01 e part1

Copyright © United Nations, 2009. All rights reserved

PART 1

GENERAL PROVISIONS,

DEFINITIONS, TRAINING

AND SECURITY

- 19 -


CHAPTER 1.1

GENERAL PROVISIONS

Introductory notes

NOTE 1: Recommendations on Tests and Criteria, which are incorporated by reference into certain
provisions of these Regulations, are published as a separate Manual (“Recommendations on the Transport
of Dangerous Goods, Manual of Tests and Criteria”) (ST/SG/AC.10/11/Rev.5), the contents of which are:

Part I: Classification procedures, test methods and criteria relating to explosives of Class 1

Part II: Classification procedures, test methods and criteria relating to self-reactive
substances of Division 4.1 and organic peroxides of Division 5.2

Part III: Classification procedures, test methods and criteria relating to Class 2, Class 3,
Class 4, Division 5.1, Class 8 and Class 9

Part IV: Test methods concerning transport equipment

Appendices: Information common to a number of different types of tests and national
contacts for test details.

NOTE 2: Part III of the Manual of Tests and Criteria contains some classification procedures, test
methods and criteria which are also given in these Regulations.

1.1.1 Scope and application

1.1.1.1 These Regulations prescribe detailed requirements applicable to the transport of dangerous
goods. Except as otherwise provided in these Regulations, no person may offer or accept dangerous goods
for transport unless those goods are properly classified, packaged, marked, labelled, placarded, described and
certified on a transport document, and otherwise in a condition for transport as required by these
Regulations.

1.1.1.2 These Regulations do not apply to the transport of:

(a) Dangerous goods that are required for the propulsion of the means of transport or the
operation of its specialised equipment during transport (e.g. refrigeration units) or that
are required in accordance with the operating regulations (e.g. fire extinguishers); and

(b) Dangerous goods, packaged for retail sale, that are carried by individuals for their own
use.

NOTE 1: Specific modal provisions for the transport of dangerous goods as well as derogations from
these general requirements can be found in the modal regulations.

NOTE 2: Certain special provisions of Chapter 3.3 also indicate substances and articles which are not
subject to these Regulations.

1.1.1.3 In certain parts of these Regulations, a particular action is prescribed, but the responsibility
for carrying out the action is not specifically assigned to any particular person. Such responsibility may vary
according to the laws and customs of different countries and the international conventions into which these
countries have entered. For the purposes of these Regulations, it is not necessary to make this assignment,
but only to identify the action itself. It remains the prerogative of each government to assign this
responsibility.

- 21 -


1.1.1.4 In the transport of dangerous goods, the safety of persons and protection of property and the
environment are assured when these Regulations are complied with. Confidence in this regard is achieved
through quality assurance and compliance assurance programmes.

1.1.1.5 Exceptions for dangerous goods packed in limited quantities

Certain dangerous goods packed in limited quantities are exempted from certain
requirements of these regulations subject to the conditions laid down in Chapter 3.4.

1.1.1.6 Transport of dangerous goods by post

In accordance with the Universal Postal Union Convention, dangerous goods as defined in
these Regulations, with the exception of those listed below, are not permitted in mail transported
internationally. Appropriate national authorities should ensure that provisions are complied with in relation
to the international transport of dangerous goods. The following dangerous goods may be acceptable in
international mail subject to the provisions of the appropriate national authorities:

(a) Infectious substances, assigned to Category B (UN 3373) only, and solid carbon
dioxide (dry ice) when used as a refrigerant for UN 3373; and

(b) Radioactive material in an excepted package conforming to the requirements
of 1.5.1.5, the activity of which does not exceed one tenth of that listed in
Table 2.7.2.4.1.2.

For international movement by post additional requirements as prescribed by the Acts of the
Universal Postal Union apply.

NOTE: The Acts of the Universal Postal Union do not apply to the domestic transport of dangerous
goods by mail. Domestic transport of dangerous goods in the mail is subject to the provisions of the
appropriate national authorities.

1.1.2 Dangerous goods forbidden from transport

1.1.2.1 Unless provided otherwise by these Regulations, the following are forbidden from transport:

Any substance or article which, as presented for transport, is liable to explode, dangerously
react, produce a flame or dangerous evolution of heat or dangerous emission of toxic, corrosive or flammable
gases or vapours under normal conditions of transport.

- 22 -


CHAPTER 1.2

DEFINITIONS AND UNITS OF MEASUREMENT

1.2.1 Definitions

NOTE: This Chapter provides definitions of general applicability that are used throughout these
Regulations. Additional definitions of a highly specific nature (e.g., terms relating to construction of
intermediate bulk containers or portable tanks) are presented in the relevant chapters.

For the purposes of these Regulations:

Aerosol or aerosol dispenser means a non-refillable receptacle meeting the requirements of 6.2.4, made of
metal, glass or plastics and containing a gas, compressed, liquefied or dissolved under pressure, with or
without a liquid, paste or powder, and fitted with a release device allowing the contents to be ejected as solid
or liquid particles in suspension in a gas, as a foam, paste or powder or in a liquid state or in a gaseous state;

Aircraft

Cargo aircraft means any aircraft, other than a passenger aircraft, which is carrying goods or
property;

Passenger aircraft means an aircraft that carries any person other than a crew member, a
carrier's employee in an official capacity, an authorized representative of an appropriate
national authority, or a person accompanying a consignment or other cargo;

Alternative arrangement means an approval granted by the competent authority for a portable tank or MEGC
that has been designed, constructed or tested to technical requirements or testing methods other than those
specified in these regulations (see, for instance, 6.7.5.11.1);

Animal material means animal carcasses, animal body parts, or animal foodstuffs;

Approval

Multilateral approval, for the transport of Class 7 material, means approval by the relevant
competent authority of the country of origin of the design or shipment, as applicable, and
also, where the consignment is to be transported through or into any other country, approval
by the competent authority of that country;

Unilateral approval, for the transport of Class 7 material, means an approval of a design
which is required to be given by the competent authority of the country of origin of the
design only;

ASTM means the American Society for Testing and Materials (ASTM International, 100 Barr Harbor Drive,
PO Box C700, West Conshohocken, PA, 19428-2959, United States of America);

Bag means a flexible packaging made of paper, plastics film, textiles, woven material or other suitable
materials;

Box means a packaging with complete rectangular or polygonal faces, made of metal, wood, plywood,
reconstituted wood, fibreboard, plastics or other suitable material. Small holes for purposes such as ease of
handling or opening, or to meet classification requirements, are permitted as long as they do not compromise
the integrity of the packaging during transport;

- 23 -


Bulk container means a containment system (including any liner or coating) intended for the transport of
solid substances which is in direct contact with the containment system. Packagings, intermediate bulk
containers (IBCs), large packagings and portable tanks are not included.

A bulk container is:

- of a permanent character and accordingly strong enough to be suitable for repeated
use;

- specially designed to facilitate the transport of goods by one or more means of
transport without intermediate reloading;

- fitted with devices permitting its ready handling;

- of a capacity of not less than 1.0 m3.

Examples of bulk containers are freight containers, offshore bulk containers, skips, bulk
bins, swap bodies, trough-shaped containers, roller containers, load compartments of vehicles;

Bundle of cylinders means an assembly of cylinders that are fastened together and which are interconnected
by a manifold and transported as a unit. The total water capacity shall not exceed 3 000 litres except that
bundles intended for the transport of gases of Division 2.3 shall be limited to 1 000 litres water capacity;

Cargo transport unit means a road transport tank or freight vehicle, a railway transport tank or freight
wagon, a multimodal freight container or portable tank, or a MEGC;

Carrier means any person, organization or government undertaking the transport of dangerous goods by any
means of transport. The term includes both carriers for hire or reward (known as common or contract carriers
in some countries) and carriers on own account (known as private carriers in some countries);

CGA means the Compressed Gas Association (CGA, 4221 Walney Road, 5th Floor, Chantilly VA 20151-
2923, United States of America);

Closed cargo transport unit means a cargo transport unit which totally encloses the contents by permanent
structures with complete and rigid surfaces. Cargo transport units with fabric sides or tops are not considered
closed cargo transport units;

Closure means a device which close an opening in a receptacle;

Combination packaging means a combination of packagings for transport purposes, consisting of one or
more inner packagings secured in an outer packaging in accordance with 4.1.1.5;

Competent authority means any body or authority designated or otherwise recognized as such for any
purpose in connection with these Regulations;

Compliance assurance means a systematic programme of measures applied by a competent authority which
is aimed at ensuring that the provisions of these Regulations are met in practice;

Composite packaging means a packaging consisting of an outer packaging and an inner receptacle so
constructed that the inner receptacle and the outer packaging form an integral packaging. Once assembled it
remains thereafter an integrated single unit; it is filled, stored, transported and emptied as such;

Confinement system, for the transport of Class 7 material, means the assembly of fissile material and
packaging components specified by the designer and agreed to by the competent authority as intended to
preserve criticality safety;

- 24 -


Consignee means any person, organization or government which is entitled to take delivery of a
consignment;

Consignment means any package or packages, or load of dangerous goods, presented by a consignor for
transport;

Consignor means any person, organization or government which prepares a consignment for transport;

Containment system, for the transport of Class 7 material, means the assembly of components of the
packaging specified by the designer as intended to retain the radioactive material during transport;

Conveyance means

(a) For transport by road or rail: any vehicle;

(b) For transport by water: any vessel, or any hold, compartment, or defined deck area of
a vessel; and

(c) For transport by air: any aircraft;

Crate means an outer packaging with incomplete surfaces;

Criticality safety index (CSI) assigned to a package, overpack or freight container containing fissile material,
for the transport of Class 7 material, means a number which is used to provide control over the accumulation
of packages, overpacks or freight containers containing fissile material;

Critical temperature means the temperature above which the substance cannot exist in the liquid state;

Cryogenic receptacle means a transportable thermally insulated receptacle for refrigerated liquefied gases, of
a water capacity of not more than 1 000 litres;

Cylinder means a transportable pressure receptacle of a water capacity not exceeding 150 litres;

Defined deck area means the area of the weather deck of a vessel, or of a vehicle deck of a roll-on/roll-off
ship or a ferry, which is allocated for the stowage of dangerous goods;

Design, for the transport of Class 7 material, means the description of special form radioactive material, low
dispersible radioactive material, package or packaging which enables such an item to be fully identified. The
description may include specifications, engineering drawings, reports demonstrating compliance with
regulatory requirements, and other relevant documentation;

Drum means a flat-ended or convex-ended cylindrical packaging made of metal, fibreboard, plastics,
plywood or other suitable materials. This definition also includes packagings of other shapes e.g. round
taper-necked packagings, or pail-shaped packagings. Wooden barrels or jerricans are not covered by this
definition;

Elevated temperature substance means a substance which is transported or offered for transport:
- in the liquid state at a temperature at or above 100 °C;
- in the liquid state with a flashpoint above 60 °C and which is intentionally heated to a
temperature above its flashpoint; or
- in a solid state and at a temperature at or above 240 °C;

EN (standard) means a European standard published by the European Committee for Standardization (CEN)
(CEN – 36 rue de Stassart, B-1050 Brussels, Belgium);
- 25 -


Exclusive use, for the transport of Class 7 material, means the sole use, by a single consignor, of a
conveyance or of a large freight container, in respect of which all initial, intermediate and final loading and
unloading is carried out in accordance with the directions of the consignor or consignee;

Filling ratio means the ratio of the mass of gas to the mass of water at 15 °C that would fill completely a
pressure receptacle fitted ready for use;

Freight container means an article of transport equipment that is of a permanent character and accordingly
strong enough to be suitable for repeated use; specially designed to facilitate the transport of goods, by one
or other modes of transport, without intermediate reloading: designed to be secured and /or readily handled,
having fittings for these purposes, and approved in accordance with the International Convention for Safe
Containers (CSC), 1972, as amended. The term “freight container” includes neither vehicle nor packaging.
However a freight container that is carried on a chassis is included. For freight containers for the transport of
Class 7 material, a freight container may be used as a packaging.

A small freight container is that which has either any overall outer dimension less
than 1.5 m, or an internal volume of not more than 3 m3. Any other freight container is considered to be a
large freight container;

Fuel cell means an electrochemical device that converts the chemical energy of a fuel to electrical energy,
heat and reaction products;

Fuel cell engine means a device used to power equipment and which consists of a fuel cell and its fuel
supply, whether integrated with or separate from the fuel cell, and includes all appurtenances necessary to
fulfil its function;

GHS means the third revised edition of the Globally Harmonized System of classification and labelling of
chemicals, published by the United Nations as document ST/SG/AC.10/30/Rev.3;

IAEA means the International Atomic Energy Agency (IAEA, P.O. Box 100 – A -1400 Vienna, Austria);

ICAO means the International Civil Aviation Organization (ICAO, 999 University Street, Montreal, Quebec
H3C 5H7, Canada);

IMO means the International Maritime Organization (IMO, 4 Albert Embankment, London SE1 7SR, United
Kingdom);

Inspection body means an independent inspection and testing body approved by the competent authority;

Intermediate Bulk Container (IBC)

IBC means any rigid or flexible portable packaging, other than those specified in
Chapter 6.1, that:
(a) has a capacity of:

(i) not more than 3.0 m3 (3 000 litres) for solids and liquids of packing groups II
and III;

(ii) not more than 1.5 m3 for solids of packing group I when packed in flexible, rigid
plastics, composite, fibreboard and wooden IBCs;

(iii) not more than 3.0 m3 for solids of packing group I when packed in metal IBCs;

(iv) not more than 3.0 m3 for radioactive material of Class 7;

- 26 -


(b) is designed for mechanical handling;

(c) is resistant to the stresses produced in handling and transport, as determined by tests;

Remanufactured IBC means a metal, rigid plastics or composite IBC that:

(a) is produced as a UN type from a non-UN type; or

(b) is converted from one UN design type to another UN design type.

Remanufactured IBCs are subject to the same requirements of these Regulations that apply
to new IBCs of the same type (see also design type definition in 6.5.6.1.1);

Repaired IBC means a metal, rigid plastics or composite IBC that, as a result of impact or for any other cause
(e.g. corrosion, embrittlement or other evidence of reduced strength as compared to the design type) is
restored so as to conform to the design type and to be able to withstand the design type tests. For the
purposes of these Regulations, the replacement of the rigid inner receptacle of a composite IBC with a
receptacle conforming to the original design type from the same manufacturer is considered repair. However,
routine maintenance of rigid IBCs (see definition below) is not considered repair. The bodies of rigid plastics
IBCs and the inner receptacles of composite IBCs are not repairable. Flexible IBCs are not reparable unless
approved by the competent authority;

Routine maintenance of flexible IBCs means the routine performance on plastics or textile flexible IBCs of
operations, such as:

(a) Cleaning; or

(b) Replacement of non-integral components, such as non-integral liners and closure ties,
with components conforming to the original manufacturer's specification;

provided that these operations do not adversely affect the containment function of the flexible IBC or alter
the design type;

NOTE: For rigid IBCs, see “Routine maintenance of rigid IBCs”.

Routine maintenance of rigid IBCs means the routine performance on metal, rigid plastics or composite IBCs
of operations such as:

(a) Cleaning;

(b) Removal and reinstallation or replacement of body closures (including associated
gaskets), or of service equipment, conforming to the original manufacturer's
specifications, provided that the leaktightness of the IBC is verified; or

(c) Restoration of structural equipment not directly performing a dangerous goods
containment or discharge pressure retention function so as to conform to the design
type (e.g. the straightening of legs or lifting attachments) provided that the
containment function of the IBC is not affected;

NOTE: For flexible IBCs, see “Routine maintenance of flexible IBCs”.

Inner packaging means a packaging for which an outer packaging is required for transport;

Inner receptacle means a receptacle which require an outer packaging in order to perform its containment
function;

- 27 -


Intermediate packaging means a packaging placed between inner packagings, or articles, and an outer
packaging;

ISO (standard) means an international standard published by the International Organization for
Standardization (ISO - 1, ch. de la Voie-Creuse, CH-1211 Geneva 20, Switzerland);

Jerrican means a metal or plastics packaging of rectangular or polygonal cross-section;

Large packaging means a packaging consisting of an outer packaging which contains articles or inner
packagings and which

(a) is designed for mechanical handling; and

(b) exceeds 400 kg net mass or 450 litres capacity but has a volume of not more
than 3 m3;

Liner means a separate tube or bag inserted into a packaging, (including IBCs and large packagings) but not
forming an integral part of it, including the closures of its openings;

Liquid means a dangerous good which at 50 °C have a vapour pressure of not more than 300 kPa (3 bar),
which is not completely gaseous at 20 °C and at a pressure of 101.3 kPa, and which has a melting point or
initial melting point of 20 °C or less at a pressure of 101.3 kPa. A viscous substance for which a specific
melting point cannot be determined shall be subjected to the ASTM D 4359-90 test; or to the test for
determining fluidity (penetrometer test) prescribed in section 2.3.4 of Annex A of the European Agreement
concerning the International Carriage of Dangerous Goods by Road (ADR)1;

Manual of Tests and Criteria means the fifth revised edition of the United Nations publication entitled
“Recommendations on the Transport of Dangerous Goods, Manual of Tests and Criteria”
(ST/SG/AC.10/11/Rev.5);

Maximum capacity as used in 6.1.4 means the maximum inner volume of receptacles or packagings
expressed in litres;

Maximum net mass means the maximum net mass of contents in a single packaging or maximum combined
mass of inner packagings and the contents thereof and is expressed in kg;

Maximum normal operating pressure, for the transport of Class 7 material, means the maximum pressure
above atmospheric pressure at mean sea-level that would develop in the containment system in a period of
one year under the conditions of temperature and solar radiation corresponding to environmental conditions
in the absence of venting, external cooling by an ancillary system, or operational controls during transport;

Metal hydride storage system means a single complete hydrogen storage system, including a receptacle,
metal hydride, pressure relief device, shut-off valve, service equipment and internal components used for the
transport of hydrogen only;

Multiple-element gas container (MEGC) means a multimodal assembly of cylinders, tubes and bundles of
cylinders which are interconnected by a manifold and which are assembled within a framework. The MEGC
includes service equipment and structural equipment necessary for the transport of gases;

Offshore bulk container means a bulk container specially designed for repeated use for transport of
dangerous goods to, from and between offshore facilities. An offshore bulk container is designed and
constructed in accordance with the Guidelines for the approval of offshore containers handled in open seas
specified by the International Maritime Organization (IMO) in document MSC/Circ.860;

1
United Nations publication: ECE/TRANS/202 (Sales No. E.08.VIII.1).
- 28 -


Open cryogenic receptacle means a transportable thermally insulated receptacle for refrigerated liquefied
gases maintained at atmospheric pressure by continuous venting of the refrigerated liquefied gas;

Outer packaging means the outer protection of a composite or combination packaging together with any
absorbent materials, cushioning and any other components necessary to contain and protect inner receptacles
or inner packagings;

Overpack means an enclosure used by a single consignor to contain one or more packages and to form one
unit for convenience of handling and stowage during transport. Examples of overpacks are a number of
packages either:

(a) Placed or stacked on to a load board such as a pallet and secured by strapping, shrink
wrapping, stretch wrapping, or other suitable means; or

(b) Placed in a protective outer packaging such as a box or crate;

Package means the complete product of the packing operation, consisting of the packaging and its contents
prepared for transport;

Packaging means one or more receptacles and any other components or materials necessary for the
receptacles to perform their containment and other safety functions;

Portable tank means:

(a) For the purposes of the transport of substances of Class 1 and Classes 3 to 9, a
multimodal portable tank. It includes a shell fitted with service equipment and
structural equipment necessary for the transport of dangerous substances;

(b) For the purposes of transport of non-refrigerated, liquefied gases of Class 2, a
multimodal tank having a capacity of more than 450 litres. It includes a shell fitted
with service equipment and structural equipment necessary for the transport of gases;

(c) For the purposes of transport of refrigerated liquefied gases, a thermally insulated tank
having a capacity of more than 450 litres fitted with service equipment and structural
equipment necessary for the transport of refrigerated liquefied gases;

The portable tank shall be capable of being loaded and discharged without the need of
removal of its structural equipment. It shall possess stabilizing members external to the shell, and shall be
capable of being lifted when full. It shall be designed primarily to be loaded on to a vehicle or vessel and is
equipped with skids, mountings or accessories to facilitate mechanical handling. Road tank-vehicles, rail
tank-wagons, non-metallic tanks, gas cylinders, large receptacles, and intermediate bulk containers (IBCs)
are not considered to fall within this definition;

Pressure drum means a welded transportable pressure receptacle of a water capacity exceeding 150 litres and
of not more than 1 000 litres, (e.g. cylindrical receptacles equipped with rolling hoops, spheres on skids);

Pressure receptacle is a collective term that includes cylinders, tubes, pressure drums, closed cryogenic
receptacles, metal hydride storage system and bundles of cylinders;

Quality assurance means a systematic programme of controls and inspections applied by any organization or
body which is aimed at providing adequate confidence that the standard of safety prescribed in these
Regulations is achieved in practice;

Radiation level, for the transport of Class 7 material, means the corresponding dose rate expressed in
millisieverts per hour;

- 29 -


Radioactive contents, for the transport of Class 7 material, mean the radioactive material together with any
contaminated or activated solids, liquids, and gases within the packaging;

Receptacle means a containment vessel for receiving and holding substances or articles, including any means
of closing;

Reconditioned packagings include:

(a) Metal drums that:
(i) are cleaned to original materials of construction, with all former contents,
internal and external corrosion, and external coatings and labels removed;
(ii) are restored to original shape and contour, with chimes (if any) straightened and
sealed, and all non-integral gaskets replaced; and
(iii) are inspected after cleaning but before painting, with rejection of packagings
with visible pitting, significant reduction in material thickness, metal fatigue,
damage threads or closures, or other significant defects; or
(b) Plastics drums and jerricans that:
(i) are cleaned to original materials of construction, with all former contents,
external coatings and labels removed;
(ii) have all non-integral gaskets replaced; and
(iii) are inspected after cleaning with rejection of packagings with visible damage
such as tears, creases or cracks, or damaged threads, or closures, or other
significant defects;

Recycled plastics material means material recovered from used industrial packagings that has been cleaned
and prepared for processing into new packagings. The specific properties of the recycled material used for
production of new packagings shall be assured and documented regularly as part of a quality assurance
programme recognized by the competent authority. The quality assurance programme shall include a record
of proper pre-sorting and verification that each batch of recycled plastics material has the proper melt flow
rate, density, and tensile yield strength, consistent with that of the design type manufactured from such
recycled material. This necessarily includes knowledge about the packaging material from which the
recycled plastics have been derived, as well as awareness of the prior contents of those packagings if those
prior contents might reduce the capability of new packagings produced using that material. In addition, the
packaging manufacturer's quality assurance programme under 6.1.1.4 shall include performance of the
mechanical design type test in 6.1.5 on packagings manufactured from each batch of recycled plastics
material. In this testing, stacking performance may be verified by appropriate dynamic compression testing
rather than static load testing;

NOTE: ISO 16103:2005 “Packaging – Transport packages for dangerous goods – Recycled plastics
material”, provides additional guidance on procedures to be followed in approving the use of recycled
plastics material.

Remanufactured IBC (see “Intermediate Bulk Container (IBC)”).

Remanufactured large packaging means a metal or rigid plastics large packaging that:

(a) Is produced as a UN type from a non-UN type; or

(b) Is converted from one UN design type to another UN design type.

Remanufactured large packagings are subject to the same requirements of these Regulations
that apply to new large packagings of the same type (see also design type definition in 6.6.5.1.2);

- 30 -


Remanufactured packagings include:

(a) Metal drums that:

(i) are produced as a UN type from a non-UN type;

(ii) are converted from one UN type to another UN type; or

(iii) undergo the replacement of integral structural components (such as non-
removable heads); or

(b) Plastics drums that:

(i) are converted from one UN type to another UN type (e.g. 1H1 to 1H2); or

(ii) undergo the replacement of integral structural components;

Remanufactured drum is subject to the same requirements of these Regulations that apply to a new drum of
the same type;

Repaired IBC (see “Intermediate Bulk Container (IBC)”);

Reused large packaging means a large packaging to be refilled which has been examined and found free of
defects affecting the ability to withstand the performance tests: the term includes those which are refilled
with the same or similar compatible contents and are transported within distribution chains controlled by the
consignor of the product;

Reused packaging means a packaging to be refilled which has been examined and found free of defects
affecting the ability to withstand the performance tests: the term includes those which are refilled with the
same or similar compatible contents and are transported within distribution chains controlled by the
consignor of the product;

Routine maintenance of flexible IBC (see “Intermediate Bulk Container (IBC)”);

Routine maintenance of rigid IBC (see “Intermediate Bulk Container (IBC)”);

Salvage packaging means a special packaging into which damaged, defective, leaking or non-conforming
dangerous goods packages, or dangerous goods that have spilled or leaked, are placed for purposes of
transport for recovery or disposal;

Settled pressure means the pressure of the contents of a pressure receptacle in thermal and diffusive
equilibrium;

Shipment means the specific movement of a consignment from origin to destination;

Siftproof packaging means a packaging impermeable to dry contents including fine solid material produced
during transport;

Solid means a dangerous good, other than a gas, that do not meet the definition of liquid in this paragraph;

Tank means a portable tank (see 6.7.2.1), including a tank container, a road tank-vehicle, a rail tank-wagon
or a receptacle to contain solids, liquids, or gases, having a capacity of not less than 450 litres when used for
the transport of gases as defined in 2.2.1.1;

Test pressure means the required pressure applied during a pressure test for qualification or requalification;

- 31 -


Through or into means through or into the countries in which a consignment is transported but specifically
excludes countries “over” which a consignment is carried by air, provided that there are no scheduled stops
in those countries;

Transport index (TI) assigned to a package, overpack or freight container, or to unpackaged LSA-I or SCO-I,
for the transport of Class 7 material, means a number which is used to provide control over radiation
exposure;

Tube means a seamless transportable pressure receptacle of a water capacity exceeding 150 litres but not
more than 3 000 litres;

UNECE means the United Nations Economic Commission for Europe (UNECE, Palais des Nations, 8-14
avenue de la Paix, CH-1211 Geneva 10, Switzerland);

Vehicle means a road vehicle (including an articulated vehicle, i.e. a tractor and semi-trailer combination),
railroad car or railway wagon. Each trailer shall be considered as a separate vehicle;

Vessel means any seagoing vessel or inland waterway craft used for carrying cargo;

Wooden barrel means a packaging made of natural wood, of round cross-section, having convex walls,
consisting of staves and heads and fitted with hoops;

Working pressure means the settled pressure of a compressed gas at a reference temperature of 15 °C in a
full pressure receptacle;

- 32 -


Clarifying examples for certain defined terms

The following explanations and examples are meant to assist in clarifying the use of the
some of the packaging terms defined in this section.

The definitions in this section are consistent with the use of the defined terms throughout the
Regulations. However, some of the defined terms are commonly used in other ways. This is particularly
evident in respect of the term “inner receptacle” which has often been used to describe the “inners” of a
combination packaging.

The “inners” of “combination packagings” are always termed “inner packagings” not “inner
receptacles”. A glass bottle is an example of such an “inner packaging”.

The “inners” of “composite packagings” are normally termed “inner receptacles”. For
example, the “inner” of a 6HA1 composite packaging (plastics material) is such an “inner receptacle” since it
is normally not designed to perform a containment function without its “outer packaging” and is not
therefore an “inner packaging”.

1.2.2 Units of measurement

1.2.2.1 The following units of measurement a are applicable in these Regulations:

Measurement of SI Unit b Acceptable alternative Relationship between units
unit
Length m (metre) -- --
Area m2 (square metre) -- --
Volume m3 (cubic metre) 1 c
(litre) 1l = 10-3 m3
Time s (second) min (minute) 1 min = 60 s
h (hour) 1h = 3 600 s
d (day) 1d = 86 400 s
Mass kg (kilogramme) g (gramme) 1g = 10-3 kg
t (ton) 1t = 103 kg
Mass density kg/m3 kg/l 1 kg/l = 103 kg/m3
Temperature K (kelvin) °C (degree Celsius) 0 °C = 273,15 K
Difference of K (kelvin) °C (degree Celsius) 1 °C = 1K
temperature
Force N (newton) -- 1N = 1 kg ⋅ m/s2
Pressure Pa (pascal) bar (bar) 1 bar = 105 Pa
1 Pa = 1 N/m2
Stress N/m2 N/mm2 1 N/mm2 = 1 MPa
Work KWh (kilowatt hour) 1 kWh = 3,6 MJ
Energy
J (joule)
1J = 1N⋅m =1W⋅s
Quantity of heat eV (electronvolt) 1 eV = 0,1602 ⋅ 10-18J
Power W (watt) -- 1W = 1 J/s = 1 N ⋅ m/s
Kinematic viscosity m2/s mm2/s 1 mm2/s = -6 2
10 m /s
Dinamic viscosity Pa ⋅ s mPa ⋅ s 1 mPa ⋅ s = 10-3Pa ⋅ s
Activity Bq (becquerel)
Dose equivalent Sv (sievert)

- 33 -


Notes to 1.2.2.1:
a
The following round figures are applicable for the conversion of the units hitherto used into
SI Units.

Force Stress
1 kg = 9.807 N 1 kg/mm2 = 9.807 N/mm2
1 N = 0.102 kg 1 N/mm2 = 0.102 kg/mm2

Pressure
1 Pa = 1 N/m2 = 10-5 bar = 1.02 × 10-5 kg/cm2 = 0.75 × 10-2 torr
1 bar = 105 Pa = 1.02 kg/cm2 = 750 torr
1 kg/cm2 = 9.807 × 104 Pa = 0.9807 bar = 736 torr
1 torr = 1.33 × 102 Pa = 1.33 × 10-3 bar = 1.36 × 10-3kg/cm2

Energy, Work, Quantity of heat
1 J=1 Nm = 0.278 × 10-6 kWh = 0.102 kgm = 0.239 × 10-3 kcal
1 kWh = 3.6 × 106 J = 367 × 103 kgm = 860 kcal
1 kgm = 9.807 J = 2.72 × 10-6 kWh = 2.34 × 10-3 kcal
1 kcal = 4.19×103J = 1.16 × 10-3 kWh = 427 kgm

Power Kinematic viscosity
1W = 0.102 kgm/s = 0.86 kcal/h 1 m2/s = 104 St (Stokes)
1 kgm/s = 9.807 W = 8.43 kcal/h 1 St = 10-4 m2/s
1 kcal/h = 1.16 W = 0.119 kgm/s

Dynamic viscosity
1 Pa ⋅ s = 1 Ns/m2 = 10 P (poise) = 0.102 kgs/m2
1P = 0.1 Pa ⋅ s = 0.1 Ns/m2 = 1.02 × 10-2 kgs/m2
1 kgs/m2 = 9.807 Pa ⋅ s = 9.807 Ns/m2 = 98.07 P

b
The International System of Units (SI) is the result of decisions taken at the General Conference
on Weights and Measures (Address: Pavillon de Breteuil, Parc de St-Cloud, F-92 310 Sèvres).
c
The abbreviation “L” for litre may also be used in place of the abbreviation “l” when a
typewriter cannot distinguish between figure “1” and letter “l”.

- 34 -


The decimal multiples and sub-multiples of a unit may be formed by prefixes or symbols,
having the following meanings, placed before the name or symbol of the unit:

Factor Prefix Symbol
18
1 000 000 000 000 000 000 = 10 quintillion exa E
1 000 000 000 000 000 = 1015 quadrillion peta P
1 000 000 000 000 = 1012 trillion tera T
1 000 000 000 = 109 billion giga G
1 000 000 = 106 million mega M
1 000 = 103 thousand kilo k
100 = 102 hundred hecto h
10 = 101 ten deca da
0.1 = 10-1 tenth deci d
0.01 = 10-2 hundredth centi c
0.001 = 10-3 thousandth milli m
0.000 001 = 10-6 millionth micro μ
0.000 000 001 = 10-9 billionth nano n
0.000 000 000 001 = 10-12 trillionth pico p
0.000 000 000 000 001 = 10-15 quadrillionth femto f
0.000 000 000 000 000 001 = 10-18 quintillionth atto a

NOTE: 109= 1 billion is United Nations usage in English. By analogy, so is 10-9 = 1 billionth.

1.2.2.2 Deleted.

1.2.2.3 Whenever the mass of a package is mentioned, the gross mass is meant unless otherwise
stated. The mass of containers or tanks used for the transport of goods is not included in the gross mass.

1.2.2.4 Unless expressly stated otherwise, the sign “%” represents:

(a) In the case of mixtures of solids or of liquids, and also in the case of solutions and of
solids wetted by a liquid: a percentage mass based on the total mass of the mixture, the
solution or the wetted solid;

(b) In the case of mixtures of compressed gases: when filled by pressure, the proportion of
the volume indicated as a percentage of the total volume of the gaseous mixture, or,
when filled by mass, the proportion of the mass indicated as a percentage of the total
mass of the mixture.

In the case of mixtures of liquefied gases and gases dissolved under pressure: the proportion
of the mass indicated as a percentage of the total mass of the mixture.

1.2.2.5 Pressures of all kinds relating to receptacles (such as test pressure, internal pressure, safety-
valve opening pressure) are always indicated in gauge pressure (pressure in excess of atmospheric pressure);
however, the vapour pressure of substances is always expressed in absolute pressure.

- 35 -


CHAPTER 1.3

TRAINING

1.3.1 Persons engaged in the transport of dangerous goods shall be trained in the contents of
dangerous goods requirements commensurate with their responsibilities. Employees shall be trained in
accordance with 1.3.2 before assuming responsibilities and shall only perform functions, for which required
training has not yet been provided, under the direct supervision of a trained person. Training requirements
specific to security of dangerous goods in Chapter 1.4 shall also be addressed.

1.3.2 Individuals such as those who classify dangerous goods; pack dangerous goods; mark and
label dangerous goods; prepare transport documents for dangerous goods; offer or accept dangerous goods
for transport; carry or handle dangerous goods in transport; mark or placard or load or unload packages of
dangerous goods into or from transport vehicles, bulk packagings or freight containers; or are otherwise
directly involved in the transport of dangerous goods as determined by the competent authority; shall be
trained in the following:

(a) General awareness/familiarization training:

(i) Each person shall be trained in order to be familiar with the general provisions
of dangerous goods transport requirements;

(ii) Such training shall include a description of the classes of dangerous goods;
labelling, marking, placarding and packaging, segregation and compatibility
requirements; a description of the purpose and content of the dangerous goods
transport document; and a description of available emergency response
documents;

(b) Function-specific training: Each person shall be trained in specific dangerous goods
transport requirements which are applicable to the function that person performs;

(c) Safety training: Commensurate with the risk of exposure in the event of a release and
the functions performed, each person shall be trained in:

(i) Methods and procedures for accident avoidance, such as proper use of package-
handling equipment and appropriate methods of stowage of dangerous goods;

(ii) Available emergency response information and how to use it;

(iii) General dangers presented by the various classes of dangerous goods and how
to prevent exposure to those hazards, including if appropriate the use of
personal protective clothing and equipment; and

(iv) Immediate procedures to be followed in the event of an unintentional release of
dangerous goods, including any emergency response procedures for which the
person is responsible and personal protection procedures to be followed.

1.3.3 Records of training received according to this Chapter shall be kept by the employer and
made available to the employee or competent authority, upon request. Records shall be kept by the employer
for a period of time established by the competent authority.

1.3.4 The training required by 1.3.2 shall be provided or verified upon employment in a position
involving dangerous goods transport and shall be periodically supplemented with retraining as deemed
appropriate by the competent authority.

- 37 -


CHAPTER 1.4

SECURITY PROVISIONS

Introductory notes

NOTE 1: This Chapter provides requirements intended to address the security of dangerous goods in
transport in all modes. Mode specific security provisions can be found in Chapter 7.2. National and modal
authorities may apply additional security provisions which should be considered when offering or
transporting dangerous goods.

NOTE 2: For the purposes of this Chapter security means measures or precautions to be taken to
minimise theft or misuse of dangerous goods that may endanger persons or property.

1.4.1 General provisions

1.4.1.1 All persons engaged in the transport of dangerous goods shall consider security requirements
for the transport of dangerous goods commensurate with their responsibilities.

1.4.1.2 Consignors shall only offer dangerous goods to carriers that have been appropriately
identified.

1.4.1.3 Transit sites, such as airside warehouses, marshalling yards and other temporary storage
areas shall be properly secured, well lit and, where possible, not be accessible to the general public.

1.4.2 Security training

1.4.2.1 The training specified for individuals in 1.3.2 (a), (b) or (c) shall also include elements of
security awareness.

1.4.2.2 Security awareness training shall address the nature of security risks, recognising security
risks, methods to address and reduce such risks and actions to be taken in the event of a security breach. It
shall include awareness of security plans (if appropriate) commensurate with the responsibilities of
individuals and their part in implementing security plans.

1.4.2.3 Such training shall be provided or verified upon employment in a position involving
dangerous goods transport and shall be periodically supplemented with retraining.

1.4.2.4 Records of all security training received shall be kept by the employer and made available to
the employee or competent authority, upon request. Records shall be kept by the employer for a period of
time established by the competent authority.

1.4.3 Provisions for high consequence dangerous goods

1.4.3.1 In implementing national security provisions competent authorities shall consider
establishing a programme for identifying consignors or carriers engaged in the transport of high consequence
dangerous goods for the purpose of communicating security related information. An indicative list of high
consequence dangerous goods is provided in Table 1.4.1.

1.4.3.2 Security plans

1.4.3.2.1 Carriers, consignors and others (including infrastructure managers) engaged in the transport
of high consequence dangerous goods (see Table 1.4.1) shall adopt, implement and comply with a security
plan that addresses at least the elements specified in 1.4.3.2.2.

- 39 -


1.4.3.2.2 The security plan shall comprise at least the following elements:

(a) Specific allocation of responsibilities for security to competent and qualified persons
with appropriate authority to carry out their responsibilities;
(b) Records of dangerous goods or types of dangerous goods transported;
(c) Review of current operations and assessment of vulnerabilities, including inter-modal
transfer, temporary transit storage, handling and distribution as appropriate;
(d) Clear statements of measures, including training, policies (including response to
higher threat conditions, new employee/employment verification etc.), operating
practices (e.g. choice/use of routes where known, access to dangerous goods in
temporary storage, proximity to vulnerable infrastructure etc.), equipment and
resources that are to be used to reduce security risks;
(e) Effective and up to date procedures for reporting and dealing with security threats,
breaches of security or security incidents;
(f) Procedures for the evaluation and testing of security plans and procedures for periodic
review and update of the plans;
(g) Measures to ensure the security of transport information contained in the plan; and
(h) Measures to ensure that the distribution of the transport information is limited as far as
possible. (Such measures shall not preclude provision of transport documentation
required by Chapter 5.4 of these Regulations).

NOTE: Carriers, consignors and consignees should co-operate with each other and with
appropriate authorities to exchange threat information, apply appropriate security measures and respond to
security incidents.

- 40 -


Table 1.4.1: Indicative list of high consequence dangerous goods

High consequence dangerous goods are those which have the potential for misuse in a
terrorist incident and which may, as a result, produce serious consequences such as mass casualties or mass
destruction. The following is an indicative list of high consequence dangerous goods:

Class 1, Division 1.1 explosives
Class 1, Division 1.3 compatibility group C explosives
Class 1, Division 1.4 UN Nos. 0104, 0237, 0255, 0267, 0289, 0361, 0365, 0366, 0440, 0441, 0455,
0456 and 0500
Division 2.1 flammable gases in bulk
Division 2.3 toxic gases (excluding aerosols)
Class 3 flammable liquids of packing groups I and II in bulk
Class 3 and Division 4.1 desensitized explosives
Division 4.2 goods of packing group I in bulk
Division 4.3 goods of packing group I in bulk
Division 5.1 oxidizing liquids of packing group I in bulk
Division 5.1 perchlorates, ammonium nitrate, ammonium nitrate fertilisers and ammonium
nitrate emulsions or suspensions or gels, in bulk
Division 6.1 toxic substances of packing group I
Division 6.2 infectious substances of Category A (UN Nos. 2814 and 2900)
Class 7 radioactive material in quantities greater than 3 000 A1 (special form) or
3 000 A2, as applicable, in Type B(U) or Type B(M) or Type C packages
Class 8 corrosive substances of packing group I in bulk

NOTE: For the purposes of this table, “in bulk” means transported in quantities greater than
3 000 kg or 3 000 l in portable tanks or bulk containers.

1.4.3.2.3 For radioactive material, the provisions of this Chapter and of section 7.2.4 are deemed to be
complied with when the provisions of the Convention on Physical Protection of Nuclear Material1 and the
IAEA circular on “The Physical Protection of Nuclear Material and Nuclear Facilities”2 are applied.

1
IAEACIRC/274/Rev.1, IAEA, Vienna (1980).
2
IAEACIRC/225/Rev.4 (Corrected), IAEA, Vienna (1999). See also “Guidance and Considerations for
the Implementation of INFCIRC/225/Rev.4, the Physical Protection of Nuclear Material and Nuclear
Facilities, IAEA-TECDoc-967/Rev.1”.
- 41 -


CHAPTER 1.5

GENERAL PROVISIONS CONCERNING CLASS 7

1.5.1 Scope and application

1.5.1.1 These Regulations establish standards of safety which provide an acceptable level of control
of the radiation, criticality and thermal hazards to persons, property and the environment that are associated
with the transport of radioactive material. These regulations are based on the IAEA Regulations for the Safe
Transport of Radioactive Material (2009 Edition), Safety Standards Series No. TS-R-1, IAEA,
Vienna (2009). Explanatory material can be found in “Advisory Material for the IAEA Regulations for the
Safe Transport of Radioactive Material (2005 Edition)”, Safety Standard Series No. TS-G-1.1 (Rev.1),
IAEA, Vienna (2008). The prime responsibility for safety shall rest with the person or organization
responsible for facilities and activities that give rise to radiation risk.

1.5.1.2 The objective of these Regulations is to establish requirements that must be satisfied to
ensure safety and to protect persons, property and the environment from the effects of radiation in the
transport of radioactive material. This protection is achieved by requiring:

(a) Containment of the radioactive contents;

(b) Control of external radiation levels;

(c) Prevention of criticality; and

(d) Prevention of damage caused by heat.

These requirements are satisfied firstly by applying a graded approach to contents limits for
packages and conveyances and to performance standards applied to package designs depending upon the
hazard of the radioactive contents. Secondly, they are satisfied by imposing requirements on the design and
operation of packages and on the maintenance of packagings, including a consideration of the nature of the
radioactive contents. Finally, they are satisfied by requiring administrative controls including, where
appropriate, approval by competent authorities.

1.5.1.3 These Regulations apply to the transport of radioactive material by all modes on land, water
or in the air, including transport which is incidental to the use of the radioactive material. Transport
comprises all operations and conditions associated with and involved in the movement of radioactive
material; these include the design, manufacture, maintenance and repair of packaging, and the preparation,
consigning, loading, transport including in-transit storage, unloading and receipt at the final destination of
loads of radioactive material and packages. A graded approach is applied to the performance standards in
these Regulations that are characterized by three general severity levels:

(a) Routine conditions of transport (incident free);

(b) Normal conditions of transport (minor mishaps);

(c) Accident conditions of transport.

1.5.1.4 These Regulations do not apply to:

(a) Radioactive material that is an integral part of the means of transport;

(b) Radioactive material moved within an establishment which is subject to appropriate
safety regulations in force in the establishment and where the movement does not
involve public roads or railways;
- 43 -


(c) Radioactive material implanted or incorporated into a person or live animal for
diagnosis or treatment;

(d) Radioactive material in consumer products which have received regulatory approval,
following their sale to the end user;

(e) Natural material and ores containing naturally occurring radionuclides which are
either in their natural state, or have only been processed for purposes other than for
extraction of the radionuclides, and which are not intended to be processed for use of
these radionuclides provided the activity concentration of the material does not exceed
10 times the values specified in 2.7.2.2.1 (b), or calculated in accordance with
2.7.2.2.2 to 2.7.2.2.6;

(f) Non-radioactive solid objects with radioactive substances present on any surfaces in
quantities not in excess of the limit set out in the definition for “contamination” in
2.7.1.2.

1.5.1.5 Specific provisions for the transport of excepted packages

1.5.1.5.1 Excepted packages which may contain radioactive material in limited quantities,
instruments, manufactured articles and empty packagings as specified in 2.7.2.4.1 shall be subject only to the
following provisions of Parts 5 to 7:

(a) The applicable provisions specified in 5.1.2, 5.1.3.2, 5.1.4, 5.1.5.4, 5.2.1.7 and
7.1.8.5.2;

(b) The requirements for excepted packages specified in 6.4.4; and

(c) If the excepted package contains fissile material, one of the fissile exceptions provided
by 2.7.2.3.5 shall apply and the requirement of 6.4.7.2 shall be met.

1.5.1.5.2 Excepted packages shall be subject to the relevant provisions of all other parts of these
Regulations.

1.5.2 Radiation protection programme

1.5.2.1 The transport of radioactive material shall be subject to a radiation protection programme
which shall consist of systematic arrangements aimed at providing adequate consideration of radiation
protection measures.

1.5.2.2 Doses to persons shall be below the relevant dose limits. Protection and safety shall be
optimized in order that the magnitude of individual doses, the number of persons exposed, and the likelihood
of incurring exposure shall be kept as low as reasonably achievable, economic and social factors being taken
into account, within the restriction that the doses to individuals be subject to dose constraints. A structured
and systematic approach shall be adopted and shall include consideration of the interfaces between transport
and other activities.

1.5.2.3 The nature and extent of the measures to be employed in the programme shall be related to
the magnitude and likelihood of radiation exposures. The programme shall incorporate the requirements in
1.5.2.2, 1.5.2.4 to 1.5.2.7 and 7.1.8.1.1. Programme documents shall be available, on request, for inspection
by the relevant competent authority.

- 44 -


1.5.2.4 For occupational exposures arising from transport activities, where it is assessed that the
effective dose:

(a) Is likely to be between 1 and 6 mSv in a year, a dose assessment programme via
workplace monitoring or individual monitoring shall be conducted;

(b) Is likely to exceed 6 mSv in a year, individual monitoring shall be conducted.

When individual monitoring or workplace monitoring is conducted, appropriate records shall
be kept.

NOTE: For occupational exposures arising from transport activities, where it is assessed that the
effective dose is most unlikely to exceed 1mSv in a year, no special work patterns, detailed monitoring, dose
assessment programmes or individual record keeping need be required.

1.5.2.5 In the event of accidents or incidents during the transport of radioactive material, emergency
provisions, as established by relevant national and/or international organizations, shall be observed to protect
persons, property and the environment. Appropriate guidelines for such provisions are contained in
“Planning and Preparing for Emergency Response to Transport Accidents Involving Radioactive Material”,
Safety Standard Series No. TS-G-1.2 (ST-3), IAEA, Vienna (2002).

1.5.2.6 Emergency procedures shall take into account the formation of other dangerous substances
that may result from the reaction between the contents of a consignment and the environment in the event of
an accident.

1.5.2.7 Workers shall be appropriately trained in the radiation hazards involved and the precautions
to be observed in order to ensure restriction of their exposure and that of other persons who might be affected
by their actions.

1.5.3 Quality assurance

1.5.3.1 Quality assurance programmes based on international, national or other standards acceptable
to the competent authority shall be established and implemented for the design, manufacture, testing,
documentation, use, maintenance and inspection of all special form radioactive material, low dispersible
radioactive material and packages and for transport and in-transit storage operations to ensure compliance
with the relevant provisions of these Regulations. Certification that the design specification has been fully
implemented shall be available to the competent authority. The manufacturer, consignor or user shall be
prepared to provide facilities for competent authority inspection during manufacture and use and to
demonstrate to any cognizant competent authority that:

(a) The manufacturing methods and materials used are in accordance with the approved
design specifications; and

(b) All packagings are periodically inspected and, as necessary, repaired and maintained
in good condition so that they continue to comply with all relevant requirements and
specifications, even after repeated use.

Where competent authority approval is required, such approval shall take into account and
be contingent upon the adequacy of the quality assurance programme.

1.5.4 Special arrangement

1.5.4.1 Special arrangement shall mean those provisions, approved by the competent authority,
under which consignments which do not satisfy all the requirements of these Regulations applicable to
radioactive material may be transported.

- 45 -


1.5.4.2 Consignments for which conformity with any provision applicable to Class 7 is
impracticable shall not be transported except under special arrangement. Provided the competent authority is
satisfied that conformity with the Class 7 provisions of these Regulations is impracticable and that the
requisite standards of safety established by these Regulations have been demonstrated through alternative
means the competent authority may approve special arrangement transport operations for single or a planned
series of multiple consignments. The overall level of safety in transport shall be at least equivalent to that
which would be provided if all the applicable requirements had been met. For international consignments of
this type, multilateral approval shall be required.

1.5.5 Radioactive material possessing other dangerous properties

1.5.5.1 In addition to the radioactive and fissile properties, any subsidiary risk of the contents of a
package, such as explosiveness, flammability, pyrophoricity, chemical toxicity and corrosiveness, shall also
be taken into account in the documentation, packing, labelling, marking, placarding, stowage, segregation
and transport, in order to be in compliance with all relevant provisions for dangerous goods of these
regulations.

1.5.6 Non-compliance

1.5.6.1 In the event of a non-compliance with any limit in these Regulations applicable to radiation
level or contamination:

(a) The consignor shall be informed of the non-compliance

(i) by the carrier if the non-compliance is identified during transport; or

(ii) by the consignee if the non-compliance is identified at receipt;

(b) The carrier, consignor or consignee, as appropriate, shall:

(i) take immediate steps to mitigate the consequences of the non-compliance;

(ii) investigate the non-compliance and its causes, circumstances and consequences;

(iii) take appropriate action to remedy the causes and circumstances that led to the
non-compliance and to prevent a recurrence of similar circumstances that led to
the non-compliance; and

(iv) communicate to the relevant competent authority(ies) on the causes of the non-
compliance and on corrective or preventive actions taken or to be taken; and

(c) The communication of the non-compliance to the consignor and relevant competent
authority(ies), respectively, shall be made as soon as practicable and it shall be
immediate whenever an emergency exposure situation has developed or is developing.

- 46 -

01 e part1

More Related Content

Viewers also liked (20)

Similar to 01 e part1 (20)

More from Califa31 (20)

Recently uploaded (20)

01 e part1