚𝑎𝑥 = 𝐽 𝐻 𝑙𝑛
𝑀𝑓 − 𝑇𝐴
+
28.88
𝑀𝑠 − 𝑇𝐴
Where,
𝑀𝑓 = Martensites finish temperature.
For concentric SMA spring design the load
distribution on each spring is directly proportional to
the wire diameter, thus the ratio yields the following
relationship,
𝑊1
𝑊2
=
𝑑1
𝑑2
2
And the diameter of the wire are related through the
following relation which is a function of spring
index.
𝑑1
𝑑2
=
𝐶
𝐶 − 2
D. Results
Based on the above mentioned formulae Table 1
was created for different configurations. It could be
inferred from the table that for single SMA spring
configuration the wire diameter is 2.4mm and
average diameter of the spring is 14.5 mm which
more than constraints hence it is ruled out. As we go
for multiple springs in parallel configuration though
the heating and cooling time of each spring
decreases, it requires a larger area to be installed. For
the concentric spring as the spring index in decreased
till c=5, SMA spring dimensions are within the
dimensional constraints. But the heating and cooling
time are quite high.
VI. CONCLUSION
From the calculations it can be concluded that
SMA spring with concentric configuration can be
used as actuator for biopsy forceps but there is a
tradeoff between the following parameters which are
size, force and displacement. For using concentric
SMA springs though the diameter of SMA wire is
quite high custom made springs could be used also
the heating and cooling conditions can be quicken by
increasing current supplied and forced cooling of the
SMA spring by circulating air, respectively.

ACKNOWLEDGEMENTS
I would like to thankProf. MetinSitti (CMU) who
provided insight and expertise that greatly assisted
during the course of this research. I, would also like
to thank Paul Glass (CMU, PhD. Candidate) for
assisting with lab set up for performing experiments.
REFERENCES
[1] www.devicelink.com
[2] “Mobile in Vivo biopsy robot“, Mark
E.Rentscheler, Jason Dumpert, Stephen R.
Platt, Dmitry Oleynikov, Karl Iagnemma,
2006 IEEE ICRA.
[3] “Development of a Surgical Simulator for
Laparoscopic Esophageal Procedures”,
Changmok Choi, Hyonyung Han, Bummo
An, and Jung Kim, Proceedings of the 28th
IEEE, EMBS Annual International
Conference
[4] “Modeling Soft-Tissue Deformation Prior to
Cutting for Surgical Simulation: Finite
Element Analysis and Study of Cutting
Parameters “, TeeranootChanthasopeephan,
Student Member, IEEE, Jaydev P. Desai*,
Member, IEEE, and Alan C. W. Lau, IEEE
Transactions on Biomedical Engineering,
Vol. 54, No. 3, March 2007
[5] Actuator design using shape memory alloys
by Tom Waram
[6] Engineering Aspects of shape memory
alloys by Duerig Melton StockelWayman.
[7] Machine design, by R.S.Khurmi, J.K.Gupta

Shape Memory Alloy Actuator forBio-medical application

More Related Content

Viewers also liked (19)

Similar to Shape Memory Alloy Actuator forBio-medical application (20)

Recently uploaded (20)

Shape Memory Alloy Actuator forBio-medical application