Arduino based Dual Axis Smart Solar Tracker

International Journal of Advanced Engineering, Management and Science (IJAEMS) [Vol-3, Issue-5, May- 2017]
https://dx.doi.org/10.24001/ijaems.3.5.20 ISSN: 2454-1311
www.ijaems.com Page | 532
Arduino based Dual Axis Smart Solar Tracker
Jyoti Mishra, Ritula Thakur, Alok Deep
Department of Electrical Engineering, NITTTR, Chandigarh, India
Abstract— Solar energy is rapidly advancing as an
important means of renewable energy resource. It is
radiant light and heat from the Sun that is harnessed
using a range of ever-evolving technologies such as solar
heating, photovoltaic, solar thermal energy, solar
architecture, molten salt power plants and artificial
photosynthesis. Trackers direct solar panels or modules
toward the sun. These devices change their orientation
throughout the day to follow the sun’s path to maximize
energy capture. The use of solar trackers can increase
electricity production by around a third, and some claim
by as much as 40% in some regions, compared with
modules at a fixed angle. In any solar application, the
conversion efficiency is improved when the modules are
continually adjusted to the optimum angle as the sun
traverses the sky. This paper presents the designing of a
solar tracking system which is based on Arduino UNO
and which provides movement of solar panel in the
direction of maximum sun light incident. As a result of
which we get more efficient system which is compact, low
cost as well as easy to use.
Keywords— Arduino UNO, Bluetooth module, Solar
Panel, Servo Motor.
I. INTRODUCTION
Sun is an abundant source of energy and this solar energy
can be harnesses successfully using solar photovoltaic
cells and photovoltaic effect to convert energy into
electrical energy. But the conversion efficiency of a
normal PV cell is low. One of the main reason for this is
that the output of PV cell is dependent directly on the
light intensity and with the position of sun in the sky
changing continuously from time to time, the absorption
efficiency of an immobile solar panel would be
significantly less at certain time day and year, for the
solar photovoltaic cells are maximum productive when
they are perpendicular to the sun and less productive
otherwise. So to maximize the energy generation and
improve the efficiency solar trackers are required.
The solar tracker also provided lucrative solution for third
world countries to integrate it into their solar system with
a comparatively low cost through software based solution.
The study revealed that use of stepper motor enables
accurate tracking of sun and LDR resistors used to
determine the solar light intensity [1]. Researchers
concluded that embedding the tracking system with solar
panel can response accurate and applicable to meet the
power demands at different operational conditions.
A solar tracking system designed with microcontroller
and LDR’s that actively track the sun and change its
position accordingly to maximize the energy output. The
LDR incorporated on solar panel helps to detect sunlight
which in turn moves the panel accordingly [2] .The solar
tracker described a more improved way to maximize the
power consumption by solar panel from sun by just
rotating the solar panel according to sun’s position. By
comparing the results it was discovered that direct beam
of sun helps in generating energy than it is produced
when solar panel is kept fixed. The studied have shown
that efficiency of solar panels can be increased to a great
extent if the solar panels continuously rotate in the
direction of sun. Microcontroller and an arrangement of
LDR sensors can be used for the purpose of tracking the
sun [3]. But the system was less efficient because of the
low sensitivity and disturbance of light dependent
resistors. The mechanism of solar tracking was
implemented by the use of image processing software
which combines the effect of sensors and processed
image of sun and controls the solar panel accordingly. A
new mechanical structure for solar trackers which
implemented two stepper motors for free rotation on X
and Y axis [4]. The rotation was intelligently controlled
by a pre-programmed 2K microcontroller device PIC
18F4560 which provides simple programming strategy
through C language. The designed algorithm was based
on the measurement of intensity of solar radiation which
was captured by an ultra violet sensitive device known as
Pyranometer. The system had been tested and the results
show very significant impact on the mechanical design,
controlling algorithm and also the cost of the
development.
II. BLOCK DIAGRAM DESCRIPTION
The main aim of the proposed system is to develop a cost
effective instrument using an Arduino Microcontroller
based solar tracking system using Bluetooth module for
detection of voltage and getting the result in android app.
Block diagram of complete system is shown in Fig. 1
below which consists of power supply, Arduino Uno,
LDR sensor, servo motor, and solar panel.

Fig. 1: Block diagram of System
A. HC-05 Bluetooth to Serial Port Module
The HC05 Bluetooth Module can be used in a Master or
Slave configuration, making it a great solution for
wireless communication. It can be used simply for a serial
port replacement to establish connection between MCU
and GPS, PC to embedded project. The HC05 module has
6 pins Vcc, GND, Tx, Rx, Key and LED. It comes
preprogrammed as a slave, so there is no need to connect
the key pin, unless it is needed to be chnaged to master
mode. The major difference between Master and Slave
modes is that, in Slave mode the Bluetooth module cannot
initiate a connection; it can however accept incoming
connections.
Table.1: Pin Description of HC05 Bluetooth Module
PIN NO. CONFIGURATION
Pin 1 STATE: NC (No
Connection)
Pin 2 Rx: Tx of Microcontroller
Pin 3 Tx: Rx of Microcontroller
Pin 4 GND: Ground
Pin 5 VCC: +5V
Pin 6 EN: NC (No Connection)
After the connection is established the Bluetooth module
can transmit and recieve data regradless of the mode it is
running in. If we use mobile phone to connect to the
Bluetooth module, we can simply use it in the Slave
mode. . The module has a factory set pin of “1234” which
is used while pairing the module to a phone. The HC-05
module can build a connection to the other modules.
B. Over view of Arduino
Arduino is an open-source electronics prototyping
platform, mostly based on small, easy-to-use hardware
and software [5-6]. It can affect devices, like lights,
motors and other actuators by receiving input from
sensor. All the action performed by Arduino is
programmed to the microcontroller on the board via
Arduino programming language and the Arduino
development environment. Arduino projects can be stand-
alone or communicate with other software applications
running on a computer and other types of hardware.
Fig. 2: Arduino Uno Microcontroller Development
Board
The Adruino Uno board as shown in Fig. 2. The Table.1
shows the specifications of Arduino Uno microcontroller
board.
Table.2: Arduino Uno specifications
Microcontroller ATmega328
Operating Voltage 5V
Supply Voltage
(recommended)
7-12V
Maximum supply Voltage
(not recommended)
20V
Digital I/O Pins 14(of which 6 provide
PWM output)
Analog Input Pins 6
DC Current per I/O Pin 40mA
DC Current for 3.3V Pin 50mA
Flash Memory 32KB of which 0.5KB
used by boot loader
SRAM 2KB
EEPROM 1KB
Clock Speed 16MHz
III. FLOWCHART OF PROCESS
The given flow chart shows the order of steps taken in the
process for designing and working of solar tracking
system. The system is designed in order to respond to the
sunlight incident on the solar panel, according to which
the movement of solar panel is done. Working of system
is controlled by arduino microcontroller.

Fig. 3: Flow Chart of Process
From the flow chart it can be seen that initially the
position of both the motors is being set after that the
voltage of LDR is checked. After this process the
orientation of sun is being estimated, according to which
the sunlight falls on the LDR. There are four LDR used
on four sides of solar panel at which sunlight falls, out of
these two work for horizontal and two works for vertical
movement of panel. The voltages of x axis sensors are
compared as well as y axis sensors, as a result of which
the panel moves in clockwise/anticlockwise or
upward/downward direction. The direction of movement
of panel is always in the direction of maximum sun light.
So, the solar tracker provides higher efficiency.
IV. HARDWARE IMPLEMENTATION
Complete system assembly of Solar is shown in Fig. 4
and 5. The system consists of Power supply unit for
whole system, Arduino UNO board, HC05 Bluetooth
module, two servo motors, solar panel, four LDR sensors
fixed on on solar panel and voltage divider circuitry.
Fig. 4: Complete Hardware assembly
Fig. 5: Hardware Assembly with Bluetooth Module
V. RESULTS AND DISCUSSION
After designing, developing and implementing of the
smart solar tracker system for voltage measurement,
improvement of solar panel efficiency, compact and low
power system is successfully done. System is tested at
different times of a day in presence of varying orientation
of sun so that it is able to detect the incident light in
different conditions. The output is taken with the help of
panel movement according to maximum efficiency. The
developed system provides results and output in android
device through transmission from the controller and we
get real time measurement on the mobile app. The output
obtained in mobile app is shown below in Fig. 6.
Fig. 6: Real Time Values of Solar Panel Voltage in
Mobile App
The readings of solar panel were recorded with and
without tracking of system and in both the conditions
different output is obtained. The obtained readings are
given in Table 3.

Table.3: Comparison of Panel Voltage with and without
Tracking
Fig. 7: Graphical Representation of Data
VI. CONCLUSION
The aim of this project was to design a dual axis tracking
system which can sense the incident solar light on the
panel and move it in the direction of maximum solar light
incident. Further the advantages and disadvantages were
also studied. The disadvantages were the challenges that
had to be overcome. From this study the main
conclusions are:
i. Proposed system is low cost and compact as
compared to the other tracking systems in use for
same application.
ii. It is very easy to program and modify because it is
Arduino based and no external programmer is
required.
iii. The designed system is easy to use and provides
better efficiency of the panel.
iv. In the developed system real time data is retrieved
on the android device.
REFERENCES
[1] Khyati vyas, Dr. Sudhir Jain, Dr. Sunil Joshi, “ A
Review on an Automatic Solar tracking System”,
International Journal of Computer Applications,
2014.
[2] Priyanjan Sharma, Nitesh Malhotra, “Solar Tracking
System Using Microcontroller”, Proceedings of 1st
International Conference on Non Conventional
Energy, pp. 77-79, January 16-17, 2014
[3] Hanif Ali Sohag, Mahmudul Hasan, Mahmuda
Khatun, Mohiuddin Ahmad, “An accurate and
efficient solar tracking system using image
processing and LDR sensor”, 2nd International
Conference on Electrical Information and
Communication Technologies, pp. 522-527, 2015.
[4] M. Amir Abas , M. Hilmi Fadzil S, Samsudin
A.Kadir, A. Khusairy Azim, “Improved Structure of
Solar Tracker with Microcontroller based Control
“,Second International Conference on Advances in
Computing, Control, and Telecommunication
Technologies, pp. 55-59, 2010.
[5] Dipti Bawa, C.Y. Patil, “Fuzzy control based solar
tracker using Arduino Uno “International Journal of
Engineering and Innovative Technology, Vol. 2, No.
12, pp. 179-187, June 2013.
[6] Radhika Grover, Shoba Krishnan, Terry Shoup,
Maryam hanbaghi, “A Competition-Based
Approach for Undergraduate Mechatronics Education
Using the Arduino Platform”, 4th
Interdisciplinary
Engineering Design Education Conference
(IEDEC), Santa Clara, CA, pp 78-83, Mar 2014.
[7] Syed Arsalan, “Sun Tracking System with
Microcontroller 8051”, International Journal of
Scientific & Engineering Research, Vol. 4, No. 6,pp.
2998-3001, June 2013.
[8] Soumya Das , Pradip Kumar Sadhu, Nitai Pal ,
Suprotim Mukherjee, “Single Axis Automatic Solar
Tracking System Using Microcontroller”, Vol. 12,
No. 12, pp. 8028-8032, December 2014.
[9] Tarlochan Kaur, Shraiya Mahajan, Shilpa Verma,
Priyanka, Jaimala Gambhir, “Arduino Based Low
Cost Dual Axis Solar Tracker”, IEEE International
conference on Power Electronics, Intelligent control
and Energy Systems, pp. 1-5, 2016.
[10]Mukul Goyal, Manohar H, Ankit Raj, Kundan
Kumar, “Smart Solar Tracking System”,
International Journal of Engineering Research &
Technology, Vol. 4, No. 2, pp. 367-369, February-
2015.
TIME SOLAR PANEL VOLTAGE
WITHOUT
TRACKING
WITH
TRACKING
08:00 am 3.62 V 5.78 V
10:00 am 5.10 V 7.08 V
12:00 pm 7.26 V 8.98 V
01:00 pm 8.42 V 9.62 V
02:00 pm 8.15 V 9.58 V
04:00 pm 5.42 V 8.23 V
06:00 pm 3.24 V 6.27 V
08:00 pm 0.12 V 0.38 V

Arduino based Dual Axis Smart Solar Tracker

More Related Content

What's hot (20)

Similar to Arduino based Dual Axis Smart Solar Tracker (20)

Recently uploaded (20)

Arduino based Dual Axis Smart Solar Tracker