Advanced motion controls dprahie 015s400
0 likes173 views
This document provides information on the DigiFlex® PerformanceTM Servo Drive DPRAHIE-015S400. It can drive brushed and brushless motors in torque, velocity, or position mode. It features regenerative braking, space vector modulation for efficiency, and configurable inputs/outputs. It is designed for panel mounting and has protections like overcurrent and overtemperature.
Advanced motion controls dprahie 015s400
- 1. DigiFlex® Performance™ Servo Drive DPRAHIE-015S400 Description Power Range The DigiFlex® Performance™ (DP) Series digital servo drives are designed to drive brushed and brushless servomotors. These fully digital drives operate in torque, velocity, or position mode and employ Space Vector Modulation (SVM), which results in higher bus voltage utilization and reduced heat dissipation compared to traditional PWM. The drive can be configured for a variety of external command signals. Commands can also be configured using the drive’s built-in Motion Engine, an internal motion controller used with distributed motion applications. In addition to motor control, these drives feature dedicated and programmable digital and analog inputs and outputs to enhance interfacing with external controllers and devices. This DP Series drive features a single RS-232/RS-485 interface used for drive configuration and setup. Drive commissioning is accomplished using DriveWare® 7, available for download at www.a-m-c.com. All drive and motor parameters are stored in non- volatile memory. Peak Current 15 A (10.6 ARMS) Continuous Current 7.5 A (7.5 ARMS) Supply Voltage 100 - 240 VAC Features Four Quadrant Regenerative Operation Space Vector Modulation (SVM) Technology Fully Digital State-of-the-art Design Programmable Gain Settings Fully Configurable Current, Voltage, Velocity and Position Limits PIDF Velocity Loop PID + FF Position Loop Compact Size, High Power Density 16-bit Analog to Digital Hardware Built-in brake/shunt regulator On-the-Fly Mode Switching On-the-Fly Gain Set Switching MODES OF OPERATION Current Position Velocity Hall Velocity COMMAND SOURCE PWM and Direction Encoder Following Over the Network ±10 V Analog 24V Step and Direction Sequencing Indexing Jogging FEEDBACK SUPPORTED Halls Incremental Encoder ±10 VDC Position Auxiliary Incremental Encoder Tachometer (±10 VDC) INPUTS/OUTPUTS 3 High Speed Captures 4 Programmable Analog Inputs (16-bit/12-bit Resolution) 3 Programmable Digital Inputs (Differential) 7 Programmable Digital Inputs (Single-Ended) 4 Programmable Digital Outputs (Single-Ended) COMPLIANCES & AGENCY APPROVALS UL cUL CE Class A (LVD) CE Class A (EMC) RoHS ELECTROMATE Toll Free Phone (877) SERVO98 Toll Free Fax (877) SERV099 www.electromate.com sales@electromate.com Sold & Serviced By:
- 2. DigiFlex® Performance™ Servo Drive DPRAHIE-015S400 BLOCK DIAGRAM SELECTTX/TX– I/O InterfaceI/O Interface DriveLogicRS232/485InterfaceCONTROL MODULERX/RX– TX+ RX+ ISO GNDPAI-1,4 + (REF+) PAI-1,4 –(REF–) PDI-1,2,3,4,5,6,7 (STEP / DIR / CAP-A) INPUT COMMONPDI-8,9,10 + (PWM+ / DIR+ / AUX ENC A,B + / CAP-B,C+) PDO-1,2,3,4OUTPUT COMMON5k+5V10k+5V10k2.5k20k20k20kPAI-2,3SGN GNDPAI-2: 33kPAI-3: 500k3.75KPDI-8,9,10 –(PWM–/ DIR–/ AUX ENC A,B –/ CAP-B,C–) OUTPUT PULL-UP Motor FeedbackMotor Feedback MOT ENC A,B,I + MOT ENC A,B,I – HALL A,B,C + HALL A,B,C – 10k+5V20k+5V20k+5V10k+5V10k5kENC A,B,I + OUTENC A,B,I –OUTDC+ MOTOR AMOTOR BMOTOR CDC- POWER MODULEPower StageL1L2 (N) BRLOGIC+ LOGIC– Logic PowerShunt Reg. Information on Approvals and Compliances US and Canadian safety compliance with UL 508c, the industrial standard for power conversion electronics. UL registered under file number E140173. Note that machine components compliant with UL are considered UL registered as opposed to UL listed as would be the case for commercial products. Compliant with European CE for both the Class A EMC Directive 2004/108/EC on Electromagnetic Compatibility (specifically EN 61000-6-4:2007 and EN 61000-6-2:2005) and LVD requirements of directive 2006/95/EC (specifically EN 60204-1:2006), a low voltage directive to protect users from electrical shock. RoHS (Reduction of Hazardous Substances) is intended to prevent hazardous substances such as lead from being manufactured in electrical and electronic equipment. ELECTROMATE Toll Free Phone (877) SERVO98 Toll Free Fax (877) SERV099 www.electromate.com sales@electromate.com Sold & Serviced By:
- 3. DigiFlex® Performance™ Servo Drive DPRAHIE-015S400 SPECIFICATIONS Power Specifications Description Units Value Rated Voltage VAC (VDC) 240 (339) AC Supply Voltage Range VAC 100 - 240 AC Supply Minimum VAC 90 AC Supply Maximum VAC 264 AC Input Phases - 1 AC Supply Frequency Hz 50 - 60 DC Supply Voltage Range1 VDC 127 - 373 DC Bus Over Voltage Limit VDC 394 DC Bus Under Voltage Limit VDC 55 Logic Supply Voltage VDC 20 - 30 (@ 850 mA) Maximum Peak Output Current2 A (Arms) 15 (10.6) Maximum Continuous Output Current3 A (Arms) 7.5 (7.5) Max. Continuous Output Power @ Rated Voltage4 W 2415 Max. Continuous Power Dissipation @ Rated Voltage W 127 Internal Bus Capacitance μF 540 External Shunt Resistance Minimum Resistance5 Ω 25 Minimum Load Inductance (Line-To-Line)6 μH 600 Switching Frequency kHz 20 Maximum Output PWM Duty Cycle % 100 Low Voltage Supply Outputs - +5 VDC (250 mA) Control Specifications Description Units Value Communication Interfaces - RS-485/232 Command Sources - ±10 V Analog, 24V Step and Direction, Encoder Following, Over the Network, PWM and Direction, Sequencing, Indexing, Jogging Feedback Supported - ±10 VDC Position, Auxiliary Incremental Encoder, Halls, Incremental Encoder, Tachometer (±10 VDC) Commutation Methods - Sinusoidal, Trapezoidal Modes of Operation - Current, Hall Velocity, Position, Velocity Motors Supported - Closed Loop Vector, Single Phase (Brushed, Voice Coil, Inductive Load), Three Phase (Brushless) Hardware Protection - 40+ Configurable Functions, Over Current, Over Temperature (Drive & Motor), Over Voltage, Short Circuit (Phase-Phase & Phase-Ground), Under Voltage Programmable Digital Inputs/Outputs (PDIs/PDOs) - 10/4 Programmable Analog Inputs/Outputs (PAIs/PAOs) - 4/0 Primary I/O Logic Level - 24 VDC Current Loop Sample Time μs 50 Velocity Loop Sample Time μs 100 Position Loop Sample Time μs 100 Maximum Encoder Frequency MHz 20 (5 pre-quadrature) Internal Shunt Regulator - Yes Internal Shunt Resistor - No Mechanical Specifications Description Units Value Agency Approvals - CE Class A (EMC), CE Class A (LVD), cUL, RoHS, UL Size (H x W x D) mm (in) 177.495 x 123.393 x 44.450 (6.988 x 4.858 x 1.750) Weight g (oz) 894 (31.5) Heatsink (Base) Temperature Range7 °C (°F) 0 - 75 (32 - 167) Storage Temperature Range °C (°F) -40 - 85 (-40 - 185) Form Factor - Panel Mount Cooling System - Natural Convection IP Rating - IP10 +24V LOGIC Connector - 2-port, 5.08 mm spaced, enclosed, friction lock header AUX ENCODER Connector - 15-pin, high-density, male D-sub COMM Connector - 9-pin, female D-sub FEEDBACK Connector - 15-pin, high-density, female D-sub I/O Connector - 26-pin, high-density, female D-sub POWER Connector - 10-port, 5.08 mm spaced, enclosed, friction lock header Notes 1. Large inrush current may occur upon initial DC supply connection to DC Bus. 2. Capable of supplying drive rated peak current for 2 seconds with 10 second foldback to continuous value. Longer times are possible with lower current limits. 3. Continuous Arms value attainable when RMS Charge-Based Limiting is used. 4. P = (DC Rated Voltage) * (Cont. RMS Current) * 0.95. 5. ADVANCED Motion Controls recommends using an external fuse in series with the shunt resistor. A 3 amp motor delay fuse is typical. 6. Lower inductance is acceptable for bus voltages well below maximum. Use external inductance to meet requirements. 7. Additional cooling and/or heatsink may be required to achieve rated performance. ELECTROMATE Toll Free Phone (877) SERVO98 Toll Free Fax (877) SERV099 www.electromate.com sales@electromate.com Sold & Serviced By:
- 4. DigiFlex® Performance™ Servo Drive DPRAHIE-015S400 PIN FUNCTIONS +24V LOGIC - Logic Power Connector Pin Name Description / Notes I/O 1 LOGIC GND Logic Supply Ground GND 2 LOGIC PWR Logic Supply Input I AUX ENCODER - Auxiliary Feedback Connector Pin Name Description / Notes I/O 1 RESERVED Reserved - 2 RESERVED Reserved - 3 RESERVED Reserved - 4 PDI-8 + (PWM+ / AUX ENC A+ / CAP-B+) Programmable Digital Input or PWM or Auxiliary Encoder or High Speed Capture (For Single-Ended Signals Leave Negative Terminal Open) I 5 PDI-8 - (PWM- / AUX ENC A- / CAP-B-) I 6 PDI-9 + (DIR+ / AUX ENC B+ / CAP-C+) Programmable Digital Input or Direction Input or Auxiliary Encoder or High Speed Capture (For Single-Ended Signals Leave Negative Terminal Open) I 7 PDI-9 - (DIR- / AUX ENC B- / CAP-C-) I 8 PDI-10 + Programmable Digital Input (For Single-Ended Signals Leave Negative Terminal Open) I 9 PDI-10 - I 10 SGN GND Signal Ground SGND 11 SGN GND Signal Ground SGND 12 SGN GND Signal Ground SGND 13 +5V OUT +5V Encoder Supply Output (Short Circuit Protected) O 14 PAI-4 + Differential Programmable Analog Input (12-bit Resolution) I 15 PAI-4 - I COMM - RS232/RS485 Communication Connector Pin Name Description / Notes I/O 1 SELECT RS232/485 selection. Pull to ground (CN1-5) for RS485. I 2 RS232 TX / RS485 TX- Transmit Line (RS-232 or RS-485) O 3 RS232 RX / RS485 RX- Receive Line (RS-232 or RS-485) I 4 RESERVED Reserved - 5 ISO GND Isolated Signal Ground IGND 6 RS485 TX+ Transmit Line (RS-485) O 7 RESERVED Reserved - 8 RS485 RX+ Receive Line (RS-485) I 9 RESERVED Reserved - FEEDBACK - Feedback Connector Pin Name Description / Notes I/O 1 HALL A+ Commutation Sensor Inputs I 2 HALL B+ I 3 HALL C+ I 4 MOT ENC A+ Differential Encoder A Channel Input (For Single Ended Signals Use Only The Positive Input) I 5 MOT ENC A- I 6 MOT ENC B+ Differential Encoder B Channel Input (For Single Ended Signals Use Only The Positive Input) I 7 MOT ENC B- I 8 MOT ENC I+ Differential Encoder Index Input (For Single Ended Signals Use Only The Positive Input) I 9 MOT ENC I- I 10 HALL A- Commutation Sensor Input (For Differential Signals Only) I 11 HALL B- Commutation Sensor Input (For Differential Signals Only) I 12 SGN GND Signal Ground SGND 13 +5V OUT +5V Encoder Supply Output (Short Circuit Protected) O 14 PAI-3 Programmable Analog Input (12-bit Resolution) I 15 HALL C- Commutation Sensor Input (For Differential Signals Only) I ELECTROMATE Toll Free Phone (877) SERVO98 Toll Free Fax (877) SERV099 www.electromate.com sales@electromate.com Sold & Serviced By:
- 5. DigiFlex® Performance™ Servo Drive DPRAHIE-015S400 I/O - Signal Connector Pin Name Description / Notes I/O 1 PDO-1 Isolated Programmable Digital Output O 2 OUTPUT COMMON Digital Output Common OGND 3 PDO-2 Isolated Programmable Digital Output O 4 PAI-1 + (REF+) Differential Programmable Analog Input or Reference Signal Input (16-bit Resolution) I 5 PAI-1 - (REF-) I 6 PAI-2 Programmable Analog Input (12-bit Resolution) I 7 SGN GND Signal Ground SGND 8 OUTPUT PULL-UP Digital Output Pull-Up For User Outputs I 9 PDI-5 Isolated Programmable Digital Input I 10 PDO-3 Isolated Programmable Digital Output O 11 PDI-1 Isolated Programmable Digital Input I 12 PDI-2 Isolated Programmable Digital Input I 13 PDI-3 Isolated Programmable Digital Input I 14 PDO-4 Isolated Programmable Digital Output O 15 INPUT COMMON Digital Input Common (Can Be Used To Pull-Up Digital Inputs) IGND 16 SGN GND Signal Ground SGND 17 PDI-4 (STEP) Isolated Programmable Digital Input or Step I 18 PDI-6 (DIR) Isolated Programmable Digital Input or Direction I 19 PDI-7 (CAP-A) Isolated Programmable Digital Input or High Speed Capture I 20 ENC A+ OUT Buffered Encoder Channel A Output O 21 ENC A- OUT O 22 ENC B+ OUT Buffered Encoder Channel B Output O 23 ENC B- OUT O 24 ENC I+ OUT Buffered Encoder Index Output O 25 ENC I- OUT O 26 SGN GND Signal Ground SGND POWER - Power Connector Pin Name Description / Notes I/O 1 MOTOR A Motor Phase A O 2 MOTOR B Motor Phase B O 3 MOTOR C Motor Phase C O 4 SHIELD Motor cable shield. Internally connected to protective earth ground. - 5 PE Protective Earth Ground - 6 L1 AC Supply Input (Single Phase) I 7 L2 (N) I 8 DC+ Internal DC Bus Voltage I/O 9 BR External Brake Resistor Connection. If using an external brake resistor, connect between this port and DC+. - 10 DC- Internal DC Bus Voltage I/O ELECTROMATE Toll Free Phone (877) SERVO98 Toll Free Fax (877) SERV099 www.electromate.com sales@electromate.com Sold & Serviced By:
- 6. DigiFlex® Performance™ Servo Drive DPRAHIE-015S400 HARDWARE SETTINGS Switch Functions Switch Description Setting On Off 1 Bit 0 of binary RS-485 drive address. Does not affect RS-232 settings. 1 0 2 Bit 1 of binary RS-485 drive address. Does not affect RS-232 settings. 1 0 3 Bit 2 of binary RS-485 drive address. Does not affect RS-232 settings. 1 0 4 Bit 3 of binary RS-485 drive address. Does not affect RS-232 settings. 1 0 5 Bit 4 of binary RS-485 drive address. Does not affect RS-232 settings. 1 0 6 Bit 5 of binary RS-485 drive address. Does not affect RS-232 settings. 1 0 7 Bit 0 of drive RS-485 baud rate setting. Does not affect RS-232 settings. 1 0 8 Bit 1 of drive RS-485 baud rate setting. Does not affect RS-232 settings. 1 0 Additional Details The drive can be configured to use the address and/or bit rate stored in non-volatile memory by setting the address and/or bit rate value to 0. Use the table below to map actual bit rates to a bit rate setting. Baud Rate (kbps) Value For Bit Rate Setting Load from non-volatile memory 0 9.6 1 38.4 2 115.2 3 ELECTROMATE Toll Free Phone (877) SERVO98 Toll Free Fax (877) SERV099 www.electromate.com sales@electromate.com Sold & Serviced By:
- 7. DigiFlex® Performance™ Servo Drive DPRAHIE-015S400 MECHANICAL INFORMATION +24V LOGIC - Logic Power Connector Connector Information 2-port, 5.08 mm spaced, enclosed, friction lock header Mating Connector Details Phoenix Contact: P/N 1757019 Included with Drive Yes LOGIC -1LOGIC +2 AUX ENCODER - Auxiliary Feedback Connector Connector Information 15-pin, high-density, male D-sub Mating Connector Details TYCO: Plug P/N 1658681-1; Housing P/N 5748677-1; Terminals P/N 1658686-2 (loose) or 1658686-1 (strip) Included with Drive No PDI-8 - (PWM- / AUX ENC A- / CAP-B-)5PDI-8 + (PWM+ / AUX ENC A+ / CAP-B+)4PAI-4 -15PAI-4 +14+5V OUT13SGN GND12SGN GND11SGN GND10PDI-9 + (DIR+ / AUX ENC B+ / CAP-C+)6PDI-10 -9PDI-10 +8PDI-9 - (DIR- / AUX ENC B- / CAP-C-)7 COMM - RS232/RS485 Communication Connector Connector Information 9-pin, female D-sub Mating Connector Details TYCO: Plug P/N 205204-4; Housing P/N 5748677-1; Terminals P/N 1658540-5 (loose) or 1658540-4 (strip) Included with Drive No SELECT1RS232 TX / RS485 TX-2RS232 RX / RS485 RX-3ISO GND5RS485 TX+6RS485 RX+8 ELECTROMATE Toll Free Phone (877) SERVO98 Toll Free Fax (877) SERV099 www.electromate.com sales@electromate.com Sold & Serviced By:
- 8. DigiFlex® Performance™ Servo Drive DPRAHIE-015S400 FEEDBACK - Feedback Connector Connector Information 15-pin, high-density, female D-sub Mating Connector Details TYCO: Plug P/N 748364-1; Housing P/N 5748677-1; Terminals P/N 1658670-2 (loose) or 1658670-1 (strip) Included with Drive No HALL A+1HALL B+2HALL C+3MOT ENC A+4MOT ENC A-5HALL B-11SGN GND12+5V OUT13PAI-314HALL C-15MOT ENC B+6HALL A-10MOT ENC B-7MOT ENC I+8MOT ENC I-9 I/O - Signal Connector Connector Information 26-pin, high-density, female D-sub Mating Connector Details TYCO: Plug P/N 1658671-1; Housing P/N 5748677-2; Terminals P/N 1658670-2 (loose) or 1658670-1 (strip) Included with Drive No PDO-1123456897PDO-414PDI-111PDI-212PDI-313PDO-310INPUT COMMON15PDI-4 (STEP)17PDI-6 (DIR)18SGN GND16OUTPUT COMMONPDI-5OUTPUT PULL-UPSGN GNDPAI-2PAI-1 - (REF-) PAI-1 + (REF+) PDO-2PDI-7 (CAP-A)19ENC I+ OUT24ENC B+ OUT22ENC A+ OUT20ENC A-OUT21ENC B-OUT23ENC I-OUT25SGN GND26 POWER - Power Connector Connector Information 10-port, 5.08 mm spaced, enclosed, friction lock header Mating Connector Details Phoenix Contact: P/N 1781069 Included with Drive Yes MOTOR A1MOTOR B2MOTOR C3SHIELD4PE5L16L2 (N)7DC+8BR9DC-10 ELECTROMATE Toll Free Phone (877) SERVO98 Toll Free Fax (877) SERV099 www.electromate.com sales@electromate.com Sold & Serviced By:
- 9. DigiFlex® Performance™ Servo Drive DPRAHIE-015S400 MOUNTING DIMENSIONS ELECTROMATE Toll Free Phone (877) SERVO98 Toll Free Fax (877) SERV099 www.electromate.com sales@electromate.com Sold & Serviced By:
- 10. DigiFlex® Performance™ Servo Drive DPRAHIE-015S400 PART NUMBERING INFORMATION - Drive SeriesDigiFlex PerformanceCommunicationCommand InputsRPDIHAE510S004Example: DPRS232/RS485RCANopen or RS232CEthernet Powerlink or TCP/IPPAnalog (±10V) No Step & DirectionANAnalog (±10V) Low Voltage Step & Direction (5V)ALAnalog (±10V) High Voltage Step & Direction (24V)AHNo AnalogLow Voltage Step & Direction (5V)NLNo Analog, No Step & Direction(Communication Interface Only)NNDigital I/OIsolated (24V)ITTL (5V) Non-IsolatedTMotor FeedbackIncremental Encoder and/or HallsEResolverRAbsolute Sin/Cos (Hiperface & Endat)ASin/Cos with HallsSMax DC Bus Voltage (VDC) 80080200200400400800800AC Input+24VDC User Logic Supply RequiredAAC Input Single Phase Only+24VDC User Logic Supply RequiredSDC InputBoth Logic Supply Options (Internal or User)BDC InputLogic Supply RequiredL15015160162002025025300304004060C060100C100- Code used to identify customer specialsPower and Logic SupplyPeak Current (A0 to Peak) Customer SpecialEtherCATEUniversal (Halls, Inc. Enc., Abs. Enc., 1Vp-p Sin/Cos Enc.)U60060 DigiFlex® Performance™ series of products are available in many configurations. Note that not all possible part number combinations are offered as standard drives. All models listed in the selection tables of the website are readily available, standard product offerings. ADVANCED Motion Controls also has the capability to promptly develop and deliver specified products for OEMs with volume requests. Our Applications and Engineering Departments will work closely with your design team through all stages of development in order to provide the best servo drive solution for your system. Equipped with on-site manufacturing for quick- turn customs capabilities, ADVANCED Motion Controls utilizes our years of engineering and manufacturing expertise to decrease your costs and time-to-market while increasing system quality and reliability. Feel free to contact Applications Engineering for further information and details. Examples of Customized Products Optimized Footprint Tailored Project File Private Label Software Silkscreen Branding OEM Specified Connectors Optimized Base Plate No Outer Case Increased Current Limits Increased Current Resolution Increased Voltage Range Increased Temperature Range Conformal Coating Custom Control Interface Multi-Axis Configurations Integrated System I/O Reduced Profile Size and Weight Available Accessories ADVANCED Motion Controls offers a variety of accessories designed to facilitate drive integration into a servo system. Visit www.a-m-c.com to see which accessories will assist with your application design and implementation. Shunt Regulators Drive(s) Filter Cards To Motor All specifications in this document are subject to change without written notice. Actual product may differ from pictures provided in this document. ELECTROMATE Toll Free Phone (877) SERVO98 Toll Free Fax (877) SERV099 www.electromate.com sales@electromate.com Sold & Serviced By: