Access control-installation

Access Control Series Installation
Installation Guide

About this Guide
 The Access Control Station User guide is designed to provide information to
install the F& SC serial Access Control Station, for operation and configuration,
please refer to the corresponding user’s manual.
 Not all function these guides introduce available in combination,
all is option.
 About your machine function, please consult our company
technical personnel or the sales personnel.
Information in this document is subject to change without notice.

Access Control Station Installation Guide
- -2
Contents
1.
1 Before Installing .................................................................................1
1.1 Notice about installing.............................................................1
2System Configuration..........................................................................4
2.1 The illustration of system construction....................................4
2.2 The sketch map of communication..........................................5
3.Installation..........................................................................................6
3.1 Fixing mounting plate..............................................................6
3.2.1 Door Sensor..................................................................9
3.2.2 Release Button..............................................................9
3.2.3 Alarm ............................................................................9
3.2.4Conntion with lock ......................................................10
3.2.5 Ethernet connection ....................................................15
3.2.6 Connection with RS232..............................................17
3.2.7 Connection with RS485..............................................17
3.2.8 Wiegand output...........................................................19
3.2.9 Power connection........................................................20
3.2.9 Connect with external Weigend reader.......................20
3.3Fixing Access Control Station ................................................21
4. Fastening Access Control Station ....................................................22
5. Others ..............................................................................................23
5.1 Reset ......................................................................................23
5.2 Anti-dismantle button ............................................................23
5.3 Cable doorbell........................................................................24

- -1
1 Before Installing
1.1 Notice about installing
Access Control Station is a mass-produced product. It strictly tested
comply with the standard of China, U.S.A, and EU. This file contains
important information. It is better for you to read it carefully prior to
use. If you ignore it, the incorrect installation may cause the unit
damage. Although we could do our best to offer you service, the
neglect to the file could cause unwanted cost for you.
1. Before installation, please make sure the power is cut off, because it
is very dangerous if the power is on. The short circuit of power cable
may cause the core parts damage.
2. All exposed part of connection wire end cannot be exceeded 5mm to
prevent the bared wire accidental connection which leads to machine
break down. And also suggest using different color cable to connect.
3. In the place where the static is strong or in winter, please connect the
grounding firstly, in order to prevent the instant mass static damage the
machine.
4. Connect power supply with device in the last for the wiring
connection. If you find any unusual thing occur, please firstly cut off
the power, then go to examine. Keep in mind: wiring operation under
power on will lead to machine sudden damage; we are not liable for
damages and trouble due to such operation.
5. The height to mount device is about 1.4-1.5 meter

- -2
After installation, please take off protection film on the fingerprint sensor to
get best recognize result.
6. After installation finish, when go to test the exit-door button, please
keep a personal in the outside, because sometimes the accidental issue
can bring on you are not able to go outside.
7. Our equipment offer an automatically function, please after the installing
finish. Run the auto-test function to confirm the installation finish.
8.We recommend using above the 12V/3A direct-current supply for
ZK software’s access control device, electricity lock better to powered
by 12VDC, and no more than 1.5 A electric current At this time, the
electric current of supply should be above1A than lock power. If the
parameter of lock power surpasses this scope, please connect technical
personnel. If the power had not met above requests, it possibly causes
to be unable normally to drive the electricity lock, even damage the
device.
9. Before device to be connected please read and always follow "Quick
connect Guide" closely. Because the wrong wiring will cause the core
block and sensor to burn out, insult in device to break down, at this
cause ZK Software is not liable for any damages and trouble.
10. If the space between power adapters and device is too long, please
do not use the twisted-pair or other type ferrules for the power wire.
When the power wire is choused, you should consider attenuation of
voltage, which has passed long distance transfer.
11. Please use specialized RS485 cable and the RS232/485 converter
with power to hookup the network, the bus structure apply to connect
with each device. When a long cable is used to transfer signal, it is
need to connect a matching resistance to receiver, and its value is

- -3
120Ώ.
12. Other more details items; please see also the user manual, the
operating instructions and the appendix and so on.

- -4
2System Configuration
2.1 The illustration of system construction

- -5
2.2 The sketch map of communication
Access Control Station directly connects with PC through RS232 or TCP/IP
Access Control Station connects with PC through RS485 network
3 Access Control Station connects with PC through TCP/IP network．

- -6
3.Installation
3.1 Fixing mounting plate
①Take out a Access Control Station，dismantle the screw between machine
body and mounting plate until it is out, see figure (1).
②Carefully take up the bottom of mounting plate, see figure (2), push it up,
see figure (3), then take away the mounting plate.
③Determine the position of mounting plate on the wall. The Access Control
Station should be mounted on the external wall of the door approximately
1400mm from the ground to the unit bottom. After the position is determined,
you could drill a hole (18mm*20mm) for cable out, see below figure shadowed
part.
④Make the hole of mounting plate meet the drilled hole on the wall, Use the
screw to fix it on the wall, (for the details please see following figure)
⑤after installation, please make sure the mounting plate is reliable, fasten, not
loosed.

- -7
3.2Connect with peripheral equipment
Caution: Do not to connect peripheral equipment before the power of the
device is cut down, otherwise it is possible to damage the device badly.
Please follow instruction to connect peripheral equipment
① Door sensor connection（sensor, GND）
② Exit-button connection（Button GND）
③ Alarm connection（Alarm+, Alarm-）
④ Door lock connection（NC, COM, NO ）
⑤ Ethernet connection（ RJ45-1, RJ45-2, RJ45-3,RJ45-4）
⑥ RS232 connection（232RX, 232TX, GND ）
⑦ RS485 connection（485A,485B ）
⑧ Wiegand output connection（WD0,WD1,GND ）
⑨ Cable Bell (Bell+, Bell-)
⑩ Power connection (GND, +12V)
Cable socket

- -8
The definition of socket without Wiegand input
The definition of socket with Wiegand input
RJ45-1
RJ45-2
RJ45-3
RJ45-6
WD0
WD1
GND
232RX
232 TX
GND
485 A
485 B
Alarm +
Alarm -
NC
COM
NO
Button
GND
Sensor
Bell+
Bell-
GND
+12V
Spare
Spare
Spare
WD1
WD0
GND
+12V
Jump

- -9
3.2.1 Door Sensor
The door sensor is used to detect the door open-close status, Access Control
Station can monitor if the door has been unauthorized open through the door
sensor, at this time it can output a alarm signal, moreover, Access Control
Station can trigger prompt warning if after surpassing a timed period, the door
still open.
3.2.2 Release Button
The exit-button is installed for in-door operation. When the switch of the
button is close, the door will open. The distance is approximately 1400mm
from ground to exit-button bottom. Make sure that the exit-button position is
to align correct, upright and the connection is accurate and reliable. (Unused
exposed end of cable should be cut off, and use insulating tape to wrap it.) Pay
attention to electromagnetic disturbance. (For example: The light switch, the
computer and so on)
3.2.3 Alarm
Access Control Station alarm output is a switch signal，it is able to connect
with simple alarm by serial circuit, it also apply to top grade alarm and monitor
system as a trigger signal( this machine alarm function only support 12 VDC
Warner)

- -10
3.2.4Conntion with lock
The way of installing door lock depends on the type of lock and local condition.
Internal resistor, which comes from long distance transfer, should be taken into
consideration when selecting the cable of electric power. The door lock should
be installed reliable and stable. Ensure the wiring is correct. For the strike lock
and electromagnetic lock, you should pay attention to positive and negative
terminal connection. The unused bare end of wire should be cut off and use
insulating tape to wrap it. The delay time of strike lock is adjustable according
to different conditions.
Normally close (NC), under normal state the equipment keeps up closed, if
force the equipment open, the circuit cut off, brings out the state change.
Normally Open (NO), under normally state the circuit is cut off, if force the
equipment open, the circuit will be closed, and produce a state change.
Power Ground（GND），Current loop ground
Input terminal of door sensor（Sensor，GND ）the input port of door sensor

- -11
accepts the signal which come from normally closed contact to detect the
door opening and closing state, when the door is in closed, the contact keep in
closed state, if the door is opened by someone , the circuit break, thus bring out
state change. If unauthorized user opens this door or opening time is too long,
the controller will send alarm
Input terminal of release door button（Button， GND）The input port of
release door button accepts the signal which come from normally opened
contact to indicate that somebody want to go out, the input equipment such
as “ action detector”, “ press sensitivity floor board” or exit-door button all
serve as source to send signal，if nobody send out request to want to go out, the
input keep disconnection , if somebody want to go out, they trigger release
door button, the circuit is closed. Produce state change, the controller
responded to the request, unlock and permit door serve as passage mode.
Note：the process of performance to unlock door is control by relay, when you
install door lock, there are two thing you must think about, -- safety and
security , in other words, do you want which result that is if lose control of
this door, the door is still in safety—“lost control but safety” or if lose control
of this door, the door still is security--- “ lost control but security”
“Lost control but safety” is that the power supply cut off (maybe the power
supply is cut or the controller lose control of itself, the door will be open
automatically, and permit everybody freely to pass in and out, the door is not
ability to be closed until the system power on, these type of doors are installed
in the protective area which ensure everybody is able to pass in and out. One
representative application of “ lost control but safety” is to use

- -12
electromagnetism lock, under normal power supply, the door is controlled by
the controller, once the power supply break off, the electromagnetism lock will
lose magnetism and does not take effect, the door become a passage mode
“Lost control but security” is that the power supply cut off, the door will be
locked automatically, do not permit external personal to come in, but permit
internal personal go out, the door is not to be unlocked until the system power
supply is in gear. Make sure that the door of “lost control but security” will be
installed in the area, which needs to be protected through fair and foul. One
representative application of “ lost control but security” is to use electrical lock,
if the power supply break off, the external personal is not able to open the door,
but the internal person can open the by manual operation.
In the following three cases, we recommend that fingerprint machine and lock
be powered separately.
1) The working voltage of the lock is DC12V, but the current difference of the
fingerprint machine and the lock doesn’t exceed 1A.
2) The lock voltage is not DC12V.
3) The distance between lock and fingerprint machine is too far.
1、NC lock connection（Access Control Station and lock power by one adapter
together , Jump 2,3 pin closed）.

- -13
2、NO lock connection （Access control Station and lock powered by one
adapter together , Jump 2.3 pin closed）.
3、the output relay signal by Access control station, NC lock connection
（Access Control Station and lock powered by independent adapters jump
1,2 closed）

- -14
4、the output relay signal by Access control station, NO lock connection
( Access Control station and lock powered by independent adapter

- -15
3.2.5 Ethernet connection
1）Access Control Station connects with PC through cross cable
2）Access Control Station connects with PC through network and HUB to
create a local network
3) RJ45 plug wiring diagrams for Ethernet

- -16
a) RJ45 plug standard
b) Ethernet 10/100Base—T Crossover Cable
mostly apply to HUB and Switch ， or directly connect two Ethernet
terminals(not through HUB), fully support 10Base-T and 100Base-TX.
Plug1 Pin Pin Plug 2
TX+ 1 <——> 3 RX+
TX- 2 <——> 6 RX-
RX+ 3 <——> 1 TX+
RX- 6 <——> 2 TX-
c) Ethernet 10/100Base-T Straight Thru Cable
Support 10Base-T and 100Base-TX，apply to connect with network card and
HUB（or network outlet），sometime it is called (whips)”
Wiring standard Pin Color Pin Wiring standard
TX+ 1 <— white orange —> 1 TX+
TX- 2 <— Orange —> 2 TX-
RX+ 3 <— white green —> 3 RX+
4 <— Blue —> 4
5 <— Blue white —> 5
RX- 6 <— Green —> 6 RX-
7 <— White brown —> 7
8 <— Brown —> 8

- -17
3.2.6 Connection with RS232
The definition of PC connection with Access Control Station
PC Serial Port Access Control Station serial port
Pin2-Rxd Pin1-Txd（Purple）
Pin3-Txd Pin2-Txd（Yellow）
Pin5-Gnd Pin3-Gnd（Black）
3.2.7 Connection with RS485
The definition of terminal connection
Terminal Function
Pin1-485A（Green） RS-485 communication +
Pin2-485B（White） RS-485 communication -

- -18

- -19
3.2.8 Wiegand output
Access Control Station provide standard Wiegand 26 output, which can be
connected to most of access controllers, like the way of connecting with a ID
reader or password keyboard. The distance from the controller to device cannot
be more than 15 meter (if the signal must be transferred much further or there
is a strong interference around, please adopt a Wiegand signal amplifier)
Mote: no matter the device is powered by access controller or not, the ground
ports of them have to be properly together to ensure the Wiegand transfer
reliable
Terminal Function
Pin1-WD0（Green） Output Wiegand data 0 signal
Pin2-WD1（White） Output Wiegand data 1 signal
Pin3-GND（Black） Ground

- -20
3.2.9 Power connection
This device is powered by 12VDC. Its current is approximately 50mA in the
ready work status and 400mA in the work status. The power is conducted along
with the terminal; you can use the 12V-4A-supply adapter that is provided
along with the device. The detail about connection is as follow.
Terminal Function
Pin1-PWR（Red） Power positive
Pin2-GND（Black） Power negative
The following figure is an example, which takes a provided power adapter to
connect
3.2.9 Connect with external Weigend reader
Access control device whit the Weigand input function is able to connect with
card reader, which is located in outdoor or indoor, control the door by the
controller together, the cable which between access controller and external card
reader is no more than 90 meter.

- -21
3.3Fixing Access Control Station
① Confirm all connection plugs correctly.
② Align back iron-plate of Access Control Station body to mounting plate
properly, and push it up, see figure1, then push device backward, see
figure 2.
③ Turn and tie up the screw bottom.
After finishing installation, make ensure the body of device is fixed tightly.
①
②

- -22
4. Fastening Access Control Station
After all system installation finished, make a test and examine prior to power
on, inspect whether the lock driver is OK or not, for more details, please see
“User Guide” and “Software Manual”
①the green LED begins to glitter after power up.
②enter menu-〉Option-〉 Auto-test.
③enter menu-〉User manage-〉User Enroll-〉Fingerprint Enroll，Enroll a
fingerprint, and use the fingerprint to test access control system and door lock..
④if there is no any problem. Please delete this enrolled fingerprint.

- -23
5. Others
5.1 Reset
Due to operation error or other accidence, which leads the machine not to work,
you can restart machine through reset key.
①take a small tool which diameter is no more than 2mm.
②find reset mark of “res” on the left small hole on the bottom of device, see
following figure.
③Use the tool plug into the hole refer to the picture on right, then plug out. The
machine is able to restart.
5.2 Anti-dismantle button
Anti-dismantle button is on middle of device, whose function is realized by
back-cover pressing the anti-dismantle button. When the device is being
dismantled, it will send an alarm signal through the terminal.
Reset key

- -24
5.3 Cable doorbell
There is a key which is remark as icon（） on the keypad , this key is
used for doorbell.
Put the doorbell in the proper place, press the doorbell key on the device,
please see circle marked, after the doorbell receive a signal, it will ring.
Note：Because the terminal and key our provided is used for cable doorbell,
must join the power into the electric round.
Door Bell

Access control-installation

More Related Content

What's hot (20)

Viewers also liked (13)

Similar to Access control-installation (20)

Recently uploaded (20)

Access control-installation