Simulation for Automation of Manufacturing, Filling And Capping The Bottles

International
OPEN ACCESS Journal
Of Modern Engineering Research (IJMER)
| IJMER | ISSN: 2249–6645 | www.ijmer.com | Vol. 7 | Iss. 2 | Feb. 2017 | 62 |
Simulation for Automation of Manufacturing, Filling And
Capping The Bottles
1
Avunoori Anudeep Kumar, 2
Murahari Sunil Kumar
Assistant Professor, Dept. Of Mechanical Engineering, Institute Of Aeronautical Engineering,
Hyderabad, Telangana, India.
I. INTRODUCTION
The small scale industries require large amount of labour to perform the operations such as
manufacturing of bottles, filling with liquid and capping the bottles. To increase the production rate the low cost
industrial automation process [1] is best suitable for small scale industries [2]. This is achieved through electric
circuits, relays, pneumatic actuators, limit switches, sensors, solenoid valves and Electropneumatics which are
controlled by electrical impulses [3]. The sequence of operations are such as automatic clamping, unclamping,
injecting the molten material, filling [4] and capping process of the bottles [5] which is tested and simulated by
using Fluidsim Pneumatic simulation software. The Fluidsim Pneumatic Simulation software supports learning,
educating, and visualizing pneumatic knowledge. The Pneumatic components which are explained with textual
descriptions, figures, animations and its working principles. The user will quickly learn to draw and simulate
electro-pneumatic circuit diagram.
II. FLUIDSIM PNEUMATIC SIMULATION SOFTWARE
Fluidsim Pneumatics is a teaching tool for simulating pneumatics basics and runs using Microsoft
Windows. It can be used in the combination with the Festo Didactic training hardware or independently.
Fluidsim was developed as a joint venture between the University of Padeborn, Festo Didactic Company and
Art Systems software in Padeborn. A major feature of Fluidsim is its close connection with CAD functionality
and simulation. Fluidsim allows DIN-compliant drawing of electro pneumatic circuit diagrams and can perform
realistic simulations. Simply stated, this eliminates the gap between drawing of a circuit diagram and the
simulation of the related pneumatic system. The CAD functionality of Fluidsim has been specially tailored for
fluidics.
2.1. Fluidsim Toolbar Menu
Stat Fluidsim via the Start Menu under Program Files/FestoDidactic After a few seconds the main window from
Fluidsim should appear on the screen as shown in below Fig 1.
Fig 1: Fluidsim window.
ABSTRACT: The industries require large amount of labour to increase the production rate. The low
cost industrial automation process is best suitable for small scale industries to increase the production
rate of bottle manufacturing, filling with liquid and capping the bottles. In the present work the electric
circuits for the above process have been designed and simulated. The sequence of operations are such as
automatic clamping, unclamping, injecting the molten material, filling and capping process of the
bottles, which is achieved through the use of simple devices like limit switches, relays, electrical
controls, pneumatic actuators and sensors. The sequence of operation is tested and simulated by using
Fluidsim Pneumatic simulation software.
Keywords: Fluidsim Pneumatic simulation software, pneumatic actuators, relays, sensors.

Simulation For Automation Of Manufacturing, Filling And Capping The Bottles
The left-hand side shows the component library of Fluidsim in its hierarchical view, it contains
pneumatic, electrical and digital components for the designing new circuit diagrams. Using the menu bar at the
top of the window, you may access all functions provided for designing and simulating circuit diagrams. The
toolbar below allows convenient access to frequently used menu functions.
The toolbar contains the following nine group of functions.
2.1.1 Creating New Circuit
Creating new circuit diagrams, previewing a circuit diagram, opening and saving circuit diagrams
2.1.2 Print
.
Printing the contents of the window, for example circuit diagrams and component photos.
2.1.3 Editing Circuit
Editing circuit diagrams they are undo, cut, copy and paste respectively.
2.1.4 Alignment of Components
Alignment of components.in align left, align horizontally centered, align right, align top, align vertically
centered, align bottom respectively.
2.1.5 Rotate and Mirror
The first icon is used for Rotate and next two icons are used to mirror. Horizontally and vertically respectively.
2.1.6 Grid
By this option the grid lines appear on the screen.
2.1.7 Zoom
Zooming in and zooming out of circuit diagrams, component pictures, and other windows the icons
shown are used for standard size, previous view, fit to window, zoom by rubber band, zoom in and zoom out
respectively.

2.1.8 Superficial Circuit Checking
It Superﬁcial checks whether the there are any openings of the. Ports in the pneumatic circuit and
detection of short circuit in the electrical circuit.
2.1.9 Simulation
Simulation of circuit diagrams is done by this option. The icons shown represent the buttons of stop,
start, pause, reset, single step, simulate until state change and next topic respectively.
2.2 Creating Circuits
Create an empty drawing area by clicking on new icon or under File menu click New to open a new
window. The following window appears as in Fig 2.
Fig 2: New file window
While in basic mode, you will see the available component groups in the hierarchical view of the
component library. To list the components of a group, you may list off the group by clicking it. For a better
overview you may also hide non-required elements and subgroups by once more clicking and hence closing the
hierarchy. Component groups may often contain further subgroups that may also be listed off or closed.
To list off a group including all of its subgroups, you may hold the Shift-Key while clicking. This will
reduce your efforts to list off each subgroup. You may similarly use the Shift-Key to close all subgroups of a
superordinate group.
Press the Shift-Key, hold it and click “Pneumatic” The entire group of pneumatic components will be
listed off. Using the scrollbars, you may browse through the component library to the left and right or up and
down as shown in Fig 3.

Fig 3: Components library
Using the mouse and “drag-and-drop” you may drag components from the component library to the
drawing area. Move the mouse cursor to a component in the library, more speciﬁcally to the cylinder. Press the
left mouse button. While continuing to hold down the button, move the cursor. The cylinder is then highlighted
(selected) and the mouse cursor changes to a four way directional cross the components outline moves with the
mouse cursor. Move the cursor to the drawing area and release the button on the mouse. This action places the
cylinder in the drawing area as shown in Fig 4.
Fig 4: Dragging selected components.
In this way it is possible to “drag” each component from the component library and place it in the
desired position in the drawing area. In the same way it is possible to rearrange components already in the
drawing area.Arrange all the cylinders and components required for the circuit and connect the ports from air
supply to the cylinders, and remaining components like direction control valves, flow control valves etc. Double
click the valve to assign an operation mode to it. A dialog box appears as shown in Fig 5.
Fig 5: Configure a way valve.

2.3 Description of the Dialog Box for Configure Way Valve
2.3.1 Left/Right Actuation
For both sides the actuation modes of the valve can be defined individually; it can be one or more of the
categories “Manually”, “Mechanically”, or “Pneumatically or Electrically”. An operation mode is set by
clicking on the down-arrow at the right-hand side of the list and selecting a symbol. If for a category no
operation mode is desired, simply choose the blank symbol from the list. Moreover, for each side of the valve
the attributes “Spring-returned” and “Piloted” can be set.
2.3 2 Description
Enter here a name for the valve. This name is used in the state diagram and in the parts list state
diagram and in the parts list.
2.3 3 Valve Body
A configurable valve has at most four positions. For each of the positions a valve body element can be
chosen individually. Such an element is set by clicking on the down arrow at the right-hand side of the list and
selecting a symbol. If for a position no element is desired, simply choose the blank symbol from the list. The
valve may be marked “Reversible” to indicate that there is no particular direction of flow.
2.3 4 Initial Position
This button defines the valve’s initial position (normal position or neutral position), which is the
position without having any operation applied to the valve. Note that this setting is only exploited if it physically
does not contradict a spring returned setting.
2.3 5 Standard Nominal Flow Rate
This is where you define the standard nominal flow rate of the valve.
2.4 Configurable Symbols
Fluidsim is capable of simulating a vast number of different cylinders and valves. The combination of
all part designs and functional types would lead to displaying many thousands of symbols. Therefore there are
some common part designs in the component library, configurable and representative components. In order to
adapt a cylinder or a way valve, drag one of these representatives in the circuit and open the status dialog. Here
the settings helps in defining layout and function of the component.
2.5 Configure Cylinders
Double-click the cylinder to define part design, parameter and external influence of a cylinder. The
status dialog of the cylinder will open. The dialog consists of several registers, providing a convenient overview
despite the vast number of settings.
2.5.1 Register “Configuration”
Fig 6: Configure cylinder

2.5.2 Description of the Configure Cylinder Dialog Box
2.5.2.1 Component Description
The user can enter a description for the cylinder into the text field, it will show in the state diagram and in the
parts list.
2.5.2.2 Cylinder type
Cylinder type (single-acting, double-acting, spring return)
2.5.2.3 Piston rod type
Piston rod type (quantity, part design, magnet coupling, slide unit)
2.5.2.4 Properties
More properties of the cylinder (end position cushioning, sensing).The label you may define at “sensing” serves
as an interconnection with the displacement encoder.
2.5.2.5Mirror
This is where you may define whether the cylinder will be mirrored horizontally or vertically.
2.5.2.6 Register “Actuating Labels”
In this dialog box define new actuating labels or change existing ones as shown in below Fig 7.
Fig 7: Actuating labels for cylinders
In the same way Fluidsim allows to create pneumatic circuit diagrams, the software also allows to design
electrical circuits. The components for the electrical circuits can be found in the component library and dragged
from there to be inserted on the drawing area. Electrical components are connected in the same way thus the
fluidic components done.
2.6 CONFIGURE SOLENOID VALVES Each solenoid valve should be labelled without labelling the
simulation does not take place. The following dialog box appears as in Fig 8.
Fig 8: Configure Valve solenoid

2.6.1 Description of Configure Valve Solenoid Dialog Box
2.6.1.2 Label
This text ﬁeld gives the label its name. A label can be up to 32 characters in length consisting of letters,
numbers, and symbols. Enter a name for this label, for example “Y1”. Double click on the outside of the valve
solenoid to open the dialog box for the label name input the same label name as for the solenoid, for example
“Y1”. The solenoid is now linked to the valve.
III. SIMULATION FOR AUTOMATION OF MANUFACTURING, FILLING AND
CAPPING THE BOTTLES
For automation of bottle manufacturing filling and capping process the sequence consists of Clamping
the die block, moving the ram of injection moulding machine downwards, wait for a while and unclamp the die
block, clamp the bottle, move the filler into the bottle, open the nozzle valve, after filling, close the nozzle,
unclamp the bottle, clamp the bottle, move the capping motor downwards, after capping, move the capping
motor upwards and unclamp the bottle. Thus consists of mainly three sections bottle manufacturing, filling and
capping of the bottles.
That’s the required sequence for overall process is A+B+B-A-C+D+V+V-D-C-E+F+F-E-
The interlocks occurs between B+ and B-, similarly in V+ and V-, F+ and F- to remove these interlocks relays
are used. The total sequence is divided in to three operations. They are mentioned below.
a) Automation for manufacturing of the bottles by Injection Moulding machine.
b) Automation of filling the bottles.
c) Automation of capping the bottles.
3.1 Sequence for Automation of Bottle Manufacturing Process
For automation of the bottle manufacturing process the sequence consists clamping of the die block,
move the ram downwards and inject the molten material in to die block, move the ram upwards, wait for a while
and unclamp the die the bottle is ejected on to the conveyor.
For automation of this process the sequence is A+B+B-A-.
3.1.1 Design of Electric Circuit for Automation of Bottle Manufacturing Process
a) Connect the start button and solenoid valves A+, B+ to the NC of the relay K.
b) Connect the solenoid valves B-, to the NO of relay K.
c) Connect TB- NO with timer T as shown in circuit.
d) Connect the timer switch to the solenoid valve A-.
e) Connect the TB+ to relay K.
f) Hold the relay K with K and TA- NC.
g) The circuit is designed as per the shown fig below.
3.1.2 Simulation of Electric Circuit for Automation of Bottle Manufacturing Process
The design of electropneumatic circuit is drawn in the Fluidsim software the pneumatic circuit is drawn
from the components under the pneumatic library and the electric circuit is drawn from the components under
the electrical controls library. After completing the circuit. Then press the simulation button and press the start
button in the circuit and the simulation starts as shown in Fig 9.
Fig 9: Simulation of electric circuit for automation of bottle manufacturing process.

3.2 Sequence for Automation of Filling the Bottles with Liquid
For automation of the filling process the sequence consists of clamp the bottle, inject the filler in to the
bottle, open the valve, fill the bottle up to required quantity, close the nozzle valve, eject the filler from the
bottle, and unclamp the bottle
The sequence for this process is C+D+V+V-D-C-
Cylinders C, D, V are used for clamping of the bottle, movement of the filler, and nozzle valve open or close
respectively.
3.2.1 Design of Electric Circuit for Automation Process of Filling the Bottles
a) The sensors have three terminals one is connected to +ve, -ve and the other is output.
b) The output of sensor 1 is connected to the relay K2 and the output of the sensor s2 is connected to relay K3.
c) The relay K2 is hold with K2 NO (Normally Open) and TV+ NC (Normally Close).
d) The relay K3 is hold with K3 NO and TC- NC
e) The solenoid C+ is connected to K2
f) TC+ NO and the solenoid D+ are connected to K2
g) TD+ NO and solenoid V+ are connected to K2.
h) The solenoid V- is connected to K3.
i) TV- NO and the solenoid D- are connected to K3.
j) TD- and the solenoid C- are connected to K3.
3.2.2 Simulation of Electric Circuit for Automation Process of Filling the Bottles.
The design of electropneumatic circuit for filling process is drawn in Fluidsim software and start the
simulation by pressing the simulation button and the simulation starts when the sensors are activated as shown
in Fig 10.
Fig 10: Simulation of electric circuit for automation process of filling the bottles
3.3 Sequence for Automation of Capping the Bottles
For automation of capping process the designed sequence is clamp the bottle, movement of the capping
motor, unclamp the bottle. For automation of this process the designed sequence is E+F+F-E-
Two double acting pneumatic cylinders E and F are used for clamp the bottle and to the capping motor
respectively.
3.3.1 Design of Electric Circuit for Automation Process of Capping the Bottles
a) The +ve and –ve terminals of the sensor3 and sensor 4 are connected to power supply and ground.
b) The output terminals of the sensor 3 is connected to relay K4 and the output of the sensor 4 isconnected to
relay k5.
c) The relay K4 is hold with k4 and TF+ NC.
d) The relay K5 is hold with K5snd TE- NC.
e) The solenoid E+ is connected to K4.

f) TE+ and solenoid F+ is connected to K4
g) The solenoid F- is connected to F
h) The solenoid E- and TF- are connected to K5
3.3.2 Simulation of Electric Circuit for Automation Process of Capping the Bottles.
The design of electropneumatic circuit for capping process is drawn in Fluidsim software and start the
simulation by pressing the simulation button and the simulation starts when the sensors are activated as shown
in Fig 11.
Fig 11: simulation of electric circuit for automation process of capping the bottles
IV. CONCLUSION
The electric circuits are designed and the sequences of operations are tested by using Fluidsim
Pneumatic simulation software. The sequence of operations are such as automatic clamping, de-clamping,
injecting the molten material, filling and capping process of the bottles are essential in industries to increase its
production rate. This is achieved through the use of simple devices like limit switches, relays, sensors,
pneumatic actuators and electrical controls. The automation process has preciseness and accuracy in their
operations, which is controlled through its controllers. The automation process helps in reducing the time taken
for the process to be completed and helps at low cost to yield higher productivity. The bottles with defect are to
be eliminated from the conveyor by using Machine Vision.
REFERENCES
[1]. Ribeiro.R, Dias.O.P, Teixeira.I.C, "Hardware/software solution for the automation and real-time control of a wine
bottling production line," Emerging Technologies and Factory Automation, 2003. Proceedings. ETFA '03. IEEE
Conference, vol.1, no., pp.110, 115 vol.1, 16-19 Sept. 2003
[2]. Arshad Ashak Atar, Vishal Abasaheb Misal, Umesh Dattatray Hajare, “Automation -Design of Automatic Bottle
Packing Machine”, International Journal on Theoretical and Applied Research in Mechanical Engineering
(IJTARME), ISSN: 2319 – 3182, Volume-2, Issue-2, 2013
[3]. J. Swider, G. Wszolek, W. Carvalho “Programmable controller designed for electropneumatic systems” 13th
International Scientific Conference on Achievements in Mechanical and Materials Engineering, 16th
-19th
May
2005, Gliwice-Wisla, Poland.
[4]. Arif Ozkan, Kerim Cetinkaya “Process Automation and Mixture Filling System Design”, Journal of Engineering
Research and Applied Science, pp 98-106, Volume 1(2), Dec. 2012.
[5]. Uttekar, K.; Gosavi, R.; Lad, S.; Kamat, J., "Implementation of sensor network for automation of bottle-capping
assembly station Using IEEE 802.15.4," 2nd International Conference on Instrumentation Control and Automation
(ICA), 15-17 Nov. 2011.
[6]. Chengwen Chai, JifieCai, Yiming Wang and Shuqin Wu “Research on PLC-Based Pneumatic Controlling System
of Flying Splicer of Web-Fed Offset Presses”. The open Mechanical Engineering Journal, Volume 5, 2011.

[7]. ZelikoSitum, TihomirZilic and Mario Essert “High Speed Solenoid Valves in Pneumatic Servo Applications” 15th
Mediterranean Conference on Control and Automation, July 27th
-29th
2007, Athens- Greece.
[8]. Mallaradhyah M, K.R. Prakash “Automatic Liquid Filling to Bottles of Different Height Using Programmable
Logic Controller.” International Journal of Mechanical and Production Engineering, ISSN: 2320-2092, Volume- 1,
Issue- 4, Oct-2013.
[9]. Savita, Lokeshwar “Implementation and Performance Analysis of Bottle Filling Plant Using Ladder Language.”
(IJSR) ISSN (Online): 2319-7064 Impact Factor: 3.358 Paper ID: 0201516 (2012).
[10]. Nabil Shaukat, “APLC Based Automatic Liquid Filling Process”, IEEE, publication page No. 226-233, 2002.

Simulation for Automation of Manufacturing, Filling And Capping The Bottles

More Related Content

What's hot (20)

Similar to Simulation for Automation of Manufacturing, Filling And Capping The Bottles (20)

More from IJMERJOURNAL (20)

Recently uploaded (20)

Simulation for Automation of Manufacturing, Filling And Capping The Bottles