SOP ENGINEERING

PROPERTY OPERATIONS POLICIES AND PROCEDURES The Chief Engineer will prepare the Engineering Department Fiscal Budget. The monthly budget is to be forecasted and variances explained where required. The Chief Engineer will maintain an expense tracking system in order to control the monthly budget. Monthly utility accruals are to be developed by the Chief Engineer. All expenses will be coded to the appropriate Engineering account number by the Chief Engineer. Any expenses will be charged to the Engineering budget must be approved by the Chief Engineering. 1. 2. 3. 4. 5. 6. STANDARDS: The Annual Energy and Repair and Maintenance Fiscal Budgets are to be developed by the Chief Engineers. The following information is to be obtained: Marketing plan Energy and R&M Chart of Accounts Energy and R&M budget spread sheet forms Prior year and year-to-date actual budget history Projected occupancy and food covers Energy Consumption Report Anticipated utility rate increase Annual service contract expenses Projected cost of parts and materials needed to maintain in the property Anticipated cost of R&M projects Inhouse labour rates plus budgeted increases 1. 2. PROCEDURE: The Chief Engineer is to implement Budget Control guidelines in accordance with the following procedures as well as with any policies issued by the Accounting Department. POLICY: To establish budget preparation and control guidelines for Engineering Department expenditures PURPOSE:

No outside contractors, repairmen, service representatives or parts and materials are to be contracted and/or ordered by any department without prior knowledge and approval by the Chief Engineer. 10. Any expense charged to Engineering is to be reviewed and approved by the Chief Engineer prior to posting by the Controllers Department. 9. Note: The M-T-D General Ledger Distribution List can be used for specific verification information. The Chief Engineer is to code any expense charged to the Engineering Department by the appropriate account number, which is based on the Energy and R&M Chart of Account code numbers. 8. Note: Energy and R&M Chart of Account code numbers are to be obtained from the Controller’s Office. All monthly expenses are to be verified against the Financial Reporting System (FRS) which is to be submitted to the Chief Engineer for review. Errors noted are to be corrected by the Accounting Department the following month. 7. Utility accruals are to be developed monthly by the Chief Engineer. Accruals are determined by calculating the actual utility consumption to date and projecting the consumption for the remaining period. The present utility average rates are multiplied by the projected consumption to obtain the accrual amounts. 6. A monthly 30-60-90 day forecast is to be developed, explaining in detail any anticipated variance to the budgeted amounts. The forecast if to be submitted to the Accounting Department . 5. The Chief Engineer is to develop a work-able control mechanism whereby potential red flag budget items are identified as they occur and are to be communicated to the General Manager and Controller on a weekly basis. (See Figure I as an example of a tracking format. This can be used, or a detailed breakdown of each account can be set-up). 4. The projected budget expense for each account is to be spread throughout the twelve month period, using the data above, and then submitted to Accounting Department for the General Manager’s approval. 3.

A parts and supplies inventory is to be conducted regularly, to ensure availability when needed. 6. Shelving or bins should be used for parts and supplies within the storage area (s) to provide uniformity and organization. All bins/shelving will be labeled with appropriate identification. The area (s) must be orderly at all times. 2. Access to spare parts and supplies must be restricted to the Engineering Department employees only and these areas are to be locked at all times. 3. A minimum stock or critical parts and supplies that must be on hand for daily operation should be established. Availability and vendor delivery times will be the determining factors in establishing minimum par stocks. Excess inventories are to be avoided whenever possible. 4. Written inventories are to be maintained to identify vendors, pricing, parts numbers, descriptions and maximum and minimum quantities, etc. 5. A minimum par stock of critical parts and supplies will be established and maintained. 2. It is the responsibility of the Chief Engineer, or his designee, to control, and issue inventory 3. No spare parts or supplies are to be removed from the property. 4. A secure storage area must be provided in the maintenance shop for spare parts and supplies. A secure area consists of a lockable room, cage or storage cabinet. 1. PROCEDURES All Engineering Department employees will be held responsible for maintaining adequate inventories by informing the Chief Engineer or his designee when parts/supplies are getting low. 7. All parts and supplies will be stored in secure areas. 1. STANDARDS: The Chief Engineer will ensure that Department parts and supplies are purchased and controlled. POLICY: To control the Engineering Department inventories and ensure availability of critical parts and supplies. PURPOSE: PROPERTY OPERATIONS POLICIES AND PROCEDURES

If the department has a personal computer or access, to one, it is recommended that the parts inventory be computerized. 11. When selecting vendors, delivery by the vendor is to be considered so as to minimize sending personnel off-property. 10. Parts and supplies are to be purchased through vendors with whom Starwood Hotels & Resorts has purchasing agreements where applicable. 9. Spare parts and/or supplies are the property of the hotel and are never to be removed from the property. 8.

PROPERTY OPERATIONS POLICIES AND PROCEDURES The department head is responsible for completing the top portion of the R & M Project Request Form; providing as much detail as possible. Purpose and justification for the project request must be stated clearly and the estimated cost determined. 2. The department head must obtain appropriate Executive Committee member approval for the concept. 3. The Executive Committee member must then obtain the General Manager’s signature for concept approval. 4. Upon approval of the concept, the Chief Engineer is to determine material, labour and (if necessary) contractor costs. The Chief Engineer then reviews the project with the department head for accuracy and additional information, if required. 5. When the cost has been determined, the Accounting Department is to designate the appropriate account funding and the R & M Project Request is to be signed by the Hotel Controller. 6. Upon completion of the above steps, final approval of the request is to be obtained from the General Manager. 7. The approved project is then scheduled for completion by the Chief Engineer. 8. An R & M Project Request Form, as in Figure 1 , is to be completed when any department requests maintenance services for work which is not repair and maintenance of the existing facility. 1. PROCEDURE: The Controllers Department will designate R & M project account funding . 2. Any project that is expensed to R & M must be initiated through the R & M Project Request procedure. 1. STANDARDS: The General Manager must approve any R & M project request. 3. The Chief Engineer is to implement Budget Control guidelines in accordance with the following procedures as well as with any policies issued by the Accounting Department. POLICY: To provide a system of controlling Property Operations expenses not directly related to repairs and maintenance. PURPOSE:

GENERAL MANAGER DATE: ________________________ APPROVED BY__________________________________________________ DATE:______________________________________ CONTROLLER APPROVAL TO BE COMPLETED BY EXECUTIVE OFFICE TOTAL COST ______________________________________________________________________________________________________ TO BE COMPLETED BY HOTEL CONTROLLER TO BE FUNDED FROM LABOUR COST PARTS & MATERIAL COST TO BE COMPLETED BY ENGINEERING DEPARTMENT DATE: GENERAL MANAGER CONCEPT APPROVAL OUTSIDE CONTRACT COST ESTIMATED HOURS PERMANENET OR TEMPORARY PROJECT: ESTIMATED COST: SPECIFIC AREA: RETURN TO CHIEF ENGINEER DATE: EXECUTIVE COMMITTEEE MEMBER APPROVAL: PROJECT DESCRIPTION: SIZE, SHAPE, TYPE OF FINISH, COLOUR QUANTITY, ETC… PROVIDE SKETCH OR ADDITIONAL INFORMATION ON BACK OF THIS FORM. PURPOSE OR FUNCTION OF PROJECT: DEPARTMENT DATE: FROM: TO BE COMPLETED BY REQUESTING DEPARTMENT Figure 1. – R & M PROJECT REQUEST Page 2 of 2 Number 1.3 ADMINISTRATION Section: R & M PROJECT REQUEST Subject:

The Chief Engineer will maintain the HLP file. 5. e. CHILLER – chiller consumption can reach very high levels in some areas and period. If submeters are installed on the chiller circuits enter kwH readings on a daily basis and the weekly total in the total/average column. a. KWH is the row where you log the daily electricity consumption. At the end of the week calculate the total for the week and enter in the total/average column. b. MAX.DEMAND is used if the power company charges for max demand. Enter the daily figures from the meters. In the total/average column enter the highest value reached during the week. c. POWER FACTOR (COS) can be a penalizing factor on the electricity bill. Calculate the power on a daily basis and enter the average for the week in the total average column. d. LOAD FACTOR shall be calculated on a daily basis. Enter the weekly average in the total/average column. The Chief Engineer is to complete and distribute the controller’s monthly summary (HLP.02). 2. The Chief Engineer is to complete and submit to Divisional/Regional Office the monthly summary (HLP.03). 3. The Chief Engineer is to complete yearly the ENERGY TARGET (HLP.04) and the justification of target (HLP.05). 4. The Chief Engineer is to complete the weekly utility log (form HLP.01) on a timely basis. All the data entered in the weekly utility log must originate from the shifts report. 1. PROCEDURES The Chief Engineer is to complete the weekly utility log (HLP.01). 1. STANDARDS: The Chief Engineer is responsible for monitoring the property’s energy consumption and maintain the HLP file up to date at all times. POLICY: To provide a comprehensive means to monitor and control each property utility consumption. PURPOSE: Section: ADMINISTRATION ENERGY CONSUMPTION ANALYSIS Subject: PROPERTY OPERATIONS POLICIES AND PROCEDURES

The Chief Engineer is to complete monthly the CONTROLLERS MONTHLY SUMMARY (HLP.02) no later than the Starwood Hotels & Resorts closing date. All costs in the report must be in local currencies. 2. s. CDD is the calculated cooling degree days calculated in degrees Celsius with a base of 18.3 o C. t. HDD is the calculated heating degree days calculated in degree Celsius with a base of 18.3 o C. p. DRY BULB MAX is used with the dry bulb min to calculate the degree days. q. AIR MEAN TEMPERATURE is the 24 hours daily average men temperature from the weather bureau used to calculate the degree days. r. OCCUPANCY . Enter daily the figure obtained from the Financial Controller. k. SEWAGE is used to record sewer flow in properties charged for effluent in cubic meter. l. COOLING TOWERS is used to monitor the make up water consumption and the operation of chemical dosing. m. SWIMMING POOL is used to monitor the overflow and evaporation of the pool in cubic meter. n. HOT WATER is used to monitor the hot water consumption in cubic meter. o. DRY BULB MIN is used in properties where it is impossible to obtain the 24 hours mean temperatures. j. CITYWATER is used for recording the total daily water consumption in cubic meter. u. REMARK S can be used to record miscellaneous information such as Starwood Hotels & Resorts closing dates, swimming pool refill after cleaning etc. f. OIL consumption in liters shall be entered daily. Use tank meters or supply lines meters. The weekly total is entered in the total/average column. g. STEAM is used for recording operating hours of steam boilers or meter readings from steam/hot water supply. h. KWH is used to record consumption of kitchen water heaters, i. DWH is used for recording the total daily water consumption in cubic meter.

5. EXCHANGE RATE is the monthly average exchange rate between the local currency and the US$. The figure can be obtained from the Financial Controller. 6. HOTEL AREA is the hotel area in square meters. However, areas which are not heated, ventilated or air-conditioned are not to be included. Parking garages which only have exhaust are not to be included. 7. FUEL OIL is the consumption and cost of fuel oil. The first two columns are the actual figures for the current month. Consumption is to be entered in GJ and cost in local currency. The next two columns are a running total covering consumption and cost from January to date. Column 5 and 6 are the target for the month entered in GJ and local currency. The last two columns are a running total covering the target and cost from January to date. 8. GAS is the consumption and cost of gas. Consumption of gas used only for heating purpose is to be entered. Consumption of gas used for cooking is not to be entered. The figures shall be entered as described in 7 FUEL OIL. 9. STEAM/HOT WATER is the consumption of steam or hot water if purchased. 4. DATE is the date when the report is completed, usually the closing date of the Starwood Hotels & Resorts month. The Chief Engineer is to complete and submit monthly to Divisional/Regional Office the MONTHLY SUMMARY (HLP.03) Great care should be taken to submit reports on time and with accurate figures. The reported figures will be input for the divisional/regional reports where the performance factor is calculated for each hotel. REGIONAL MONTHLY SUMMARY (HLP.03) is a report of monthly consumption and expenses to the divisional/regional Engineer. The contents of the various cells is described hereunder: 3. 1. HOTEL is the name of the property. 2. STARWOOD HOTELS & REOSRTS PERIOD is the name of the Starwood Hotels & Resorts month covered in the report. The Starwood Hotels & Resorts calendar can be obtained from the Financial Controller. 3. AVAILABLE ROOMS is the total number of room nights available in the property. The figure can be obtained from the Financial Controller.

20. REMARKS is a section to enter justifications or unusual events which could have affected the figures. 21. STAFF is the row to enter the total number of staff working in the HLP and R&M sections. 19. BUDGET R&M are the figures for the repair and maintenance costs. The figure shall be entered as in 18 BUDGET HLP. 22. CHIEF ENGINEER is the row to enter name and signature of the Chief Engineer in charge. The Chief Engineer is to complete yearly in December the ENERGY TARGET (HLP.04) for the coming year, 4. 15. COVERS is the row to enter the total number of covers served in the restaurant during the period. 16. LAUNDRY PIECES is the row to enter the total laundry pieces processed in the property during the period. These figures can be obtained from the Housekeeper or the Financial Controller. 17. WATER is the row for consumption and cost of water purchased by the property. The figures shall be entered as described in 7 FUEL OIL. 18. BUDGET HLP are the heat, light and power actual costs for the current month and year to date. The last two columns are the Budget or Target figures. You will receive monthly the P&L statement from the controller to verify your figures, The Chief Engineer is to complete yearly in December the JUSTIFICATION OF TARGET (HLP .05). This is to be submitted to the Divisional /Regional Office with the ENERGY TARGET to detail and justify energy conservation programs and describe the calculation behind the conservation program. 5. 14. OCCUPANY % is the hotel occupancy measured in percentage of available rooms for the period. These figures can be obtained from the WEEKLY UTILITY LOG (HLP.01) or from the Financial Controller. 10. ELECTRICITY is the consumption and the cost of electricity purchased by the property. 11. TOTAL is the total of all the above. 12. HDD is the row for heating degree days. The first two columns are for the month and year to date actual values. The last two columns are for the predicted monthly and year to date values. 13. CDD is the row for cooling degree days. The figures shall be entered as in HDD.

01-Weekly Utility Log (HLP.01) 02- Controllers Monthly Summary (HLP.02) 03- SMC Monthly Summary (HLP.03)] 04- Energy Target (HLP.04) 05- Justification of Target (HLP.05) 06- General Site Data (HLP.06) 07- Electrical Summary (From SMC) 08- Fuel Oil Summary (From SMC) 09- Gas Summary (From SMC) 10- Steam Summary (From SMC) 11- Total Energy Summary (From SMC) 12- HLP Budget 13- Energy Bills 14- Water Bills 15- Energy Contracts 16- Best Fit Line 17- Weather Data The Chief Engineer will maintain an updated file which is comprised of the following subdivisions: 6. These hotels with personal computer will use the software developed by the Divisional Office for report preparation. 7. Section: Number: 1.4 Page 5 of 10 ADMINISTRATION ENERGY CONSUMPTION ANALYSIS Subject:

Chiller (Kwh) Load Factor KWH Steam (kgs) DWH (m3) Oil (liters) Power Factor Max Demand Kwh Total avr. Total/avr Sun Sat Fri Thu Wed Tue Mon Day Prev. year This week Date Week No. YEAR WEEKLY UTILITY LOG HLP-01 Page 6 of 10 Section Number: 1.4 ADMINISTRATION Subject: ENERGY CONSUMPTION ANALYSIS

Remarks CDD ( o C) HDD ( o C) Hot Water (m3) Swimming Pool (m3) Avr Mean Temp ( o C) Occupancy Covers Dry Bulb Max ( o C) Dry Bulb Min ( o C) Cooling Tower (m3) Sewage (m3) City Water (m3) Page 6 of 10 Section Number: 1.4 ADMINISTRATION Subject: ENERGY CONSUMPTION ANALYSIS

Remarkks Cost Consumption Cost Water Consumption cub m Cost Cost Consumtion Consumtion liters Fuel Oil Cost Consumption KWH Shop 3 Shop 2 Shop 1 Hotel Electricity Period CONTROLLERS MONTHLY SUMMARY HLP-02 Page 7 of 10 Section Number: 1.4 ADMINISTRATION Subject: ENERGY CONSUMPTION ANALYSIS Chief Engineer This report must be submitted to Controller not later than each Starwood Hotels & Resorts closing date

20 Remarks ______________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________ This report must be submitted to SMC no later than the first working day after each Starwood Hotels & Resort closing date TARGET ACTUAL 6 Hotel area sgr m 3 Available Rooms 5 Exchange Rate 2 ITT Period 4 Date 1 Hotel REGIONAL MONTHLY SUMMARY HLP-03 Page 8 of 10 Number: 1.4 Section ADMINISTRATION Subject: ENERGY CONSUMPTION ANALYSIS 19 Budget R&M 18 Budget HLP 17 Water cubic m 16 Laundry Pieces 15 Covers 14 Occupancy 13 CDD 12 HDD 11 Total GJ 10 Electricity GJ 9 Steam/Hot Water GJ 8 Gas GJ 7 Fuel Oil GJ Cost Unit Cost Unit Cost Unit Cost Unit R&M Chief Engineer HLP 21 Staff

NOTE: each month represent a Starwood Hotels & Resorts calendar month This report must be submitted together with target justification HLP-05 Page 9 of 10 Number: 1.4 Section ADMINISTRATION Subject: ENERGY CONSUMPTION ANALYSIS Target GJ Target GJ DECEMBER Target GJ SEPTEMBER Target GJ OCTOBER Target GJ NOVEMBER Total TOTAL Target GJ AUGUST Target GJ JULY Target GJ JUNE Target GJ MAY Target GJ APRIL Target GJ MARCH Target GJ FEBRUARY Target GJ JANUARY Cooling degree days Heating degree days Steam Gas Oil Electric TARGET Year Hotel ENERGY HLP-04 Date Chief Engineer

Which area have you considered for energy conservation ? __________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________ Why have you chosen these areas? ________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________ List here further details and calculations why you want to introduce above conservation program __________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________ _________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________ Use additional paper if necessary This report must be submitted together with energy target HLP-04 Page 10 of 10 Number: 1.4 Section ADMINISTRATION Subject: ENERGY CONSUMPTION ANALYSIS Year Hotel JUSTIFICATION OF TARGET HLP-05 Energy as% of total Area 3 Energy as % of total Area 2 Energy as % of total Area 1 Name the 3 areas which consume most energy in your hotel

Engineering Department labour associated with exhibit services will be recovered to budget. 5. Timely completion and submission of the form to the Engineering Department is necessary; 10 days prior is recommended. This will promote guest satisfaction by ensuring that the Department has adequate time to prepare for the function. 6. A competitive price review of local hotels is to be conducted at least annually, for services provided and the form updated accordingly. 2. Sales, Catering and Convention Services are to use this form exclusively and will review in detail the available services and associated costs with the client. They are to complete the form and distribute to Engineering, Accounting and the Customer. 3. In the event the exhibit costs are waived , the form must still be completed in order for the Engineering Department to provide the requested client services. 4. The waiving of any exhibit service charges, whether for business reasons or charitable events, must be approved by the General Manager, in addition to the Director of Sales and Marketing or the Director of Food and Beverage. A copy of the waiver approval is to be sent to the Controller's office and the Chief Engineer. 5. It is the responsibility of the sales, property and convention services to ensure the Exhibit Service form is completed and forwarded to the chief Engineer at the earliest possible time. 2. The Chief Engineer will schedule the exhibit service set-ups based on the completed Exhibit Service forms. 3. A 25 percent late charge will be assessed to those clients which request additional services at the last minute, except for banquets. 4. The Chief Engineer will develop an Exhibit Service Form tailored to the hotel’s specific needs. See Figure 1 for example form. 1. PROCEDURES An Exhibit Service form Is to be developed by the Chief Engineer. 1. STANDARDS: The Chief Engineer will implement and monitor the Exhibit Service procedure . POLICY: To provide special services and utility requirements for exhibitions, groups, meeting planners, vendors or individuals and ensure that charges for such are documented. PURPOSE: Section: ADMINISTRATION EXHIBIT SERVICE Subject: PROPERTY OPERATIONS POLICIES AND PROCEDURES

Labour associated with exhibit services, both straight and overtime rates, including benefits, are chargeable to the client. The actual payroll costs are to be recovered to the Engineering Department budget. 11. Fire Safety Policies for Exhibitions (Starwood Hotels & Resorts or Local). Exhibitor rules such as: forbidding items to be affixed to walls or ceilings, all electrical equipment to be properly grounded, etc. The Chief Engineer or designee is responsible to ensure that each client has received the agreed upon services and only those in which payment has been made. 8. For Exhibitors requesting additional services at the last minute during a set-up, an additional exhibit services form must be completed and a late charge of 25% over regular rates shall be applied. It is the responsibility of the Convention Services Department to update the form and distribute. 9. Due to the short term nature of most banquet business, the 25 percent late charges are to be waived. 10. At the same time in which the Exhibit Service form is completed, the customer is also to be issued the following information: 12. The Engineering Department will develop by convention, group, or persons name a list of those clients who require services so that they can be properly scheduled. 7. PROPERTY OPERATIONS POLICIES AND PROCEDURES

FIGURE 1 – EXAMPLE EXHIBIT SERVICES FORM ELECTRICAL EXHIBIT SERVICES Mail to: Attn Chief Engineer EVENTS:_________________________________________________________________________EVENT DATES:______________________ NOTICE: 1. Order must be made 10 days prior to date of installation 2. Payment must be made in accordance with the hotel’s credit policy. 3. There will be a 25% increase in regular price for each unit ordered during the move-in of your show . COMPANY:_______________________________________________________TELEPHONE NO:_____________________________________________________________________________________ STREET:__________________________________________ BOOTH OR ROOM NO. ______________________________________________________________________________________________ CITY:_____________________________________STATE:_____________________________________________________________ZIP_____________________________________________________ AUTHORIZED SIGNATURE______________________________________________________________________________________________________________________________________________ CREDIT CARD NO:______________________________EXP.___________________________________________________ ELECTRICAL POWER AVAILABLE AT THE SHERATON SEATTLE TOTAL CAHRGES $_______________________________________________________________________________________________ 120 volts single phase 60 cycle alternating current. 8.2 % TAX $________________________________________________________________________________________________ 208 volts single phase or three phase 60 alternating current. TOTAL EXPENSE $__________________________________________________________________________________ 240 volt s single phase 60 cycle alternating current (Grand Ballroom only). 120/208 Wye three phase 60 cycle alternating current. Total $ 225.00 200 AMP $ 175.00 150 AMP $ 125.00 100 AMP $ 70.00 60 AMP $ 60.00 50 AMP $ 50.00 40 AMP $ 40.00 30 AMP $ 30.00 20 AMP Price 15V Dedicated Circuit Quantity Total $ 450.00 200 AMP $ 350.00 150 AMP $ 250.00 100 AMP $ 140.00 60 AMP $ 120.00 50 AMP $ 100.00 40 AMP $ 80.00 30 AMP $ 60.00 20 AMP Price 208/240V (Single Phase) Dedicated Circuit Quantity

Cont… of Page 3 of 3 GENERAL CONDITIONS Electrical Services Rates quoted for connections cover bringing of service to the booth. Should it be necessary to run lines into booth for hooking/convention services manager. Service will be installed on a time and material basis. Rates for electricians $ 35.00 per hour from 8:00 A.M. on weekdays. Time and one half will prevails after 4:30 P.M. on weekdays, Saturdays, Sundays, and holidays ($ 52.50 per hour). NOTE: The Starwwod Hotels & Resorts assumes no liability for failure of electrical sources located at the hotel are suitable for any particular purpose. ALL CHARGES SUBJECT TO 8.2 % TAX ACCOUNTING COPY – WHITE ENGINEERING COPY – YELLOW CUSTOMER COPY – PINK CONVENTION SERVICE COPY - GOLDENROD Total $ 450.00 200 AMP $ 350.00 150 AMP $ 250.00 100 AMP $ 140.00 60 AMP $ 120.00 50 AMP $ 100.00 40 AMP $ 80.00 30 AMP $ 60.00 20 AMP Price 120/208V (3 Phase) Dedicated Circuits Quantity $ 15.00 $ 125.00 $ 75.00 $ 25.00 $ 45.00 PRICE LABOR (See GENERAL CONDITIONS) Materials (See GENERAL CONDITIONS) 3 Wire Grounded Extension Manlift & Operator (Flat Charge) Manlift(Flat Charge) TV Signal (Flat Charge) Hang Banner (s) (Flat Charge) OTHER SERVICES QUANTITY

The Controller is to allocate cost to the responsible department. 5. If it is determined that the damage was preventable, the Chief Engineer is to complete a Property Damage Report Form as in Figure 1. 2. The Property Damage Report Form is to be completed as follows: DAMAGED EQUIPMENT/PROPERTY – Description of damage. DATE DAMAGE REPORTED LOCATION OF DAMAGE – Area of hotel/property where damage occurred, i.e. laundry, kitchen, ballroom, etc. DESCRIPTION/DETAILS OF DAMAGE – Concise, accurate description of damage of item (s) or area (s). 3. The Chief Engineer must determine whether or not the damage could have been prevented by proper training and/or supervision. 2. The Chief Engineer is to establish the cost for repair and/or replacement. 3. A Damage Report Form must be submitted to the General Manager for approval, and a copy sent to the head of the department responsible. 4. The Chief Engineer is to assess the damage and determine if it is normal wear and tear or the result of employee abuse . 1. PROCEDURES The policy applies to all damage caused by negligence and is not classified as normal wear and tear. 1. STANDARDS: The Chief Engineer .is to implement, control and administrative the Property Damage Policy. POLICY: To curtail abuse and misuse of equipment and/or property, by charging repair expense to the responsible department. This will increase employee sensitivity to costs; and the net will result in reduced operating expense. PURPOSE: Section: ADMINISTRATION PROPERTY DAMAGE Subject: PROPERTY OPERATIONS POLICIES AND PROCEDURES

PROPERTY OPERATIONS POLICIES AND PROCEDURES In case the damage requires immediate attention, work should be completed and the Property Damage Report form completed at a later date. 7. A copy of each Property Damage Report is to be maintained in department files. 9. After completing the above, both the Department Head and the Chief Engineer are to sign the report and submit it to the General Manager for review and signature. 4. After repairs and/or replacement work is completed, the actual total cost (including material, labour and outside contractors) is to be entered on the report. 5. The Property Damage Report is then submitted to the Controller, for signature and allocation of expense to the responsible department. 6. The Chief Engineer must ensure that R&M is not charged with the associated costs, and if repairs are completed prior to the General Manager’s approval, the costs are to be recovered to the R&M budget. 8. ESTIMATE COST OF REPAIR/REPLACEMENT – Enter cost estimate, including material and labour. Enter estimated replacement cost if item needs to be replaced. CAUSE OF DAMAGE – Indicate the cause of damage, if it can be determined; otherwise, describe probable cause. Also include comments such as: has similar damage occurred previously; was incident preventable; discussion with Department Head etc . x Section: ADMINISTRATION PROPERTY DAMAGE Subject:

Figure 1. – PROPERTY DAMAGE REPORT FORM ______________________________________________________________________ ___________________________________ DAMAGED EQUIPMENT/PROPERTY: DATE REPORTED: _____________________________________________________________________________________________________________________________ LOCATION OF DAMAGED: _____________________________________________________________________________________________________________________________ DESCRIPTION/DETAILS OF DAMAGE: ________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________ ESTIMATED COST OF REPAIR/REPLACEMENT:_____________________________________________________________________________________ Repair Cost ________________________________________________Replacement Cost ____________________________________________________ _____________________________________________________________________________________________________________________________ CAUSE OF DAMAGE/COMMENTS: ___________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________ DEAPRTMENT:________________________________________________________________________________________________________________ ACCOUNT NO.________________________________________ ACTUAL COST ___________________________________________________________ __________________________________________ _____________________________________________________ CHIEF ENGINEER DATE HOTEL CONTROLLER DATE __________________________________________ _____________________________________________________ DEPARTMENT HEAD DATE GENERAL MANAGER DATE Number: 1.6 Page: 3 of 3 Section: ADMINISTRATION Subject: PROPERTY DAMAGE

The Monthly Work Order Summary Form is completed as follows: Date of Issue – The date contract is issued. Contractor – Name of contractor/company. Cost – Includes all labour, materials, taxes and delivery costs associated with the contract. Reason – A brief description of the work, i.e. replace broken windows, roof repairs, condenser water pump rebuild, etc. Total Cost – Add total cost for the month for all work order contracts. Total Cost Year to Date – Add totals of each month year to date. 3. The monthly Work Order Contract Summary is to be completed for each Starwood Hotels & Resorts fiscal month , See Figure 1 . 2. The monthly Summary is to be utilized as aid in monitoring your monthly R&M expenses, developing the annual R&M budget and analyzing Department staffing (i.e. skill level, number of employees). 4. The Work Order Contract Summary report is to be completed monthly . 2. The Summary report is to be maintained on file. 3. Any work performed within the hotel by outside contractors which is expensed to Property Operations must be issued by a Starwood Hotels & Resorts Corporate Work Order Contract. Purchased Orders are not to be used for outside labour. 1. PROCEDURES Work Order Contracts must be used for all contracted labour. 1. STANDARDS: The Chief Engineer .is to implement the Work Order Contracts Summary Policy. POLICY: To monitor costs associated with contracted labour which is expensed to Property Operations. PURPOSE: Section: ADMINISTRATION WORK ORDER CONTRACT SUMMARY Subject: PROPERTY OPERATIONS POLICIES AND PROCEDURES

of 3 Number: 1.7 Section ADMINISTRATION Subject: WORK ORDER CONTRACT SUMMARY If the department has a personal computer, or access to one, it is recommended that the Work Order Contract Summary be maintained on the computer. 6. The Monthly Work Order Contract Summary is to be maintained in Department files. 5.

The Monthly Work Order Summary Form is completed as follows: Date of Issue – The date contract is issued. Contractor – Name of contractor/company. Cost – Includes all labour, materials, taxes and delivery costs associated with the contract. Reason – A brief description of the work, i.e. replace broken windows, roof repairs, condenser water pump rebuild, etc. Total Cost – Add total cost for the month for all work order contracts . Total Cost Year to Date – Add totals of each month year to date. 3. The monthly Work Order Contract Summary is to be completed for each Starwood Hotels & Resorts fiscal month , See Figure 1 . 2. The monthly Summary is to be utilized as an aid in monitoring your monthly R&M expenses, developing the annual R&M budget and analyzing Department staffing (i.e. skill level, number of employees). 4. The Work Order Contract Summary report is to be completed monthly . 2. The Summary report is to be maintained on file. 3. Any work performed within the hotel by outside contractors which is expensed to Property Operations must be initiated by a hotel purchase order. 1. PROCEDURES Work Order Contracts must be used for all contracted labour. 1. STANDARDS: The Chief Engineer .is to implement the Work Order Contracts Summary Policy. POLICY: To monitor costs associated with contracted labour which is expensed to Property Operations. PURPOSE: Section: ADMINISTRATION WORK ORDER CONTRACT SUMMARY Subject: PROPERTY OPERATIONS POLICIES AND PROCEDURES

of 3 Number: 1.7 Section ADMINISTRATION Subject: WORK ORDER CONTRACT SUMMARY If the department has a personal computer, or access to one, it is recommended that the Work Order Contract Summary be maintained on the computer. 6. The monthly Work Order Contract Summary is to be maintained in Department files. 5.

FIGURE 1 – MONTHLY WORK ORDER CONTRACT SUMMARY FROM EXAMPLE WORK ORDER CONTRACT SUMMARY For the Month of: _________________________________, 19 _______________ ______________________________________ Chief Engineer Page 3 of 3 Number: 1.7 Section ADMINISTRATION Subject: WORK ORDER CONTRACT SUMMARY Total cost year to date: Total Cost: Reason Cost Contractor Date of Issue

MONTHLY LETTER scheduled into the following sections (sample as per Figure 1): RED FLAG ITEMS Identify any serious department problems, delays, hazards or incidents. If there is nothing to report, write NONE . KEN FIXIT List number of guest rooms completed versus monthly quota. If unable to complete quota, state reasons. REPAIR LOG Indicate current status of the repair log. If not current, give reasons and state when repair log will be up to date. PREVENTIVE MAINTENANCE Give the status of the schedule established for the month. If unable to complete work scheduled, explained and indicate when work will be up to date. 1. The Monthly Report will be completed each month . 2. The Monthly Report will be submitted to the Divisional/Regional Director of Engineering and Hotel General Manager no later than three (3) days following Fiscal closing. 3. The MONTHLY REPORT will consist of the following: PROCEDURE: The Monthly Report form will be used . 1. STANDARDS: The Chief Engineer will implement the MONTHLY REPORT policy. POLICY: To provide a system for reporting the current status of the Engineering Department to the Divisional/Regional Director of Engineering and the hotel General Manager. PURPOSE: Section: ADMINISTRATION MONTHLY REPORT Subject: PROPERTY OPERATIONS POLICIES AND PROCEDURES

of 19 Number: 1.8 Section ADMINISTRATION Subject: MONTHLY REPORT FIRE PROTECTION PREVENTIVE MAINTENANCE Give the status of the schedule established for the month. If unable to complete work scheduled, explain and indicate when work will be up to date. WORK REQUEST Report number of request issued, completed and backlogs. SAFETY TAGS/LOCKOUT Report on the use and effectiveness of this accident prevention Policy. IN-HOUSE PROJECTS Describe briefly any major in-house projects involving the Engineering Department and indicate estimated completion dates. CAPITAL PROJECTS Describe briefly capital projects in progress and indicate estimated completion dates. LIFE AND FIRE SAFETY PROTECTION COMPLIANCE SCHEDULE A list of legend number and a list of description are attached to this Policy. It is important that each description be read as you fill the compliance update sheet, as the information reflects the most recent Starwood Hotels & Resorts Policy regarding Life and Fire Safety. Upon receipt of the report (each month) the information will be reviewed including the projected date of compliance for those items not in compliance. A six months report depicting the percentage of compliance of all hotels will be generated an d sent to all Chief Engineers and General Managers for information. 2.

FIGURE 1. – MONTHLY LETTER EXAMPLE TO: REGIONAL DIRECTOR OF ENGINEERING DATE: FROM: DOE/CE COPY: GENERAL MANAGER SUBJECT: MONTHLY REPORT FOR (month) RED FLAG ITEMS Trash compactor controls not in compliance with OSHA and Starwood Hotels & Resorts Standards. Contractor advised to immediately install constant-pressure push button and access door interlock. POLICY/PROCEDURE STATUS Ken-Fix-It – Quota for the month is 166 rooms. Due to vacation schedule, only 150 were completed. Will complete full quota this month. Repair Log – All entries posted and log up-to-date. Age and repair history on kitchen exhaust fan indicates replacement necessary. Preventive Maintenance – All weekly sheets for the month were completed. Fire Protection Preventive Maintenance – All weekly schedule sheets for the month completed. Work Request – Policy functioning property except for minor problem with duplicated work requests. Will review procedure at next Department Head Meeting. Safety Tag/Lockout – Program being strictly enforced. Department members understand the importance of the system and use tags and lock-outs. PROJECT STATUS Inhouse Projects – Installing floor to ceiling book shelves in accounting office. To be completed by March 15. Capital Projects – Project No. 88-4 (Security safes in guest rooms closets) 60 percent complete. Full completion expected by April 1 st . Page 3 of 19 Number: 1.8 Section ADMINISTRATION Subject: MONTHLY REPORT

Compliance Schedule Legend Numbers Floor and wall penetrations sealed Fire dampers installed in ductworks Duct doors fire rated Floor slabs in duct shafts Guest room doors fire rated Escape/Exit doors fire rated Guest room door closer for compartmentation Shaft wells fire rated enclosures Emergency exits to street level Atrium smoke exhausting system Atrium underside floors with smoke detectors Areas separated by fire doors, walls and floors Hazardous areas separated by rated enclosures Smoke detectors installed throughout Heat detectors in kitchens Manual alarm stations in public areas and BOTH Centralized fire alarm control stations Fire control panels attended continuously Detection and protection systems on emergency power Fire alarm annunciation in all areas Guest on same floor alerted of fire Building-wide evacuation for building < 3 stories high Emergency broadcasting to all occupants Elevators return to street level upon alarm Fire alarm to fire department automatically Dead end corridors less than six meters Fire escape exit signs provided Fire exit sign size and illumination Escape signs lighted and on emergency power Minimum of 2 exits per floor Fire sprinklers provided to all areas Sprinklers to Sheraton fire safety standards Minimum residual pressure for sprinklers Automatic kitchen hood extinguisher Transformer and electrical rooms protected Hose reel in all areas Standpipes in all emergency stairways Portable extinguishers provided in all areas Portable extinguishers location All areas within 30 meters of fire hose Water supply at 2270 L/min (500 GPM) for 30 minutes minimum Water pressure at minimum of 448 KPA (65 PSI) Grade a water supply Secondary water storage minimum 30 minutes Fireman elevator available Fire extinguishing system signals to alarm panel Interior finish materials certified Conformance to local codes Fire prevention P.M. program implemented Employee fire brigade training program implemented Page 4 of 19 Number: 1.8 Section ADMINISTRATION Subject: MONTHLY REPORT

Life & Fire Safety Protection Compliance Schedule Page 5 of 19 Number: 1.8 Section ADMINISTRATION Subject: MONTHLY REPORT Are all the areas of different uses separated by fire resistive doors, walls and floors? (Areas of different uses are: residential, restaurants, storage, office, kitchens, plantrooms). 12. Smoke detectors are provided for each underside floor protruding into the atrium? 11. Smoke exhaust system provided? 10. Do all emergency exits open directly to street level? If an atrium of more than 2 floors exists is the following true: 9. Are all shaft in the hotel protected by 2-hour fire rated enclosures? Ventilation shafts Electrical wiring shafts Mechanical equipment shafts Rubbish shafts Linen chutes Dumb waiters Elevator shafts 8. Are all guest room doors provided with automatic self-closing devices for compartmentation purposes? 7. Are all escape door/emergency exit doors fire rated to 1 ½ hours? 6. Are all guest room doors fire rated to 1 hour? 5. Are floor slabs constructed in all the pipe duct and service shafts? 4. Are all pipe and service duct doors fire rated to 1 hour? 3. Are fire dampers provided in heating, ventilation and air conditioning ducts, which pass through fire barrier wall of 2 hour fire rating and above? 2. Are all penetrations formed by conduits, piping and duct work passing through fire rated floors and walls sealed off with fire rated sealant? To the full thickness of the wall? 1. Compartmentation Description Legend Number

of 19 Number: 1.8 Section ADMINISTRATION Subject: MONTHLY REPORT Are all escape signs illuminated and also on the emergency power supply system? 29. Are all Exit signs prominently displayed? 27. Is the maximum travel distance in any dead end corridor less than 6m? 26. Are all fire exit signs of the correct size and illumination characteristics as per Starwood Hotels & Resorts Fire Safety Standards? 28. Will the fire alarm signals be automatically transmitted to the local fire department? 25. Will all the elevators in the building return to street level when a fire alarm is activated? 24. Escape Routes and Emergency Power Are there at least two independent fire exits provided on every floor? 30. Is an emergency broadcasting system available for communication with all the occupants of the building? 23. For buildings less than three (3) stories in height only, will the actuation of the fire alarm automatically sound the building-wide evacuation alarm? 22. Are all guests on the same floor of the alarm, as well as the floor above and below, alerted when a fire alarm is activated? 21. Is fire alarm annunciation provided in all areas as per Starwood Hotel & Resorts Fire Safety Standards? 20. Are the fire detection and fire protection systems on the emergency power supply? 19. Is the central fire control panel located in a room which is constantly attended by trained personnel? 18. Is there a central control station to monitor the fire detection and fire protection system? 17. Are manual alarm stations provided in public areas and BOTH as per Starwood Hotels & Resorts Fire Safety Guidelines? 16. Are heat detectors provided in all kitchens? 15. Are smoke detectors provided in all following areas? Guest rooms and corridors Public areas Offices Assembly areas (function rooms) Back of the house areas Mechanical and electrical rooms Restaurants Storage areas 14. Are all hazardous areas separated from other parts of the building by fire resisting barriers of 2 or 3 hours? 13.

of 19 Number: 1.8 Section ADMINISTRATION Subject: MONTHLY REPORT Is the minimum water supply pressure at the most remote standpipe hose connection more than 448 kpa (65 psi)? 42. Is the water supply for the standpipe system sufficient to provide at least 1.89 cu.m./min (500GPM) for at least 30 minutes? 41. Is the water supply for the fire protection system a dual feed supply? (from two separate sources) 43. Are all areas in the building within 30 meters reach of a 25mm or 40mm fire hose? 40. Are all portable fire extinguishers located in a permanent position, free of obstructions, clearly visible and within easy reach? 39. Are portable fire extinguishers of the correct type provided in all areas? 38. Are stand pipe systems provided in all emergency stairways as per Starwood Hotels & Resort Fire Safety Standards? 37. Are 1 inch hose reels provided in the building in all the following areas as per Starwood Hotels & Resorts Fire Safety Standards? Guest room corridor Public areas Back of the house 36. Are the transformer and electrical switchboard rooms protected with any of the following systems: Halon Portable extinguishers Smoke Detectors CO2 Dry Chemical Sprinklers 35. Is an automatic extinguishing system provided for all kitchen hoods? 34. Is the minimum residual pressure of at least 103 kpa (15psi) available at the highest sprinklers? 33. Does the design for the automatic sprinkler system meet with Starwood Hotels & Resorts Fire Safety Standards? 32. Is an automatic sprinkler system provided for all the following areas? Guest rooms and corridors Public areas Offices Assembly areas (function room) Back of the house areas Mechanical and electrical rooms Restaurants Storage areas Kitchens 31. Fire Extinguishing System

of 19 Number: 1.8 Section ADMINISTRATION Subject: MONTHLY REPORT Is the Starwood Hotels & Resorts Employee Fire Brigade Training Program in effect? 50. Is the Starwood Hotels & Resorts Fire Prevention Preventive Maintenance Program in effect as per Sheraton’s Safety – Security Loss Control Manual, Section 4.11a? 49. Are all buildings of the property constructed in compliance with local building codes relating to fire resistive construction by building class, size and occupancy? 48. Have materials used for: interior finishes, carpets, furniture cushions, draperies, upholstery fabrics, bed covers, bed mattresses, wallcoverings, been tested for flame retardation and toxic fume generation? Are fire rating certificates available? 47. Is the operation of any part of the extinguishing system, i.e.: fire pumps, flow switches, tamper switches, hose reels, kitchen extinguishing systems, etc. automatically signaled to the central fire alarm control panel? 46. Is there an elevator available for the dedicated use by the local fire brigade for fire fighting purposes? 45. In case storage tanks supplement the street mains as a secondary water source for fire protection, is the duration of the secondary water supply at least 30 minutes? 44.

Life & Fire Safety Protection Compliance Schedule For the Month of: ________________ 199 _______ Page 9 of 19 Number: 1.8 Section ADMINISTRATION Subject: MONTHLY REPORT 24 23 26 25 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 Projected Date of Compliance If item is not in Compliance what is the current Status? Comply Yes/No Legend Number

of 19 Number: 1.8 Section ADMINISTRATION Subject: MONTHLY REPORT 50 49 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 32 31 30 29 28 27 Projected Date of Compliance If item is not in Compliance what is the current Status? Comply Yes/No Legend Number Date Chief Engineer

Environmental Health, Safety & Security Committee Meetings The Environmental Health, Safety & Security Committee should be held once a month a meeting, preferably at the same time and place each month. The meeting should last no longer than one hour. The chairman prepares an agenda and distribute it in advance to assure a well-organized, productive meeting. The General Manager is urged to attend as many meeting as possible. The purpose of this meeting is to review the preceding month’s accidents, to identify hazards and document them, to develop corrective action, and to follow up until the hazards are controlled or eliminated. It is essential that the minutes represents a complete record of all items and recommendations emerging from the discussions in order to assure effective, comprehensive and corrective actions. This detailed record does not only provide a vehicle to follow up on recommendation but also becomes a legal record of preventive measures taken in the interest of guest, employees and Fire Safety. Instructions for completing the minutes are on the following pages. In order to maximize the Committee’s productivity, it is recommended that the Chairman follows carefully this outline and related instructions. While doing so the efficiency will be maximized and repetition of previous discussions or deviation from relevant issues will be avoided. An example of a hotel Environmental Health, Safety & Security Committee Meeting minutes in accordance with the form is located in the Safety & Security Loss Control Manual, Section 4. Each hotel should build up their reports according to this example. As an ongoing follow-up procedure, each member of the Committee should communicate with superiors and employees about the pertinent items discussed within the meeting. Page 11 of 19 Number: 1.8 Section ADMINISTRATION Subject: MONTHLY REPORT

Instructions for Preparing Minutes of the Environmental Health, Safety & Security Committee Meeting Name of Hotel :__________________________________________ Date of this meeting: ________________________________ Date of last meeting: _____________________________________ Members Present : Position: Name Position (Names and positions of permanent members attending.) Members Absent: Position: Name Position (Names and position of permanent members not attending, reason for absence, and substitutes’ name and position.) Introduction of guests and invited employees. (Names and position of employees invited to participate this month and names of outside guests). Review of Accidents, Security Incidents and Inspection Checklists Review of Accidents This is a monthly analysis of all guest and employee accidents that were reported on the Accident Summary sheets and Accident Investigation forms as well as near-misses that were observed or brought to a member’s attention. All causes should be discussed in order to undertake the appropriate action. Numbers of lost working days per accident should also be recorded. In order to have an effective discussion about employee accidents, the following should be kept in mind when receiving the Accidents Investigation form: Where did the accident happen? How did the accident happen? What unsafe conditions and unsafe acts were involved? Was the employee properly trained for the job? Was the employee doing what he/she was supposed to do at the time of the accident? Where was the supervisor and other employees during the accident? Was the injured person in good health on the day of the accident? What temporary measures should be taken to prevent reoccurrence? What should be done to prevent on a permanent basis similar accidents? Was immediate notice given to the insurance company? B. Security Incidents (To be listed on a separate page) All security incidents should be reviewed for common sense solutions and preventive measures. Page 12 of 19 Number: 1.8 Section ADMINISTRATION Subject: MONTHLY REPORT

C. Inspection Items Requiring Discussion Planned inspections are required to detect in a systematic and timely manner. The inspector should be the supervisor who knows his/her area of responsibility and what conditions to look for. However, it is recommended that assignments be rotated at least every six months for the benefit of a fresh perspective because a department can become too familiar to a supervisor and a hazard may be overlooked. As hazards are discovered, immediate steps should be taken to correct them. The solution should get at the root of the problem- not just be a superficial remedy. It is the Committee’s responsibility to monitor inspections, discuss those inspection items requiring committee action, and assure that necessary corrections are made. In the Safety & Security Loss Control Manual you will find: A master checklist for general hazards A master checklist for fire prevention Specific individual departmental checklists to be used as a supplement to the master sheets. This checklists are provided as a guide from which each hotel is expected to develop its own checklist. While the checklist was developed based on the most commonly found deficiencies in hotels, they are not inclusive. No hotel should assume that by using the checklist as they will have met all mandatory occupational safety and health requirements of their country, state, city or region. It is the responsibility of each hotel to develop its own checklists based on the standards appropriate for its geographic location and the characteristics of the hotel. Please note that space has been left at the end of each checklist for use for hotels in adding their own questions. Items Completed Since Last Meetings This includes all items completed in a satisfactory manner since the last meeting. If the steps taken are not permanent solutions, the items should then be included in the “Pending Items” section. Pending Items This is a review of those hazards or problems identified but not yet controlled or solved due to time problems, complexity of steps involved, or other delays. Items will remain in this category until completed and reported in the above section. Adequate reasons are to be given for each delay. If the committee finds that an identified hazard cannot be corrected within ninety (90) days, alternate recommendations, (such as training) are to be developed. Miscellaneous This is a discussion of items not mentioned above such as review of new governmental requirements, outside speakers, establishment of first aid classes, safety campaigns/programs, review of new training materials, update and/or review of Starwood Hotels & Resorts Safety and Security procedures, etc. Whenever these discussions results in a decision and an action item, these items are to be listed under the “New Items” section Page 13 of 19 Number: 1.8 Section ADMINISTRATION Subject: MONTHLY REPORT

New Items This is a statement of all new items stemming from the discussions held for the above sections or mentioned at this time. All items should be recorded for appropriate follow-up. Assignments and due dates for completion and should be included. Review of Loss Control Manual or Other Environmental Health, Safety/ Security-Related Material The Chairman will review any pertinent safety/security material received from headquarters or elsewhere with the group. Review of the Loss Control Manual will be conducted as needed. The invited employees will be encouraged to review the manual at their convenience. Each member of the Committee should be provided with a 3 ring (or similar) binder to be called the Environmental Health, Safety & Security Committee Notebook. The Committee members are to lace the meeting form, All Committee Meeting Minutes, and other safety materials in the binder for future reference or transfer to members, Committee members are to bring this binder to each meeting. Attachments: All items referred to as attachments in this section are located in the Starwood Hotels & Resorts Safety & Security Loss Control Manual Section 4. The distribution of Minutes of Meetings shall be in accordance with Corporate/Divisional requirements. Note: The above form must be followed. Use as many pages as necessary to provide the above information. Page 14 of 19 Number: 1.8 Section ADMINISTRATION Subject: MONTHLY REPORT

Instructions for Filling Out Monthly Accident and Incident Report (M.A.I.R) This report indicates the actual number and classification of occupational related injuries, illnesses or incidents which have occurred during the calendar month. Enter the totals as follows: Classification Definition First Aid Treatment administered by a person of some knowledge about First aid, Registered Nurse or Medical Doctor in which treatment is limited to: -Application of Antiseptics on first visit to a doctor or nurse. -Bandaging on any visit to a doctor or nurse -Treatment of burns of first degree. -Compresses, hot or cold, on first visit to a doctor or nurse only. -Use of elastic bandage on first visit to a doctor or nurse only. -Removal of foreign bodies, not imbedded, or irrigation of eye. -Removal of foreign bodies from wound by tweezers or other simple techniques. -Use of non-prescription medications. -Observation of injury on second or subsequent visit -Use of ointments applied to abrasions to prevent drying or cracking. -Tetanus shots, initial or boosters alone -Hospitalization for observation (no other treatment than first aid). -X-ray which is negative. B. Medical Without Injuries requiring more advance treatment by a registered nurse or medical doctor. Advance treatment Lost Workdays includes: ( Excluding Date of Injury) -Antiseptics applied on second or subsequent visit to a doctor or nurse. -Treatment of burns of second or third degree, -Butterfly sutures (stitches) -Compresses, hot or cold, on second or subsequent visit to a doctor or nurse. -Cutting away dead skin (surgical debridement) -Diathermy treatment. -Removal of foreign bodies if embedded in eye. -Removal of foreign bodies from wound by a physician because of depth of embedment, size or shape of object (s) -Treatment for infection -Prescription medications used -Soaking, hot or cold, on second or subsequent visit. -Sutures (stitches) -Whirlpool treatment -X-ray which is positive. C. Total Lost -Occupational illness or injury, other than a fatality, which results in lost workdays, not including the date of injury. Workdays Cases This Month Page 15 of 19 Number: 1.8 Section ADMINISTRATION Subject: MONTHLY REPORT

D1. Total Lost The number of occupational injury or illness related workdays lost this month. Workdays a/b a = Days lost from this month ‘s cases (excluding date of injury) b = Days lost from accidents which occurred in previous month (s) D2. c/d The number of occupational injury or illness related workdays lost year-to-date. c = Days lost from this year’s cases (excluding date of injury) d = Days still lost from accidents which occurred in previous year (s). E. Fatality Occupational injury or illness resulting in death. (Notify TSC Safety Department within 8 days). F. Fire Fire losses of any amount. (Forward written report to TSC Safety Department within 24 hours. Major Fires- Notify TSC Safety Department IMMEDIATELY. G. Other Accidental incidents involving physical losses to building and equipment, or business interruption due to windstorm, flood, riot, loss of utilities, etc. H. Number of Total number of employees covered by this report Employees I. Injuries/ Public Liability accidents, including food claims and fatalities. or Fatalities (All fatalities must be reported to TSC Safety Department within 8 hours). J. Property Loss Any guest losses due to theft, damage or misplacement of property. Incidents The Monthly Accident and Incident Report must be attached to the General Manager’s Monthly Letter and the Safety Committee Minutes. These must be forwarded to TSC Safety Department within 7 days after the end of the month being reported on. Page 16 of 19 Number: 1.8 Section ADMINISTRATION Subject: MONTHLY REPORT

Starwood Hotels & Resorts management practices, Starwood Hotels & Resorts has established three critical goals: Improve Fire and Life Safety Reduce the Amount of Pollution We Generate Correct Identified Environment and Safety Problems Promptly In order for Starwood Hotels & Resorts to measure progress in these areas. Starwood Hotels & Resorts has established four statistical measures of which three apply to Starwood Hotels & Resorts as further described in the attached. We have combined the former Starwood Hotels & Resorts (MAIR) Monthly Accident and Incident Report and the statistics now required monthly by Starwood Hotel& Resort into the Monthly Environment & Safety Metrics Report . So far, reporting compliance has been satisfactory. However, questions generated from the hotels indicate that further explanation of some of the measurement categories is required: Question: Why change the former monthly Accident Frequency Index Formula from (B + C) x 100 x 12 to (B + C) x 100 ? H x N H Answer : The former formula resulted in an index that showed the year’s average accident index if the accident trend as established in the (calculated) month would continue. The Starwood Hotel’s & Resort-required formula shows the actual percentage of accidents during the reported month. (This is not a typographical error as some thought). Please note the requirement to calculate and report year-to-date Accident Frequency Index still continues.

Division Engineers Director of Technical Services August 2007 Page 2 Question 2: What constitute “Cost of Managing Waste”? Answer : The Cost of Management Waste includes all waste from food and hotel operations, including hazardous waste, ordinary solid waste, on-site waste treatment, and waste removal, and disposal of off-site waste treatment cost. The cost of all waste handling associated with hotel labor should be included. Although ideally all hotels would use exactly the same waste cost handling criteria, it is more important that the hotels are consistent in using ( month to month) the same cost measurement criteria so each hotel can measure its own progress in waste (cost) reduction. Question 3: Why are we (Starwood Hotels & Resorts) interested in obtaining these new statistic? Answer : Primarily, by identifying total waste management costs, we can establish incentives and goals to reduce, through the appropriate purchase of materials, recycling, and efficient work practices, our negative impact on the environment. Further adjustment of the statistical reporting frequency and formulas may need to be done to make the numbers as meaningful as possible. In the meantime, however, please provide the hotel with your assistance to ensure efforts are being made to meet the three goals and make the reported numbers as credible as possible. Best regards, Note : The Monthly Environment & Safety Metrics Report replaces the former Monthly and Quarterly Accident and Incident Report . We have a reporting obligation to Starwood Hotels & Resorts, so please encourage the hotels to send their reports to us promptly.

Environment and Safety Metrics Implementation Guide Introduction We have begun integrating Environment and Safety (ES) concerns (environmental protection, industrial hygiene, safety, and fire using statistical measures (metrics), we will track progress in meeting three critical ES program goals: Improving safety. Reducing the amount of pollution we generate. Correcting identified ES problem promptly. Two of the metrics identified are currently being computed on a regular basis; the data used to compute the remaining metrics are already being collected by most Starwood Hotels & Resorts units. The guide explains the metrics, and their computation and presentation format; and the process of setting targets (goals) for them. Also included is a schedule for implementing the ES metrics. Responsibilities and Reporting Implementation of this integration effort and the reporting of progress in achieving ES goals is an operating management responsibility. Initially, company presidents are to submit to their respective senior Starwood Hotels & Resorts HQ executives the proposed metrics adapted for their operations, describing the specific wastes and chemicals their units will track. After approval by Starwood Hotels & Resorts HQ, company presidents are to submit proposed goals for 2008 for each of their metrics. Companies must include descriptions of the approved metrics and the goals for 2008 in the next Operating Plan, using agreed upon reporting formats. Monthly progress reports are to be submitted upon full implementation of metrics in 2008 When performance is below the target, backup charts and information must be used to explain gaps, and the actions to be taken, or the resources needed, to close them. Environment and Safety personnel at all levels will provide technical assistance and support to assure timely implementation and full communication of management decisions regarding the integration of ES concerns into management functions.

ES Metrics The five initial metrics Starwood Hotels & Resorts will address are 1) injury severity, 2) injury frequency, 3) cost of managing process waste, 4) volume of materials of concern purchased, and 5) consolidated action plan delinquency. Four of the five are required for all Starwood Hotels & Resorts operating companies. The “volume of materials of concern purchased” is only required for manufacturing companies. Companies are to follow the instructions provided in this guide to calculate each of the metrics, and, where indicated, chose as appropriate factor for their operations. Beginning in April, companies are to collect the needed data, calculate the metrics, and promptly report to Starwood Hotels & Resorts Headquarters the result of the initial calculations, along with any suggested improvements. Setting Goals The trial period will provide the bases for improvement targets (goals) for each of the metrics. ES goals will be set after the appropriate metrics have been determined for each of the companies. Goals will be a challenge for each company to achieve, and will require effort consistent with other business goals. Environment and safety personnel will give full support to line managers in identifying cost-effective alternatives to achieve ES goals. Application of the Starwood Hotels & Resorts Process Safety and Pollution Prevention analytical process should be considered in this effort. Implementation Schedule The following are the steps the companies and Starwood Hotels & Resorts HQ will take this year to implement ES metrics and further the integration of ES concerns into business management: Companies develop the bases for the materials of concern and begin gathering ES data. (April) Companies report initial data for the April period and propose improvements in the metrics to Starwood Hotels & Resorts Headquarters. (May) Starwood Hotels & Resorts Headquarters reviews companies’ ES data and makes appropriate changes in the metrics, as required. (May-June) Starwood Hotels & Resorts HQ establishing ES goals for 2008 (August) Companies incorporate metrics into 2007-08 Operating Plans. (September-November)

Metric: Injury Severity (IS) Description: This measure tracks the severity of injuries suffered in lost-time accidents, as an indication of the impact accidents are having upon productivity and cost of labor. Application: The measure is required for all operating companies. Data should be recorded at each site and consolidated for the company report. Computation: Either use the Starwood Hotels & Resorts injury and Illness, and Lost Workday Indices ( See Starwood Hotels & Resorts HES Management Practices 20.4), or compute directly. IS = Starwood Hotels & Resorts Lost Workday Index ; ≠ D Starwood Hotels & Resorts Injury and Illness Index B + C D = days of work lost C = number of lost-workday cases If computed directly, the values must be adjusted each month to assign any lost workdays in the current month to lost-workdays cases from any prior month. Computation frequency: Monthly, calculate new values and update the 12-month running average. Construct a graph with the following information: the monthly values the 12-month running average the 12-month running average for 1993 the goal for 1994 A sample chart is included. Reporting frequency: Provide in a separate monthly report and include in every Operations Review.

Metric: Injury Frequency (IF) Description: This measure tracks the number of accidents resulting in lost-time or medical treatment that occur per 100 employees. It is similar to the Starwood Hotels & Resorts Injury Index now in use. Application: This measure is required for all operating companies and should be recorded at each site. Computation: If = (B + C) x 100 H B = number of medical cases in the reporting period. C = number of lost-workday cases in the reporting period H = average number of employees in reporting period Compute the 12-month running average using the same formula. Computation frequency: Monthly, calculate new values and update the 12-month running average. Construct a graph with the following information: the monthly values the 12-month running average the 12-month running average for 1993 the goal for 1994 A sample chart is included. Reporting frequency: Provide in a separate monthly report and include in every operations Review.

Metric: Cost of Managing Process Waste (CW) Description: This measures tracks the cost of handling waste. The choice of this measure is based on the assumption that lowering these costs will result in the reduction in usage of the materials disposed or more effective use of them in internal processes. “Handling” is meant to include on-site waste treatment and material transfer costs, including the associated labor, as well as payment for off-site disposal or treatment. “ Process waste” is meant to include all waste, hazardous waste, ordinary solid waste, or a combination of the last two. Each company must define the specific components of its metric, subject to Starwood Hotels & Resorts HQ approval. Application: This measure is required for all operating companies and should be recorded at each site. Computation: CW = W P W = cost of handling waste (U.S> Dollars) P = number of units produced or sales (U.S. Dollars) in reporting period, chosen so that the computed value of CW will be greater than unity Computation frequency: Monthly, calculate new values and update the three-month running average. Construct a graph with the following information: The monthly values A three-month running average The three-month running average for December 1993 The goal for 1994 A sample chart is included Reporting frequency: Provide in a separate monthly report and include in every Operations Review.

FORWARD ONE COPY OF THIS REPORT BY THE 10 TH DAY OF THE MONTH FOLLOWING THE MONTH BEING REPORTED TO: Starwood Hotels & Resorts All treatment and ordinary solid waste and hazardous disposal costs, including labor. Cost of Handling Waste W Number of corrective action items (as described above) that should have been, but were not, completed within the reporting period. Delinquent Action Items U Number of corrective action items identified through Health, Environment & Safety Audits. Inspections by division or Starwood Hotels & Resorts Headquarters staff, insurance company or other external consultant, and completed on time within the reporting period. Action Items Completed On Time T Gross sales in 100K units (U..S. Dollars) Gross Sales P Number of Months Reported N Public liability incidents. (Notify Corporate Fire, Life Safety and Environmental Health Department immediately of a guest fatality. (written report due within 72 hours.) Insurance Reportable Guest Injuries, Illnesses, or Fatalities I This figure represents the average number of full-time equivalent employees, based on 40 hours per week. Year-to-date. (This number should be an average of the monthly figures reported on the hotel’s FRS Monthly Input form). Average Number of Full-time employees H Accidental releases of corrosive or hazardous products. Chemical Spills G Fire losses of any amount. Notify Fire, Life Safety & Env. Health Department within 24 hours. Report major fires immediately. Fires F Formal notice of deficiency or non-compliance by federal, state, or local governing agency (OSHA, EPA, etc.) Regulatory Citations E The number of workdays, excluding the date of injury or onset of illness, that employee would have worked but could not because of occupational injury or illness. Days lost from cases which occurred this month (excluding date of injury or onset of illness). Days lost this month from cases which occurred in previous month (s). Days lost (YTD) from cases which occurred this calendar year, Days lost (YTD) from cases which occurred in previous year (s). Total employee Lost Workdays D (a/b and c/d) Any occupational injuries or illness (other than fatalities) that result in lost workdays. Notify corporate Fire, Safety & Environmental Health Department Immediately if an employee fatality occurs. (Written report due within 72 hours). Employee Lost Workday Cases C Treatment (other first aid) administered by a physician or by a registered professional under the standing orders of a physician. Employee Medical Cases Without Lost Workdays B One time treatment and subsequent observation of minor scratches, cuts, burns, splinters, etc. provided by a physician or registered professional personnel Employee First Aid Cases A LEGEND

Date:_________________________________ Cc: G.M. Monthly Letter Safety Security Committee Corporate Safety-Security Dept. MONTHLY ACCIDENT AND INCIDENT REPORT Hotel/Location/Property No:_______________________ Month When Accidents/Incidents Occurred: _____________________ Safety Meeting Held ____________________________________ Date _____________________________________ Monthly Fire & Emergency Drill Held ______________________________________ Time/Date ______________________________ No. of Safety Recommendations Outstanding since last report _________________________________________________________ No. of Safety Recommendations Completed since last report __________________________________________________________ *See Reverse for explanations and definitions. *Deadline for submitting this report, together with Safety-Security Committee Meeting Minutes, is the 15 th of the month following the month being reported. Page 18 of 19 Number: 1.8 Section ADMINISTRATION Subject: MONTHLY REPORT *Employee Injury Index Regulatory Citations Receieved K Governmental Property Loss Incidents J Injuries and/or Fatalities I Guest Accidents/Incidents Number of employees (Full Time Equivalence) H Staffing Others G Fire F Incidents Fatality E c d a b Total Lost Workdays This Month D 3 4 1 2 Total Lost Workday Cases This Month ** C Medical Without Lost Workdays B Employee Injuries and Illnesses First Aid A Year to Date Last Year Same MO. Last Year Year to Date This Month Classification Category

Others: Page 19 of 19 Number: 1.8 Section ADMINISTRATION Subject: MONTHLY REPORT

2.0 PROGRAMS 2.1 Ken Fixit 2.2 Repair Log 2.3 Preventive Maintenance 2.4 Fire Protection Preventive Maintenance] 2.6 Safety Tag/Lockout 2.7 Thermo graphic survey

KEN FIXIT PROGRAM Saleable rooms are our most important source of profit, a whopping 70% of room revenue is profit! To protect this source of income the Ken Fixit Program has been made mandatory in every Starwood Hotels & Resorts property. Ken Fixit who only fixes faucets, locks and numerous other little things is actually a very important person. All the little things that Ken Fixit does is like polishing the proverbial apple and thereby keeps our product saleable. Without the guest room revenue, all the things we are doing don’t need doing. The Ken Fixit Program provides a fixed schedule and routine for maintaining function rooms and 25% of the guest room each month, while at the same time increases employee production. Production is increased by reducing “go for” time as tools and materials required are in the Ken Fixit cart. The Ken Fixit cart should have the following characteristics: large wheels to roll easily over carpets, in and out of elevators, over door sills and brief steps, etc. Ample storage space, especially drawers and bins should be provided. Provisions must be made to lock the cart against theft. The portable workshop may be ordered through the Starwood Hotels & Resorts Supply Company. The unit is manufactured by the Roll-On Manufacturing Corp. and has a quality and character to complement the prestige of Starwood Hotels & Resort. See Figure 1. Guest room preventive maintenance is scheduled on a room-to-room basis eventually completing the entire house. When the last room is completed, the cycle will be started over, enabling a thorough inspection and maintenance in each year. In some smaller properties, Ken Fixit might be a part-time assignment for a maintenance man and scheduled on a weekly basis. Since the principle of the cart is to avoid traveling back and forth between shop and rooms, a specific time each week should be set aside for stocking the cart to eliminate needless trips. Equipment to be carried in the cart includes a comprehensive check list and all tools and materials necessary for room maintenance. Ken Fixit should be an all-round mechanic and as such requires training. Since Ken Fixit probably has more guest contact than anyone else in the Engineering Department, the person chosen should be carefully selected. Do not block out the idea of a female Ken Fixit in selecting a responsible person for this position. The first day the Chief Engineer should go through several rooms completely with Ken Fixit showing him what to look for. During the first weeks, each trade should spend at least a few hours training Ken Fixit. The electrical shop may want to show him the location of the breaker panels and the proper tripping and resetting procedure, how to replace receptacles and light switches, safety precautions, etc. The locksmith should instruct Ken Fixit in the removal, disassembly, repair, and/or replacement of guest room locks. A paper hanger may show him how to re-glue, replace and repair vinyl wall covering. Other trades should instruct Ken Fixit in his duties until he can perform all phases of the work required. Not to be overlooked during the training period is proper personal appearance and guest relations. Ken Fixit is responsible for leaving the guest room in perfect condition. Any deficiency that will take an excessive amount of time to correct or is beyond Ken Fix it capabilities should be noted on a Work Request Ticket immediately. Such items may include upholstery and furniture repair, burn holes in carpet, painting of walls and television repair, etc. Tickets written on minor items should be turned in the next time Ken Fixit is in the engine room. Tickets written on major deficiencies should be telephoned in for more speedy repair. This procedure is thoroughly covered by the WORK REQUEST SYSTEM.

A quota system has been developed where 25% of the guest rooms are serviced each month by Ken Fixit; i.e. , four months should see all guest rooms receive the Ken Fixit treatment. For Ken Fixit purposes, a year consists of three periods each containing four months or eighty working days. Twenty working days make a month while five working days constitute a week. A comprehensive list of duties should be in the cart. This checklist is an in-house reporting and reference system. Each item is checked off as inspected and/or repaired. A sample check/list is included which should be customized to your specific needs. At the end of each week the check list is to be handled to the Chief Engineer. The check list is to be filed by date for one year in the Chief Engineer’s Office. At the end of the year these sheets should be placed in a binder and marked with the date and the words “ken Fixit”. At variable intervals, but not more than a week apart, the Chief Engineer should take along Ken Fixit and inspect a series of rooms freshly completed. Any deficiencies should be discussed at this time. It is suggested that at least ten percent of the rooms be inspected by the Chief Engineer in this manner. Rooms thus inspected should be set off with an asterisk on the Ken Fixit Monthly Report, Figure 2. Hotel : Name of the Property Date: Date report is filled out. Period: Period I January 1 – April 30 Period II May 1 – August 31 Period III September 1- December 31 No. of Rooms: The total number of guest rooms. Monthly Quota: The total number of rooms to be inspected by Ken Fixit for the month. A one-thousand room hotel would have a quota of 1000/80 – 12.5 rooms per day, 12.5 x 5 = 62.5 rooms per week, or 62.5 x 4 = 250 rooms per month. (25% of total number of rooms). Completed This Month: This means the total number of rooms that Ken Fixit Man has completed that particular month. % This Month: To arrive at the percentage, divide the number of completed rooms by the quota for that month, multiply by 100. Completed This Period: The total number of rooms that Ken Fixit has completed in a particular period. % This Period: Calculation is similar to the % This Month, where it is the “completed this period” figure divided by “No. of Rooms”. In other words, the 1000 room hotel at the end of the second month of that particular period, should have completed 500 rooms. Therefore, his % This period would be 500/1000 = 50%. Number of rooms inspected by Chief Engineer: Total number of rooms that have been inspected this month by the Chief Engineer after completion by Ken Fixit. Set off these room numbers below with an asterisk. % This Month: Percentage of rooms checked by Chief Engineer. Divide the number of rooms inspected by the Chief Engineer by the number of rooms completed by Ken Fixit.

KEN FIX-IT MAINTENANCE CHECK LIST AIR CONDITIONERS 1. Pneumatic Control – (Lubricate valve stem & 0-ring, check opening and closing) 2. Knob on Thermostat – (Secure) 3. Filter – (Clean) 4. Condense Water Drain – (Clean) 5. Hand Valves – (Check, to be open) LAMPS (PORTABLE) 6. Switches – (Check) 7. Lamp Socket – (Tighten) 8. Lamp Shades – (Repair or Replace) 9. Cord on Valance Light Pull Switch (Check, replace if necessary) 10. Cover on Valance Light – (Secure) 11. Bulb – (Replace if necessary) 12. Plugs – (Replace if necessary) SWITCHES AND RECEPTACLES 13. Outlet Wall Plates – (Change plates to match wall color, inspect, clean, secure) 14. Switches – Change plates to match wall color, inspect, clean secure) 15. Switches & Receptacles – (Replace missing screws) 16. Receptacles – Change if necessary) TELEVISIONS 17. Audio (Check radio channels) 18. Video (Check television channels) 19. Knobs (Replace if necessary) 20. Fine Tuning (Adjust if necessary) 21. Antenna Outlet (Secure plate) 22. Antenna Connectors (Check, repair if necessary) 23. Remote Control and Connections (Check) TELEPHONE 24. Dialing Instructions (Replace if necessary or broken) 25. Defects (Report any other defects to hotel operator). FURNITURE 26. Drawer Handles & Knobs (Check, replace, if necessary) 27. Drawer Guides (Lubricate if needed with FET) 28. Stains (Clean and Touch up) 29. Springs on Chairs (Check) 30. Marble Table Tops (Check, repair small defects) 31. Headboards (Check and secure) 32. Wheels (Check and secure) WINDOWS AND MIRRORS 33. Window Guides (Lubricate with FET) 34. Mirror Hangers (Check and secure) 35. Window Hardware (Check and secure) DRAPERY TRACK AND ROLLERS 36. Inspect and secure all drapery track and rollers.

CLOSETS 37. Sliding Door Tracks (Check and repair if necessary) 38. Floor Guides for Sliding Doors (Check) 39. Bumpers on Sliding Doors (Check) 40. Floor Door Stop (Check) 41. Wall Hooks (Check) DOORS (MAIN ENTRANCE, BATHROOM AND CONNECTING) 42. Handles (Check) 43. Lock Cylinder Set Screw (Check) 44. Hinges and Hinge Pins (Lubricate with FET and Secure) 45. Door Chain (Check, repair if necessary) 46. Lock Striker Plates ( Check and secure) 47. Night Latch (Check) 48. Door Frame Rubber Bumpers (Check, replace if necessary) 49. Fire Exit Plan (Check) BATHROOM 50. Bath Tubs Safety – Slipguard used. 51. Toilet Flush Valve (Check) 52. Toilet Cover Bumper (Check) 53. Seat Hinges (Check and Secure) 54. Toilet Seal (Check for evidence of leaks) 55. Bath Drain Plugs & Pop-Up (Check) 56. Mixing Valve (Secure Handles) 57. Mixing Valve Washers (Replace if necessary) 58. Hot and Cold Faucets (Check and/or replace “H” and “C” buttons) 59. Escutcheoon Plates (Secure) 60. Shower Enclosure, Tracks and Doors (Check) 61. Shower Enclosure Bumpers and Handles (Check) 62. Ice Water Mechanism (Check) 63. P Trap under basin (Check) 64. Drain Pop-Ups (Check) 65. Faucet Strainer (Clean and Replace) 66. Basin Bowl Hangers (Re-glue or resecure) 67. Toilet Paper Holder (Check) 68. Razor Blade Dispenser (Check) 69. Bottle Opener (Check) 70. Kleenex Holder (Replace or Resecure) 71. Floor and Wall Tile (Check) 72. Soap Dish and Grab Bars (Check and Resecure) 73. Towel Racks (Resecure) 74. Toilet Privacy Locks (Check)

BATHROOM SCALES 75. Check correct weight 76. Check mechanism under scales GENERAL CHECK 77. Baseboards (Check) 78. Carpet (Check) 79. Vinyl (Check) 80. Pictures (Check) 81. Ceiling (Check for cracks and/or peeling paint) 82. Paint (Check paint on walls and door casings)

Hotel ___________________ TELEPHONE TELEVISIONS SWITCHES AND RECEPTACLES LAMPS (PORTABLE) AIRCONDITIONING KEN FIXIT MAINTENANCE CHECK LIST 5. 4. 3. 2. 1. 10. 9. 12. 11. 8. 7. 6. 16. 15. 14. 13. 21. 20. 23. 22. 19. 18. 17. 25. 24.

DRAPERY TRACK AND RULERS WINDOWS AND MIRRORS FURNITURES 30. 29. 32. 31. 28. 27. 26. 35. 24. 22. 36. ROOM NO.

BATHROOM DOORS (MAIN ENTRANCE, BATHROOM AND CONNECTING CLOSETS 41. 40. 39. 38. 37. 46. 45. 44. 47. 43. 49. 48. 42. 70. 69. 68. 67. 65. 64. 63. 62. 61. 60. 59. 58. 57. 56. 66. 56. 55. 54. 71. 53. 52. 72. 51. 74. 73. 50.

GENERAL SCALE BATHROOM SCALES 76. 75. 78. 80. 79. 82. 81. 77. ROOM NO.

MAINTENANCE CART IN ACTION Mounted Equipment Showing is CUSTOMER Applied to Middi Model SPECIFICATION – MIDDI MODEL – Std. color, maintenance orange black drawers. 18” x 36” Top – 1/ 8” Masonite overlay – 37” high. 11 various size drawers – 1 1/2” x 7” modular. Total Locking Front Cover – Shown recessed. 12 Small Parts Pockets – each end. 12” x 2” Polyurethane Main Wheels – ND / H Ball Bearings. 5” x 1-5 / 8” POLY – on Nylon Casters. Floor Brake – Chrome hardware. Body – 16 – 18 gauge Steel – Wt. 234 lbs. 10 years structural guarantee. Optional colors and Drawer choice available. Baby buggy balance to walk over door sills, elevator cracks, steps and other obstructions. Designed for smooth, easy rolling – heavily loaded – over carpeted floors. OTHERS SIZES – SAME SPECIFICATIONS 18” X 28” Top – 8 DRAWER - JUNIOR MODEL 18” X 44” Top - 14 DRAWER - UTILITY MODEL 24” x 44” Top – 14 DRAWER - SENIOR MODEL ROLL – ON…. … .the only carts with the easy rolling big wheel and famous baby-buggy balances.

KEN FIXIT MONTHLY SUMMARY REPORT Hotel______________________ Date___________________________ Period______________________ No. of Rooms ___________________________ Monthly Quota __________________________________ Completed this month________________________________ % this month _________________________ Completed this month ________________________________% this period _________________________ No. of rooms inspected by Chief Engineer ___________________________________% this month _________________________ COMPLETED ROOM NUMBERS LEGEND NOTES Period I January 1 – April 30 1. Indicate rooms inspected by Chief Engineer by *. Period II May 1 – August 31 2. Reports must be mailed no later than 15 th of each month. Period III September 1 – December 31 Engineering Operations Chief Engineer ________________________________________ 470 Atlantic Avenue Boston, Mass. 02210 FIGURE 2

Each property is to purchase a mobile maintenance cart to be used as a portable workshop/tool bench. The cart must have the following characteristics: Large wheels to allow mobility over carpets, door sills and in and out of elevators. Ample storage space such as drawers and parts pockets, so that it can be organized for maximum efficiency. Locks to prevent theft of parts and materials. A brake so that it remains stationary when used as a work bench. Approximate size of the cart is to be 45 cm (W) x 90 (L) x 95 (H). 1. PROCEDURE The Ken Fixit cart is to be stocked with spare parts and materials that typically would be used to maintain the guest rooms and public areas. 2. The Chief Engineer is to inspect 10 percent of the completed Ken Fixit guest rooms and the public areas monthly . 6. 25 percent of all guest rooms will be inspected and deficiencies corrected monthly. 4. The Ken Fixit check lists will be used for guest rooms and public area. 3. All public areas will be inspected and deficiencies corrected monthly. 5. The Ken Fixit Mechanic will inventory the cart weekly . 2. The Ken Fixit Summary Report will be completed monthly. 7. A Ken Fixit mobile maintenance cart will be stocked with required spare parts and materials and appropriate hand tools for daily use by the Ken Fixit Mechanic. 1. STANDARDS: The Chief Engineer is to implement and maintain the Ken Fixit program. POLICY: Promote quest satisfaction by ensuring that guest rooms and public are maintained in excellent condition and in working order. PURPOSE: Section: PROGRAMS KEN FIX-IT Subject: PROPERTY OPERATIONS POLICIES AND PROCEDURES

of 12 Number: 2.1 Section PROGRAMS Subject: KEN FIX-IT The guest contact areas to be inspected monthly. The Ken Fixit Mechanic will use a Public Area Maintenance Check List and checkmark each item inspected and/or repaired. 8. The Chief Engineer is to inspect 10 percent (minimum) to the recently completed guest rooms and all public areas throughout the course of each month. Any deficiencies noted are to be brought to the attention of the Ken Fixit Mechanic. This will help top ensure that the program is working properly and identify further training needs. 13. It is the Ken Fixit Mechanic’s responsibility to leave the room cleaned in perfect order after completion of any work performed. 12. At the end of each week the Ken Fixit Mechanic is to provide the Chief Engineer with the completed Check Lists. At the end of each month the completed public area Check List must be submitted. 14. At the end of each month the Chief Engineer is to complete the Ken Fixit Summary Report as in Figure 4 . A copy of the report must be maintained on file. 15. Any noted deficiency requiring an excessive amount of time to repair, or beyond the Ken Fixit Mechanics ability is to be noted on a work request ticket and returned to the Chief Engineer. Major problems are to be telephoned in to the Engineering Department to ensure that they are handled expeditiously. 11. At the start of each week , the Chief Engineer will provide the Ken Fixit Mechanic with a list of rooms to be completed. The rooms which have been completed are to be tracked to ensure that there is no duplication of rooms (until the entire hotel has been completed). 10. As a rule of thumb, one full-time Ken Fixit Mechanic is required per 500 rooms. This position is a full-time position; therefore, the Ken Fixit Mechanic is not to be used for other work unless in an emergency situation. 9. The Ken Fixit Mechanic is to be use a Maintenance Check List for each room and checkmark each item inspected and/or repaired. 7. A monthly quota of 25 percent (minimum) of the guest rooms must be completed. The quota will ensure that every guest room is completed three(3) times per year. 6. The Chief Engineer must develop a comprehensive Ken Fixit Check List for the rooms and public areas. Examples of check lists are shown in Figure 2 and 3. These examples are to be used as a guidelines in developing check lists tailored specifically to your hotel. 5. The Ken Fixit tool list, as in Figure !, is to be used as a guideline in purchasing the necessary hand tools which are to be maintained on the cart. 4. It is the responsibility of the Ken Fixit Mechanic to inventory the cart weekly to ensure that it is fully stocked and to advise the Chief Engineer of parts and materials that needs to be purchased as inventories are depleted. 3.

of 12 Number: 2.1 Section PROGRAMS Subject: KEN FIX-IT Description Set of typical Hand Tools/Pouch 110 mm Vise (mount on top of cart) 40 mm Wood Wallpaper Roller Set (4) Nail Sets 250 mm Bastard Cut Flat File/Handle 350 mm Flat Mill File/Handle 250 mm Putty Knife 150 mm Block Plane Awl 3/8” Drive Ratchet 17 mm Deepwell Socket (12pt) 13 mm Deepwell Socket 10 mm Deepwell Socket 25 mm Nylon Paintbrush 50 mm China Bristle Paintbrush Artist Paintbrushes (assorted) 200 mm Dry Wall Knife 3/8” Cordless Drill Hacksaw/Blades Keyhole Saw Caulking Gun/Tub Caulk 10 m Flat Extension Cord Oil can Picture Tool (s) TV Cable Security Tool TV “Box” Programming Tool Volt/Ohm Multimeter Digital Thermometer Wire Strippers Utility Knife Carpet Scissors Portable Vacuum Cleaner FIGURE 1. – KEN FIXIT TOOL GUIDELINE

of 12 Number: 2.1 Section PROGRAMS Subject: KEN FIX-IT 1. ENTRY Door Condition/Appearance Lock Operation Night Latch Security Latch Door Closure/Hinges Door Bumper Door Viewer Emergency Evacuation Signage Security Signage Wall covering Baseboard/Cove Carpet Ceiling Ceiling Light Light Switch and Cover Threshold Rate Card/Holder CLOSET Door Condition/Appearance Door Track Shelf And Rod Wall covering Baseboard/ Cove Carpet Ceiling Ceiling Light Light Switch and Cover Tie Rack BATHROOM Door Condition/Appearance Door Operation Door Hardware/Hinges Door Bumper Robe Hook Vanity Condition/Appearance Mirror Light Fixture/Bulbs Light Switch/Cover GFI Receptacle and Cover Sink Sink Faucet/Aerator Sink Valves/Stopper Water Temperature Water Pressure Towel Bars FIGURE 2. – KEN FIXIT GUEST ROOM CHECK LIST GUIDELINE

of 12 Number: 2.1 Section PROGRAMS Subject: KEN FIX-IT Make-up Mirror Hair Dryer Television Telephone Tissue Dispenser (s) Bottle Opener Tub/Non-slip Tub Faucet/Valve/Stopper Shower Head Soap Dishes Wall Tile/Grout Toilet/Seat Toilet Ballcock/Water Level Wall Covering Baseboard/Cove Floor Covering Ceiling Exhaust Grille Threshold Grab Bar secure BEDROOM Ceiling Wallcovering Baseboard/Cove Carpet Connecting Door Condition/Appearance Connecting Door Lock Operation Connecting Door Hinges Window Condition/Appearance Drape Operation/Hardware A/C Unit Condition/Appearance A/C Operation/TStat Setting A/C Filters A/C Drain Pan A./C Grille (s) Bed Frame/Headboard Tables, Desk, Chairs Condition Dresser/Armoire Condition Sofa Condition Night Stand Condition Table Lamp (s) Switch/Shade/Bulb/Plug Floor Lamps (s) Switch/Shade/Bulb/Plug Radio/TV Operation/Plug (s) Light Switch (s) Cover (s) Outlets and Covers Telephone Operation/Jack Mirrors Artwork Alarm Clock/Correct Time

of 12 Number: 2.1 Section PROGRAMS Subject: KEN FIX-IT WET BARS Cabinet Condition/Appearance Counter Top Condition/Appearance Sink Condition/appearance Sink Faucet/Valves Operation/Appearance Ceiling Ceiling Fixture/Bulbs Light Switch/Cover GFI/Outlet/Cover Wall-covering Baseboard/Cove Floor covering Refrigerator Operation/Temperature Coffee Maker/Plug LIFE SAFETY Smoke Detector/Operation Emergency Speaker Sprinkler Head (s)

of 12 Number: 2.1 Section PROGRAMS Subject: KEN FIX-IT GUEST ROOM CORRIDORS Door Frames Room Numbers Wall covering Baseboard/Cove Floor covering Ceiling HVAC Grilles Light Fixtures/Bulbs Signage Outlet/Cover Plates Vending Area Floor Covering Vending Area Walls/Ceiling Ice Machine Soda Machine Floor Drain Smoke Detectors Fire Alarm/Speakers Sprinkler Heads Pull Stations Magnetic Fire Door Holders/Proper Sequencing Shafts Doors Condition 2. ELEVATOR FOYERS Ceiling Wall covering Baseboard/Cove Floor Covering Light Fixtures/Bulbs Indicator Lights Signage Doors and Frames Fire System Devices Art Work/Advertising Telephone Furniture Smoke Detector Sprinkler Heads Life Safety Sign ELEVATOR CABS Floor Covering Wall Treatment/Millwork Ceiling Lighting Emergency Telephone Indicator/Control Panel Cab Numbers LOBBY/CIRCULATION AREA Ceiling Wall covering Baseboard/Cove Floor Covering FIGURE 3. – KEN FIXIT PUBLIC AREA CHECK LIST GUIDELINE

of 12 Number: 2.1 Section PROGRAMS Subject: KEN FIX-IT Light Switches/Cover Plates Outlets/Cover Plates Windows Drapery Operation/Hardware Millwork Furniture Art Work Doors/Door Frames Door Hardware/Hinges/Closure Signage Telephones Exit Signs Smoke Detectors Fire Alarm/Speakers Pull Station Sprinkler Heads FRONT DESK AREA Ceiling Wall covering Baseboard/Cove Floor Covering Light Fixtures/Bulbs Light Switches/Cover Plates Outlets/Cover Plates Desk Top Millwork Drawer/Door Operation Door (s)/Door Frame (s) Door Hardware/Hinges/Closure Telephones Exit Signs Sprinkler Heads Fire Alarm/Speakers Smoke Detectors Hold Up Alarm 6. BUSINESS CENTER Ceiling Wall covering Baseboard/Cove Floor Covering Light Fixtures/Bulbs Light Switch (s)/Cover Plates (s) Outlets/Cover Plates Millwork Furniture Equipment Telephone Door/Door Frame Door Hardware/Hinges/Closure Smoke Detector Sprinkler Heads Fire Alarm/Speakers

of 12 Number: 2.1 Section PROGRAMS Subject: KEN FIX-IT LOUNGE (S) Ceiling Wall covering Baseboard/Cove Floor Covering Millwork Furniture Light Fixtures/Bulbs Light Switches/Cover Plates Outlets/Cover Plates Bar Tops (s) Television (s) Telephone (s) Art Work Signage Smoke Detectors Fire Alarm/ Speakers Exit Signs 8. RESTAURANTS Ceiling Wall covering Baseboard/Cove Floor Covering Millwork Furniture Light Fixtures/Bulbs Light Switches/Cover Plates Outlets/Cover Plates Signage Art Work Sprinkler Heads Smoke Detectors Fire Alarm/Speakers Exit Signs 9. GIFT SHOP Ceiling Wall covering Baseboard/Cove Floor Covering Light Switches/Cover Plate (s) Outlets/Cover Plates Equipment Millwork Smoke Detectors Fire Alarm/Speakers Sprinkler Heads 10. MEETING ROOMS Ceiling Wall covering Baseboard/Cove Floor Covering Light Fixtures/Bulbs Light Switches/Cover Plates

of 12 Number: 2.1 Section PROGRAMS Subject: KEN FIX-IT Outlets/Cover Plates Drapery Operation/Hardware Windows Doors/Door Frames Door Hardware/Hinges/Closure Pocket Walls Furniture Millwork Public Address Speakers A/C Outlets/Cover Plates Exit Signs Sprinkler Heads Fire Alarm/Speakers Smoke Detectors Dimmers/Operation PUBLIC RESTROOMS Door Operation/Conditions Door Hardware/Hinges/Closure Ceiling Wall covering Baseboard/Cove Floor Covering Light Fixtures/Bulbs Light Switch (s)/Cover Plate (s) Outlets/Cover Plates Stall Partitions/Hardware Toilets Operations/Hardware Urinals Operation/Hardware Threshold Tissue Holders Grab Bars Sink Counter Top Faucets/Aerators/Valves/Stoppers Paper Towel Dispenser Paper Towel Receptacle Soap Dispensers Mirror Furniture Millwork Sprinkler Heads Fire Alarm/Speakers POOL AREA Door (s) Condition/Appearance Door (s) Hardware/Hinges/Closure Ceiling Wall covering Baseboard/Cove Deck Light Fixtures/Bulbs Light Switch (s)//Cover Plate (s) Outlets/Cover Plates Furniture Millwork Telephone/Direct Switch PBX Safety Signage Safety Equipment

of 12 Number: 2.1 Section PROGRAMS Subject: KEN FIX-IT Exit Signs Smoke Detectors Sprinkler Heads Fire Alarm/Speakers Gate/Self-Closing HEALTH CLUB Door (s) Operation/Appearance Dorr (s) Hardware/Hinges/ Closure Ceiling Wall covering Baseboard/Cove Floor Covering Light Fixtures/Bulbs Light Switch/Cover Plate Outlets/Cover Plates Equipment Telephone/Direct Switch PBX Safety Signage Lockers Shower Stall Wall Tile/Grout Shower Head Shower Valve/Soap Dishes Shower Curtain Rod Stall Partitions/Hardware Urinal Operation/Hardware Sink Counter Top Sink Faucet/Aerator/Valves/Stoppers Drains Exit Signs Sprinkler Heads Smoke Detectors Fire Alarm/ Speakers

FIGURE 3 – KEN FIXIT SUMMARY REPORT KEN FIXIT MONTHLY SUMMARY REPORT Hotel _______________________________________________ Date ____________________________ Period ________________________ Number of Rooms ____________________________________________________________ Monthly Quota ___________________________ Completed this month ____________________________________________ % this month _________________________________________ Completed this period ____________________________________________ % this period _________________________________________ No. of Rooms inspected _________________________________________________ % this month __________________________________ COMPLETED ROOM NUMBERS LEGEND Period I January 1 – April 30 Period II May 1 – August 30 Period III September 1 – December 31 NOTES 1. Indicate rooms inspected Chief Engineer by *. Chief Engineer __________________________________ Page 12 of 12 Number: 2.1 Section PROGRAMS Subject: KEN FIX-IT

A list of all equipment serviced by the Property Operations Department is to be compiled. 2. This policy is to be set up prior to developing the Preventive Maintenance Program as the information needed will be extracted from the Repair Log. 1. PROCEDURE A Repair Log Data Sheet, as in Figure 1, is to be completed for each piece of equipment from the list referenced above. 3. The Repair Log Data Sheet is completed as follows: Service – List service provided such as compressed air, exhaust, domestic hot water, etc. Type Machine – Describe equipment, such as hot water boiler, supply fan, laundry dryer, etc. Equipment I.D. No. – The equipment identification number is taken from the Equipment Schedule which is developed in accordance with the Starwood Hotels & Resorts tag number system, as per figure 3. Location - Give the specific area in which the equipment is located, such as main mechanical room, roof, etc. Serial No. – List the serial number, as identified by the equipment manufacturer. Model No. – List the model number, as identified by the equipment manufacturer. Make – The name of the equipment manufacturer. 4. The Repair Log is to be reviewed annually. 4. A Master Copy of the Repair Log Data and Record Sheets will be maintained and kept current. 3. Replacement parts and labour repair costs associated with the repair of piece of equipment are to be recorded on the Repair Log Record . 2. A Repair Log Data Sheet will be completed for each piece of equipment serviced by the Department. 1. STANDARDS: The Chief Engineer is to develop and maintain the Repair Log Program. POLICY: To provide an equipment inventory index and cost breakdown history of all major equipment. The Repair Log is to be used as the basis in determining if a piece of equipment should be replaced. PURPOSE: Section: PROGRAMS REPAIR LOG Subject: PROPERTY OPERATIONS POLICIES AND PROCEDURES

of 10 Number: 2.2 Section PROGRAMS Subject: REPAIR LOG Note : When complex machinery is involved, it may be necessary to list additional information on the back of the Repair Log Data Sheet. An example would be a laundry washer using both a primary and a secondary drive system. In this case, primary specifications should be listed on the Specifications – All applicable data pertaining to the equipment, such as Voltage – voltage in volts. Amperage – Current in amps. Phase – Number of phase. Pressure – Operating pressure in pascals. Horsepower – Power developed expressed as HP. RPM – Revolutions per minute. Drive – The method of power transmission such ass belt, gear, direct. Belts – The size and number. Fuse – Type and size Lubrication – Type oil, grease, etc. as specified by the equipment manufacturer. Filters – Type and number. Fluids – The working fluid of the system such as hydraulic oil, refrigerant 22, etc. 1. Date Purchased – The date the equipment was put into service (if available). Purchase Cost – The equipment cost at the time of purchase (if available). Preventive Maintenance Procedure – The functions and time intervals. Function – The specific maintenance items are to be performed, as recommended and/or specified by the equipment manufacturer. Interval – The corresponding maintenance time frames for each specific functions, such as weekly, monthly, etc. Special Instructions – Instructions of a specific nature particular to the equipment’; such as: caution, automatic start, fan controlled by fire alarm; electrical disconnect is located in adjacent room; supply fan is interlocked with the exhaust fan and both must be restarted, etc.

of 10 Number: 2.2 Section PROGRAMS Subject: REPAIR LOG The above procedures pertain to any new equipment purchased. 10. It is recommended that the Repair Log Data sheets be inserted in clear plastic sheet protectors and stored in a three ring binder. The Repair Log Record Sheet is to be kept adjacent to its companion data sheet within the binder. 8. The Repair Log Record Sheet is not to include costs associated with preventive maintenance. Ensure that all outside labour and materials are included in addition to in-house labour and materials. 7. If the department has a personal computer or access to one, it is recommended that the Repair Log System to be computerized using the Chief Software. 11. The Repair Log is to be reviewed annually to determine the following: Effectiveness of the Preventive Maintenance. Quality of replacement parts. Potential for equipment replacement due to the cost breakdown history. 9. A Repair Log Record Sheet , as in Figure 2, must be maintained for each piece of equipment for which a Repair Log Data sheet has been completed. Equipment I.D. No. – The equipment tag number. Date – The date during which repairs were made. Work Performed – A description of work performed including parts and/or materials repaired and/or replaced. Hours – Total hours required to complete a repair. Materials- The cost of material and/or parts used to complete a repair. Labour – The labour cost associated with a repair. Cost to Date – The combined total cost to date for material and labour for all repairs completed. 5. The front page, and the information concerning secondary system on the back page. It is of utmost importance to list as much information concerning the equipment specifications as possible.

of 10 Number: 2.2 Section PROGRAMS Subject: REPAIR LOG Purchased Cost Date Purchased Make Model No. Serial No. Location Equipment Type Machine Service FIGURE 1. – REPAIR LOG DATA SHEET Interval Function PREVENTIVE MAINTENANCE PROCEDURE SPECIAL INSTRUCTIONS Fluids RPM Filter Horsepower Lubrication Presure Fuse Phase Belts Amperage Drive Voltage SPECIFICATIONS

of 10 Number: 2.2 Section PROGRAMS Subject: REPAIR LOG To date Labour Materials Cost Cost Hours Work Performed By Date FIGURE 2. – REPAIR LOG RECORD SHEET

FIGURE 3. – IDENTIFYING OF EQUIPMENT FOR PREVENTIVE MAINTENANCE The equipment number called the TAG NO is a 7 digit code which is used to identify a particular piece of equipment. The TAG NO is divided into three sets of codes as described below. All equipment in the hotel must be labelled with TAG NO, and strongly recommended to fix a permanent tag to the equipment such as plast or alu labels, but note that paintings or stickers are alternative means for some applications. Hotels with existing number system, which vary from the TAG NO, can be left with their system, but hotels which will install computerized maintenance systems have to convert to the new TAG NO SYSTEM. A chart code has been developed which is divided into 10n types of maintenance records as follows: TERRAIN AND BUILDING FOOD AND BEVERAGE EQUIPMENT AIR CONDITIONING TRANSPORT EQUIPMENT STEAM WATER AND GAS ELECTRICAL INSTALLATIONS VARIOUS EQUIPMENT FIRE AND SAFETY EQUIPMENT GUEST ROOMS ENGINEERING ADMINITRATION. It is essential that the equipment is divide into the above –mentioned types in order to maintain a uniform system throughout the division, thereby making support and reporting easier. The numbers used for each type of maintenance records are recommendation and can be adjusted to match the individual application. The first 3 digits of the TAG NO is a numeric code used to identify what type of equipment it is, e.g. the sprinkler pump will be type 810, the coffee machine in the restaurant type 260, the cooling tower type 350 and the drilling machine in the workshop type 740, etc. The next set of codes is a two digit alpha numeric code used to identify on which floor the equipment is located, e.g. 14 is on the 14 th floor, B1 could be basement 1, RT could be the roof top and CP could identify the car park. The third and last section of the TAG NO is a two digit code used as a serial number to separate this particular equipment from all other, e.g. 01 is the first equipment of this type on this floor while 02 will be the next, etc. Page 6 of 10 Number: 2.2 Section PROGRAMS Subject: REPAIR LOG

A power panel on the second floor will be labeled as follows: 640 for the type 02 for the location 01 for the first panel. Putting all together the TAG NO for this panel will be 640-02-01. In case there are two panels on the same floor the next panel would be 640-02-02, etc. For hotels which use – 1, etc. to describe the first basement a slash can be used as separator for the TAG NO (250/-1/01). The total outline of the system is described on the following page together with a sample list. Page 7 of 10 Number: 2.2 Section PROGRAMS Subject: REPAIR LOG

MAINTENANCE RECORD TYPES FOR USE WITH ANY MAINTENANCE SOFTWARE Page 8 of 10 Number: 2.2 Section PROGRAMS Subject: REPAIR LOG Other Electrical 699 Other Terrain & Building 199 Telephone Systemf 690 Garden, Road, Walks & Playground 190 PA & Small Power 680 Decoration, Windows & Mirrors 180 TV & Video 670 Signs 170 Light Indoor 660 Build in Furniture 160 Light Outdoor 650 Loose Furniture 150 Power Installation, DB Board 640 Surface inside 140 Substation 630 Surface outside 130 Batteries & Charger 620 Keys & Locks 120 Emergency Supply 610 Doors 110 6 ELECTRICAL INSTALLATION TYPE 1 TERRAIN & BUILDING TYPE Other Various Equipment 799 Other Food & Beverage 299 790 Mixers, Ice Cream & Scales 290 780 Reach in Cabinets & Counters 280 770 Cutter, Slicers, etc. 270 Banquet Equipment 760 Coffee Machine 260 Air Compressors 750 Dish/Glass Washers 250 Tools & Workshop Equipment 740 Range, Friture & Grill 240 Housekeeping Equipment 730 Oven & Convectomats 230 Laundry Equipment 720 Ice Cubers & Flakers 220 Health Club Equipment 710 Cooling & Freezing Installation 210 7 VARIOUS EQUIPMENT TYPE 2 FOOD & BEVERAGE TYPE Other Fire Safety 899 Other Air Condition 399 890 Pumps 390 880 Boilers 380 870 Package Units 370 Fire Extinguisher 860 Heating Installation 360 Hose Reel 850 Cooling Tower 350 Halon & CO2 system 840 Chilled water installation 340 Alarm System 830 Chillers 330 Smoke Exhaust 820 Exhaust Units 320 Sprinkler & Fire Water 810 Airhandlers 310 8 FIRE & SAFETY EQUIPMENT TYPE 3 AIR CONDITIONING TYPE

MAINTENANCE RECORD TYPES FOR USE WITH ANY MAINTENANCE SOFTWARE REV: Oct 89, Nov 89, Oct 91 Page 9 of 10 Number: 2.2 Section PROGRAMS Subject: REPAIR LOG Other Guest Room 999 Other Transport 499 990 490 980 880 970 Vehicles 470 960 Escalator 460 950 Façade Lift 450 Minibars 940 Compactor 440 TV & Radio 930 Pallet Trucks, Trolley 430 Bath Room Appliances 920 Service Lift 420 Fan Coils 910 Guest Lift 410 9 GUEST ROOM TYPE 4 TRANSPORT EQUIPMENT TYPE Other Administration 1099 Other Steam, Water & Gas 599 1090 590 1080 Oil Installation 580 1070 Gas Installation 570 Documentation 1060 Irrigation Installation 560 Drawings 1050 Swimming Pool & Fountain 550 Shift Routines 1040 Sewage & Storm Water 540 Daily Routines 1030 Public Bath Room 530 Computer system 1020 Water Installation 520 BEMS 1010 Steam Installation 510 10 ENGINEERING ADMINISTRATION TYPE 5 STEAM, WATER & GAS TYPE

MAINTENANCE RECORDS – SAMPLES 170-GF-01 Neon Sign Main Entrance 190-GF-01 Car Park 220-14-01 Ice Cuber 14 th Guest Floor 220-GF-01 Ice Cuber Main Kitchen No 1 260-TO-02 Coffee Machine Tower Lounge 310-B2-01 Air Handler for Laundry 310-B2-02 Air Handler Page 10 of 10 Number: 2.2 Section PROGRAMS Subject: REPAIR LOG

When the spread sheets have been completed and reworked to maximum efficiency, the Weekly Schedule Sheets, Shown as Figure 3 , can be completed. 4. From the Repair Log, compile a list of all equipment, respective equipment identification numbers, preventive maintenance functions and time intervals. This information is to be entered on the spread sheet shown as Figure 1 . 2. In order to ensure that each piece of equipment is serviced according to the manufacturer’s specifications, the Repair Log must be completed prior to developing the Preventive Maintenance Program. 1. PROCEDURE It is important that the work load is spread equally over a 52-week period, so that preventive maintenance is performed every week . By shifting the function time intervals horizontally, excessive work loads can be avoided . The number of spread sheets required is determined by the property size and the number of pieces of equipment included within the preventive maintenance schedule. See example Spread Sheet as in Figure 2 3. Each piece of equipment to be serviced on week one (1) is taken from the Spread Sheet and entered on a Weekly Schedule Sheet. Equipment name, Identification number and specific maintenance functions to be performed are to be entered. Week two (2) through fifty-two (52) are a week one necessary for most weeks. It is recommended that the completed Weekly Schedule Sheets be inserted in clear plastic sheet protectors, and the entire sheets are the Master Sheet . See example Weekly Schedule Sheets as in Figure 4 . 5. Preventive Maintenance Weekly Schedule Sheets are to be signed by the Engineering mechanic, dated and filed as proof of program compliance. 3. Preventive Maintenance functions are to be entered on the Preventive Maintenance Weekly Schedule Sheets and spread equally over a 52 week period, so that maintenance is performed every week. 2. Each piece of equipment is to be serviced in accordance with the manufacturer’s specifications and local conditions. 1. STANDARDS: The Chief Engineer is to develop and maintain the Preventive Maintenance Program for all equipment not covered by a maintenance service contract. POLICY: To reduce down time by minimizing mechanical failure, reduce operating costs by improving efficiency, extend the life of the equipment and maintain safety conditions. PURPOSE: Section: PROGRAMS PREVENTIVE MAINTENANCE Subject: PROPERTY OPERATIONS POLICIES AND PROCEDURES

The Sub-Master are to be filed in a dated binder and retained for one year in the Engineering Office. At the end of this year, the binders are to be put in permanent storage and kept for legal purposes. 9. AS each piece of equipment is completed, the employee enters his or her initials and the date of completion on the Sub-Master. Any additional work performed and/or needed is to be noted on the Sub-Master and a work request ticket written . The completed Sub-Master Weekly Schedule Sheet is then returned to the Chief Engineer, along with any work request tickets written. 7. Each week , the corresponding annual numerical Weekly Schedule Master Sheet is to be photocopied. This copy is to be called the Sub Master. The name of the employee responsible for completing the work is to be entered on the Sub-Master . Multiple copies of Sub-Masters may be required, which depends on the number of persons assigned to complete the work. 6. The Chief Engineer is to review each returned Sub-Master sheet to ensure the Preventive Maintenance has been completed and to note any additional work performed or work which requires scheduling at a later date. Any Work performed above and beyond preventive maintenance is to be entered in the Repair Log Record . 8. If the department has a personal computer or access to one. It is recommended that the preventive maintenance program be computerized using the Chief software. 10. Page 2 of 6 Number: 2.3 Section PROGRAMS Subject: PREVENTIVE MAINTENANCE

of 6 Number: 2.3 Section PROGRAMS Subject: PREVENTIVE MAINTENANCE WEEK NUMBER EQUIPMENT I.D. NO. FIGURE 1. – PREVENTIVE MAINTENANCE SPREADSHEET 1 2 6 5 4 3 2 4 3 2 1 8 7 6 5 7 8 9 4 0 1 3 0 9 2 0 9 8 7 6 5 4 3 2 1 1 0 9 8 7 6 5 4 3 2 1

of 6 Number: 2.3 Section PROGRAMS Subject: PREVENTIVE MAINTENANCE WEEK NUMBER EQUIPMENT I.D. NO. FIGURE 2. – SPREAD SHEET EXAMPLE x x x x x 1 x x x x x x 2 x x x x x x x 6 x x x x x 5 x x x x x x 4 X x x x x x x 3 x x x x x x 2 x x x x x x x 4 x x x x x 3 x x x x x x 2 X x x x x x x 1 x x x x x x 8 x x x x x 7 x x x x x x 6 X x x x x x x 5 X x x x x x 7 x x x x x x 8 x x x x x 9 x x x x x x x x 4 0 (Continue as Required) X X X X X X Hobart Mixer #10073 x x x x x Groen Oven/Steamer #3505 x Salamander Broiler #1 x x x x x x Southbend Range #424212 x x x x x x Southbend Fryer #38944 x x x x x x Champion Dishwasher r# 20kb. x x x x x x x x x x x x x x x x x x x x x x x Flatwork Ironer Maxima Plus 240 x x x x x x x x x x x x x x x x x x x x x x x Compressor #F240 x x x x x x Utility Press #UR - 47 x x x x x x 70lb. Gas Dryer #L36C D36 G x x x x x 150lb. Gas Dryer #L36C D42 G x x x x x x x x x x x x x x x x x x x x x x x 125lb. Washer/Extractor #42/24 FLA x x x x x x x x x x x x x x x x x x x x x x x 65 LB. Washer/Extractor #36-18 FLA 1 3 0 9 2 0 9 8 7 6 5 4 3 2 1 1 0 9 8 7 6 5 4 3 2 1

FIGURE 3. – WEEKLY SCHEDULE SHEET Week _____ Page 5 of 6 Number: 2.3 Section PROGRAMS Subject: PREVENTIVE MAINTENANCE Record any other work performed or needed at a future date Completed by Assigned by MAINTENANCE FUNCTIONS Equipment & I.D. No.

FIGURE 4. – WEEKLY SCHEDULE SHEET EXAMPLE Week __ 1 __ Page 6 of 6 Number: 2.3 Section PROGRAMS Subject: PREVENTIVE MAINTENANCE *Automatic Bearing Lubrication System Record any other work performed or needed at a future date Check: Planetary Oil Level; Transmission Oil Level; Slide Ways; Lift Screw and Hand Wheel Gear – Lubricate. Hobart Mixer # 10073 Check: Pilot Flame – Clean and adjust; Burner- Clean and Adjust; Main Gas Valve – Clean and Confirm Connection to Hood Suppression System. Southbend Range #424212 Check: Diameter of Pressinga Roll – Adjust; Conveyor Belts – Tighten; Sprocket and Pulley Alignment; Chains – Adjust and Lubricate; Water Level; Burner Assembly; Vee Belts – Wear and Tension; Ironing Belts – Wear and Tear; Exhaust System – Clean; Gear Box Oil Level. Ironer Max Plus 240 Check: Oil Level; Air Receiver-Drain; Belt Tension; Pulley and Pulley Set Screws; Safety Valves-Test; Air Intake Filter-Clean or Replace; Cooling Surfaces – Clean Intercooler, Aftercooler and compressor; Oil-for Contamination; Unloader; Unloader Pilot and Three-Way Valve. Compressor #F 240 Check: Air Filter-Clean; Drain Tank-Blow Down. Utility Press #UR-47 Check: Repeat above Steps 125lb Washex #42/24 FLA Check Programmer; Motor Mounts and Guard; Air Filter/Lubricator; ABLS* Lubricator; Vee Belt Wear & Tension; Air Filter Element; Brake Lining. 65lb. Washex # 36/18 FLA Completed by Assigned by MAINTENANCE FUNCTIONS Equipment & I.D. No.

The list to be used to complete the Spread Sheet , as explained in the Preventive Maintenance Policy 2.3 (See example spread sheet Figure 1 , Page 3 of 6, Preventive Maintenance Program 2.3). 4. The Spread Sheet is to be completed so that the work load is spread equally over a 52-week period. 5. All applicable equipment and minimum equipment maintenance schedules, as in Figure 1, are to be incorporated and followed explicitly. 2. An accurate list of all fire protection devices, including well defined locations, is to be compiled. 1. PROCEDURE The list of General Tasks, as in Figure 2, is to be incorporated into the Fire Protection Preventive Maintenance Program. 3. When the Spread Sheet is completed, the Weekly Schedule Sheets (See example shown in the Preventive Maintenance Policy 2.3, Figure 3, Page 5 of 6) are to be completed. Each device requiring Preventive Maintenance on wee (1) is taken from the Spread Sheet and entered on a Weekly Schedule Sheet. Device name, location and specific maintenance functions to be performed are entered. Weeks two (2) through fifty-two (52) are completed the same way. Multiple Weekly Schedule Sheets may be necessary. 6. The completed Fire Protection Preventive Maintenance Schedule are to be filed in a dated binder for one year in the Chief Engineer’s office. At the end of the year, the binders are to be put in permanent storage and kept for legal purposes. 4. The Preventive Maintenance Policy 2.3 format will be used. 3. This program is to be implemented as per the Fire Protection Maintenance Schedule. 2. This program is to be maintained separately from the Preventive Maintenance Policy 2.3 (except properties using the Chief Software. 1. STANDARDS: The Chief Engineer is to develop and maintain a Fire Protection Preventive Maintenance Program as per Starwood Hotels & Resorts Guidelines and applicable fire codes. POLICY: To provide a safe environment for hotel guest and employees, and to ensure the protection of hotel property and assets. PURPOSE: Section: PROGRAMS FIRE PROTECTION PREVENTIVE MAINTENANCE Subject: PROPERTY OPERATIONS POLICIES AND PROCEDURES

of 7 Number: 2.4 Section PROGRAMS Subject: FIRE PROTECTION PREVENTIVE MAINTENANCE The Chief engineer is to review each Sub Master Sheet returned to ensure that the Preventive Maintenance has been completed. 9. The Sub Masters are to be filed in a dated binder for one year in the Chief engineer’s Office. At year-end, the binders are to be put in permanent storage and kept for legal reasons. 10. Each week the corresponding annual numerical Weekly Schedule Master Sheet is photocopied. This copy is referred to as the Sub Master . The name of the employee who is responsible for completing the work is to be entered onto the Sub Master. Multiple copies of Sub Masters may be required, depending on the number of persons assigned to complete the work. 7. It is recommended that the completed Weekly Schedule Sheets be inserted into clear plastic sheet protectors and the entire program stored in a three ring binder. These Sheets are the Master Sheets . As each piece of equipment and/or general task is completed, the employee enters his/her initials and the date of completion on the sub master. The completed Sub Master Weekly Schedule Sheet is returned to the Chief Engineer. 8. If the Department has a personal computer and uses the Chief Software, all fire protection equipment of the property shall be identified under tag number series. 11.

of 7 Number: 2.4 Section PROGRAMS Subject: FIRE PROTECTION PREVENTIVE MAINTENANCE Inspect monthly Open and close annually Perform maintenance procedure semi-annually as recommended by manufacturer Hydrants (Private) Inventory taken and visual inspection monthly (sign and date extinguisher tag). Maintenance yearly by specialist contractor. Fire Extinguishers Test semi-annually, flow test System sprinkler Preaction/Deluge Detection Calibration Test – Every 5 years Pressure Gage (s) Water flow indicators tested every two months Sprinkler Flow Indicators Flow test quarterly as per NFPA 13 Chapter 2.6.1 Main Drains Test quarterly Indicator Post valves Re-racked annually Fire Hoses Visual inspection monthly. Sprinkler should be free from corrosion, foreign materials, paints and not bent or damaged. Sprinkler Heads Inspected yearly including float switch Fire Tanks Test weekly – Run Time minimum 30 minutes Diesel Fire Pump Sealed Valves – inspect weekly Locked Valves – Inspect monthly Tamper Switches – inspect and test monthly All Valves – annually valve stems should be oiled or grease. The valves shall be completely closed and reopened to test their operation and to distribute the lubricant Fire Standpipe Valves Inspect the following monthly: -Pump Test Header -Hose Connections -Roof Manifolds -Siamese connections Fire Department connections MAINTENANCE SCHEDULE EQUIPMENT FIGURE 1. – FIRE PROTECTION MAINTENANCE SCHEDULE Tested Monthly – Inspect the condition of the pump, bearings, staffing boxes, saction pipe strainers and the various other details pertaining to the driver and control equipment. Electric Fire Pump Test annually Preaction/Deluge System

of 7 Number: 2.4 Section PROGRAMS Subject: FIRE PROTECTION PREVENTIVE MAINTENANCE Pull stations operated by pulling handle Smoke detectors tested by operating test button or magnet (test set) Heat detectors tested by removal of fusile link (test set) Water flow switch tested by operating inspector; test valve on floor Tamper switch on sprinkler system, operated by turn valve ¼ turn Main fire alarm panel annunciated proper alarm zone Fire fighter’s telephone operated properly All fire alarm zones can be reset and confirmed free of trouble conditions. (If applicable) send alarm signals over telephone wires to the central stations or fire department to confirm operation Inspection Outline of Each Months 1/12 System Alarm Test (i.e. floors 1 through 3 tested If hotel is a 36 storey property) Visual inspection weekly Fire Alarm Stations Complete discharge and hydro-static tested every 12 years or sooner as required by code Fire Extinguishers Actual pull test every 3 months of all stations 1/12 total tested monthly so all units are tested at least yearly. Coded Pull Boxes 1/12 of Total Fire Alarm Stations and Detection Devices Inspect water level monthly In cold water, inspect heating mechanism (if applicable) daily Inspect condition of tanks bi-annually Gravity Tanks Inspect water level and pressure monthly In cold weather, inspect heat enclosure daily Inspect condition of tanks bi-annually Pressure Tanks Test semi annually Quick Opening Devices (a.k.a. Accelerators) Trip-Test annually in the Spring Full flow trip test every 3 years in the Spring Dry-Pipe Valves Test annually Antifreeze Solution Close valves in the Fall Open valves in the Spring Cold Water Valves Inspect air pressure and water pressure weekly in cold weather, inspect enclosure daily inspect priming water level quarterly. Dry/Preaction/Deluge Systems Test in the Fall Low-point Drains

of 7 Number: 2.4 Section PROGRAMS Subject: FIRE PROTECTION PREVENTIVE MAINTENANCE Monthly tested for heat and smoke reaction Automatic Fire Doors Checked every 6 months Other Fire Doors Monthly Inventory taken Fire Cart/Back Pack Yearly checked by gas company for closing Main Gas Valve Monthly rubbish removed and equipment cleaned ( not to be done by in-house employees ) Elevator Pits Every 2 months or more often if local conditions require Chemical Fire Proofing of Continuous Service Kitchen Exhaust Ducts Yearly Actual fire fighting by fire brigade and selected employees Fire Fighting Equipment As required, at least once a year Chemical Fire Proofing of Infrequently Used Kitchens Inspected, tested, bottle weight every 6 months Range Hood Fire Extinguisher System At least weekly Dirty filters removed, clean filters installed Kitchen Range Hood Filters Monthly (Documented evaluation of instructions in use and equipment) Fire Fighting Equipment Once a year Operate entire bell/voice system for 3 minutes on standby power if provided. Battery Test Tested every two months (voice tested if P.A. is provided). Entire system to be tested as during full evacuation of property. Pre-alarm Bells/ Speakers Once every 6 months Operate emergency lighting for 1 hour on battery standby Emergency Battery Lighting Weekly Perform hydrometer float test of battery cells. Check voltage and output of battery charger. Generator/Fire Pump Battery Full inspection at least monthly Escape Routes Including Exit Signs To be tested weekly and run for 30 minutes on load Emergency Generator (s)

of 7 Number: 2.4 Section PROGRAMS Subject: FIRE PROTECTION PREVENTIVE MAINTENANCE NOTE: These are minimum requirements. If local authorities require more frequent maintenance, above schedule should be changed accordingly. Daily to be checked for lint accumulation and to be cleaned. Laundry Equipment and Exhaust Ducts Monthly Doors to be cleared for proper closing Trash and Linen Chutes One day after arrival of a new staff member and in 3 months intervals thereafter. Monthly intervals for telephone operators and night staff. Fire and Emergency Procedure Updating and Training Safety inspected as required by codes or as determined by Starwood Hotels & Resorts Safety Department. Elevators Minimum yearly safety inspections as required by codes. Boilers and Pressure Vessels

FIGURE 2. – GENERAL TASKS The following list provides a general overview,. It may be expanded by considering the specific requirements of a particular hotel. The time periods mentioned are for reference only and may vary greatly, depending on the type of hotel and any local regulations. Page 7 of 7 Number: 2.4 Section PROGRAMS Subject: FIRE PROTECTION PREVENTIVE MAINTENANCE 1 to 4 weeks Kitchen areas must be checked for accumulation of combustible materials such as oil and grease, especially in hoods and ventilation ducts As required Property and functional cleaning procedures, in particular the punctual emptying of waste baskets, trash cans and ashtrays, must be checked (especially after festivities during exhibitions, etc.) 1 to 6 weeks All areas of the building must be inspected to detect any changes in fire load, accumulation of dirt or trash, etc. 2 to 8 weeks The proper designation of non-smoking areas must be checked Continuously The observation of no-smoking regulations must be checked As required The proper storage of grease and oil rags (i.e. approved containers) Daily, with room make-up The availability of emergency instructions in guest rooms (room cards) must be checked 1 to 6 weeks The availability of emergency instructions (safety measures) in guest rooms, corridors, lobbies, etc. must be checked and missing items must be replaced. 2 to 6 weeks Escape route identification must be checked and missing signs must be replaced, any obstructions must be removed. Monthly Simulated fire alarm drills should be conducted with as much realism as possible on each shift Yearly Emergency procedures must be tested for their effectiveness (i.e. bomb threats, evacuation drills.) Yearly All emergency plans should be checked, updated and coordinated with the fire department RECOMMENDED TIME PERIOD TASK

Employees are to be given a copy of this procedure and trained in its use at least annually. 4. Extreme caution is to be exercised in order to ensure zero mechanical state has been achieved. As an example, equipment which is hydraulic or pneumatic operated may need to be de-energized. 4. If more than one department member is working on the same equipment or system, each member must attach his/her respective safety tag and mechanical lock-out. 5. Before commencing any work that require shutting off electrical circuit breakers, disconnects, or closing of water, steam or gas valves, and any equipment which stores energy, the Engineering Department member must attach a signed and dated safety tag and mechanical lock-out. This will prevent the inadvertent start-up of equipment or system, which could result in personal injury or loss of life. 2. Safety tags and mechanical lockouts with non-identical padlocks are to issued top each member of the Engineering Department. A supply of safety tags is to be readily available within the maintenance shop area. A typical example of a safety tag, as in Figure 1, can be obtained from an electrical supply house. 1. PROCEDURE After the equipment has been affixed with a safety tag and mechanical lock-out, the department member will attempt to start the equipment, in order to ensure it has been properly immobilized. 3. Safety tags and mechanical lock-outs are to be used by outside contractors. 5. Safety tags and mechanical lock-outs are to be removed by the originator or the Chief Engineer ONLY . 3. Safety tags and mechanical lock-outs are to be affixed to equipment disconnects, valves, etc. prior to repairs and installations. 2. Safety tags and mechanical lock-outs are to be issued to each member of the department. 1. STANDARDS: The Chief engineer will implement and strictly enforce the Safety Tag Lockout Policy. POLICY: To prevent injury or loss of life due to the inadvertent start-up of equipment, or to systems being repaired and/or installed. PURPOSE: Section: PROGRAMS SAFETY TAG/LOCKOUT Subject: PROPERTY OPERATIONS POLICIES AND PROCEDURES

Ensure that any new equipment, purchased or overhauled, can accommodate mechanical lock-outs. 10. This policy applies to outside contractors working within the building. It is to be monitored and enforced without exception. 9. This policy is to be strictly adhered to. 11. Department employees are to be given a copy of this procedure and trained in its proper use and implementation at least annually. Training documentation must be maintained on life. 7. After the work has been completed, the safety tag and mechanical lock-out is to be removed by the originator or the Chief engineer; but, only after it has been thoroughly determined to be safe to do so. Removal by any other person is forbidden. 6. Documented procedure training must be provided for employees, other than the Engineering Department, who are working in areas affected by equipment, i.e. laundry, kitchen. 8. Page 2 of 3 Number: 2.6 Section PROGRAMS Subject: SAFETY TA/LOCKOUT

Figure 1. – SAFETY TAG EXAMPLE Page 3 of 3 Number: 2.6 Section PROGRAMS Subject: SAFETY TAG/LOCKOUT DANGER DO NOT REMOVE THIS TAG IT IS A VIOLATION OF PLANTRULES TO DO SO WITHOUT AUTHORITY WILL MEAN DICIPLINARY ACTION SEE OTHER SIDE PLASTICLIP DANGER DO NOT OPERATE SIGNED BY_________ DATE _____________ Thomas and Betts WTAG-71A

Provide copies of survey results to Divisional Engineer. 5. Ensure that any necessary work, identified in the survey, is completed as soon as possible. 6. Ensure that the data is recorded on video tape for later analysis and permanent storage of information. 4. Advise Divisional Engineer that all work has been satisfactorily completed. 7. Locate the nearest suitably qualified contractor to undertake the survey. Ensure that the contractor has the most modem and appropriate thermal imagers to achieve the highest quality results. 2. Identify and develop a schedule of all electrical distribution boards, switch gear, electrical panels and mechanical equipment where heat can be generated or lost unnecessarily. 1. PROCEDURE Coordinate the survey with other hotels in your area to reduce costs of surveys. 3. The Chief Engineer is to conduct an annual infra-red thermo graphic survey of all electrical distribution systems and major mechanical equipment. POLICY: To reduce the risk of fires and failure of electrical services and mechanical systems. PURPOSE: Section: PROGRAMS INFRA-RED THERMOGRAPHIC SURVEY Subject: PROPERTY OPERATIONS POLICIES AND PROCEDURES

3.0 SYSTEMS 3.1 Water Treatment 3.2 Pool & Spa Treatment 3.3 Water Fountain Treatment 3.5 Key Control 3.6 L.P. Bacteria

Close loop water system analysis tests will be conducted and recorded weekly and water chemistry will be adjusted accordingly. 5. Boiler water, feed water and steam condensate analysis tests will be conducted and recorded daily and chemistry will be adjusted accordingly. 4. Condenser water analysis tests will be conducted and recorded daily and water chemistry will be adjusted accordingly. 3. The water treatment service company must supply required chemicals and all other services identified in the procedure. 2. The services of a Water Treatment Company will be retained. 1. STANDARDS: The service company will supply the required chemicals as follows: Condenser Water Scale Corrosion Inhibitors – In most cases this will be of the molybdate/polymer/phosphonate type, suitable for operation in the pH range of 7.0 – 8.5 It will not contain free mineral acids or chromates. The use of acid is to be avoided unless approved by the Divisional Director. Condenser Water Microbiocides – Two functionally different microbiocides will be used on a rotating basis. Non-oxidizers are preferred, but bromine release chemicals are acceptables. Closed System Corrosion Inhibitors – A buffered boron nitrite corrosion inhibitor will be used. 2. A service contract is to be retained from a water treatment service company. 1. PROCEDURE The Chief Engineer will implement and monitor the Water Treatment Policy and maintain a water treatment service contract. POLICY: To extend the life of piping systems and related equipment through protection against corrosion, scale build up and microbiological growth and reduce operating costs by improved efficiency. PURPOSE: Section: SYSTEMS WATER TREATMENT Subject: PROPERTY OPERATIONS POLICIES AND PROCEDURES

of 5 Number: 3.1 Section SYSTEMS Subject: WATER TREATMENT The Chief Engineer will ensure the following is performed: Conduct daily analytical tests on the condenser water and adjust the water chemistry accordingly. The test is to determine total dissolved solids, pH and chemical inhibitor levels. Conduct daily analytical tests on the boiler water, feedwater and steam condensate and adjust chemistry accordingly. The tests are to determine the following: 4. The service company is to provide the following additional services: A monthly (minimum) service visit at which time all treated systems are to be analyzed and daily/weekly chemical log sheets reviewed. A field service report detailing findings and re-commendations must be prepared. Training of operating personnel in the proper chemical test procedure and instruction on the proper handling of chemicals in terms of safety and government regulations, including Material Safety Data Sheets (MSDS) or equivalent. Provide chemical test kit equipment and chemical log sheets for all applicable systems. Representation each time a cooling tower, water side of a condenser, chiller or boiler is open for inspection or overhaul. A field service inspection report detailing the effectiveness of the treatment program together with any recommendations prepared. Technical assistance for any water treatment problem upon request. A quarterly chemical system analysis of all treated systems performed in the service company’s corporate testing laboratory. 3. Boiler Oxygen Scavenger – This is a catalyzed sulfite product used to remove dissolved oxygen from the water. Boiler Corrosion and Deposit Inhibitor – Generally this is a multi-component formulation and is either a phosphate or polymer based products. Steam and Condensate Corrosion Inhibitor – A neutralized amine based products, food grade, must be used.

of 5 Number: 3.1 Section SYSTEMS Subject: WATER TREATMENT Feeding equipment and controller specifications for the condenser water and closed loop Are as follows: The control equipment for the condenser water will be of the type characterized as meterfeed, conductivity bleed, lock out on biocide addition. Chemical feed based on system bleed is only acceptable through the use of a conductivity controller. Note: The components of this equipment are as following: Water meter on cooling tower make-up – The meter is to be installed in an appropriate location to prevent freezing. The meter controller is to incorporate circuitry designed to turn the chemical pump on and off for adjustable time periods in proportion to the make-up water volume. Conductivity sensor in the by-pass loop – The controller circuitry is to open a solenoid blowdown valve when the condenser water conductivity rises to an adjustable set point. The condenser cooling water system must be designed so that uncontrolled bleed does not occur. 5. Total Alkalinity and Hydroxide level Oxygen scavenger level Corrosion/deposit inhibitor level Condensate pH Chloride level (feedwater and boiler water) TDS (feedwater and boiler water) Hardness (feedwater) Conduct weekly analytical tests on the closed loop chilled water and heating hot water systems and adjust the water chemistry accordingly. The tests is to determine the concentration of corrosion inhibitors. The results of all the above tests and chemical adjustments made are to be entered in a chemical log specifically designed for the purpose. The log sheets are to be supplied by the water treatment service company. Recommendations by the water treatment service company are to be implemented and compiled with. Copies of all reports developed by the water treatment service company are to be maintained in department files.

of 5 Number: 3.1 Section SYSTEMS Subject: WATER TREATMENT Feeding equipment for the steam boilers are as follows: Chemical feed is to be automated, with separate feed pumps and solution tanks for each chemical formula. The pumps are to be activated in conjunction with the feed water pump in order to maintain desired chemical levels in the water. Chemicals are to be fed either into the feed water tank below the water line or directly into the boiler. A stainless steel quill will be used for each chemical injection point. If fed to the feed water tanks, maximum protection is assured for pre-boiler and steam condensate lines. 6. Seven or fourteen day timer – Circuitry within the timer is to provide outlets for two chemical pumps. The date, time of day and length of pumping time are to be adjustable. The timer is to be equipped with a flip-top relay or solid state programmable circuitry so that the pumps will automatically alternate throughout the timer cycle. Circuitry is to be provided to lock out the blowdown solenoid during, and for an adjustable time period following, biocide addition. Controller sensor – Provision is to be made in the controller to sense when the condenser water pumps are not operating. This may be accomplished with the cooling tower recirculating pumps using a flow sensor or wiring the controller across the pumps. During shut down periods, no chemicals will be fed or blowdown permitted. Control equipment – The equipment may be composed of a single integrated unit or separately supplied components so long as the individual components integrate smoothly. Suitable equipments is available from: Autotrol Corp., Milwaukie, Wisconsin Lakewood Instruments, Inc.Compton, CA Moor Control, Inc., Muskogee, Oklahoma and others. Three chemical pumps are to be in-stalled. The pumps will be of the electronic diaphragm type. The maximum output rate is to be specified by the water treatment service company. The pumps are to be capable of pumping against a head one and one-half times the anticipated pressure at the point of injection. The chemical pumps may discharge either into the cooling tower basin or into the system piping. If injection is made into system piping, removable stainless steel injection quills (corporation stops) are to be installed. A solenoid blowdown valve and throttling valve are to be Installed on the hot water return to the tower side of the condensers. By-pass pot feeders are to be installed across the piping of the hot water boiler feed and chilled water pumps. The pot feeders are to be ASME tested and have at least 10 liters capacity and have a pressure rating two times the anticipated system pressure at the point of injection.

of 5 Number: 3.1 Section SYSTEMS Subject: WATER TREATMENT Storage, handling and disposal of chemicals is subject to environmental health protective measures, including secondary containment. Ensure that chemicals stored within the same containment area are compatible with each other. Review MSDS. 9. It Is recommended that corrosion coupons be installed in the condenser water system. This will help verify the effectiveness of the water treatment program in preventing corrosion. Most water treatment service companies will provide this service, installation and testing. 8. Continuous on demand eye wash stations must be installed in the vicinity of chemical feed equipment. 10. A drum disposal plan is to be provided by the chemical service company, or a mini-porta feed system installed (disposable drums are not used). 11. Periodic boiler blowdown is required for control of chemical levels and elimination of contaminates. Phosphate based corrosion and deposit inhibitors precipitate contaminates out of solution. This necessitates blowdown from the bottom of the boiler. The frequency of blowdown is determined by testing the chloride level of the feed water. This indicates boiler water cycles of concentration. Automatic blowdown equipment is not to be used for bottom level boiler blowdown. Polymer based corrosion and deposit inhibitors maintain contaminates in solution. Blowdown is determined by TDS (Total Dissolved Solids) levels. Automatic surface skimmer controller may be used for surface level blowdown. 7.

Surfaces, decks and adjacent areas are to be thoroughly cleaned and sanitized as frequently as conditions require. 5. Environmental health protective measures are to be maintained for the storage and use of chemicals. 6. Operating log sheets are to be maintained. 4. The filtration systems are to be operated and maintained in accordance with manufacturer’s recommendations. 3. The recommended levels of chlorine, pH, alkalinity, and hardness are to be maintained. 2. Accurate chemical tests are to be conducted and chemicals adjusted accordingly on pools and spas. 1. STANDARDS: The following is a description of the water properties controlled: FIRE CHLORINE – Free chlorine is the most effective bactericide form of chlorine. Its presence provides the immediate kill properties for destroying bacteria and algae on contact. TOTAL CHLORINE – Total chlorine is the measure of the Free chlorine plus the amount of chlorine in the water that has already combined with materials dissolved, or already in suspension in the water. As a bactericide it is not as effective as Free chlorine. 2. It is important that accurate pool an spa water chemical tests are conducted and the chemicals adjusted accordingly to ensure sparkling clean water, protection of equipment from the corrosion and scale deposits. The test are to be conducted (at a minimum) in accordance with governing codes. 1. PROCEDURE The Chief Engineer is to implement and monitor the Pool and Spa Treatment Program in accordance with industry standards, governing codes, and good operating practices. POLICY: To protect against corrosion, scale build-up and microbiological growth in the mechanical systems and provide guests with safe sparkling clear water. PURPOSE: Section: SYSTEMS POOL & SPA TREATMENT Subject: PROPERTY OPERATIONS POLICIES AND PROCEDURES

of 5 Number: 3.2 Section SYSTEMS Subject: POOL & SPA TREATMENT The best source for information on the operation and maintenance of the pool and spa equipment is the literature from the manufacturer. General requirements as follows: PUMP – Operate the pump enough hours each day to maintain clean water. Check and clean hair/link basket at least daily. The pump should be capable of recirculating the entire volume in six (6) hours for pools and four (4) hours for spas. 4. The following chemical ranges are guide-lines. Local codes will dictate specific chemical ranges to be maintained. SWIMMING POOLS Free Chlorine – 0.6 – 1.0 PPM Total Chlorine – 1.0 – 2.0 PPM pH – 7.2 – 7.6 PPM Alkalinity – 100 – 150 PPM Hardness – 200-250 PPM with a pH less than 8.0 SPAS Free Chlorine – 3.0 – 5.0 PPM Total Chlorine – as low as possible, always less than half of the free chlorine concentration, pH – 7.4 – 7.8 Alkalinity – 120 – 150 PPM 3. pH (PHENOL RED TEST) – pH factor indicates the acid or alkaline nature of the water. Sterilization of pool water is most effectively carried out in slightly alkaline conditions. Acid water is corrosive and also allows the chlorine to pass off in the form of a gas. Highly alkaline water retards the effectiveness of the chlorine that may be present. Phenol Red is the most accurate indicator. ALKALINITY – alkalinity has a substantial effect on balancing the pH of water, If the alkalinity is too low, the pH will rise and fall erratically. High alkalinity levels cause high pH values which reduces the effectiveness chlorine has a sanitizer. HARDNESS – The water hardness test includes a measurement of the magnesium and calcium present. These materials, in combination with carbonate, form scale. These deposits (sometimes referred to as calcium deposits) will form at the air-water sidewall line as evaporation takes place. In the presence of high pH (greater than 8.0), these deposits will form inside piping and fittings. They will restrict water flow, the mechanical operation of flow-meters, injectors, etc., and will adversely affect the operation of water heaters. In time, these deposits will cause metal surfaces to corrode beyond repair.

of 5 Number: 3.2 Section SYSTEMS Subject: POOL & SPA TREATMENT FILTER – Backwash or clean filter periodically. Check manufacturer’s manual for frequency and/or pressure gauge readings. Do not allow water discharged from filter to come in contact with lawn or shrubbery; chemicals in the water may kill plant life. HEATER – Have the heater and controls checked by a service company, or qualified staff members, each year for proper operation. For lighting of the pilot light and/or making adjustments, follow all directions printed inside the heater cabinet. AUTOMATIC CHLORINATOR – Use only the type of chlorine product recommended by the manufacturer, or professional distributor. Never mix different types of chemical compounds; serious injury may result. Chlorine gas is not to be used. AUTOMATIC POOL CLEANER – Operate for the amount of time recommended by the manufacturer. Most units are deigned to operate only when the filtration system is running. Clean strainers as necessary. LADDER/HANDRAILS – Check all bolts and tighten regularly. SKIMMER BASKETS – Check daily and clean when required to allow maximum skimming action and water circulation. CLEANING EQUIPMENT – Plastic cleaning equipment will last longer if stored out of direct sunlight. Keep telescopic poles, brushes and leaf nets away from deck to avoid tripping over them. WINTER COVERS./SOLAR BLANKETS – Clean prior to folding and storing to protect against odours, mildew stain and sticking. GASKETS AND O-RINGS – Lubricate with a special lube available from dealer. Do not use petroleum-based greases. TEST KIT – Store in a cool, dark place away from chemicals and heaters, Rinse test chambers after each use. Always use fresh reagents at the start of each season. EQUIPMENT WINTERIZING – Where freeze conditions exist, refer to manufacturer or dealer for protection of all equipment.

of 5 Number: 3.2 Section SYSTEMS Subject: POOL & SPA TREATMENT Due to the inherent design and purpose of spas, water conditions and quality are critical. The small volume of water, high water turnover rate, high temperature, water agitation and high bather load, contribute to rapid depletion of disinfectant and pH levels. Therefore, frequent testing and/or use of continuous reading device are recommended. 7. The frequency of cleaning, brushing, vacuuming and sanitizing of the equipment and deck areas should be determined based on the number of users. Heavily used facilities may have to be cleaned every 24 hours, preferably at night or during off hours. When using chemical compounds for cleaning purposes, the manufacturer’s safety recommendations must be observed. 8. Storage of pool chemicals is subject to environmental health protective measures, including secondary containment and chemical compatibility a per MSDS. In most cases, a continuous on-demand eye wash station is required in the pool equipment room. 9. The swimming pool and spa operating log is to be completed daily (minimum). 6. A swimming pool and spa operating log is to be used to record water chemistry test results, backwash, water clarity, temperature and other operations. This log is important documentation which can be useful if problems arise. Refer to Figure 1 for an example swimming pool and spa log sheet which can be modified to suit your needs 5.

FIGURE 1. – SWIMMING POOL LOG SHEET EXAMPLE Page 5 of 5 Number: 3.2 Section SYSTEMS Subject: POOL & SPA TREATMENT VAC. TEMP. CLARITY NO YES HARDNESS pH ALK TOTAL FREE DATE POOL WATER BACKWASH TOTAL CHLORINE

Frequency of chemical testing is to be established based on size and location of the fountain. Outdoor systems will require more frequent testing and treatment, due to the effect of the sun, atmospheric conditions and geographical locations. 2. The following chemical ranges are to be maintained: Free Chlorine – 0.6 to 1.0 PPM Total Chlorine – 1.0 to 2.0 PPM pH factor – 7.2 to 7.6 Alkalinity – 100 to 150 PPM Hardness – 200 PPM 3. Water Fountains are to be drained, cleaned, refilled and chemically charged as frequently as operating conditions require. 4. The water fountain mechanical equipment is to be maintained per the manufacturer’s recommendations. 5. Hard water spots on the water fountain surfaces and adjacent areas are to be removed as conditions require. 6. While fountains do not present the health hazards associated with swimming pools and spas, proper levels of pH and chlorine must be maintained for purposes of algae control and water clarity. 4. Fountain surfaces and adjacent areas are to be cleaned as frequently as conditions require. 3. Water and filter systems are to be maintained and operated according to the manufacturer’s instructions and industry standards. 2. A visual inspection of the fountain (s) is to be made daily . 1. STANDARDS: Due to the variety of fountain designs and operating conditions, additional procedures may be necessary to assure a clean and attractive setting. 7. The water fountains are to be visually inspected daily for water clarity and condition of the mechanical equipment. It is recommended that inspections be scheduled as part of morning rounds. 1. PROCEDURE The Chief Engineer is to implement and monitor the Fountain Treatment System in accordance with these procedures. POLICY: To protect against corrosion, scale build-up and harmful microbiological growth in outdoor and indoor fountains. PURPOSE: Section: SYSTEMS WATER FOUNTAIN TREATMENT Subject: PROPERTY OPERATIONS POLICIES AND PROCEDURES

No master key will be issued without written authorization from both the General Manager and Chief Engineer. All other keys are to be approved by the respective department head. 4. Purchase a key cabinet for storage of the original key file inventory. The capacity of the key cabinet should be determined by counting the individual coded keys, either from the bitting list or the finish hardware schedule. The cabinet should have the ability to be expanded by additional panels, if required. The key cabinet is to be locked when not in use. 2. Follow manufacturer’s instructions to establish the key file inventory system needed to control keys. 3. Review the bitting list and finish hardware schedule thoroughly. Use the architectural plans as a guide to verify location and identification of keys to ensure correct match-up with locksets. 4. All duplication keys are to be identified by stamping with the corresponding alphabetical letter and numbers assigned to it by the bitting identify any duplicated key. 5. Develop a key issue file system by department using 75 mm x 125 mm index cards for each department, as in Figure 1. A key issue card is to be kept on file for each key issued. 6. Keys are hotel property and must be returned to the Chief Engineer upon termination of employment. 5. Audits of master keys are to be conducted semi-annually. 3. A key issue file system is to be established and maintained. 2. A secure area for storage of keys and record will be provided and a file inventory of original keys is to be maintained. 1. STANDARDS: Establish a secure area in the maintenance shop for key storage and records. A designated key room is ideal. If this is not possible, the Engineering office area will be acceptable. The key storage area is to have limited access and kept locked when not in use. 1. PROCEDURE The Chief Engineer is responsible for monitoring the inventory and insurance of hard keys. Approval must be obtained from the Divisional Director of Operations for any other employees to monitor this system. POLICY: To safeguard the integrity of the hard-key system. PURPOSE: Section: SYSTEMS KEY CONTROL Subject: PROPERTY OPERATIONS POLICIES AND PROCEDURES

of 4 Number: 3.5 Section SYSTEMS Subject: KEY CONTROL An adequate supply of key blanks is to be maintained and kept secured. 9. All keys remain hotel properties and must be returned to the Chief Engineer upon employment termination. It is the responsibility of the employee and the Personnel Department to ensure that the key is accounted for and acknowledge by a receipt from the Chief Engineer. 10. If the department has a personal computer or access to one, the key issue file system can be computerized, eliminating the need for the manual index cards. 11. Keys will be issued to employees with written authorization via the Key Request form only, as in Figure 2 . Master key require approval by the General Manager and Chief Engineer . All other keys issued must be approved by the respective department head. 8. A semi-annual audit of all master keys is to be conducted by the Chief Engineer, using the fire index. The purpose of this audit is to account for all master keys and to verify that each master key is in the possession of the person issued the key. Any discrepancy found is to be noted on the respective file card and reported to the General Manager. 7.

Figure . – KEY ISSUES FILE CARD EXAMPLE ___________________________________________________________________________________________________________________ Name: ________________________________________________________________ Key #: _______________________________________ Department: ________________________________________________________________________________________________________ Position: _________________________________________________________________________________________________________ Signature: __________________________________________________________________________________________________________ Date Issued: ________________________________________________________________________________________________________ Date Audited: _______________________________________________________________________________________________________ Date Returned: ______________________________________________________________________________________________________ Where key will be kept: ________________________________________________________________________________________________ What keys fits : ______________________________________________________________________________________________________ Comments : ________________________________________________________________________________________________________ _____________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________ Page 3 of 4 Number: 3.5 Section SYSTEMS Subject: KEY CONTROL

Figure 2. KEY REQUEST FORM _____________________________________________________________________________________________________________________________ STARWOOD HOTELS & RESORTS KEY REQUEST Date _________________________________ Requestor ______________________________________________________________________________________________________ Department _____________________________________________________________________________________________________ Key Requested __________________________________________________________________________________________________ Reason for Request ______________________________________________________________________________________________ _______________________________________________________________________________________________________________ ________________________________________________________________________________________________________________ REQUIRED APPROVAL SIGNATURES General Manager ________________________________________________________________________________________________ Chief Engineer __________________________________________________________________________________________________ Department Head ________________________________________________________________________________________________ I, The undersigned receiver of above requested key, understand that loss of such key must be reported immediately to the Chief Engineer, and to my department head. Further understand I must return such key to the Chief Engineer upon my termination or upon request of the Chief Engineer. Key No. ____________________________Received on _________________________________________________________________ By ____________________________________________________________________________________________________________ Witness ______________________________________________________ Date _____________________________________________ Key No. ______________________________ Returned on _______________________________________________________________ by ____________________________________________________________________________________________________________ WHITE COPY – ENGINEERING DEPARTMENT YELLOW COPY - PERSONNEL Page 4 of 4 Number: 3.5 Section SYSTEMS Subject: KEY CONTROL

Obtain sterilized sampling bottles for dispatching samples of treated water system via courier to the testing laboratory. 2. Obtain and file test results for future reference. 3. Take the necessary action to sterilize any treated system where Legionella is detected, and resubmit samples for further testing. 4. Forward copy of test results top Divisional Engineer. 5. Identify a suitably qualified laboratory able to conduct tests for Legionella bacteria. 1. PROCEDURE The Chief Engineer will have tests conducted for the presence of Legionella Pneumophila bacteria on all exposed water system, such as cooling towers, domestic hot water systems, whirlpools/spas, QUARTERLY. POLICY: To reduce the risk of contamination of air and water systems. PURPOSE: Section: SYSTEMS LEGIONELLA PNEUMOPHILA BACTERIA Subject: PROPERTY OPERATIONS POLICIES AND PROCEDURES

4.0 GENERAL 4.1 Tools & Equipment 4.2 Building Documents 4.4 Service Contracts 4.5 Department Rules 4.6 Air Conditioning Standards 4.7 Basics of Psychrometrics 4.8 Additional standards

Each department member is responsible for replacement of any personal hand tool that is lost or damaged due to misuse or neglect. 5. Tools and equipment are to be inventoried, stored and controlled as detailed in the procedure. 4. Tools and equipment are to be commercial grade , have hotel identification markings and be maintained in good working condition. 3. The required hand tool list will be maintained and carried by each maintenance person. 2. The recommended tools and equipment list will be used as a guideline for the purchase of tools. 1. STANDARDS: Each department member is to provide, or be provided with, the required personal hand tools as listed in Figure 2 . The decision to provide the tools or have each member purchase their own is to be determined by each hotel. 2. A list of personal hand tools provided is to be maintained on file and each department member is to sign for all tools received. 3. Each member of the Engineering Department is to carry his/her personal hand tools (excluding trades such as painters) in a tool pouch during working hours. 4. Personal hand tools are to be replaced by the hotel f they are damaged or broken in the normal course of work. This will be determined by the Chief Engineer. 6. The tool and equipment list, as in Figure 1, is to be used as a guideline only to establish the type of tools and equipment required. Additional tools may be required or some of the tools not required; depending on the number of employees, their skill level and type of hotel. Quantities will be determined by the size of the hotel, number of employees and their skill level. 1. PROCEDURE The Chief Engineer is to purchase the recommended tools and equipment ensure that they are distributed, maintained and inventoried. POLICY: To standardize and control the Engineering Department tools and equipment. PURPOSE: Section: GENERAL TOOLS & EQUIPMENT Subject: PROPERTY OPERATIONS POLICIES AND PROCEDURES

of 9 Number: 4.1 Section GENERAL Subject: TOOLS AND EQUIPMENT The Engineering Department tools will be used by department members only . They are not to be loaned to other hotel employees. 11. N order to prevent theft, both tools and equipment and personal hand tools are to be stored in a secure area when not in use. 9. No tool will be removed from the property without written authorization from the Chief Engineer. 10. All hand tools purchased by the hotel and issued to Department personnel are to be returned upon termination of employment. 12. A complete list of the Engineering Department tools and equipment is to be maintained in departmental files. A semi-annual tool and equipment inventory , including personal hand tools, is to be conducted by the Chief Engineer. 8. All tools and equipment to be commercial grade , have hotel identification markings and are to be maintained in good working order. This also applies to hand tools where department members are required to provide their own. It is recommended that each hand tool be marked with the individual’s initial. 7.

FIGURE 1. – TOOLS AND EQUIPMENT GUIDELINE MECHANICAL TOOLS AND EQUIPMENT Hand Operated oil pump Grease guns Oil cans Arc Welding machine, 225 amp. Protective welding screens Welding and cutting outfit (Porta-Weld) Torch assembly, hose, sparker, cylinder, oxy-acetylene, cutting, tip, regulator, welding tip Welding goggles Arc welding helmet and goggles Safety shields Disposable dusk masks Work gloves 150 mm plastic funnels 8 m extension ladder 5 m extension ladder 2, 5 m aluminum step ladder 2, 5 aluminum step ladder 1, 2 aluminum step ladder High-pressure washer, 1 ½ HP motor, 220 volts, maximum pressure – 50 bars at 106/min Heavy duty wet/dry vacuum, 100 tank with dolly, suction hose and heads Portable air compressor, ¾ HP motor, 8 bars, 10 m air hose with quick release nozzle Set of ex-out bearing pulling attachment Combination 3-prong bearing puller Set packing pullers Screw jacks 2 ton hydraulic service jack 1 ton chain lever pullers 1 ½ ton chain hoist (manual) Portable circulating pump 200 L. stand-up drum truck 200 L. drum stand with handles Drill press, ¾ chuck Bench grinder with wire wheels (heavy duty) 190 mm mechanic vise Tap and die set (3 – 18 mm) 7 drawer rolling tool cabinet with key lock Alignment mirrors, telescopic arm Rectangular inspection magnifier Magnehelix gauge dial Hand held velometer Orbital sander with assorted grade disks/brushes Screw extractor and drill set Multi-purpose utility shears (scissors) Oily waste cans, yellow Pair PVC coated shoulders length gloves Page 3 of 9 Number: 4.1 Section GENERAL Subject: TOOLS AND EQUIPMENT

Pair each – small, medium, large and extra large seamless PVC gloves, elbow length, chemical resistant ½” square driver socket sets, 37 pieces 3/8” square driver socket sets, 25 pieces ¼” square driver socket sets, 16 pieces 150 mm adjustable wrench (insulated handle) 250 mm adjustable wrench (insulated handle) 455 mm adjustable wrench (insulated handle) Sets open end box combination wrench, 8 – 30 mm (Service and Maintenance) 150 mm Rat Tail file with handle Trouble light, 20 m, 3 wire with ground plug, side and switch outlet 150 mm vise grip Center punch set, general purpose punch set General punch staple guns Boxes staples Maintenance leather tool pouches with belts Square point with turned step shovels Round point with turned step shovels 250 mm wire brushes (long handles) 420 mm hack saws (heavy duty) 300 mm hack saw blades Tite spot hack saw Adjustable handle hack saw Heavy duty hollow punch set Knock out punch set Vernier caliper with dial Single panel welding curtain Letter size clipboard Legal size clipboard Wheelbarrow Medium duty wood deck platform truck Steel hand trucks Steel drum dolly with 4 wheels Flammable liquid safety can Combination slip joint pliers, 65 mm, insulated Channellock pliers, 265 mm, insulated Pair chemical resistant knee high rubber boots Pair knee high rubber boots Click stop adjustable torque wrench Standard steel storage cabinets with locks, 90 x 45 x 180 cm Hercules steel storage cabinets with locks, 60 x 40 x 90 cm ELECTRICAL TOOLS AND EQUIPMENT Non-conducting step ladder Voltage tester Simpson variable volt/ohm meter. 5000 volts Amprobe, 1000 amps Fuse pullers, assorted sizes Switch box lock out Single keyed padlocks Page 4 of 9 Number: 4.1 Section GENERAL Subject: TOOLS AND EQUIPMENT

Electronic solder gun and solder Pair rubber lined lineman gloves Long nose pliers (insulated handles) 125 mm needle nose pliers (insulated handles) 150 mm side cutting pliers (insulated handles) Electrician pliers 10” (insulated handles) 300 mm blade screwdriver 250 mm blade screwdriver 150 mm blade screwdriver 150 mm philips screwdriver 125 mm philips screwdriver Electric wire splicing knife Sets robertson head screwdriver (black, green, red, yellow) Sets nut driver (graduated sizes 3-13 mm) Sets allen wrench (graduated sizes 1-17 mm) Light meter Set conduit bender 10 m u-ground extension cords Electric lamp tester Flashlights (waterproof) Insulated solderless terminal kit with Crimper/ cutter Completely made up temporary power distribution Panel, 50 amps, plug 3 m lead to panel with 20 Amp circuit breakers and duplex plugs Wire pull spring PLUMBING TOOLS AND EQUIPMENT 150 mm pipe wrench 350 mm pipe wrench 700 mm pipe wrench 250 mm offset hex jaw pipe wrench 300 mm ( 10 – 50 mm) strap wrench Heavy duty chain wrench Faucet wrench Basin wrench Toilet augers Toilet plungers, heavy duty Heavy duty pipe vise, 150 mm Tripod for vise Pipe cutter Pipe reamer Power drain snake 20 mm x 20 m Pipe clamps, assorted sizes REFRIGERATION TOOLS AND EQUIPMENT Halide leak detector Dial-a-charge (freon) Page 5 of 9 Number: 4.1 Section GENERAL Subject: TOOLS AND EQUIPMENT

Vacuum analyzer Manifold Vacuum pump Refrigeration charger with gauges and hoses ¼” adapters with gasket (used from cylinder to manifold) Vacuum cleaner with blower (portable) Electronic digital thermometer Tube flaring and cutting kit Propane fired soldering kit with self-ignited torch Amprobe and voltage tester CARPENTRY SHOP TOOLS AND EQUIPMENT Table saw with assorted 250 mm blades Radial arm saw with assorted 10” blades Drill press, chuck and vise Drill stand 125 mm shop vise 10 mm roto hammer drill with assorted bit 15 mm roto hammer drill with assorted bits Jigsaw Belt sander with assorted grade belts Ram set concrete anchor gun Circular saw with assorted blades (portable) Saber saw scroll Router with assorted bits Rubber mallets 5 kg sledge hamemr 4,5 kg ballpen hammer 3,5 kg ballpen hammer Claw hammer 600 mm crow bars Claw bars 25 m tape measure 10 m tape measure Cold chisel Cape chisel Diamond Chisel Set wood chisel, assorted sizes Carpenter’s level (wood) Aluminum levels Torpedo levels, aluminum 24” bolt cutter 14” bolt cutter Heavy duty metal & wire shearing kit Compound action pipe and duct snips Pop rivet gun with assorted rivets 85 mm c-clamps 115 mm c-clamps 180 mm c-clamps “ H” wood clamps Page 6 of 9 Number: 4.1 Section GENERAL Subject: TOOLS AND EQUIPMENT

Electric hot glue gun and 100 glue sticks Variable speed Cordless drills and charger Electric miter box Sets drill bits for metal (3 x 17 mm) Sets drill bits for wood ( 5 – 20 mm) Sharpening stones Hatchet Hand ripsaw Hand Finish saw Key hole saw Coping saws, 2 packs blades Wood vise Expandable wood bits Combination square 250 mm wood rasp, fine 250 mm wood rasp, coarse Carpenter’s rule Glass cutter Nails sets (3 sizes) Workmates bench (black & decker type) Concrete drill bit set, 3 – 14 mm Economy carpenter tool apron Utility Knives with blades Heavy duty pencil grip etcher, electric Utility caulking guns Case 100% silicone rubber sealant Case fast seal tub and tile caulk Number punch set Lock picking kit High security padlock, separate keys 3/4 “ – 2 x 15/8 high security padlock, alike keys Hot galvanized long link steel chain PAINTERS TOOLS AND EQUIPMENT Airless paint sprayer Paint brushes 50 mm, 100 mm, 125 mm 200 mm roller & cover Roller pans Roller extensions Putty knives 50 mm, 100 mm, 125 mm Drop clothes Disposable dust masks Seam roller Razor knife Wallpaper smoother Square Paper masking machine Sanding pole 1,5 m ladder Page 7 of 9 Number: 4.1 Section GENERAL Subject: TOOLS AND EQUIPMENT

THE HOTEL SOURCE EQUIPMET Key cutting machine, domenion # 150 AM-MKII from Unican, North Carolina (919) 446-3321 Standard Starwood Hotels & Resorts ken fixit cart Standard Starwood Hotels & Resorts fire cart Standard Starwood Hotels & Resorts fire suitcase 60 gallon ul listed flammable storage cabinet Walkie Talkies Page 8 of 9 Number: 4.1 Section GENERAL Subject: TOOLS AND EQUIPMENT

FIGURE 2. – PERSONAL HAND TOOLS Tool pouch Tool pouch belt Work gloves Flashlights Pocket thermometer Utility knife (retractable) Torpedo level 125 mm slip joint 125 mm needle nose 250 mm channel lock 150 mm side cutters 250 mm adjustable wrench Volt – circuit tester 4 way screwdriver Hexwrench set 5 m tape 125 mm vise grips Lockout & padlock Page 9 of 9 Number: 4.1 Section GENERAL Subject: TOOLS AND EQUIPMENT

One (1) set of construction contract documents, consisting of the general contract/special conditions, contract plans and specifications, addendum clarifications, change orders and related revisions, and a list of all subcontractors, identified by trade, is to be maintained in the Chief Engineer’s office, or other secure location. 5. Equipment warranties will be submitted to manufacturers. 4. As-built blueprints will be kept current . 3. Only reproduced copies of building documents will be removed from the property. A log must be maintained for tracking the issuance of the documents. 2. A minimum of two (2) sets of as-built blueprints, two (2) sets of equipment manuals, and one (1) set of construction contract documents are to be maintained. 1. STANDARDS: A second working set as-built blue-prints is to be stored in the maintenance shop in a steel sectional file of adequate size to permit flat storage, 2. One (1) set of equipment manuals is to be maintained in the Chief Engineer’s office or other secure location. This set will be identified as the master set and must not leave the office, except for duplication . 3. A second working set of equipment manuals is to be maintained in the maintenance shop. 4. One (1) set of as-built blueprints must be maintained in a secure location, to be determined by the General Manager and the Chief Engineer. These blueprints are to be treated as legal documents with precautions taken to prevent damage from fire, water or theft. 1. PROCEDURE The Engineering Department will retain and safeguard copies of the building documents. POLICY: To ensure protection and control of the building design documents. PURPOSE: Section: GENERAL BUILDING DOCUMENTS Subject: PROPERTY OPERATIONS POLICIES AND PROCEDURES

of 3 Number: 4.2 Section GENERAL Subject: BUILDING DOCUMENTS Ensure that warranties for new equipment are completed and submitted to the manufacturer. A copy of all equipment warranties are to be maintained in department files. 10. A record of all building document transmittals, from an architect, engineer or contractor, will be maintained in the department files. 8. Blueprints are to be kept current. Modifications to mechanical, plumbing or electrical systems are to be incorporated into the working set of as-built. 9. A log is to be maintained for any reproduced building document removed from the property. The log will include the name of person/company, reason for removal, date removed and data returned, as in Figure 1. 7. Only reproduced copies of blueprints or equipment manuals may be removed from the property. Permission must be obtained from the Chief Engineers. 6.

FIGURE 1. – BUILDING DOCUMENT REQUEST LOG Page 3 of 3 Number: 4.2 Section GENERAL Subject: BUILDING DOCUMENTS DATE RETURNED DATE REMOVED REASON PERSON/ COMPANY

The Chief Engineer is to be involved in negotiation and renewal of all contracts expensed to the Engineering Department. 4. Service contacts are to be periodically analyzed to ensure conformance to the agreement and will be evaluated annually. 3. Service contracts to be obtained based on the recommendations specifically outlined. 2. The list of equipment, systems and services is to be used only as a guideline when determining which contracts may be required. 1. STANDARDS: Service contracts may be obtained for the following equipment, systems, or services and are to be expensed to Engineering Department. Elevators Chillers HVAC controls Televisions Hazardous waste removal Waste removal Pest Control Water treatment Exterior signs Point of sale system Property management system Kitchen exhaust duct cleaning/fireproofing Laundry exhaust duct cleaning Fire alarm detection system Diesel generator/fire pump 2. The accompanying list of equipment, systems and services is intended to be used as a guideline to determine what requires contracted labour. The majority of items should be contracted, others must be evaluated based on specific needs, such as the number of employees and skill requirements may vary depending on design, geographical location or local codes. 1. PROCEDURE Service Contracts may be obtained for work that is beyond the scope of knowledge, skill or staffing level of the Engineering Department. POLICY: To establish guidelines and specific recommendations for contracting outside services. PURPOSE: Section: GENERAL SERVICE CONTRACTORS Subject: PROPERTY OPERATIONS POLICIES AND PROCEDURES

of 3 Number: 4.4 Section GENERAL Subject: SERVICE CONTRACTS The three bid process must be used to obtain competitive pricing for service contracts. The low bid does not necessarily have to be accepted as long as the selection can be rationalized. 7. The Chief Engineer must be involved in negotiation and renewal of all service contracts expensed to the Engineering Department. 8. Each contract is to be analyzed periodically to ensure conformance to the agreement. 9. Invoices for each service contract must be obtained and approved for payment by the Chief Engineer. 10. A Starwood Hotels & Resorts Work Order Contract form must be used for all service contracts. 11. Each contract is to be reviewed annually for competitive price, continued need and necessary modifications. 12. A copy of all Engineering Department service contracts is to be maintained in the department files and considered a permanent record. 13. A record of all service contracts issued is to be maintained and updated as required, as in Figure 1. 14. Annual cost adjustment for service contracts which exceed one year, if applicable, should be based on reasonable price index, such as the Product Commodity Prices for Metals and Metal Products . 5. Non-performance or poor workmanship must be included as part of the contract termination clause. A written cancellation notice, 90 days prior to the contract anniversary date, must also be included. 6. Extended service dates (exceeding 3 yeas), for any service contract, should be scrutinized closely and inmost cases avoided . 4. Equipment service contracts are to include preventive maintenance, parts, labour and emergency call-backs (if deemed necessary)., exclusive of overtime and travel time. Service contracts which charge additional costs for parts and labour for repairs discovered during scheduled inspections should be avoided . 3.

FIGURE 1. – SERVICE CONTRACT RECORD EXAMPLE SERVICE CONTRACTS ISSUED Page 3 of 3 Number: 4.4 Section GENERAL Subject: SERVICE CONTRACTS TYPE OF SERVICE ANNUAL COST EXP. DATE DATE OF ISSUE COMPANY NAME

Each member of the Department will be required to sign a statement indicating that he/she has received and understands the Department Rules. 4. All rules will be distributed to and reviewed with each member of the engineering Department. 3. Departmental rules will be expanded to include any individual hotel requirements. 2. All Department rules are to be enforce. 1. STANDARDS: The following rules will be followed by all members of the Department and enforced by the Chief Engineer: The SGR program is an integral part of the Engineering Departmental philosophy and all members of the Department will conduct themselves accordingly. Each member of the Department will maintain the highest standards of personal hygiene and grooming. An approved, clean uniform will be worn while on duty. Approved, clean coveralls will be worn to protect uniforms When necessary, but avoided in guest contact areas. Name tags must be worn at all times while on duty. Baseball caps are considered inappropriate and will not be worn while on duty unless it is an approved cap worn by the Roads, Walks and Ground Department. Appropriate, publishable footwear will be worn at all times while on duty. Steel-toed shoes/boots are recommended. Sneakers or sandals are not permitted. 1. PROCEDURE The Chief engineer is to develop and enforce Department Rules in addition to and consistent with all existing Hotel Rules. POLICY: To establish and maintain Department rules designed to achieve a high level of job performance and safety from all Property Operations personnel. PURPOSE: Section: GENERAL DEPARTMENT RULES Subject: PROPERTY OPERATIONS POLICIES AND PROCEDURES

of 4 Number: 4.5 Section GENERAL Subject: DEPARTMENT RULES The Department will be expanded to include any individual hotel policies, local code requirements, union stipulations, etc. 2. Only hotel authorized emblems, buttons, etc. will be worn during working hours. Department members are expected to report for work on time. Irregular attendance or tardiness will not be tolerated. Time card procedures must be followed exactly as prescribed. Punching in or out for another employee will not be tolerated. The use of drugs or alcohol while on duty, or reporting for work under the influence of same, will not be tolerated and is grounds for immediate termination. Smoking is permitted in designated areas only. Chewing of tobacco or gum while on duty is prohibited. Except for the Ken Fixit mechanic, members of the Department will never enter an occupied guest room without valid and properly issued work ticket, or when dispatched to a guest room at the guest’s request, via inhouse communications. Practicing safe working habits and maintaining a safe work environment is the responsibility of each and every member of the Engineering Department. A full compliment of hand tools will be carried at all times while on duty. Starwood Hotels & Resorts Safety Tag/Lockout system will be observed at all times without exception . A work ticket will be completed for each job assignment. Attention will be paid to filling out work tickets completely, including an accurate assessment of time spent. All shop tools will be returned to their proper location in a clean, and workable condition. Each member of the Department will ensure that all work areas are clean at the end of their shift.

of 4 Number: 4.5 Section GENERAL Subject: DEPARTMENT RULES After a complete review of the rules, each employee will sign a statement attesting to their knowledge and understanding of the Department Rules. The signed statement is to be kept in the employee file. See Figure 1 for an example of a Department Rule Statement. 4. Failure of any member of the Department to follow the Department rules can result in disciplinary action, suspension or termination of employment. 5. Due to the sensitivity of disciplinary measures and regulations governing the termination of an employee, it is recommended that the hotel Director of Human Resources review and approve all Department Rules. 6. The Chief Engineer will review the Department rules with each member of the Department. 3.

FIGURE 1. – EMPLOYEE DEPARTMENT RULE STATEMENT EXAMPLE I have reviewed all Departmental rules with the Chief Engineer, I fully Understand the rules and will comply with them. I understand that violation of the Departmental Rules could result in disciplinary action, suspension and/or termination of employment, ___________________________ _____________ EMPLOYEE SIGNATURE DATE Page 4 of 4 Number: 4.5 Section GENERAL Subject: DEPARTMENT RULES

All thermostats which are located in accessible positions, except for guest rooms, will be made secure, to prohibit any adjustment by unauthorized staff or guest. 2. All guest room thermostats will be adjusted to the set point value each day (if necessary) by the room attendant. 3. Space temperatures and relative humidity (R.H.) will be measured and recorded each day in all major public areas, e.g. lobby, restaurants and function rooms. Accurate and reliable heavy duty measuring instruments, with a resolution of 0.1 o C, will be purchased. 4. Ventilation rates, or number of air charges per hour, will be strictly observed, as per design specifications (Good practice in the industry today accepts a median value of a 10 minute air change, eg. Six times per hour). The air balance of each space will be verified each year to ensure that it is in accordance with the original design criteria. 5. All associated controls will be accurately calibrated and tested on an annual basis. This must be part of a service contract for all the hotel’s control systems. 1. PROCEDURE Operating time schedule will be established for all conditioned and ventilated spaces, and controlled automatically, either by a computerized program or time clock. It is imperative that AU.H. s are started early enough to allow design conditions to be reached within the space. 6. The Chief Engineer will ensure that all air conditioned spaces in public and back of house areas are maintained within a fixed range of temperature and relative humidity at the following values: POLICY: To ensure that every hotel maintains environmental conditions within a range of comfort, whilst minimizing the costs of providing them. PURPOSE: Section: GENERAL AIR CONDITIONING Subject: PROPERTY OPERATIONS POLICIES AND PROCEDURES 45 %- 55 % 35 %-45 % 23 +/- 1.0 D.B. 21 +/- 1.0 D.B. Summer Winter R.H. Temperature o C

of 3 Number: 4.6 Section GENERAL Subject: AIR CONDITIONING Air conditioning is defined as the simultaneously control of temperature, humidity, air movement and the quality of air in a space. The aggregate effect of these factors has been combined into a concept called the “Comfort Zone”, under which the majority of people will feel comfortable. Comfort can be defined as any condition that when changed, will make a person uncomfortable. A guest’s opinion of a hotel is extremely dependent on the condition of the thermal environment. If he is comfortable, then he enjoys the attractions and amenities of the hotel. However, if he feels uncomfortable, then he usually focuses on the negative sensations and does not notice the positive attributes of the hotel. Comfort conditions are based upon people being normally clothed for indoor living; engaged in only light activities such as reading, office work or occasional walking about the room; with an air velocity of 4.5 – 7.5 meters per minute; and with no radiation effects. Relative humidity is often more difficult to control than dry-bulb (D.B.) temperature. Therefore, it must be remembered that as R.H. increases, temperature can be decreased and conversely as R.H. decreases, temperature can be increased. As a general guide, for every 10% change in R.H. the temperature can be adjusted by 0.5 o C. R.H. above 70% and below 30% will not provide comfort conditions, regardless of the D.B. temperature. Frequently, after determining what is desirable, it has to be determined what is possible, and then by compromise, bring the two as close together as possible. RATIONALE: The Chief Engineer will prepare a written policy and instructions to all management on the establishment of a fixed range of conditions of temperature and R.H. that will be maintained within the hotel. (See Sample) 8. All A.H.U.s, and associated equipment will be properly maintained as per manufacturers recommendations, to ensure optimum performance at all times. 7.

SAMPLE MEMORANDUM To: All Department Heads & Supervisors From: Chief Engineer Date: Subject: AIR-CONDITIONING The thermal conditions within all public and back of house areas in this hotel will be maintained between 21 o C – 23 o C during winter and 23 o C – 24 o C during summer at 45%/55% relative humidity. Under no circumstances will these parameters be changed at the whim of any staff member, or to satisfy as single guest’s complaint. These conditions are designed to satisfy the majority of people at all times. All occupied spaces are monitored for compliance with the above conditions on a continuous basis, but if you are continually feeling uncomfortable, please seek technical assistance. Page 3 of 3 Number: 4.6 Section GENERAL Subject: AIR CONDITIONING

Additional standards Part - 5

5 Additional standards 5.1 Third party testing of critical equipment 5.2 Engineering contract 5.3 Contract workers on premises 5.4 Shower head maintenance 5.5 Pulsating shower head 5.6 Lint cleaning standards 5.7 Fire alarm emergency procedure 5.8 Infra red survey 5.9 Kitchen extract duct / duct cleaning

5.1 Policy Number: Effective Date: Procedure: List of Critical Equipment / machineries i. Elevators : Annual Certification ii. Boilers : Annual Certification iii. Pressure vessels : Annual Certification iv. Thermographic : Annual Certification v. Duct Condition : Every Three years Certification vi. Building Structural : Every Five years Certification B. Director of Engineering must maintain documented records of all critical equipment/ machineries including date of spare part replacement and preventive maintenance date, etc. C. Not less than every twelve (12) months or as indicated above, a qualified survey firm is invited to test and certify that said critical equipment/machineries is serviced and operational suitable. D. The cost of such test and certification is a hotel property maintenance expense, which should be projected, in the hotel’s annual operating plan. E. Name of firm: Lloyds or a reputable local certified firm. Deviation: Requires written approval from the RVP It is Starwood Hotels and Resorts policy that routine preventive maintenance is carried out on all M & E equipment. However, it is the divisional policy that third party testing/certification is carried out on a regular basis on critical plant room equipment/machineries. Objective: Approved by: Title Page 1 of 1__ Superceding Policy: ENG 001 THIRD PARTY TESTING OF CRITICAL PLANT ROOM EQUIPMENT/MACHINERIES Subject

5.2 Policy Number: Effective Date: Procedure: (Contract document) The Work Order Contract is a legal document stipulating the contractual obligations between the hotel and the contractor, which should include not less than the following clause: Parties, date and other general information. Full description of the scope of work, materials and labour Obligation of hotel and third party Completion date and delay penalties. Insurance coverage, Hold Harmless Clause and Security aspects. Payment schedule and retention value. Deviation: Requires written approval from the RVP It is a divisional policy that any third party engagement for Engineering Projects/Works at the hotel premises is confirmed by a written work order contract, which in general is more elaborated than a standard purchase order. Objective: Approved by: Title Page 1 of 1__ Superceding Policy: ENG 002 ENGINEERING CONTRACT Subject STANDARDS

5.3 Responsibilities of General Manager Prior to the arrival on site of any contractors to carry out any work within the hotel or its grounds, they should: Inform all relevant hotel staff that works are to commence, and as to the location and nature of such works, and to have regard to such works in the carrying out of their duties during the period of such works. Ensure that all necessary steps are taken to inform guests, whether resident or otherwise, of the presence of the works. In the appropriate cases they should ensure that notices are provided in appropriate locations indicating the carrying out of the works. Responsibilities of Director of Engineering It is the responsibility of the Director of Engineering to taker all necessary steps to arrange for the orderly admission to the hotel site of contractors to carry out their operations and to inform them all procedures within the hotel relevant to the carrying out their work. He should:- 1.Advise the contractor of the hotels emergency procedures including the indication of the fire assembly points and evacuation procedures. Deviation: Requires written approval from the RVP It is a divisional policy that any third party conducting work at the hotel is supervised by the hotel Engineering and Security Departments. Objective: Approved by: Title Page 1 of 4__ Superceding Policy: Policy Number: ENG 003 Effective CONTRACTORS WORK ON PREMISES Subject

5.3 CONTRACTOR WORK ON PREMISES Page 2__________________ Advise the contractor of the general use of the area within the works are taking place and of the presence of movements of any large groups of people present in the hotel during the carrying of the work. Ensure that the contractor complies with his obligations in connection with screening of the work from the other users of the hotel. Ensure that the contractor removes any debris and waste materials from the site and that in the absence of workmen from the works that they are left in a protected, tidy and safe condition. Make the contractor aware of the presence of any water, gas or electricity services, machinery, pipes, wires and cables in the vicinity of the works and of any particular dangers which they may pose in the carrying out of the work. Ensure that any incident on the site involving anybody other that the workmen themselves is reported to the appropriate authorities. In the event of accidents, to the workmen on site of which the management is aware, to request the contractor to make the appropriate report in relation to this. I. Procedure: (General) A contract must be in placed authorizing work/project stipulating all aspects (see Engineering contract policy) A written document with workers name side of work, etc. is issued to the Security Department so that temporary name badges and time card are made and issued. II. Procedure: (Hot Work) The following procedures will be adhered to regarding issuance of Hot Work Permit. Issuing of Permits Permits for cutting, welding, brazing, pipe, sweating and the like procedures, shall be issued by the Director of Engineering or designate. Permits shall be valid only for the date of which they are issued. B. Responsibility of Permit Issuing Department A preliminary inspection of the area where the work will be conducted shall be performed by the responsible authority to determine what safety precautions will be required prior to issuing the permit. Inspect the operation site immediately prior to the operation to ensure that all of the following are complied with:

5.3 CONTRACTOR WORK ON PREMISES Page 3__________________ a. If possible, move the object being worked on to a location where there are no combustible (outside the building if possible). If the object cannot be moved, remove all combustible within a 10 meter radius, where a 10 meter radius clear area is not possible, clear as much as possible and cover remaining combustibles with fire resistant covers or shield with metal fire proof guards/curtains. Edges of covers at the floor shall be tight to prevent the passage of sparks underneath. b. Cover walls or floor openings to prevent the passage of sparks. c. Cover or shut down ducts that might carry sparks to combustibles. d. Where open flame work is taking place, sprinkler and detection systems shall be fully operational (unless the work is being conducted on either of these systems). Where the systems are impaired, security checks must be conducted on a regular basis. e. Show the person doing the work where the fire hose is located and verify that they and the person on fire watch know-how to operate the fire hose. f. Show the person doing the work and the person on fire watch where the nearest fire alarm station (manual pull) is located. Verify the type know how to activate the alarm. g. Verify that the person doing the fire watch is equipped with a fully charged minimum 5KG, ABC extinguisher. C. Contractor Responsibility Must obtain a permit before starting any open flame work. Must provide a minimum 5 kg, fully charged ABC extinguisher. Must provide a means for shielding combustibles from parks when necessary. Must provide a person in addition to the performing the work for fire watch. Contractor must stop work if the original conditions in the area where the work is being done, changed. Must verify that equipment for open flame work is in satisfactory operating conditions. Must either post the permit in the area where the work is being done or be able to produce it on demand. D. Responsibility of the Fire Watcher Must know how to use a portable fire extinguisher. Must know the locations of the fire alarm station and the fire hose. Verifies that the work area is clear of all combustibles, so that they are adequately protected. Maintains a steady and uninterrupted watch to ensure that any fires are detected early on.

5.3 Page 4__________________ 5. Continues the fire watch for at least a half hour after completion of the work to ensure the detection of any smoldering fires. Suspension of Work 1. A security officer is to conduct spot checks of every permitted open flame work site. 2. Where operations are not in compliance with the above requirements, the security officer staff immediately stop the work. 3. The fire watcher is to stay at the site for at least half an hour after the work has been stopped. 4. The security officer may allow the work to resume if he/she determines that all safeguards have been put in place.

5.4 Policy Number: Effective Date: Deviation: Requires written approval from the RVP Procedures: Open and descale the showerheads minimum two times a year, apart from Ken Fixit program. Descaling should be carried out using chemicals recommended by the suppliers e.g. Grohclean Is ideal for all GROHE fittings. Adequate stock of spare parts should be maintained i.e. Repair Kit/O-rings, gaskets, nozzles etc. Recommended tools by the manufacturers should be available with the plumbers. To provide guests with clean and hygienic showerheads with optimum pressure and variable flows as per design specification. Objective: Approved by: Title Superseding Policy ENG 00 SHOWERHEAD MAINTENANCE Subject

5.5 Policy Number: Effective Date: Procedures: Should have an outer control bezel to set the intensity of water spray in any of 3 positions: 1a. Concentrated full shower spray that cleanses and refreshens. 2b. A gentle but invigorating massage to ease stress and tension plus a soothing spray to rinse and refresh. 2c. A brisk, stimulating massage to work out after-exercise soreness and specific tension spots. All flow regulator device must comply with mandatory water conservation measures. A rubber filter screen has to be placed inside the pivot ball joint and should be cleaned at least once a year or whenever you notice a drop in water pressure. Ideal showerhead should consist of water saving restrictor, chrome plated base cone, exit plates create multiple spray patterns, inner power chamber directs water to spray plates, outer power chamber channels water flow to turbine, high speed turbine creates pulsating action, outer control bezel selects shower modes, and front spray cup creates wide-pattern full spray shower. To provide guests with clean and hygienic shower massage – pulsating showerhead as per designed specification. Objective: Approved by: Title Superseding Policy PULSATING SHOWERHEAD Subject

5.5 Deviations: Requires written approval from the RVP Brands recommended: Grohe and Speakman

5.6 Policy Number: Effective Date: Procedures: Daily Cleaning of accumulated lint from inside of all equipment. Cleaning of accumulated lint from the outside of equipment, ducts and surrounding areas. It is mandatory for Lint Collecting Equipment: Empty the lint bag of lint collector (filter) regularly. This should be done once the bag is three quarters full. This has to be inspected daily by the Laundry Department, a report to be forwarded to the Engineering. Monthly Clean the filter with spray nozzle or flushing with water. Hose down the interior of the lint collector. Quarterly Check the exhaust fan for any build up of lint or other foreign particles. Internal cleaning of the duct. Objective: To eliminate the accumulation of dry, highly combustible lint on laundry machines and extract ducts. Approved by: Title Superseding Policy LAUNDRY LINT CLEANING Subject

5.6 Deviations: Requires written approval from the RVP. 4. Annual Cleaning Inspection and cleaning of the vertical and horizontal risers to be carried out.

5.7 Procedures: Please see attached Policy Number: Effective Date: Deviations: Requires written approval from the RVP Objective: To serve as guidelines in ensuring proper Fire Alarm and Emergency procedures are adhered to. Approved by: Title Superseding Policy FIRE ALARM & EMERGENCY PROCEDURES Subject

5.8 Procedures: To be carried out and on peak times. Contract the internationally recognized thermographic consultant with the latest imaging thermographic camera Carry out thermographic imaging on all electrical equipment. Record all imaging Carry out at least once a year Send report to Area Director of Engineering Refer – Annex I for conclusion of report. Policy Number: Effective Date: Deviations: Requires written approval from the RVP Objective: To know and prevent well in advance any overheating of cables/bus, bar/wire termination/bearing ends/bearing journal/any moving parts and other electrical and mechanical installation. To know of any points eventually which can cause short circuiting/fire/damage/breakdown. The survey is used for predictive maintenance saving down time and improving operating profits. Approved by: Title Superseding Policy INFRA RED THERMOGRAPHIC SURVEY Subject

5.8 Tel/Fax: 044-1604-770030 Fax: 049(0) 821717325 England Tel: 049(0) 8212720-122 Northants NN6 8BX Germany East Haddon D-86165 Ausburg Tilbury Road Bluechestrasse 1 Haddon Fields M/s Institute of Technical Expert Opinion Bluechestrasse1 M/s Thermographic Services Ltd. Recommended:

ANNEX I Thermographic Survey Assessment of Seriousness As a general rule for determining the condition of electrical equipment, any component which is 5 o C or more warmer than adjacent components is considered as needing attention. The larger the temperature difference, the more serious the problem. In most cases the load on the equipment is not exactly known and different loads may account for smaller temperature differences. The following tables give a brief on temperature differentials and their required actions. Low Voltage Systems High Voltage Systems These are temperature rises above ambient or above another similar component. In most cases, absolute temperatures are not so important as they will depend upon ambient temperatures. The expected ambient temperatures should be taken into account when specifying these components. Note that Infra-red scanning can be inspected only with sufficient or maximum loads. Even serious faults cannot be detected if there is little or no current flowing. Motors also should be included in the Infra-red scanning inspection. Maximum heat generation takes place in the windings. As a general rule, the temperature on winding should not be more than 40 o C above ambient. Bearing housing which is warmer than the motor body is also considered to be an anomaly. The larger the difference the more serious the problem. 5.8 D Repair immediately Over 30 o C C Repair as soon as possible 20 o to 30 o C B Priority repair schedule 10 o to 20 o C A Repair as scheduling permits 0 oo TO 10 o C LEVEL ACTION TEMPERATURE Repair Immediately 50 o to 75 o C Repair within 30 days 30 o to 50 o C Repair as scheduling permits Under 30 o C ACTION TEMPERATURE RISE

5.9 Procedures: Daily Filters to be removed, degreased and cleaned. Hoods and the grease trap to be cleaned. Weekly The Stewarding Department to prepare a checklist to be issued to the Engineering Department on a weekly basis. Standard format of the checklist is attached. Automatic/manual chemical degreasing of the system to be activated for the hoods. If not, hoods to be thoroughly cleaned with high pressure steam. Engineering Department to check the working condition of the automatic cleaning system regularly. Annual Service of a specialized contractor to be hired top carry out the following. Complete cleaning of all horizontal ducts and the vertical riser. Smaller branches to be dismantled and cleaned. Use of eco-friendly chemicals for de-greasing. Policy Number: Effective Date: Objective: To eliminate grease collection from the hood and duct which is a fire hazard. Approved by: Title Superseding Policy KITCHEN EXTRACT HOOD & DUCT CLEANING Subject

5.9 Deviations: Requires written approval from the RVP Manual inspection doors should be provided every 6 meters straight and near smaller branches. If possible, video camera to be used to assess the condition of the ducts.

5.9 Swimming Pool Kitchen 7 Al Shaheen Kitchen 6 Laffan Kitchen 9 Laveranda Kitchen 8 Al Hubara Kitchen 5 Staff Cafeteria Kitchen 4 Pastry Kitchen 3 Oriental Kitchen 2 Main Kitchen 1 CLEANED(<) AREAS SN YEAR____________________ MONTH__________________ WEEK NO.________________ SAMPLE WEEKLY CHECKLIST FOR CLEANING OF KITCHEN HOOD FILTERS Signed by the Director & Engineering Signature Date __________________________ _________________________ Checked by Engineering Technician: Comments:

SOP ENGINEERING

More Related Content

What's hot (20)

Similar to SOP ENGINEERING (20)

More from Raghunath Patil (20)

Recently uploaded (20)

SOP ENGINEERING