Simulation of incremental conductance mppt with

IJRET: International Journal of Research in Engineering and Technology eISSN: 2319-1163 | pISSN: 2321-7308
__________________________________________________________________________________________
Volume: 02 Issue: 09 | Sep-2013, Available @ http://www.ijret.org 557
SIMULATION OF INCREMENTAL CONDUCTANCE MPPT WITH
DIRECT CONTROL METHOD USING CUK CONVERTER
Amarnath Kurella1
, R Suresh2
Abstract
PV Module Maximum Power Point Tracker (MPPT) is a photovoltaic system that uses the photovoltaic array as a source of electrical
power supply. Every photovoltaic (PV) array has an optimum operating point, called the maximum power point, which varies
depending on cell temperature, the insulation level and array voltage. The function of MPPT is needed to operate the PV array at its
maximum power point. The design of a Maximum Peak Power Tracking (MPPT) is proposed utilizing a cuk converter topology. Solar
panel voltage and current are continuously monitored by a MPPT, and the duty cycle of the cuk converter continuously adjusted to
extract maximum power. The design consists of a PV array, DC-DC cuk converter and many such algorithms have been proposed.
However, one particular algorithm, the Incremental Conductance method, claimed by many in the literature to be inferior to others,
continues to be by far the most widely used method in commercial PV MPPT’s. The general model was implemented on Mat lab, and
accepts irradiance and temperature as variable parameters and outputs the I-V characteristic and P-V characteristic
Index Terms: PV system; Maximum power point tracking (MPPT); Incremental conductance (Inccond); digital signal
processor (dsp)
-------------------------------------------------------------------------***------------------------------------------------------------------------
1. INTRODUCTION
Unfortunately, PV generation systems have two major
problems: the conversion efficiency of electric power
generation is very low (9-16%), especially under low
irradiation conditions and the amount of electric power
generated by solar arrays changes continuously with weather
conditions. Moreover, the solar cell V-I characteristic is
nonlinear and changes with irradiation and temperature. In
general, there is a point on the V-I or V-P curve only, called
the Maximum Power Point (MPP), at which the entire PV
system operates with maximum efficiency and produces its
maximum output power [5].The location of the MPP is not
known, but can be located, either through calculation models
or by search algorithms. Maximum Power Point Tracking
(MPPT) techniques [6] are used to maintain the PV array's
operating point at its MPP. MPPT is not a mechanical tracking
system that “physically moves” the modules to make them
point more directly at the sun. MPPT is a fully electronic
system that varies the electrical operating point of the modules
so that the modules are able to deliver maximum available
power.
As the MPP is always requested, and this point can be found in
any position on I-V curve, depending on temperature and
irradiation levels, the natural DC-DC converters [25] to be
applied as MPP Trackers are Buck, Boost, Buck-Boost, and
Cuk converter.
Safari A., Mekhilef S[1] presented a paper about that The
basic structural unit of a solar module is the PV cells and PV
module characteristics are comprehensively discussed, which
indicates an exponential and non-linear relation between
output current and voltage of PV module. It gives an idea
about the significant points on each I-V curve: open circuit
voltage, short circuit current and the operating point where the
module performs the maximum power (MPP).
ROBERTO FARANDA, SONIA LEVA [6] discussed Many
MPPT techniques under the energy production point of view:
Constant Voltage Method, Short-Current Pulse Method, Open
Voltage Method, Perturb and Observe Method, Incremental
Conductance Method and Temperature Method .These
techniques vary between them in many aspects, including
simplicity, convergence speed, hardware implementation,
sensors required, cost, range of effectiveness and need for
parameterization.
N.Femia, G.Petrone, G.Spagnuolo, M.Vitelli [10] discussed
how the Maximum power point tracking (MPPT) techniques
are used in photovoltaic (PV) systems to maximize the PV
array output power by tracking continuously the maximum
power point (MPP) which depends on panels temperature and
on irradiance conditions. The issue of MPPT has been
addressed in different ways in the paper.
E. Durán, M. Sidrach-de-Cardona, J. Galán, and J.M. Andújar
[25] are discussed several topologies of DC-DC converters for

__________________________________________________________________________________________
measuring the characteristic curves of photovoltaic (PV)
modules is theoretically analyzed. Eight topologies of DC-DC
converters with step-down/step-up conversion relation Buck-
Boost single inductor, CSC (Canonical Switching Cell), Cuk,
SEPIC (Single-Ended Primary Inductance Converter), Zeta,
Fly back, Boost-Buck-Cascaded, and Buck-Boost-Cascaded
converters) are compared and evaluated
2. WORKING
Working of a PV cell is based on the basic principle of
photoelectric effect. Photoelectric effect can be defined as a
phenomenon in which an electron gets ejected from the
conduction band as a consequence of the absorption of
sunlight of a certain wavelength by the matter (metallic or non-
metallic solids, liquids or gases).So, in a photovoltaic cell,
when sunlight strikes its surface, some portion of the solar
energy is absorbed in the semiconductor material. If absorbed
energy is greater than the band gap energy of the
semiconductor, the electron from valence band jumps to the
conduction band. By this, pairs of hole-electrons are created in
the illuminated region of the semiconductor.
The electrons thus created in the conduction band are now free
to move. These free electrons are forced to move in a
particular direction by the action of electric field present in the
PV cells. These flowing electrons constitutes current and can
be drawn for external use by connecting a metal plate on top
and bottom of PV cell. This current and the voltage (created
because of its built-in electric fields) produces required power.
A maximum power point tracker (MPPT) is a high efficiency
DC to DC converter which functions as an optimal electrical
load for a photovoltaic (PV) cell, most commonly for a solar
panel or array, and converts the power to a voltage or current
level which is more suitable to whatever load the system is
designed to drive.
PV cells have a single operating point where the values of the
current (I) and Voltage (V) of the cell result in a maximum
power output. Maximum power point trackers utilize some
type of control circuit or logic and algorithm to search for this
point and thus to allow the converter circuit to extract the
maximum power available from a cell. In short, photovoltaic
(PV) arrays are used to provide energy and MPPT are used to
correct the variations in the current-voltage characteristics of
the solar cells. The point on the current-voltage (I-V) curve of
a solar module under illumination, where the product of
current and voltage is maximum (Pmax, measured in watts).
The points on the I and V scales which describe this curve
point are named Imp (current at maximum power) and Vmp
(voltage at maximum power.). For the array to be able to
delivered the maximum possible amount of power, either the
operating voltage or current needs to be carefully controlled
Fig. 1 is illustrating the block diagram of MPPT system with
direct control using cuk converter. In this chapter explain the
mathematical model of PV system with comparative study of
MPPT methods.
Fig.1 Direct control method used in MPPT
2.1 PV Cell
Fig.2 shows the equivalent circuit of the ideal photovoltaic
module. The basic equation for output current of module[1] is
1
I PV
I d
V
IR s
R p
Fig.2 Single-diode model of the theoretical photovoltaic cell
and equivalent circuit of a practical photovoltaic device
including the series and parallel resistances
Where I is the PV array output current, V is the PV output
voltage, is the cell photocurrent that is proportional to
solar irradiation, represents the number of PV cells
Connected in series and represents the number of such
strings connected in parallel.
2

__________________________________________________________________________________________
is the cell short-circuit current at reference temperature
and radiation,
is short circuit current temperature coefficient,
T is the Nominal Temperature i.e 295.15K (25C)
is the cell reference temperature,
S is solar irradiation in
is the cell reverse saturation current that mainly depends
on the temperature, K is a constant.
3
is the reverse saturation at
is the band-gap energy of the semiconductor used in the
cell.
A is the area of photovoltaic cell.
k is Bolttzmann constant i.e. 1.3806503*10-23jouls/kelvin
q is electron charge i.e. 1.607*10-19c
These techniques vary in many aspects as: simplicity,
convergence speed, digital or analogical implementation,
sensors required, cost, range of effectiveness, and in other
aspects [6] [7].
2.2 Characteristics of Pv Cell
The performance characteristics of a photovoltaic module
depend on its basic materials, Manufacturing technology and
operating conditions.
Three points in these curves are of particular interest:
1. Short circuit point, where the voltage over the module is
zero and the current is at its Maximum (short circuit current
Isc).
2. Maximum power point or MPP, where the product of
current and voltage has its maximum (defined by Impp.Vmpp).
3. Open circuit point, where the current is zero and the voltage
has its maximum (open circuit voltage Voc).
Fig.3 PVA Characteristics V (X axis) Vs I (Y axis)
The measurements taken for obtaining an I-V curve is done by
controlling the load current. At open circuit, when no load
current is generated, a first characteristic value can be
measured: the open circuit voltage Voc. Increasing the load
fed by the photovoltaic module leads to a decreasing voltage V
with an increasing current I. In other words, by increasing the
load current from zero to its maximum value, the operating
point moves from the open circuit voltage at zero current to
the short circuit current Isc at zero voltage. The series of all
measured pairs (V, I) yields the characteristic I-V curve of the
module. From the characteristic curve of the module, it is clear
that the open circuit voltage of the photovoltaic module, the
point of intersection of the curve with the horizontal axis,
varies little with solar radiation changes. It is inversely
proportional to temperature, i.e., a rise in temperature
produces a decrease in voltage. Short circuit current, the point
of intersection of the curve with the vertical axis, is directly
proportional to solar radiation and is relatively steady with
temperature variations. Actually, the photovoltaic module acts
like a constant current source for most parts of its I-V curve
[3]
As demonstrated in Fig.4, Fig.5, an increase in solar radiation
causes the output current to increase and the horizontal part of
the curve moves upward. An increase in cell temperature
causes the voltage to move leftward, while decreasing
temperature produces the opposite effect. Thus, the I-V curves
display how a photovoltaic module responds to all possible
loads under different solar radiation and cell temperature
conditions.

__________________________________________________________________________________________
Fig.4 Voltage Vs Current characteristics of PVA with
Variation of Insulation
Fig.5 Characteristics of PVA incorporating effect of
Temperature
Photovoltaic modules have a very low conversion efficiency of
around 15% for the manufactured ones. Besides, due to the
temperature, radiation and load variations, this efficiency can
be highly reduced. In fact, the efficiency of any semiconductor
device drops steeply with the temperature. In order to ensure
that the photovoltaic modules always act supplying the
maximum power as possible and dictated by ambient operating
conditions, a specific circuit known as Maximum Power Point
Tracker (MPPT) is employed.
In most common applications, the MPPT is a DC-DC
converter controlled through a strategy that allows imposing
the photovoltaic module operation point on the Maximum
Power Point (MPP) or close to it. On the literature, many
studies describing techniques to improve MPP algorithms were
published [9] [10], permitting more velocity and precision of
tracking. On the other hand, there is no a theory to guide the
designer to choose, among the DC-DC converters family, the
best one to operate as MPPT, thus, in most cases, the designers
are tempted to use the simplest DC-DC converters[25]
2.3 Perturb and Observe MPPT Method
Fig.7 Flowchart of Perturb and Observe (P&O) methods
The Perturb and Observe algorithm[6-8] operate by
periodically perturbing(i.e. incrementing or decrem enting)the
array terminal voltage or current and comparing the PV output
power with that of the previous perturbation cycle. If the PV
array operating voltage changes and power increases, the
control system moves the PV array operating point in that
direction; otherwise the operating point is moved in the
opposite direction. In the next perturbation cycle the algorithm
continues in the same way.The flow chart of the Perurb and
Observe algorithm shown in Fig.7.
2.4 Incremental Conductance Algorithm
The purpose of the The Incremental Conductance method[6-
10] offers good performance under rapidly changing

__________________________________________________________________________________________
atmospheric conditions. Fig.8 shows that the slope of the PV
array power curve is zero at the MPP, increasing on the left of
the MPP and decreasing on the right hand side of MPP.The
basic equations of this method are as follows[1]
AtMPP 4
LeftofMPP 5
Right of MPP 6
Where I and V are PV array output current and voltage
respectively The left hand side of equations represents
Incremental conductance of PV module and the right hand side
represents the instantaneous conductance. From (2), (3) and
(4) it is obvious that when the ratio of change in the output
conductance is equal to the negative output conductance, solar
array will operate at the maximum power point.
Fig.8 Basic idea of incremental conductance method on a P-V
curve of a solar module
In other words, by comparing the conductance at each
sampling time, the MPPT will track the maximum power of
the PV module[12] [13]. The flow chart of Incremental
Conductance method shown in Fig.9.It makes use of
instantaneous and incremental conductance to generate an
error signal which is zero at MPP; however it is not zero at
most of the operating points, but it make the error from the
MPPs near to zero [3]
Fig.9 Flowchart of Incremental conductance method
2.5 Comparison
A common problem in Pertub and Observe algorithm[9] is that
the array terminal voltage is perturbed every MPPT cycle;
therefore when the MPP is reached, the output power oscillates
around the maximum, resulting in power loss in the PV
system. This is especially true in constant or slowly-varying

__________________________________________________________________________________________
atmospheric conditions. Furthermore, Perturb and Observe
method can fail under rapidly changing atmospheric
conditions.
Incremental conductance method [5-8] is more efficient than
Perturb Observe method [5-7] because panel terminal voltage
is changed according to its value relative to the maximum
power point voltage. Therefore, this method is independent on
solar panel characteristics.
Table .1 Overall MPP Tracking Efficiencies
Incremental conductance method eliminates the problem that
is seen in Perturb and Observe method. Therefore, oscillations
that cause power loss are not occurred in Incremental
conductance method. A summary of the MPPT efficiencies of
two algorithms are shown in Table 1, Table. 2.
To complete our analysis a simple discussion about the cost of
the MPPT technique is presented [2] [3]. A satisfactory MPPT
costs comparison can be carried out by knowing the technique
(analogical or digital) adopted in the control device, the
number of sensors, and the use of additional power
component, considering the other costs (power components,
electronic components, boards, etc…) equal for all the devices.
To make all the cost comparable between them, the
computation cost comparison is formulated taking into account
the present spread of MPPT methods. The number of sensors
required to implement the MPPT technique also affects the
final costs. Most of the time, it is easier and more reliable to
measure voltage than current and the current sensors are
usually more expensive and bulky. The irradiance or
temperature sensors are very expensive and uneconomic.
Table 2: Comparison of MPPT methods
Specifications Perturb and
Observe
Incremental
Conductance
Efficiency Medium
About 95%
depending on how
method is
optimized
High About 98%
depending on how
method is
optimized
Complexity Difficult
Realization Easy to implement
as few measured
parameters
More complex
hence Micro
controller/DSP
needed
Cost Relatively lower Involves higher
cost
Reliability Not very accurate
and difficult to
whether operating
at MPPT or not
Accurate and
operates at MPPT
but response time
dependent
Rapid changing
atmospheric
conditions(varying
radiation and
temp)
Unpredictable
performance with
oscillations around
MPP, slower
response
Good and
automatically
adjust module
operating voltage
with no
oscillations
Other Limitations Difficult to locate
MPP
Voltage and
current sensors are
need usually high
expensive
3. CONVERTER CONFIGURATIONAND
SELECTION
Solar cells are the fundamental power conversion unit of a
photovoltaic (PV) system. The basic operation of a solar cell is
characterized by its I-V curve. Only the experimental
measurement of the I-V curve allows us to know with
precision the electrical parameters of a PV cell, module or
array. This measure provides important information for the
design, installation and maintenance of photovoltaic systems.
The experimental measure of the I-V characteristic curve can
be performed using step-up/step-down DC-DC converters in
Continuous Conduction Mode (CCM) [1]. The switching
power of DC-DC converters are widely used in photovoltaic
systems to transform DC power from a voltage level to
another, and for tracking the maximum power point
(MPPT).In this chapter, a survey of step-down/step-up DC-DC
converters and their application to obtain I-V characteristic
curves of PV modules is presented
Sky
conditions
Perturb and observe Incremental
conductance
Days
of data
MPPTeffi
ciency
Days of
data
MPPT
efficienc
y
clear 20 98.7 17 98.7
Partly
cloudy
14 96.5 11 97
cloudy 9 98.1 11 96.7
Over all 43 97.8 39 97.4
Simulate
over all 99.3
99.4

__________________________________________________________________________________________
3.1 Choice of Converter for MPPT
VS
I S IL
VL
Fig.10 Converter acting as a Maximum Power Point Tracker
When proposing a maximum power point tracker, the major
job is to choose and design a high efficient converter which is
supposed to operate as the main part of the MPPT. The
choosing of DC-DC converter based on the desired output
voltage from the MPPT in term to ensure the PV module will
operate at the maximum point.
3.2 CUK CONVERTER
The load voltage of converter can be obtained in terms of load
current by the relation
7
Where Vload is the load voltage, Iload is the load current and
Rload is the load resistance. We shall assume the operation of a
cuk converter
8
The average input power to the DC-DC converter equals the
average output power thereby, we get a relation
9
Combining the above two equations, we write
10
D here represents the voltage conversion ratio of the cuk
converter. So, when seen from the source side, the effective
resistance will be . This is a function of D,
which we can control to fix the operating point near the MPP.
We have to note that the range of D is zero to one. The MPP
can be found in any position on I-V curve, depending on
temperature and radiation levels, the natural DC-DC
converters to be applied as MPP Trackers are Buck-Boost,
Cuk, because they have no non-operational region. TABLE.3
summarizes the equations for DC-DC Buck, Boost, Cuk,
converters. Comparative study on different schemes of
switching converters is presented in the chapter.
DC-DC
converter
Range
Cuk
converter
Buck
converter
Boost
converter
The need of converter in the MPPT system is to maximize the
varied input of DC voltage. In term of maximized the output
voltage by step up or step down the input voltage the cuk
converter is ideally to be choose in the MPPT design
compared to the Buck converter, Boost converter because cuk
converter has low switching losses and highest efficiency
among non-isolated DC-DC converters [26-30]. It also can
provide a better input and output current characteristic due to
the inductor on the both input and output stage. The maximum
power point of 12V commercial PV module is above or below
that voltage for most combinations of insolation and
temperature. So buck and boost converter can operate at the
MPP undermost step up and step down the voltage but not at
all condition. While for the cuk converter output voltage must
be above or below the input voltage so that’s why, cuk
converter will always be able to operate at the panel’s MPP. In
term of simplicity a buck converter with a MOSFET switch
still requires an additional diode or MOSFET’s to block the
reverse current flow when the panel voltage drops below the
battery voltage, as an advantages of cuk converter naturally it
has this devices as part of its structure, which eliminates an
additional source of voltage drop and power loss. A boost
converter has been employed in this application to regulate the
power output to the load. It consists of an inductor, a logic
level, Power MOSFET switch, a ordinary diode and
capacitors. Fig. 11 shows a typical connection of a cuk
converter. The basic converter containing at least two
semiconductors switches (a diode and a transistor). Filters
made of capacitors (sometimes in combination with inductors)

__________________________________________________________________________________________
are normally added to the output of the converter to reduce
output voltage ripple.
3.3 Operation of Cuk Converter
Figs.12a and 12b depicts cuk converter and its operating
modes which used as the power stage interface between PV
module and the load. Cuk converter has two modes of
operation. First mode of operation is when the switch is closed
(ON) and it is conducting as a short circuit. In this mode,
capacitor releases energy to the output. The equations for the
switch conduction mode are as follows
Vd
L 1 L2
C1
C 2
V o RL
VL1 VL2VC1
iL1 iL2
io
Fig.11 Cuk converter
Fig.12 Cuk converter with (a) switch ON and (b) switch OFF
11
12
13
14
On the second operating mode when the switch is open (OFF),
diode is forward biased and conducting energy to the output.
Capacitor C1 is charging from input. Equations for this mode
of operation are:
15
16
17
18
The principles of cuk converter operating conditions state that
the average values of the periodic inductor voltage and
capacitor current waveforms are zero, when the converter
operates in steady state. Some analysis of cuk converter
specifications is provided in [25]. The power circuit of the
proposed system consists of a Cuk converter and gate drive,
the control of the switching is done using the control circuit.
The control tasks involve measuring analog voltage and
current of the PV module using current and voltage sensors,
convert them to digital using ADC, process the obtained
information in a microcontroller and then compare to the
predefined values to determine the next step, revert the PWM
to the gate drive and hence control the switching of IGBTs.
The control loop frequently happens with respect to the
sampling time and the main program continues to track the
MPPs.
The cuk converters provide the opportunity to have either
higher or lower output voltage compare with input voltage.
Although buck and boost configuration is cheaper than cuk,
some disadvantages such as discontinuous input current, high
peak currents in power components and poor transient
response makes it less efficient. On the other hand, cuk
converter has low switching losses and highest efficiency
among non-isolated DC-DC converters [26]. It also can
provide a better input and output current characteristic due to
the inductor on the both input and output stage.
4. SIMULATION RESULTS
Fig.13 Simulink model of Incremental Conductance MPPT

__________________________________________________________________________________________
Fig.14 Change in Duty ratio with irradiation
Fig.15 PV output power changing with Irradiation
Fig.16 changing irradiation with Time (sec)
Fig. 17 PV module output Power changing with Temperature
Fig. 18 PV module output Voltage
Fig. 19 Change in Duty ratio with Temperature
CONCLUSIONS
From the observations made above, we conclude that the
system developed is capable of extracting maximum power
from the photovoltaic module at the same time providing a
regulated DC supply. The proposed PV system and MPPT was
simulated. The Incremental Conductance method is more
efficient compare to all MPPT methods because panel terminal
voltage is changed according to its value relative to the MPP
voltage. The Incremental Conductance method is more
efficient than Perturb and Observe method because panel
terminal voltage is changed according to its value relative to
the MPP voltage. The Incremental Conductance method offers
good performance under rapidly changing atmospheric
conditions. On the other hand; cuk converter has low switching
losses and highest efficiency among non-isolated DC-DC
converters. It also provides a better input and output current
characteristic due to the inductor on both input and output
stage. Thus cuk converter configuration is a proper choice to
be employed in designing the MPPT.

__________________________________________________________________________________________
REFERENCES
[1] Safari A, Mekhilef S, “Simulation and Hardware
Implementation of Incremental Conductance MPPT with
Direct Control Method Using Cuk Converter”, IEEE Trans,
March 2010.
[2] Abou El-Maaty Metwally Metwally Aly Abd El-Aal,
“Modeling and Simulation of a Photovoltaic Fuel Cell Hybrid
System”, Dissertation for Dr.-Ing, University of
Kassel,Germany, 15 April 2005.
[3] H.S.Rauschenbach. “Solar cell array design handbook",
Van Nostrand Reinhold, 1980.
[4] H. J. M¨oller, “Semiconductors for Solar Cells”. Norwood,
MA: Artech House, 1993.
[5] V. Salas, E. Olias, A. Barrado, and A. Lazaro, “Review of
the maximum power point tracking algorithms for stand-alone
photovoltaic systems”, Sol. Energy Mater. Sol. Cells, vol. 90,
no. 11, pp. 1555–1578, Jul. 2006.
[7] L. Pang, H. Wang, Y. Li, J. Wang, and Z. Wang,
“Analysis of Photovoltaic Charging System Based on MPPT”,
Proceedings of Pacific-Asia Workshop on Computational
Intelligence and Industrial Application 2008 (PACIIA ‘08),
Dec 2008, pp. 498-501.
[8] K.S.R. Rajeswararao, S. UmaShankar, N. Sudhakar,
D.Vijaya Kumar, ”Performance of a Controlled Capacitor
Charging type converter Based on Switch Utilization Ratio”,
International conference on Advances in Renewable
Energy(ICARE 2010), Maulana Azad National Institute of
Technology, Bhopal,June 24-26, 2010.
[9] A. S. Sedra and K. C. Smith, Microelectronic Circuits.
London, U.K.: Oxford Univ. Press, 2006.
[10] Trishan Esram, Patrick L. Chapman, “Comparison of
Photovoltaic Array Maximum Power Point Tracking
Techniques”, IEEE Trans. on Energy Conversion, vol. 22,no.
2, pp.439-449, June 2007
[11] H.S.Rauschenbach. “Solar cell array design handbook",
Van Nostrand Reinhold, 1980.
[12] Trishan Esram, Patrick L. Chapman, “Comparison of
Photovoltaic Array Maximum Power Point Tracking
Techniques”, IEEE Trans. on Energy Conversion, vol. 22,no.
2, pp.439-449, June 2007.
[13] Zhou Yan, Liu Fei, Yin Jinjun, Duan Shanxu, “Study on
realizing MPPT by improved incremental conductance method
with variable step-size”, ICIEA, IEEE Conference on
Industrial Electronics and applications, pp. 547~550, June
2008.
[14 N.Femia, D.Granozio, G.Petrone, G.Spaguuolo, M.Vitelli,
“Optimized One-Cycle Control in Photovoltaic Grid
Connected Applications”, IEEE Trans. Aerosp. Electron.Syst,
vol. 2, no 3, July 2006.
[15] W. Wu, N. Pongratananukul, W. Qiu, K. Rustom, T.
Kasparis and I. Batarseh, “DSP-based Multiple Peack Power
Tracking for Expandable Power System”, Proc. APEC, 2003,
pp. 525-530.
[16] C. Hua and C. Shen, “Comparative Study of Peak Power
Tracking Techniques for Solar Storage System”, Proc. APEC,
1998, pp. 679-685.
[17] D.P.Hohm and M.E.Ropp, “Comparative Study of
Maximum Power Point Tracking Algorithms Using an
Experimental, Programmable, Maximum Power Point
Tracking”, Test Bed, Proc. Photovoltaic Specialist
Conference, 2000, pp. 1699-1702.
[18] K.H.Hussein, I.Muta, T.Hoshino and M.osakada
“Maximum Power Point Tracking: an Algorithm for Rapidly
Chancing Atmospheric Conditions”, IEE Proc.-Gener. Transm.
Distrib., vol. 142, no.1, pp. 59-64, January, 1995.
[19] K.K. Tse, B.M.T. Ho, H.S.-H. Chung, S.Y.R. Hui, “A
comparative study of maximum-power-point trackers for
photovoltaic panels using switching-frequency modulation
scheme”, IEEE Trans. on Industrial Electronics, vol. 51, no.2,
pp. 410- 418, April 2004.
[20] R. Faranda S. Leva and V. Maugeri “MPPT techniques
for PV Systems: energetic and cost omparison”,IEEE lectrical
Engineering Department of Politecnico di Milano, Piazza
Leonardo da Vinci 32, 20133, Milano, Italy.2008.
[21] Anuradha Kar, Asim Kar “A New Maximum Power Point
Tracking Algorithm for PV Modules under Partial Shading
and Rapidly Varying Illumination”, IEEE Trans, University of
Calcutta, Kolkata, India, 2009.
[22] Joanne Hui, Alireza Bakhshai, and Praveen K. Jain “A
Hybrid Wind-Solar Energy System: A New Rectifier Stage
Topology”, IEEE Trans, Department of Electrical and
Computer Engineering Queen’s Center for Energy and Power
Electronics Research (ePOWER), Queen’s University,2010.
[23] J. Lu, S. Stegen, and D. Butler “High Frequency and High
Power Density Transformers for DC/DC Converter used in
Solar PV System” IEEE School of Engineering, Griffith
University, Nathan, Brisbane, Qld 4111, Australia Surtek Pty
Ltd, Acacia Ridge, Brisbane, Qld 4110, Australia,2008.
BIOGRAPHIES:
AMARNATH KURELLA: II-M.tech at Sri
Venkateshwara Engineering College
,Suryapet his interested in Power
Electronics,Power systems and non
conventional energy sysems
R SURESH: Working as a Assistant
Professor at Sri Venkateshwara Engineering
College ,Suryapet his interested in Power
Electronics, Power Systems and non
conventional energy sysems

Simulation of incremental conductance mppt with

More Related Content

What's hot (20)

Viewers also liked (20)

Similar to Simulation of incremental conductance mppt with (20)

More from eSAT Publishing House (20)

Recently uploaded (20)

Simulation of incremental conductance mppt with