Wi-Fi Connection Manual (eng)
0 likes215 views
1. The Wi-Fi dongle automatically creates a Wi-Fi network when turned on. iOS devices must connect to this network to communicate with the esa system. 2. After connecting to the Wi-Fi network, users may need to manually configure their iOS device to use a static IP address for improved stability. 3. Once connected, users can start receiving data from the esa system by turning on the "Wi-Fi" switch in the esa app's home screen. Temporary connection issues will trigger an error message but automatic reconnection attempts will be made.
Wi-Fi Connection Manual (eng)
- 1. WI-FI CONNECTION MANUAL 1 v. 1.4 11-2012 news a pg 3-4
- 2. Wi-Fi Management Turning on the esa system is devided into three simple steps to be performed in sequence.Lʼaccensione del sistema esa si articola in tre semplici passaggi da effettuare in sequenza. 1. Turning on the dongle esa 1 2 When the dongle is on (usually toghether with instruments) it will automatically creating specific Wi-Fi network, during this phase the red led blinks, at the end of the process will be on permanently. 1. Led Power (red): power on 2. Led Wi-Fi (blue) : Wi-Fi connection activeted The DONGLE, automatically, at the first time you connect with the program esa it enables the functionality and access to the system encrypted; esa software does not work with GESTIONE WI-FI VERSIONE 1.2 03-2012 2
- 3. other Wi-Fi systems. 3
- 4. 2. Access to the Wi-Fi network with iOS device Before making the connection to the astra board you need to activate wifi on the device and connect to the astra network. To do this you need to access the wifi network device and activate the service by clicking to the left of astra board (check that the number indicated corresponds to your number of dongle). New Version 1.4 Select automatic login to the network. ESA is set for dynamic access management (DHCP), but with the latest operating system (iOS 6 or later) is recommended to use STATIC IP address mode. STATIC ACCESS (NEW) For increased stability of the Wi-Fi connection in recommended that you select on your apple device access static. Under IP address select the box: Static. At this point, manually enter an IP address (eg 169.254.2.0) where the first two sets of numbers have to be 169.254 (identifying the network), while the latter two can vary to suit the user between 0 and 255 (for example, you can use the dongle number in the first and in the second zero). As netmask you should enter 255.255.0.0 . At this point by selecting the donlge the connection will take place in the manner defined above. Using different Dongle you will do the same for each 4
- 5. New Version 1.4 In very few cases, is possible that, with the operating system iOS 6.0 and 6.0.1, when turned on esa you can not still connect to the device. In this situation in the majority of cases it is sufficient to restart the device (iPhone, iPod, iPad) and repeat the normal connection procedures. To function properly esa is then necessary to select the option: Auto-Lock “Never”(da verificare sul cell) 5
- 6. 1 WARNINGS! • If the 3G connection is enabled you have to disable it because it can interfere with the WiFi connection. • Only one device at a time can access the Wi-Fi network, any device nearby that is already connected to the same networkof Astra board before making the connection can create a connection problem. If you want to use on a boat most apple devicesyou must have more dongle (can be connected in parallel to the on-board instrumentation) 1. The network connection is managed by the switch “Wi-Fi” which is set to 0 and white when it is not active. 3. Connecting the Esa Regatta app to the Esa Dongle 1 In esa software the management and status of Wi-Fi are included in the Home screen (page???). By accessing this screen you can manage the reception of data fron the Astra board and check the status. After completing all the procedure for the Wi-Fi service on your apple device and the network connection with Astra board is created you can enable receiving data from home screen . TheTo turn on,the central button of the switch. If 2. switch in press the part of the Home screen to the leftallows you to start receiving data connection is active the button same time provides the status of the communication, the from the Astra board and at the turns blue and displays a I. becomes blue if the connection is successful. 2 6
- 7. CONNECTION ISSUES The system automatically manages any temporary problems of connection making the reconnection autonomously. Le problematiche di connessione vengono indicate con una schermata di avviso, che consente anche, una volta risolto il problema, di effettuare un tentativo di riconnessione senza ritornare obbligatoriamente alla Home di esa(solo in casi particolari può essere necessario, permette il ripristino della connessione e del programma di navigazione). POSSIBLE CAUSES THAT GENERATE THE ERROR MESSAGE The Astra board is not powered: check the power supply and the red led on the board that must be switched on permanently. You have not performer the activation procedure of Wi-Fi: carry out the procedure and wait few seconds until the service is not active (the presence of the Wi-Fi icon in the upper left corner of the screen next to the time indicates that the device has completed the activation procedure of Wi-Fi connection). Disappearance of the WiFi icon when using esa(problem related even when the phone is placed in Standby): solve as above. The Wi-Fi network is active but you are connected to another network (also 3G):connect to the Astra network 7
- 8. RECEIVING DATA ISSUES The status of the receiving data is displayed in the navigation screen analysis from data reception icon located in the lower right of the screen, this data is generally more indicative of what is displayed by telephone. The icon has three different states: Optimal reception level: data arrive at constant intervals and there are no problems of any kind. Good reception level: data do not arrive at constant intervals; in this situation it is necessary to wait a few seconds, not move further away from the Astra board, to see if the receiving level data returns to optimal or degraded to insufficient. Insufficient reception level: in this situation it is necessary to move closer to the astra board to improve the connection signal. If it remains in this condition for an extended period of time receiving data may end. If the reception level is insufficient or ends an error message appears telling you to move closer to the Astra board and give the possibility of an automatic reconnection to the device. If the attempt is successful, the message disappears and the program resumes its normal operation. If appears the message of connection issue perform the procedure described above. 8
- 9. WARNING TRANSMITTER MUST NOT BE SHIELDED WITH “MATT” MATERIALS AT THE RADIO TRANSMISSION The materials that absorb more signal are iron, water and moist materials (also the human body), in boat a problem can arise from carbon fiber. In this case it is better not to put the dongle into rooms that are made from the materials mentioned, it is best that the antenna is outside (eg by placing the dongle on the shelf of the correspondence). The whip antenna emits radio frequency in all directions, but the intensity of the signal is stronger in the radial direction with respect to the stylus: keep the antenna of the Dongle oriented vertically.Provate eventualmente varie posizioni per ottenere il miglior segnale nella zona dove volete utilizzare il dispositivo Apple. If necessary try various positions in order to obtain the best signal in the area where you want to use the Apple device. 9