Topic%20 compression
9 likes12,021 views
The document discusses compression members in structural engineering. It covers various types of compression members like columns in buildings, trusses, bridges, and towers. It discusses concepts like buckling, effective length, slenderness ratio, and different buckling modes. It provides examples of column shapes and failures. Formulas for critical load and effective length factors are presented. Considerations for real columns like residual stresses and initial imperfections are also covered.
Topic%20 compression
- 1. Dr. Seshu Adluri Structural Steel Design Compression Members
- 2. Columns in Buildings Compression members -Dr. Seshu Adluri
- 3. Columns in Buildings Compression members -Dr. Seshu Adluri
- 4. Column supports Compression members -Dr. Seshu Adluri
- 5. Compression members in trusses Compression members -Dr. Seshu Adluri
- 6. Compression members in trusses Compression members -Dr. Seshu Adluri
- 7. Compression members in OWSJ Compression members -Dr. Seshu Adluri
- 8. Compression members in bridges Howrah bridge, Kolkata, India Compression members -Dr. Seshu Adluri
- 9. Compression members in towers Eiffel Tower (1887 - 89) The new Tokyo Tower is set to be completed in 2011. It will stand 610m high. Compression members -Dr. Seshu Adluri
- 10. Compression in equipment Compression members -Dr. Seshu Adluri
- 11. Introduction Steel Compression members Building columns Frame Bracing Truss members (chords and bracing) Useful in pure compression as well as in beam- columns Design Clauses: CAN/CSA-S16 Over-all strength as per Clause 13.3 Local buckling check: Clause 11 (Table 1) Built-up members: Clause 19 Compression members -Dr. Seshu Adluri
- 12. Column erection Compression members -Dr. Seshu Adluri
- 13. Different column c/s shapes Compression members -Dr. Seshu Adluri
- 14. Different column c/s shapes Compression members -Dr. Seshu Adluri
- 15. Instability and bifurcation Stable, neutral and unstable equilibriums Compression members -Dr. Seshu Adluri
- 16. Buckling Compression members -Dr. Seshu Adluri
- 17. Instability and bifurcation Instability effect To compress or not to compress? Energy considerations Long column Compression members -Dr. Seshu Adluri
- 18. Compression terminology -review Moment of inertia I x = ∫ y 2 dA A Parallel axis theorem I = I + Ax x′ x 2 Radius of gyration r= I A Effective length kL Symmetric (major) Slenderness ratio kL/r axis h Principal axes (major and minor) Critical Load Pcr b Unsymmetric Factored compressive strength, Cr (minor) axis Compression members -Dr. Seshu Adluri
- 19. Compression members Bucking Elastic (Euler) buckling Inelastic buckling Buckling modes Overall buckling Flexural buckling Torsional buckling Torsional-flexural buckling Local buckling Compression members -Dr. Seshu Adluri
- 20. Elastic Buckling Equilibrium equation Internal moment + applied moment = 0 d 2w EI 2 + Pw = 0; w = 0 @ y = 0; w=0@ y = L dx πx Solution : w = A sin satisfies the b.c. L Substituting int o the differential equation, π 2 EI − A sin πx + P A sin πx = 0 L L L 2 π − EI + P = 0 L π 2 EI Pcr = 2 L Compression members -Dr. Seshu Adluri
- 21. Inelastic Buckling Compression members -Dr. Seshu Adluri
- 22. Compression members σpl = σy - κΛ/ρes Moment of inertia σpl = (0.5~1.0)σy Radius of gyration Effective length Slenderness ratio Compression members -Dr. Seshu Adluri
- 23. Effective length factors Different end conditions give different lengths for equivalent half-sine wave Compression members -Dr. Seshu Adluri
- 24. Theoretical Effective length factors Compression members -Dr. Seshu Adluri
- 25. Theoretical Effective length factors Compression members -Dr. Seshu Adluri
- 26. Effective length factors US practice Compression members -Dr. Seshu Adluri
- 27. Effective lengths in different directions Compression members -Dr. Seshu Adluri
- 28. Effective length factors Canadian practice k = .65 k = .8 k = 1.2 k = 1.0 k = 2.0 k = 2.0 Compression members -Dr. Seshu Adluri
- 29. US recommended Engrg. Eff. Boundary Theoretical Eff. values Length Conditions Length, LeffT LeffE Free-Free L (1.2·L) Hinged-Free L (1.2·L) Hinged-Hinged L L (Simply-Supported) Guided-Free 2·L (2.1·L) Guided-Hinged 2·L 2·L Guided-Guided L 1.2·L Clamped-Free 2·L 2.1·L (Cantilever) Clamped-Hinged 0.7·L 0.8·L Clamped-Guided L 1.2·L Clamped-Clamped 0.5·L 0.65·L Compression members -Dr. Seshu Adluri
- 30. Canadian recommended Engrg. Eff. Boundary Theoretical Eff. values – Length Appendix F Conditions Length, LeffT CAN/CSA/S16-01 LeffE Free-Free L (1.2·L) Hinged-Free L (1.2·L) Hinged-Hinged L L (Simply-Supported) Guided-Free 2·L (2.0·L) Guided-Hinged 2·L 2·L Guided-Guided L 1.2·L Clamped-Free 2·L 2.0·L (Cantilever) Clamped-Hinged 0.7·L 0.8·L Clamped-Guided L 1.2·L Clamped-Clamped 0.5·L 0.65·L Compression members -Dr. Seshu Adluri
- 31. Effective lengths in frame columns Compression members -Dr. Seshu Adluri
- 32. Effective lengths in frame columns Compression members -Dr. Seshu Adluri
- 33. Real columns -Factors for consideration Partially plastic buckling Initial out-of- straightness (L/2000 to L/1000) Compression members -Dr. Seshu Adluri
- 34. Real columns - Factors for consideration Residual stresses in Hot-rolled shapes (idealized) Compression members -Dr. Seshu Adluri
- 35. Real columns - Factors for consideration Residual stresses in Hot-rolled shapes (idealized) Compression members -Dr. Seshu Adluri
- 36. Perfect column failure Compression members -Dr. Seshu Adluri
- 37. Perfect column failure Compression members -Dr. Seshu Adluri
- 38. Practical column failure Compression members -Dr. Seshu Adluri
- 39. Column curve Compression members -Dr. Seshu Adluri
- 40. Intermediate Short Column Long Column Column (Strength (Elastic Stability (Inelastic Limit) Limit) Material Stability Limit) Slenderness Ratio ( kL/r = Leff / r) Structural Steel kL/r < 40 40 < kL/r < 150 kL/r > 150 Aluminum Alloy kL/r < 9.5 9.5 < kL/r < 66 kL/r > 66 AA 6061 - T6 Aluminum Alloy kL/r < 12 12 < kL/r < 55 kL/r > 55 AA 2014 - T6 Wood kL/r < 11 11 < kL/r < (18~30) (18~30)<kL/r<50 Compression members -Dr. Seshu Adluri
- 41. Over-all buckling Flexural Torsional Torsional-flexural Compression members -Dr. Seshu Adluri
- 42. Flexural Buckling About minor axis (with higher kL/R) for doubly symmetric shapes About minor axis (the unsymmetric axis) for singly symmetric shapes 1964 Alaska quake, EqIIS collection Compression members -Dr. Seshu Adluri
- 43. Flexural Buckling Compression members -Dr. Seshu Adluri
- 44. Torsional buckling Short lengths Usually kL/r less than approx. 50 doubly symmetric sections Wide flange sections, cruciform sections, double channels, point symmetric sections, …. Not for closed sections such as HSS since they are very strong in torsion Compression members -Dr. Seshu Adluri
- 45. Torsion Torque is a moment that causes twisting along the length of a bar. The twist is also the torsional deformation. For a circular shaft, the torque (or torsional moment) rotates each c/s relative to the nearby c/s. Compression members -Dr. Seshu Adluri
- 46. Torsional deformation Compression members -Dr. Seshu Adluri
- 47. Torsion of non-circular sections Torsion of non-circular sections involves torsional shear and warping. Torsional shear needs the use of torsion constant J. J is similar to the use of polar moment of inertia for circular shafts. J=Σbt3/3 Warping calculation needs the use od the constant Cw. Both J and Cw are listed in the Handbook In addition, we need to use the effective length in torsion (kzLz). Usually, kz is taken as 1.0 Compression members -Dr. Seshu Adluri
- 48. Torsional buckling of open sections Buckling in pure torsional mode (not needed for HSS or closed sections): Kz is normally taken as 1.0. Cw, J, rx, ry are given in the properties tables, x and y are the axes of symmetry of the section. E= 200 000 MPa (assumed), G=77 000 MPa (assumed). 1 π 2 ECw Fez = + GJ ro2 = xo + yo + rx2 + ry2 2 2 Aro ( K z L ) 2 2 Fy ( ) −1 n λ= Cr = φ AFy 1 + λ 2n Fe Compression members -Dr. Seshu Adluri
- 49. Shear centre Sections always rotate about shear centre Shear centre lies on the axis of symmetry Compression members -Dr. Seshu Adluri
- 50. Torsional- flexural buckling For of singly symmetric sections, about the major axis For unsymmetric sections, about any axis Rotation is always about shear centre Compression members -Dr. Seshu Adluri
- 51. Torsional-flexural buckling Compression members -Dr. Seshu Adluri
- 52. Shear flow Compression members -Dr. Seshu Adluri
- 53. Shear flow Compression members -Dr. Seshu Adluri
- 54. Shear flow Compression members -Dr. Seshu Adluri
- 55. Shear centre Compression members -Dr. Seshu Adluri
- 56. Shear flow effect Compression members -Dr. Seshu Adluri
- 57. Shear centre Compression members -Dr. Seshu Adluri
- 58. Shear centre Compression members -Dr. Seshu Adluri
- 59. Local (Plate) buckling Compression members -Dr. Seshu Adluri
- 60. Plate buckling Compression members -Dr. Seshu Adluri
- 61. Plate buckling Effective width concept Compression members -Dr. Seshu Adluri
- 62. Plate buckling Different types of buckling depending on b/t ratio end conditions for plate segments Table 1 for columns Table 2 for beams and beam-columns Compression members -Dr. Seshu Adluri
- 63. Web buckling Compression members -Dr. Seshu Adluri
- 64. Plate buckling b/t ratio effect Compression members -Dr. Seshu Adluri
- 65. Built-up columns Two or more sections Stitch bolts Batten plates Lacing Combined batten & lacing Perforated cover plates Compression members -Dr. Seshu Adluri
- 66. Built-up columns Two or more sections Stitch bolts Batten plates Lacing Combined Compression members -Dr. Seshu Adluri
- 67. Built-up columns Compression members -Dr. Seshu Adluri
- 68. Built-up columns Closely spaced channels Compression members -Dr. Seshu Adluri
- 69. Built-up columns Built-up member buckling is somewhat similar to frame buckling Batten acts like beams Battens get shear and moment due to the bending of the frame like built-up member at the time of buckling Compression members -Dr. Seshu Adluri
- 70. Battened column Compression members -Dr. Seshu Adluri
- 71. Built-up columns Design as per normal procedure Moment of inertia about the axis which shifts due to the presence of gap needs parallel axis theorem Effective slenderness ratio as per Cl. 19.1 Compression members -Dr. Seshu Adluri
- 72. References AISC Digital Library (2008) ESDEP-the European Steel Design Education Programme - lectures Earthquake Image Information System Hibbeler, R.C., 2008. “Mechanics of Solids,” Prentice-Hall Compression members -Dr. Seshu Adluri