AC Generators
Download as PPT, PDF11 likes13,985 views
This document provides an overview of AC generators and their components. It discusses the basic principles of magnetic induction that AC generators rely on to produce power. It describes different types of AC generators like rotating armature and rotating field alternators. It also discusses the components of AC generators like the rotor, stator, field, and armature. Additionally, it covers practical AC generator concepts like prime movers, excitation, single and polyphase outputs, voltage control, and parallel operation of multiple generators. The document is intended to introduce the basic concepts and components of AC generators at an elementary level.
AC Generators
- 1. Elementary of Alternative Current AC Generators
- 2. INTRODUCTION • Most of the electrical power used aboard Navy ships and aircraft as well as in civilian applications is ac. As a result, the ac generator is the most important means of producing electrical power. Ac generators, generally called alternators, vary greatly in size depending upon the load to which they supply power. For example, the alternators in use at hydroelectric plants, such as Hoover Dam, are tremendous in size, generating thousands of kilowatts at very high voltage levels. Another example is the alternator in a typical automobile, which is very small by comparison. It weighs only a few pounds and produces between 100 and 200 watts of power, usually at a potential of 12 volts.
- 3. Navy Ship
- 4. Aircraft
- 5. Hoover Dam Black Canyon of the Colorado River, on the border between the US states of Arizona and Nevada
- 6. BASIC AC GENERATORS • Regardless of size, all electrical generators, whether dc or ac, depend upon the principle of magnetic induction. An emf is induced in a coil as a result of (1) a coil cutting through a magnetic field, or (2) a magnetic field cutting through a coil. As long as there is relative motion between a conductor and a magnetic field, a voltage will be induced in the conductor. That part of a generator that produces the magnetic field is called the field. That part in which the voltage is induced is called the armature. For relative motion to take place between the conductor and the magnetic field, all generators must have two mechanical parts — a rotor and a stator. The ROTor is the part that ROTates; the STATor is the part tha remains STATionary. In a dc generator, the armature is always the rotor. In alternators, the armature may be either the rotor or stator.
- 7. Types of AC Generators ROTATING ARMATURE-ALTERNATOR The ROTATING ARMATURE-ALTERNATOR •is essentially a loop rotating through a stationary magnetic fealties cutting action of the loop through the magnetic field generates ac in the loop. This ac is removed from the loop by means of slip rings and applied to an external load.
- 8. Types of AC Generators ROTATING-FIELD ALTERNATOR The ROTATING-FIELD ALTERNATOR •has a stationary armature and a rotating field. High voltages can be generated in the armature and applied to the load directly, without the need of slip rings and brushes. The low dc voltage is applied to the rotor field by means of slip rings, but this does not introduce any insulation problems.
- 9. PRACTICAL ALTERNATORS • The alternators described so far in this chapter are ELEMENTARY in nature; they are seldom used except as examples to aid in understanding practical alternators. • The remainder of this chapter will relate the principles of the elementary alternator to the alternators actually in use in the civilian community, as well as aboard Navy ships and aircraft. The following paragraphs in this chapter will introduce such concepts as prime movers, field excitation, armature characteristics and limitations, single-phase and polyphase alternators, controls, regulation, and parallel operation.
- 10. FUNCTIONS OF ALTERNATOR COMPONENTS • A typical rotating-field ac generator consists of an alternator and a smaller dc generator built into a single unit. The output of the alternator section supplies alternating voltage to the load. The only purpose for the dc exciter generator is to supply the direct current required to maintain the alternator field. This DC generator is referred to as the exciter.
- 11. Ac generator pictorial and schematic drawings
- 12. PRIME MOVERS • All generators, large and small, ac and dc, require a source of mechanical power to turn their rotors. This source of mechanical energy is called a prime mover. • Prime movers are divided into two classes for generators-high-speed and low-speed. Steam and gas turbines are high-speed prime movers, while internal-combustion engines, water, and electric motors are considered low-speed prime movers. • The type of prime mover plays an important part in the design of alternators since the speed at which the rotor is turned determines certain characteristics of alternator construction and operation.
- 13. ALTERNATOR ROTORS • There are two types of rotors used in rotating-field alternators. They are called the turbine-driven and salient-pole rotors.
- 14. Turbine-driven & Salient-pole • As you may have guessed, the turbine-driven rotor shown in figure 3-4, view A, is used when the prime mover is a high-speed turbine. The windings in the turbine-driven rotor are arranged to form two or four distinct poles. The windings are firmly embedded in slots to withstand the tremendous centrifugal forces encountered at high speeds. • The salient-pole rotor shown in figure 3-4, view B, is used in low- speed alternators. The salient-pole rotor often consists of several separately wound pole pieces, bolted to the frame of the rotor.
- 15. • If you could compare the physical size of the two types of rotors with the same electrical characteristics, you would see that the salient-pole rotor would have a greater diameter. At the same number of revolutions per minute, it has a greater centrifugal force than does the turbine-driven rotor. To reduce this force to a safe level so that the windings will not be thrown out of the machine, the salient pole is used only in low-speed designs. -4.—Types of rotors used in tors.
- 16. ALTERNATOR CHARACTERISTICS AND LIMITATIONS • Alternators are rated according to the voltage they are designed to produce and the maximum current they are capable of providing. The maximum current that can be supplied by an alternator depends upon the maximum heating loss that can be sustained in the armature. This heating loss (which is an I2 R power loss) acts to heat the conductors, and if excessive, destroys the insulation. Thus, alternators are rated in terms of this current and in terms of the voltage output — the alternator rating in small units is in volt-amperes; in large units it is kilovolt-amperes.
- 17. SINGLE-PHASE ALTERNATORS • A generator that produces a single, continuously alternating voltage is known as a SINGLE-PHASE alternator. • has an armature that consists of a number of windings placed symmetrically around the stator and connected in series. The voltages generated in each winding add to produce the total voltage across the two output terminals.
- 18. SINGLE-PHASE ALTERNATORS • Power that is used in homes, shops, and ships to operate portable tools and small appliances is single-phase power. Single-phase power alternators always generate single-phase power.
- 19. TWO-PHASE ALTERNATOR • Two phase implies two voltages if we apply our new definition of phase. And, it's that simple. A two-phase alternator is designed to produce two completely separate voltages. Each voltage, by itself, may be considered as a single-phase voltage. Each is generated completely independent of the other.
- 20. TWO-PHASE ALTERNATOR • consists of two phases whose windings are so placed around the stator that the voltages generated in them are 90ºout of phase.
- 21. TWO-PHASE ALTERNATOR CONNECTIONS • may be modified so that the output of a two- phase alternator is in a three-wire manner, which actually provides three outputs, two induced phase voltages, plus a vectorial sum voltage.
- 22. THREE-PHASE ALTERNATORS • In THREE-PHASE ALTERNATORS the windings have voltages generated in them which are120ºout of phase. Three-phase alternators are most often used to generate ac power.
- 23. THREE-PHASE ALTERNATOR CONNECTIONS • may be delta or wye connections depending on the application. The ac power aboard ship is usually taken from the ship's generators through delta connections, for the convenience of step-down transformers.
- 24. PRINCIPLES OF AC VOLTAGE CONTROL • In an alternator, an alternating voltage is induced in the armature windings when magnetic fields of alternating polarity are passed across these windings. The amount of voltage induced in the windings depends mainly on three things: • (1) the number of conductors in series per winding • (2) the speed (alternator rpm) at which the magnetic field cuts the winding, and • (3) the strength of the magnetic field. Any of these three factors could be used to control the amount of voltage induced in the alternator windings.
- 25. PARALLEL OPERATION OF ALTERNATORS • Alternators are connected in parallel to • (1) increase the output capacity of a system beyond that of a single unit, • (2) serve as additional reserve power for expected demands, or • (3) permit shutting down one machine and cutting in a standby machine without interrupting power distribution.
- 26. • When alternators are of sufficient size, and are operating at different frequencies and terminal voltages, severe damage may result if they are suddenly connected to each other through a common bus. To avoid this, the machines must be synchronized as closely as possible before connecting them together. • This may be accomplished by connecting one generator to the bus (referred to as bus generator), and then synchronizing the other (incoming generator) to it before closing the incoming generator's main power contactor. The generators are synchronized when the following conditions are set: 1.Equal terminal voltages. This is obtained by adjustment of the incoming generator's field strength. 2.Equal frequency. This is obtained by adjustment of the incoming generator's prime-mover speed. 3.Phase voltages in proper phase relation. The procedure for synchronizing generators is not discussed in this chapter. At this point, it is enough for you to know that the above must be accomplished to prevent damage to the machines.
- 27. Thank you for Listening Godbless