![1. Plug the AC/DC adapter (provided) into the 9VDC INPUT JACK (3) on the back of the receiver.
Then plug the power supply into
an AC outlet. Switch the POWER (1) to the ON position. The POWER ON LED (2) will now light
and the receiver is operational.
2. Rotate and extend ANTENNAS (4) fully, angled at 60 position as shown.
(5)
3. The 1/4 AUDIO OUTPUT JACK (5) provides a fixed, unbalanced MIC level audio output for
connection to your mixer with the
1/4 to 1/4 cord supplied. As when making any connection, make sure the mixing boards volume is
at the minimum level
before plugging in the receiver to avoid possible sound system damage. Use the VOLUME
CONTROLS (6) to adjust the volume.
(3)
OPERATION
HANDHELD MIC TRANSMITTER
1. Unscrew the BATTERY COMPARTMENT COVER (8) and remove. Insert a fresh 9V BATTERY
(9), observing correct polarity as marked,
and screw the cover back on to the microphone. To ensure proper battery contact, the cover must
be screwed on completely.
2. Turn on the handheld mic by sliding the OFF/ON SWITCH (10) to the ON position. The
BATTERY INDICATOR LED (11) will give a
single quick flash, indicating usable battery strength. In the case of a dead or low battery, the LED
will either not go on at all or will stay on
continuously, indicating that the battery should be replaced with a fresh one.
3. The microphone is now ready to use. The corresponding RX LED (7) on the DKW-3 receiver
should now be lit, indicating a received signal
from the transmitter. Adjust the VOLUME (6) control of the receiver clockwise to about 3/4 rotation,
until the volume level is comfortable for your
application.
[Note: Observe care in selecting P.A. volume, transmitter location and speaker placement so that
acoustic feedback (howling or screeching) will
be avoided.]
SPECIFICATION
OVERALL SYSTEM PERFORMANCE
Frequency Response: 80-14,000 Hz, +/-3dB
Dynamic Range: 95dB
Total Harmonic Distortion: <0.7%
RF Carrier Frequency Range: 170-216 MHz
Frequency Stability: +/- 0.005%, crystal controlled
Modulation: FM (F3E), +/-15KHz max.
Operating Range: 150 ft. typical-up to 300+ ft. line-of-sight](https://image.slidesharecdn.com/dkw3wireless-121012120820-phpapp01/85/Wireless-Amplification-2-320.jpg)
Wireless Amplification
- 1. The Nady DKW-3 is the perfect Wireless Solution entry level professional wireless, and delivers clear, transparent audio for a variety of singing and speech applications. Although offered at a breakthrough new low price for a professional wireless, this system is loaded with features: All the advantages and freedom of single channel wireless operation without cumbersome cords Easy to use simply plug in instead of your wired microphones Excellent high fidelity audio perfect for public speaking, karaoke/recreational singers, DJ's, and many other applications VHF (170-216MHz) operation for reliable, interference-free performance 150+ feet typical operating range up to 300+ feet line-of-sight Receiver Easy to use simply plug into your audio mixer or amplifier instead of your wired microphone. High-band VHF (170-216 MHz) operation for interference-free performance Advanced audio processing circuitry for a wide dynamic range (no overloading for loud inputs or background hiss during quiet use) Complete controls and connections for professional operation include front panel power ON/OFF switch, output volume control, Power ON LED indicator. Back panel 1/4 audio output jack and DC power input jack for supplied AC/DC adaptor. Special added circuitry eliminates transmitter on/off pop noise Handheld Microphone Transmitters Transmitter operates on a separate single frequency in the VHF 170-216MHz band Easy, convenient operation with on/off switch and low battery LED indicator which flashes once for unit "ON", and lights steady for low battery alert Features the Nady DM-20 unidirectional dynamic cartridge for optimum true sound, maximum feedback rejection and minimal handling noise Each transmitter operates up to 15 hours on a single 9V alkaline battery OPERATION RECEIVER DKW-3 WIRELESS MICROPHONE SYSTEM OPERATING INSTRUCTIONS (1) (2) (7) (6) (4)
- 2. 1. Plug the AC/DC adapter (provided) into the 9VDC INPUT JACK (3) on the back of the receiver. Then plug the power supply into an AC outlet. Switch the POWER (1) to the ON position. The POWER ON LED (2) will now light and the receiver is operational. 2. Rotate and extend ANTENNAS (4) fully, angled at 60 position as shown. (5) 3. The 1/4 AUDIO OUTPUT JACK (5) provides a fixed, unbalanced MIC level audio output for connection to your mixer with the 1/4 to 1/4 cord supplied. As when making any connection, make sure the mixing boards volume is at the minimum level before plugging in the receiver to avoid possible sound system damage. Use the VOLUME CONTROLS (6) to adjust the volume. (3) OPERATION HANDHELD MIC TRANSMITTER 1. Unscrew the BATTERY COMPARTMENT COVER (8) and remove. Insert a fresh 9V BATTERY (9), observing correct polarity as marked, and screw the cover back on to the microphone. To ensure proper battery contact, the cover must be screwed on completely. 2. Turn on the handheld mic by sliding the OFF/ON SWITCH (10) to the ON position. The BATTERY INDICATOR LED (11) will give a single quick flash, indicating usable battery strength. In the case of a dead or low battery, the LED will either not go on at all or will stay on continuously, indicating that the battery should be replaced with a fresh one. 3. The microphone is now ready to use. The corresponding RX LED (7) on the DKW-3 receiver should now be lit, indicating a received signal from the transmitter. Adjust the VOLUME (6) control of the receiver clockwise to about 3/4 rotation, until the volume level is comfortable for your application. [Note: Observe care in selecting P.A. volume, transmitter location and speaker placement so that acoustic feedback (howling or screeching) will be avoided.] SPECIFICATION OVERALL SYSTEM PERFORMANCE Frequency Response: 80-14,000 Hz, +/-3dB Dynamic Range: 95dB Total Harmonic Distortion: <0.7% RF Carrier Frequency Range: 170-216 MHz Frequency Stability: +/- 0.005%, crystal controlled Modulation: FM (F3E), +/-15KHz max. Operating Range: 150 ft. typical-up to 300+ ft. line-of-sight
- 3. TRANSMITTER Audio Input: Nady DM-20D unidirectional dynamic cartridge Controls: OFF/ON switch LED Indicator Unit: ON (single flash), Low Battery Alert (steady) RF Power Out: 50mW (Max. allowed by FCC) Harmonic & Spurious Emissions: >-40dB SERVICE Battery: 9V Alkaline Battery Life: Up to 15 hours Dimensions: 8.9 X 1.4 Dia. (22.6 X 3.5 cm) Weight (w/o battery): 5.4 oz. (151 g.) RECEIVER Controls: Power ON/OFF Connectors: 1/4 unbalanced audio out jack, 2.1mm barrel-type DC input jack LED Indicator: Power ON, Transmitter RF Dimensions: 8.2 X 5.3 X 1.75, (20.8 X 13.5 X 4.4 cm.) Weight: 16.1 oz. (451 g.) Power Requirements: 9V @ 120mA, nominal, AC/DC adapter supplied Antennas: Single 15 (38 cm), collapsible Specifications subject to change for product improvement purposes (U.S.) Should your Nady DKW-3 Wireless Microphone System require service, please contact the Nady Customer Service Department via telephone: (510) 652-2411 or e-mail: service@nady.com. (INTERNATIONAL) For service, please contact the Nady distributor in your country through the dealer from whom you purchased this product. The warranty card supplied with this system provides valuable warranty and service information. Store it in a safe place for future reference. Do not attempt to service this unit yourself as it will void your warranty. NADY SYSTEMS, INC. (9) (8) (10) (11) 6701 Shellmound Street Emeryville, CA 94608 Tel: 510.652.2411 Fax: 510.652.5075 www.nady.com