A Hybrid DC-DC Converter for Standalone Applications

International Research Journal of Engineering and Technology (IRJET) e-ISSN: 2395 -0056
Volume: 04 Issue: 03 | Mar -2017 www.irjet.net p-ISSN: 2395-0072
© 2017, IRJET | Impact Factor value: 5.181 | ISO 9001:2008 Certified Journal | Page 2666
A Hybrid DC-DC Converter for Standalone Applications
Varun Jo Abu1, Sija Gopinathan2, Leela Salim3
1PG Scholar, Department of Electrical and Electronics Engineering, Mar Athanasius College of Engineering,
Kothamangalam, Kerala, India
2Assistant Professor, Department of Electrical and Electronics Engineering, Mar Athanasius College of Engineering,
3Assistant Professor, Department of Electrical and Electronics Engineering, Mar Athanasius College of Engineering,
---------------------------------------------------------------------***---------------------------------------------------------------------
Abstract - The conventional energy sourcesavailablein the
world are diminishing every year creating a huge difference
between the demanded energy and the available energy.
Efficient utilization of the ample renewable energy resources
present in the world can be used to cover this extra demand.
With the use of this renewable energy sources the levels of
pollution and global warming can controlled to a lower level.
A significant demerit with the renewable energy sources is
their fluctuating nature. Hybridization technique is hence
utilized to overcome this problem. This allows two sources to
meet the load separately or simultaneously depending on the
availability. In this paper a double input single output DC-DC
converter is presented for stand-alone systems. The topology
operates as a bootstrap circuit by employing the charging
switches in case of only one input port powering or one input
being short circuited and maintains the expected output
voltage making the system fault tolerant.
Key Words: Hybrid system, Multi-input converter,
Bootstrap operation, Solar panel, Fuel cell
1. INTRODUCTION
Rise in the energy demand and limitation in fossil fuels have
increased the role ofrenewableenergyresources.Renewable
energy sources will have to play a significant role in
overcoming these problems. Systems based on petroleum
product and fossil fuels will resultinenvironmentalpollution
and hence global warming. This elevated the need for
renewable energy sources which is abundant and
environment friendly. Solar energy, wind energy, etc. are
capable of supplying energy tomeetthepowerdemand.Even
though the capital cost and space requirement for such
systemsare high, the runningcost is extremelylow.Theycan
be easily utilized in distributed generation,microgrid,stand-
alone systems, rural telephony systems etc. The main
disadvantage of such a system is its unpredictable and
intermittent nature, i.e., the output from these systems will
always be fluctuating and doesn’t deliver a constant output.
To overcome this challenge, hybrid renewable energy
systems were implemented which clubs two or more energy
resources to produce a constant output. Hybridization
improves the efficiency and life of the system and also brings
down the storage requirement.However,bycombiningthese
two fluctuating sources, the efficiency and reliability of the
system can be refined notably. At the same time, the capital
cost and complexity can increase as a result of hybridization.
Multi input converters (MIC) have a simpler structure,
improved power density and lower cost due to sharing of
switches and other components [1]-[3]. Dynamic
performance can be improved and complex communication
among multiple different sources can be avoided due to the
unified power management with centralized control. Thus
MIC is appropriate for renewable power systems. Isolated
[4]-[6] and non-isolated MIC has been developed for DC-DC
conversion. GalvanicisolationisusedinisolatedMICs,butthe
disadvantage is the larger number of active switches present
in it. Non-isolated converters have the advantages of small
size, high power density and more efficiency. Based on buck
and/or boost converter structures, various non-isolated
topologies were developed. A triple input boost DC-DC
converter developed in [7] consists of a photovoltaic source,
fuel cell and a battery in a unified structure. A buck voltage
source cell parallel connected MIC is presented in [8] which
can operatein buck, boost or buck-boost mode,butwithonly
any one of the input ports powering. Two-input series-
connected buck DC–DCconvertersproposedin[9]–[11]have
a simple topology and efficient energy utilization. They can
deliver power to the load from two power sources
simultaneously or individually. The series-connected two-
input converter in [10] has one input port connected to a
renewable energy source and other to a storage element,
used for nanogrid application. Although both individual and
simultaneous operations are possible for this converter,
when one input source is shut down, the other port takes up
the operation and the output voltage will be less than the
existing input voltage. This implies that the converter is not
able to maintain the expected output voltage in the one port
powering case if the expected output voltage is more than
either of two input voltages.
Due to the randomness and intermittency of renewable
energy sources present as inputs, it is necessary for the
converter to be loaded with a flexiblecompensationprogram
for error free individual operation. A circuit topology was
designed in [12] which include a combination of a charging
switch and a series connected double input converter
(SCDIC). In this circuit, the converter operates in bootstrap
mode in the case of one port powering and it meets the
expected output voltage.Thedisadvantagewiththistopology

is that it employs a large number of switches and hence the
switchinglosses willbelarger.Butthistopologyhasthemerit
of employing only a single inductor for any number of input
ports when compared to parallel boost converters. This
advantage will in turn reduce the volume and cost and
improve the dynamic response of the system.
This paper proposes another series connected double input
converter with reduced number of switches and possessing
all the advantage of the circuit presented in [12]. With the
presence of a blocking diode, the chance of fault due to a
short circuited input can be ruled out. In such a case, the
short circuit input port will be separated from the converter
and the port will be powered by bootstrap operation.
The paper consists of four sections. After introduction in
section I, the circuit features, principle and modes of
operation will be described in section II. Section III presents
the simulation model and results oftheconverterandsection
IV concludes the paper.
Table -1: Comparison of the proposed converterwithSCDIC
converter [12]
PARAMETER SCDIC CONVERTER PROPOSED CONVERTER
No. of inputs 2 2
No. of switches 6 5
No. of diodes 1 2
2. HYBRID DC-DC CONVERTER
A circuit diagram of the hybrid energy system is shown in
figure 3, where one of the inputs is connectedtothePVarray
and the other input is connected to a fuel cell. Vin1 and Vin2
are the two input source voltages. C1 is the bootstrap
capacitor and is connected across Vin1. D1 is the breaking
diode and it separates a short circuited input source from
the converter. Switches S4 and S5 are the charging switches
during bootstrap operation. Lf is the filter inductor, Cf is the
filter capacitor and Ro is the load resistor. All the switches in
the converter are MOSFETs. This configuration allows both
individual and simultaneous operation of the converters. So
the circuit can operate in three modes depending on the
available inputs. The circuit has 6 states of operation. When
both sources are unavailable the entire circuit will beturned
off. Table 2 shows the modes of operation.
Table -2: Modes of operation
MODE VIN1(SOLAR SOURCE) VIN2 (FUEL CELL)
I(Simultaneous operation) ON ON
II(Bootstrap operation) OFF ON
III ON OFF
Although modes I and II can occur in a practical situation,
mode III has least chances to occur. Figure 1 shows the
circuit diagram of the converter. States 1 and 2 is during the
bootstrap operation mode, i.e., during the individual
operation of Vin2. Rest of the states from 3-6 occurs at the
remaining modes, i.e., during individual operation of Vin1 or
during simultaneous operation.Theexpectedoutputvoltage
is kept above either of the two input voltages. Take
Vin1>Vo>Vin2.
Fig -1: Circuit diagram of the hybrid DC-DC converter for
standalone applications
State I: (S2, S4, S5 ON, S1, S3 OFF)
Vin2 charges the capacitor C1 through the switches S2, S4
and S5. Now the voltage across the points A and B (vAB) will
be Vin2 and it is below Vo. Now the voltage appe aring across
the inductor Lf is negative and thereby the current iLf
decreases. The power to load is supplied alone by Vin2 in this
state. Figure 2(a) shows the equivalent circuit during state I.
(1)
(2)
Fig -2: Equivalent circuit during (a) State I, (b) State II
State II: (S1 ON, S2, S3 S4, S5 OFF)
Vin2 is now in series with the bootstrapcapacitorC1.Now
the voltage across the points A and B (vAB) will be2Vin2 andit
is above Vo. This makes the voltage across the inductor Lf
positive and thereby the inductor current iLf rises. Figure
2(b) shows the equivalent circuit during state II.
(3)

(4)
It can be seen that when Vin1 is powered off from its port, the
port is taken up by Vin2 through bootstrap operation and the
expected output voltage is met. For the remaining states,
both sources Vin1 and Vin2 are available and simultaneous
operation of the converter takes place.
State III: (S1 ON, S2, S3, S4, S5 OFF)
SourcesVin1 and Vin2 connected in seriesduringthisstate
to deliver the power to the load. The voltage across the
points A and B (vAB) will be Vin1+Vin2 and it is more than Vo.
Now the voltage appearing across the inductor Lf is
(Vin1+Vin2-Vo) and thereby the current iLf increases linearly.
Figure 3(a) shows the equivalent circuit during state III.
(5)
(6)
Fig -3: Equivalent circuit during (a) State III, (b) State IV
State IV: (S4, S5 ON, S1, S2, S3 OFF)
Input source Vin1 only deliver the power to the load. The
voltage across the points A and B will be Vin1 and it is more
than Vo. Now the voltage appearing across the inductor Lf is
(Vin1 -Vo) and thereby the current iLf increases. Figure 3(b)
shows the equivalent circuit during state IV.
(7)
(8)
State V: (S2 ON, S1, S3, S4, S5 OFF)
Input source Vin2 only supplies the power to the load.
The voltage across the points A and B will be Vin2 and it is
less than Vo. Now the voltage appearing across the inductor
Lf is (Vin2-Vo) and thereby the current iLf reduces. Figure 4(a)
shows the equivalent circuit during state V.
(9)
(10)
Fig-4: Equivalent circuit during (a) State V, (b) State VI
State VI: (S3 ON, S1, S2, S4, S5 OFF)
Inductor current iLf freewheels through the switch S3
during this state. The voltage across the points A and B will
be zero. The current iLf decreases. Figure 4(b) shows the
equivalent circuit during state VI.
(11)
(12)
Depending on the availability of the sources, their input
voltages and power, the order of states during simultaneous
operation will be states III, IV, VI or states III, V, VI. If more
power is to be taken from the input source 1, stateIVfollows
state III. In case more power is to be withdrawn from input
source 2, state V follows state VI. -Figure 5(a) & (b) shows
the waveforms related to mode I (simultaneous operation).
Figure 6 presents the corresponding waveforms of mode II
(bootstrap operation/individual operation).
Fig -5: Waveforms during Mode I (simultaneous operation)
with order of states (a) III, IV, VI, (b) III, V, VI

Fig -6: Waveforms during Mode II (Bootstrap operation)
3. SIMULATION MODELS AND RESULTS
The simulations were done on MATLAB/ Simulink R2014a.
Figure 12 shows the simulink model of the converter.
Table -3: Simulation components, parameters and values
COMPONENT AND PARAMETERS VALUE
Input Voltage 1 (Vin1) 50 V
Input Voltage 2 (Vin2) 30 V
Output Voltage (Vo) 40 V
Bootstrap Capacitor (C1) 220 μF
Filter Inductance (Lf) 400 μH
Filter Capacitance (Cf) 300 μF
Load Resistance (Ro) 2.2 kΩ
Switching Frequency (fs) 50 kHz
Figure 7 shows the output voltage and current during the
simultaneous operation, i.e., during mode I. The output
voltage settles at 40 V.
Fig -7: Output Voltage and Current when Vin1=50V and
Vin2=30V
Figure 8 shows the gate pulses to the converter switches
during mode I. The voltage stresses across each of the
switches are plotted in figure 9. Themaximumvoltagestress
across a switch is 80 V. Figure 10 shows the ripples in the
output voltage waveform. Ripple percentage is seen as
1.51% of the average value.
Fig -8: Mode I: Gate pulse voltages
Fig -9: Mode I: Voltage stress across switches
Fig -10: Mode I: Output voltage ripple
Figure 11 shows the output voltage and current during the
bootstrap operation, i.e., duringmodeII.AlthoughVin2 isonly
available, the output voltage is obtained as 40 V.
Fig -11: Mode II: Output Voltage and Current when
Vin1=0V and Vin2=30V
Figure 13 shows the gate pulses to the converter switches
during mode I. The voltage stresses across the switches are
plotted in figure 14. The maximum voltage stress across a
switch is 50 V during this mode. Figure 15 shows the ripples
in the output voltage waveform. Output voltage ripple is
obtained as 0.042%

Fig -12: Simulink model of the DC-DC converter
Fig -13: Mode II: Gate pulse voltages
Fig -14: Mode II: Voltage stress across switches
Fig -15: Mode II: Output voltage ripple
4. CONCLUSIONS
The hybrid DC-DC converter for standalone applications is a
simple and robust topology to solve the problems related to
renewable energy source and ensure a constant output voltage.
With the help of bootstrap operation, the fuel cell port can charge
the renewable energy port if the renewable energy source is
powered off from the circuit. This circuit contains only a single
inductor and there is no need for extra inductors while adding
more input ports. This reduces the size and cost of the converter.
Power density is improved and a good dynamic response is
possible with this circuit. It is highly efficient during
simultaneous and individual operation of the converter.
REFERENCES
[1] K. Jin, X. Ruan, M. Yang and M. Xu, “A hybrid fuel cell
power system,” in IEEE Transactions on Industrial
Electronics, vol. 56, no. 4, pp. 1212–1222, Apr.2009.
[2] W. Jiang and B. Fahimi, “Active current sharing and
source management in fuel-battery hybrid power
system,” in IEEE Transactions on Industrial Electronics,
vol. 57, no. 2, pp. 752–761, Feb.2010.
[3] L. Khanh, J. Seo, Y. Kim and D. Won, “Power management
strategies for a grid connected PV-FC hybrid system,” in
IEEE Transactions on Power Delivery, vol. 25, no. 3, pp.
1874–1882, Jul.2010.
[4] J. L. Duarte, M. A. M. Hendrix and M. G. Simoes, “Three-
port bidirectional converter for hybridfuel cell systems,”
in IEEE Transactions on Power Electronics, vol. 22, no. 2,
pp.480–487, Mar. 2012.
[5] C. Zhao, S.D. Round, and W. Johann, “An isolated three-
port bidirectional DC-DC converter with decoupled
power flow management”,in IEEETransactionsonPower
Electronics, vol. 23, no. 5, pp. 2443–2453, Sep.2008.
[6] M. Sarhangzadeh, S. H. Hosseini, M. B. B. Sharifian, and G.
B. Gharehpetian,“Multiinput directDC-ACconverter with
high-frequency link forclean powergenerationsystems,”
in IEEE Transactions on Power Electronics, vol. 26, no. 6,
pp. 1777–1789, Jun.2011.
[7] F. Nejabatkhah, S. Danyali, S. H. Hosseini, M. Sabahi, and
S. M. Niapour, “Modeling and control of a new three-
input dc-dc boost converter for hybrid PV/FC/battery
power system, ” in IEEE Transactions on Power
Electronics, vol. 27, no. 5, pp. 2309–2324, May 2012.
[8] A. Khaligh, J. Cao, and Y. Lee, “A multiple-input DC-DC
converter topology,” in IEEE Transactions on Power
Electronics, vol. 24, no. 3, pp. 862–868, Mar.2009.

[9] Y. Li, D. Yang, and X. Ruan, “A new double-input DC-DC
converter”, in Transactions of China Electrotechnical
Society, vol. 23, no. 6, pp. 77–82, Jun.2008.
[10] Y. Li, X. Ruan, D. Yang, and F. Liu, “Interleaved dual-edge
modulation scheme for double-input Buck converter”,in
Transactions of China ElectrotechnicalSociety,vol.24,no.
4, pp. 139–146, Apr.2009.
[11] Y. Li, X. Ruan, D. Yang, and F. Liu, “Modeling anddesignof
control system for double-input DC/DC converter”, in
Transactions of China Electrotechnical Society, vol. 25,
no. 11, pp. 90–99, Nov.2010.
[12] X. Sun, W. Wang, B. Wang and Z. Zhang, “Alternatesource
port tolerant series connected double input DC-DC
converter,” IEEE Transactions on Power Electronics, vol.
30, no. 5, pp.2733-2742, May 2015.

A Hybrid DC-DC Converter for Standalone Applications

More Related Content

What's hot (20)

Similar to A Hybrid DC-DC Converter for Standalone Applications (20)

More from IRJET Journal (20)

Recently uploaded (20)

A Hybrid DC-DC Converter for Standalone Applications