WIRELESS GESTURED CONTROLLED ROBOT USING ACCELEROMETER

WIRELESS GESTURE
CONTROLLED
ROBOT
USING ACCELEROMETER
NAME –LOKENDAR KUMAR PAL
BE.TECH (ECE)
COLLOGE-DEV BHOOMI INSTITUE OF
TECHNOLOGY,DEHRADUUN.

INTRODUCTION
LOKENDAR KUMAR PAL

 A Gesture Controlled robot is a kind of
robot which can be controlled by your hand
gestures not by old buttons.
 You just need to wear a small transmitting
device in your hand which included an
acceleration meter.

 This will transmit an appropriate command
to the robot so that it can do whatever we
want.
LOKENDAR KUMAR PAL

 The transmitting device included a
comparator IC for analog to digital
conversion and an encoder IC(HT12E)
which is use to encode the four bit data
and then it will transmit by an RF
Transmitter module.
 At the receiving end an RF Receiver
module receiver's the encoded data and
decode it by an decoder IC(HT12D).
 This data is then processed by a
microcontroller (ATMEGA 16) and finally
our motor driver to control the motor's
LOKENDAR KUMAR PAL

Robot
Gesture device
LOKENDAR KUMAR PAL

 As we can see in the images one is robot
and the another is to transmit the gesture
data to robot.
 Now its time to break the task in different
module's to make the task easy and
simple any Project become easy or error
free if it is done in different modules. As
our project is already divided into two
different part transmitter and receiver.
LOKENDAR KUMAR PAL

CIRCUIT DIAGRAM FOR RECIEVER
A
T
M
E
G
A
1
6
LOKENDAR KUMAR PAL

CIRCUIT DIAGRAM FOR TRANSMITER
LOKENDAR KUMAR PAL

CIRCUIT DESCRIPTION
 Transmitter device or Gesture device: This
part contain four module in it--
 1- Accelerometer
 2- Comparator
 3- Encoder(HT12E)
 4- RF Transmitter
LOKENDAR KUMAR PAL

Accelerometer:-
 An Accelerometer is a kind
of sensor which gives an
analog data while moving
in X,Y,Z direction or may
be X,Y direction only
depends on the type of the
sensor.
 Here is a small image of an
Accelerometer shown. We
can see in the image that
their are some arrow
showing if we tilt these
sensor's in that direction
then the data at that
corresponding pin will
change in the analog form. LOKENDAR KUMAR PAL

 A Accelerometer have 6 pins-
 1- VDD- We will give the +5volt to this pin
 2- GND- We simply connect this pin to the
ground for biasing.
 3- X- On this pin we will receive the analog
data for x direction movement.
 4- Y- On this pin we will receive the analog
data for y direction movement.
 5- Z- On this pin we will receive the analog
data for z direction movement.
 6- ST- this pin is use to set the sensitivity of
the accelerometer 1.5g/2g/3g/4g.
LOKENDAR KUMAR PAL

COMPARATOR
 For the purpose to change the
analog voltage into digital we use
comparator which compare that
analog voltage to a reference
voltage and give a particular high
or low voltage.
 LM324 IC The figure shown here is
comparator IC. The pin 1,7,8 and
14 are use to give out put to the
microcontroller. We should connect
a reference voltage to the -ve
terminal for high output when input
is high(+ve terminal for high output
when input is low) from the LM324
IC.
 In this circuit we compare the data
from x with two terminal one for
positive x direction and negative x
direction and same for y direction.
 LOKENDAR KUMAR PAL

Encoder(HT12E IC):-
 The HT12E is an 4bit encoder which
encode the input data applied on it .The
pin description of the HT12E is shown in
the figure .
 Pin (1 to 8) A0-A7 known as address bits
so we do not need to consider them. Pin
no (9 and 18) are use to bias the IC as
pin-18 as VCC and pin-9 as GND Pin - 17
is connected to the rf transmitter module
Pin.
 Pin-16 and pin-15 are connected by an
Osc resistor known as Roscc(1.1
Mohm).Pin-14 is connected to ground to
enable the transmit.
 Pin-13 to pin-10 are known as AD0 to
AD3 those having the 4bit data which is
required to transmit.
LOKENDAR KUMAR PAL

RF Transmitter Module(TX):-
 The transmitter module is
working on the frequency of
433MHz and is easily available
in the market at the cost of
250rs .
 The vcc pin is connected to
the +terminal in the circuit.
 The data pin is connected to
the HT12E(pin no-17) that is
transmitted or we can say
that encoded data.
 The next pin is shown in
figure is GND that is
connected to the ground
terminal.
 Now the last pin ANT this is
connected to a small wire as
an antenna.
LOKENDAR KUMAR PAL

Receiver or Robot
 This part contain four module--
 1. Receiver
 2. Decoder(HT12D)
 3. Process(microcontroller 8051)
 4. Actuator (Motor driver L293D)
LOKENDAR KUMAR PAL

RF Receiver Module(RX):-
 The RF receiver module will
receive the data which is
transferred by the gesture
device. It is also working as
similar to the transmitter
module.
 Connect the +vcc pin to the
5volt terminal Connect the
ground pin to the ground
terminal.
 The data pin is then connected to
the HT12D (pin-14). So that we
can get the decoded 4 bit data
Connect the +vcc pin to the
5volt terminal Connect the
ground pin to the ground
terminal.
 The data pin is then connected to
the HT12D (pin-14). So that we
can get the decoded 4 bit data
LOKENDAR KUMAR PAL

Decoder (HT12D):-
 In a very simple way we can say that an
HT12D converts that serial data into
parallel which is received by the rf
receiver module. The input data is
decoded when no error or unmatched
codes are found. A valid transmission in
indicated by a high signal at VT pin that is
pin no 17.
 Pin 18 : It is use to give the +vcc or
biasing to the IC HT12D this pin is
connected with the +5 volt.
 Pin 17 : It is the valid transmission pin it
will high when the transmission is ok so
that we connected this pin to an led for
indication.
 Pin 16-15: we connect these two pin
directly by a 51k resistor.
 Pin 14 : This pin is connected with the rf
receiver module data pin to receiving the
 serial data.
 Pin 10-13: These pins are data pin which
is transferred by the gesture module LOKENDAR KUMAR PAL

Process (Microcontroller ATMEGA 16):
 The processing is the most important part of
the robot. Till now we get the data from the
decoder now based on that data we have to
make some decision so here the role of
microcontroller is coming up. We use an
ATMEGA16 microcontroller for our circuit to give
them a decision capability. Our microcontroller
is made up by Atmel the product name is
ATMEGA 16.
LOKENDAR KUMAR PAL

 The basic circuit to
initialize the
microcontroller is
 we use the port 1 as an
input port and port 2
as an output port.
 so the Data from the
decoder will connect
with pin 1,2,3,4 and
motor should be
 connect with pin
21,22,23,24.
 For forward the data to
the Port2 is 0a or for
backward it is 05 then
for left its 02 and
 for right it is 08.
LOKENDAR KUMAR PAL

ACTUATOR'S(L293D):
 The Actuator's are those devices which actually
gives the movement or to do a task like motor's.
 In the real world their are various types of
motor's available which works on different
voltages.
 So we need motor driver for running them
through the controller. To get interface between
motor and microcontroller . We use L293D motor
driver IC in our circuit.
 Motor driver as in the circuit a 2 pin male
connector is connected to the pin 8 this will
provide the operating voltage for the motor like
if we want to run, our voltage on 12 volt. so we
just have to connec12volt power source
LOKENDAR KUMAR PAL

SOFTWARE USED:
 AVR Studio 4.:- For programming
 Proteus.:- for simulation
LOKENDAR KUMAR PAL

APPLICATION:
 Explosive Material Detection for Police,
Military.
 To search mines ,survey in dangerous area
where man can’t travel.
 To make mobile BOM to damage enemy
tanks,bunkars etc. for military purpose etc.
LOKENDAR KUMAR PAL

FUTURE SCOPE:
 We can add explosive material Detector to
track the path of Army.
 We can Drive our Robot in Heavy traffic from
anywhere using our Remote.
 We can add webcam to see the traffic in our
laptop.
LOKENDAR KUMAR PAL

THANK YOU !!
LOKENDAR KUMAR PAL

WIRELESS GESTURED CONTROLLED ROBOT USING ACCELEROMETER

More Related Content

What's hot (20)

Viewers also liked (20)

Similar to WIRELESS GESTURED CONTROLLED ROBOT USING ACCELEROMETER (20)

Recently uploaded (20)

WIRELESS GESTURED CONTROLLED ROBOT USING ACCELEROMETER