Terminal Part 3

Holding Aircraft– Clearance to Holding FixConsider operational factors such as length of delay, holding airspace limitations, navigational aids, altitude, meteorological conditions when necessary to clear an aircraft to a fix other than the destination airport. Issue the following: a. Clearance limit (if any part of the route beyond a clearance limit differs from the last routing cleared, issue the route the pilot can expect beyond the clearance limit). PHRASEOLOGY-EXPECT FURTHER CLEARANCE VIA (routing).b. Holding instructions. 1. Holding instructions may be eliminated when you inform the pilot that no delay is expected. 2. When the pattern is charted, you may omit all holding instructions except the charted holding direction and the statement “as published.” Always issue complete holding instructions when the pilot requests them. NOTE- The most generally used holding patterns are depicted on U.S. Government or commercially produced low/high altitude en route, area, and STAR Charts. PHRASEOLOGY- CLEARED TO (fix), HOLD (direction), AS PUBLISHED, or CLEARED TO (fix), NO DELAY EXPECTED.

Holding Aircraft– Clearance to Holding Fixc. EFC. Do not specify this item if no delay is expected. 1. When additional holding is expected at any other fix in your facility's area, state the fix and your best estimate of the additional delay. When more than one fix is involved, state the total additional en route delay (omit specific fixes). NOTE- Additional delay information is not used to determine pilot action in the event of two-way communications failure. Pilots are expected to predicate their actions solely on the provisions of 14 CFR Section 91.185. PHRASEOLOGY- EXPECT FURTHER CLEARANCE (time),and if required, ANTICIPATE ADDITIONAL (MM:HH) MINUTE/HOUR DELAY AT (fix),or ANTICIPATE ADDITIONAL (MM:HHMINUTE/HOUR EN ROUTE DELAY.2. When additional holding is expected in an approach control area, state the total additional terminal delay. PHRASEOLOGY-EXPECT FURTHER CLEARANCE (time),and if required,ANTICIPATE ADDITIONAL (MM:HH) MINUTE/HOUR TERMINAL DELAY.3. TERMINAL. When terminal delays exist or are expected, inform the appropriate center or approach control facility so that the information can be forwarded to arrival aircraft.4. When delay is expected, issue items in a. and b. at least 5 minutes before the aircraft is estimated to reach the clearance limit. If the traffic situation requires holding an aircraft that is less than 5 minutes from the holding fix, issue these items immediately. NOTE-1. The AIM indicates that pilots should start speed reduction when 3 minutes or less from the holding fix. The additional 2 minutes contained in the 5-minute requirement are necessary to compensate for different pilot/controller ETAS at the holding fix, minor differences in clock times, and provision for sufficient planning and reaction times. 2. When holding is necessary, the phrase “delay indefinite” should be used when an accurate estimate of the delay time and the reason for the delay cannot immediately be determined; i.e., disabled aircraft on the runway, terminal or center sector saturation, weather below landing minimums, etc. In any event, every attempt should be made to provide the pilot with the best possible estimate of his/her delay time and the reason for the delay. Controllers/supervisors should consult, as appropriate, with personnel (other sectors, weather forecasters, the airport management, other facilities, etc.) who can best provide this information.PHRASEOLOGY-DELAY INDEFINITE, (reason if known), EXPECT FURTHER CLEARANCE (time). (After determining the reason for the delay, advise the pilot as soon as possible.)

Holding Aircraft– Clearance Beyond Fixa. If no delay is expected, issue a clearance beyond the clearance limit as soon as possible and, whenever possible, at least 5 minutes before the aircraft reaches the fix. b. Include the following items when issuing clearance beyond a clearance limit: 1. Clearance limit or approach clearance. 2. Route of flight. Specify one of the following: (a) Complete details of the route (airway, route, course, fix(es), azimuth course, heading, arc, or vector.) (b) The phrase “via last routing cleared.” Use this phrase only when the most recently issued routing to the new clearance limit is valid and verbiage will be reduced. PHRASEOLOGY- VIA LAST ROUTING CLEARED. 3. Assigned altitude if different from present altitude. NOTE- Except in the event of a two-way communications failure, when a clearance beyond a fix has not been received, pilots are expected to hold as depicted on U.S. Government or commercially produced (meeting FAA requirements) low/high altitude en route and area or STAR charts. If no holding pattern is charted and holding instructions have not been issued, pilots should ask ATC for holding instructions prior to reaching the fix. If a pilot is unable to obtain holding instructions prior to reaching the fix, the pilot is expected to hold in a standard pattern on the course on which the aircraft approached the fix and request further clearance as soon as possible.

Holding Aircraft– Delaysa. Advise your supervisor or flow controller as soon as possible when you delay or expect to delay aircraft. b. When arrival delays reach or are anticipated to reach 30 minutes, take the following action: 1. TERMINAL. When tower en route control service is being provided, the approach control facility whose area contains the destination airport shall issue total delay information as soon as possible after the aircraft enters its approach control area. Whenever possible, the delay information shall be issued by the first terminal controller to communicate with the aircraft. 2. Unless a pilot requests delay information, the actions specified in 1 and 2 above may be omitted when total delay information is available to pilots via ATIS. PHRASEOLOGY- (Airport) ARRIVAL DELAYS (time in minutes/hours).

Holding Aircraft– Holding InstructionsWhen issuing holding instructions, specify: a. Direction of holding from the fix/waypoint. b. Holding fix or waypoint. NOTE- The holding fix may be omitted if included at the beginning of the transmission as the clearance limit.c. Radial, course, bearing, track, azimuth, airway, or route on which the aircraft is to hold. d. Leg length in miles if DME or RNAV is to be used. Specify leg length in minutes if the pilot requests it or you consider it necessary. e. Direction of holding pattern turns only if left turns are to be made, the pilot requests it, or you consider it necessary. PHRASEOLOGY-HOLD (direction) OF (fix/waypoint) ON (specified radial, course, bearing, track, airway, azimuth(s), or route.)If leg length is specified,(number of minutes/miles) MINUTE/MILE LEG.If direction of turn is specified,LEFT/RIGHT TURNS.f. Issue maximum holding airspeed advisories when an aircraft is: 1. Approved to exceed the maximum airspeed of a pattern, and is cleared into a holding pattern that will protect for the greater speed; or 2. Observed deviating from the holding pattern airspace area; or 3. Cleared into an airspeed restricted holding pattern in which the icon has not been published. EXAMPLE-Due to turbulence, a turboprop requests to exceed the recommended maximum holding airspeed. ATCS may clear the aircraft into a pattern that protects for the airspeed request, and shall advise the pilot of the maximum holding airspeed for the holding pattern airspace area. PHRASEOLOGY-“MAXIMUM HOLDING AIRSPEED IS TWO ONE ZERO KNOTS.”

Holding Aircraft– Visual Holding PointsYou may use as a holding fix a location which the pilot can determine by visual reference to the surface if he/she is familiar with it. PHRASEOLOGY-HOLD AT (location) UNTIL (time or other condition.)

Holding Aircraft– Holding Flight Path DeviationApprove a pilot's request to deviate from the prescribed holding flight path if obstacles and traffic conditions permit.

Holding Aircraft– Unmonitored NAVAIDsSeparate an aircraft holding at an unmonitored NAVAID from any other aircraft occupying the course which the holding aircraft will follow if it does not receive signals from the NAVAID.

Holding Aircraft– ILS ProtectionWhen conditions are less than reported ceiling 800 feet or visibility of 2 miles, do not authorize aircraft to hold below 5,000 feet AGL inbound toward the airport on or within 1 statute mile of the localizer between the ILS OM or the fix used in lieu of the OM and the airport. *USAF. The holding restriction applies only when an arriving aircraft is between the ILS OM or the fix used in lieu of the OM and the runway.

Arrival Procedures – Clearance Info.Clear an arriving aircraft to a clearance limit by specifying the following: a. Name of fix or airport. b. Route of flight including a STAR and STAR transition, if appropriate. Assign a STAR transition to any aircraft in lieu of other routes; e.g., airways or preferential arrival routes when the routings are the same. The clearance shall include the name and transition, if necessary, of the STAR to be flown.

Arrival Procedures – Clearance Info. TERMINAL: When the STAR transition is designed to provide course guidance to multiple runways, the facility shall state intended runway number on initial contact, or as soon as practical. If the runway assignment, or any subsequent runway change, is not issued prior to 10 NM from the runway transition waypoint, radar vectors to final shall be provided. PHRASEOLOGY- (STAR name and #) ARRIVAL. (STAR name and#) ARRIVAL, (transition name) TRANSITION. CHANGE/AMEND TRANSITION TO (runway number). CHANGE/AMEND TRANSITION TO (runway number) TURN LEFT/RIGHT or HEADING (heading) FOR VECTOR TO FINAL APPROACH COURSE. NOTE- If a civil pilot does not wish to use a STAR or FMSP issued in an ATC clearance or any other STAR published for that location, the pilot is expected to advise ATC.

Arrival Procedures – Clearance Info.c. Altitude instructions, as follows: 1. Assigned altitude; or 2. Instructions to vertically navigate on the STAR or STAR transition. d. Issue holding instructions, EFC, and additional delay information as required. e. Instructions regarding further communications as appropriate.

Arrival Procedures – Changes for Military A/CWhen military single-piloted turbojet aircraft will conduct an approach wholly or partly in IFR conditions or at night, take the following action: NOTE- It is known that the mental distraction and the inadvertent movement of aircraft controls resulting from the pilot's turning, reaching, or leaning to change frequencies can induce spatial disorientation (vertigo). a. Avoid radio frequency and radar beacon changes to the maximum extent that communications capabilities and traffic will permit. However, when changes are required: 1. Give instructions early enough to allow the change before the aircraft reaches the approach fix or handoff point. 2. Keep frequency/radar beacon changes to a minimum below 2,500 feet above the surface. 3. Avoid requiring frequency/radar beacon changes during the time the aircraft is making a turn. b. Avoid making frequency/radar beacon changes after an aircraft begins a high altitude approach. c. In the event of a missed approach, do not require a frequency/radar beacon change before the aircraft reaches the missed approach altitude, the MEA, or the MVA.

Arrival Procedures – Below Min. Report by PilotIf an arriving aircraft reports weather conditions are below his/her landing minima: NOTE- Determination that existing weather/visibility is adequate for approach/landing is the responsibility of the pilot/aircraft operator. a. Issue appropriate instructions to the aircraft to hold or proceed to another airport. b. Adjust, as necessary, the position in the landing sequence of any other aircraft desiring to make approaches and issue approach clearances accordingly.

Arrival Procedures – X-fer of JurisdictionTransfer radio communications and control responsibility early enough to allow the receiving facility to clear an aircraft beyond the clearance limit before the aircraft reaches it.

Arrival Procedures – Approach Informationa. Both en route and terminal approach control sectors shall provide current approach information to aircraft destined to airports for which they provide approach control services. This information shall be provided on initial contact or as soon as possible thereafter. Approach information contained in the ATIS broadcast may be omitted if the pilot states the appropriate ATIS code. For pilots destined to an airport without ATIS, items 3-5 below may be omitted after the pilot advises receipt of the automated weather; otherwise, issue approach information by including the following: 1. Approach clearance or type approach to be expected if two or more approaches are published and the clearance limit does not indicate which will be used. 2. Runway if different from that to which the instrument approach is made. 3. Surface wind. 4. Ceiling and visibility if the reported ceiling at the airport of intended landing is below 1,000 feet or below the highest circling minimum, whichever is greater, or the visibility is less than 3 miles. 5. Altimeter setting for the airport of intended landing. b. Upon pilot request, controllers shall inform pilots of the frequency where automated weather data may be obtained and, if appropriate, that airport weather is not available. PHRASEOLOGY- (Airport) AWOS/ASOS WEATHER AVAILABLE ON (frequency). 1. ASOS/AWOS shall be set to provide one minute weather at uncontrolled airports that are without ground-to-air weather broadcast capability by a CWO, NWS or FSS observer. 2. Controllers will consider the long-line disseminated weather from an automated weather system at an uncontrolled airport as trend information only and shall rely on the pilot for the current weather information for that airport. 3. Controllers shall issue the last long-line disseminated weather to the pilot if the pilot is unable to receive the ASOS/AWOS broadcast. NOTE- Aircraft destined to uncontrolled airports, which have automated weather data with broadcast capability, should monitor the ASOS/AWOS frequency to ascertain the current weather at the airport. The pilot should advise the controller when he/she has received the broadcast weather and state his/her intentions.

Arrival Procedures – Approach Informationc. Issue any known changes classified as special weather observations as soon as possible. Special weather observations need not be issued after they are included in the ATIS broadcast and the pilot states the appropriate ATIS code. d. Advise pilots when the ILS on the runway in use is not operational if that ILS is on the same frequency as an operational ILS serving another runway. e. TERMINAL: If multiple runway transitions are depicted on a STAR procedure, advise pilots of the runway assignment on initial contact or as soon as possible thereafter.

Arrival Procedures – Approach Info. By APRCH Facilities.a. Forward the following information to nonapproach control towers soon enough to permit adjustment of the traffic flow or to FSSs soon enough to provide local airport advisory where applicable: 1. Aircraft identification. 2. Type of aircraft. 3. ETA. 4. Type of instrument approach procedure the aircraft will execute; or 5. For SVFR, the direction from which the aircraft will enter Class B, Class C, Class D, or Class E surface area and any altitude restrictions that were issued; or 6. For aircraft executing a contact approach, the position of the aircraft. NOTE- Specific time requirements are usually stated in a letter of agreement.b. Forward the following information to the tower when the tower and TRACON are part of the same facility: 1. Aircraft identification. 2. Type aircraft if required for separation purposes. 3. Type of instrument approach procedure and/or runway if differing from that in use. c. Where the collocated or satellite tower has data displayed on its Certified Tower Radar Display (CTRD), the quick look functions may be used to forward arrival data provided that a facility directive at the collocated tower or a letter of agreement with the satellite tower exists which outlines procedures for use of transferring this data.

Arrival Procedures –Airport ConditionsOn first contact or as soon as possible thereafter, and subsequently as changes occur, inform an aircraft of any abnormal operation of approach and landing aids and of destination airport conditions that you know of which might restrict an approach or landing. This information may be omitted if it is contained in the ATIS broadcast and the pilot states the appropriate ATIS code.

Approach Clearance Procedures – Approach Clearance.a. Clear aircraft for “standard” or “special” instrument approach procedures only. To require an aircraft to execute a particular instrument approach procedure, specify in the approach clearance the name of the approach as published on the approach chart. Where more than one procedure is published on a single chart and a specific procedure is to be flown, amend the approach clearance to specify execution of the specific approach to be flown. If only one instrument approach of a particular type is published, the approach needs not be identified by the runway reference. An aircraft conducting an ILS approach when the glideslope/glidepathis reported out of service shall be advised at the time an approach clearance is issued. Standard Instrument Approach Procedures shall commence at an Initial Approach Fix or an Intermediate Approach Fix if there is not an Initial Approach Fix. Area Navigation (RNAV) Standard Instrument Approach Procedures may begin at an Intermediate Approach Fix for aircraft that have filed an Advanced RNAV equipment suffix when the conditions of b4 are met. Where adequate radar coverage exists, radar facilities may vector aircraft to the final approach course in accordance with vectors to final approach course. PHRASEOLOGY- CLEARED (type) APPROACH.For a straight-in-approach- IFR:CLEARED STRAIGHT-IN (type) APPROACH.To authorize a pilot to execute his/her choice of instrument approach:CLEARED APPROACH.Where more than one procedure is published on a single chart and a specific procedure is to be flown :CLEARED (specific procedure to be flown) APPROACH.To authorize a pilot to execute an ILS/MLS approach when the glideslope/glidepath is out of service:CLEARED (type) APPROACH, GLIDESLOPE/GLIDEPATH UNUSABLE.

Approach Clearance Procedures – Approach Clearance.NOTE-1. Clearances authorizing instrument approaches are issued on the basis that, if visual contact with the ground is made before the approach is completed, the entire approach procedure will be followed unless the pilot receives approval for a contact approach, is cleared for a visual approach, or cancels their IFR flight plan.2. Approach clearances are issued based on known traffic. The receipt of an approach clearance does not relieve the pilot of his/her responsibility to comply with applicable Parts of Title 14 of the Code of Federal Regulations and the notations on instrument approach charts which levy on the pilot the responsibility to comply with or act on an instruction; e.g., “Straight-in minima not authorized at night,” “Procedure not authorized when glideslope/ glidepath not used,” “Use of procedure limited to aircraft authorized to use airport,” or “Procedure not authorized at night.”3. The name of the approach, as published, is used to identify the approach, even though a component of the approach aid, other than the localizer on an ILS is inoperative. Where more than one procedure to the same runway is published on a single chart, each must adhere to all final approach guidance contained on that chart, even though each procedure will be treated as a separate entity when authorized by ATC. For example, Instrument Approach Procedures published on a chart as either HI-VOR/DME or TACAN 1 would be stated as either “HI V-O-R/D-M-E 1 Runway Six Left Approach” or “HI TACAN 1 Runway Six Left Approach.” The use of numerical identifiers in the approach name, or alphabetical identifiers with a letter from the end of the alphabet; e.g., X, Y, Z, such as “HI TACAN 1 Rwy 6L or HI TACAN 2 Rwy 6L,” or “RNAV (GPS) Z Rwy 04 or RNAV (GPS) Y Rwy 04,” denotes multiple straight-in approaches to the same runway that use the same approach aid. Alphabetical suffixes with a letter from the beginning of the alphabet; e.g., A, B, C, denote a procedure that does not meet the criteria for straight-in landing minimums authorization.4. 14 CFR Section 91.175(j) requires a pilot to receive a clearance for a procedure turn when vectored to a final approach fix or position, conducting a timed approach, or when the procedure specifies “NO PT.”5. An aircraft which has been cleared to a holding fix and prior to reaching that fix is issued a clearance for an approach, but not issued a revised routing; i.e., “proceed direct to . . ..” may be expected to proceed via the last assigned route, a feeder route (if one is published on the approach chart), and then to commence the approach as published. If, by following the route of flight to the holding fix, the aircraft would overfly an IAF or the fix associated with the beginning of a feeder route to be used, the aircraft is expected to commence the approach using the published feeder route to the IAF or from the IAF as appropriate; i.e., the aircraft would not be expected to overfly and return to the IAF or feeder route.6. Approach name items contained within parenthesis; e.g., RNAV (GPS) Rwy 04, are not included in approach clearance phraseology.

Approach Clearance Procedures – Approach Clearance.b. For aircraft operating on unpublished routes, issue the approach clearance only after the aircraft is: 1. Established on a segment of a published route or instrument approach procedure. 2. Assigned an altitude to maintain until the aircraft is established on a segment of a published route or instrument approach procedure. NOTE-1. The altitude assigned must assure IFR obstruction clearance from the point at which the approach clearance is issued until established on a segment of a published route or instrument approach procedure. 2. If the altitude assignment is VFR-on-top, it is conceivable that the pilot may elect to remain high until arrival over the final approach fix which may require the pilot to circle to descend so as to cross the final approach fix at an altitude that would permit landing.3. Established on a heading or course that will intercept the initial segment at the initial approach fix, or intermediate segment at the intermediate fix when no initial approach fix is published, for a GPS or RNAV instrument approach procedure at an angle not greater than 90 degrees. Angles greater than 90 degrees may be used when a hold in lieu of procedure turn pattern is depicted at the fix for the instrument approach procedure.

Approach Clearance Procedures – Approach Clearance. 4. Established on a heading or course that will intercept the intermediate segment at the intermediate fix, when an initial approach fix is published, provided the following conditions are met: (a) The instrument approach procedure is a GPS or RNAV approach. (b) Radar monitoring is provided to the Intermediate Fix. (c) The aircraft has filed an Advanced RNAV equipment suffix. (d) The pilot is advised to expect clearance direct to the Intermediate Fix at least 5 miles from the fix. (e) The aircraft is assigned an altitude to maintain until the Intermediate Fix. (f) The aircraft is on a course that will intercept the intermediate segment at an angle not greater than 90 degrees and is at an altitude that will permit normal descent from the Intermediate Fix to the Final Approach Fix. Controllers should expect aircraft to descend at approximately 300 feet per NM when applying this guidance.

Approach Clearance Procedures – Approach Clearance.c. Except when applying radar procedures, timed or visual approaches, clear an aircraft for an approach to an airport when the preceding aircraft has landed or canceled IFR flight plan. d. Where instrument approaches require radar monitoring and radar services are not available, do not use the phraseology “cleared approach,” which allows the pilot his/her choice of instrument approaches. e. Where a Terminal Arrival Area (TAA) has been established to support RNAV approaches use the procedures under b1. and b2.f. For GPS UNRELIABLE NOTAMs, inform pilots requesting a GPS or RNAV approach that GPS is unreliable and clear the aircraft for the approach. This advisory may be omitted if contained in the Automated Terminal Information System (ATIS) broadcast. g. For pilot reported GPS anomalies, advise subsequent aircraft requesting a GPS or RNAV approach that GPS is unreliable and clear the aircraft for the approach. This advisory may be discontinued after 15 minutes if no subsequent reports are received. PHRASEOLOGY- CLEARED (approach), GPS UNRELIABLE.

Approach Clearance Procedures – Approach Clearance.h. For Wide Area Augmentation System (WAAS) UNAVAILABLE NOTAMs, advise aircraft requesting a GPS or RNAV approach that WAAS is unavailable and clear the aircraft for the approach. This advisory may be omitted if contained in the ATIS broadcast. PHRASEOLOGY- CLEARED (approach), WAAS UNAVAILABLE. NOTE- 1. WAAS UNAVAILABLE NOTAMs indicate a failure of a WAAS system component. GPS/WAAS equipment reverts to GPS-only operation and satisfies the requirements for basic GPS equipment. 2. WAAS UNRELIABLE NOTAMs indicate predictive coverage, are published for pilot preflight planning, and do not require any controller action.

Approach Clearance Procedures – Clearance Limit.Issue approach or other clearances, as required, specifying the destination airport as the clearance limit if airport traffic control service is not provided even though this is a repetition of the initial clearance.

Approach Clearance Procedures –High Altitude IAPs.Altitudes above those shown on the high altitude instrument approach procedures chart may be specified when required for separation. NOTE- To preclude the possibility of aircraft exceeding rate-of-descent or airspeed limitations, the maximum altitudes which may be assigned for any portion of the high altitude instrument approach procedure will be determined through coordination between the ATC facility concerned and the military authority which originated the high altitude instrument approach procedure.

Approach Clearance Procedures –Specifying Altitude.Specify in the approach clearance the altitude shown in the approach procedures when adherence to that altitude is required for separation. When vertical separation will be provided from other aircraft by pilot adherence to the prescribed maximum, minimum, or mandatory altitudes, the controller may omit specifying the altitude in the approach clearance. NOTE- Use FAA or NIMA instrument approach procedures charts appropriate for the aircraft executing the approach.

Approach Clearance Procedures – Circling Approaches.a. Circling approach instructions may only be given for aircraft landing at airports with operational control towers. b. Include in the approach clearance instructions to circle to the runway in use if landing will be made on a runway other than that aligned with the direction of instrument approach. When the direction of the circling maneuver in relation to the airport/runway is required, state the direction (eight cardinal compass points) and specify a left or right base/downwind leg as appropriate. PHRASEOLOGY- CIRCLE TO RUNWAY (number), or CIRCLE (direction using eight cardinal compass points) OF THE AIRPORT/RUNWAY FOR A LEFT/RIGHT BASE/DOWNWIND TO RUNWAY (number).NOTE- Where standard instrument approach procedures (SIAPs) authorize circling approaches, they provide a basic minimum of 300 feet of obstacle clearance at the MDA within the circling area considered. The dimensions of these areas, expressed in distances from the runways, vary for the different approach categories of aircraft. In some cases a SIAP may otherwise restrict circling approach maneuvers.c. Do not issue clearances, such as “extend downwind leg,” which might cause an aircraft to exceed the circling approach area distance from the runways within which required circling approach obstacle clearance is assured.

Approach Clearance Procedures –Side-Steps.TERMINALSide-step Maneuver. When authorized by an instrument approach procedure, you may clear an aircraft for an approach to one runway and inform the aircraft that landing will be made on a parallel runway. EXAMPLE- “Cleared I-L-S Runway two seven left approach. Side-step to runway two seven right.” NOTE- Side-step maneuvers require higher weather minima/MDA. These higher minima/MDA are published on the instrument approach charts.

Approach Clearance Procedures –Communications Release.If an IFR aircraft intends to land at an airport not served by a tower or FSS, approve a change to the advisory service frequency when you no longer require direct communications. PHRASEOLOGY- CHANGE TO ADVISORY FREQUENCY APPROVED. NOTE- An expeditious frequency change permits the aircraft to receive timely local airport traffic information in accordance with AC 90-42, Traffic Advisory Practices at Airports Without Operating Control Towers.

Approach Clearance Procedures – Missed Approach.Except in the case of a VFR aircraft practicing an instrument approach, an approach clearance automatically authorizes the aircraft to execute the missed approach procedure depicted for the instrument approach being flown. An alternate missed approach procedure as published on the appropriate FAA Form 8260 or appropriate military form may be assigned when necessary. Once an aircraft commences a missed approach, it may be radar vectored. NOTE-1. Alternate missed approach procedures are published on the appropriate FAA Form 8260 or appropriate military form and require a detailed clearance when they are issued to the pilot. 2. In the event of a missed approach involving a turn, unless otherwise cleared, the pilot will proceed to the missed approach point before starting that turn.

Approach Clearance Procedures – Approach Info for Pilot.Specify the following in the approach clearance when the pilot says he/she is unfamiliar with the procedure: a. Initial approach altitude. b. Direction and distance from the holding fix within which procedure turn is to be completed. c. Altitude at which the procedure turn is to be made. d. Final approach course and altitude. e. Missed approach procedures if considered necessary. PHRASEOLOGY- INITIAL APPROACH AT (altitude), PROCEDURE TURN AT (altitude), (number) MINUTES/MILES (direction), FINAL APPROACH ON (name of NAVAID) (specified) COURSE/RADIAL/AZIMUTH AT (altitude).

Approach Clearance Procedures – Practice Approaches.Except for military aircraft operating at military airfields, ensure that neither VFR nor IFR practice approaches disrupt the flow of other arriving and departing IFR or VFR aircraft. Authorize, withdraw authorization, or refuse to authorize practice approaches as traffic conditions require. Normally, approaches in progress should not be terminated. NOTE- The priority afforded other aircraft over practice instrument approaches is not intended to be so rigidly applied that it causes grossly inefficient application of services.a. Separation. 1. IFR aircraft practicing instrument approaches shall be afforded standard separation in accordance with appropriate minima until: (a) The aircraft lands, and the flight is terminated, or (b) The pilot cancels the flight plan. 2. Where procedures require application of IFR separation to VFR aircraft practicing instrument approaches, standard IFR separation shall be provided. Controller responsibility for separation begins at the point where the approach clearance becomes effective. Except for heavy aircraft/B757, 500 feet vertical separation may be applied between VFR aircraft and between a VFR and an IFR aircraft. 3. Where separation services are not provided to VFR aircraft practicing instrument approaches, the controller shall; (a) Instruct the pilot to maintain VFR. (b) Advise the pilot that separation services are not provided. PHRASEOLOGY- “(Aircraft identification) MAINTAIN VFR, PRACTICE APPROACH APPROVED, NO SEPARATION SERVICES PROVIDED.” (c) Provide traffic information or advise the pilot to contact the appropriate facility. 4. If an altitude is assigned, including at or above/below altitudes, the altitude specified must meet MVA, minimum safe altitude, or minimum IFR altitude criteria. 5. All VFR aircraft shall be instructed to maintain VFR on initial contact or as soon as possible thereafter. NOTE- This advisory is intended to remind the pilot that even though ATC is providing IFR-type instructions, the pilot is responsible for compliance with the applicable parts of the CFR governing VFR flight.

Approach Clearance Procedures – Practice Approaches.b. Missed Approaches. 1. Unless alternate instructions have been issued, IFR aircraft are automatically authorized to execute the missed approach depicted for the instrument approach being flown. 2. VFR aircraft are not automatically authorized to execute the missed approach procedure. This authorization must be specifically requested by the pilot and approved by the controller. When a missed approach has been approved, separation shall be provided throughout the missed approach.

Approach Clearance Procedures –Low Approach / T+G.Consider an aircraft cleared for a touch-and-go, low approach, or practice approach as an arriving aircraft until that aircraft touches down or crosses the landing threshold; thereafter, consider the aircraft as a departing aircraft. Before the aircraft begins its final descent, issue the appropriate departure instructions the pilot is to follow upon completion of the approach (in accordance with departure clearances). Climb-out instructions must include a specific heading or a route of flight and altitude, except when the aircraft will maintain VFR and contact the tower. EXAMPLE- “After completing low approach, climb and maintain six thousand. Turn right, heading three six zero.”“Maintain VFR, contact tower.”(Issue other instructions as appropriate.) NOTE- Climb-out instructions may be omitted after the first approach if instructions remain the same.

Vectoring–Application.Vector aircraft: a. In controlled airspace for separation, safety, noise abatement, operational advantage, or when a pilot requests. Allow aircraft operating on an RNAV route to remain on their own navigation to the extent possible. b. In Class G airspace only upon pilot request and as an additional service. c. At or above the MVA or the minimum IFR altitude except as authorized for radar approaches, special VFR, VFR operations, or in, Vectors Below Minimum Altitude. NOTE- VFR aircraft not at an altitude assigned by ATC may be vectored at any altitude. It is the responsibility of the pilot to comply with the applicable parts of CFR Title 14.d. In airspace for which you have control jurisdiction, unless otherwise coordinated. e. So as to permit it to resume its own navigation within radar coverage. f. Operating special VFR only within Class B, Class C, Class D, or Class E surface areas. g. Operating VFR at those locations where a special program is established, or when a pilot requests, or you suggest and the pilot concurs.

Vectoring–Methods.a. Vector aircraft by specifying: 1. Direction of turn, if appropriate, and magnetic heading to be flown, or PHRASEOLOGY- TURN LEFT/RIGHT HEADING (degrees). FLY HEADING (degrees). FLY PRESENT HEADING. DEPART (fix) HEADING (degrees). 2. The number of degrees, in group form, to turn and the direction of turn, or PHRASEOLOGY- TURN (number of degrees) DEGREES LEFT/RIGHT. 3. For NO-GYRO procedures, the type of vector, direction of turn, and when to stop turn. PHRASEOLOGY- THIS WILL BE A NO-GYRO VECTOR, TURN LEFT/RIGHT. STOP TURN.

Vectoring–Methods.b. When initiating a vector, advise the pilot of the purpose. PHRASEOLOGY-VECTOR TO (fix or airway).VECTOR TO INTERCEPT (name of NAVAID) (specified) RADIAL.VECTOR FOR SPACING.VECTOR TO FINAL APPROACH COURSE,or if the pilot does not have knowledge of the type of approach,VECTOR TO (approach name) FINAL APPROACH COURSE. NOTE- Determine optimum routing based on factors such as wind, weather, traffic, pilot requests, noise abatement, adjacent sector requirement, and letters of agreement.c. Issue with the vector an altitude to maintain and all appropriate altitude restrictions when: 1. The vector will take the aircraft off an assigned procedure which contains altitude instructions, i.e., instrument approach, nonradar SID, FMSP, etc. 2. The previously issued clearance included crossing restrictions. d. If appropriate, advise the pilot what to expect when the vector is completed. PHRASEOLOGY- EXPECT TO RESUME (Route, SID, STAR, etc.). NOTE- You must ensure that the pilot is made aware if he/she is expected to resume a previously issued route procedure.

Vectoring–Methods.e. Provide radar navigational guidance until the aircraft is: 1. Established within the airspace to be protected for the nonradar route to be flown, or 2. On a heading that will, within a reasonable distance, intercept the nonradar route to be flown, and 3. Informed of its position unless the aircraft is RNAV, FMS, or DME equipped and being vectored toward a VORTAC/TACAN or waypoint and within the service volume of the NAVAID. PHRASEOLOGY- (Position with respect to course/fix along route),RESUME OWN NAVIGATION,orFLY HEADING (degrees). WHEN ABLE, PROCEED DIRECT (name of fix),or RESUME (SID/transition/STAR/procedure).

Vectoring–Methods.f. Aircraft instructed to resume a procedure which contains restrictions (SID/STAR/FMSP, etc.) shall be issued/reissued all applicable restrictions or shall be advised to comply with those restrictions. PHRASEOLOGY- RESUME (SID/transition/STAR), COMPLY WITH RESTRICTIONS.g. Aircraft vectored off an RNAV route shall be recleared to the next waypoint or as requested by the pilot. h. During stage A operation, update the route of flight in the computer unless an operational advantage is gained and coordination is accomplished. i. Inform the pilot when a vector will take the aircraft across a previously assigned nonradar route. PHRASEOLOGY- EXPECT VECTOR ACROSS (NAVAID radial) (airway/route/course) FOR (purpose).

Vectoring- Below Minimum Altitude.You may vector a departing IFR aircraft, or one executing a missed approach, within 40 miles of the antenna and before it reaches the minimum altitude for IFR operations if separation from prominent obstructions shown on the radar scope is applied in accordance with the following: a. If the flight path is 3 miles or more from the obstruction and the aircraft is climbing to an altitude at least 1,000 feet above the obstruction, vector the aircraft to maintain at least 3 miles separation from the obstruction until the aircraft reports leaving an altitude above the obstruction. b. If the flight path is less than 3 miles from the obstruction, and the aircraft is climbing to an altitude at least 1,000 feet above the obstruction, vector the aircraft to increase lateral separation from the obstruction until the 3 mile minimum is achieved or until the aircraft reports leaving an altitude above the obstruction. c. At those locations where diverse vector areas (DVA) have been established, terminal radar facilities may vector aircraft below the MVA/MIA within those areas and along those routes described in facility directives.

Speed Adjustment - ApplicationKeep speed adjustments to the minimum necessary to achieve or maintain required or desired spacing. Avoid adjustments requiring alternate decreases and increases. Permit pilots to resume normal speed when previously specified adjustments are no longer needed. NOTE- It is the pilot's responsibility and prerogative to refuse speed adjustment that he/she considers excessive or contrary to the aircraft's operating specifications.a. Consider the following when applying speed control: 1. Determine the interval required and the point at which the interval is to be accomplished. 2. Implement speed adjustment based on the following principles. (a) Priority of speed adjustment instructions is determined by the relative speed and position of the aircraft involved and the spacing requirement. (b) Speed adjustments are not achieved instantaneously. Aircraft configuration, altitudes, and speed determine the time and distance required to accomplish the adjustment. 3. Use the following techniques in speed control situations: (a) Compensate for compression when assigning air speed adjustment in an in-trail situation by using one of the following techniques: (1) Reduce the trailing aircraft first. (2) Increase the leading aircraft first. (b) Assign a specific airspeed if required to maintain spacing. (c) Allow increased time and distance to achieve speed adjustments in the following situations: (1) Higher altitudes. (2) Greater speed. (3) Clean configurations. (d) Ensure that aircraft are allowed to operate in a clean configuration as long as circumstances permit. (e) Keep the number of speed adjustments per aircraft to the minimum required to achieve and maintain spacing.

Speed Adjustment - Applicationb. Do not assign speed adjustment to aircraft: 1. At or above FL 390 without pilot consent. 2. Executing a published high altitude instrument approach procedure. 3. In a holding pattern. 4. Inside the final approach fix on final or a point 5 miles from the runway, whichever is closer to the runway. c. At the time approach clearance is issued, previously issued speed adjustments shall be restated if required. d. Approach clearances cancel any previously assigned speed adjustment. Pilots are expected to make their own speed adjustments to complete the approach unless the adjustments are restated. e. Express speed adjustments in terms of knots based on indicated airspeed (IAS) in 10-knot increments. NOTE- 1. Pilots complying with speed adjustment instructions should maintain a speed within plus or minus 10 knots. 2. When assigning speeds to achieve spacing between aircraft at different altitudes, consider that ground speed may vary with altitude. Further speed adjustment may be necessary to attain the desired spacing.

Speed Adjustment -Methodsa. Instruct aircraft to: 1. Maintain present/specific speed. 2. Maintain specified speed or greater/less. 3. Maintain the highest/lowest practical speed. 4. Increase or reduce to a specified speed or by a specified number of knots. PHRASEOLOGY- SAY AIRSPEED. MAINTAIN PRESENT SPEED. MAINTAIN (specific speed) KNOTS. MAINTAIN (specific speed) KNOTS OR GREATER. DO NOT EXCEED (speed) KNOTS. MAINTAIN MAXIMUM FORWARD SPEED. MAINTAIN SLOWEST PRACTICAL SPEED. INCREASE/REDUCE SPEED: TO (specified speed in knots), or (number of knots) KNOTS.

Speed Adjustment -MethodsNOTE-1. A pilot operating at or above 10,000 feet MSL on an assigned speed adjustment greater than 250 knots is expected to comply with 14 CFR Section 91.117(a) when cleared below 10,000 feet MSL, within domestic airspace, without notifying ATC. Pilots are expected to comply with the other provisions of 14 CFR Section 91.117 without notification.2. Speed restrictions of 250 knots do not apply to aircraft operating beyond 12 NM from the coastline within the U.S. Flight Information Region, in offshore Class E airspace below 10,000 feet MSL. However, in airspace underlying a Class B airspace area designated for an airport, or in a VFR corridor designated through such as a Class B airspace area, pilots are expected to comply with the 200 knot speed limit specified in 14 CFR Section 91.117(c). (See 14 CFR Sections 91.117(c) and 91.703.)3. The phrases “maintain maximum forward speed” and “maintain slowest practical speed” are primarily intended for use when sequencing a group of aircraft. As the sequencing plan develops, it may be necessary to determine the specific speed and/or make specific speed assignments.

Speed Adjustment -Methodsb. To obtain pilot concurrence for a speed adjustment at or above FL 390, as required by application, use the following phraseology. PHRASEOLOGY- (Speed adjustment), IF UNABLE ADVISE.

Speed Adjustment -Methodsc. Simultaneous speed reduction and descent can be extremely difficult, particularly for turbojet aircraft. Specifying which action is to be accomplished first removes any doubt the pilot may have as to controller intent or priority. Specify which action is expected first when combining speed reduction with a descent clearance. 1. Speed reductions prior to descent. PHRASEOLOGY- REDUCE SPEED: TO (specified speed), or (number of knots) KNOTS. THEN, DESCEND AND MAINTAIN (altitude). 2. Speed reduction following descent. PHRASEOLOGY- DESCEND AND MAINTAIN (altitude). THEN, REDUCE SPEED: TO (specified speed in knots), or (number of knots) KNOTS. NOTE- When specifying descent prior to speed reduction, consider the maximum speed requirements specified in 14 CFR Section 91.117. It may be necessary for the pilot to level off temporarily and reduce speed prior to descending below 10,000 feet MSL.

Speed Adjustment -Methodsd. Specify combined speed/altitude fix crossing restrictions. PHRASEOLOGY- CROSS (fix) AT AND MAINTAIN (altitude) AT (specified speed) KNOTS.

Speed Adjustment -MinimaWhen assigning airspeeds, use the following recommended minima: a. To aircraft operating between FL 280 and 10,000 feet, a speed not less than 250 knots.NOTE- If a pilot is unable to comply with the speed assignment, the pilot will advise.b. When an operational advantage will be realized, speeds lower than the recommended minima may be applied. c. To arrival aircraft operating below 10,000 feet: 1. Turbojet aircraft. A speed not less than 210 knots; except when the aircraft is within 20 flying miles of the runway threshold of the airport of intended landing, a speed not less than 170 knots. 2. Reciprocating engine and turboprop aircraft. A speed not less than 200 knots; except when the aircraft is within 20 flying miles of the runway threshold of the airport of intended landing, a speed not less than 150 knots. d. Departures: 1. Turbojet aircraft. A speed not less than 230 knots. 2. Reciprocating engine and turboprop aircraft. A speed not less than 150 knots. e. Helicopters. A speed not less than 60 knots.

Speed Adjustment – Termination.Advise aircraft when speed adjustment is no longer needed. PHRASEOLOGY- RESUME NORMAL SPEED.NOTE- An instruction to “resume normal speed” does not delete speed restrictions that are applicable to published procedures of upcoming segments of flight, unless specifically stated by ATC. This does not relieve the pilot of those speed restrictions which are applicable to 14 CFR Section 91.117.

Terminal Part 3

More Related Content

What's hot (16)

Similar to Terminal Part 3 (20)

Recently uploaded (20)

Terminal Part 3