A Literature Review on Effect of Machining Parameters in Wire - EDM
4 likes1,609 views
The document discusses advancements in wire electrical discharge machining (WEDM) and its parameters affecting metal removal rate (MRR), surface roughness, and kerf width. It reviews multiple studies that utilize different methods, such as response surface methodology and Taguchi methods, to optimize WEDM performance on various materials including tool steel and titanium alloys. The findings highlight the significance of parameters like pulse on/off time, voltage, and wire speed in achieving optimal machining outcomes.
![IJSRD - International Journal for Scientific Research & Development| Vol. 1, Issue 9, 2013 | ISSN (online): 2321-0613
All rights reserved by www.ijsrd.com 1898
Abstract—The recent upgradation of newer and harder
materials has made the machining task in WEDM quite
challenging. Thus for the optimum use of all the resources it
is essential to make the optimum use of parameters to get
the best output to increase the productivity. Advances in
technology have impacted with an increased cutting speed
and tight tolerances in WEDM. This paper reviews the
various notable works in field of WEDM and magnifies on
effect of machining parameters on MRR, kerf width and
surface roughness.
Key words: Brass wires, coated wires, MRR, DOE, Surface
roughness, ANOVA
I. INTRODUCTION
Wire electrical discharge machining (WEDM) is an
indispensable machining technique for producing
complicated cut-outs through difficult to machine metals
without using high cost grinding or expensive formed tools
[9]. Wire-cutting EDM is commonly used when low residual
stresses are desired, because it does not require high cutting
forces for removal of material.
It can machine anything that is electrically
conductive regardless of the hardness, from relatively
common materials such as tool steel, aluminium, copper,
and graphite, to exotic space-age alloys including hast alloy,
wasp alloy, Inconel, titanium, carbide, polycrystalline
diamond compacts and conductive ceramics. Parts that have
complex geometry and tolerances don't require you to rely
on different skill levels or multiple equipments. Most work
pieces come off the machine as a finished part, without the
need for secondary operations.
II. WORKING PRINCIPLE OF WIRE - EDM
A model of Wire EDM is shown in figure 1. In Wire EDM,
the conductive materials are machined with a series of
electrical discharges (sparks) that are produced between an
accurately positioned moving wire (the electrode) and the
work piece. High frequency pulses of alternating or direct
current is discharged from the wire to the work piece with a
very small spark gap through an insulated dielectric fluid
(water). Wire EDM uses a travelling wire electrode that
passes through the work piece. The wire is monitored
precisely by a computer-numerically controlled (CNC)
system.
Many sparks can be observed at one time. This is
because actual discharges can occur more than one hundred
thousand times per second, with discharge sparks lasting in
the range of 1/1,000,000 of a second or less. The volume of
metal removed during this short period of spark discharge
depends on the desired cutting speed and the surface finish
required.
Fig. 1: Wire EDM model
The most important performance measures in WEDM are
metal removal rate, surface finish, and cutting width. They
depend on machining parameters like discharge current,
pulse duration, pulse frequency, wire speed, wire tension
and dielectric flow rate. Among other performance
measures, the kerf, which determines the dimensional
accuracy of the finishing part, is of extreme importance. The
internal corner radius to be produced in WEDM operations
is also limited by the kerf. The gap between the wire and
work piece usually ranges from 0.025 to 0.075 mm and is
constantly maintained by a computer controlled positioning
system.
III. LITERATURE REVIEW
S. B. Prajapati, N. S. Patel [1] evaluates the effect of pulse
On-Off time, voltage, wire feed and wire tension on MRR,
SR, kerf and gap current in Wire EDM. A series of
experiments have been performed on AISI A2 tool steel in
form of a square bar. Analysis of data optimization and
performance is done by Response Surface Methodology
(RSM).
Atul J. Patel, Prof. Satyam Patel [2] used Taguchi
L9 orthogonal array to find out effects on AISI 304 Stainless
Steel of thickness 10 mm in Wire EDM. Input parameters
such as pulse On-Off time, wire tension and input power
have been used to evaluate their influence on Surface
Roughness and Material Removal Rate. Mathematical
relations between input parameters and performance
characteristics were established by the linear regression
analysis method by using MINITAB software.
Rao and Sarcar [3] studied the influence of optimal
parameters on cutting speed, surface roughness, spark gap,
and material removal rate (MRR). He evaluated the optimal
parameters such as discharge current, voltage at rated wire
speed and tension for brass electrode of size 5-80 mm.
Mathematical relation was developed for cutting speed,
spark gap and MRR. Effect of wire material on cutting
A Literature Review on Effect of Machining Parameters in Wire – EDM
Rutvik A. Shah1
Prof. Ankit Darji2
1
P. G. Student (M. E. - Production) 2
Asst. Professor
1, 2
Mechanical Engineering Department
1, 2
LDRP-ITR, Gandhinagar, Gujarat](https://image.slidesharecdn.com/ijsrdv1i9051-140812034940-phpapp01/85/A-Literature-Review-on-Effect-of-Machining-Parameters-in-Wire-EDM-1-320.jpg)
![A Literature Review on Effect of Machining Parameters in Wire - EDM
(IJSRD/Vol. 1/Issue 9/2013/0051)
All rights reserved by www.ijsrd.com 1899
criteria was also evaluated for brass work piece with four
wires of different copper percentages. This study is useful
for evaluating cutting time for any size of job and to set
parameters for required surface finish for high accuracy of
cutting. Mathematical relations are helpful for estimating
cutting time, cost of machining, process planning and
accuracy of cutting for any size of job within machine range.
Results obtained are helpful for quantification of parameters
for quality cuts. Also, results are useful in manufacturing
wire EDM system for die and tool steel electrodes.
Nihat, Can, Gul [4] investigated on the effect and
optimization of machining parameters on kerf and material
removal rate (MRR) in WEDM operations. Experimental
studies were conducted using different pulse duration, open
circuit voltage, wire speed, and dielectric flushing pressure.
Importance levels of parameters were analysed using
analysis of variance (ANNOVA). The optimum machining
parameter combination was obtained by using the analysis
of signal-to-noise (S/N) ratio. The variation of kerf and
MRR with machining parameters is mathematically
modelled by using regression analysis method. Objective of
minimum kerf together with maximum MRR was
performed. The experimental studies were performed on a
Sodick A320D/EX21 WEDM machine tool. CuZn37 Master
Brass wire with 0.25mm diameter was used in the
experiments. As work piece material, AISI 4140 steel (DIN
42CrMo4) with 200mm × 40mm × 10mm size was used.
S. B. Prajapati, N. S. Patel, V D Asal [5] studied
the effect of process parameter like Pulse ON time, Pulse
OFF time, Voltage, Wire Feed and Wire Tension on MRR,
SR, Kerf and Gap current. Output parameters of Wire EDM
of AISI A2 Tool Steel are predicted by using Artificial
Neural Network (ANN). ANN was founded a powerful tool
for data prediction and it gives agreeable result when
Experimental and Predicted Data were compared. Taguchi
method is used for Design of Experiment. The control
factors considered for the study are Pulse-on, Pulse- off, Bed
speed and Current. Three levels for each control factor were
used. Based on number of control factors and their levels,
L27 orthogonal array (OA) was selected for data collection.
From Comparison of Experimental result and ANN
Predicted result it was found that they were very close and
error was very less. The maximum error is 0.14. ANN is
powerful technique for prediction of process parameters
giving very accurate result.
Kuriachen Basil, Dr. Josephkunju Paul, Dr. Jeoju
M.Issac [6] investigates the effect of voltage, dielectric
pressure, pulse on-time and pulse off-time on spark gap of
Ti6AL4V alloy. It has been found that pulse on time and
pulse off time have the more impact on the spark gap. The
minimum spark gap was obtained as 0.040407mm. The
WEDM experiments were conducted in Electronic ultra-cut
S1 machine using 0.25 mm brass wire as the tool electrode.
‘Pulse on time’, ‘pulse off time’, ‘voltage’ and ‘dielectric
pressure’ are the four WEDM parameters that were selected
for investigations. In this experimental study two level full
factorial experiment is adopted because this gives all
possible combinations of machine parameters. It can be
noticed that corresponding to minimum value of pulse off
time the spark gap decreases with increase in dielectric
pressure, whereas the spark gap increases with increase in
dielectric pressure corresponding to maximum value of
pulse off time.
Aniza Alias, Bulan Abdullah, Norliana Mohd
Abbas [7] aims to investigate the influence of feed rate on
the performance of WEDM on Titanium Ti-Al-4V. Brass
wire was employed as the electrode for the investigation.
The best combination of machining parameter viz. machine
feed rate (4 mm/min), wire speed (8 m/min), wire tension
(1.4kg) and voltage (60V) were identified. The selection of
parameters depends on the requirements based on a better
surface roughness or a maximum material removal rate.
Hence an appropriate combination of variables can be
selected accordingly. Furthermore, this combination can
contributes to increase production rates perceptibly by
reducing machining time. The outcome of this study will
help in improving the quality of Titanium Ti-6Al-4V
products as well as minimizing the machining cost to realize
the economic potential to the fullest.
Pujari Srinivasa Rao, Koona Ramji, Beela
Satyanarayana [8] studied Wire-cut electric discharge
machining of Aluminum-24345. Experimentation has been
done by using Taguchi’s L18 (21x37) orthogonal array
under different conditions of parameters. The response of
surface roughness is considered for improving the
machining efficiency. Optimal combinations of parameters
were obtained by this method. The confirmation experiment
shows, the significant improvement in surface finish
(1.03μm) was obtained with this method. Multiple linear
regression model have been developed relating the process
parameters and machining performance and a high
correlation coefficient (r2 = 0.97) indicates the suitability of
the proposed model in predicting surface roughness. The
study shows that with the minimum number of experiments
the stated problem can be solved when compared to full
factorial design. All the experiments were conducted on
Ultra Cut 843/ ULTRA CUT f2 CNC Wire-cut EDM
machine. The size of the work piece considered for
experimentation on the wire-cut EDM is 25 mm x 20 mm x
10 mm. Increasing the discharge energy generally increases
surface irregularities due to much more melting and re-
solidification of materials. Hence, it is found that SR tends
to decrease significantly with decrease in IP and TON.
Saurav Datta, Siba Sankar Mahapatra [9]
experimented with six process parameters: discharge
current, pulse duration, pulse frequency, wire speed, wire
tension and dielectric flow rate; to be varied in three
different levels. Data related to the process responses viz.
material removal rate (MRR), roughness value of the
worked surface and kerf have been measured for each of the
experimental runs; which correspond to randomly chosen
different combinations of factor setting. These data have
been utilized to fit a quadratic mathematical model
(Response Surface Model) for each of the responses, which
can be represented as a function of the aforesaid six process
parameters. Predicted data have been utilized for
identification of the parametric influence in the form of
graphical representation for showing influence of the
parameters on selected responses. Predicted data given by
the models (as per Taguchi’s L27 (3*6) Orthogonal Array
(OA) design) have been used in search of an optimal
parametric combination to achieve desired yield of the](https://image.slidesharecdn.com/ijsrdv1i9051-140812034940-phpapp01/85/A-Literature-Review-on-Effect-of-Machining-Parameters-in-Wire-EDM-2-320.jpg)
![A Literature Review on Effect of Machining Parameters in Wire - EDM
(IJSRD/Vol. 1/Issue 9/2013/0051)
All rights reserved by www.ijsrd.com 1900
process: maximum MRR, good surface finish and
dimensional accuracy of the product. Grey relational
analysis has been adopted to convert this multi-objective
criterion into an equivalent single objective function. The
work piece, a block of D2 tool steel with 200 mm × 25 mm
×10 mm size, has been cut 100 mm length with 10 mm
depth along the longer length.
IV. CONCLUSION
1) For cutting rate and surface roughness, the pulse ON and
pulse OFF time is most significant. The spark gape set
voltage is significant for kerf.
2) Increase in Input power, value of surface roughness is
increase. Increase in Pulse on time, value of material
removal rate is increase.
3) Open circuit voltage was three times more important
than pulse duration for controlling kerf, while for MRR,
open circuit voltage was about six times more important
than pulse duration.
4) Corresponding to minimum value of pulse off time the
spark gap decreases with increase in dielectric pressure,
whereas the spark gap increases with increase in
dielectric pressure corresponding to maximum value of
pulse off time.
5) As the machine feed rate increases, the kerf width
decreases. Increasing machine feed rate, the MRR will
increases simultaneously. Smoother surface can be
obtained with low setting of machine feed rate.
6) It is found that SR tends to decrease significantly with
decrease in IP and TON.
V. FUTURE SCOPE
For researchers there is wide scope for analysing and
developing new technology. Many different types of wire
material can be used for machining on a particular material
and optimum parameters can be obtained. Also many
different work piece materials that can be used for research
are Tool Steels, Titanium alloys, EN series, Inconel, Nickel
alloys, Aluminium alloys etc.
REFERENCES
[1] S. B. Prajapati, N. S. Patel, 2013. Effect of process
parameters on performance measures of Wire EDM for
AISI A2 Tool Steel. International Journal of
Computational Engineering Research||Vol, 03||Issue, 4||.
[2] Atul J. Patel, Prof. Satyam Patel, Parametric
optimization of Wire cut EDM machine on hard steel
alloy with multiple quality characteristics. Patel et al.,
International Journal of Advanced Engineering
Technology E-ISSN 0976-3945.
[3] C V S Parameswara Rao and M MM Sarcar, Evaluation
of optimal parameters for machining brass with Wire
cut EDM. Journal of Scientific and Industrial Research
Vol. 68, January 2009, pp. 32-35.
[4] Nihat Tosun, Can Cogun and Gul Tosun, A study on
kerf and material removal rate in wire electrical
discharge machining based on Taguchi method. Journal
of Materials Processing Technology 152 (2004) 316-
322.
[5] S. B. Prajapati, N. S. Patel, V D Asal. Prediction of
Process Parameters of Wire EDM for AISI A2 using
ANN. Volume: 3 | Issue: 5 | May 2013 | ISSN - 2249-
555X.
[6] Kuriachen Basil, Dr. Josephkunju Paul, Dr. Jeoju
M.Issac. Spark Gap Optimization of WEDM Process on
Ti6Al4V. ISSN: 2319-5967, ISO 9001:2008 Certified.
International Journal of Engineering Science and
Innovative Technology (IJESIT). Volume 2, Issue 1,
January 2013.
[7] Aniza Alias, Bulan Abdullah, Norliana Mohd Abbas.
WEDM: INFLUENCE OF MACHINE FEED RATE
IN MACHINING TITANIUM Ti-6Al-4V USING
BRASS WIRE AND CONSTANT CURRENT (4A).
International Symposium on Robotics and Intelligent
Sensors 2012 (IRIS 2012).
[8] Pujari Srinivasa Rao, Koona Ramji, Beela
Satyanarayana. EFFECT OF WEDM CONDITIONS
ON SURFACE ROUGHNESS: A PRAPMETRIC
OPTIMISATION USING TAGUCHI METHOD.
IJAEST, Vol No. 6, Issue No. 1, 041 – 048.
[9] Saurav Datta, Siba Sankar Mahapatra. Modelling,
simulation and parametric optimization of wire EDM
process using response surface methodology coupled
with grey-Taguchi technique. Vol. 2, No. 5, 2010.](https://image.slidesharecdn.com/ijsrdv1i9051-140812034940-phpapp01/85/A-Literature-Review-on-Effect-of-Machining-Parameters-in-Wire-EDM-3-320.jpg)
A Literature Review on Effect of Machining Parameters in Wire - EDM
- 1. IJSRD - International Journal for Scientific Research & Development| Vol. 1, Issue 9, 2013 | ISSN (online): 2321-0613 All rights reserved by www.ijsrd.com 1898 Abstract—The recent upgradation of newer and harder materials has made the machining task in WEDM quite challenging. Thus for the optimum use of all the resources it is essential to make the optimum use of parameters to get the best output to increase the productivity. Advances in technology have impacted with an increased cutting speed and tight tolerances in WEDM. This paper reviews the various notable works in field of WEDM and magnifies on effect of machining parameters on MRR, kerf width and surface roughness. Key words: Brass wires, coated wires, MRR, DOE, Surface roughness, ANOVA I. INTRODUCTION Wire electrical discharge machining (WEDM) is an indispensable machining technique for producing complicated cut-outs through difficult to machine metals without using high cost grinding or expensive formed tools [9]. Wire-cutting EDM is commonly used when low residual stresses are desired, because it does not require high cutting forces for removal of material. It can machine anything that is electrically conductive regardless of the hardness, from relatively common materials such as tool steel, aluminium, copper, and graphite, to exotic space-age alloys including hast alloy, wasp alloy, Inconel, titanium, carbide, polycrystalline diamond compacts and conductive ceramics. Parts that have complex geometry and tolerances don't require you to rely on different skill levels or multiple equipments. Most work pieces come off the machine as a finished part, without the need for secondary operations. II. WORKING PRINCIPLE OF WIRE - EDM A model of Wire EDM is shown in figure 1. In Wire EDM, the conductive materials are machined with a series of electrical discharges (sparks) that are produced between an accurately positioned moving wire (the electrode) and the work piece. High frequency pulses of alternating or direct current is discharged from the wire to the work piece with a very small spark gap through an insulated dielectric fluid (water). Wire EDM uses a travelling wire electrode that passes through the work piece. The wire is monitored precisely by a computer-numerically controlled (CNC) system. Many sparks can be observed at one time. This is because actual discharges can occur more than one hundred thousand times per second, with discharge sparks lasting in the range of 1/1,000,000 of a second or less. The volume of metal removed during this short period of spark discharge depends on the desired cutting speed and the surface finish required. Fig. 1: Wire EDM model The most important performance measures in WEDM are metal removal rate, surface finish, and cutting width. They depend on machining parameters like discharge current, pulse duration, pulse frequency, wire speed, wire tension and dielectric flow rate. Among other performance measures, the kerf, which determines the dimensional accuracy of the finishing part, is of extreme importance. The internal corner radius to be produced in WEDM operations is also limited by the kerf. The gap between the wire and work piece usually ranges from 0.025 to 0.075 mm and is constantly maintained by a computer controlled positioning system. III. LITERATURE REVIEW S. B. Prajapati, N. S. Patel [1] evaluates the effect of pulse On-Off time, voltage, wire feed and wire tension on MRR, SR, kerf and gap current in Wire EDM. A series of experiments have been performed on AISI A2 tool steel in form of a square bar. Analysis of data optimization and performance is done by Response Surface Methodology (RSM). Atul J. Patel, Prof. Satyam Patel [2] used Taguchi L9 orthogonal array to find out effects on AISI 304 Stainless Steel of thickness 10 mm in Wire EDM. Input parameters such as pulse On-Off time, wire tension and input power have been used to evaluate their influence on Surface Roughness and Material Removal Rate. Mathematical relations between input parameters and performance characteristics were established by the linear regression analysis method by using MINITAB software. Rao and Sarcar [3] studied the influence of optimal parameters on cutting speed, surface roughness, spark gap, and material removal rate (MRR). He evaluated the optimal parameters such as discharge current, voltage at rated wire speed and tension for brass electrode of size 5-80 mm. Mathematical relation was developed for cutting speed, spark gap and MRR. Effect of wire material on cutting A Literature Review on Effect of Machining Parameters in Wire – EDM Rutvik A. Shah1 Prof. Ankit Darji2 1 P. G. Student (M. E. - Production) 2 Asst. Professor 1, 2 Mechanical Engineering Department 1, 2 LDRP-ITR, Gandhinagar, Gujarat
- 2. A Literature Review on Effect of Machining Parameters in Wire - EDM (IJSRD/Vol. 1/Issue 9/2013/0051) All rights reserved by www.ijsrd.com 1899 criteria was also evaluated for brass work piece with four wires of different copper percentages. This study is useful for evaluating cutting time for any size of job and to set parameters for required surface finish for high accuracy of cutting. Mathematical relations are helpful for estimating cutting time, cost of machining, process planning and accuracy of cutting for any size of job within machine range. Results obtained are helpful for quantification of parameters for quality cuts. Also, results are useful in manufacturing wire EDM system for die and tool steel electrodes. Nihat, Can, Gul [4] investigated on the effect and optimization of machining parameters on kerf and material removal rate (MRR) in WEDM operations. Experimental studies were conducted using different pulse duration, open circuit voltage, wire speed, and dielectric flushing pressure. Importance levels of parameters were analysed using analysis of variance (ANNOVA). The optimum machining parameter combination was obtained by using the analysis of signal-to-noise (S/N) ratio. The variation of kerf and MRR with machining parameters is mathematically modelled by using regression analysis method. Objective of minimum kerf together with maximum MRR was performed. The experimental studies were performed on a Sodick A320D/EX21 WEDM machine tool. CuZn37 Master Brass wire with 0.25mm diameter was used in the experiments. As work piece material, AISI 4140 steel (DIN 42CrMo4) with 200mm × 40mm × 10mm size was used. S. B. Prajapati, N. S. Patel, V D Asal [5] studied the effect of process parameter like Pulse ON time, Pulse OFF time, Voltage, Wire Feed and Wire Tension on MRR, SR, Kerf and Gap current. Output parameters of Wire EDM of AISI A2 Tool Steel are predicted by using Artificial Neural Network (ANN). ANN was founded a powerful tool for data prediction and it gives agreeable result when Experimental and Predicted Data were compared. Taguchi method is used for Design of Experiment. The control factors considered for the study are Pulse-on, Pulse- off, Bed speed and Current. Three levels for each control factor were used. Based on number of control factors and their levels, L27 orthogonal array (OA) was selected for data collection. From Comparison of Experimental result and ANN Predicted result it was found that they were very close and error was very less. The maximum error is 0.14. ANN is powerful technique for prediction of process parameters giving very accurate result. Kuriachen Basil, Dr. Josephkunju Paul, Dr. Jeoju M.Issac [6] investigates the effect of voltage, dielectric pressure, pulse on-time and pulse off-time on spark gap of Ti6AL4V alloy. It has been found that pulse on time and pulse off time have the more impact on the spark gap. The minimum spark gap was obtained as 0.040407mm. The WEDM experiments were conducted in Electronic ultra-cut S1 machine using 0.25 mm brass wire as the tool electrode. ‘Pulse on time’, ‘pulse off time’, ‘voltage’ and ‘dielectric pressure’ are the four WEDM parameters that were selected for investigations. In this experimental study two level full factorial experiment is adopted because this gives all possible combinations of machine parameters. It can be noticed that corresponding to minimum value of pulse off time the spark gap decreases with increase in dielectric pressure, whereas the spark gap increases with increase in dielectric pressure corresponding to maximum value of pulse off time. Aniza Alias, Bulan Abdullah, Norliana Mohd Abbas [7] aims to investigate the influence of feed rate on the performance of WEDM on Titanium Ti-Al-4V. Brass wire was employed as the electrode for the investigation. The best combination of machining parameter viz. machine feed rate (4 mm/min), wire speed (8 m/min), wire tension (1.4kg) and voltage (60V) were identified. The selection of parameters depends on the requirements based on a better surface roughness or a maximum material removal rate. Hence an appropriate combination of variables can be selected accordingly. Furthermore, this combination can contributes to increase production rates perceptibly by reducing machining time. The outcome of this study will help in improving the quality of Titanium Ti-6Al-4V products as well as minimizing the machining cost to realize the economic potential to the fullest. Pujari Srinivasa Rao, Koona Ramji, Beela Satyanarayana [8] studied Wire-cut electric discharge machining of Aluminum-24345. Experimentation has been done by using Taguchi’s L18 (21x37) orthogonal array under different conditions of parameters. The response of surface roughness is considered for improving the machining efficiency. Optimal combinations of parameters were obtained by this method. The confirmation experiment shows, the significant improvement in surface finish (1.03μm) was obtained with this method. Multiple linear regression model have been developed relating the process parameters and machining performance and a high correlation coefficient (r2 = 0.97) indicates the suitability of the proposed model in predicting surface roughness. The study shows that with the minimum number of experiments the stated problem can be solved when compared to full factorial design. All the experiments were conducted on Ultra Cut 843/ ULTRA CUT f2 CNC Wire-cut EDM machine. The size of the work piece considered for experimentation on the wire-cut EDM is 25 mm x 20 mm x 10 mm. Increasing the discharge energy generally increases surface irregularities due to much more melting and re- solidification of materials. Hence, it is found that SR tends to decrease significantly with decrease in IP and TON. Saurav Datta, Siba Sankar Mahapatra [9] experimented with six process parameters: discharge current, pulse duration, pulse frequency, wire speed, wire tension and dielectric flow rate; to be varied in three different levels. Data related to the process responses viz. material removal rate (MRR), roughness value of the worked surface and kerf have been measured for each of the experimental runs; which correspond to randomly chosen different combinations of factor setting. These data have been utilized to fit a quadratic mathematical model (Response Surface Model) for each of the responses, which can be represented as a function of the aforesaid six process parameters. Predicted data have been utilized for identification of the parametric influence in the form of graphical representation for showing influence of the parameters on selected responses. Predicted data given by the models (as per Taguchi’s L27 (3*6) Orthogonal Array (OA) design) have been used in search of an optimal parametric combination to achieve desired yield of the
- 3. A Literature Review on Effect of Machining Parameters in Wire - EDM (IJSRD/Vol. 1/Issue 9/2013/0051) All rights reserved by www.ijsrd.com 1900 process: maximum MRR, good surface finish and dimensional accuracy of the product. Grey relational analysis has been adopted to convert this multi-objective criterion into an equivalent single objective function. The work piece, a block of D2 tool steel with 200 mm × 25 mm ×10 mm size, has been cut 100 mm length with 10 mm depth along the longer length. IV. CONCLUSION 1) For cutting rate and surface roughness, the pulse ON and pulse OFF time is most significant. The spark gape set voltage is significant for kerf. 2) Increase in Input power, value of surface roughness is increase. Increase in Pulse on time, value of material removal rate is increase. 3) Open circuit voltage was three times more important than pulse duration for controlling kerf, while for MRR, open circuit voltage was about six times more important than pulse duration. 4) Corresponding to minimum value of pulse off time the spark gap decreases with increase in dielectric pressure, whereas the spark gap increases with increase in dielectric pressure corresponding to maximum value of pulse off time. 5) As the machine feed rate increases, the kerf width decreases. Increasing machine feed rate, the MRR will increases simultaneously. Smoother surface can be obtained with low setting of machine feed rate. 6) It is found that SR tends to decrease significantly with decrease in IP and TON. V. FUTURE SCOPE For researchers there is wide scope for analysing and developing new technology. Many different types of wire material can be used for machining on a particular material and optimum parameters can be obtained. Also many different work piece materials that can be used for research are Tool Steels, Titanium alloys, EN series, Inconel, Nickel alloys, Aluminium alloys etc. REFERENCES [1] S. B. Prajapati, N. S. Patel, 2013. Effect of process parameters on performance measures of Wire EDM for AISI A2 Tool Steel. International Journal of Computational Engineering Research||Vol, 03||Issue, 4||. [2] Atul J. Patel, Prof. Satyam Patel, Parametric optimization of Wire cut EDM machine on hard steel alloy with multiple quality characteristics. Patel et al., International Journal of Advanced Engineering Technology E-ISSN 0976-3945. [3] C V S Parameswara Rao and M MM Sarcar, Evaluation of optimal parameters for machining brass with Wire cut EDM. Journal of Scientific and Industrial Research Vol. 68, January 2009, pp. 32-35. [4] Nihat Tosun, Can Cogun and Gul Tosun, A study on kerf and material removal rate in wire electrical discharge machining based on Taguchi method. Journal of Materials Processing Technology 152 (2004) 316- 322. [5] S. B. Prajapati, N. S. Patel, V D Asal. Prediction of Process Parameters of Wire EDM for AISI A2 using ANN. Volume: 3 | Issue: 5 | May 2013 | ISSN - 2249- 555X. [6] Kuriachen Basil, Dr. Josephkunju Paul, Dr. Jeoju M.Issac. Spark Gap Optimization of WEDM Process on Ti6Al4V. ISSN: 2319-5967, ISO 9001:2008 Certified. International Journal of Engineering Science and Innovative Technology (IJESIT). Volume 2, Issue 1, January 2013. [7] Aniza Alias, Bulan Abdullah, Norliana Mohd Abbas. WEDM: INFLUENCE OF MACHINE FEED RATE IN MACHINING TITANIUM Ti-6Al-4V USING BRASS WIRE AND CONSTANT CURRENT (4A). International Symposium on Robotics and Intelligent Sensors 2012 (IRIS 2012). [8] Pujari Srinivasa Rao, Koona Ramji, Beela Satyanarayana. EFFECT OF WEDM CONDITIONS ON SURFACE ROUGHNESS: A PRAPMETRIC OPTIMISATION USING TAGUCHI METHOD. IJAEST, Vol No. 6, Issue No. 1, 041 – 048. [9] Saurav Datta, Siba Sankar Mahapatra. Modelling, simulation and parametric optimization of wire EDM process using response surface methodology coupled with grey-Taguchi technique. Vol. 2, No. 5, 2010.