Study on Strength Parameters of Concrete by adding Banana Fibers

International Research Journal of Engineering and Technology (IRJET) e-ISSN: 2395-0056
Volume: 07 Issue: 03 | Mar 2020 www.irjet.net p-ISSN: 2395-0072
© 2020, IRJET | Impact Factor value: 7.34 | ISO 9001:2008 Certified Journal | Page 4401
Study on Strength Parameters of Concrete by adding Banana Fibers
Mir Firasath Ali1, Syed Haseeb Ali 2, Mohammed Tanveer Ahmed 3, Shaik Khaja Patel4,
Mir Wahib Ali5
1Assistant Professor, Dept of Civil Engineering, ISL Engineering College, Hyderabad
2,3,4,5B.E Students, Dept of Civil Engineering, ISL Engineering College, Hyderabad
---------------------------------------------------------------------***----------------------------------------------------------------------
Abstract - This research describes experimental studies on
the utilization of banana trunk fiber to reinforce the strength
and applications of concrete. These natural fibers have
excellent physical and mechanical properties and may be
utilized more effectively. They’re economical, with no
chemicals. The addition of banana fibers significantly
improved many of the engineering properties of the concrete
notably compressive strength, tensile strength and flexural
strength. The flexibility to resist cracking and spalling were
also enhanced. Thus it acts as a natural admixture giving
additional properties to the ordinary cement concrete.During
this context different percentages of banana fibers 0%, 0.5%,
1%, 1.5%, having 50mm length were used. M30 concrete and
ordinary portland cement of grade 43 was used. The banana
fiber reinforced concrete is tested for compressive strength,
splitting tensile strength, flexural strength at different ages.
Key Words: Banana Fibres, natural admixture, High
strength concrete, reinforced concrete
1. INTRODUCTION
Fiber reinforced concrete (FRC) is a material created with
Portland cement, aggregate, and incorporating separate
discontinuous fibers. Traditional unreinforced concrete is
brittle with an occasional tensile strength and strain
capability. The addition ofBanana fiberstoconcretemakesit
additional homogenized and isotropic and transforms it
from a brittle to additional ductile materials. Conventional
concrete includes varied micro cracks that are quickly
exaggerated below the applied stresses. These cracks are
liable for the low tensile, flexural strength, and impact
resistance of concrete. Concrete strengthened with Banana
fibers impedes the crack growth and so enhances its
strength and impact characteristics however it'll conjointly
reduce the workability, the addition of super plasticizer(Sp)
is useful to resolve the potential drawback of
Tangling or balling of fibers.
1.1 Importance of Current Research
Despite the fact that concrete is a extensively used
construction material, it has important risks which includes
low tensile strength, impact resistance, and it's prone to
cracking. It is commonly assumed thatthebetterthestrength
of Concrete, the decrease its ductility in order that the found
inverse relationship among strength and ductility is taken
into consideration in a few structural application.
1.2 Research Objective
The plain concrete being brittle in nature there is a need to
make concrete a ductile material is of great importance. The
incorporation of Banana fibers as a randomly dispersed
reinforcement is an alternative answer, thepresenceoffiber
improve the tensile, flexural strength, ductility and much
extra efficient at controlling cracking at the aggregate –
matrix interface , however it is going to be also lessen the
workability . The addition of super plasticizer can enhance
the workability.
2. MATERIALS
Cement: Ordinary Portland cement of grade 43 is adopted
for this work. The brand of cement used was Ultra Tech OPC
with grade 43. The cement was gray and free from lumps.
Aggregates: In this research work fine aggregates used was
river sand zone II and coarse aggregates used were crushed
stones. These materials were easily available from local
market.
Water: Clean tap water was used for washing aggregates,
and mixing and curing of concretes.
Banana Fibers: The Banana trunk fibers used for this work
are from the local village, Tamilnadu region. The fibers are
available in processed and ready-to- use fibers. Uniform
length of fibers was obtained by using cutting machine.
Fig -1: Sample banana trunk fibers
Chemical treatment of Banana Fibers: Banana fibers have
a tendency to absorb water especially during the first few
hours after immersion in water. Alkali treatment of fibers
increases surface roughness which results in better
mechanical bonding and reduces water absorption. Hence

fibers are treated by immersing in 6% NaOH solution for 2
hours and then thoroughly washed by immersion in a clean
water tank to make fibers alkali free. Then fibersaredried in
oven at 80 degree centigrade for 24 hours.
Fig -2: Chemical treatment of fibers
3.METHODOLOGY&EXPERIMENTALPROGRAMME
1. Properties of various constituents of concrete viz,
Cement, fine aggregates, coarse aggregates and Banana
fibers were determined, by carrying out various tests.
2. Grade M30 concrete was designed as per IS: 10262 -2009,
which was used as reference mix.
3. Banana Fibers were added in 0%, 0.5%, 1%, and 1.5% by
volume of Concrete.
4. Cube, cylinders and beams were casted and curing was
done.
5. Compressive strength test, split tensile strength test and
Flexural test was done.
Mix Proportions for M30 grade of Concrete
Cement = 394.32 kg/m3
Water Content = 197.16 Liters
Fine aggregate = 623.45 kg/m3
Coarse aggregate 20mm = 1097.81 kg/m3
Fibers in kg/m3
0.5% = 11.56
1.0% = 23.12
1.5% = 34.69
Super plasticizer = 9.38 Liters
Fig -3: Chemically treated fibers
Fig -4: Mixing of Concrete with Fibers
The specimens of standard sizes and required shapes of
different mix proportions were casted for 7, 14, 28,days and
curing process is carried out after 24hrs from casting time.
Fig -5: Casted Specimens
5. RESULTS AND DISCUSSIONS
All the tests have been performed in standard procedures
and the results and load values obtained were tabulatedand
calculated in following sections.
5.1 Compressive Strength
Compressive strength tests were conducted on cured cube
specimen at 7 days and 28 days age using a compression
testing machine of 200 kN capacity. The cubes were fitted at
center in compression testing machine and fixed to keep the
cube in position. The load was then slowly applied to the
tested cube until failure.

Sl.no Mix (days)
Fiber
Content
Cube
Compressive
strength (N/mm2)
1 7
0% 34.7
0.5% 43.85
1% 42.3
1.5% 37.9
2 28
0% 49.5
0.5% 58.5
1% 55.6
1.5% 52.1
Table -5.1: Compressive Strength values
Chart -5.1: Compressive Strength
5.2 Split Tensile Strength
The split tensile test were conducted as per IS 5816:1999.
The size of cylinder is 300mm length with 150mm diameter.
The specimen werekept in water for curingfor7daysand28
days and on removal were tested in wet condition by wiping
water and grit present on the surface. The test is carried out
by placing a cylindrical specimen horizontally between the
loading surfaces of a compression testing machine and the
load is applied until failure of the cylinder along the vertical
diameter.
Sl.no Mix (days)
Fiber
Content
Cylinder
Split Tensile
strength (N/mm2)
1 7
0% 3.15
0.5% 3.55
1% 3.26
1.5% 2.90
2 28
0% 4.26
0.5% 4.65
1% 4.50
1.5% 4.0
Table -5.2: Split Tensile Strength values
Chart -5.2: Split Tensile Strength
5.3 Flexural Strength
The Flexural test were conducted as per IS 516:1959. The
size of beam is 150mm*150mm*700mm.Thespecimenwere
kept in water for curing for 28 days and on removal were
tested in wet condition by wiping water and grit present on
the surface. The test is carried out by placing a Beam
specimen horizontally such that the load shall be divided
equally between the two loading rollers, and all rollers shall
be mounted in such a manner that the load is applied axially
and without subjectingthespecimentoanytorsionalstresses
or restraints.
Sl.no Mix (days)
Fiber
Content
Beam
Flexural strength
(N/mm2)
1 28
0% 5.40
0.5% 6.3
1% 5.85
1.5% 5.22
Table -5.3: Flexure Strength values
Chart -5.3: Flexural Strength
6. SUMMARY AND CONCLUSIONS
The main objective of this study is to analyze the
performance of addition of commercially available Banana
trunk fibers as an additive in cementitious materials to

improve the mechanical properties of conventional concrete
and to enhance the flexibilitytoresistcrackingandspallingof
concrete structures.
The following conclusions were obtained as a result and
performance for the tests conducted..
The experimental tests unconcealed that the strength
properties of concrete improved with the addition of banana
trunk fibers to the concrete.
The conventionalmix&M30achievesacompressivestrength
of 34.17N/mm2, Split tensilestrength valuesof3.15N/mm2
and Flexural strength of 5.40 N/mm2 for 28 days of curing.
Compressive, flexural and split tensile strength of Banana
Fiber Reinforced Concrete are maximum at 0.5% fiber
content with 50mm fiber length.
The compressive strength obtained at 0.5% fiber content is
58.5 N/mm2 which is 18.18% higher than the reference
concrete strength with 0% fiber content.
The maximum split tensile strength attained at 0.5% fiber
content is 4.65 N/mm2, which is 9.1% higher than the
reference concrete strength with 0% fiber content.
The maximum flexural strength obtained at 0.5% fiber
content is 6.3 N/mm2, which is 16.64% higher than the
reference concrete strength with 0% fiber content.
It was observed that cracking resistance of the concrete
specimens improved to a greater extent and the specimens
were intact with each other even afterthefailureofspecimen
under loading thus making it a non brittle failure.
ACKNOWLEDGEMENT
We are thankful to Dr. Mohammed Masood, Principal,
ISLEC, for his encouragement throughout the project. We
would also like to express our heartfelt thanks to Ms. K.
Nanchari, Head of Civil Engineering Department, ISLEC for
her help and unending cooperation with us during
completion of this work.
REFERENCES
[1] Chandramouli, K. & Narayanan, Pannirselvam&Pardhu,
D.V.V. & Anitha, V.. (2019). Experimental investigation
on banana fibre reinforced concrete with conventional
concrete. International Journal of Recent Technology
and Engineering. 7. 874-876.
[2] Mouli, K. & Narayanan, Pannirselvam & Anitha, V. &
Kumar, D. & Rao, S.. (2019). Strength studies on banana
fibre concrete with metakaolin. International Journal of
Civil Engineering and Technology. 10. 684-689.
[3] S. KESAVRAMAN, 2017. STUDIES ON METAKAOLIN
BASED BANANA FIBRE REINFORCED
CONCRETE.International Journal of Civil Engineering
and Technology (IJCIET).Volume:8,Issue:1,Pages:532-
543.
[4] Ramakrishna G, Sundararajan T, “Impact strength of a
few natural fibre reinforced cement mortar slabs: a
comparative study,” Cement & Concrete Composites 27
(2005) 547–553.
[5] Solomon Ikechukwu Anowai and Olorunmeye Fredrick
Job, “Influence of Lengths and Volume FractionsofFibre
on Mechanical Properties of Banana Fibre Reinforced
Concrete” International Journal of Recent Innovation in
Engineering and Research, Scientific Journal Impact
Factor - 3.605 by SJIF, e- ISSN: 2456 – 2084.
[6] Mr. Solomon Ikechukwu Anowai, Prof. Olorunmeye
Fredrick Job, “Durability Properties of Banana Fibre
Reinforced Fly Ash Concrete”, International Research
Journal of Engineering and Technology, 4 (11), Nov -
2017, e-ISSN: 2395-0056, p-ISSN: 2395-0072.
[7] Forood Torabian Isfahani, Elena Redaelli, Federica
Lollini, Weiwen Li, and Luca Bertolini, “Effects of
Nanosilica on Compressive Strength and Durability
Properties of Concrete with Different Water to Binder
Ratios”, Hindawi Publishing Corporation Advances in
Materials Science andEngineering,Volume2016,Article
ID 8453567, 16 pages
BIOGRAPHIES
Mir Firasath Ali, Assistant
Professor, Department of Civil
Engineering, ISLEC, Hyderabad,
India
Syed Haseeb Ali, Student,
Department of Civil Engineering,
ISLEC, Hyderabad, India
Mohammed Tanveer Ahmed,
Student, Department of Civil
Engineering, ISLEC, Hyderabad,
India
Shaik Khaja Patel, Student,
Mir Wahib Ali, Student,

Study on Strength Parameters of Concrete by adding Banana Fibers

More Related Content

What's hot (20)

Similar to Study on Strength Parameters of Concrete by adding Banana Fibers (20)

Recently uploaded (20)

Study on Strength Parameters of Concrete by adding Banana Fibers