![International Journal of Wireless & Mobile Networks (IJWMN) Vol. 5, No. 5, October 2013
Spatial multiplexing is a transmission technique in MIMO wireless communication system to
transmit independent and separately encoded data signals, called as streams, from each of the
multiple transmit antennas. Therefore, the space dimension is reused or multiplexed more than
one time. If the transmitter and receiver has Nt and Nr antennas respectively, the maximum spatial
multiplexing order (the number of streams) is
NS =min (Nt ,Nr)
(1)
The general concept of spatial multiplexing can be understood using MIMO antenna
configuration. In spatial multiplexing, a high data rate signal is divided into multiple low rate data
streams and each stream is transmitted from a different transmitting antenna. These signals arrive
at the receiver antenna array with different spatial signatures, the receiver can separate these
streams into parallel channels thus improving the capacity. Thus spatial multiplexing is a very
powerful technique for increasing channel capacity at higher SNR values. The maximum number
of spatial streams is limited by the lesser number of antennas at the transmitter or receiver side.
Spatial multiplexing can be used with or without transmit channel knowledge.
Figure 2.Spatial Multiplexing Concept
MIMO spatial multiplexing achieves high throughput by utilizing the multiple paths and
effectively using them as additional channels to carry data such that receiver receives multiple
data at the same time. The tenet in spatial multiplexing is to transmit different symbols from each
antenna and the receiver discriminates these symbols by taking advantage of the fact that, due to
spatial selectivity, each transmit antenna has a different spatial signature at the receiver . This
allows an increased number of information symbols per MIMO symbol. In any case for MIMO
spatial multiplexing, the number of receiving antennas must be equal to or greater than the
number of transmit antennas such that data can be transmitted over different antennas. Therefore
the space dimension is reused or multiplexed more than one time. The data streams can be
separated by equalizers if the fading processes of the spatial channels are nearly independent.
Spatial multiplexing requires no bandwidth expansion and provides additional data bandwidth in
multipath radio scenarios [2].
2. MIMO SYSTEM
In MIMO system we use multiple antennas at transmitter and receiver side, they are extension of
developments in antenna array communication. There are three categories of MIMO techniques.
The first aims to improve the reliability by decreasing the fading through multiple spatial paths.
Such technique includes STBC and STTC. The second class uses a layered approach to increase
capacity. One popular example of such a system is V-BLAST suggested by Foschini et al. [2].
86](https://image.slidesharecdn.com/beranalysisof2x2mimospatialmultiplexingunderawgnandricianchannelsfordifferentmodulationstechniques-131111222751-phpapp02/85/Ber-analysis-of-2x2-mimo-spatial-multiplexing-under-awgn-and-rician-channels-for-different-modulations-techniques-2-320.jpg)
![International Journal of Wireless & Mobile Networks (IJWMN) Vol. 5, No. 5, October 2013
Finally, the third type exploits the knowledge of channel at the transmitter. It decomposes the
channel coefficient matrix using SVD and uses these decomposed unitary matrices as pre- and
post-filters at the transmitter and the receiver to achieve near capacity [3].
2.1. Benefits of MIMO system
MIMO channels provide a number of advantages over conventional Single Input Single Output
(SISO) channels such as the array gain, the diversity gain, and the multiplexing gain. While the
array and diversity gains are not exclusive of MIMO channels and also exist in single-input
multiple-output (SIMO) and multiple-input single-output (MISO) channels, the multiplexing gain
is a unique characteristic of MIMO channels. These gains are described in brief below:
2.2.1 Array Gain
Array gain is the average increase in the SNR at the receiver that arises from the coherent
combining effect of multiple antennas at the receiver or transmitter or both. Basically, multiple
antenna systems require perfect channel knowledge either at the transmitter or receiver or both to
achieve this array gain.
2.2.2 Spatial Diversity Gain
Multipath fading is a significant problem in communications. In a fading channel, signal
experiences fade (i.e they fluctuate in their strength) and we get faded signal at the receiver end.
This gives rise to high BER. We resort to diversity to combat fading. This involves providing
replicas of the transmitted signal over time, frequency, or space.
.
2.2.3 Spatial Multiplexing Gain
Spatial multiplexing offers a linear (in the number of transmit-receive antenna pairs or min (MR,
MT) increase in the transmission rate for the same bandwidth and with no additional power
expenditure. It is only possible in MIMO channels. Consider the cases of two transmit and two
receive antennas. The stream is split into two half-rate bit streams, modulated and transmitted
simultaneously from both the antennas. The receiver, having complete knowledge of the channel,
recovers these individual bit streams and combines them so as to recover the original bit stream.
Since the receiver has knowledge of the channel it provides receive diversity, but the system has
no transmit diversity since the bit streams are completely different from each other in that they
carry totally different data. Thus spatial multiplexing increases the transmission rates
proportionally with the number of transmit-receive antenna pairs.
2.3 Modulation
Modulation is the process of mapping the digital information to analog form so it can be
transmitted over the channel. Modulation of a signal changes binary bits into an analog
waveform. Modulation can be done by changing the amplitude, phase, and frequency of a
sinusoidal carrier. Every digital communication system has a modulator that performs this task.
Similarly we have a demodulator at the receiver that performs inverse of modulation. There are
several digital modulation techniques used for data transmission.
87](https://image.slidesharecdn.com/beranalysisof2x2mimospatialmultiplexingunderawgnandricianchannelsfordifferentmodulationstechniques-131111222751-phpapp02/85/Ber-analysis-of-2x2-mimo-spatial-multiplexing-under-awgn-and-rician-channels-for-different-modulations-techniques-3-320.jpg)
![International Journal of Wireless & Mobile Networks (IJWMN) Vol. 5, No. 5, October 2013
y(t)=x(t)*h(t)n(t)
(4)
where h(t) is the random channel matrix having Rician distribution and n(t) is the additive white
Gaussian noise.
The Rician distribution is given by:
P(r) =
మ
మ
୰మ (ି ౨ శఽ )
౨
ಚమ
e
IOቀమ ቁ
మ
(5)
for (A 0, r 0)
where A denotes the peak amplitude of the dominant signal and IO[.] is the modified Bessel
function of the first kind and zero-order.
2.5 Detection Techniques
There are numerous detection techniques available with combination of linear and non-linear
detectors. The most common detection techniques are ZF, MMSE and ML detection technique.
The generalized block diagram of MIMO detection technique is shown in Figure 4.
Fig. 4 Block Diagram of system with equalizer
2.5.1 Zero Forcing (ZF) Detection
The ZF is a linear estimation technique, which inverse the frequency response of received signal,
the inverse is taken for the restoration of signal after the channel. The estimation of strongest
transmitted signal is obtained by nulling out the weaker transmit signal. The strongest signal has
been subtracted from received signal and proceeds to decode strong signal from the remaining
transmitted signal. ZF equalizer ignores the additive noise and may significantly amplify noise for
channel.
The basic Zero force equalizer of 2x2 MIMO channel can be modelled by taking received signal
ݕଵ during first slot at receiver antenna as:
yଵ = hଵ,ଵ xଵ hଵ,ଶ xଶ nଵ =ሾhଵ,ଵ
x
hଵ,ଶ ሿ ቂ ଵ ቃ n1
xଶ
(6)
The received signal y2 at the second slot receiver antenna is:
y2= hଶ,ଵ xଵ hଶ,ଶ xଶ nଶୀ ሾhଶ,ଵ
x
hଶ,ଶ ሿ ቂ ଵ ቃ nଶ
xଶ
(7)
89](https://image.slidesharecdn.com/beranalysisof2x2mimospatialmultiplexingunderawgnandricianchannelsfordifferentmodulationstechniques-131111222751-phpapp02/85/Ber-analysis-of-2x2-mimo-spatial-multiplexing-under-awgn-and-rician-channels-for-different-modulations-techniques-5-320.jpg)
![International Journal of Wireless & Mobile Networks (IJWMN) Vol. 5, No. 5, October 2013
Where i=1, 2 in xi is the transmitted symbol and i=1, 2 in hi, j is correlated matrix of fading
channel, with j represented transmitted antenna and i represented receiver antenna, is the noise of
first and second receiver antenna. The ZF equalizer is given by:
ିଵ
W = ൫H ୌ ൯ Hୌ
(8)
Where WZF is equalization matrix and H is a channel matrix. Assuming MR ்ܯand H has full
rank, the result of ZF equalization before quantization is written
ିଵ
as:
y = ൫H ୌ H൯ HH y
(9)
2.5.2. Minimum Mean Square Estimator (MMSE)
Minimum mean square error equalizer minimizes the mean –square error between the output of
the equalizer and the transmitted symbol, which is a stochastic gradient algorithm with low
complexity. Most of the finite tap equalizers are designed to minimize the mean square error
performance metric but MMSE directly minimizes the bit error rate. The channel model for
MMSE is same as ZF [13],[14]. The MMSE equalization is
ଶ
Wୗ = arg ୫୧୬ E୶,୬ ሾฮx െ x ^ ฮ ሿ
ୋ
(10)
Where is WMMSE equalization matrix, H channel correlated matrix and n is channel noise
yୗ = H ୌ (HH ୌ n୭ I୬ )ିଵ y
(11)
3. Results and Discussions
This paper analyzes the Spatial Multiplexing(SM) technique for 2x2 antenna
configuration under different modulation techniques for different fading channels i.e.
AWGN and Rician channels. Results are shown in the term of BER vs SNR plots.
3.1 Using ZF detection
32-PSK modulation with 2x2 MIMO for AWGN and Rician channel with ZF
0
10
AWGN
Rician
-1
10
-2
Bit Error Rate
10
-3
10
-4
10
-5
10
-6
10
-7
10
0
10
20
30
40
50
Average Eb/No,dB
60
70
80
90
Figure 5(a).
90](https://image.slidesharecdn.com/beranalysisof2x2mimospatialmultiplexingunderawgnandricianchannelsfordifferentmodulationstechniques-131111222751-phpapp02/85/Ber-analysis-of-2x2-mimo-spatial-multiplexing-under-awgn-and-rician-channels-for-different-modulations-techniques-6-320.jpg)
![International Journal of Wireless & Mobile Networks (IJWMN) Vol. 5, No. 5, October 2013
REFERENCES
[1]
H. Jiang and P. A. Wilford, "A hierarchical modulation for upgrading digital broadcasting systems,"
IEEE Transaction on Broadcasting, vol. 51, pp. 222-229, June 2005.
[2]
P. W. Wolniansky, G. J. Foschini, G. D. Golden and R. A.Valenzuela, "V-BLAST: an architecture for
realizing very high data rates over the rich- scattering wireless channel," In Proceeding of
International symposium on Signals, Systems Electronics, pp. 259-300, October 1998.
[3]
J. Ha, A. N. Mody, J. H. Sung, J. Barry, S. Mclaughlin and G. L. Stuber, “LDPC coded OFDM with
Alamouti/SVD diversity technique,” IEEE Journal on Wireless Personal Communication, Vol. 23 ,
Issue 1,pp. 183-194,Oct. 2002.
[4]
P. S. Mundra , T. L. Singal and R. Kapur, “The Choice of A Digital Modulation ,Schemes in A
Mobile Radio System”, In proceedings of IEEE Vehicular Technology Conference, Issue 5, pp 1-4,(
Secaucus, NJ)1993.
[5]
P. Liu & I1-Min Kim, “Exact and Closed-Form Error Performance Analysis for Hard MMSE-SIC
Detection in MIMO Systems”, IEEE Transactions on Communication, Vol. 59, no. 9, September
2011.
[6]
P. Sanghoi & L. Kansal,” Analysis of WiMAX Physical Layer Using Spatial Multiplexing Under
Different Fading Channels”, SPIJ, Vol.(6),Issue(3),2012.
[7]
C. Wang & E. K. S. Au, R. D Murch, W. H. Mow & V. Lau,” On the Performance of the MIMO
Zero-Forcing Receiver in the Presence of Channel Estimation Error”, IEEE Transactions on Wireless
Communication, Vol. 6,no.3,2007.
[8]
X. Zhang, Y. Su & G. Tao, “Signal Detection Technology Research of MIMO-OFDM System”, 3rd
International Congress on Image and Signal Processing, pp 3031-3034, 2010.
[9]
I. Ammu & R. Deepa, “Performance Analysis of Decoding Algorithms in multiple antenna systems”,
IEEE, pp 258-262, 2011.
[10] H. B. Voelcker, “Phase-shift keying in fading channels” , In IEEE Proceeding on Electronics and
Communication Engineering, Vol. 107, Issue 31, pp 31-38, 1960.
[11] D. S. Shiu, G. J. Foschini, M. J. Gans, and J. M. Kahn, “Fading correlation and its effect on the
capacity of multi-element antenna systems”, IEEE Transaction on Communication, Vol. 48, pp. 502–
513, 2000.
[12] G. J. Foschini, K. Karakayali, and R. A.Valenzuela, “Coordinating multiple antenna cellular networks
to achieve enormous spectral efficiency,” Communications, IEEE Proceedings, Vol. 153, pp. 548–
555, 2006.
[13] J. S. Thompson, B. Mulgrew and Peter M. Grant, “A comparison of the MMSE detector and its
BLAST versions for MIMO channels”, IET seminar on Communication System from Concept to
Implementation, pp. 1911-1916, 2001.
[14] X. Zhang and Sun-Yuan Kung, “Capacity analysis for parallel and sequential MIMO equalizers”,
IEEE Transaction on Signal processing, Vol. 51, pp. 2989-3002, 2003.
97](https://image.slidesharecdn.com/beranalysisof2x2mimospatialmultiplexingunderawgnandricianchannelsfordifferentmodulationstechniques-131111222751-phpapp02/85/Ber-analysis-of-2x2-mimo-spatial-multiplexing-under-awgn-and-rician-channels-for-different-modulations-techniques-13-320.jpg)
Ber analysis of 2x2 mimo spatial multiplexing under awgn and rician channels for different modulations techniques
- 1. International Journal of Wireless & Mobile Networks (IJWMN) Vol. 5, No. 5, October 2013 BER ANALYSIS OF 2X2 MIMO SPATIAL MULTIPLEXING UNDER AWGN AND RICIAN CHANNELS FOR DIFFERENT MODULATIONS TECHNIQUES Anuj Vadhera and Lavish Kansal Lovely Professional University, Phagwara, Punjab, India ABSTRACT Multiple-input–multiple-output (MIMO) wireless systems use multiple antennas at transmitting and receiving end to offer improved capacity and data rate over single antenna systems in multipath channels. In this paper we have investigated the Spatial Multiplexing technique of MIMO systems. Here different fading channels like AWGN and Rician are used for analysis purpose. Moreover we analyzed the technique using high level modulations (i.e. M-PSK for different values of M). Detection algorithms used are ZeroForcing and Minimum mean square estimator. Performance is analyzed in terms of BER (bit error rate) vs. SNR (signal to noise ratio). KEYWORDS Spatial Multiplexing (SM), Additive White Gaussian Noise (AWGN), Multiple Input Multiple Output (MIMO), Bit error rate (BER). 1. INTRODUCTION Multiple antenna systems (MIMO) attract significant attention due to their ability of resolving the bottleneck of traffic capacity in wireless networks. MIMO systems are illustrated in Figure 1. The idea behind MIMO is that the signals on the transmitting (Tx) antennas and the receiving (Rx) antennas are combined in such a way that the quality (bit-error rate or BER) or the data rate (bits/sec) of the communication for each MIMO user will be improved. Such an advantage can be used to increase the network’s quality of service. In this paper, we focus on the Spatial Multiplexing technique of MIMO systems. Figure 1.Diagram of MIMO wireless transmission system . Transmitter and receiver are equipped with multiple antennas DOI : 10.5121/ijwmn.2013.5506 85
- 2. International Journal of Wireless & Mobile Networks (IJWMN) Vol. 5, No. 5, October 2013 Spatial multiplexing is a transmission technique in MIMO wireless communication system to transmit independent and separately encoded data signals, called as streams, from each of the multiple transmit antennas. Therefore, the space dimension is reused or multiplexed more than one time. If the transmitter and receiver has Nt and Nr antennas respectively, the maximum spatial multiplexing order (the number of streams) is NS =min (Nt ,Nr) (1) The general concept of spatial multiplexing can be understood using MIMO antenna configuration. In spatial multiplexing, a high data rate signal is divided into multiple low rate data streams and each stream is transmitted from a different transmitting antenna. These signals arrive at the receiver antenna array with different spatial signatures, the receiver can separate these streams into parallel channels thus improving the capacity. Thus spatial multiplexing is a very powerful technique for increasing channel capacity at higher SNR values. The maximum number of spatial streams is limited by the lesser number of antennas at the transmitter or receiver side. Spatial multiplexing can be used with or without transmit channel knowledge. Figure 2.Spatial Multiplexing Concept MIMO spatial multiplexing achieves high throughput by utilizing the multiple paths and effectively using them as additional channels to carry data such that receiver receives multiple data at the same time. The tenet in spatial multiplexing is to transmit different symbols from each antenna and the receiver discriminates these symbols by taking advantage of the fact that, due to spatial selectivity, each transmit antenna has a different spatial signature at the receiver . This allows an increased number of information symbols per MIMO symbol. In any case for MIMO spatial multiplexing, the number of receiving antennas must be equal to or greater than the number of transmit antennas such that data can be transmitted over different antennas. Therefore the space dimension is reused or multiplexed more than one time. The data streams can be separated by equalizers if the fading processes of the spatial channels are nearly independent. Spatial multiplexing requires no bandwidth expansion and provides additional data bandwidth in multipath radio scenarios [2]. 2. MIMO SYSTEM In MIMO system we use multiple antennas at transmitter and receiver side, they are extension of developments in antenna array communication. There are three categories of MIMO techniques. The first aims to improve the reliability by decreasing the fading through multiple spatial paths. Such technique includes STBC and STTC. The second class uses a layered approach to increase capacity. One popular example of such a system is V-BLAST suggested by Foschini et al. [2]. 86
- 3. International Journal of Wireless & Mobile Networks (IJWMN) Vol. 5, No. 5, October 2013 Finally, the third type exploits the knowledge of channel at the transmitter. It decomposes the channel coefficient matrix using SVD and uses these decomposed unitary matrices as pre- and post-filters at the transmitter and the receiver to achieve near capacity [3]. 2.1. Benefits of MIMO system MIMO channels provide a number of advantages over conventional Single Input Single Output (SISO) channels such as the array gain, the diversity gain, and the multiplexing gain. While the array and diversity gains are not exclusive of MIMO channels and also exist in single-input multiple-output (SIMO) and multiple-input single-output (MISO) channels, the multiplexing gain is a unique characteristic of MIMO channels. These gains are described in brief below: 2.2.1 Array Gain Array gain is the average increase in the SNR at the receiver that arises from the coherent combining effect of multiple antennas at the receiver or transmitter or both. Basically, multiple antenna systems require perfect channel knowledge either at the transmitter or receiver or both to achieve this array gain. 2.2.2 Spatial Diversity Gain Multipath fading is a significant problem in communications. In a fading channel, signal experiences fade (i.e they fluctuate in their strength) and we get faded signal at the receiver end. This gives rise to high BER. We resort to diversity to combat fading. This involves providing replicas of the transmitted signal over time, frequency, or space. . 2.2.3 Spatial Multiplexing Gain Spatial multiplexing offers a linear (in the number of transmit-receive antenna pairs or min (MR, MT) increase in the transmission rate for the same bandwidth and with no additional power expenditure. It is only possible in MIMO channels. Consider the cases of two transmit and two receive antennas. The stream is split into two half-rate bit streams, modulated and transmitted simultaneously from both the antennas. The receiver, having complete knowledge of the channel, recovers these individual bit streams and combines them so as to recover the original bit stream. Since the receiver has knowledge of the channel it provides receive diversity, but the system has no transmit diversity since the bit streams are completely different from each other in that they carry totally different data. Thus spatial multiplexing increases the transmission rates proportionally with the number of transmit-receive antenna pairs. 2.3 Modulation Modulation is the process of mapping the digital information to analog form so it can be transmitted over the channel. Modulation of a signal changes binary bits into an analog waveform. Modulation can be done by changing the amplitude, phase, and frequency of a sinusoidal carrier. Every digital communication system has a modulator that performs this task. Similarly we have a demodulator at the receiver that performs inverse of modulation. There are several digital modulation techniques used for data transmission. 87
- 4. International Journal of Wireless & Mobile Networks (IJWMN) Vol. 5, No. 5, October 2013 2.3.1 Phase Shift Keying Phase-shift keying (PSK) is a digital modulation scheme that conveys data by modulating, the phase of a reference signal (the carrier wave). In M-ary PSK modulation, the amplitude of the transmitted signals is constrained to remain constant, thereby yielding a circular constellation. Modulation equation of M-PSK signal is: ݏ ( = )ݐට ଶாೄ cosቀ2ߨ݂ ݐ ் (2) ଶగ ቁ ெ i=0,1….,M Figure 3.Constellation Diagrams of M-PSK (a) QPSK (b) QPSK (c) 8-PSK 2.4 Channels Channel is transmission medium between transmitter and receiver. Channel can be wired or wireless. In wireless transmission we use air or space as medium and it is not as smooth as wired transmission since the received signal is not only coming directly from the transmitter, but the combination of reflected, diffracted, and scattered copies of the transmitted signal. These signals are called multipath components. AWGN and Rician channels are taken into consideration for the analysis. 2.4.1 AWGN Channel AWGN channel is universal channel model for analyzing modulation schemes. In this model, a white Gaussian noise is added to the signal passing through it. Fading does not exist. The only distortion is introduced by the AWGN. AWGN channel is a theoretical channel used for analysis purpose only. The received signal is simplified to: y(t)=x(t)n(t) (3) where n(t) is the additive white Gaussian noise. y(t) is the received signal x(t) is the input signal 2.4.2 Rician Channel The direct path component is the strongest component that goes into deep fades compared to multipath components when there is line of sight. Such signal is approximated with the help of Rician distribution. The received signal can be simplified to: 88
- 5. International Journal of Wireless & Mobile Networks (IJWMN) Vol. 5, No. 5, October 2013 y(t)=x(t)*h(t)n(t) (4) where h(t) is the random channel matrix having Rician distribution and n(t) is the additive white Gaussian noise. The Rician distribution is given by: P(r) = మ మ ୰మ (ି ౨ శఽ ) ౨ ಚమ e IOቀమ ቁ మ (5) for (A 0, r 0) where A denotes the peak amplitude of the dominant signal and IO[.] is the modified Bessel function of the first kind and zero-order. 2.5 Detection Techniques There are numerous detection techniques available with combination of linear and non-linear detectors. The most common detection techniques are ZF, MMSE and ML detection technique. The generalized block diagram of MIMO detection technique is shown in Figure 4. Fig. 4 Block Diagram of system with equalizer 2.5.1 Zero Forcing (ZF) Detection The ZF is a linear estimation technique, which inverse the frequency response of received signal, the inverse is taken for the restoration of signal after the channel. The estimation of strongest transmitted signal is obtained by nulling out the weaker transmit signal. The strongest signal has been subtracted from received signal and proceeds to decode strong signal from the remaining transmitted signal. ZF equalizer ignores the additive noise and may significantly amplify noise for channel. The basic Zero force equalizer of 2x2 MIMO channel can be modelled by taking received signal ݕଵ during first slot at receiver antenna as: yଵ = hଵ,ଵ xଵ hଵ,ଶ xଶ nଵ =ሾhଵ,ଵ x hଵ,ଶ ሿ ቂ ଵ ቃ n1 xଶ (6) The received signal y2 at the second slot receiver antenna is: y2= hଶ,ଵ xଵ hଶ,ଶ xଶ nଶୀ ሾhଶ,ଵ x hଶ,ଶ ሿ ቂ ଵ ቃ nଶ xଶ (7) 89
- 6. International Journal of Wireless & Mobile Networks (IJWMN) Vol. 5, No. 5, October 2013 Where i=1, 2 in xi is the transmitted symbol and i=1, 2 in hi, j is correlated matrix of fading channel, with j represented transmitted antenna and i represented receiver antenna, is the noise of first and second receiver antenna. The ZF equalizer is given by: ିଵ W = ൫H ୌ ൯ Hୌ (8) Where WZF is equalization matrix and H is a channel matrix. Assuming MR ்ܯand H has full rank, the result of ZF equalization before quantization is written ିଵ as: y = ൫H ୌ H൯ HH y (9) 2.5.2. Minimum Mean Square Estimator (MMSE) Minimum mean square error equalizer minimizes the mean –square error between the output of the equalizer and the transmitted symbol, which is a stochastic gradient algorithm with low complexity. Most of the finite tap equalizers are designed to minimize the mean square error performance metric but MMSE directly minimizes the bit error rate. The channel model for MMSE is same as ZF [13],[14]. The MMSE equalization is ଶ Wୗ = arg ୫୧୬ E୶,୬ ሾฮx െ x ^ ฮ ሿ ୋ (10) Where is WMMSE equalization matrix, H channel correlated matrix and n is channel noise yୗ = H ୌ (HH ୌ n୭ I୬ )ିଵ y (11) 3. Results and Discussions This paper analyzes the Spatial Multiplexing(SM) technique for 2x2 antenna configuration under different modulation techniques for different fading channels i.e. AWGN and Rician channels. Results are shown in the term of BER vs SNR plots. 3.1 Using ZF detection 32-PSK modulation with 2x2 MIMO for AWGN and Rician channel with ZF 0 10 AWGN Rician -1 10 -2 Bit Error Rate 10 -3 10 -4 10 -5 10 -6 10 -7 10 0 10 20 30 40 50 Average Eb/No,dB 60 70 80 90 Figure 5(a). 90
- 7. International Journal of Wireless & Mobile Networks (IJWMN) Vol. 5, No. 5, October 2013 64-PSK modulation with 2x2 MIMO for AWGN and Rician channel with ZF 0 10 AWGN Rician -1 10 -2 Bit Error Rate 10 -3 10 -4 10 -5 10 -6 10 -7 10 0 10 20 30 40 50 60 Average Eb/No,dB 70 80 90 100 Figure 5(b). 128-PSK modulation with 2x2 MIMO for AWGN and Rician channel with ZF 0 10 AWGN Rician -1 10 -2 Bit Error Rate 10 -3 10 -4 10 -5 10 -6 10 -7 10 0 10 20 30 40 50 60 Average Eb/No,dB 70 80 90 100 Figure 5(c). 256-PSK modulation with 2x2 MIMO for AWGN and Rician channel with ZF 0 10 AWGN Rician -1 10 -2 Bit Error Rate 10 -3 10 -4 10 -5 10 -6 10 -7 10 0 10 20 30 40 50 60 Average Eb/No,dB 70 80 90 100 Figure 5(d). 91
- 8. International Journal of Wireless & Mobile Networks (IJWMN) Vol. 5, No. 5, October 2013 512-PSK modulation with 2x2 MIMO for AWGN and Rician channel with ZF 0 10 AWGN Rician -1 10 -2 Bit Error Rate 10 -3 10 -4 10 -5 10 -6 10 -7 10 0 10 20 30 40 50 60 Average Eb/No,dB 70 80 90 100 Figure 5(e). 0 1024-PSK modulation with 2x2 MIMO for AWGN and Rician channel with ZF 10 AWGN Rician -1 10 -2 Bit Error Rate 10 -3 10 -4 10 -5 10 -6 10 0 10 20 30 40 50 60 Average Eb/No,dB 70 80 90 100 Figure 5(f). Figure 5. BER vs. SNR plots over AWGN & Rician channel for SM technique using 2x2 MIMO System using ZF Equalization a)32 PSK b) 64 PSK c) 128 PSK d) 256 PSK e) 512 PSK f) 1024 PSK Table 1. Comparison of different Modulation Techniques for Rician& AWGN Channel for 2x2 MIMO Spatial Multiplexing using ZF Equalization Modulations Rician channel AWGN channel Improvement 32-PSK 62dB 57dB 5dB 64-PSK 63dB 69db 6dB 92
- 9. International Journal of Wireless & Mobile Networks (IJWMN) Vol. 5, No. 5, October 2013 128-PSK 74dB 69dB 5dB 256-PSK 81dB 75dB 6dB 512-PSK 86dB 81dB 5dB 1024-PSK 93dB 87dB 6dB From table we depict that at 32-PSK, 128-PSK, 512-PSK there is difference of 5dB between channels and there is difference of 6dB at 64-PSK, 128-PSK and 1024-PSK at BER of 10-4. Table shows the improvement in terms of decibels shown by proposed system employing SM technique for 2x2 MIMO system for different modulation schemes over different channels. 3.2 Using MMSE detection 32-PSK modulation with 2x2 MIMO for AWGN and Rician with MMSE 0 10 AWGN Rician -1 10 -2 Bit Error Rate 10 -3 10 -4 10 -5 10 -6 10 0 10 20 30 40 50 60 Average Eb/No,dB 70 80 90 100 Figure 6(a). 64-PSK modulation with 2x2 MIMO for AWGN and Rician with MMSE 0 10 AWGN Rician -1 10 -2 Bit Error Rate 10 -3 10 -4 10 -5 10 -6 10 0 10 20 30 40 50 Average Eb/No,dB 60 70 80 90 Figure 6(b). 93
- 10. International Journal of Wireless & Mobile Networks (IJWMN) Vol. 5, No. 5, October 2013 128-PSK modulation with 2x2 MIMO for AWGN and Rician with MMSE 0 10 AWGN Rician -1 10 -2 Bit Error Rate 10 -3 10 -4 10 -5 10 -6 10 0 10 20 30 40 50 60 Average Eb/No,dB 70 80 90 100 Figure 6(c). 256-PSK modulation with 2x2 MIMO for AWGN and Rician with MMSE 0 10 AWGN Rician -1 10 -2 Bit Error Rate 10 -3 10 -4 10 -5 10 -6 10 0 10 20 30 40 50 60 Average Eb/No,dB 70 80 90 100 Figure 6(d). 94
- 11. International Journal of Wireless & Mobile Networks (IJWMN) Vol. 5, No. 5, October 2013 512-PSK modulation with 2x2 MIMO for AWGN and Rician with MMSE 0 10 AWGN Rician -1 10 -2 Bit Error Rate 10 -3 10 -4 10 -5 10 -6 10 0 10 20 30 40 50 60 Average Eb/No,dB 70 80 90 100 Figure 6(e) 1024-PSK modulation with 2x2 MIMO for AWGN and Rician with MMSE 0 10 AWGN Rician -1 10 -2 B it E rror Rate 10 -3 10 -4 10 -5 10 -6 10 0 10 20 30 40 50 60 Average Eb/No,dB 70 80 90 100 Figure 6(f) Fig. 6 BER vs. SNR plots over AWGN & Rician channel for SM technique using 3x3 MIMO using MMSE Equalization a) 32 PSK b) 64 PSK c) 128 PSK d) 256 PSK e) 512 PSK f) 1024 PSK 95
- 12. International Journal of Wireless & Mobile Networks (IJWMN) Vol. 5, No. 5, October 2013 Table 2. Comparison of different Modulation Techniques for Rician &AWGN Channel for 2x2 MIMO Spatial Multiplexing using MMSE Equalization Modulations Rician channel AWGN channel Improvement 32-PSK 63dB 57dB 6dB 64-PSK 70dB 63dB 7dB 128-PSK 75dB 69dB 6dB 256-PSK 82dB 76dB 6dB 512-PSK 86dB 82dB 4dB 1024-PSK 93dB 87dB 6dB It can be seen from table that at 32-PSK, 128-PSK, 256-PSK and 1024-PSK there is an improvement of 6dB. At 64-PSK and 512-PSK there is difference of 7dB and 4dB at BER of 10-4. Table shows the improvement in terms of decibels shown by proposed system employing SM technique for 2x2 MIMO system for different modulation schemes over different channels. 4. CONCLUSIONS In this paper, an idea about the performance of the MIMO-SM technique at higher modulation levels is presented. We implemented 2x2 antenna configuration and used different signal detection technique at receiver end. It can be concluded BER is greater in Rician channel as compared to AWGN channel. Also BER (bit error rate) increases as the order of the modulation order i.e. M increases. This increase is due to the fact that as the value of M increases distances between constellation points decreases which in turn makes the detection of the signal corresponding to the constellation point much tougher The solution to this problem is to increase the value of the SNR so, that the effect of the distortions introduced by the channel will also goes on decreasing, as a result of this, the BER will also decreases at higher values of the SNR for high order modulations. ACKNOWLEDGEMENTS I express my sincere thanks to my esteemed and worthy guide Mr. Lavish Kansal, Assistant Professor, Electronics and Communication Engineering Department, Lovely Professional University, Phagwara, for his valuable advice, motivation, guidance, encouragement, efforts, timely help and the attitude with which he solved all of my queries regarding thesis work. I am highly grateful to my entire family and friends for their inspiration and ever encouraging moral support, which enable me to pursue my studies. 96
- 13. International Journal of Wireless & Mobile Networks (IJWMN) Vol. 5, No. 5, October 2013 REFERENCES [1] H. Jiang and P. A. Wilford, "A hierarchical modulation for upgrading digital broadcasting systems," IEEE Transaction on Broadcasting, vol. 51, pp. 222-229, June 2005. [2] P. W. Wolniansky, G. J. Foschini, G. D. Golden and R. A.Valenzuela, "V-BLAST: an architecture for realizing very high data rates over the rich- scattering wireless channel," In Proceeding of International symposium on Signals, Systems Electronics, pp. 259-300, October 1998. [3] J. Ha, A. N. Mody, J. H. Sung, J. Barry, S. Mclaughlin and G. L. Stuber, “LDPC coded OFDM with Alamouti/SVD diversity technique,” IEEE Journal on Wireless Personal Communication, Vol. 23 , Issue 1,pp. 183-194,Oct. 2002. [4] P. S. Mundra , T. L. Singal and R. Kapur, “The Choice of A Digital Modulation ,Schemes in A Mobile Radio System”, In proceedings of IEEE Vehicular Technology Conference, Issue 5, pp 1-4,( Secaucus, NJ)1993. [5] P. Liu & I1-Min Kim, “Exact and Closed-Form Error Performance Analysis for Hard MMSE-SIC Detection in MIMO Systems”, IEEE Transactions on Communication, Vol. 59, no. 9, September 2011. [6] P. Sanghoi & L. Kansal,” Analysis of WiMAX Physical Layer Using Spatial Multiplexing Under Different Fading Channels”, SPIJ, Vol.(6),Issue(3),2012. [7] C. Wang & E. K. S. Au, R. D Murch, W. H. Mow & V. Lau,” On the Performance of the MIMO Zero-Forcing Receiver in the Presence of Channel Estimation Error”, IEEE Transactions on Wireless Communication, Vol. 6,no.3,2007. [8] X. Zhang, Y. Su & G. Tao, “Signal Detection Technology Research of MIMO-OFDM System”, 3rd International Congress on Image and Signal Processing, pp 3031-3034, 2010. [9] I. Ammu & R. Deepa, “Performance Analysis of Decoding Algorithms in multiple antenna systems”, IEEE, pp 258-262, 2011. [10] H. B. Voelcker, “Phase-shift keying in fading channels” , In IEEE Proceeding on Electronics and Communication Engineering, Vol. 107, Issue 31, pp 31-38, 1960. [11] D. S. Shiu, G. J. Foschini, M. J. Gans, and J. M. Kahn, “Fading correlation and its effect on the capacity of multi-element antenna systems”, IEEE Transaction on Communication, Vol. 48, pp. 502– 513, 2000. [12] G. J. Foschini, K. Karakayali, and R. A.Valenzuela, “Coordinating multiple antenna cellular networks to achieve enormous spectral efficiency,” Communications, IEEE Proceedings, Vol. 153, pp. 548– 555, 2006. [13] J. S. Thompson, B. Mulgrew and Peter M. Grant, “A comparison of the MMSE detector and its BLAST versions for MIMO channels”, IET seminar on Communication System from Concept to Implementation, pp. 1911-1916, 2001. [14] X. Zhang and Sun-Yuan Kung, “Capacity analysis for parallel and sequential MIMO equalizers”, IEEE Transaction on Signal processing, Vol. 51, pp. 2989-3002, 2003. 97
- 14. International Journal of Wireless & Mobile Networks (IJWMN) Vol. 5, No. 5, October 2013 Authors Anuj Vadhera was born in Fazilka. She received her B.Tech degree in Electronics and Communication Engineering from Punjab Technical University, Jalandhar, in 2009, and pursuing M.Tech degree in Electronics and communication engineering from Lovely Professional University, Phagwara, India. Her research interests include MIMO systems, cognitive radios and wireless systems. Lavish Kansal was born in Bathinda. He received his B.Tech degree in Electronics and Communication Engineering from Punjab Technical University, Jalandhar, in 2009 and M.E. degree in Electronics and communication from Thapar University, Patiala in 2011. He is currently working as an Assis tant Professor in Lovely Professional University , Phagwara, India. He has published 18 papers in international journals. His research area includes Digital Signal Processing, Digital Communication & Wireless communication. 98