Avr book

2014
INTRODUCTION TO AVR
GETTING STARTED WITH
1. AVR STUDIO
2. AVR OSP
3. SINA PROG
INTERFACING
1. LCD,KEYPAD
2. ADC,I2C,SERIAL,PWM
ATMEGA DEVELOPMENT BOARD
Programming With AVR
Microcontroller

Atmega 16/32 Microcontroller
www.researchdesignlab.com Page 1
ATMEGA 16/32
MICROCONTROLLER

Table of Contents
OVERVIEW:.............................................................................................................................................. 3
PORTS:...................................................................................................................................................................3
PIN DESCRIPTION: ................................................................................................................................ 5
WRITING THE CODE ............................................................................................................................. 7
1. AVR STUDIO ..................................................................................................................................................7
BURNING THE CODE...........................................................................................................................14
1. AVR osp-2.................................................................................................................................................... 14
2. SINA PROG 2.1............................................................................................................................................. 22
INTERFACE.............................................................................................................................................25
1. LED BLINKING.............................................................................................................................................. 25
2. LCD.............................................................................................................................................................. 27
3. PULSE WIDTH MODULATION.......................................................................................................................30
4. ADC ............................................................................................................................................................. 32
5. KEYPAD ....................................................................................................................................................... 36
SERIAL COMMUNICATION:...............................................................................................................39
What is the USART?............................................................................................................................................. 39
Setting up the Hardware...................................................................................................................................... 39
Setting up HyperTerminal.................................................................................................................................... 40
Initializing the USART........................................................................................................................................... 43
Sending and receiving data..................................................................................................................................44
CODE: .................................................................................................................................................................. 45

OVERVIEW:
ATmega16 is an 8-bit high performance microcontroller of Atmel’s Mega AVR
family with low power consumption. Atmega16 is based on enhanced RISC
architecture with 131 powerful instructions. Most of the instructions execute in one
machine cycle. Atmega16 can work on a maximum frequency of 16MHz.
PORTS:
There are 32 I/O (Input/Output) pins grouped as A, B, C & D with 8 pins in each
group. This group is called as PORT.
PA0 - PA7 (PORTA)
PB0 - PB7 (PORTB)
PC0 - PC7 (PORTC)
PD0 - PD7 (PORTD)
These are additional function that pin can perform other
than I/O. Some of them are.
• ADC (ADC0 - ADC7 on PORTA)
• UART (Rx,Tx on PORTD)
• TIMERS (OC0 - OC2)
• SPI (MISO, MOSI, SCK on PORTB)
• External Interrupts (INT0 - INT2)

PIN DESCRIPTION:
• VCC: Digital supply voltage. (+5V)
• GND: Ground. (0 V) Note there are 2 ground Pins.
• Port A (PA7 - PA0)
Port A serves as the analog inputs to the A/D Converter. Port A also serves
as an 8-bit bi-directional I/O port, if the A/D Converter is not used. When
pins PA0 to PA7 are used as inputs and are externally pulled low, they will
source current if the internal pull-up resistors are activated. The Port A pins
are tri-stated when a reset condition becomes active, even if the clock is not
running.
• Port B (PB7 - PB0)
Port B is an 8-bit bi-directional I/O port with internal pull-up resistors
(selected for each bit). Port B also serves the functions of various special
features of the ATmega16 as listed on page 58 of datasheet.
• Port C (PC7 - PC0)
Port C is an 8-bit bi-directional I/O port with internal pull-up resistors
(selected for each bit). Port C also serves the functions of the JTAG
interface and other special features of the ATmega16 as listed on page 61 of
datasheet. If the JTAG interface is enabled, the pull-up resistors on pins
PC5 (TDI), PC3 (TMS) and PC2 (TCK) will be activated even if a reset
occurs.
• Port D (PD7 - PD0)
Port D is an 8-bit bi-directional I/O port with internal pull-up resistors
(selected for each bit). Port D also serves the functions of various special
features of the ATmega16 as listed on page 63 of datasheet.

• RESET: Reset Input. A low level on this pin for longer than the
minimum pulse length will generate a reset, even if the clock is not
running.
• XTAL1: External oscillator pin 1
• XTAL2: External oscillator pin 2
• AVCC: AVCC is the supply voltage pin for Port A and the A/D
Converter. It should be externally connected to VCC, even if the
ADC is not used. If the ADC is used, it should be connected to VCC
through a low-pass filter.
• AREF: AREF is the analog reference pin for the A/D Converter.

WRITING THE CODE
1. AVR STUDIO
Setup:
1. open AVR studio 4
2. click new project
3. Select AVR GCC as we would be doing program in c and enter the
project name.

4. Add your project name. Here I have given my project name as serial and
it will automatically create your initial file name in .c format
5. click on next

6. Select AVR simulator in debug platform and in the Device select the
Device your using as here I am using ATmega 16 i have selected that.(for
Atmega 32 select Atmega 32).
7. click on finish

8. This is the default window you will see after you click on finish and
project name called serial will get open
9. Now click on this to create a new file
10. Type the program and save it .To compile the files first you need to add
files in your source for doing that right click on the source file and then

click on add existing source file
11.Now inside that source file their will be your file saved here the file
name I have used is urted

12. Now to build the file go to build and click on build

13. If your program has no errors it will be successfully build and it will
show the build window like this
TO BURN THE PROGRAM IN YOUR MICROCONTROLLER YOU NEED A BURNER
FOR BURNING WE USE AVR OPS-2

BURNING THE CODE
1. AVR osp-2
1. click on avr osp
2. The default avr osp 2 will look like this

3. First you need to configure your avr osp to check its connected to the
same com port or not and default Baud rate

4. you can manually select the device which you are using or else u can
even auto detect it
5. In device select which device you are using as here I am using
ATmega 16 I have selected that .Even you can Auto Detect your
device that option will automatically Detect your Device which you

are using
6. after pressing auto detect you will see this means that your
microcontroller has been detected and it read to flash program on to it
7. To flash the program on the Microcontroller You Browse the program
and Then click on program after click on the program it will flash the

program.

8. Browse your hex file where you have store
9. After clicking on program it will erase the previous content of the chip
and will flash the program on to the chip

10. After the completion of the flash it will compare the flash data if its
equal than it means that your flash is successful and it will show
“Equal”

2. SINA PROG 2.1
• If You are using ISP Atmega Programmer to Burn the code In Your Microcontroller than this
Programmer will surely come in handy
• Its simple to use and You can easily use the Microcontroller For External Crystal Frequency

• If You Want to Change Internal Frequency Or want To use External Crystal Frequency than You
can change the Fuse.
• Here You Can Set Internal Frequency To
1. 1 MHz
2. 2 MHz
3. 4 MHz
4. 8 MHz
• If You want to use External Frequency than select Ext.Crys.
(If Ext Crys Doesn’t work properly than Try changing the BC valve as shown in Below Pic)

• Usually For Atmega 16 it comes out to be BC 32 KHz and For Atmega 32 BC 16 KHz but try with
Other Valve if this Doesn’t Works.

INTERFACE
1. LED BLINKING
Here we are blinking the led making it on and off for a certain duration using
AT Mega 16
Circuit diagram:

Program:
# define F_CPU 1000000UL
#define FOSC 16000000L //here we define the clock frequency
#include <avr/io.h>
#include <util/delay.h>
int main(void)
{
DDRB = 0xFF; //Makes PORTC as Output
While (1) //infinite loop
{
PORTB = 0xFF; //Turns ON All LEDs
_delay_ms(1000); //1 second delay
PORTB= 0x00; //Turns OFF All LEDs
_delay_ms(1000); //1 second delay
}
}

2. LCD :
CIRCUIT DIAGRAM:
Program:
#include <avr/io.h>
#include <string.h>
//#define LCD_PORT PORTB
#define RS PC0 //initialize register select as PC0 pin
#define EN PC1 //initialize enable pin as PC1

void CMD_WRT(unsigned char val)
{
PORTB=val;
PORTC = PORTC & (~(1<<RS));
_delay_ms(1); // here we provide a delay of 1 sec
ORTC = PORTC | ((1<<EN)); //make enable pin high
_delay_ms(1);
PORTC = PORTC & (~(1<<EN)); //make enable pin low
}
void DATA_WRT(unsigned char ch)
{
PORTB = ch;
PORTC = PORTC | ((1<<RS));//make register select pin high
_delay_ms(1);
PORTC = PORTC | ((1<<EN)); //make enable pin high
_delay_ms(1);
PORTC = PORTC & (~(1<<EN)); //make enable pin low
}
void LCD_WRT( char *string)
{
while(*string)
DATA_WRT(*string++);//will write the strings
}
int main(void)
{
//setting the display of the lcd

unsigned char CMD[]={0x38,0x01,0x0f,0x06,0x80},TEMP1,i;
DDRB=0XFF; //make PORTB as output
DDRC = 0xFF;//(1<<RS)|(1<<EN); //make PORTC as output
_delay_ms(10); //provide the delay of 10ms
for(i=0;i<5;i++)
{
TEMP1=CMD[i]; //it will place the command in cmd array
CMD_WRT(TEMP1); //it will write all the cmd that is in the cmd array
}
while(1)
{
CMD_WRT(0X01); //clear display
CMD_WRT(0X80); // blink the cursor in 1st row
LCD_WRT(" --RDL--");//display RDL in lcd
CMD_WRT(0XC0); //to use 2nd row of lcd
LCD_WRT(" LCD_DISPLAY"); //display LCD_DISPLAY in lcd
_delay_ms(1000); //delay of 1sec
}
return 0;
}

3. PULSE WIDTH MODULATION:
Program:
// program to change brightness of an LED
// demonstration of PWM
#include <avr/io.h>
// initialize PWM
void pwm_init()
{
// initialize timer0 in PWM mode
TCCR0 |= (1<<WGM00)|(1<<COM01)|(1<<WGM01)|(1<<CS00);
// make sure to make OC0 pin (pin PB3 for atmega32) as output pin
DDRB |= (1<<PB3);
}
void main()
{
uint8_t brightness;
// initialize timer0 in PWM mode
pwm_init();
// run forever
while(1)
{
// increasing brightness
for (brightness = 0; brightness < 255; ++brightness)
{

// set the brightness as duty cycle
OCR0 = brightness;
// delay so as to make the user "see" the change in brightness
_delay_ms(10);
}
// decreasing brightness
for (brightness = 255; brightness > 0; --brightness)
{
// set the brightness as duty cycle
OCR0 = brightness;
// delay so as to make the user "see" the change in brightness
_delay_ms(10);
}
// repeat this forever
}
}

4. ADC :
Program:
#include <avr/io.h>
#include <string.h>
//#include <iom16.h>
//#define LCD_PORT PORTB
#define RS PC0 // connect register select pin to PC0
#define EN PC1 // connect enable pin to PC1
#define LTHRES 500 //setting the threshold valve
#define RTHRES 500
#include <stdlib.h>
void CMD_WRT(unsigned char val)
{
PORTB=val; // initializing PORTB as input and passing valve onto it
PORTC = PORTC & (~(1<<RS));//make RS pin low
_delay_ms(1);
PORTC = PORTC | ((1<<EN));// make EN pin high
_delay_ms(1);
PORTC = PORTC & (~(1<<EN));// make EN pin low
}

void DATA_WRT(unsigned char ch)
{
PORTB = ch; //initializing PORTB as input and passing CMD onto it
PORTC = PORTC | ((1<<RS)); // make RS pin high
_delay_ms(1);
PORTC = PORTC | ((1<<EN));//make EN pin high
_delay_ms(1);
PORTC = PORTC & (~(1<<EN));// make EN pin low
}
void LCD_WRT( char *string)
{
while(*string)
DATA_WRT(*string++);
}
// initialize adc
void adc_init()
{
// AREF = AVcc
ADMUX = (1<<REFS0); //initialize admux
// ADC Enable and prescaler of 128
// 16000000/128 = 125000
ADCSRA = (1<<ADEN)|(1<<ADPS2)|(1<<ADPS1)|(1<<ADPS0);
} //ADEN means ADC enabled
// read adc value
int adc_read(char ch)

{
// select the corresponding channel 0~7
// ANDing with '7' will always keep the value
// of 'ch' between 0 and 7
ch &= 0b00000111; // AND operation with 7
ADMUX = (ADMUX & 0xF8)|ch; // clears the bottom 3 bits
before ORing
// start single conversion
// write '1' to ADSC
ADCSRA |= (1<<ADSC);
// wait for conversion to complete
// ADSC becomes '0' again
// till then, run loop continuously
while(ADCSRA & (1<<ADSC));
return (ADC);
}
int main(void)
{
uint16_t adc_result0;//, adc_result1;
char int_buffer[10]; //creating array of 10
unsigned char CMD[]={0x38,0x01,0x0f,0x06,0x80},TEMP1,i;
DDRB=0XFF;//set port b as output
DDRC = 0xFF;//(1<<RS)|(1<<EN);
_delay_ms(10);
for(i=0;i<5;i++)
{

TEMP1=CMD[i]; //for each one cycle each command will be placed in
that cmd array
CMD_WRT(TEMP1);
}
adc_init();
while(1)
{
//adc_result0 = adc_read(0); // read adc value at PA0
adc_result0 = adc_read(1);
itoa(adc_result0, int_buffer,10);
CMD_WRT(0X01); //clear display
CMD_WRT(0X80); // cursor on first line
LCD_WRT(" --RDL--"); //display RDL
CMD_WRT(0XC0); //cursor on next line
LCD_WRT(int_buffer);
_delay_ms(1000);
//TODO:: Please write your application code
}
return 0;
}

5. KEYPAD:
Block diagram:

Program:
#include<avr/io.h>
#include <avr/keypad.h> // to initialize the keypad
#define F_CPU 1000000UL
#include <util/delay.h> //header to use delay function
#define KEYPAD_PORT PORTC // connecting keypad to port c
#define KEYPAD_PIN PINC //initializing pins for keypad
#define LCD_DATA_PORT PORTB
#define LCD_CONT_PORT PORTD
#define LCD_RS PD0
#define LCD_RW PD1
#define LCD_EN PD2
#include <lcd.h> //header to initialize LCD commands
void main(void)
{
DDRB=0xFF; //make PORTB as output
DDRD=0X07; //make PORTD pin 0, 1, 2 as output
DDRB=0X0F;
PORTC=0xFF; //make PORTC as output
unsigned char keypad_valve;
lcd_init();
while(1)
{
lcd_command_write(0x08); //display off cursor off
lcd_string_write("PRESS ANY KEY");
lcd_command_write(0xc0);//2nd line display
keypad_valve=read_keypad();

if(keypad_valve!=0xFF)
{
lcd_number_write(keypad_valve,10);//if key is pressed corresponding
valve will be displayed
lcd_data_write(' ');
}
else
;
_delay_ms(300);
}
}

SERIAL COMMUNICATION:
What is the USART?
The vast majority of devices in the current AVR family lineup contain a
USART hardware subsystem. The USART hardware allows the AVR to
transmit and receive data serially to and from other devices - such as a
computer or another AVR.
The USART transmission system differs to most other digital busses in that
it does not utilize a separate pin for the serial clock. An agreed clock rate is
preset into both devices, which is then used to sample the Rx/Tx lines at
regular intervals. Because of this, the USART requires only three wires for
bi-directional communication (Rx, Tx and GND).
Setting up the Hardware
• Connect your USART to a computer via the Com port.
• You need to first identify which pins of your AVR(ATmega 16) are
responsible for serial communication.
• For ATmega 16 Pin 14 and Pin 15 are used for receiving and
transmission.
• Connect tx pin of usart to rx pin of ATmega 16 and rx pin of usart to
the tx pin of the ATmega 16 .
• Now to see the transmitted word back in pc you need to use
HyperTerminal (it’s a free software you need to download it)
• set the Baud rate in the HyperTerminal

Setting up HyperTerminal
1. open the HyperTerminal
2. Add name here I have added serial

3. Select your com port which you are using and press ok (to check
the com port go to device manger and check in which com port is the usart connected)
4. select the baud rate that you have set or just click Restore
default it will set the default valve and press ok

5. serial HyperTerminal will get open

Initializing the USART
First off, you need to enable both the USART's transmission and
reception circuitry. For the MEGA16, these are bits named RXEN and TXEN, and
they are located in the control register UCSRB. When set, these two bits turn on
the serial buffers to allow for serial communications
Code:
int main (void)
{
UCSRB = (1 << RXEN) | (1 << TXEN); // Turn on the transmission and reception circuitry
}
Next, we need to tell the AVR what type of serial format we're using.
Looking again at the MEGA16 datasheet, we can see that the bits responsible for
the serial format are named UCSZ0 to UCSZ2, and are located in the USART
control register C named UCSRC.
Code:
UCSRC = (1 << URSEL) | (1 << UCSZ0) | (1 << UCSZ1); // Use 8-bit character sizes - URSEL bit
set to select the UCRSC register
The last thing to set for basic serial communications is the baud rate
register. The baud rate register is 16-bit, split into two 8-bit registers as is the case
with all 16-bit registers in the AVR device family. For this the baud valve need to
be found for that we have a formula
BaudValue = (((F_CPU / (USART_BAUDRATE * 16))) - 1)
Where F_CPU is your AVR's system clock frequency (in Hz), and USART_BAUDRATE is the desired
communication baud rate.
Given my example project using a system clock of 7372800Hz and a baud rate of 9600, our formula
gives:

BaudValue = (((F_CPU / (USART_BAUDRATE * 16UL))) - 1) BaudValue = (7372800 / (9600 * 16) - 1)
BaudValue = (7372800 / 153600 - 1)
BaudValue = (48 - 1)
BaudValue = 47
This avoids "magic numbers" (unexplained constants) in our source code,
and makes changing the baud rate later on very easy - just change the
BAUD_RATE macro value. Now, we need to load this into the baud rate registers,
named UBRRH (for the high byte) and UBRRL (for the low byte). This is simple
via a simple bit shift to grab the upper eight bits of the BAUD_PRESCALE
constant:
UBRRH = (BAUD_PRESCALE >> 8); // Load upper 8-bits of the baud rate value into the high byte
of the UBRR register
UBRRL = BAUD_PRESCALE; // Load lower 8-bits of the baud rate value into the low byte of the
UBRR register
Sending and receiving data
We do this by the special register named UDR - short for "USART I/O
Data Register”. On the MEGA16, the Transmission Complete flag is located in the
control register UCSRA, and it is named TXC. Using this information we can
construct a simple wait loop which will prevent data from being written to the
UDR register until the current transmission is complete.
UDR = ByteToSend; // Send out the byte value in the variable "ByteToSend"
while ((UCSRA & (1 << TXC)) == 0) {}; // Do nothing until transmission complete flag set
However this is non-optimal. We spend time waiting after each byte which
could be better spent performing other tasks - better to check before a transmission
to see if the UDR register is ready for data. We can do this by checking the
USART Data Register Empty flag instead (called UDRE), also located in the
UCSRA control register of the MEGA16

while ((UCSRA & (1 << UDRE)) == 0) {}; // Do nothing until UDR is ready for more data to be
written to it
UDR = ByteToSend; // Send out the byte value in the variable "ByteToSend"
Now we can move on to receiving data. we need to check to see if we have
received a byte.
To do this, we can check the USART Receive Complete (RXC) flag to see if it is
set. Again, this is located in the UCSRA control register of the MEGA16:
while ((UCSRA & (1 << RXC)) == 0) {}; // Do nothing until data have been received and is ready
to be read from UDR
ReceivedByte = UDR; // Fetch the received byte value into the variable "ReceivedByte"
CODE:
#include <avr/io.h>
#include <avr/delay.h>
#define F_CPU ((unsigned long)8000000)
#define F_OSC 8000000// for 8mhz
#define USART_BAUDRATE 9600
#define BAUD_PRESCALE (((F_CPU / ( USART_BAUDRATE * 16UL))) - 1)
unsigned char
int main (void)

{
char ReceivedByte;
UCSRB = (1 << RXEN) | (1 << TXEN); // Turn on the transmission and reception
circuitry
UCSRC = (1 << URSEL) | (1 << UCSZ0) | (1 << UCSZ1); // Use 8-bit character sizes
UBRRH = (BAUD_PRESCALE >> 8); // Load upper 8-bits of the baud rate value into the
high byte of the UBRR register
UBRRL = BAUD_PRESCALE; // Load lower 8-bits of the baud rate value into the low byte
of the UBRR register
for (;;) // Loop forever
{
while ((UCSRA & (1 << RXC)) == 0) {}; // Do nothing until data have been
received and is ready to be read from UDR
ReceivedByte = UDR; // Fetch the received byte value into the variable
"ByteReceived"
//_delay_ms(1000);
while ((UCSRA & (1 << UDRE)) == 0) {}; // Do nothing until UDR is ready for
more data to be written to it
UDR = ReceivedByte; // Echo back the received byte back to the computer
}
}

Related Products:
Atmega 16/32/64 Project Board Atmega 16/32/64 Development Board-USB
Product Code: G89S52 Product Code: ATM-U
Atmega Programmer-USB ISP Atmel Programmer
Product Code: AVR Product Code: UAB

01010101010101010100101010101010101010101010101010101010101010101010101010101010101
01010101010101010100101010101010101010101010101010101010101010101010101010101010101
01010101010101010100101010101010101010101010101010101010101010101010101010101010101
01010101010101010100101010101010101010101010101010101010101010101010101010101010101
01010101010101010100101010101010101010101010101010101010101010101010101010101010101
01010101010101010100101010101010101010101010101010101010101010101010101010101010101
01010101010101010100101010101010101010101010101010101010101010101010101010101010101
01010101010101010100101010101010101010101010101010101010101010101010101010101010101
01010101010101010100101010101010101010101010101010101010101010101010101010101010101
01010101010101010100101010101010101010101010101010101010101010101010101010101010101
01010101010101010100101010101010101010101010101010101010101010101010101010101010101
01010101010101010100101010101010101010101010101010101010101010101010101010101010101
01010101010101010100101010101010101010101010101010101010101010101010101010101010101
01010101010101010100101010101010101010101010101010101010101010101010101010101010101
01010101010101010100101010101010101010101010101010101010101010101010101010101010101
01010101010101010100101010101010101010101010101010101010101010101010101010101010101
01010101010101010100101010101010101010101010101010101010101010101010101010101010101
01010101010101010100101010101010101010101010101010101010101010101010101010101010101
01010101010101010100101010101010101010101010101010101010101010101010101010101010101
01010101010101010100101010101010101010101010101010101010101010101010101010101010101
01010101010101010100101010101010101010101010101010101010101010101010101010101010101
01010101010101010100101010101010101010101010101010101010101010101010101010101010101
01010101010101010100101010101010101010101010101010101010101010101010101010101010101
01010101010101010100101010101010101010101010101010101010101010101010101010101010101
01010101010101010100101010101010101010101010101010101010101010101010101010101010101
01010101010101010100101010101010101010101010101010101010101010101010101010101010101
01010101010101010100101010101010101010101010101010101010101010101010101010101010101
01010101010101010100101010101010101010101010101010101010101010101010101010101010101
01010101010101010100101010101010101010101010101010101010101010101010101010101010101
01010101010101010100101010101010101010101010101010101010101010101010101010101010101
01010101010101010100101010101010101010101010101010101010101010101010101010101010101
01010101010101010100101010101010101010101010101010101010101010101010101010101010101
01010101010101010100101010101010101010101010101010101010101010101010101010101010101
01010101010101010100101010101010101010101010101010101010101010101010101010101010101
01010101010101010100101010101010101010101010101010101010101010101010101010101010101
01010101010101010100101010101010101010101010101010101010101010101010101010101010101
01010101010101010100101010101010101010101010101010101010101010101010101010101010101
01010101010101010100101010101010101010101010101010101010101010101010101010101010101
01010101010101010100101010101010101010101010101010101010101010101010101010101010101
01010101010101010100101010101010101010101010101010101010101010101010101010101010101
01010101010101010100101010101010101010101010101010101010101010101010101010101010101
01010101010101010100101010101010101010101010101010101010101010101010101010101010101
01010101010101010100101010101010101010101010101010101010101010101010101010101010101
01010101010101010100101010101010101010101010101010101010101010101010101010101010101
01010101010101010100101010101010101010101010101010101010101010101010101010101010101
01010101010101010100101010101010101010101010101010101010101010101010101010101010101
01010101010101010100101010101010101010101010101010101010101010101010101010101010101
01010101010101010100101010101010101010101010101010101010101010101010101010101010101
01010101010101010100101010101010101010101010101010101010101010101010101010101010101
01010101010101010100101010101010101010101010101010101010101010101010101010101010101
01010101010101010100101010101010101010101010101010101010101010101010101010101010101
01010101010101010100101010101010101010101010101010101010101010101010101010101010101
01010101010101010100101010101010101010101010101010101010101010101010101010101010101
01010101010101010100101010101010101010101010101010101010101010101010101010101010101
01010101010101010100101010101010101010101010101010101010101010101010101010101010101
Research
Design Lab
www.researchdesignlab.com
Email: sales@researchdesignlab.com I www.researchdesignlab.com
An ISO 9001- 2008 Certified Company
Atmega Development Board

RESEARCH DESIGN LABS | VOLUME 1, ISSUE 1 WWW.RESEARCHDESIGNLAB.COM
1. Power supply, 5V-12V
2. 40 pin ZIF socket for IC mount.
3. ISP connector*
4. Reset
5. Node connector
6. 4x1 7 segment display
7. 26 pin raspberry connector
8. Arduino Shield footprint
9. ULN 2803 driver
10. I2C bus
11. SPI bus
12. XBEE footprint/XBEE Adaptor module
13. FT232 breakout board connector
14. DC 3.3V connectors
15. DB-9 female connector
16. 8x1 LED's
17. 8 way DIP switch
18. RTC Module
19. EEPROM
20. 2x5x2 jumper node.
21. DC 5V connectors
22. Analog to Digital output
23. 4x1 keypad
24. 16x2 LCD connectors
25. Node connector
26. 4x4 Matrix Keypad
28. Power ON switch

All digital circuits require regulated power supply. Here is
a simple power supply circuit diagram used on this board.
You can use AC or DC source (12V) which converts into
regulated 5V which is required for driving the
development board circuit.
Power supply, 5V-12V
Select the IC's from the given list and mount on the ZIF socket. ZIF socket pin maps out PORT1
PORT2 PORT3 PORT4 for easy making connections for the rest of the circuit. Port 1 is enabled with
pull up circuit and also connected ISP for easy on board Programming.
1. 40 pin ZIF socket for IC mount & ISP connector*

2. Reset
Resets your microcontroller Node connector is an additional on board
connection extender or 1 connection
IN and 1 connection OUT
One seven segment digit consist of 7+1 LEDs which are arranged in a specific formation which
can be used to represent digits from 0 to 9 and even some letters. One additional LED is used for
marking the decimal dot, in case you want to write a decimal point in the desired segment.
3. Node connector
4. 4 digit 7 segment display

26 Pin Raspberry Pi connector is an easy way
for making connections with Raspberry Pi
along with this development board.
Arduino Shield footprint is provided in the
board to mount different types of Arduino
compatible shields on this development board.
IC ULN2803 consists of octal high voltage, high current darlington transistor arrays. The eight NPN
Darlington connected transistors in this family of arrays are ideally suited for interfacing between
low logic level digital circuitry (such as TTL, CMOS or PMOS/NMOS) and the higher
current/voltage requirements of lamps, relays, printer hammers or other similar loads for a
broad range of computer, industrial, and consumer applications.
5. 26 pin Raspberry Pi connector 6. Arduino Shield footprint
7. ULN 2803 driver

• Eight Darlingtons with Common Emitter.
• Open–collector outputs.
• Free wheeling clamp diodes for
transient suppression.
• Output Current to 500 mA.
• Output Voltage to 50 V.
• Inputs pinned opposite outputs to
simplify board layout.
The ULN 2803 IC consists of eight NPN
Darlington connected transistors (often
called a Darlington pair). Darlington pair
consists of two bipolar transistors such
that the current amplified by the first is
amplified further by the second to get a
high current gain β or hFE. The figure
shown below is one of the eight Darlington
pairs of ULN 2803 IC.
Now 2 cases arise:-
Case 1: When IN is 0 volts.
Q1 and Q2 both will not conduct as there is
no base current provided to them. Thus,
nothing will appear at the output (OUT).
Case 2: When IN is 5 volts.
Input current will increase and both transistors Q1 and Q2 will begin to conduct. Now, input
current of Q2 is combination of input current and emitter current of Q1, so Q2 will conduct more
than Q1 resulting in higher current gain which is very much required to meet the higher current
requirements of devices like motors, relays etc. Output current flows through Q2 providing a
path (sink) to ground for the external circuit that the output is applied to. Thus, when a 5V input
is applied to any of the input pins (1 to 8), output voltage at corresponding output pin (11 to 18)
drops down to zero providing GND for the external circuit. Thus, the external circuit gets
grounded at one end while it is provided +Vcc at its other end. So, the circuit gets completed and
starts operating.
Features Working

One IC that wants to communicate to another must: (Protocol)
1) Wait until it sees no activity on the I2C bus. SDAand SCLare both high. The bus is 'free'.
2) Put a message on the bus that says 'its mine' - I have STARTED to use the bus. All other ICs then
LISTEN to the bus data to see whether they might be the one who will be called up
(addressed).
3) Provide on the CLOCK (SCL) wire a clock signal. It will be used by all the ICs as the reference
time at which each bit of DATA on the data (SDA) wire will be correct (valid) and can be used.
The data on the data wire (SDA) must be valid at the time the clock wire (SCL) switches from
'low' to 'high' voltage.
4) Put out in serial form the unique binary 'address'(name) of the IC that it wants to
communicate with.
5) Put a message (one bit) on the bus telling whether it wants to SEND or RECEIVE data from the
other chip. (The read/write wire is gone!)
6) Ask the other IC toACKNOWLEDGE (using one bit) that it recognized its address and is ready to
communicate.
7) After the other IC acknowledges all is OK, data can be transferred.
8) The first IC sends or receives as many 8-bit words of data as it wants. After every 8-bit data
word the sending IC expects the receiving IC to acknowledge the transfer is going OK.
9) When all the data is finished the first chip must free up the bus and it does that by a special
message called 'STOP'. It is just one bit of information transferred by a special 'wiggling' of the
SDA/SCLwires of the bus.
8. I2C bus

Serial to Peripheral Interface (SPI) is a hardware/firmware communications protocol developed
by Motorola and later adopted by others in the industry. Microwire of National Semiconductor is
same as SPI. Sometimes SPI is also called a "four wire" serial bus.
The Serial Peripheral Interface or SPI-bus is a simple 4-wire serial communications interface used
by many microprocessor/microcontroller peripheral chips that enables the controllers and
peripheral devices to communicate each other. Even though it is developed primarily for the
communication between host processor and peripherals, a connection of two processors via SPI is
just as well possible.
The SPI bus, which operates at full duplex (means, signals carrying data can go in both directions
simultaneously), is a synchronous type data link setup with a Master / Slave interface and can
support up to 1 megabaud or 10Mbps of speed. Both single-master and multi-master protocols are
possible in SPI. But the multi-master bus is rarely used and look awkward, and are usually limited
to a single slave.
The SPI Bus is usually used only on the PCB. There are many facts, which prevent us from using it
outside the PCB area. The SPI Bus was designed to transfer data between various IC chips, at very
high speeds. Due to this high-speed aspect, the bus lines cannot be too long, because their
reactance increases too much, and the Bus becomes unusable. However, its possible to use the SPI
Bus outside the PCB at low speeds, but this is not quite practical.
The peripherals can be a Real Time Clocks, converters like ADC and DAC, memory modules like
EEPROM and FLASH, sensors like temperature sensors and pressure sensors, or some other devices
like signal-mixer, potentiometer, LCD controller, UART, CAN controller, USB controller and
amplifier.
9. SPI bus

All XBeeZNet 2.5 modules can be identified by their unique 64-bit addresses or a user-
configurableASCII string identifier The 64-bit address of a module can be read using the SH and SL
commands. TheASCII string identifier is configured using the NI command.
To transmit using device addressing, only the destination address must be configured. The
destination address can be specified using either the destination device's 64-bit address or its NI-
string. The XBee modules also support coordinator and broadcast addressing modes. Device
addressing in the AT firmware is configured using the DL, DH, or DN commands. In the API
firmware, the ZigBee Transmit Request API frame (0x10) can be used to specify destination
addresses.
To address a node by its 64-bit address, the destination address must be set to match the 64-bit
address of the remote. In the AT firmware, the DH and DL commands set the destination 64-bit
address. In the API firmware, the destination 64-bit address is set in the ZigBee Transmit Request
frame. ZigBee end devices rely on a parent (router or coordinator) to remain awake and receive
any data packets destined for the end device. When the end device wakes from sleep, it sends a
transmission (poll request) to its parent asking if the parent has received any RF data destined for
the end device. The parent, upon receipt of the poll request, will send an RF response and the
buffered data (if present). If the parent has no data for the end device, the end device may return
to sleep, depending on its sleep mode configuration settings. The following figure demonstrates
how the end device uses polling to receive RF data through its parent.
10. XBEE footprint/ XBEE Adaptor module

A s t a n d a r d F T 2 3 2
breakout board from
researchdesignlab.com
could be used to interface
on these connectors,
whose other end is
connected to a USB.
These connectors provide on board
3.3V DC connections.
RS-232 is a standard communication protocol for linking computer and its peripheral devices to
allow serial data exchange. In simple terms RS232 defines the voltage for the path used for data
exchange between the devices. It specifies common voltage and signal level, common pin wire
configuration and minimum, amount of control signals.
11. Ft232 breakout
board connector
12. DC 3.3V connectors
13. DB-9 female connector

LED's are used to indicate
something, whether any pin is high
or indicating the output for many
purposes like indicating I/O status
or program debugging running
state. We have 8 led outputs on
board which can be used by the
programmer as per the requirement
for testing and development.
DIP switches are an alternative to jumper blocks. Their main advantages are that they are
quicker to change and there are no parts on lose.
The DS1307 Serial Real Time Clock is a low power, full BCD clock/calendar plus 56 bytes of
nonvolatile SRAM. Address and data are transferred serially via a 2-wire bi-directional bus. The
clock/calendar provides seconds, minutes, hours, day, date, month, and year information. The
end of the month date is automatically adjusted for months with less than 31 days, including
corrections for leap year. The clock operates in either the 24-hour or 12-hour format with AM/PM
indicator. The DS1307 has a built-in power sense circuit which detects power failures and
automatically switches to the battery supply.
14. 8x1 LED's
15. 8 way DIP switch
16. RTC Module

The DS1307 operates as a slave device on the serial bus. Access is obtained by implementing a
START condition and providing a device identification code followed by a register address.
Subsequent registers can be accessed sequentially until a STOP condition is executed. When VCC
falls below 1.25 x VBAT the device terminates an access in progress and resets the device address
counter. Inputs to the device will not be recognized at this time to prevent erroneous data from
being written to the device from an out of tolerance system. When VCC falls below VBAT the
device switches into a low current battery backup mode. Upon power up, the device switches
from battery to VCC when VCC is greater than VBAT +0.2V and recognizes inputs.
Features:
1. 56 byte nonvolatile RAM for data storage
2. 2-wire serial interface
3. Programmable square wave output signal
4. Automatic power-fail detect and switch circuitry
5. Consumes less than 500 nA in battery backup mode with oscillator running
6. Optional industrial temperature range -40°C to +85°C
7. Available in 8-pin DIP or SOIC
8. Recognized by Underwriters Laboratory
PIN DESCRIPTION
1. VCC - Primary Power Supply
2. X1, X2 - 32.768 kHz Crystal
Connection
3. VBAT - +3V Battery Input
4. GND - Ground
5. SDA - Serial Data
6. SCL - Serial Clock
7. SQW/OUT - Square
wave/Output Driver
Operation

IC, EEPROM I2C 4K, 24C04, DIP8
Memory Size: 4Kbit
Memory Configuration: 512 x 8
Interface Type: I2C, Serial
Clock Frequency: 400kHz
Supply Voltage Range: 2.5V to 5.5V
Memory Case Style: DIP
No. of Pins: 8
Operating Temperature Range: -40°C to
+85°C
SVHC: No SVHC (19-Dec-2011)
Base Number: 24
Device Marking: M24C04
IC Generic Number: 24C04
Interface: I2C
Interface Type: Serial, I2C
Logic Function Number: 24C04
Memory Configuration: 512 x 8
Memory Size: 4Kbit
Memory Type: EEPROM
Memory Voltage Vcc: 2.5V
Operating Temperature Max: +85°C
Operating Temperature Min: -40°C
Package / Case: DIP
Supply Voltage Max: 5.5V
Supply Voltage Min: 2.5V
Termination Type: Through Hole
Voltage Vcc: 2.5V
18. 2x5x2 jumper node
17. EEPROM
Node connector is an additional on board connection
extender or 1 connection IN and 1 connection OUT

These connectors provide on board 5V
DC connections.
The Potentiometer Option allows the user to adjust the voltage reference by rotating a
potentiometers dial. Turning the potentiometer changes the voltage reference making it easier
to adjust the motor speed and also to set the duty cycle for PWM values (via programming).
Switches are mainly used to
switch the controls of a
module. We have four
switches on board which can
be used by the programmer
as per the requirement for
testing and development.
20. Potentiometer
21.4x1 keypad

LCD screen consists of two lines with 16 characters each. Each character consists of 5x7 dot
matrix. Contrast on display depends on the power supply voltage and whether messages are
displayed in one or two lines. For that reason, variable voltage 0-Vdd is applied on pin marked as
Vee. Trimmer potentiometer is usually used for that purpose. Some versions of displays have built
in backlight (blue or green diodes). When used during operating, a resistor for current limitation
should be used (like with any LE diode). LCD Connection Depending on how many lines are used for
connection to the microcontroller, there are 8-bit and 4-bit LCD modes. The appropriate mode is
determined at the beginning of the process in a phase called “initialization”. In the first case, the
data are transferred through outputs D0-D7 as it has been already explained. In case of 4-bit LED
mode, for the sake of saving valuable I/O pins of the microcontroller, there are only 4 higher bits
(D4-D7) used for communication, while other may be left unconnected.
Consequently, each data is sent to LCD in two steps: four higher bits are sent first (that normally
would be sent through lines D4-D7), four lower bits are sent afterwards. With the help of
initialization, LCD will correctly connect and interpret each data received. Besides, with regards
to the fact that data are rarely read from LCD (data mainly are transferred from microcontroller
to LCD) one more I/O pin may be saved by simple connecting R/W pin to the Ground. Such saving
has its price. Even though message displaying will be normally performed, it will not be possible
to read from busy flag since it is not possible to read from display.
Features:
1. Can display 224 different symbols.
2. Low power consumption.
3. 5x7 dot matrix format.
4. Powerful command set and user produced characters.
Fig: Circuit connections of LCD
22. 16x2 LCD connectors
10k

1. Gnd:- Power supply ground
2. VCC:-+5v Power supply input
3. RS:- Register Select
Node connector is an additional on board connection extender or 1 connection IN and 1
connection OUT
4. R/W:- Read/Write pin
5. En:-Enable pin
6. D0-D7:- Data lines
Pin Description
23. Node connector

In a 4x4 matrix keypad eight Input/Output ports are used for interfacing with any
microcontrollers. Rows are connected to Peripheral Input/Output (PIO) pins configured as
output. Columns are connected to PIO pins configured as input with interrupts.
FEATURES
1. Contact debouncing.
2. Easy to interface.
3. Interfaces to any microcontroller or microprocessor.
4. Data valid output signal for interrupt activation.
PIN DETAILS
pin 1-4: R0-R3:- Rows
pin 5-8: C0-C3:- Columns
24. 4x4 Matrix Keypad
These connectors provide on
board 12V DC connections.
Programming Codes:
• LED BLINK
http://researchdesignlab.com/8051-i/o-code
• LCD
http://researchdesignlab.com/8051-lcd-code
• KEYPAD
http://researchdesignlab.com/8051-keypad-code
• UART
http://researchdesignlab.com/8051-uart-code
• RTC
http://researchdesignlab.com/8051-rtc-code
• EEPROM
http://researchdesignlab.com/8051-eeprom-code
• ADC
http://researchdesignlab.com/8051-adc-code.html
• 7 Segment Display
http://researchdesignlab.com/7-segment-atmel-code.html

Avr book

More Related Content

What's hot (20)

Similar to Avr book (20)

More from Rajan Gautam (12)

Recently uploaded (20)

Avr book