Autel AutoLink AL329 User Manual

i
Trademarks
Autel®
, MaxiSys®
, MaxiDAS®
, MaxiScan®
, MaxiRecorder®
, MaxiTPMS®
, and
MaxiCheck®
are trademarks of Autel Intelligent Technology Corp., Ltd.,
registered in China, the United States and other countries. All other marks are
trademarks or registered trademarks of their respective holders.
Copyright Information
No part of this manual may be reproduced, stored in a retrieval system or
transmitted, in any form or by any means, electronic, mechanical, photocopying,
recording, or otherwise without the prior written permission of Autel.
Disclaimer of Warranties and Limitation of Liabilities
All information, specifications and illustrations in this manual are based on the
latest information available at the time of printing.
Autel reserves the right to make changes at any time without notice. While
information of this manual has been carefully checked for accuracy, no guarantee
is given for the completeness and accuracy of the contents, including but not
limited to the product specifications, functions, and illustrations.
Autel will not be liable for any direct, special, incidental, indirect damages or any
economic consequential damages (including lost profits).
IMPORTANT
Before operating or maintaining this unit, please read this manual carefully,
paying extra attention to the safety warnings and precautions.
For Services and Support:
http://pro.autel.com
www.autel.com
1-855-288-3587/1-855-AUTELUS (North America)
0086-755-8614 7779 (China)
support@autel.com
For details, please refer to the Service and Support section in this manual.

ii
Safety Precautions and Warnings
To prevent personal injury or damage to vehicles and/or the scan tool, read
this instruction manual first and observe the following safety precautions at a
minimum whenever working on a vehicle:
 Always perform automotive testing in a safe environment.
 Wear safety eye protection that meets ANSI standards.
 Keep clothing, hair, hands, tools, test equipment, etc. away from all
moving or hot engine parts.
 Operate the vehicle in a well-ventilated work area: Exhaust gases are
poisonous.
 Put blocks in front of the drive wheels and never leave the vehicle
unattended while running tests.
 Use extreme caution when working around the ignition coil, distributor
cap, ignition wires and spark plugs. These components create
hazardous voltages when the engine is running.
 Put the transmission in PARK (for automatic transmission) or NEUTRAL
(for manual transmission) and make sure the parking brake is engaged.
 Keep a fire extinguisher suitable for gasoline/chemical/ electrical fires
nearby.
 Don’t connect or disconnect any test equipment while the ignition is on
or the engine is running.
 Keep the scan tool dry, clean, free from oil/water or grease. Use a mild
detergent on a clean cloth to clean the outside of the scan tool, when
necessary.

iii
CONTENTS
1 USING THIS MANUAL............................................................................. 1
CONVENTIONS ........................................................................................... 1
2 USING THE SCAN TOOL ........................................................................ 3
TOOL DESCRIPTION .................................................................................... 3
SPECIFICATIONS......................................................................................... 4
ACCESSORIES INCLUDED ............................................................................. 4
NAVIGATION CHARACTERS ........................................................................... 4
KEYBOARD ................................................................................................ 5
POWER..................................................................................................... 5
SYSTEM SETUP .......................................................................................... 5
ABOUT.....................................................................................................14
VEHICLE COVERAGE ..................................................................................15
PRODUCT TROUBLESHOOTING .....................................................................15
3 OBD II DIAGNOSTICS............................................................................17
READ CODES............................................................................................18
ERASE CODES ..........................................................................................20
LIVE DATA ................................................................................................21
VIEW FREEZE FRAME DATA.........................................................................22
RETRIEVE I/M READINESS STATUS...............................................................23
VIEW VEHICLE INFORMATION .......................................................................28
EXIT THE OBD II TEST ...............................................................................29
4 READY TEST.........................................................................................30
GENERAL INFORMATION..............................................................................30
TEST TOOL APPLICATION ............................................................................30
LED AND TONE INTERPRETATION.................................................................32
5 COMPLIANCE INFORMATION...............................................................34
6 WARRANTY AND SERVICE...................................................................36
LIMITED ONE YEAR WARRANTY ...................................................................36
SERVICE AND SUPPORT ..............................................................................37

1
1 Using This Manual
This manual contains device usage instructions.
Some illustrations shown in this manual may contain modules and optional
equipment that are not included in your system. Contact your sales
representative for availability of other modules and optional tools or
accessories.
Conventions
The following conventions are used.
Bold Text
Bold text is used to highlight selectable items such as buttons and menu
options.
Example:
 Tap OK.
Notes and Important Messages
Notes
A NOTE provides helpful information such as additional explanations, tips,
and comments.
Example:
NOTE
New batteries reach full capacity after approximately 3 to 5 charging and
discharging cycles.
Important
IMPORTANT indicates a situation which, if not avoided, may result in
damage to the test equipment or vehicle.
Example:

2
IMPORTANT
Keep the cable away from heat, oil, sharp edges and moving parts. Replace
damaged cables immediately.
Hyperlink
Hyperlinks or links that take you to other related articles, procedures, and
illustrations are active in electronic documents. Blue italic text indicates a
selectable hyperlink and blue underlined text indicates a website link or an
email address link.
Illustrations
Illustrations used in this manual are samples, and the actual testing screen
may vary for each vehicle being tested. Observe the menu titles and on-
screen instructions to make correct option selection.
Procedures
An arrow icon indicates a procedure.
Example:
 To use the camera:
1. Tap the Camera button. The camera screen opens.
2. Focus the image to be captured in the view finder.
3. Tap the blue circle. The view finder now shows the captured picture
and auto-saves the taken photo.

3
2 Using the Scan Tool
Tool Description
Figure 2-1 Product View
1) LCD DISPLAY – displays menus and test results.
2) RED LED – indicates there is a problem in one or more of the
vehicle’s systems. The red LED also indicates DTCs are present. DTCs
display on the scan tool’s display. In this case, the MIL on the vehicle’s
instrument panel will light steady.
3) YELLOW LED – indicates there is a possible problem. A “Pending”
DTC is present and/or some of the vehicle’s emission monitors have not
run their diagnostic testing.
4) GREEN LED – indicates that engine systems are running normally
(The monitors on the vehicle are active and performing their diagnostic
testing is in the allowed limit, and no DTCs are present).
5) ONE-CLICK I/M READINESS KEY – quick-checks State
Emissions readiness and drive cycle verification.
6) ENTER/Exit BUTTON – confirms a selection (or an action) from a
menu. Or returns to previous menu.
7) SCROLL BUTTON – scrolls through menu items.

4
8) OBD II CONNECTOR – connects the scan tool to the vehicle’s Data
Link Connector (DLC).
9) USB PORT – connects the scan tool to the Windoes PC for upgrading.
Specifications
Table 2-1 Specifications
Item Description
Display TFT color display (220x176 dpi)
Connectivity USB mini 2.0
OBD II DB16
Operating Temp. 0℃ to 60 ℃ (32℉ to 140℉)
Storage Temp. -20℃ to 70 ℃ (-1℉ to 158℉)
External Power 8.0 to 18.0V power provided via vehicle battery
Dimensions
(LxWxH)
120.9 mm (4.76”) x 68.4 mm (2.69”) x 18.0 mm
(0.71”)
Weight 155.2 g (0.342 lb.)
Accessories Included
1) User Manual – instructions on tool operations.
2) Quick Guide – instructions on registering tool and updating software.
3) USB Cable – used to connect to Windows PC for updating the tool’s
software.
Navigation Characters
Characters used to help navigate the scan tool are:
1) # – identifies the control module number from which data is retrieved.
2) Pd – identifies a pending DTC when viewing DTCs.

5
Keyboard
No solvents such as alcohol are allowed to clean the keypad or display. Use
a mild nonabrasive detergent and a soft cotton cloth. Do not soak the keypad
as the keypad is not waterproof.
Power
The scan tool is powered via the vehicle Data Link Connector (DLC). Follow
the steps below to turn on the scan tool:
1) Find DLC on vehicle.
 A plastic DLC cover may be found for some vehicles and you need to
remove it before attaching the OBD II cable.
2) Plug the tool’s OBD II cable to the vehicle’s DLC.
System Setup
The scan tool allows you to make the following adjustments and settings:
1) Language: Selects the desired language.
2) Configure Monitors: Sets the monitors you want to test.
3) Unit of Measure: Sets the unit of measure to English or Metric.
4) Key Beep Set: Turns on/off key-press beep.
5) Status Beep Set: Turns on/off the I/M Readiness Status beep.
6) Tool Self-test: Checks if the LCD display, LED lamps and keyboard are
working normally.
7) Update Mode: Accesses the Update Mode.
 Tool operates with default settings until changed.
To Enter the Setup Menu
When the scan tool is powered on, it displays a Main Screen.

6
Figure 2-2 Main Menu
From the Main Screen: Use the SCROLL button to select Setup, and press
the ENTER/Exit button. Follow the instructions to make adjustments and
settings as described in the above setup options.
Figure 2-3 System Setup Screen
Language Setup
 English is the default language.
1) From System Setup screen, use the SCROLL button to select
Language, and press the ENTER/Exit button.
2) Use the SCROLL button to select the desired language and press the
ENTER/Exit button to save your selection and return to previous screen.
Figure 2-4 Sample Language Screen

7
Configure Monitors
From System Setup screen, use the SCROLL button to select Configure
Monitors, and press the ENTER/Exit button.
Figure 2-5 Sample Configure Monitors Screen
On this menu, configure the monitors to pass diagnosis, and restore the
default settings.
Allowed INC Monitors
From Configure Monitors screen, use the SCROLL button to select
Allowed INC Monitors, and press the ENTER/Exit button.
Emissions tests vary depending on the geographic or regional area in which
the vehicle is registered. To this, the scan tool provides a more flexible way
to meet different standards by allowing the user to select 0, 1, 2, or 3 “not
complete” monitors in test.
Reset Factory Default
From Configure Monitors screen, use the SCROLL button to select Reset
Factory Default, and press the ENTER/Exit button.
It will restore the default configuration settings in the Configure Monitors
menu, and delete any customized settings. In this case, the Allowed INC
Monitors will be set to 1.
The tool will display a message for your confirmation. Use SCROLL button
to select Yes to proceed or No to exit without change.
Unit of Measure
 Metric is the default measurement unit.
1) From System Setup screen, use the SCROLL button to select Unit of
Measure and press the ENTER/Exit button.

8
2) From Unit of Measure screen, use the SCROLL button to select the
desired unit of measurement.
Figure 2-6 Sample Unit of Measure Screen
3) Press the ENTER/Exit button to save your selection and return to
previous menu.
Key Beep Set
This function allows you to turn on/off the built-in speaker for key pressing.
 The default setting is Beep On.
1) From System Setup screen, use the SCROLL button to select Key
Beep Set and press the ENTER/Exit button.
2) From Key Beep Set menu, use the SCROLL button to select Beep ON
or Beep OFF to turn on/off the beep.
Figure 2-7 Sample Key Beep Set Screen
previous menu.
Status Beep Set
 The default setting is Beep On.
This function allows you to turn on/off the built-in speaker as an indicator
during diagnostic testing. Different audio tones correspond to different LED

9
lights. This function is invaluable when performing diagnostics alone, or
while working in bright areas where LED illumination alone is not sufficient.
1) From System Setup screen, use the SCROLL button to select Status
Beep Set and press the ENTER/Exit button.
2) From Status Beep Set menu, use the SCROLL button to select Beep
ON or Beep OFF to turn on/off the beep.
Figure 2-8 Sample Status Beep Set Screen
previous menu.
Tool Self-test
This function checks if the display, LED lamps and keyboard are working
properly.
Display Test
The Display Test function checks if the LCD display is working normally.
1) From System Setup screen, use the SCROLL button to select Tool
Self-test, and press the ENTER/Exit button.
2) Select Display Test from Tool Self-test menu and press the
ENTER/Exit button to start test.
Figure 2-9 Sample Tool Self-test Screen
3) When completed, press the ENTER/Exit button to exit.

10
Keyboard Test
The Keyboard Test function verifies if the keys are functioning properly.
1) Use the SCROLL button to select Keyboard Test from the Tool Self-
test menu, and then press the ENTER/Exit button.
2) Press any key to start test. When you press a key, the key name should
display on screen. If the key name does not display, the key is not
functioning.
Figure 2-10 Sample Keyboard Test Screen
 The OK button refers to ENTER/Exit button.
3) Double press ENTER/Exit to return to previous menu.
LED Test
The LED Test function verifies if the I/M Readiness LED indicator lamps are
functioning properly.
1) Use the SCROLL button to select LED Test from the Tool Self-test
menu, and then press the ENTER/Exit button.
2) In the LED Self-test menu, use the SCROLL button to select one or
more LED lamps to test. The LED should turn on or off according to the
selected commands.
Figure 2-11 Sample LED Self-test Screen
3) When completed, select Previous Menu and press the ENTER/Exit
button to exit.

11
Vehicle Info Show Set
 The default setting is Set On.
This function allows you to turn on/off the Vehicle Info display when entering
the test vehicle through OBDII function.
1) From System Setup screen, use the UP/DOWN scroll button to select
Vehicle Info Show Set and press the OK button.
2) From Vehicle Info Show Set menu, use the UP/DOWN scroll button to
select SHOW ON or SHOW OFF to turn on/off the Vehicle Info screen.
3) Press the OK button to save your selection and return to previous menu.
Update Mode
This function allows you to update the scan tool software through a
Windows-based computer.
To update your scan tool, you need the following items.
 AutoLink
AL329
 A Windows-based computer or laptop with USB ports
 The supplied USB cable
Register the Tool
The tool must be registered prior to updating it. Register the tool on our
website: www.autel.com. Visit the site to download software update
programs, research tools and retrieve warranty information.
NOTE
Prior to registration, please confirm your network is working properly.
1. Visit the website http://pro.autel.com.
2. If you already have an Autel account, Sign In with your account ID and
password.
3. If you are a new member to Autel, click on the Create Autel ID button
on the left side of the screen to create an ID.
4. Enter the required information in the input fields, and click the Get
Verification Code button to get a verification code for email validation.
5. The online system will automatically send a verification code to the
registered email address. Input the code in the Verification code field
and complete other required fields. Read through Autel’s Terms and

12
Conditions and click on Agree, and then click Create Autel ID at the
bottom. A product registration screen will display.
6. The device’s serial number and password is located in the About section
of the Settings application on the tool.
7. Select your product model, enter the product serial number and
password on the Product Registration screen, and click Submit to
complete the registration procedure.
Update Procedure
Autel frequently releases software updates to download.
Connect the tool with a Windows-based computer using the included USB
cable.
Follow the update procedure to update the software on the tool.
1. Download the Maxi PC Suite from www.autel.com > Support &
Updates > Firmware & Downloads > Update Client, and install to your
Windows-based computer.
2. Run the Maxi PC Suite. Wait for the Log In window to display.
Figure 2-12 Sample Log In Window
3. Connect the scan tool to your computer with the provided USB cable.
4. From System Setup screen in scan tool, use the SCROLL button to
select Update Mode, and press the ENTER/Exit button.
5. Enter your Autel ID and password and wait for the Update window to
display. If you forget your password, click the [Forget Password?] link
to our website and retrieve your password. Or click Sign up to create
an Autel ID to continue.
6. Select tool and serial number, click OK to continue.
7. In the Update window, select the appropriate files to install.

13
Figure 2-13 Sample Update Window
Generally, there are two ways to update programs:
Batch Update
1. Select the programs to update by checking the boxes next to those
items. Then click the Update All button on the bottom right of screen.
Click the Clear All button to deselect files.
2. Or, click on the Select All checkbox on the bottom left of screen and all
updatable items will be selected. Click the Update All button on the right
of the screen.
3. When the download is completed, the programs will be automatically
installed. The new version will replace the old version.
Single Update
1. Locate the desired update and click the Update button in the same line.
2. The downloaded programs will automatically install. The update will
replace the existing version of the software.
View or Delete Programs
To view the list of installed programs or to delete an installed program,
please follow these steps:
1. Click on the Installed tag and the list of installed programs will display.
2. Select the program(s) that you would delete.
 Batch delete: Check the boxes to the left of the program you want
to uninstall. Then click the Uninstall All button on the right bottom
of screen.
 Single delete: Click the Uninstall button adjacent to the program
to delete.

14
3. A window will display for confirmation of the selected software to
uninstall.
Figure 2-14 Sample Delete Window
 Click OK to delete the program(s) selected, or click Cancel to quit
the action.
 The deleted program(s) will be added to the end of the program list
on the Update page to install again if you wish.
In the search box on the top right corner of the screen, you can search the
listed. This function works for both Update Available column and Installed
column.
To Exit the Setup Menu
Use the SCROLL button to select Previous Menu from the System Setup
screen, and press the ENTER/Exit button to return to Main Screen.
About
The About function displays important tool information including serial
number and software version number.
1) From Main Screen, use the SCROLL button to select About and press
the ENTER/Exit button; wait for the About screen to display.
2) View tool information on screen.

15
Figure 2-15 Sample About Screen
Vehicle Coverage
The AutoLink
AL329 OBDII/EOBD Scanner is specially designed to work
with all OBD II compliant vehicles, including those equipped with Control
Area Network (CAN) protocol. The EPA requires all domestic, Asian and
European vehicles, 1996 and newer (including light trucks), sold in the
United States must be OBD II compliant.
A small number of 1994 and 1995 model year gasoline vehicles are OBD II
compliant. To verify if a 1994 or 1995 vehicle is OBD II compliant, check the
Vehicle Emissions Control Information (VECI) Label which is located under
the hood or by the radiator of most vehicles. If the vehicle is OBD II
compliant, the label will designate “OBD II Certified”. Additionally,
Government regulations mandate that all OBD II compliant vehicles must
have a “common” sixteen-pin Data Link Connector (DLC).
For your vehicle to be OBD II compliant it must have a 16-pin DLC (Data
Link Connector) under the dash and the Vehicle Emission Control
Information Label must state that the vehicle is OBD II compliant.
Product Troubleshooting
This section describes problems that may be encountered while using this
tool.
Vehicle Linking Error
A communication error occurs if the scan tool fails to communicate with the
vehicle’s ECU (Engine Control Unit). Perform the following steps to resolve
error:
 Verify that the ignition is ON.

16
 Ensure the scan tool’s OBD II connector is securely
connected to the vehicle’s DLC.
 Verify that the vehicle is OBD II compliant.
 Turn the ignition off and wait for about 10 seconds. Turn the ignition
back to on and continue the testing.
 Verify the control module is not defective.
Operating Error
If the scan tool freezes, then an exception occurs or the vehicle’s ECU
(Engine Control Unit) is too slow to respond to requests. You need to do the
following to reset the tool:
 Reset the scan tool.
back to on and continue the testing.
Scan Tool Doesn’t Power Up
If the scan tool won’t power up or operates incorrectly, do the following:
 Check if the scan tool’s OBD II connector is securely connected to the
vehicle’s DLC;
 Check if the DLC pins are bent or broken. Clean the DLC pins if
necessary.
 Check vehicle battery to make sure it is still good with at least 8.0 volts.
LED Lamps Not Working
If the LED lamps don’t light during I/M Readiness testing, do the following:
 Make sure the OBD II cable is connected to the DLC securely.
 Verify the ignition key is in the Key On, Engine Running (KOER) position.
 Run the LED Test in the System Setup menu. If the tool fails this test,
there is a problem with the LED lamp. Please contact Autel Tech
Support or your local tool distributor.

17
3 OBD II Diagnostics
When more than one vehicle control module is detected by the scan tool,
you will be prompted to select the module with retrievable data. The Power
train Control Module [PCM] and Transmission Control Module [TCM] are the
most commonly scanned modules.
CAUTION: Don’t connect or disconnect the scan tool while the ignition is on
or the engine running.
1) Turn the ignition off.
2) Locate the vehicle’s 16-pin Data Link Connector (DLC).
3) Plug the tool into the vehicle’s DLC.
4) Turn the ignition on. Engine can be off or running.
5) Use the SCROLL button to select OBD II/EOBD from the Main Screen
in the scan tool.
6) Press the ENTER/Exit button to wait for the Menu to display. The tool
will display OBDII protocols until it has detected the vehicle’s
communication protocol.
 If the scan tool fails to communicate with the vehicle’s ECU (Engine
Control Unit) more than three times, a “LINKING ERROR!”
message displays on the display.
 Verify the ignition is ON;
 Check if the scan tool’s OBD II cable is securely connected to the
vehicle’s DLC;
 Verify that the vehicle is OBD II compliant;
back on and repeat step 5.
 If the “LINKING ERROR” message continues to display, contact
your local distributor or customer service for assistance.
7) View a summary of system status (MIL status, DTC counts, Monitor
status) on screen. Wait a moment or press any key for Diagnostic
Menu to display.

18
Figure 3-1 Sample System Status Screen
 If more than one module is detected, you will be prompted to select
a module to test.
Figure 3-2 Sample Control Module Screen
 Use the SCROLL button to select a module and press the
ENTER/Exit button to confirm.
Read Codes
 The Read Codes function can be performed with the key on, engine off
(KOEO) or with the key on, engine running (KOER).
 Stored Codes are also known as “hard codes”, which are fault codes,
or trouble codes that have been stored in the vehicle computer memory
because the faults have reoccurred for more than a specified amount of
key-cycles. These codes will cause the control module to illuminate the
malfunction indicator light (MIL) when emission-related faults occur.
 Pending Codes are also referred to as “maturing codes” or “continuous
monitor codes”. They indicate problems that the control module has
detected during the current or last driving cycle but are not as yet
considered serious. Pending Codes will not cause a malfunction
indicator light (MIL). If the fault does not occur within a certain number
of warm-up cycles, the code clears from memory.
 Permanent Codes are DTCs that are "confirmed" and are retained in
the non-volatile memory of the vehicle’s computer until the appropriate

19
monitor for each DTC has determined that the malfunction is no longer
present and is not causing the MIL. Permanent DTCs are stored in non-
volatile memory and can not be erased by any diagnostics service or by
disconnecting power to ECU.
1) Use SCROLL button to select Read Codes from Diagnostic Menu and
press ENTER/Exit button.
Figure 3-3 Sample Diagnostic Menu
2) Use the SCROLL button to select Stored Codes or Pending Codes
from the Read Codes menu and press the ENTER/Exit button.
 If no codes are found, a message will display “No (pending) codes
are stored in the module!” Wait a moment or press any key to
return to previous screen.
NOTE
Permanent Codes function is available only for vehicles supporting the CAN
protocols.
3) View DTCs and their definitions on screen. Press ENTER/Exit button to
return to previous screen.
Figure 3-4 Sample DTC Screen
 The control module number, sequence of the DTCs, total number
of codes detected and type of codes (Generic or Manufacturer
specific, Stored or Pending codes) will be observed on the upper
right hand corner of the display.

20
4) If more than one DTC is found, use the SCROLL button to review each
code.
 If retrieved DTCs contain any manufacturer specific or enhanced
codes, the tool’s AutoVIN technology will automatically display the
definition of the code.
5) Select Previous Menu from the Read Codes screen, and press
ENTER/Exit button to return to previous menu.
Erase Codes
NOTE
1. Erasing the Diagnostic Trouble Codes may allow the scan tool to delete
not only the codes from the vehicle’s on-board computer, but also
“Freeze Frame” data and manufacturer-specific enhanced data. Further,
the I/M Readiness Monitor Status for all vehicle monitors is reset to Not
Ready or Not Complete status. Do not erase the codes before repairs
or services have been performed.
2. Even if deleted, codes will again display if the underlining fault causing
the code is not addressed.
1. This function is performed with key on, engine off (KOEO). Do not start
the engine.
1) Use the SCROLL button to select Erase Codes from Diagnostics
Menu and press the ENTER/Exit button.
2) A warning message displays for your confirmation.
Figure 3-5 Sample Erase Codes Screen
 If you do not want to proceed with erasing codes, use SCROLL
button to select NO to exit. A message of “Command Cancelled!”
displays. Wait a moment or press any key to return to Diagnostic
Menu.
3) Press the ENTER/Exit button to confirm.

21
 If the codes are cleared successfully, an “Erase Done!”
confirmation message displays.
Figure 3-6 Sample Erase Done Screen
 If the codes are not cleared, then an “Erase Failure. Turn Key on
with Engine off!” message displays.
Figure 3-7 Sample Erase Failure Screen
Live Data
The function allows viewing of live or real time PID data of vehicle’s
computer module(s).
1) To view live data, use the SCROLL button to select Live Data from
Diagnostic Menu and press the ENTER/Exit button.
2) Wait a few seconds while the scan tool validates the PID MAP.
Figure 3-8 Sample Live Data Reading Screen

22
3) To view complete set of data, use SCROLL button to select Complete
Data Set from View Data menu and press the ENTER/Exit button.
Figure 3-9 Sample View Data Screen
4) View live PIDs on the screen. Use the SCROLL button for more PIDs if
additional information is available on more than one page.
Figure 3-10 Sample Live Data Screen
 The number “x” to the right of the screen indicates the sequence of
the highlighted item.
5) Press the ENTER/Exit button to return to previous menu.
6) Select Previous Menu from the Read Codes screen, and press
ENTER/Exit button to return to previous menu.
View Freeze Frame Data
Freeze Frame Data allows the technician to view the vehicle’s operating
parameters at the moment a DTC (Diagnostic Trouble Code) is detected.
For example, the parameters may include engine speed (RPM), engine
coolant temperature (ECT), or vehicle speed sensor (VSS). This information
will aid the technician by allowing the parameters to be duplicated for
diagnostic and repair purposes.
1) To view freeze frame data, use the SCROLL button to select View
Freeze Frame from Diagnostic Menu and press the ENTER/Exit
button.

23
2) Wait while the scan tool validates the PID MAP.
3) If retrieved information displays on more than one screen, use the
SCROLL button, as necessary, until all the data have shown up.
Figure 3-11 Sample View Freeze Frame Screen
 If no freeze frame data is available, the message “No freeze frame
data stored!” displays.
4) Press ENTER/Exit button to return to previous screen.
Retrieve I/M Readiness Status
I/M Readiness function is used to check the operations of the Emission
System on OBD II compliant vehicles. It is an excellent function to use prior
to having a vehicle inspected for state emission compliance.
CAUTION: By clearing trouble codes you also clear the readiness status for
the individual emission system readiness tests. In order to reset these
monitors, the vehicle must be driven through a complete drive cycle with no
trouble codes in memory. Amount of time needed for reset vary by vehicle.
Some latest vehicle models may support two types of I/M Readiness tests:
A. Since DTCs Cleared – indicates status of monitors since the DTCs are
erased.
B. This Drive Cycle – indicates status of monitors since the beginning of
the current drive cycle.
An I/M Readiness Status result of “NO” does not necessarily indicate that
the vehicle being tested will fail the state I/M inspection. For some states,
one or more such monitors may be allowed to be “Not Ready” to pass the
emission inspection.
There are two ways to retrieve I/M readiness status.

24
Retrieve I/M Readiness Status with One-Click I/M
Readiness Key
Press the One-Click I/M Readiness Key, to retrieve I/M readiness status.
The screen will display as below. The LEDs colors and the audio tones
indicate readiness status.
Figure 3-12 Sample I/M Readiness Screen
OK – indicates that a particular monitor being checked has completed its
diagnostic testing.
INC – indicates that a particular monitor being checked has not
completed its diagnostic testing.
N/A – the monitor is not supported on the vehicle.
The green, yellow and red LEDs provide a quick way to help you determine
if a vehicle is ready for an Emission Test.
The LED and audio tone are interpreted as below:
LED Interpretation
1) GREEN LED – indicates that engine systems are “OK” and operating
normally (the number of Monitors supported by the vehicle that have
run and performed their self-diagnostic testing is in the allowed limit.
MIL is off. ).There are neither stored nor pending DTCs. The vehicle is
ready for an Emission Test, and there is a good possibility that it can be
certified.
2) YELLOW LED – with MIL off, there may be three possible conditions to
cause the yellow LED to light.
 If a “Stored” Diagnostic Trouble Code is causing the yellow LED to
light, it is still possible that the vehicle will be allowed to be tested
for emissions and certified.
 If a “Pending” Diagnostic Trouble Code is causing the yellow LED
to light, it is still possible that the vehicle will be allowed to be tested
for emissions and certified.

25
 The Yellow LED will also light if the monitors do not complete their
tests. Each state’s emissions standards differ on the number of
tested monitors needed to meet vehicle emissions compliance.
NOTE
Confer with your automotive technician about the status results of each
monitor to determine if the vehicle is ready for your state’s emissions test.
3) RED LED – indicates there is a problem with one or more of the
vehicle’s system. The test of a vehicle resulting in a lit red LED lighting
is not ready for an Emissions Test. The red LED is also an indication
that there are DTCs present. The MIL on the vehicle’s instrument panel
will light steady. The problem that is causing the red LED to light must
be repaired before an Emissions Test can be performed. It is also
suggested that the vehicle be inspected/repaired before driving the
vehicle further.
If the red LED lights, there is a definite problem present in the system(s).
In this case, you have the following options:
 Repair the vehicle yourself. If you are going to perform the repairs
yourself, proceed by reading the vehicle service manual and
following all its procedures and recommendations.
 Take the vehicle to a professional to have it serviced. The
problem(s) causing the red LED to light must be repaired before
the vehicle undergoes Emissions Testing.
Audio Tone Interpretation
The audio tone is configured according to the I/M Readiness Status.
Table 3-1 Audio Tone Interpretation
LED Light Audio Tone Beep Interval
Green Two long beeps 5 seconds
Yellow short, long, short beep 5 seconds
Red Four short beeps 5 seconds
After you have read the information, press ENTER/Exit to exit. The other
buttons are disabled to prevent misoperation.

26
Retrieve I/M Readiness Status in Typical Way
1) Use the SCROLL button to select I/M Readiness from Diagnostic
Menu and press ENTER/Exit button.
2) Wait while the scan tool validates the PID MAP.
3) If the vehicle supports both types of tests, then both types will be
displayed on the screen for selection.
Figure 3-13 Sample I/M Readiness Menu Screen
4) Use the SCROLL button to view the status of the MIL light (ON or OFF)
and the following monitors.
For spark ignition engines:
 MIS – Misfire Monitor
 FUEL – Fuel System Monitor
 CCM – Comprehensive Component Monitor
 EGR – EGR System Monitor
 O2S – O2 Sensors Monitor
 CAT – Catalyst Monitor
 EVAP – Evaporative System Monitor
 HTR – O2 Sensor Heater Monitor
 AIR – Secondary Air Monitor
 HCAT – Heated Catalyst Monitor
For compression ignition engines:
 MIS – Misfire Monitor
 FUEL – Fuel System Monitor
 CCM – Comprehensive Component Monitor
 EGR – EGR System Monitor
 HCCAT – NMHC Catalyst Monitor
 NCAT – NOx Aftertreatment Monitor

27
 BP – Boost Pressure System Monitor
 EGS – Exhaust Gas Sensor Monitor
 PM – PM Filter Monitor
Figure 3-14 Sample Since DTCs Cleared Screen
5) If the vehicle supports readiness test of This Drive Cycle, a screen of
the following displays.
Figure 3-15 Sample This Drive Cycle Screen
6) The LEDs and audio tones corresponding to different monitor status will
be activated as below.
Table 3-2 LED and Audio Tone Interpretation
Green Two long beeps 2 minutes
Yellow short, long, short beep 2 minutes
Red Four short beeps 2 minutes
7) Use the SCROLL button for more PIDs if additional information is
available on more than one page.
8) Press the ENTER/Exit button to return to Diagnostic Menu.

28
View Vehicle Information
This function enables retrieval of Vehicle Identification No. (VIN), Calibration
ID No. (CINs), Calibration Verification No. (CVNs) and In-use Performance
Tracking on 2000 and newer vehicles that support Mode 9.
1) Use SCROLL button to select Vehicle Info. from the Diagnostic Menu
and press ENTER/Exit button.
2) A message displays to remind you “Turn key on with engine off!” Wait a
moment or press any key to continue.
Figure 3-16 Sample Vehicle Info. Screen
3) Wait while the scan tool reads vehicle information.
Figure 3-17 Sample Reading Info. Screen
 If the vehicle does not support this mode, a message displays that
the mode is not supported.
4) From Vehicle Info. menu, use the SCROLL button to select an
available item to view and press the ENTER/Exit button.
Figure 3-18 Sample Vehicle Info. Selection Screen

29
5) View retrieved vehicle information on screen.
Figure 3-19 Sample Cal. Verf. Number Screen
6) Select Previous Menu from the Vehicle Info. screen, and press
ENTER/Exit button to return to the previous menu.
Exit the OBD II Test
1) To exit OBD II test, use SCROLL button to select Previous Menu from
Diagnostic Menu and press ENTER/Exit button.
2) A message displays for your confirmation. Press ENTER/Exit button to
exit.

30
4 Ready Test
This function can be used as a convenient readiness test tool by automotive
technicians to determine if the tested vehicle is ready for an emission test.
By visual and audible indication, you will learn a vehicle’s emissions
readiness.
General Information
Repairs to the emissions-control systems of a 1996 or newer vehicle cause
the vehicle’s computer (ECU) memory to be cleared. The vehicle must go
through a drive cycle to allow the ECU to perform a series of tests to ensure
that the repair was successful, and before a state mandated emission test
can be conducted. But how will you know when it is ready?
With this scan tool, you don’t have to drive around endlessly, continuously
coming back to the repair shop for retest to check if all required tests by the
ECU are completed. And you could also do a quick check of the vehicle to
determine if it is ready to receive an emission test without the hassle of
connecting your vehicle to the analyzer or having to use a complicated scan
tool.
In the following cases, this function is especially useful.
 You bought a used car and the check engine light had been cleared to
mask potential problems.
 You disconnected the battery for tune-ups and other engine repairs,
dead battery replacement, car radio installation and car alarm
installation.
 You used a scan tool to clear the DTCs.
 Your car has been sent for repairs.
Test Tool Application
This function displays which vehicle monitors have run, if they have been
completed and the results of the testing. Results display on one screen
providing an at-a-glance profile of the vehicle.
.

31
 Use the SCROLL button to select Ready Test from Main Screen, and
press the ENTER/Exit button.
Figure 4-1 Main Menu
As Post-Repair Diagnostic Tool
This function can be used (after the vehicle has done any emission-related
repairs) to confirm that the repair has been performed successfully.
After repairs, some drive cycles are required to reset the monitoring systems.
Drive cycles vary by vehicle and by monitor.
Use the following procedures to check if the repair has been done correctly:
1) Connect the scan tool to the vehicle’s DLC and erase the DTC(s) from
the vehicle’s computer memory.
2) After the erase procedure is performed, status of most monitors will be
changed. Leave the scan tool connected to the vehicle, and select
Ready Test from Main Screen.
3) Continue to drive the vehicle until the scan tool notifies you that the drive
cycle has been completed.
4) If the GREEN LED lights and the tool emits two long beeps, your vehicle
is ready and the repair work is confirmed.
5) If the RED LED lights, your vehicle is not ready and if you have
performed repairs, they have failed to correct the emissions issue.
As Pre-Check Diagnostic Tool
Prior to having a vehicle inspected for state emissions compliance, use this
function to check the readiness status.
1) While the scan tool connected to the vehicle, select Ready Test from
Main Screen. Drive the car till the scan tool notifies you safely with color

32
LEDs and audible tone if your vehicle is ready to conduct state emission
test.
2) If the GREEN LED lights and two long beeps are heard, your vehicle is
ready and it should pass emissions testing.
3) If the RED LED lights, your vehicle is not ready and must be repaired
before an emission test can be performed.
IMPORTANT
If you are driving the vehicle to perform a drive cycle ALONE, set the Status
Beep On. The beep signifies that the monitors have run and the diagnostics
testing completed. NEVER drive and operate the scan tool at the same time!
This function displays the real time data of emission-related monitoring
systems readiness status. Once the scan tool has finished other operations,
for example, clearing trouble codes, the I/M Readiness Monitor Status
program resets status of all the monitors to “INC” condition. The vehicle must
be driven through a complete drive cycle to set the monitors to Ready status.
Times for reset vary by vehicle. Please refer to your vehicle’s service manual
for drive cycle information.
NOTE
When using this function, only the ENTER/Exit button is available. The other
buttons are disabled to prevent misoperation.
LED and Tone Interpretation
Select Ready Test from the Main Screen and the screen displays as
depicted below, including applicable monitors status, MIL state, ignition type,
DTCs (stored one and pending).
Figure 4-2 Sample I/M Readiness Screen
If the scan tool is idle, the result will immediately display. If it is busy, it will
wait till the current procedure finished. After viewing the status, press
ENTER/Exit button to exit.

33
OK– indicates that a particular monitor being checked has completed its
diagnostic testing.
INC – indicates that a particular monitor being checked has not
completed its diagnostic testing.
N/A – the monitor is not supported on the vehicle.
The LED and audio tone indications are interpreted as below:
LED Interpretation
The green and red LEDs provide an easy way to check if emission-related
monitoring systems have completed their self-diagnostic testing.
1) GREEN LED – your vehicle is Ready. Indicates that engine systems
are “OK” and operating normally (the number of Monitors supported by
the vehicle that have run and performed their self-diagnostic testing is
in the allowed limit).
2) RED LED – your vehicle is Not Ready. Indicates that the number of
Monitors supported by the vehicle that have run and performed their
self-diagnostic testing is out of the allowed limit.
Audio Tone Interpretation
The audio tone can be configured according to the I/M Readiness Status.
Table 4-1 Audio Tone Interpretation
Green Two long beeps 2 minutes
Red No beep

34
5 Compliance Information
FCC COMPLIANCE
This device complies with Industry Canada’s licence-exempt RSSs.
Operation is subject to the following two conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received, including
interference that may cause undesired operation.
Cet appareil est conforme aux CNR exempts de licence d’Industrie Canada.
Son fonctionnement est soumis aux deux conditions suivantes:
1. Ce dispositif ne peut causer des interferences; et
2. Ce dispositif doit accepter toute interférence, y compris les interférences
qui peuvent causer un mauvais fonctionnement de l’appareil.
WARNING
Changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
NOTE
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation.
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
– Reorient or relocate the receiving antenna.

35
– Increase the separation between the equipment and receiver.
– Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
– Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
RF WARNING STATEMENT
The device has been evaluated to meet general RF exposure requirement.
The device can be used in portable exposure condition without restriction.
The term “IC” before the radio certification number only signifies that IC
technical specifications were met.
RoHS COMPLIANCE
This device is declared to be in compliance with the European RoHS Directive
2011/65/EU.
CE COMPLIANCE
This product is declared to conform to the essential requirements of the
following Directives and carries the CE mark accordingly:
EMC Directive 2014/30/EU
R&TTE Directive 1999/5/EC
Low Voltage Directive 2014/35/EU

36
6 Warranty and Service
Limited One Year Warranty
Autel Intelligent Technology Corp., Ltd. (the Company) warrants to the
original retail purchaser of this Autel device that should this product or any
part thereof during normal usage and under normal conditions be proven
defective in material or workmanship that results in product failure within 1
year period from the date of purchase, such defect(s) will be repaired, or
replaced (with new or rebuilt parts) with Proof of Purchase, at the Company’s
option, without charge for parts or labor directly related to the defect(s).
The Company shall not be liable for any incidental or consequential damages
arising from the use, misuse, or mounting of the device. Some states do not
allow limitation on how long an implied warranty lasts, so the above limitations
may not apply to you.
This warranty does not apply to:
1) Products subjected to abnormal use or conditions, accident, mishandling,
neglect, unauthorized alteration, misuse, improper installation or repair
or improper storage;
2) Products whose mechanical serial number or electronic serial number
has been removed, altered or defaced;
3) Damage from exposure to excessive temperatures or extreme
environmental conditions;
4) Damage resulting from connection to, or use of any accessory or other
product not approved or authorized by the Company;
5) Defects in appearance, cosmetic, decorative or structural items such as
framing and non-operative parts.
6) Products damaged from external causes such as fire, dirt, sand, battery
leakage, blown fuse, theft or improper usage of any electrical source.
IMPORTANT
All contents of the product may be deleted during the process of repair. You
should create a back-up copy of any contents of your product before
delivering the product for warranty service.

37
Service and Support
If you have any questions regarding the product, please contact one of our
offices or your local distributor.
AUTEL NORTH AMERICA
 Phone: 855-AUTEL-US (855-288-3587) Monday-Friday 9am-6pm EST
 Website: www.autel.com
 Email: ussupport@autel.com
 Address: 175 Central Avenue, Suite 200, Farmingdale, New York, USA.
11735
AUTEL EUROPE
 Phone: 0049 (0) 61032000522
 Website: www.autel.eu
 Email: sales.eu@autel.com, support.eu@autel.com
 Address: Robert-Bosch-Strasse 25, 63225, Langen, Germany
AUTEL CHINA HQ
 Phone: 0086-755-8614 7779
 Website: www.autel.com
 Email: support@autel.com
 Address: 6th-10th floor, Building B1, Zhiyuan, Xueyuan Road, Xili,
Nanshan, Shenzhen, 518055, China.
AUTEL SOUTH AMERICA
 Phone: (+507) 308-7566
 Website: www.autel.com/es
 Email: sales.latin@autel.com, latsupport@autel.com
 Address: Office 103, Building 3845, International Business Park,
Veracruz, PanamáPacífico, Panamá
AUTEL AUSTRALIA
 Phone: 03 9480 2978 / +61 476293327
 Website: www.autel.com.au
 Email: sales@autel.com.au
 Address: 155 Islington Street, Melbourne, Collingwood, VIC

Autel AutoLink AL329 User Manual

More Related Content

What's hot (20)

Similar to Autel AutoLink AL329 User Manual (20)

More from Tim Miller (20)

Recently uploaded (20)

Autel AutoLink AL329 User Manual