Ymt dvr operation manual

The series DVR is designed specially for security and
surveillance field which is an outstanding digital surveillance
product. It introduces embedded LINUX operating system which is
more stable. It introduces standard H.264mp video compressed
format and G.711A audio compressed format which insures the
high quality image and low error coding ratio. Strong network
services greatly enhance the network data transmission capacity
and remote control capabilities.
The First Part: Basic Operation
1 Basic Installation
1.1 Hard Disk Installation
For the first use，please install the hard disk.
Full Function series DVR support 2 Sata hard disks, and Simple
Function series DVR support 1 Sata hard disk.
Note: DVR can run and monitor normally without hard disk,
while it can’t record and playback.
1.2 Mouse Connection
Full Function series DVR has 1 USB at back panel and 1 USB at
front panel,the 2 USB could be used for mouse,Flash stick,3G&WIFI
module,movable HDD and USB DVR-RW.
Simple Function series has two USB at back panel for mouse and
flask stick
2 Turn on
Plug the power supply and turn on the power supply switch.
Power supply indicator light shining indicates turning on the video
recorder. After finishing the startup you will hear a beep, and the
default setting of video output is multiple-window output mode.
Note: Restart the power after the abnormal power off, DVR
will automatically recover the state before power off.
3 Turn off
There are two methods to turn off the DVR which are soft switch
and hard switch. Entering [Main menu] and choosing [Logout] in
the [turn off the system] option is called soft switch. Pressing the

power supply switch is called hard switch.
Note: The setting information must be saved before
replacing the battery otherwise information will lose.
4 Login
When the DVR boots up,user must login and the system
provides the corresponding functions with the user purview. There
are two user settings which are admin, and guest; and they have
no passwords. “Admin” is the super user purview; “Guest” is the
common user purview.
Password protection: If the password is continuous wrong
three times, the alarm will start. If the password is continuous
wrong five times, the account will be locked. (Through reboot or
after half an hour, the account will be unlocked automatically).
Picture1 Login
For your system security, please modify your password after
first login.
5 Preview
Login normally and choose the multi-menu preview status.
The system date, time and channel name are shown in each
viewing window. The surveillance video and the alarm status are
shown in each window.
1 Recording status 3 Video loss
2 Motion detect 4 Camera lock

Table1 Preview icon
6 Recording Config
Set the recording parameters in the surveillance channel. You
can enter [Main Menu]> [Record]> [Record Config] to set. The
system’s default set is 24 hours continuous recording.
Note: There is at least one read-write hard disk if the DVR
records normally.
Picture2 Record Config
【Channel】Choose the corresponding channel number to set the
channel. Choose the “all” option to set the entire channels.
【Redundancy】Choose the recording file and backup in two hard
disks. The one is read-write disk, another is redundant disk.
【 Length 】 Set the time length of each video file. 60minutes is
default length.
【Prerecord】Record 1-30 seconds before the action. (file length is
decided by the code stream)
【Record Mode】Setvideostate:configuration,manualandstop.
Schedule ： Record according to the set video type (regular,
detect and alarm)and time section.
Manual：Click the “all” button and make the corresponding
channel recording no matter it is in any state.
Stop：Click the “stop” button and make the according channel
stop recording no matter it is in any state.

【 Period 】 Set the time section of common recording, The
recording will start only in the set range.
【Recording Type】Set recording type: regular, detection or alarm.
regular：Perform the regular recording in the set time section.
The video file type is “R”.
detect：Trigger the “motion detect”, “camera mask” or “video
loss” signal. When above alarm is set as opening
recording, the “detection recording” state is on. The
video file type is “M”.
alarm：Trigger the external alarm signal in the set time section.
When above alarm is set as opening recording, the
“detection recording” state is on. The video file type is
“A”.
7.Snapshot Storage.(partial devices supported)
Setup snapshot parameters for different channels.At first time
it's set for 24hours snapshot continuously, pls go to Main
Menu->Record->Snapshot Storage for appropriate settings.
Note:If normal snapshot storage,pls setup Snap at
MainMenu->Advanced->HDD Manage->Snapshot.
Picture3 Snapshot Storage
8 Video Playback
There are two methods for you to play the video files in the

hard disk.
1. In the desktop shortcut menu.
2. Main Menu>Record>Playback.
Note: The hard disk that saves the video files must be set as
read-write or read-only state.
Picture4 Video Playback
1.File option 2.File information 3. File searching
4.File Backup 5. Operation hint 6.Playback control
【File option】Choose the file to playback/backup.
【File information】Start time,end time and size.
Note: Thestoragemustbelargeenoughbeforethefilebackup.
【 File searching 】 Search the file according to the searching
parameter.
【File Backup】Backup files from HDD
【operation hint】Display the function of the cursor place.
【 playback control 】 Refer to the following sheet for more
information.

Table2 Playback control key
Note: Frame by frame playback is only performed in the "pause"
playback state.
Special functions:
Accurate playback:Input time (h/m/s) in the time column
and then click playback.
Local zoom:When the system is in single-window full-screen
playback mode, you can drag your mouse in the screen to select a
section and then left click mouse to realize local zoom. You can
right click mouse to exit.
9 Network Setup
Picture5 Network Setup

Doing network setup through Main Menu>System>Network
【IP address】Set the IP address. Default: 192.168.1.10.
【Subnet Mask】Set the subnet mask code.
Default: 255.255.255.0.
【Gateway】Set the default gateway. Default: 192.168.1.1.
Make the equipment’s IP address and the router in the same
network segment. For example, the router IP address is
192.168.1.1, and the subnet mask is 255.255.255.0. According to
the default setup, generally the default gateway is the router IP
address, so enter IP address 192.168.1.10 in the IE browser to
achieve visiting LAN equipment such as operating image
surveillance in the public network remote access equipment for
monitoring. Detail setup refer to “Network setup reference”.
10 Alarm Setup
Picture 6 Motion Detection
Motion detection setup. Set DVR equipment making it alarm,
linkage record and make the PTZ turn to preset position when
there is a moving object in designated areas during Monday to
Friday.
Step1. Choose【Main Menu】>【Alarm】>【Motion Detect】，
then enter the setup interface;
Step2. Choose one channel and adjust sensitivity level, then

set the time period of alarm surveillance. Set the monitor
area(click the “set” button, choose the areas you want, and the
“default” means choose all areas, then righclick to choose "up
window".
Step3. When at alarm state, the DVR can take linkage
measures. Alarm output, recording, tour, PTZ activation,
snapshot,show message, sending email and buzzer.
Step4. Set other channels alarm parameter following step 2
and step 3.
Note: video block, video loss and alarm input’s setup method are
similar with motion detection.
10 PTZ Control
Through the following steps doing easy PTZ operations.
Step1. Set basic parameter such as channel and protocol.
【Main Menu】>【System】>【PTZ Config】
Step2. At the state of menu preview, enter the PTZ operation
menu.
Step3.One is "rightclick" mouse, choose the “PTZ control”
and doing the PTZ general operation. The other method is
"rightclick" mouse, choose “High Speed PTZ”. Control the left
button and move it to control the PTZ direction directly. Use the
mouse wheel to zoom in/out the controlled camera.
The Second Part: Remote Control
1 Network Connection
Before web operation,you need to connect the equipment wit
h internet.
Step1.Connect the equipment with the internet correctly.
Step2.Set LAN following to the ninth term Network Setup in r
eference manuals first part.
Step3.when Lan is connected,it needs to set up port mapping f
or public network access.
Step4.DDNS Application.You can apply for DDNS in the http://
www.3322.org/ and http://www.oray.com/
Step5.DDNS Setup.Make sure to fill the right info in the Main
Menu->System->NetService->DDNS
Note:The device must be in the same network with PC,if can

not connect,pls check the device IP if it works fine.
2. Remote Monitoring
After connecting the network, two kinds of methods can be
used for remote monitoring which are client software and common
browser.Client software(CMS) is professional software used in
multi-equipments monitoring, which is safe, convenient and stable.
It is the better one that we advise customers use it. And the
browser comes with system such as IE browser.
2.1 Client software
CMS software is used in a computer, and manipulates several
DVR at the same time.
Step1. Please take CD out of the accessory box, then copy
CMS installed software in it.
Step2.After installing this software at the local PC, then open
the operation system as in picture 6,Enter the add device interface
through【System】>【Device Manager】>【Add area/device】, and
enter DVR information which is needed manipulating following the
prompts, in that way, you can manipulate any specified equipment.
And the method is the same with web manipulation’s.
Step3. You can add several DVR more to do monitor operation
if you repeat this operation.
Picture 7 CMS Interface

2.2 WEB
After the network connecting, using the browser comes with
computer login DVR to do remote monitoring.
Step1. install the plug. Open the disk, then get
General_IE_V2.0.0.35_20111222.exe and install.
Step2. Connect the equipment. Open web browser, then
enter IP address on the address bar of the equipment. For example,
the IP address of the equipment is 10.6.0.114, and then you should
enter http://10.6.0.114 on the address bar to connect.
Pop up as follows interface after connecting successfully.
Note: when first login,see below picture
Picture 8 Web Login Interface
Step3. Login. Enter user’s name and password, the default
AdministratorUserIDisadmin,andthepasswordisadmin.Theusershould
change the administrator’s password timely after loginning in.(If choose
"Local Area Network",it's Main streams,if "wide Area Network",it's Sub
streams.)
You will see as follows interface after loginning in.

Picture 9 WEB operation interface
3. Basic Web Operation
Do web operation in picture 8 web operation interface
1) Screen Split
Choose image preview mode;
2) Playback
Enter playback mode, which supports multi-channel
playing back simultaneously.
3) Log
Display log information；
4) Local Config
Alarm and System setting
5) Channel operation
Open the videos. Left click and choose a window in the left,
and choose the corresponding channel in the right, then double click
the video.Open the second channel’s video, choose the left window,
thenselectthecorrespondingchannelin theright,afterthen,double

click the video. Opening other channels is the same way. If you have
chosen the window of opened video, then open other channels in
the right, the system will close all the channels and open new
channel. Customers can adjust image mode upon opened video
channels.
Close the channel. Rightclick mouse at the channels which are
needed to close. Orchoose to close all the windows to close opened
videochannels.
The Third Part: Special Function
This series become more personalization design and visualization
operation press key,local enlarge at any areas in preview
interface,timing start up and shut down,FTP upload,3G&WIFI and
so on.Now let's introduce Encode,Multi channels playback and
mobile monitor setup.
1 Coding Config
DVR achieves the functions such as high quality playback and
remote monitoring by coding parameter config.
Picture 10 Encode setup

1.1 Encode setup for every channel
Note: Only part of DVR mode support resolution switch.
Step1. Local operation through 【Main Menu】>【System】>
【Encode】（remote setup click right mouse and choose “config” in
【System】>【Encode】）.
Step2. Choose channel 1, set the resolution as D1 (25fps,
1536Kb/s)
Step3. Choose channel 2, set the resolution as CIF (25fps, 512Kb/s).
Clickrightmouseorchoose“Advanced”thenclick“Copy”button.
Step4. Choose channel 3, click the right button or choose the
local “Advanced”, then choose “Stick”. Channel 4’s operation is the
same with channel 3.
Step5. Click “save”, then exit.
Note: standard parameter between resolution and Kb/s.
Resolution Kb/S
D1 512~2560
HD1 384~2048kbps
CIF 64~1024kbps
QCIF 64~512kbps
1.2 Extra Stream Setup
Extrastreamisusedforremoteclientmonitorandmobilemonitorarea.
Step1. Enable extra stream
Step2. Set frame rate and bit rates,operation way is the same
as main stream.
2 Multi-channel Playback Simultaneously
DVR introduces the newest combination coding technique to
achieve videos of all channels play simultaneously.
4 channel DVR can support 4channels playback
simultaneously,8 channel DVR can support 8channels playback
simultaneously,channel number can be free chosen.

Picture11 Video Playback
Step1. Set every channel’s encode parameter by 【 Main
Menu】>【Record】>【Encode】.
Step2. Enter video playback interface, click Search button.
Step3. Choose File Type and All and time period, then click OK
in Search Condition interface.
Step4. Choose the record file, then click Play or double click
the file to playback in playback interface.
3 Multi-channel Real-time Monitor remotely
Introduce extra-stream techniques to achieve multi-channel
remote monitoring simultaneously in the condition of narrow
band(poor network speed)

Picture12 CMS Interface
Step1. Enable extra streams(MainMenu->System->Encode)
Step2. Open CMS, and then login.
Step3.After add devices,rightclick device name to select
"Connectall video(Main stream)"
4 Mobile Monitoring
It introduces extra stream techniques when mobile
monitoring,support channels switch(eg. Windows mobile)
Step1. DVR config,go to MainMenu->System->Encode->
Extra Stream,enable it.
Step2. Setup mobile monitor, go to MainMenu->System->
NetService->Mobile Monitor,choose "Enable"
Note: Pls map the mobile monitor port in the router
first,then you can use mobile to visit it.
Step3. Intall the corresponding mobile monitoring software
through CD (Software->Mobile Monitor->MEYE->
MEYE_WM.cab)
Step4. After successfully installing the software,finding and
running "eg.windows mobile-moveeye" software through
[start]->[procedure] in the mobile,see picture 14

Picture13 mobile client software Interface
Step5.Mobile setup.Click "setting" button at the right corner,then
go to below picture 15.
picture 14 mobile client software setting
User name: login name of DVR
Password: password of DVR
Server: IP address or domain name of DVR
Port: mobile monitor port of DVR,pls refer to Step 2.
Auto Connect:If select it,then it will auto connect to the DVR and
auto display cameras.
Note:DVR need to be connect to public net when mobile monitor
Similar setup between different operation system:
Symbian S60 the 3rd operation system mobile monitoring

client software: MEYE_SB_S60_3rd.sisx
Symbian S60 the 5th operation system mobile monitoring
client software: MEYE_SB_S60_5th.sisx
Android mobile monitoring client
software:MEYE_Android.cab
Blackberry mobile monitoring client software:MEYE_RIM.cod
Iphone mobile monitoring software: use mobile to search
"vMeye" in the appstore and install it online.
5 Flexible File Storage and Backup
DVR introduces several unique storage and backup techniques to
achieve multiple modes storage and backup.
Real-time storage
Redundant storage. DVR introduces RAD 1 storage technique
to achieve two hard disks storing simultaneously and mutual
backup.
USB HDD and movable hard disk. DVR introduces the storage
technique, supporting video files which are real-time written in
storage devices.
DVD-RW. DVR introduces the newest real-time storage
technique, supporting video file which are burnt real-time to CD.
Real-time remote storage. DVR supports video files real-time
storing to computer devices(Disk C/D/E/F) at the remote client.
File download
Using U disk and movable hard disk download at local device,
DVR supports the chosen file are high-speed backup to the storage
devices.
DVD-RW. DVR supports the chosen video file are burnt and
stored as CD.
Network high-speed download. DVR supports high-speed
down loading the chosen file at remote client.

Appendix 1. Remote controller operation
Serialnumber Name Function
1 Multi-channels
button
Multi-channels preview
2 Number button Password input/number
input/ channel switch
3 【Esc】 Back to up window
4 Direction button Direction and OK button
5 Playback
operate
Playback Basic operation
6 Record control Enter into record menu
7 Remote
controller
Input the number of DVR
to control it
8 FN Assistant function

Appendix 2.Mouse operation
*Take right hand as an example
Operation Function
Double left
click
Double click one item in the file list to
playback the video
Double click the playback video to zoom
in or out the screen
Double click the channel to make it full
screen display in preview
double click again to resume the
multi-channel display
Left click Choose according option in the menu
Right click
Pop desktop shortcut menu in preview
state
Current shortcut menu in the menu
Wheel button
Add or subtract number value in the
number setting
Switch the items in the combo box
Page up or down in the list
Move mouse
Choose the widget or move the item in
the widget
Drag mouse
Set the motion detect area
Set the cover area

PRODUCT WARRANTY CARD
All the products sold are covered by 12months warranty from
the date of invoice.
Warranty instructions：
1. Please contact us when the product is caused by its own
fault within 1year warranty.
2. Please mail us your written warranty card as soon as
possible after purchasing our products so that we can repair or
replace this product to its original operation condition for free. Or
the company will not deal with it.
3. Please write the truth information on the warranty card.
4. Paid for repairing as follows:
A: Equipment failure caused by human operation
B: Equipment failure caused by not conforming to the using
environment
C: No warranty card
D: Warranty expired
Warranty card information:
Product model Product serial number
Purchasing time
User name Contact person
Telephone
Distributor Name Contact person
Telephone
Note：Please keep the warranty card for the better service.
www.cctv-auckland.com

Ymt dvr operation manual

More Related Content

What's hot (20)

Viewers also liked (20)

Similar to Ymt dvr operation manual (20)

More from DishHD Asia (20)

Recently uploaded (20)

Ymt dvr operation manual