Autel max scan vag405 code reader obd2 eobd can bus vw audi

www.autoobdtools.com
Table of Contents
1. Safety Precautions and Warnings........................................1
2. Product Information .............................................................2
2.1 Tool Description ..........................................................2
2.2 Specifications ...............................................................3
2.3 Accessories Included...................................................3
2.4 Navigation Characters................................................3
2.5 Keyboard .....................................................................4
2.6 Power............................................................................4
2.7 Product Setup ..............................................................4
2.8 Vehicle Coverage.........................................................8
3. Operating Instructions..........................................................9
3.1 VW/AUDI Diagnostics................................................9
3.2 OBDII/EOBD Diagnostics........................................15
3.3 Oil Service..................................................................18
4. Warranty and Service .........................................................32
4.1 Limited One Year Warranty ...................................32
4.2 Service Procedures....................................................32

1. Safety Precautions and Warnings
To prevent personal injury or damage to vehicles and/or the scan
tool, read this instruction manual first and observe the following
safety precautions at a minimum whenever working on a vehicle:
Always perform automotive testing in a safe environment.
Wear safety eye protection that meets ANSI standards.
Keep clothing, hair, hands, tools, test equipment, etc, away from
all moving or hot engine parts.
Operate the vehicle in a well-ventilated work area; Exhaust gases
are poisonous.
Put blocks on drive wheels and never leave vehicle unattended
while running tests.
Use extreme caution when working around the ignition coil,
distributor cap, ignition wires and spark plugs. These components
create hazardous voltages when the engine is running.
Put transmission in PARK (for automatic transmission) or
NEUTRAL (for manual transmission) and make sure the parking
brake is engaged.
Keep a fire extinguisher suitable for gasoline/chemical/ electrical
fires nearby.
Don’t connect or disconnect any test equipment with ignition on
or engine running.
Keep the scan tool dry, clean and free from oil, water and grease.
Use a mild detergent on a clean cloth to clean the outside of the
scan tool, when necessary.

1

2. Product Information
2.1 Tool Description

6

1

4

2 3

5

① LCD DISPLAY -- Indicates test results. Backlit, 128 x 64 pixel
display with contrast adjustment.
② Y BUTTON -- Confirms a selection (or action) from a menu.
When a DTC’s definition covers more than one screen, it is used
to move down to the next screen for additional data.
③ N BUTTON -- Cancels a selection (or action) from a menu or
returns to the menu. It is also used to set up the unit when being
pressed and held for at least 3 seconds.

2

④ UP SCROLL BUTTON -- Moves up through menu and
submenu items in menu mode. When more than one DTC is
retrieved, moves up through the current screen to the previous
screens for additional DTCs and definitions.
⑤ DOWN SCROLL BUTTON -- Moves down through menu
and submenu items in menu mode. When more than one DTC is
retrieved, moves down through the current screen to the next
screens for additional DTCs and definitions.
⑥ OBD II CONNECTOR -- Connects the scan tool to the vehicle’s
Data Link Connector (DLC).

2.2 Specifications
1) Display: Backlit, 128 x 64 pixel display with contrast adjustment
2) Operating Temperature: 0 to 50°C (32 to 122 F°)
3) Storage Temperature: -20 to 70°C (-4 to 158 F°)
4) External Power: 8.0 to 15.0 Volts provided via vehicle battery
5) Dimensions:
Length Width Height
178 mm (7.00”) 95 mm (3.75”) 34 mm (1.35”)
6) NW: 0.70kg (1.54lb), GW: 1.0kg(2.20lb)

2.3 Accessories Included
1) User’s Manual -- Instructions on tool operations
2) OBD2 cable -- Provides power to tool and communicates
between tool and vehicle
3) USB Cable -- Used to upgrade the scan tool
4) Carry Case -- A nylon case to store the scan tool when not in use.

2.4 Navigation Characters
Characters used to help navigate the scan tool are:
1) “►” -- Indicates current selection.
2) “↓” -- A flashing down arrow indicates additional information is
available on the next screen.

3

3)
“↑” -- A flashing up arrow indicates additional information is
available on the previous screen.
4) “pd” -- Identifies a pending DTC when viewing DTCs.

2.5 Keyboard
No solvents such as alcohol are allowed to clean the keypad or display.
Use a mild nonabrasive detergent and a soft cotton cloth. Do not soak
the keypad as the keypad is not waterproof.

2.6 Power
The external power of the scan tool is provided via the vehicle Data
Link Connector (DLC). Just follow the steps below to turn on the scan
tool:
1) Connect the OBD II Cable to scan tool.
2) Find DLC on vehicle.
A plastic DLC cover may be found for some vehicles and you
need to remove it before plugging the OBD2 cable.
3) Plug OBD II Cable to the vehicle’s DLC.

2.7 Product Setup
The scan tool allows you to make the following adjustments and
settings:
1) Contrast Adjustment: Adjusts the contrast of the LCD display.
2) Display Test: Tests the LCD display.
3) Keyboard Test: Tests the keyboard.
To enter the setup menu mode
1) From the keyboard: Press and hold the N button for at least 3
seconds until the System Setup menu shows up. Follow the
instructions to make adjustments and settings as described in the
following setup options.

4

System Setup
►1) Contrast
2) Display Test
3) Keyboard Test

2) From the Main Menu: Use the UP/DOWN Scroll Buttons to
select System Setup and then press the Y button. Follow the
instructions to make adjustments and settings as described in the
following setup options.

Main Menu
1) VW/AUDI
2) OBDII/EOBD
3) Oil Service
►4) System Setup

Contrast Adjustment
1) From the System Setup menu, use the UP/DOWN scroll buttons
to select Contrast, and press the Y button.

System Setup

►1) Contrast
2) Display Test
3) Keyboard Test

5

From the Contrast menu, use the UP/DOWN scroll buttons to increase or
decrease the contrast.

Contrast

Contrast （45%）

Use or to change

2) Press the Y button to save your selection and return to previous
menu.
3) Press the N button to return to previous menus.

Display Test
The Display Test is used to check the LCD display.
1) From the System Setup menu, use the UP/DOWN scroll buttons
to select Display Test and press the Y button.

System Setup

1) Contrast
►2) Display Test
3) Keyboard Test

2) Press the Y button again to start test. Look for missing spots in
the solid black characters.

6

Display Test
Press [Y] to test.
Look for missing
spots in characters.

Press <N> to return.

3) When completed, press the N button to return.

Keyboard Test
The Keyboard Test is used to verify that the keys are functioning
properly.
1) Use the UP/DOWN scroll buttons to select Keyboard Test from
System Setup menu, and then press Y button.

System Setup

1) Contrast
2) Display Test
►3) Keyboard Test

2) Press any key to start test. When you press a key, the key name
should be observed on the display. If the name does not show up,
then the key is not functioning properly.

7

Keyboard Test

Press any key to
Start test to
display name.
Key:

Double [N] to Return

3) Double press N to return to the previous menu.

2.8 Vehicle Coverage
The MaxScan VAG405 VW/AUDI Code Scanner is specially
designed to work with most Volkswagen and Audis sold worldwide of
1990 or newer models. If a VW/AUDI has a 16-pin "OBD-II style"
Data Link Connector (DTC), the code reader will certainly work. If it
has an old-style 2x2 Data Link Connector (DTC), then it depends on
whether there are 4 or 3 wires connecting to the pins. If there are 4
wires, each connecting a pin, then it will work. If there are only 3
wires, leaving one pin disconnected, then it will not work.
For VW/AUDI with old-style 2x2 Data Link Connector (DTC), you
need to have a 2x2 cabling adapter which is not included in this
product package.

8

3. Operating Instructions
3.1 VW/AUDI Diagnostics
Reading Codes
CAUTION: Don’t connect or disconnect any test equipment with
ignition on or engine running.
1) Turn the ignition off.
2) Locate the vehicle’s 16-pin Data Link Connector (DLC).
3) Plug the OBDII connector to the vehicle’s DLC.
4) Turn the ignition on. But do not start the engine.
5) Press the Y button. The Main Menu will be observed on the
display.
6) Use the UP/DOWN scroll buttons to select VW/AUDI from the
menu and press the Y button.

Main Menu
►1) VW/AUDI
2) OBDII/EOBD
3) Oil Service
4) System Setup

7) Use the UP/DOWN scroll buttons to select the system from the
Select System menu and press the Y button.

Select System

►01) Engine
02) Auto Trans
15) Airbags
03) ABS Brakes
08) Auto HVAC
09) Cent. Elect.

9

If the scan tool fails to communicate with the selected
vehicle’s ECU (Electronic Control Unit), a “LINK
ERROR!” message shows up on the display.
Verify that the ignition is ON;
Check if the scan tool’s OBD II connector is securely
connected to the vehicle’s DLC;
Verify that the module is supported;
Turn the ignition off and wait for about 10 seconds. Turn the
ignition back to on and repeat the procedure from step 5.
If the “LINK ERROR” message does not go away, then
there might be problems for the scan tool to communicate
with the module being tested. The most common cause is
that the scanned module is not supported on the vehicle.
The numbers (01, 02, 15, 03, 08, etc) in front of the system
names refer to the physical addresses assigned to the systems,
not the sequence of the systems to be arranged.
8) Select Read Codes from the Select Function menu and press the
Y button.

Select Function
►1) Read Codes
2) Erase Codes
3) ECU Information
4) Readiness Test

If there are no Diagnostic Trouble Codes present, the display
will indicate “NO CODES ARE STORED IN THE
MODULE!”
● If there are any Diagnostic Trouble Codes present, the DTC
number and its definition will show on the LCD display.
● The subcode, the communication protocol, the sequence of
the DTC currently being observed and the total number of
codes detected will be observed on the upper right hand
corner of the display.

10

● When a DTC’s definition covers more than one display
screen, use the Y button, as necessary, to view any additional
information.
If the DTC definition is not available, an advisory message
prompting you to refer to the vehicle service manual will be
observed on the display.
If more than one DTC is found, use the UP/DOWN scroll
buttons, as necessary, until all the codes have been shown up.

16627 --100 01/10
CAN BUS
↓
Solenoid Valve (A)
For Boost Pressure
Control (N75):
Malfunction: P0243

Erasing Codes
CAUTION: Erasing the Diagnostic Trouble Codes may allow the
scan tool to delete not only the codes from the vehicle’s on-board
computer, but also “Freeze Frame” data and manufacturer specific
enhanced data. Further, the I/M Readiness Monitor Status for all
vehicle monitors is reset to Fail status. Do not erase the codes before
the system has been checked completely by a technician.
1) If you decide to erase the DTCs, use the UP/DOWN scroll
buttons to select Erase Codes from Select Function menu and
press the Y button.

11

Select Function

1) Read Codes
►2) Erase Codes
3) ECU Information
4) Readiness Test

If the scan tool is not connected or no communication is
established with the vehicle yet, then refer to Reading Codes
from 1 to 7 at Paragraph 3.1.
2) A warning message comes up asking for your confirmation.

Erase Codes

Erase Trouble Codes!
Are you sure?
<YES> NO

3) If you do not want to proceed with erasing the codes, press the N
button to exit. A message of “command cancelled” will show up.
4) If you do wish to proceed to erase the codes, then press the Y
button.
5) If the codes are cleared successfully, an “ERASE DONE!”
confirmation message will show on the display. Press any button
to return to the previous menus.
6) If the codes are not cleared, then an “ERASE FAILURE!”
message will appear. Press the N button to return to previous
menus.

12

Viewing ECU Information
1) To view ECU Information, use the UP/DOWN scroll buttons
to select ECU Information from Select Function menu and
press the Y button.

Select Function
1) Read Code
2) Erase Code
►3) ECU Information
4) Readiness Test

● If the scan tool is not connected or no communication is

ECU Information
VAG No.: 06A906032TF
Component:
Bosch 1.815VT
0020
Coding: 0008570
Imp: 0000 WSC: 000078

If there is no ECU Information available, a warning message
shows on the display.

Readiness Test
Important: The Readiness Test function is used to check the
operations of the Emission System on OBD2/EOBD compliant
vehicles. It is an excellent function to use prior to having a vehicle
inspected for compliance to an emissions program.

13

“Pass” -- Indicates that a particular monitor being checked has
completed its diagnostic testing.
“Fail” -- Indicates that a particular monitor being checked has
not completed its diagnostic testing or the monitor is not
supported on that vehicle.
1) Use the UP/DOWN scroll buttons to select Readiness Test from
Select Function menu and press the Y button.

Select Function
1) Read Code
2) Erase Code
3) ECU Information
►4) Readiness Test

If the scan tool is not connected yet, then refer to Reading
Codes from 1 to 7 at Paragraph 3.1.
2) Use the UP/DOWN scroll buttons, as necessary, to view the status
of the following monitors:
EGR Sys.-- EGR System Monitor
O2 Sensor(s) -- O2 Sensors Monitor
Catalyst -- Catalyst Monitor
EVAP Sys. -- Evaporative System Monitor
Heated O2 --O2 Sensor Heater Monitor
Sec Air Inject -- Secondary Air Monitor
A/C -- A/C system Monitor
Catalytic Conv. -- Catalytic Convertor Monitor

14

Readiness Test
↓
EGR Sys. Pass
Heated O2 Pass
O2 Sensor(s) Pass
A/C Pass
Sec. Air Inject Pass
EVAP Sys. Fail


3.2 OBDII/EOBD Diagnostics
Reading Codes
CAUTION: Don’t connect or disconnect any test equipment with
ignition on or engine running.
display.
6) Use the UP/DOWN scroll buttons to select OBDII/EOBD from
the menu.

Main Menu

1) VW/AUDI
►2) OBDII/EOBD
3) Oil Service
4) System Setup

7) Press the Y button. A sequence of messages showing the
OBDII/EOBD protocols will be observed on the display until the
vehicle protocol is detected.

15

If the scan tool fails to communicate with the vehicle’s ECU
(Engine Control Unit), a “LINK ERROR!” message shows
up on the display.
Verify that the vehicle is OBDII/EOBD compliant;
ignition back to on and repeat the procedure from step 5.
If the “LINK ERROR” message does not go away, then there
might be problems for the scan tool to communicate with the
vehicle. Contact your local distributor or the manufacturer’s
customer service department for assistance.
8) After the vehicle protocol is displayed on the screen, press any key or
wait about 2 seconds for the OBDII/EOBD DIAG. menu to come up.
9) Use the UP/DOWN scroll buttons to select Read Codes from the

OBDII/EOBD DIAG.
►1) Read Codes
2) Erase Codes

If there are no Diagnostic Trouble Codes present, the display
will indicate “NO CODES ARE STORED IN THE
MODULE!”
If there are any Diagnostic Trouble Codes present, the Fault
Codes and Pending Codes will be reported on the display.

16

P0118 Pd 06/06
ISO9141 $09
↓
Pressure Control
Solenoid A Control
Circuit Low

● The DTC number will appear on the upper left hand corner
and its definition will show on the body of screen.
● The type of code (Generic or Manufacturer specific), the
vehicle protocol, the sequence of the DTC currently being
observed, the total number of codes detected and the module
ID will be observed on the upper right hand corner of the
display.
● If the code being displayed is a pending code, the Pd icon will
be observed next to the DTC number on the upper right hand
corner of the display.
● When a DTC’s definition covers more than one display screen,
use the Y button, as necessary, to view any additional
information.
If the retrieved DTCs contain any manufacturer specific or
enhanced codes, you will be prompted to refer to the CD DTC
library or the vehicle service manual to view the DTC
definitions.
10) If more than one DTC is found, use the UP/DOWN scroll buttons,
as necessary, until all the codes have been shown up.

Erasing Codes
1) If you decide to erase the DTCs, use the UP/DOWN scroll
buttons to select Erase Codes from the OBDII/EOBD DIAG.

17

OBDII/EOBD DIAG.
►1) Read Codes
2) Erase Codes

If the scan tool is not connected or no communication is
2) A warning message comes up asking for your confirmation.

Erase Codes
Erase Trouble Codes!
Are you sure?
<YES> NO

3) If you do not want to proceed with erasing the codes, press the N
button to exit. A message of “command cancelled” will show up.
4) If you do wish to proceed to erase the codes, then press the Y
button.
5) If the codes are cleared successfully, an “ERASE DONE!”
confirmation will show on the display. Press any button to return
to previous menus.
6) If the codes are not cleared, then an “ERASE FAILURE!”
message will appear. Press the N button to return to previous
menus.

3.3 Oil Service
18

display.
6) Use UP/DOWN scroll button to select Oil Service from the menu,
and press the Y button.
Main Menu
1) VW/AUDI
2) OBDII/EOBD
►3) Oil Service
4) System Setup

If the scan tool fails to communicate with the vehicle, a
“LINK ERROR!” message shows up on the display.
ignition back on.
If the “LINK ERROR” message does not go away, then
there might be problems for the scan tool to communicate
with the vehicle. Contact your local distributor or the
manufacturer’s customer service department for assistance.

A. Automatic Vehicle Detect
1) Use UP/DOWN scroll button to select All, and press Y button.

19

Oil Service

►1) All
2) Audi(up to 2000)
3) VW(up to 2000)
4) Seat(up to 2000)
5) Skoda(up to 2000)

All option can be used to detect all VAG vehicles before and
after 2000 automatically.

Automatic Services Detect
The Auto Detect function is used to detect services automatically.
2) Use UP/DOWN scroll button to select Auto Detect and press Y
button to confirm.

Oil Service

►1) Auto Detect
2) Longlife Oil
3) Non Longlife Oil
4) Set Insp. Interval

3) Wait a few seconds till the following screen shows.

Oil Type

►01) Fixed Service
02 Flexible-Gasoline
03) Flexible-Diesel

20

4)
Use UP/DOWN button to select oil type that your vehicle uses
and press Y button.

Select Function

►01) Oil Insp. Light
02) Set Insp. 1
03) Set Insp. 2

Different vehicle supports different oil service functions, so
the displayed functions vary from one vehicle to another.
5) Select the oil service function that your vehicle supports and
press Y button. Wait a few seconds while the scan tool is
performing service resetting.

Oil Insp. Light

Service setting…

-Please Wait-

6) A message “RESET OK” comes up, indicating oil service reset is
completed.

Oil Service

RESET OK!

Press any key to cont.

21

7)
If the vehicle can not be detected automatically, following screen
shows. You need to perform oil service setup manually.

Oil Service

Can’t Auto Detect!
Please try others!

Press any key to con.

8) Wait a few seconds or press any key to start reading channel data.

Manual

Reading Channel Data…

-Please Wait-

9) Use UP/DOWN button to change set value.

Min Mil. to Service
1/3
Channel No 42 (Mil)
Current Value 9000
Set Value 9000

[N] = Next, [Y] = Save/Exit
[︽]/[︾] = Change Setup

x/x to the upper right part of the screen indicates total number
of supported service channels and the sequence of current
channel.
10) Use N button to move to next setup screen.

22

Mil. Since Service
2/3
Channel No 40 (Mil)
Current Value 700
Set Value 700


Different vehicle supports different oil service channels, so
retrieved channel numbers vary from one vehicle to another.
Normally, a vehicle supports 1-5 channels.
“Current Value” is the value of the most recent setup
retrieved by the scan tool. If you change your mind after
making new setups, it can be used to reset all changed values
to the original ones. Write down this value before making any
changes.
11) Use UP/DOWN scroll button to select Save and press Y button
to save your settings.

Oil Service

Back Save Exit
[Back] = Cont. to Set
[Save] = Save Setup
[Exit] = Cancel Setup

If you want to continue to set values, use UP/DOWN scroll
button to select Back and press Y button to return to continue
setup. If you want to cancel all setups, use UP/DOWN scroll
button to select Exit and press Y button, or simply press N
button to exit.
12) Wait a few seconds till the “RESET OK!” message comes up.
Press any key to return to Main Menu.

23

Manual Setup

RESET OK!


Resetting Longlife Oil Service
The Longlife Oil function is used to reset long life oil service.
1) Use UP/DOWN scroll button to select Longlife Oil from the
menu, and press Y button.

Oil Service

1) Auto Detect
►2) Longlife Oil
3) Non Longlife Oil

2) Use UP/DOWN scroll button to select Service Reset from
Longlife Oil menu, and press Y button.

Longlife Oil

►1) Service Reset
2) Set Oil Type
3) View Oil Type

3) Press any key to return to Longlife Oil menu.

24

Service Reset

RESET OK!


4) To set oil type, use UP/DOWN scroll button to select Set Oil
Type from Longlife Oil menu, and press Y button.

Set Oil Type

►1) Diesel
2) V6Tdi
3) Petrol
4) Non Longlife Oil

5) Use UP/DOWN scroll button to select the oil type your vehicle
uses.
6) Press any key to return to Longlife Oil menu.

Oil Type Reset

RESET OK!


7) To view oil type, use UP/DOWN scroll button to select View Oil
Type from Longlife Oil menu, and press Y button.

25

Longlife Oil

1) Service Reset
2) Set Oil Type
►3) View Oil Type

8) View oil type on screen and press any key to return to Lifelong
Oil menu.

View Oil Type

Non longlife Oil


Resetting Non Longlife Oil Service
The Non Longlife Oil function is used to reset non long life oil service.
1) To reset non longlife oil service, use UP/DOWN scroll button to
select Non Longlife Oil from the Oil Service menu, and press Y
button.

Oil Service

1) Auto Detect
►2) Longlife Oil
3) Non Longlife Oil

2) Use UP/DOWN scroll button to select Service Reset from
Non Longlife Oil menu, and press Y button.

26

Non Longlife Oil

►1) Service Reset

3) Press any key to return to previous menu.

Service Reset

RESET OK!


Setting Inspection Interval
The Set Insp. Interval function is used to set oil service interval of
different channels.
1) Use UP/DOWN scroll button to select Set Insp. Interval, and
press Y button.

Oil Service

1) Auto Detect
►2) Longlife Oil
3) Non Longlife Oil

2) Wait a few seconds till the following screen shows.

27

Oil Service

RESET OK!


3) If the oil service reset is not automatically performed by the scan
tool, the following screen appears. You need to perform manual
setup.

Manual

Reading Channel Data…

-Please Wait-

4) Use UP/DOWN scroll button to change set value.

Min Mil. to Service
1/3
Channel No 42 (Mil)
Current Value 9000
Set Value 9000


5) Use N button to move to next setup screen.

28

Mil. Since Service
2/3
Channel No 40 (Mil)
Current Value 700
Set Value 700


6) Use UP/DOWN scroll button to select Save and press Y button
to save your settings.

Oil Service

Back Save Exit
[Back] = Cont. to Set
[Save] = Save Setup
[Exit] = Cancel Setup

7) Press any key to return to Main Menu.

Manual Setup

RESET OK!


If you want to continue to set values, use UP/DOWN scroll
button to select Back and press Y button to continue to change
set values. If you want to cancel all setups, use UP/DOWN
scroll button to select Exit and press Y button, or simply press
N button to exit.

29

B. Manual Vehicle Selection
1) If you want to select vehicle manually, use UP/DOWN scroll
button to select Oil Service from Main Menu, and press the Y
button.

Main Menu
1) VW/AUDI
2) OBDII/EOBD
►3) Oil Service
4) System Setup

2) Use UP/DOWN scroll button to select vehicle make, and press Y
button to confirm.

Oil Service

1) All
►2) Audi(up to 2000)
3) VW(up to 2000)
4) Seat(up to 2000)
5) Skoda(up to 2000)

3) Use UP/DOWN scroll button to select vehicle model year, and
press Y button to confirm.

Select Vehicle
↓
01) Golf 3
02) Golf 4
►03) New Beetle
04) Passat
05) Passat B5
06) Passat 97

30

4)
Use UP/DOWN scroll button to select the oil service function
that your vehicle supports.

Select Function

►01) Oil Insp. Light
02) Set Insp. 1
03) Set Insp. 2

5) Wait a few seconds till the following screen appears.

Oil Service

RESET OK!


If a message “Service reset failed!” comes up, repeat the
procedure from Step 3 or use Auto Detect to detect service
automatically.
If the message “Service reset failed!” does not go away,
ignition back on.
If the scan tool still fails to perform oil service reset, contact
your local distributor or the manufacturer’s customer service
department for assistance.

31

4. Warranty and Service
4.1 Limited One Year Warranty
Autel warrants to its customers that this product will be free from all
defects in materials and workmanship for a period of one (1) year from
the date of the original purchase, subject to the following terms and
conditions:
1) The sole responsibility of Autel under the Warranty is limited to
either the repair or, at the option of Autel, replacement of the scan
tool at no charge with Proof of Purchase. The sales receipt may be
used for this purpose.
2) This warranty does not apply to damages caused by improper use,
accident, flood, lightning, or if the product was altered or repaired
by anyone other than the Manufacturer’s Service Center.
3) Autel shall not be liable for any incidental or consequential
damages arising from the use, misuse, or mounting of the scan
tool. Some states do not allow limitations on how long an implied
warranty lasts, so the above limitations may not apply to you.
4) All information in this manual is based on the latest information
available at the time of publication and no warranty can be made
for its accuracy or completeness. Autel reserves the right to make
changes at any time without notice.

4.2 Service Procedures
If you have any questions, please contact your local store, distributor
or visit our website at www.auteltech.com.
If it becomes necessary to return the scan tool for repair, contact your
local distributor for more information.

32

Autel max scan vag405 code reader obd2 eobd can bus vw audi

More Related Content

Similar to Autel max scan vag405 code reader obd2 eobd can bus vw audi (20)

More from autoobdtools (20)

Recently uploaded (20)

Autel max scan vag405 code reader obd2 eobd can bus vw audi