Advanced motion controls dpranir 060a400
0 likes119 views
This document provides specifications for the DigiFlex® PerformanceTM Servo Drive DPRANIR-060A400. It can drive brushed and brushless motors in torque, velocity, or position mode. Key features include regenerative braking, space vector modulation for efficiency, configurable I/O, and compliance with various safety standards. It has a peak current of 60A, continuous current of 30A, and supports feedback from encoders and resolvers.
Advanced motion controls dpranir 060a400
- 1. DigiFlex® Performance™ Servo Drive DPRANIR-060A400 Description Power Range The DigiFlex® Performance™ (DP) Series digital servo drives are designed to drive brushed and brushless servomotors. These fully digital drives operate in torque, velocity, or position mode and employ Space Vector Modulation (SVM), which results in higher bus voltage utilization and reduced heat dissipation compared to traditional PWM. The drive can be configured for a variety of external command signals. Commands can also be configured using the drive’s built-in Motion Engine, an internal motion controller used with distributed motion applications. In addition to motor control, these drives feature dedicated and programmable digital and analog inputs and outputs to enhance interfacing with external controllers and devices. This DP Series drive features a single RS-232/RS-485 interface used for drive configuration and setup. Drive commissioning is accomplished using DriveWare® 7, available for download at www.a-m-c.com. All drive and motor parameters are stored in non- volatile memory. Peak Current 60 A (42.4 ARMS) Continuous Current 30 A (21.2 ARMS) Supply Voltage 100 - 240 VAC Features Four Quadrant Regenerative Operation Space Vector Modulation (SVM) Technology Fully Digital State-of-the-art Design Programmable Gain Settings Fully Configurable Current, Voltage, Velocity and Position Limits PIDF Velocity Loop PID + FF Position Loop Compact Size, High Power Density 16-bit Analog to Digital Hardware Built-in brake/shunt regulator Internal brake/shunt resistor On-the-Fly Mode Switching On-the-Fly Gain Set Switching MODES OF OPERATION Current Position Velocity COMMAND SOURCE PWM and Direction Encoder Following Over the Network ±10 V Analog Indexing Jogging FEEDBACK SUPPORTED Resolver ±10 VDC Position Auxiliary Incremental Encoder Tachometer (±10 VDC) INPUTS/OUTPUTS 3 High Speed Captures 4 Programmable Analog Inputs (16-bit/12-bit Resolution) 1 Programmable Analog Output (10-bit Resolution) 3 Programmable Digital Inputs (Differential) 7 Programmable Digital Inputs (Single-Ended) 4 Programmable Digital Outputs (Single-Ended) COMPLIANCES & AGENCY APPROVALS UL cUL CE Class A (LVD) CE Class A (EMC) RoHS ELECTROMATE Toll Free Phone (877) SERVO98 Toll Free Fax (877) SERV099 www.electromate.com sales@electromate.com Sold & Serviced By:
- 2. DigiFlex® Performance™ Servo Drive DPRANIR-060A400 BLOCK DIAGRAM SELECTTX/TX– I/O InterfaceI/O Interface DriveLogicRS232/485InterfaceCONTROL MODULERX/RX– TX+ RX+ ISO GNDPAI-1,4 + (REF+) PAI-1,4 – (REF–) PDI-1,2,3,4,5,6,7INPUT COMMONPDI-8,9,10 + (PWM+ / DIR+ / AUX ENC A,B,I + / CAP-A,B,C+) PDO-1,2,3,4OUTPUT COMMON5k+5V10k+5V10k2.5k20k20k20kPAI-2,3SGN GNDPAI-2: 33kPAI-3: 500k3.75KPDI-8,9,10 – (PWM– / DIR– / AUX ENC A,B,I – / CAP-A,B,C–) OUTPUT PULL-UPPAO-110k Motor FeedbackMotor Feedback ENC A,B,I + OUTENC A,B,I – OUTREF OUT + REF OUT – SIN,COS + SIN,COS – DC+ MOTOR AMOTOR BMOTOR CEXTPOWER MODULEPower StageLogic PowerL1L2L3LOGIC+ LOGIC– Shunt Reg. FuseFuseFuseFuse10 (200W) INTDC+ DC- Information on Approvals and Compliances US and Canadian safety compliance with UL 508c, the industrial standard for power conversion electronics. UL registered under file number E140173. Note that machine components compliant with UL are considered UL registered as opposed to UL listed as would be the case for commercial products. Compliant with European CE for both the Class A EMC Directive 2004/108/EC on Electromagnetic Compatibility (specifically EN 61000-6-4:2007 and EN 61000-6-2:2005) and LVD requirements of directive 2006/95/EC (specifically EN 60204-1:2006), a low voltage directive to protect users from electrical shock. RoHS (Reduction of Hazardous Substances) is intended to prevent hazardous substances such as lead from being manufactured in electrical and electronic equipment. ELECTROMATE Toll Free Phone (877) SERVO98 Toll Free Fax (877) SERV099 www.electromate.com sales@electromate.com Sold & Serviced By:
- 3. DigiFlex® Performance™ Servo Drive DPRANIR-060A400 SPECIFICATIONS Power Specifications Description Units Value Rated Voltage VAC (VDC) 240 (339) AC Supply Voltage Range VAC 100 - 240 AC Supply Minimum VAC 90 AC Supply Maximum VAC 264 AC Input Phases1 - 3 AC Supply Frequency Hz 50 - 60 DC Supply Voltage Range2 VDC 127 - 373 DC Bus Over Voltage Limit VDC 429 DC Bus Under Voltage Limit VDC 55 Logic Supply Voltage VDC 20 - 30 (@ 850 mA) Maximum Peak Output Current3 A (Arms) 60 (42.4) Maximum Continuous Output Current A (Arms) 30 (21.2) Max. Continuous Output Power @ Rated Voltage4 W 6840 Max. Continuous Power Dissipation @ Rated Voltage W 360 Internal Bus Capacitance μF 1650 External Shunt Resistor Minimum Resistance Ω 10 Minimum Load Inductance (Line-To-Line)5 μH 600 Switching Frequency kHz 20 Maximum Output PWM Duty Cycle % 100 Internal Shunt Fuse Rating A 5 A time-delay fuse AC Line Fuse Rating A 20 A fast-acting fuses Low Voltage Supply Outputs - +5 VDC (250 mA) Control Specifications Description Units Value Communication Interfaces - RS-485/232 Command Sources - ±10 V Analog, Encoder Following, Over the Network, PWM and Direction, Indexing, Jogging Feedback Supported - ±10 VDC Position, Auxiliary Incremental Encoder, Resolver, Tachometer (±10 VDC) Commutation Methods - Sinusoidal Modes of Operation - Current, Position, Velocity Motors Supported - Closed Loop Vector, Single Phase (Brushed, Voice Coil, Inductive Load), Three Phase (Brushless) Hardware Protection - 40+ Configurable Functions, Over Current, Over Temperature (Drive & Motor), Over Voltage, Short Circuit (Phase-Phase & Phase-Ground), Under Voltage Programmable Digital Inputs/Outputs (PDIs/PDOs) - 10/4 Programmable Analog Inputs/Outputs (PAIs/PAOs) - 4/1 Primary I/O Logic Level - 24 VDC Current Loop Sample Time μs 50 Velocity Loop Sample Time μs 100 Position Loop Sample Time μs 100 Resolver Reference/Excitation Signal Vrms 4 Vrms @ 5 kHz Expected Resolver Transformation Ratio Vrms 0.5 Feedback Resolution / Emulated Encoder Resolution6 bit High Resolution Setting: 14, Low Resolution Setting: 12 Maximum Motor Speed Per Feedback Resolution RPM High Resolution Setting: 5000, Low Resolution Setting: 20000 Internal Shunt Regulator - Yes Internal Shunt Resistor - Yes Mechanical Specifications Description Units Value Agency Approvals - CE Class A (EMC), CE Class A (LVD), cUL, RoHS, UL Size (H x W x D) mm (in) 234.7 x 161.8 x 151.3 (9.2 x 6.4 x 6) Weight g (oz) 4493 (158.5) Heatsink (Base) Temperature Range7 °C (°F) 0 - 75 (32 - 167) Storage Temperature Range °C (°F) -40 - 85 (-40 - 185) Form Factor - Panel Mount Cooling System - Natural Convection IP Rating - IP10 +24V LOGIC Connector - 2-port, 5.08 mm spaced, enclosed, friction lock header with threaded flange AUX ENCODER Connector - 15-pin, high-density, male D-sub COMM Connector - 9-pin, female D-sub DC BUS / BRAKE RESISTOR Connector - 5-contact, 13 mm spaced, dual-barrier terminal block FEEDBACK Connector - 15-pin, high-density, female D-sub I/O Connector - 26-pin, high-density, female D-sub MOTOR POWER / DC BUS Connector - 5-contact, 13 mm spaced, dual-barrier terminal block POWER Connector - 5-contact, 13 mm spaced, dual-barrier terminal block Notes 1. Can operate on single-phase VAC if peak/cont. current ratings are reduced by at least 30%. 2. Large inrush current may occur upon initial DC supply connection to DC Bus. 3. Capable of supplying drive rated peak current for 2 seconds with 10 second foldback to continuous value. Longer times are possible with lower current limits. 4. P = (DC Rated Voltage) * (Cont. RMS Current) * 0.95. 5. Lower inductance is acceptable for bus voltages well below maximum. Use external inductance to meet requirements. 6. Higher and lower resolution options are available. Contact Applications Engineering for more information. 7. Additional cooling and/or heatsink may be required to achieve rated performance. ELECTROMATE Toll Free Phone (877) SERVO98 Toll Free Fax (877) SERV099 www.electromate.com sales@electromate.com Sold & Serviced By:
- 4. DigiFlex® Performance™ Servo Drive DPRANIR-060A400 PIN FUNCTIONS +24V LOGIC - Logic Power Connector Pin Name Description / Notes I/O 1 LOGIC GND Logic Supply Ground GND 2 LOGIC PWR Logic Supply Input I AUX ENCODER - Auxiliary Feedback Connector Pin Name Description / Notes I/O 1 RESERVED Reserved - 2 RESERVED Reserved - 3 RESERVED Reserved - 4 PDI-8 + (PWM+ / AUX ENC A+ / CAP-B+) Programmable Digital Input or PWM or Auxiliary Encoder or High Speed Capture (For Single-Ended Signals Leave Negative Terminal Open) I 5 PDI-8 - (PWM- / AUX ENC A- / CAP-B-) I 6 PDI-9 + (DIR+ / AUX ENC B+ / CAP-C+) Programmable Digital Input or Direction Input or Auxiliary Encoder or High Speed Capture (For Single-Ended Signals Leave Negative Terminal Open) I 7 PDI-9 - (DIR- / AUX ENC B- / CAP-C-) I 8 PDI-10 + (AUX ENC I+ / CAP-A+) Programmable Digital Input or Auxiliary Encoder or High Speed Capture (For Single-Ended Signals Leave Negative Terminal Open) I 9 PDI-10 - (AUX ENC I- / CAP-A-) I 10 SGN GND Signal Ground SGND 11 SGN GND Signal Ground SGND 12 SGN GND Signal Ground SGND 13 +5V OUT +5V Encoder Supply Output (Short Circuit Protected) O 14 PAI-4 + Differential Programmable Analog Input (12-bit Resolution) I 15 PAI-4 - I COMM - RS232/RS485 Communication Connector Pin Name Description / Notes I/O 1 SELECT RS232/485 selection. Pull to ground (CN1-5) for RS485. I 2 RS232 TX / RS485 TX- Transmit Line (RS-232 or RS-485) O 3 RS232 RX / RS485 RX- Receive Line (RS-232 or RS-485) I 4 RESERVED Reserved - 5 ISO GND Isolated Signal Ground IGND 6 RS485 TX+ Transmit Line (RS-485) O 7 RESERVED Reserved - 8 RS485 RX+ Receive Line (RS-485) I 9 RESERVED Reserved - DC BUS / BRAKE RESISTOR - Power Connector Pin Name Description / Notes I/O 1 HIGH VOLTAGE DC Bus Output O 2 POWER GND PGND 3 EXT External Brake Resistor Connection. - 4 DC+ Brake Resistor DC+. Connection for brake resistor. O 5 INT Internal Brake Resistor. Jumper to Brake Resistor DC+ to activate. - FEEDBACK - Feedback Connector Pin Name Description / Notes I/O 1 RESERVED Reserved - 2 RESERVED Reserved - 3 RESERVED Reserved - 4 REF OUT + Resolver Reference/Excitation Output O 5 REF OUT - O 6 SIN+ Resolver Sine Input I 7 SIN- I 8 COS+ Resolver Cosine Input I 9 COS- I 10 RESERVED Reserved - 11 RESERVED Reserved - 12 SGN GND Signal Ground SGND 13 +5V OUT +5V Encoder Supply Output (Short Circuit Protected) O 14 PAI-3 Programmable Analog Input (12-bit Resolution) I 15 RESERVED Reserved - ELECTROMATE Toll Free Phone (877) SERVO98 Toll Free Fax (877) SERV099 www.electromate.com sales@electromate.com Sold & Serviced By:
- 5. DigiFlex® Performance™ Servo Drive DPRANIR-060A400 I/O - Signal Connector Pin Name Description / Notes I/O 1 PDO-1 Isolated Programmable Digital Output O 2 OUTPUT COMMON Digital Output Common OGND 3 PDO-2 Isolated Programmable Digital Output O 4 PAI-1 + (REF+) Differential Programmable Analog Input or Reference Signal Input (16-bit Resolution) I 5 PAI-1 - (REF-) I 6 PAI-2 Programmable Analog Input (12-bit Resolution) I 7 PAO-1 Programmable Analog Output (10-bit Resolution) O 8 OUTPUT PULL-UP Digital Output Pull-Up For User Outputs I 9 PDI-5 Isolated Programmable Digital Input I 10 PDO-3 Isolated Programmable Digital Output O 11 PDI-1 Isolated Programmable Digital Input I 12 PDI-2 Isolated Programmable Digital Input I 13 PDI-3 Isolated Programmable Digital Input I 14 PDO-4 Isolated Programmable Digital Output O 15 INPUT COMMON Digital Input Common (Can Be Used To Pull-Up Digital Inputs) IGND 16 SGN GND Signal Ground SGND 17 PDI-4 Isolated Programmable Digital Input I 18 PDI-6 Isolated Programmable Digital Input I 19 PDI-7 Isolated Programmable Digital Input I 20 ENC A+ OUT Emulated Encoder Channel A Output O 21 ENC A- OUT O 22 ENC B+ OUT Emulated Encoder Channel B Output O 23 ENC B- OUT O 24 ENC I+ OUT Emulated Encoder Index Output O 25 ENC I- OUT O 26 SGN GND Signal Ground SGND MOTOR POWER / DC BUS - Power Connector Pin Name Description / Notes I/O 1 MOTOR A Motor Phase A O 2 MOTOR B Motor Phase B O 3 MOTOR C Motor Phase C O 4 POWER GND Power Ground (Isolated From Signal Ground) PGND 5 HIGH VOLTAGE DC Power Input I POWER - Power Connector Pin Name Description / Notes I/O 1 L1 AC Supply Input (Three Phase) I 2 L2 I 3 L3 I 4 PE Protective Earth Ground - 5 RESERVED Reserved - ELECTROMATE Toll Free Phone (877) SERVO98 Toll Free Fax (877) SERV099 www.electromate.com sales@electromate.com Sold & Serviced By:
- 6. DigiFlex® Performance™ Servo Drive DPRANIR-060A400 HARDWARE SETTINGS Switch Functions Switch Description Setting On Off 1 Bit 0 of binary RS-485 drive address. Does not affect RS-232 settings. 1 0 2 Bit 1 of binary RS-485 drive address. Does not affect RS-232 settings. 1 0 3 Bit 2 of binary RS-485 drive address. Does not affect RS-232 settings. 1 0 4 Bit 3 of binary RS-485 drive address. Does not affect RS-232 settings. 1 0 5 Bit 4 of binary RS-485 drive address. Does not affect RS-232 settings. 1 0 6 Bit 5 of binary RS-485 drive address. Does not affect RS-232 settings. 1 0 7 Bit 0 of drive RS-485 baud rate setting. Does not affect RS-232 settings. 1 0 8 Bit 1 of drive RS-485 baud rate setting. Does not affect RS-232 settings. 1 0 Additional Details The drive can be configured to use the address and/or bit rate stored in non-volatile memory by setting the address and/or bit rate value to 0. Use the table below to map actual bit rates to a bit rate setting. Baud Rate (kbps) Value For Bit Rate Setting Load from non-volatile memory 0 9.6 1 38.4 2 115.2 3 ELECTROMATE Toll Free Phone (877) SERVO98 Toll Free Fax (877) SERV099 www.electromate.com sales@electromate.com Sold & Serviced By:
- 7. DigiFlex® Performance™ Servo Drive DPRANIR-060A400 MECHANICAL INFORMATION +24V LOGIC - Logic Power Connector Connector Information 2-port, 5.08 mm spaced, enclosed, friction lock header with threaded flange Mating Connector Details Phoenix Contact: P/N 1777808 Included with Drive Yes LOGIC GND1LOGIC PWR2 AUX ENCODER - Auxiliary Feedback Connector Connector Information 15-pin, high-density, male D-sub Mating Connector Details TYCO: Plug P/N 1658681-1; Housing P/N 5748677-1; Terminals P/N 1658686-2 (loose) or 1658686-1 (strip) Included with Drive No PDI-8 - (PWM- / AUX ENC A- / CAP-B-)5PDI-8 + (PWM+ / AUX ENC A+ / CAP-B+)4PAI-4 -15PAI-4 +14+5V OUT13SGN GND12SGN GND11SGN GND10PDI-9 + (DIR+ / AUX ENC B+ / CAP-C+)6PDI-10 - (AUX ENC I- / CAP-A-)9PDI-10 + (AUX ENC I+ / CAP-A+)8PDI-9 - (DIR- / AUX ENC B- / CAP-C-)7 COMM - RS232/RS485 Communication Connector Connector Information 9-pin, female D-sub Mating Connector Details TYCO: Plug P/N 205204-4; Housing P/N 5748677-1; Terminals P/N 1658540-5 (loose) or 1658540-4 (strip) Included with Drive No SELECT1RS232 TX / RS485 TX-2RS232 RX / RS485 RX-3ISO GND5RS485 TX+6RS485 RX+8 ELECTROMATE Toll Free Phone (877) SERVO98 Toll Free Fax (877) SERV099 www.electromate.com sales@electromate.com Sold & Serviced By:
- 8. DigiFlex® Performance™ Servo Drive DPRANIR-060A400 DC BUS / BRAKE RESISTOR - Power Connector Connector Information 5-contact, 13 mm spaced, dual-barrier terminal block Mating Connector Details Not applicable Included with Drive Not applicable HIGH VOLTAGE1POWER GND2EXT3DC+4INT5 FEEDBACK - Feedback Connector Connector Information 15-pin, high-density, female D-sub Mating Connector Details TYCO: Plug P/N 748364-1; Housing P/N 5748677-1; Terminals P/N 1658670-2 (loose) or 1658670-1 (strip) Included with Drive No REF OUT +4REF OUT -5SGN GND12+5V OUT13PAI-314SIN+6SIN-7COS+8COS-9 I/O - Signal Connector Connector Information 26-pin, high-density, female D-sub Mating Connector Details TYCO: Plug P/N 1658671-1; Housing P/N 5748677-2; Terminals P/N 1658670-2 (loose) or 1658670-1 (strip) Included with Drive No PDO-1123456897PDO-414PDI-111PDI-212PDI-313PDO-310INPUT COMMON15PDI-417PDI-618SGN GND16OUTPUT COMMONPDI-5OUTPUT PULL-UPPAO-1PAI-2PAI-1 - (REF-) PAI-1 + (REF+) PDO-2PDI-719ENC I+ OUT24ENC B+ OUT22ENC A+ OUT20ENC A-OUT21ENC B-OUT23ENC I-OUT25SGN GND26 ELECTROMATE Toll Free Phone (877) SERVO98 Toll Free Fax (877) SERV099 www.electromate.com sales@electromate.com Sold & Serviced By:
- 9. DigiFlex® Performance™ Servo Drive DPRANIR-060A400 MOTOR POWER / DC BUS - Power Connector Connector Information 5-contact, 13 mm spaced, dual-barrier terminal block Mating Connector Details Not applicable Included with Drive Not applicable MOTOR A1MOTOR B2MOTOR C3POWER GND4HIGH VOLTAGE5 POWER - Power Connector Connector Information 5-contact, 13 mm spaced, dual-barrier terminal block Mating Connector Details Not applicable Included with Drive Not applicable L11L22L33PE4 ELECTROMATE Toll Free Phone (877) SERVO98 Toll Free Fax (877) SERV099 www.electromate.com sales@electromate.com Sold & Serviced By:
- 10. DigiFlex® Performance™ Servo Drive DPRANIR-060A400 MOUNTING DIMENSIONS ELECTROMATE Toll Free Phone (877) SERVO98 Toll Free Fax (877) SERV099 www.electromate.com sales@electromate.com Sold & Serviced By:
- 11. DigiFlex® Performance™ Servo Drive DPRANIR-060A400 PART NUMBERING INFORMATION - Drive SeriesDigiFlex PerformanceCommunicationCommand InputsRPDINAE510A004Example: DPRS232/RS485RCANopen or RS232CSynqNetQAnalog (±10V) No Step & DirectionANAnalog (±10V) Low Voltage Step & Direction (5V)ALAnalog (±10V) High Voltage Step & Direction (24V)AHNo AnalogLow Voltage Step & Direction (5V)NLNo Analog, No Step & Direction(Communication Interface Only)NNDigital I/OIsolated (24V)ITTL (5V) Non-IsolatedTMotor FeedbackIncremental Encoder and/or HallsEResolverRAbsolute Sin/Cos (Hiperface & Endat)ASin/Cos with HallsSMax DC Bus Voltage (VDC) 80080200200400400800800AC Input+24VDC User Logic Supply RequiredAAC Input Single Phase Only+24VDC User Logic Supply RequiredSDC InputBoth Logic Supply Options (Internal or User)BDC InputLogic Supply RequiredL15015160162002025025300304004060060100100- Code used to identify customer specialsPower and Logic SupplyPeak Current (A0 to Peak) Customer SpecialEtherCATEUniversal (Halls, Inc. Enc., Abs. Enc., 1Vp-p Sin/Cos Enc.)U DigiFlex® Performance™ series of products are available in many configurations. Note that not all possible part number combinations are offered as standard drives. All models listed in the selection tables of the website are readily available, standard product offerings. ADVANCED Motion Controls also has the capability to promptly develop and deliver specified products for OEMs with volume requests. Our Applications and Engineering Departments will work closely with your design team through all stages of development in order to provide the best servo drive solution for your system. Equipped with on-site manufacturing for quick- turn customs capabilities, ADVANCED Motion Controls utilizes our years of engineering and manufacturing expertise to decrease your costs and time-to-market while increasing system quality and reliability. Feel free to contact Applications Engineering for further information and details. Examples of Customized Products Optimized Footprint Tailored Project File Private Label Software Silkscreen Branding OEM Specified Connectors Optimized Base Plate No Outer Case Increased Current Limits Increased Current Resolution Increased Voltage Range Increased Temperature Range Conformal Coating Custom Control Interface Multi-Axis Configurations Integrated System I/O Reduced Profile Size and Weight Available Accessories ADVANCED Motion Controls offers a variety of accessories designed to facilitate drive integration into a servo system. Visit www.a-m-c.com to see which accessories will assist with your application design and implementation. Drive(s) Filter Cards To Motor All specifications in this document are subject to change without written notice. Actual product may differ from pictures provided in this document. ELECTROMATE Toll Free Phone (877) SERVO98 Toll Free Fax (877) SERV099 www.electromate.com sales@electromate.com Sold & Serviced By: