Automatic collision detection for an autonomous robot using proximity sensing technology on an avr hardware platform

IJRET: International Journal of Research in Engineering and Technology eISSN: 2319-1163 | pISSN: 2321-7308
_______________________________________________________________________________________
Volume: 03 Issue: 06 | June-2014, Available @ http://www.ijret.org 214
AUTOMATIC COLLISION DETECTION FOR AN AUTONOMOUS
ROBOT USING PROXIMITY SENSING TECHNOLOGY ON AN AVR
HARDWARE PLATFORM
Anish Kumar1
, Ramandeep Singh2
1
PG Student M.Tech (ES), EECE Department, ITM University, Gurgaon, Haryana, India
2
Assistant Professor, EECE Department, ITM University, Gurgaon, Haryana, India
Abstract
This work is concerned about making an anti-collision device. Primary goal of anti-collision device is to identify the collision and
report it to control panel. Automatic collision detection is an advance area of research. Collision are catastrophic and a mass
destructive force. This will harm property and life both. Now day collision detection is the one of most important algorithm used
in autonomous vehicle development phases. Actuator takes Input through sensor module. To belt that system, we are using
proximity sensor, AVR controller and motors. This program code simulated using proteus software as real like environment to
identifying anti-collision.
Keywords: AVR microcontroller, Proximity Sensor, Protus, Anti-Collision System, Autonomous Vehicle, Actuator.
--------------------------------------------------------------------***----------------------------------------------------------------------
1. INTRODUCTION
Every mechanism, which having moving parts, needs some
safety measure. The human error or system failure with
machine raises the happening of undesired events. Our
purpose to work on anti-collision device is to make an anti
collision zone, make device portable. Other factor can also
be involved like high speed response and low cost. Collision
avoidance is one of the most difficult domains of intelligent
vehicle. This is also known as pre-clash or forward collision
warning system. Various sensor are used in making of anti
collision system i.e. laser, camera, radar, ultrasonic, GPS
etc. to detect the eminent crash [1] [5]. Once the detection
has been done this system warn the driver or action is taken
through actuators without driver interference. The different
actuators are like servo motor, relays, driving wheel and
breaks etc.
A collision detection system is an automatic self driven
system for the safety. Such system is designed to reduce the
surveillance of accident. The major hardware part of the
system will be camera, sensor, and microcontroller [1] [3]
[7] [10]. System is designed in such a manner so that it
should be more reliable and efficient for detecting not only
the imminent crash but also low cost and power efficient
system[11][12]. As soon as the detestation is there the
system either warn or will take imminent action without
driver input.
It is one of the major parts of autonomous vehicles. As an
autonomous vehicle, it is capable of sensing its environment
and navigating without human input. Zigbee is also one of
the cheap technology is being used as a communication
service provider between the nodes [2] [4] [7] [10].Zigbee
has defined data rate of 250kbps. The GPS and GSM
technologies being merged with collision detection
algorithms for better reliability [6] [11] Robotic cars exist
mainly as prototypes and demonstration systems. We can
take any technique for taking input from external world like.
Simulation is being done on proteus [5]. Purpose of
simulating the design is presenting the possibilities for its
implementation like robots, cars, railway etc [5] [8]. Also
ARM based processer is being used for making ACD (Anti
Collision Detection) [6] [10]. Collision can be vehicle to
vehicle or can be vehicle to infrastructure. Intra-vehicle
communication between two different vehicles will help in
detecting and avoiding collision [9].
2. BLOCK DIAGRAM
Fig-1: Block Diagram of collision detection using proximity
sensor

_______________________________________________________________________________________
One block diagram shows the flow of data in different
sections. In block diagram there are shown six blocks
proximity sensor, ADC, ATMEGA board, motor driver
circuit, DC motor and LCD. All development blocks in a
single platform they communicate with external world
through sensor array with its very first block. That analog
input will be processed by the ADC in ATMEGA board. An
motor driver circuit is used for the proper functioning of the
DC motor driver circuit takes the output from the ports of
the ATMEGA board and drive the motor next connected to
it. Because signal coming out of the controller are not well
enough to drive the motor so in that case motor driver helps
in. One LCD unit is also been there for displaying the
activation of motor like is that motor in stop, run, clockwise
or anticlockwise condition. As in here we are using
proximity sensor which helps in detecting low range
collision. Microcontroller selection requires sufficient
input/output control lines, processing speed and adequate
memory for running the entire program and additional serial
ports, Timers, counters, PWM etc. We are choosing AVR
AT mega 128 controllers. It’s a 8 bit controller based on
advance RISC architecture, highly endure non-volatile
memory segment and with all special feature like power-on
reset , Internal Calibrated RC Oscillator, External and
Internal Interrupt Sources, Six Sleep Modes, ADC Noise
Reduction, Power-save, Power-down, Standby, and
Extended Standby, Software Selectable Clock Frequency
etc. In sensor block we can use any module of sensor
according to the design application. The selection of ADC
using is according to the sensitivity we required like 10, 12,
16 bits. In the controller block we are using ATmega128
development board.
3. FLOW CHART/ALGORITHM
Flow chart represent that how data will flow and when the
decision time comes. How system will react to the situation
when more than one decision has to make. Action will be
taken in which sequence. After starting two decision blocks
one is of active transmission and other is of receiver.
Transmission block is in loop with starting till they are not
active when this will active decision comes to receiver. That
decision is in loop with the output of transmitter. In this
flowchart from starting we check for the sensor array is
active or not then if value is send by the received then
correspondent output will be fetch on the port. Next we
choose the concept of port to port transfer of data. We do
control the operation of DC motor. We are using a sensor
module. The sensor module needs 5V for their operation.
Output signal will be in form of voltage level. That voltage
level we are getting on ADC. ADC converts that voltage
signal into binary output. Respectively binary output has
been taken on the port. According to the port value. We
select the values for motor operation on other port. Values
for motor port is designed by using if else condition. As we
can see in flow chart process block of motor are connected
with decision blocks using if-else statement.
We are designing algorithm in such a way so that when
there is no object our robot run freely in straight line and
according to the intensity of signal coming from sensor
response of the robot will be different i.e. start, turn right,
turn left, stop etc.
Fig-2: Flow Chart
They are continuously in loop. One time only one process
block of motor is active. That is chosen accordingly what
our sensor is capturing.
In above flow chart sensor takes the information. That is, is
the object being placed on the way as obstacle? Then it
inform to the brain of the system (to processer) whose
purpose is to start and stop the motor accordingly. A
continuous collision detection algorithm is there. The
algorithm is designed in such a way so that for any detection
of collision system get alert. First it will respond in the form
of error then stop or change its direction. We can also
increase the number of sensor input to microcontroller like
left sensor unit, right sensor unit, front and back unit for
robot car for make it more reliable.

_______________________________________________________________________________________
4. PROTEUS SIMULATION SOFTWARE:
Fig-3: Simulation on Proteus
5. APPLICATION AREA
There are verities of application of an automatic collision
detection device. Some of them are like in space application,
an intelligent self driven car, railway and metro automation,
intelligent robots, traction control system, dynamic steering
response, intelligent parking, traffic signal recognition,
intelligent speed adaptive system.
There are endless scopes of this idea. This idea is easy
adaptable with latest technology. We can merge different
technology for making one of the best automatic collision
devices. These devices can use in military, hospitals, traffic
control, space application etc.
6. ADVANTAGES & LIMITATION
A vehicle with automatic collision detection system will
increase the reliability. It increases capacity t roads and
higher speed limit for autonomous car. In autonomous car it
would not matter, if the occupant is under age, over age,
intoxicated or blind. Not-collision car and autonomous car
can go for pick up the passenger without driver. This will
also help in reduction the physical road signage. This
vehicle can operate themselves in environment like where
impossible to go for human and operate themselves
automatically.
This system mainly reduces the driver stress if it’s a semi
automatic or can give warning in advance on dash board. If
system is connected with GPS then it’s easier to find the
condition of roads.
The main disadvantage of the system if that we can’t totally
depends on system response. Information given by the
sensor can mislead the person if the orientation of the sensor
and camera is changed from a particular position. The
collision detection system is also get effected by the
environmental conditions like by dust, fog etc. Algorithm
designed will be more complex because multiple tasks are
being given to single processer when there are multiple tasks
in an autonomous vehicle. Tasks are chosen to be done
according to the priority and severity. Response of the
system should be in fraction of second otherwise imminent
crash can happen.
Vehicle with anti-collision system will increase the cost
because it requires additional vehicle equipment, service,
maintenance and possibly additional roadway infrastructure.
Also additional risk such as system failure, be less reliable
under some critical condition etc. Security for information
abuse, failure of GPS system can cause problem. Over-
ridden of automatic collision algorithm by manual operation
can also creates problem. Collision prevention assistance
requires a sufficient radar reflectance of objects and
efficiency of sensor are compromised by snow, mud or
leaves.
7. RESULT
Our system is working for small range of operation and
collision is being detected and when collision being detected
it might stop or turn as per program develop.
As following the result of motor motion has shown on LCD
screen i.e. start, clockwise, anticlockwise, stop etc.
Fig- 4: Interface screen
8. CONCLUSIONS
The embedded system for collision detection can ensure the
protection and operation of autonomous robots in the
condition where zero human interference. If we see this
technology with its future there are endless development
scope and technology we can merge with it. Everything will
became automatic and also sending status information to
owner about collision happening or not.
ACKNOWLEDGEMENTS
I am deeply grateful to the professors, faculties and
technical staff of Electrical, Electronics & Communication
Engineering of ITM University, Gurgaon by whose support
I was able to complete my research work. I want to thanks
my friends also who were involved in their research work
and same time they help me with their practical experience.

_______________________________________________________________________________________
REFERENCES
[1]. Frederic Maire “Vision Based Anti-collision System for
Rail Track Maintenance Vehicles”, Australia Faculty of IT,
Queensland University of Technology.
[2]. Arun P; Sabarinath G; Palai, Kottayam,; Madhukumar
S; Careena P “Collision And Level Crossing Protection
System for Indian Railways” International Journal of Latest
Trends in Engineering and Technology (IJLTET).
[3]. CH. ANUSHA1, CH.V.S.GOPINATH2, P.
NAGAMALLAIAH3 “ANTI COLLISION DEVICE
BETWEEN TRAINS USING ZIGBEE” International
Conference on Electronics and Communication Engineering
(ECE) 7th April 2013, Bangalore,ISBN:978-93-82208-84-6.
[4]. Arun.P ; Saritha.S ; Madhukumar.S “Simulation of
Zigbee based Tacs for Collision Detection and Avoidance
for Railway Traffic” Special Issue of International Journal
of Computer Applications (0975 – 8887) on Advanced
Computing and Communication Technologies for HPC
Applications - ACCTHPCA, June 2012.
[5]. SANDHYA GAUTAM;SANDIP NEMADE;TEENA
SAKLA “SIMULATION OF AN ANTI-COLLISION
SYSTEM ON SAME TRACK FOR RAILWAYS” Sandhya
Gautam et. al. /International Journal of Engineering and
Technology Vol. 2(9), 2010, 4832-4837.
[6]. J.D.Prathusha, K.S.Roy , Mahaboob Ali “ARM Cortex
M3 Based Collision Detection System” International Journal
of Engineering Trends and Technology (IJETT) -
Volume4Issue5- May 2013.
[7]. G.Anjali bissa, S.Jayasudha, R.Narmatha and
B.Rajmohan “ Train Collision Avoidance System Using
Vibration Sensors And Zigbee Technology” IJREAT
International Journal of Research in Engineering &
Advanced Technology, Volume 1, Issue 1, March, 2013
ISSN: 2320 – 8791.
[8]. Rossi Passarella, Bambang Tutuko & Aditya P.P.
Prasetyo “ DESIGN CONCEPT OF TRAIN OBSTACLE
DETECTION SYSTEM IN INDONESIA” IJRRAS 9 (3)
December 2011.
[9]. Thomas Strang, Michael Meyer zu Hörste, Xiaogang Gu
“ A RAILWAY COLLISION AVOIDANCE SYSTEM
EXPLOITING AD-HOC INTER-VEHICLE
COMMUNICATIONS AND GALILEO” German
Aerospace Center (1)Institute of Communications and
Navigation (2)Institute of Transportation Systems.
[10]. Mr. N. Sambamurthy, Sk. Hasane Ahammad, “
Prevention of Train Accidents Using Wireless Sensor
Networks” Int. Journal of Engineering Research and
Applications ISSN : 2248-9622, Vol. 3, Issue 6, Nov-Dec
2013, pp.1592-1597.
[11]. Richard W. Wall , Jerry Bennett, Greg Eis, Kevin
Lichy, and Elizabeth Owings, “CREATING A LOW-COST
AUTONOMOUS VEHICLE” Students, University of Idaho
Electrical and Computer Engineering Dept.Moscow.
[12]. Raja Jurdak, Kevin Klues, Brano Kusy, Christian
Richter, Koen Langendoen, and Michael Brünig “Opal: A
Multiradio Platform for High Throughput Wireless Sensor
Networks” IEEE EMBEDDED SYSTEMS LETTERS,
VOL. 3, NO. 4, DECEMBER 2011.
BIOGRAPHIES
Anish Kumar is currently is doing Post
Graduation in Embedded Systems from
ITM University, Gurgaon. He completed
his B.Tech in Electrical Engineering from
Chitkara Institute of Engineering and
Technology Rajpura, Chandigarh under
Punjab Technical University Jalandher in 2011. His area of
interest is Embedded System Design and Real Time
Systems.
Ramandeep Singh is an Assistant
Professor in EECE Department of ITM
University, Gurgaon. He is pursuing PhD
in embedded systems from ITM
University. In 2009 he has completed
M.E. in embedded systems. He is a B.
Tech. graduate from GGSIPU, Delhi. His core research
areas are low power embedded systems, robotics, FPGA
based embedded systems and SCADA. Prior to joining ITM
University he has worked with NXP Semiconductors,
Bangalore. He has various publications in international
journals and conferences.

Automatic collision detection for an autonomous robot using proximity sensing technology on an avr hardware platform

More Related Content

What's hot (19)

Viewers also liked (20)

Similar to Automatic collision detection for an autonomous robot using proximity sensing technology on an avr hardware platform (20)

More from eSAT Publishing House (20)

Recently uploaded (20)

Automatic collision detection for an autonomous robot using proximity sensing technology on an avr hardware platform