ARUDINO UNO and RasberryPi with Python

Internet of Things
IoT Physical Devices and End points
and RaspberryPi

Internet of Things
IoT Physical Devices and Endpoints
Internet of Things(Elective 2) Prepared by Dr. MK Jayanthi Kannan

2
Course Specification
By
Dr. M.K. Jayanthi Kannan, M.E.,MS.,MBA., M.Phil., Ph.D.,
Professor and HOD ISE,
Faculty of Engineering & Technology,
JAIN Deemed To-Be University,
Bengaluru.
Staff Room: 324- 8.
Office Hours : 8.30 AM -4 PM
Department of Computer Science and
Engineering,
FET Block,
Internet of Things ( Elective 2) by Dr.M.K.Jayanthi Kannan

Module 4 : Arduino UNO, RaspberryPi with Python
IoT Physical Devices and Endpoints
Arduino UNO: Introduction to Arduino,
• Arduino UNO, Installing the Software,
• Fundamentals of Arduino Programming.
• IoT Physical Devices and Endpoints.
RaspberryPi: Introduction to RaspberryPi,
• About the RaspberryPi Board: Hardware Layout,
• Operating Systems on RaspberryPi, Configuring.

Module – 4
IoT Physical Devices and End Point-Aurdino UNO
1
Arduino:
 Arduino is an open-source electronics platform based on easy-
to-use hardware and software.
 Arduino boards are able to read inputs - light on a sensor, a
finger on a button, or a Twitter message - and turn it into an
output - activating a motor, turning on an LED, publishing
something online.

IoT Physical Devices and End Point-Aurdino Uno
1
Arduino:
 Arduino is an open-source electronics platform based on easy-
to-use hardware and software.
 Arduino boards are able to read inputs - light on a sensor, a
finger on a button, or a Twitter message - and turn it into an
output - activating a motor, turning on an LED, publishing
something online.

Module – 4 IoT Physical Devices and End Point-
Aurdino Uno
7
Arduino UNO:
 Arduino Uno is a microcontroller board based on the ATmega328P.
 It has 14 digital input/output pins (of which 6 can be used as PWM outputs), 6
analog inputs, a 16 MHz quartz crystal, a USB connection, a power jack, an ICSP
header and a reset button.
 "Uno" means one in Italian and was chosen to mark the release of Arduino Software
(IDE) 1.0. The Uno board and version 1.0 of Arduino Software (IDE) were the
reference versions of Arduino, now evolved to newer releases.

Module – IoT Physical Devices and End Point-
Aurdino Uno
8

1. Reset Button – This will restart any code that is loaded tothe
Arduino board
2. AREF – Stands for “Analog Reference” and is used to set an
external reference voltage
3. Ground Pin – There are a few ground pins on the Arduinoand
they all work the same
analog output
4.Digital Input/Output – Pins 0-13 can be used for digital input or 12. 3.3V Pin – This pin supplies 3.3 volts of power to your projects
output
13. 5V Pin – This pin supplies 5 volts of power to your projects
5. PWM – The pins marked with the (~) symbol can simulate
6. USB Connection – Used for powering up your Arduino and
uploading sketches
7. TX/RX – Transmit and receive data indicationLEDs
8. ATmega Microcontroller – This is the brains and is where the
programs are stored
9. Power LED Indicator – This LED lights up anytime the board is
plugged in a power source
10. Voltage Regulator – This controls the amount of voltage going
into the Arduino board
11. DC Power Barrel Jack – This is used for poweringyour
Arduino with a power supply
14. Ground Pins – There are a few ground pins on theArduino
and they all work the same
15. Analog Pins – These pins can read the signal from an analog
sensor and convert it to digital
9
Module – 6 IoT Physical Devices and End Point-
Aurdino Uno

Module –4 IoT Physical Devices and End Point-Aurdino
Uno
Fundamentals of Arduino Programming:
Two required functions / methods / routines:
void setup()
{
// runs once
}
void loop()
{
// repeats
}
10

digitalWrite()
analogWrite()
digitalRead()
if() statements/ Boolean
analogRead()
Serialcommunication
BIG
6
CONCEPTS

Comments, Comments, Comments
Comments
// this is for single line comments
// it’s good to put at the top and before anything ‘tricky’
/* this is for multi-line comments
Like this…
And this….
*/

Three commands to know…
pinMode(pin, INPUT/OUTPUT);
ex: pinMode(13, OUTPUT);
digitalWrite(pin, HIGH/LOW);
ex: digitalWrite(13, HIGH);
delay(time_ms);
ex: delay(2500); // delay of 2.5 sec.
// NOTE: -> commands are CASE-sensitive

Arduino Code Basics
Arduino programs run on two basic sections:
void setup() {
//setup motors, sensors etc
}
void loop() {
// get information from sensors
// send commands to motors
}

SETUP
16 16
The setup section is used for assigning input and outputs
(Examples: motors, LED’s,sensors etc) to ports on theArduino
It also specifies whether the device is OUTPUT or INPUT
To do this we use the command “pinMode”

SETUP
void setup() {
pinMode(9, OUTPUT);
}
port #
Input or Output

void loop() {
digitalWrite(9, HIGH);
delay(1000);
digitalWrite(9, LOW);
delay(1000);
}
L
OOP
Port # from setup
Turn the LED on
or off
Wait for 1 second
or 1000 milliseconds
18

int val = 5;
DECLARING A VARIABLE
Type
assignment
“becomes”
variable name
value
19

USING VARIABLES
int delayTime = 2000;
digitalWrite(greenLED, HIGH);
delay(delayTime);
}
int greenLED = 9;
void setup() {
Declare delayTime
pinMode(greenLED, OUTPUT)V;ariable
}
void loop() {
Use delayTime
digitalWrite(greenLED, LOVWa)ri;able
delay(delayTime);
20

Using Variables
int delayTime = 2000;
int greenLED = 9;
}
void setup() {
pinMode(greenLED, OUTPUT);
}
void loop() {
digitalWrite(greenLED, HIGH);
delay(delayTime);
digitalWrite(greenLED, LOW);
delayTime = delayTime - 100;
delay(delayTime);
subtract 100 from
21
delayTime to gradually
increase LED’s blinking
speed

Conditions
To make decisions in Arduino code we
use an ‘if’ statement
‘If’ statements are based on a TRUE or
FALSE question

23
VALUE COMPARISONS
GREATER THAN
a > b
LESS
a < b
EQUAL
a == b
GREATER THAN OR EQUAL
a >= b
LESS THAN OR EQUAL
a <= b
NOT EQUAL
a != b

IF Condition
if(true)
{
“perform some action”
}

25
int counter = 0;
void setup() {
Serial.begin(9600);
}
void loop() {
if(counter < 10)
{
Serial.println(counter);
}
counter = counter + 1;
}
IF Example

Input & Output
Transferring data from the computer to an Arduino
is done using Serial Transmission
To setup Serial communication we use the following
26
void setup() {
Serial.begin(9600);
}
26

Writing to the Console
void setup() {
Serial.begin(9600);
Serial.println(“Hello World!”);
}
void loop() {}
27

IF - ELSE
Condition
if( “answer is true”)
{
}
else
{
“perform some other action”
}

29
int counter = 0;
void setup() {
Serial.begin(9600);
}
void loop() {
if(counter < 10)
{
Serial.println(“less than 10”);
}
else
{
Serial.println(“greater than or equal to 10”);
Serial.end();
}
counter = counter + 1;}
IF - ELSE Example

IF - ELSE IF
Condition
if( “answer is true”)
{
}
else if( “answer is true”)
{
“perform some other action”
}

31
int counter = 0;
void setup() {
Serial.begin(9600);
}
void loop() {
if(counter < 10)
{
Serial.println(“less than 10”);
}
else if (counter == 10)
{
Serial.println(“equal to 10”);
}
else
{
Serial.println(“greater than 10”);
Serial.end();
}
counter = counter + 1;
}
IF - ELSE Example

BOOLEAN OPERATORS - AND
32 32
If we want all of the conditions to be true we need to use ‘AND’ logic (AND gate)
We use the symbols &&
• Example
if ( val > 10 && val < 20)

BOOLEAN OPERATORS - OR
33 32
If we want either of the conditions to be true we need to use ‘OR’ logic (OR gate)
We use the symbols ||
• Example
if ( val < 10 || val > 20)

34
BOOLEAN VARIABLES
boolean done = true;
boolean done = false;
void setup() {
Serial.begin(9600);}
void loop() {
if(!done) {
Serial.println(“HELLOWORLD”);
done = true; }
}

Important functions
• Serial.println(value);
– Prints the value to the Serial Monitor on your computer
• pinMode(pin, mode);
– Configures a digital pin to read (input) or write (output) a digital value
• digitalRead(pin);
– Reads a digital value (HIGH or LOW) on a pin set for input
• digitalWrite(pin, value);
– Writes the digital value (HIGH or LOW) to a pin set for output

• Essential Programming Concepts
– Delay
– Infinite Loop
• General Input/Output
– Polling or Busy/Wait I/O
– Interrupt Processing
• Timers and Internal Inteerrupts
• High-Level Language Extensions
• Code Transformations for Embedded Computing
– Loop Unrolling
– Loop Merging
– Loop Peeling
– Loop Tiling
OUTLINE

• Delays are essential in embedded systems, unlike high-
performance systems where we want the program to
execute as fast as possible
• Delays are used to synchronize events, or read inputs
with a specific sampling freqency (more on Bus/Wait I/O)
DELAY (1/3)

• Okay, so how do we build a delay function?
• Our reference is the system clock frequency
• We use a register or a timer to measure ticks
• Each tick is 1/frequency
• Example: Assuming a 16-bit processor, an increment
and a jump instruction is 1-cycle each and a 10 MHz
system clock, build a 1-sec delay:
• T = 1/10 MHz = 100 ns
• 1 s/100 ns = 10,000,000
int i=5000000; //2 ticks per iteration
BACK: i--;
if (i!=0) goto BACK;
DELAY (3/3)

• Embedded Systems are mostly single-functioned
• Their core application never terminates
• Infinite loops are not forbidden as long as they are done
correctly
Infinite Loop (1/2)

void main()
{
light enum {RED, ORANGE, GREEN};
loop: light = RED; //no exit from loop!
delay(20000); //20-sec red
light = ORANGE;
//2-sed orange
delay(2000);
light = GREEN;
delay(20000);
goto loop;
//20-sec green
//just repeat sequence
}
Infinite Loop (2/2)

ARUDINO UNO and RasberryPi with Python

ARUDINO UNO and RasberryPi with Python

More Related Content

Similar to ARUDINO UNO and RasberryPi with Python (20)

More from Jayanthi Kannan MK (9)

Recently uploaded (20)

ARUDINO UNO and RasberryPi with Python