hazardous waste environmental protection and control

Hazardous Waste
1 Environmental Pollution and Control| Syed Jeelani Basha Asst Prof.
Unit 5
Hazardous Waste: Characterization – Nuclear waste – Biomedical wastes – Electronic wastes –
Chemical wastes – Treatment and management of hazardous waste-Disposal and Control
methods.
Hazardous waste is waste that poses substantial or potential threats to public health or the
environment.
Hazardous wastes refer to wastes that may cause adverse health effects on the ecosystem and
human beings.
These wastes pose present or potential risks to human health or living organisms, due to the fact
that they are
 Non-degradable or persistent in nature;
 Biologically magnified;
 Highly toxic and even lethal at very low concentrations.
Characteristics of hazardous wastes
The regulations define characteristic hazardous wastes as wastes that exhibit measurable
properties posing sufficient threats to warrant regulation. For a waste to be deemed a
characteristic hazardous waste, it must cause, or significantly contribute to, an increased mortality
or an increase in serious irreversible or incapacitating reversible illness, or pose a substantial
hazard or threat of a hazard to human health or the environment, when it is improperly treated,
stored, transported, disposed of, or otherwise mismanaged.
(i) Ignitability: A waste is an ignitable hazardous waste, if it has a flash point of less than 60o
C;
readily catches fire and burns so vigorously as to create a hazard; or is an ignitable compressed
gas or an oxidiser. A simple method of determining the flash point of a waste is to review the
material safety data sheet, which can be obtained from the manufacturer or distributor of the
material. Naphtha, lacquer thinner, epoxy resins, adhesives and oil based paints are all examples
of ignitable hazardous wastes.
(ii) Corrosivity: A liquid waste which has a pH of less than or equal to 2 or greater than or equal
to 12.5 is considered to be a corrosive hazardous waste. Sodium hydroxide, a caustic solution
with a high pH, is often used by many industries to clean or degrease metal parts. Hydrochloric
acid, a solution with a low pH, is used by many industries to clean metal parts prior to painting.
When these caustic or acid solutions are disposed of, the waste is a corrosive hazardous waste.
(iii) Reactivity: A material is considered a reactive hazardous waste, if it is unstable, reacts
violently with water, generates toxic gases when exposed to water or corrosive materials, or if it

Hazardous Waste
is capable of detonation or explosion when exposed to heat or a flame. Examples of reactive
wastes would be waste gunpowder, sodium metal or wastes containing cyanides or sulphides.
(iv) Toxicity: To determine if a waste is a toxic hazardous waste, a representative sample of the
material must be subjected to a test conducted in a certified laboratory. The toxic characteristic
identifies wastes that are likely to leach dangerous concentrations of toxic chemicals into ground
water.
Classification
From a practical standpoint, there are far too many compounds, products and product
combinations that fit within the broad definition of hazardous waste. For this reason, groups of
waste are considered in the following five general categories:
(i) Radioactive substance: Substances that emit ionising radiation are radioactive. Such
substances are hazardous because prolonged exposure to radiation often results in damage to
living organisms. Radioactive substances are of special concern because they persist for a long
period. The period in which radiation occurs is commonly measured and expressed as half-life,
i.e., the time required for the radioactivity of a given amount of the substance to decay to half its
initial value. For example, uranium compounds have half-lives that range from 72 years for U232
to 23,420,000 years for U236. The management of radioactive wastes is highly controlled by
national and state regulatory agencies. Disposal sites that are used for the long-term storage of
radioactive wastes are not used for the disposal of any other solid waste.
(ii) Chemicals: Most hazardous chemical wastes can be classified into four groups: synthetic
organics, inorganic metals, salts, acids and bases, and flammables and explosives. Some of the
chemicals are hazardous because they are highly toxic to most life forms. When such hazardous
compounds are present in a waste stream at levels equal to, or greater than, their threshold levels,
the entire waste stream is identified as hazardous.
(iii) Biomedical wastes: The principal sources of hazardous biological wastes are hospitals and
biological research facilities. The ability to infect other living organisms and the ability to
produce toxins are the most significant characteristics of hazardous biological wastes. This group
mainly includes malignant tissues discarded during surgical procedures and contaminated
materials, such as hypodermic needles, bandages and outdated drugs. This waste can also be
generated as a by-product of industrial biological conversion processes.
(iv) Flammable wastes: Most flammable wastes are also identified as hazardous chemical
wastes. This dual grouping is necessary because of the high potential hazard in storing, collecting
and disposing of flammable wastes. These wastes may be liquid, gaseous or solid, but most often
they are liquids. Typical examples include organic solvents, oils, plasticisers and organic sludges.

Hazardous Waste
(v) Explosives: Explosive hazardous wastes are mainly ordnance (artillery) materials, i.e., the
wastes resulting from ordnance manufacturing and some industrial gases. Similar to flammables,
these wastes also have a high potential for hazard in storage, collection and disposal, and
therefore, they should be considered separately in addition to being listed as hazardous chemicals.
These wastes may exist in solid, liquid or gaseous form.
vi) Household hazardous wastes: Household wastes such as cleaning chemicals, batteries, nail
polish etc in MSW constitute hazardous waste. Especially batteries contain mercury which are
alkaline which is dangerous enough to kill people. Generic household hazardous material include
non-chlorinated organic, chlorinated organic, pesticides, latex paint, oil based paints, waste oil,
automobile battery and household battery.
Nuclear or Radioactive waste
Radioactive waste is waste that contains radioactive material. Radioactive waste is usually a by-
product of nuclear power generation and other applications of nuclear fission or nuclear
technology, such as research and medicine. Radioactive waste is hazardous to most forms of life
and the environment, and is regulated by government agencies in order to protect human health
and the environment.
Radioactivity naturally decays over time, so radioactive waste has to be isolated and confined in
appropriate disposal facilities for a sufficient period until it no longer poses a threat. The time
radioactive waste must be stored for depends on the type of waste and radioactive isotopes.
Current major approaches to managing radioactive waste have been segregation and storage for
short-lived waste, near-surface disposal for low and some intermediate level waste, and deep
burial or partitioning / transmutation for the high-level waste.
Sources of radioactive waste:
Radioactive waste comes from a number of sources
Nuclear fuel cycle
Nuclear weapons decommissioning
Medical
Industrial
Naturally occurring radioactive material (NORM)

Hazardous Waste
Management of radioactive waste:
1 Initial treatment of waste
1.1 Vitrification
Long-term storage of radioactive waste requires the stabilization of the waste into a form which
will neither react nor degrade for extended periods. It is theorized that one way to do this might
be through vitrification.
Currently at Sellafield the high-level waste is mixed with sugar and then calcined.
Calcination involves passing the waste through a heated, rotating tube. The purposes of
calcination are to evaporate the water from the waste, and de-nitrate the fission products to assist
the stability of the glass produced.
The 'calcine' generated is fed continuously into an induction heated furnace with fragmented
glass. The resulting glass is a new substance in which the waste products are bonded into the
glass matrix when it solidifies. As a melt, this product is poured into stainless steel cylindrical
containers (―cylinders‖) in a batch process. When cooled, the fluid solidifies (―vitrifies‖) into the
glass. After being formed, the glass is highly resistant to water. After filling a cylinder, a seal is
welded onto the cylinder head. The cylinder is then washed. After being inspected for external
contamination, the steel cylinder is stored usually in an underground repository. In this form, the
waste products are expected to be immobilized for thousands of years.
1.2 Ion exchange
It is common for medium active wastes in the nuclear industry to be treated with ion exchange or
other means to concentrate the radioactivity into a small volume. The much less radioactive bulk
(after treatment) is often then discharged. For instance, it is possible to use a ferric hydroxide floc
to remove radioactive metals from aqueous mixtures. After the radioisotopes are absorbed onto
the ferric hydroxide, the resulting sludge can be placed in a metal drum before being mixed with
cement to form a solid waste form. In order to get better long-term performance (mechanical
stability) from such forms, they may be made from a mixture of fly ash, or blast furnace slag, and
Portland cement, instead of normal concrete (made with Portland cement, gravel and sand).
1.3 Synroc
The Australian Synroc (synthetic rock) is a more sophisticated way to immobilize such waste,
and this process may eventually come into commercial use for civil wastes (it is currently being
developed for US military wastes). Synroc was invented by Prof Ted Ringwood (a geochemist) at
the Australian National University. The Synroc contains pyrochlore and cryptomelane type
minerals. The original form of Synroc (Synroc C) was designed for the liquid high level waste
from a light water reactor. The main minerals in this Synroc are
hollandite (BaAl2Ti6O16), zirconolite (CaZrTi2O7) and perovskite (CaTiO3). The zirconolite
and perovskite are hosts for the actinides. The strontium and barium will be fixed in the
perovskite. The caesium will be fixed in the hollandite.

Hazardous Waste
2 Long term management of waste
The time frame in question when dealing with radioactive waste ranges from 10,000 to 1,000,000
years, according to studies based on the effect of estimated radiation doses. Researchers suggest
that forecasts of health detriment for such periods should be examined critically. Practical studies
only consider up to 100 years as far as effective planning and cost evaluations are concerned.
Long term behaviour of radioactive wastes remains a subject for ongoing research projects in
geoforecasting.
2.1 Above-ground disposal
Dry cask storage typically involves taking waste from a spent fuel pool and sealing it (along with
an inert gas) in a steel cylinder, which is placed in a concrete cylinder which acts as a radiation
shield. It is a relatively inexpensive method which can be done at a central facility or adjacent to
the source reactor. The waste can be easily retrieved for reprocessing.
2.2 Geologic disposal
The process of selecting appropriate deep final repositories for high level waste and spent fuel is
now under way in several countries with the first expected to be commissioned sometime after
2010. The basic concept is to locate a large, stable geologic formation and use mining technology
to excavate a tunnel, or large-bore tunnel boring machines (similar to those used to drill the
Channel Tunnel from England to France) to drill a shaft 500 metres to 1,000 metres below the
surface where rooms or vaults can be excavated for disposal of high-level radioactive waste. The
goal is to permanently isolate nuclear waste from the human environment.
Many people remain uncomfortable with the immediate stewardship cessation of this disposal
system, suggesting perpetual management and monitoring would be more prudent.
Because some radioactive species have half-lives longer than one million years, even very low
container leakage and radionuclide migration rates must be taken into account. Moreover, it may
require more than one half life until some nuclear materials lose enough radioactivity to cease
being lethal to living things. A 1983 review of the Swedish radioactive waste disposal program
by the National Academy of Sciences found that country’s estimate of several hundred thousand
years—perhaps up to one million years—being necessary for waste isolation ―fully justified.‖
Ocean floor disposal of radioactive waste has been suggested by the finding that deep waters in
the North Atlantic Ocean do not present an exchange with shallow waters for about 140 years
based on oxygen content data recorded over a period of 25 years. They include burial beneath a
stable abyssal plain, burial in a subduction zone that would slowly carry the waste downward into
the Earth’s mantle, and burial beneath a remote natural or human-made island. While these
approaches all have merit and would facilitate an international solution to the problem of disposal
of radioactive waste, they would require an amendment of the Law of the Sea.

Hazardous Waste
2.3 Re-use of waste
Main article: Nuclear reprocessing
Another option is to find applications for the isotopes in nuclear waste so as to re-use them.
Already, caesium-137, strontium-90 and a few other isotopes are extracted for certain industrial
applications such as food irradiation and radioisotope thermoelectric generators. While re-use
does not eliminate the need to manage radioisotopes, it reduces the quantity of waste produced.
The Nuclear Assisted Hydrocarbon Production
Method, Canadian patent application 2,659,302, is a method for the temporary or permanent
storage of nuclear waste materials comprising the placing of waste materials into one or more
repositories or boreholes constructed into an unconventional oil formation. The thermal flux of
the waste materials fractures the formation and alters the chemical and/or physical properties of
hydrocarbon material within the subterranean formation to allow removal of the altered material.
A mixture of hydrocarbons, hydrogen, and/or other formation fluids is produced from the
formation. The radioactivity of high-level radioactive waste affords proliferation resistance to
plutonium placed in the periphery of the repository or the deepest portion of a borehole.
Breeder reactors can run on U-238 and transuranic elements, which comprise the majority of
spent fuel radioactivity in the 1,000–100,000-year time span.
2.4 Space disposal
Space disposal is attractive because it removes nuclear waste from the planet. It has significant
disadvantages, such as the potential for catastrophic failure of a launch vehicle, which could
spread radioactive material into the atmosphere and around the world. A high number of launches
would be required because no individual rocket would be able to carry very much of the material
relative to the total amount that needs to be disposed of. This makes the proposal impractical
economically and it increases the risk of at least one or more launch failures.
To further complicate matters, international agreements on the regulation of such a program
would need to be established. Costs and inadequate reliability of modern rocket launch systems
for space disposal has been one of the motives for interest in non-rocket space launch systems
such as mass drivers, space elevators, and other proposals.
3 National management plans
Most countries are considerably ahead of the United States in developing plans for high-level
radioactive waste disposal.
4 Illegal dumping
Authorities in Italy are investigating a 'Ndrangheta mafia clan accused of trafficking and illegally
dumping nuclear waste. According to a whistleblower, a manager of the Italy’s state energy
research agency Enea paid the clan to get rid of 600 drums of toxic and radioactive waste from
Italy, Switzerland, France, Germany, and the US, with Somalia as the destination, where the
waste was buried after buying off local politicians. Former employees of Enea are suspected of
paying the criminals to take waste off their hands in the 1980s and 1990s.

Hazardous Waste
Biomedical waste
Biomedical waste is any kind of waste containing infectious (or potentially infectious)
materials.[1] It may also include waste associated with the generation of biomedical waste that
visually appears to be of medical or laboratory origin (e.g., packaging, unused bandages, infusion
kits, etc.), as well research laboratory waste containing biomolecules or organisms that are
restricted from environmental release.
Biomedical waste may be solid or liquid. Examples of infectious waste include discarded blood,
sharps, unwanted microbiological cultures and stocks, identifiable body parts (including those as
a result of amputation), other human or animal tissue, used bandages and dressings, discarded
gloves, other medical supplies that may have been in contact with blood and body fluids, and
laboratory waste that exhibits the characteristics described above. Waste sharps include
potentially contaminated used (and unused discarded) needles, scalpels, lancets and other devices
capable of penetrating skin.
Biomedical waste is generated from biological and medical sources and activities, such as the
diagnosis, prevention, or treatment of diseases. Common generators (or producers) of biomedical
waste include hospitals, health clinics, nursing homes, medical research laboratories, offices of
physicians, dentists, and veterinarians, home health care, and funeral homes. In healthcare
facilities (i.e., hospitals, clinics, doctors offices, veterinary hospitals and clinical laboratories),
waste with these characteristics may alternatively be called medical or clinical waste.
Risk to human health
Disposal of this waste is an environmental concern, as many medical wastes are classified as
infectious or biohazardous and could potentially lead to the spread of infectious disease. The most
common danger for humans is the infection which also affects other living organisms in the
region. Daily exposure to the waste (landfill) leads to accumulation of harmful substances or
microbes in the person’s body.
Management
Biomedical waste must be properly managed and disposed of to protect the environment, general
public and workers, especially healthcare and sanitation workers who are at risk of exposure to
biomedical waste as an occupational hazard. Steps in the management of biomedical waste
include generation, accumulation, handling, storage, treatment, transport and disposal.
1. On-site and off-site
Disposal occurs off-site, at a location that is different from the site of generation. Treatment may
occur onsite or off-site. On-site treatment of large quantities of biomedical waste usually requires
the use of relatively expensive equipment, and is generally only cost effective for very large

Hazardous Waste
hospitals and major universities who have the space, labour and budget to operate such
equipment. Offsite treatment and disposal involves hiring of a biomedical waste disposal service
(also called a truck service) whose employees are trained to collect and haul away biomedical
waste in special containers (usually cardboard boxes, or reusable plastic bins) for treatment at a
facility designed to handle biomedical waste.
2. Generation and accumulation
Biomedical waste should be collected in containers that are leak-proof and sufficiently strong to
prevent breakage during handling. Containers of biomedical waste are marked with a biohazard
symbol. The container, marking, and labels are often red.
Discarded sharps are usually collected in specialized boxes, often called needle boxes.
3. Handling
Handling refers to the act of manually moving biomedical waste between the point of generation,
accumulation areas, storage locations and on-site treatment facilities.
Workers who handle biomedical waste should observe standard precautions.
4. Treatment
The goals of biomedical waste treatment are to reduce or eliminate the waste’s hazards, and
usually to make the waste unrecognizable. Treatment should render the waste safe for subsequent
handling and disposal. There are several treatment methods that can accomplish these goals.
Biomedical waste is often incinerated. An efficient incinerator will destroy pathogens and sharps.
Source materials are not recognizable in the resulting ash.
An autoclave may also be used to treat biomedical waste.
An autoclave uses steam and pressure to sterilize the waste or reduce its microbiological load to a
level at which it may be safely disposed of. Many healthcare facilities routinely use an autoclave
to sterilize medical supplies. If the same autoclave is used to sterilize supplies and treat
biomedical waste, administrative controls must be used to prevent the waste operations from
contaminating the supplies.
Effective administrative controls include operator training, strict procedures, and separate times
and space for processing biomedical waste.
For liquids and small quantities, a 1–10% solution of bleach can be used to disinfect biomedical
waste. Solutions of sodium hydroxide and other chemical disinfectants may also be used,
depending on the waste’s characteristics. Other treatment methods include heat, alkaline digesters
and the use of microwaves.
For autoclaves and microwave systems, a shredder may be used as a final treatment step to render
the waste unrecognizable.
The international symbol for biological hazard

Hazardous Waste
In India, The Bio-medical Waste (Management and Handling)
Rules, 1998 and further amendments were passed for the regulation of bio-medical waste
management. On 28 th March 2016 Biomedical Waste Management Rules 2016 were also
notified by Central Govt. Each state’s Pollution Control Board or Pollution control Committee
will be responsible for implementing the new legislation.
In India, there are a number of different disposal methods, yet most are harmful rather than
helpful. If body fluids are present, the material needs to be incinerated or put into an autoclave.
Although this is the proper method, most medical facilities fail to follow the regulations. It is
often found that biomedical waste is put into the ocean, where it eventually washes up on shore,
or in landfills due to improper sorting when in the medical facility. Improper disposal can lead to
many diseases in animals as well as humans. For example, animals, such as cows in Pondicherry,
India, are consuming the infected waste and eventually, these infections can be transported to
humans through eating of the meat.
Electronic waste
Electronic waste or E-waste describes discarded electrical or electronic devices. Used
electronics which are destined for reuse, resale, salvage, recycling, or disposal are also considered
e-waste. Informal processing of e waste in developing countries can lead to adverse human health
effects and environmental pollution.
Electronic scrap components, such as CPUs, contain potentially harmful components such as
lead, cadmium, beryllium, or brominated flame retardants. Recycling and disposal of e-waste
may involve significant risk to workers and communities in developed countries and great care
must be taken to avoid unsafe exposure in recycling operations and leaking of materials such as
heavy metals from landfills and incinerator ashes.
―Electronic waste‖ or ―E-Waste‖ may be defined as discarded computers, office electronic
equipment, entertainment device electronics, mobile phones, television sets, and refrigerators.
This includes used electronics which are destined for reuse, resale, salvage, recycling, or disposal.

Hazardous Waste
Others are re-usables (working and repairable electronics) and secondary scrap (copper, steel,
plastic, etc.) to be ―commodities‖, and reserve the term ―waste‖ for residue or material which is
dumped by the buyer rather than recycled, including residue from reuse and recycling operations,
because loads of surplus electronics are frequently commingled (good, recyclable, and non-
recyclable), several public policy advocates apply the term ―e-waste‖ broadly to all surplus
electronics. Cathode ray tubes (CRTs) are considered one of the hardest types to recycle.
Environmental impact
The processes of dismantling and disposing of electronic waste in developing countries led to a
number of environmental impacts as illustrated in the graphic. Liquid and atmospheric releases
end up in bodies of water, groundwater, soil, and air and therefore in land and sea animals – both
domesticated and wild, in crops eaten by both animals and human, and in drinking water.
One study of environmental effects in Guiyu, China found the following:
 Airborne dioxins – one type found at 100 times levels previously measured
 Levels of carcinogens in duck ponds and rice paddies exceeded international standards for
agricultural areas and cadmium, copper, nickel, and lead levels in rice paddies were above
international standards
 Heavy metals found in road dust – lead over 300 times that of a control village’s road dust
and copper over 100 times
E-waste management
Recycling
One of the major challenges is recycling the printed circuit boards from the electronic wastes.
The circuit boards contain such precious metals as gold, silver, platinum, etc. and such base
metals as copper, iron, aluminum, etc.
One way e-waste is processed is by melting circuit boards, burning cable sheathing to recover
copper wire and open pit acid leaching for separating metals of value. Conventional method
employed is mechanical shredding and separation but the recycling efficiency is low. Alternative
methods such as cryogenic decomposition have been studied for printed circuit board recycling,
and some other methods are still under investigation. Properly disposing of or reusing electronics
can help prevent health problems, reduce greenhouse-gas emissions, and create jobs. Reuse and
refurbishing offer a more environmentally friendly and socially conscious alternative to down-
cycling processes.

Hazardous Waste
Chemical waste
A chemical waste is a solid, liquid, or gaseous material that displays either a ―Hazardous
Characteristic‖ or is specifically ―listed‖ by name as a hazardous waste.
There are four characteristics chemical wastes may have to be considered as hazardous. These are
Ignitability, Corrosivity, Reactivity, and Toxicity. This type of hazardous waste must be
categorized as to its identity, constituents, and hazards so that it may be safely handled and
managed.
Laboratory waste containers
Packaging, labelling, storage are the three requirements for disposing chemical waste.
1. Packaging
For packaging, chemical liquid waste containers should only be filled up to 75% capacity to
allow for vapour expansion and to reduce potential spills which could occur from moving
overfilled containers. Container material must be compatible with the stored hazardous waste.
Finally, wastes must not be packaged in containers that improperly identify other non existing
hazards.
In addition to the general packaging requirements mentioned above, incompatible materials
should never be mixed together in a single container. Wastes must be stored in containers
compatible with the chemicals stored as mentioned in the container compatibility section.
Solvent safety cans should to be used to collect and temporarily store large volumes (10–20 litres)
of flammable organic waste solvents, precipitates, solids or other non-fluid wastes should not be
mixed into safety cans.
2. Labelling
Label all containers with the group name from the chemical waste category and an itemized list
of the contents.
All chemicals or anything contaminated with chemicals posing a significant hazard. All waste
must be appropriately packaged.
3. Storage
When storing chemical wastes, the containers must be in good condition and should remain
closed unless waste is being added. Hazardous waste must be stored safely prior to removal from
the laboratory and should not be allowed to accumulate. Container should be sturdy and
leakproof, also has to be labeled. All liquid waste must be stored in leakproof containers with a
screw- top or other secure lid. Snap caps, mis-sized caps, parafilm and other loose fitting lids are
not acceptable. If necessary, transfer waste material to a container that can be securely closed.
Keep waste containers closed except when adding waste. Secondary containment should be in
place to capture spills and leaks from the primary container, segregate incompatible hazardous
wastes, such as acids and bases.

Hazardous Waste
Hazardous waste management
1. Generation
Hazardous wastes are generated in limited amounts in a community and very little information is
available on the quantities of hazardous waste generated within a community and in various
industries. Hazardous waste generation outside the industry is irregular and very less in amount,
rendering the waste generation parameter meaningless. The only practical means to overcome
these limitations is to conduct a detailed inventory and measurement studies at each potential
source in a community. As a first step in developing a community inventory, potential sources of
hazardous waste are to be identified. The total annual quantity of hazardous waste at any given
source in a community must be established through data inventory completed during onsite visits.
Waste
Category
Sources
Radioactive
substances
Biomedical research facilities, colleges and
university laboratories, offices, hospitals, nuclear
power plants, etc.
Toxic
chemicals
Agricultural chemical companies, battery shops,
car washes, chemical shops, college and university
laboratories, construction companies, electric
utilities, hospitals and clinics, industrial cooling
towers, newspaper and photographic solutions,
nuclear power plants, pest control agencies,
photographic processing facilities, plating shops,
service stations, etc.
Biological
wastes
Biomedical research facilities, drug companies,
hospitals, medical clinics, etc.
Flammable
wastes
Dry cleaners, petroleum reclamation plants,
petroleum refining and processing facilities,
service stations, tanker truck cleaning stations, etc.
Explosives Construction companies, dry cleaners, ammunition
production facilities, etc.
2. Storage and collection
Onsite storage practices are a function of the types and amounts of hazardous wastes generated
and the period over which generation occurs. Usually, when large quantities are generated,
special facilities are used that have sufficient capacity to hold wastes accumulated over a period
of several days. When only a small amount is generated, the waste can be containerised, and
limited quantity may be stored. Containers and facilities used in hazardous waste storage and
handling are selected on the basis of waste characteristics. For example, corrosive acids or caustic
solutions are stored in fibreglass or glass-lined containers to prevent deterioration of metals in the

Hazardous Waste
container. Great care must also be exercised to avoid storing incompatible wastes in the same
container or locations.
Light-Gauge Closed Head Drum
Light-Gauge Open Head Drum
The waste generator, or a specialised hauler, generally collects the hazardous waste for delivery
to a treatment or disposal site. The loading of collection vehicles is completed in either of the
following ways:
(i) Wastes stored in large-capacity tanks are either drained or pumped into collection vehicles;
(ii) Wastes stored in sealed drums or sealed containers are loaded by hand or by mechanical
equipment onto flatbed trucks.
3. Transfer and transport

Hazardous Waste
The facilities of a hazardous waste transfer station are quite different from solid waste transfer
station. Typically, hazardous wastes are not compacted (i.e., mechanical volume reduction) or
delivered by numerous community residents. Instead, liquid hazardous wastes are generally
pumped from collection vehicles and sludge or solids are reloaded without removal from the
collection containers for transport to processing and disposal facilities.
It is unusual to find a hazardous waste transfer facility, where wastes are simply transferred to
larger transport vehicles. Some processing and storage facilities are often part of the material
handling sequence at a transfer station.
4. Processing
Processing of hazardous waste is done for purposes of recovering useful materials and preparing
the wastes for disposal.
Processing can be accomplished on-site or off-site. The variables affecting the selection of
processing site include the characteristics of wastes, the quantity of wastes, the technical,
economical and environmental aspects of available on-site treatment processes and the
availability of the nearest off-site treatment facility (e.g., haul distance, fees, and exclusions). The
treatment of hazardous waste can be accomplished by physical, chemical, thermal or biological
means.
5. Disposal
Regardless of their form (i.e., solid, liquid, or gas), most hazardous waste is disposed off either
near the surface or by deep burial.
Hazardous waste treatment
1.Physical and chemical treatment
Physical and chemical treatments are an essential part of most hazardous waste treatment
operations, and the treatments include the following
(i) Filtration and separation: Filtration is a method for separating solid particles from a liquid
using a porous medium. The driving force in filtration is a pressure gradient, caused by gravity,
centrifugal force, vacuum, or pressure greater than atmospheric pressure. The application of
filtration for treatment of hazardous waste fall into the following categories:
 Clarification, in which suspended solid particles less than 100 ppm (parts per million)
concentration are removed from an aqueous stream. This is usually accomplished by depth
filtration and cross-flow filtration and the primary aim is to produce a clear aqueous effluent,
which can either be discharged directly, or further processed. The suspended solids are
concentrated in a reject stream.
 Dewatering of slurries of typically 1% to 30 % solids by weight. Here, the aim is to
concentrate the solids into a phase or solid form for disposal or further treatment. This is
usually accomplished by cake filtration. The filtration treatment, for example, can be used for
neutralisation of strong acid with lime or limestone, or precipitation of dissolved heavy

Hazardous Waste
metals as carbonates or sulphides followed by settling and thickening of the resulting
precipitated solids as slurry. The slurry can be dewatered by cake filtration and the effluent
from the settling step can be filtered by depth filtration prior to discharge.
(ii) Chemical precipitation: This is a process by which the soluble substance is converted to an
insoluble form either by a chemical reaction or by change in the composition of the solvent to
diminish the solubility of the substance in it. Settling and/or filtration can then remove the
precipitated solids. In the treatment of hazardous waste, the process has a wide applicability in the
removal of toxic metal from aqueous wastes by converting them to an insoluble form. This
includes wastes containing arsenic, barium, cadmium, chromium, copper, lead, mercury, nickel,
selenium, silver, thallium and zinc. The sources of wastes containing metals are metal plating and
polishing, inorganic pigment, mining and the electronic industries. Hazardous wastes containing
metals are also generated from cleanup of uncontrolled hazardous waste sites, e.g., leachate or
contaminated ground water.
(iii) Chemical oxidation and reduction (redox): In these reactions, the oxidation state of one
reactant is raised, while that of the other reactant is lowered. When electrons are removed from an
ion, atom, or molecule, the substance is oxidised and when electrons are added to a substance, it
is reduced. Such reactions are used in treatment of metal-bearing wastes, sulphides, cyanides and
chromium and in the treatment of many organic wastes such as phenols, pesticides and sulphur
containing compounds. Since these treatment processes involve chemical reactions, both
reactants are generally in solution. However, in some cases, a solution reacts with a slightly
soluble solid or gas.
There are many chemicals, which are oxidising agents; but relatively few of them are used for
waste treatment. Some of the commonly used oxidising agents are sodium hypochlorite,
hydrogen peroxide, calcium hypochlorite, potassium permanganate and ozone. Reducing agents
are used to treat wastes containing hexavalent chromium, mercury, organometallic compounds
and chelated metals. Some of the compounds used as reducing agents are sulphur dioxide, sodium
borohydride, etc. In general, chemical treatment costs are highly influenced by the chemical cost.
This oxidation and reduction treatment tends to be more suitable for low concentration (i.e., less
than 1%) in wastes.
(iv) Solidification and stabilisation: In hazardous waste management, solidification and
stabilisation (S/S) is a term normally used to designate a technology employing activities to
reduce the mobility of pollutants, thereby making the waste acceptable under current land
disposal requirements. Solidification and stabilisation are treatment processes designed to
improve waste handling and physical characteristics, decrease surface area across which
pollutants can transfer or leach, limit the solubility or detoxify the hazardous constituent. To
understand this technology, it is important for us to understand the following terms:
Solidification: This refers to a process in which materials are added to the waste to produce a
solid. It may or may not involve a chemical bonding between the toxic contaminant and the
additive.
Stabilisation: This refers to a process by which a waste is converted to a more chemically stable
form. Subsuming solidification, stabilisation represents the use of a chemical reaction to
transform the toxic component to a new, non-toxic compound or substance.

Hazardous Waste
Chemical fixation: This implies the transformation of toxic contaminants to a new non-toxic
compound. The term has been misused to describe processes, which do not involve chemical
bonding of the contaminant to the binder.
Encapsulation: This is a process involving the complete coating or enclosure of a toxic particle
or waste agglomerate with a new substance (e.g., S/S additive or binder). The encapsulation of
the individual particles is known as micro-encapsulation, while that of an agglomeration of waste
particles or micro-encapsulated materials is known as macro-encapsulation.
In S/S method, some wastes can be mixed with filling and binding agents to obtain a
dischargeable product. This rather simple treatment can only be used for waste with chemical
properties suitable for landfilling. With regard to wastes with physical properties, it changes only
the physical properties, but is unsuitable for landfilling. The most important application of this
technology, however, is the solidification of metal-containing waste. S/S technology could
potentially be an important alternative technology with a major use being to treat wastes in order
to make them acceptable for land disposal. Lower permeability, lower contaminant leaching rate
and such similar characteristics may make hazardous wastes acceptable for land disposal after
stabilisation.
(v) Evaporation: Evaporation is defined as the conversion of a liquid from a solution or slurry
into vapour. All evaporation systems require the transfer of sufficient heat from a heating medium
to the process fluid to vaporise the volatile solvent. Evaporation is used in the treatment of
hazardous waste and the process equipment is quite flexible and can handle waste in various
forms – aqueous, slurries, sludges and tars. Evaporation is commonly used as a pre-treatment
method to decrease quantities of material for final treatment. It is also used in cases where no
other treatment method was found to be practical, such as in the concentration of trinitrotoluene
(TNT) for subsequent incineration.
(vi) Ozonation: Ozone is a relatively unstable gas consisting of three oxygen atoms per molecule
(O3) and is one of the strongest oxidising agents known. It can be substituted for conventional
oxidants such as chlorine, hydrogen peroxide and potassium permanganate. Ozone and UV
radiations have been used to detoxify industrial organic wastes, containing aromatic and aliphatic
polychlorinated compounds, ketones and alcohols.
2 Thermal treatment
The two main thermal treatments used with regard to hazardous wastes are:
(i) Incineration: Incineration can be regarded as either a pre-treatment of hazardous waste, prior
to final disposal or as a means of valorising waste by recovering energy. It includes both the
burning of mixed solid waste or burning of selected parts of the waste stream as a fuel. The
concept of treating hazardous waste is similar to that of municipal solid waste.
(ii) Pyrolysis: This is defined as the chemical decomposition or change brought about by heating
in the absence of oxygen. This is a thermal process for transformation of solid and liquid
carbonaceous materials into gaseous components and the solid residue containing fixed carbon
and ash. The application of pyrolysis to hazardous waste treatment leads to a two-step process for
disposal. In the first step, wastes are heated separating the volatile contents (e.g., combustible
gases, water vapour, etc.) from non-volatile char and ash. In the second step volatile components
are burned under proper conditions to assure incineration of all hazardous components.

Hazardous Waste
To elaborate, pyrolysis is applicable to hazardous waste treatment, as it provides a precise control
of the combustion process. The first step of pyrolysis treatment is endothermic and generally
done at 425 to 760o
C. The heating chamber is called the pyrolyser. Hazardous organic
compounds can be volatilised at this low temperature, leaving a clean residue. In the second step,
the volatiles are burned in a fume incinerator to achieve destruction efficiency of more than 99%.
Separating the process into two very controllable steps allows precise temperature control and
makes it possible to build simpler equipment. The pyrolysis process can be applied to solids,
sludges and liquid wastes. Wastes with the following characteristics are especially amenable to
pyrolysis:
 Sludge material that is either too viscous, too abrasive or varies too much in consistency
to be atomised in an incinerator.
 Wastes such as plastic, which undergo partial or complete phase changes during thermal
processing.
 High-residue materials such as high-ash liquid and sludges, with light, easily entrained
solids that will generally require substantial stack gas clean up.
 Materials containing salts and metals, which melt and volatilise at normal incineration
temperatures. Materials like sodium chloride (NaCl), zinc (Zn) and lead (Pb), when
incinerated may cause refractory spalling and fouling of the heat-exchanger surface.
3 Biological treatment
On the basis of the fact that hazardous materials are toxic to living beings, it is not uncommon for
some to assume that biological treatment is not possible for hazardous wastes. This assumption is
untenable, and, in fact, we must aggressively seek biological treatment in order to exploit the full
potential of hazardous wastes in terms of removal efficiency and cost. Against this background,
let us now list some of the techniques used for biological treatment of hazardous waste:
(i) Land treatment: This is a waste treatment and disposal process, where a waste is mixed with
or incorporated into the surface soil and is degraded, transformed or immobilised through proper
management. The other terminologies used commonly include land cultivation, land farming,
land application and sludge spreading. Compared to other land disposal options (e.g., landfill and
surface impoundments), land treatment has lower long-term monitoring, maintenance and
potential clean up liabilities and because of this, it has received considerable attention as an
ultimate disposal method. It is a dynamic, management-intensive process involving waste, site,
soil, climate and biological activity as a system to degrade and immobilise waste constituents.
In land treatment, the organic fraction must be biodegradable at reasonable rates to minimise
environmental problems associated with migration of hazardous waste constituents. The various
factors involved in the operation of the system are as follows:
Waste characteristics: Biodegradable wastes are suitable for land treatment. Radioactive wastes,
highly volatile, reactive, flammable liquids and inorganic wastes such as heavy metals, acids and
bases, cyanides and ammonia are not considered for land treatment. Land treatability of organic
compound often follows a predictable pattern for similar type of compounds. Chemical structure,

Hazardous Waste
molecular weight, water solubility and vapour pressure are few of the characteristics that
determine the ease of biodegradation.
Soil characteristics: The rate of biodegradation and leaching of waste applied, the availability of
nutrients and toxicants to microorganisms and the fate of hazardous waste constituents are
determined largely by application rate as well as the soil’s chemical and physical characteristics
or reaction. Principal soil characteristics affecting land treatment processes are pH, salinity,
aeration, moisture holding capacity, soil temperature, etc. Some of the characteristics can be
improved through soil amendments (e.g., nutrients, lime, etc.), tillage or through adjustments of
loading rate, frequency, etc., at the time of waste application.
Microorganisms: Soil normally contains a large number of diverse microorganisms, consisting
of several groups that are predominantly aerobic in well-drained soil. The types and population of
microorganisms present in the waste-amended soil depend on the soil moisture content, available
oxygen, nutrient composition and other characteristics. The key groups of the microorganisms
present in the surface soil are bacteria, actinomycetes, fungi, algae and protozoa. In addition to
these groups, other micro and macro fauna, such as nematodes and insects are often present.
Waste degradation: Conditions favourable for plant growth are also favourable for the activity
of soil microorganisms. The factors affecting waste degradation that (may be adjusted in the
design and operation of a land treatment facility) are soil pH (near 7), soil moisture content
(usually between 30 to 90 %), soil temperature (activity decreases below 10o
C) and nutrients.
(ii) Enzymatic systems: Enzymes are complex proteins ubiquitous in nature. These proteins,
composed of amino acids, are linked together via peptide bonds. Enzymes capable of
transforming hazardous waste chemicals to non-toxic products can be harvested from
microorganisms grown in mass culture. Such crude enzyme extracts derived from
microorganisms have been shown to convert pesticides into less toxic and persistent products.
The reaction of detoxifying enzymes are not limited to intracellular conditions but have been
demonstrated through the use of immobilised enzyme extracts on several liquid waste streams.
The factors of moisture, temperature, aeration, soil structure, organic matter content, seasonal
variation and the availability of soil nutrients influence the presence and abundance of enzymes.
(iii) Composting: The principles involved in composting organic hazardous wastes are the same
as those in the composting of all organic materials, though with moderate modifications. The
microbiology of hazardous wastes differs from that of composting in the use of inoculums. The
reaction is that certain types of hazardous waste molecules can be degraded by only one or a very
few microbial species, which may not be widely distributed or abundant in nature. The factors
important in composting of hazardous wastes are those that govern all biological reactions. The
principal physical parameters are the shape and dimensions of the particles of the material to be
composted and the environmental factors of interest in an operation are temperature, pH,
available oxygen, moisture, and nutrient availability.
(iv) Aerobic and anaerobic treatment: Hazardous materials are present in low to high
concentration in wastewaters, leachate and soil. These wastes are characterised by high organic
content (e.g., up to 40,000 mg/l total organic carbon), low and high pH (2 to 12), elevated salt
levels (sometimes, over 5%), and presence of heavy metals and hazardous organics. Hazardous
wastes can be treated using either aerobic or anaerobic treatment methods.

Hazardous Waste
In aerobic treatment, under proper conditions, microorganisms grow. They need a carbon and
energy source, which many hazardous wastes satisfy, nutrients such as nitrogen, phosphorus and
trace metals and a source of oxygen. Some organisms can use oxidised inorganic compounds (e.g.
nitrate) as a substitute for oxygen. Care is to be taken such that all the required nutrients and
substances are supplied in sufficient quantities. Temperature and pH must be controlled as needed
and the substances that are toxic to the organisms (e.g., heavy metals) must be removed.
Anaerobic treatment is a sequential biologically destructive process in which hydrocarbons are
converted, in the absence of free oxygen, from complex to simpler molecules, and ultimately to
carbon dioxide and methane. The process is mediated through enzyme catalysis and depends on
maintaining a balance of population within a specific set of environmental conditions. Hazardous
waste streams often consist of hydrocarbons leading to higher concentrations of chemical oxygen
demand (COD). Depending upon the nature of waste, the organic constituents may be derived
from a single process stream or from a mixture of streams.
The treatability of the waste depends upon the susceptibility of the hydrocarbon content to
anaerobic biological degradation, and on the ability of the organisms to resist detrimental effect
of biologically recalcitrant and toxic organic and inorganic chemicals. The metabolic interactions
among the various groups of organisms are essential for the successful and complete
mineralisation of the organic molecules. Various parameters such as the influent quality, the
biological activity of the reactor and the quality of the reactor environment are monitored to
maintain efficient operating conditions within the reactor.

hazardous waste environmental protection and control

More Related Content

What's hot (20)

Viewers also liked (20)

Similar to hazardous waste environmental protection and control (20)

Recently uploaded (20)

hazardous waste environmental protection and control