BT 6610 Digital Cordless Phone User Guide

Block
Nuisance
Calls
Block
Nuisance
Calls
Designed to block nuisance calls
Quick Set-up and User Guide
Nuisance
Calls
NuisanceNuisanceNuisanceNuisance
CallsCallsCallsCalls
Quick Set-up and User Guide
BT6610 Nuisance Call Blocker
Digital Cordless Phone with Answering Machine

If you need some help, call us on 0800 145 6789* or go to bt.com/producthelp
Important – please read ﬁrst2
• Only use the line cord, power supply and rechargeable batteries supplied with
your phone.
• Make sure that the power supply is connected to a known working socket.
• Connect your phone to the power supply and allow the batteries to charge for 24
hours before connecting the line cord to your telephone socket.
• To make sure you get the best range and reception from your handset, avoid
interference by placing the base unit away from large metal objects such as
fridge freezers and microwave ovens or electronic products such as computers
and TVs.
Answer machine – handy hint
Make sure the telephone is set to ‘Answer and record’ and that the Ring delay
is set to answer before any voicemail service i.e. BT Answer 1571, or similar.
The default setting is four rings. If you want to change this, please see page 47-48.

3
Check box contents
Handset Base
Telephone line cord
(pre-installed)
Handset Charger Mains power adaptor
(item code 066270)
2 x AAA Ni-MH 750 mAh
rechargeable batteries
(already in handset)
(pre-installed)
Mains power adaptor
(item code 066270)
2 x AAA Ni-MH 750 mAh
rechargeable batteries
(already in handset)
Important
Only use the mains power adaptors, cables and rechargeable batteries supplied in this box or this
product might not work. Any replacement rechargeable batteries must be of the same type.
BT accepts no responsibility for damage caused to your BT6610 if you use any other type of batteries.
Contents for each additional handset (multipacks only)

Where to put your phone
• Place the base within
3 metres of a mains power
socket and 3 metres of a
phone socket so the cables
will reach.
• Make sure it’s at least a
metre away from other
electrical appliances to avoid
interference.
• Don’t place the phone or
base in a bathroom or other
humid area.
• The product works by
sending radio signals
between the handset and
base. The strength of the
signal depends on where you
position the base. Putting it
as high as possible can help
give you the best signal.
IMPORTANT
• Don’t connect the phone line
to a phone socket until the
handset is fully charged.
• The base station should
be plugged into the mains
power socket all the time.
1. Plug the mains power
adaptor into the
base, with the cable
clipped in the
groove provided.
2. Plug the other end
of the power adaptor
into the wall power
socket and switch on.
Quick set-up guide4
1 Plug in
The phone line cord is pre-installed but don’t
plug the other end into the wall socket yet.
Turn the cable when clipping into the groove so
that the narrow part ﬁts between the clips before
turning cable back to secure.
1
2

Quick set-up guide 5
Talk/Standby time
Under ideal conditions, the
handset batteries should give
up to 22 hours talk time or
240 hours standby on a single
charge. (This doesn’t mean you
can unplug the base or leave
the handset for this length of
time without charge).
PleasenotethatnewNi-MH
rechargeablebatteriesdon’treach
full capacityuntil they’vebeenin
normal useforseveral days.
Battery low warning
The icon will flash, you’ll
see the message Battery low in
the display and hear a warning
beep every minute, to indicate
that you need to recharge your
handset. You can remove the
display message by selecting
Hide. If the battery charge
completely runs out, the display
will show Batteries flat. Please
charge. You must recharge
the handset batteries before
you can use the handset. If the
charge completely runs out the
handset will switch off. Place
the handset on the base or
charger to charge.
2 Activate the batteries
and charge
1. Activate the batteries by pulling the plastic tab
away from the bottom of the handset.
Rechargeable batteries
already fitted
Remove this tab
and charge batteries
for 24 hours before use.
2. The BT logo will appear on the screen, followed by
the set up wizard screen displaying Please set the
time and date to start using your telephone. Don’t
follow these instructions yet. Place your handset on
the base to charge first.
3. Place the handset on the base and leave to charge
for 24 hours.
IMPORTANT
Charge the handset batteries for 24 hours or your
phone might not work.

Quick set-up guide6
Battery performance
• To keep the batteries in the
best condition, leave the
handset off the base for a
few hours at a time.
• Running the batteries right
down at least once a week
will help them last as long as
possible.
• After charging your handset
for the ﬁrst time, subsequent
charging time for the
batteries is approximately
8 hours.
• The charge capacity of
rechargeable batteries will
go down over time, which
will reduce the talk and
standby time. Eventually
they’ll need replacing.
For details on how to get
replacement batteries,
call the helpline on
0800 145 6789*.
Hide
Line cord error.
Please check.
If your screen displays this message,
don’t worry. This is normal and
will continue to be displayed until
you connect the phone line cord
in step 4.
4. After 24 hours, plug the phone line cord into the
phone wall socket.
3 Follow the set up wizard
Follow the set up wizard to set the time and date,
record your outgoing message for the answer
machine, set up call blocking and add contacts.
Select YES by pressing the Left option button
if you want to follow the set-up wizard
prompt or select NO by pressing the Right option
button to continue to the next prompt until
set-up is complete.

Using your BT6610
on a broadband line?
To avoid problems with your
broadband or noise on your
phone line, you might need to
plug it into the wall socket via
a microfilter (not supplied).
If your main phone
socket has a single
socket, you do need
to use microfilters,
like this:
You’ll need a microfilter for
every phone socket where
you’ve got equipment plugged
in – up to a maximum of four
per line – including alarm
sytems and digital TV boxes.
You can get BT ADSL micro
filters from bt.com/shop
You don’t need to use
microfilters if your main phone
socket has two separate
sockets, like these:
4 Set up your additional
handsets (multipacks only)
1. For additional handsets and chargers: plug the
mains power adaptor into the back of the charger
and plug the other end into the mains wall socket
and switch on the power.
2. Activate the batteries as explained on page 5. If you
set the time and date on the first handset then it
will be shared with all other handsets in your multi
pack once you activate the batteries.
3. Place the handset on the charger to charge for
24 hours.

Quick set-up guide
8
If you ever need to remove the batteries, place
your ﬁngers in the groove at the bottom of the
handset and lift the cover up to release it.
Then, gently ease
the batteries out.
5 Go!
Your BT6610 is now ready for you
to use
• For instructions on making a call, go to page 22.
• For help personalising your phone’s settings,
go to page 59.
• For instructions on using the answer machine,
go to page 44.

Please note, other products
connected to the line are not
compatible with this feature
and will still ring.
You must subscribe to a Caller
Display service from your
network provider for the block
nuisance calls feature to work.
Charges may apply.
Blocked will be displayed with
no backlight on the handset
when a blocked call is received.
The handset or base will
not ring.
6 Block nuisance calls
The BT6610 blocks numbers in two separate ways
to help you avoid nuisance calls, firstly by type e.g
withheld or international and also by your choice of
specific numbers (you can store up to 100 numbers
of your own choice).
1. Select Menu, scroll to Call Control and
press Select.
2. Follow the instructions to set your PIN for the first
time and select OK, (see page 55).
3. Incoming calls is displayed, press Select.
4. Press to highlight Block calls and press
Select. You now have 2 choices:
i) To block calls by type, when By call type is
highlighted, press Select. Select Blocked or
Allowed for each of the call types by highlighting
each one using and ,: International,
Withheld number, No Caller ID and Payphone,
then select Save.
ii) To block calls by a specific number, press
to highlight By number and press Select. You will
enter the blocked numbers list, press Options and

Quick set-up guide
10
select Add. Enter the number you want to block (or
you can select Options and select a number from
your contacts or calls list) then select Save.
The Block button
The block call button can be used in 3 ways:
On incoming calls, during a call and in idle mode,
see page 30 under Call control settings.
7 Help
Most problems can be fixed with a few simple
checks, you may find the answer in the Help
section on page 80 or see our online frequently
asked questions at bt.com/producthelp
Alternatively, call the Helpline on 0800 145 6789*.
* Calls made from within the UK mainland network are free. Mobile and
international call costs may vary.
For more information and
general advice on handling
unwanted calls please go to
bt.com/unwantedcalls
For more information on Call
control settings, go to page 28.
No PIN number is required
when using the block call
button when there is an
incoming call or during a call.
If you cannot find the answer
to your problem in this user
guide, then please call our free
Helpline on 0800 145 6789*.
Our dedicated advisors are
more likely to be able to help
you than the retailer where you
made your purchase.

11 In this guide
Getting to know your phone
Handset buttons..............................15
Handset display/display icons...........17
Finding your way around your phone18
Menu map.......................................19
Base................................................21
Using the phone
Switch the handset on or off.............22
Make an external call .......................22
Preparatory dialling .........................22
End a call.........................................22
Call timer.........................................22
Receive a call...................................22
Call Waiting .....................................23
Mute...............................................24
Incoming speech/Handsfree volume.24
Handsfree .......................................25
Make a handsfree call.......................25
Answer a call handsfree....................25
Switch to handsfree during a call ......25
Redial .............................................25
Voicemail (1571) .............................26
Keypad lock.....................................26
Turn the handset ringer on or off.......27
Finding handset (paging) .................27
Call control settings
Set-up Do not disturb ......................28
Block nuisance calls .........................29
The block button .............................30
Set Parental Controls........................32
Assign VIPs......................................32
Change the access PIN .....................33
Contacts
Store a contact name and number ....34
Character map .................................35
View/dial a contact..........................35
Edit a contact entry..........................36
Delete selected or all contacts...........36
View the contact memory status.......37

In this guide 12
Speed dial
Save a speed dial entry.....................38
Dial a speed dial entry......................38
Edit a speed dial entry......................39
Delete a speed dial entry..................39
Caller Display and the Calls list
Caller Display...................................40
Calls list...........................................40
Missed call notiﬁcation.....................41
View and access options in
the Calls list .....................................41
Save a Calls list entry to your contacts42
Delete an entry in or the entire
Calls list...........................................43
Answer machine
Using the answer machine from
the handset.....................................44
Switch the answer machine on or off
and set the answer mode..................44
Outgoing messages..........................45
Record your own outgoing message..45
Play the current outgoing message...46
Reinstate the pre-recorded
outgoing message ...........................46
Record a memo ...............................47
Answer delay...................................47
Set the answer delay........................48
Set the maximum message length.....48
Set the message alert on or off .........49
Call screening via the handset...........49
Turn call screening on or off..............49
Using call screening .........................50
Message playback using the handset 50
Delete a message or delete all old
(played) messages ...........................52
Save a number in the answer phone
message list to your contacts............52
Send a text to a number in the
answer phone message list...............53
the base..........................................53
Switch the answer machine on or off.53

In this guide
13
Message playback using the base......54
Delete all old (played) messages .......55
Remote access.................................55
Set the remote access PIN for the
ﬁrst time .........................................55
Change the remote access PIN..........56
Turn remote access on/off ................56
If you forget to switch on your
answer machine...............................57
Operating your answer
machine remotely............................58
Settings
Set the handset ringtone for external or
internal calls and the ringer volume ..59
Turn the alert tones on or off ............59
Turn the handset tones on or off .......60
Change the handset display contrast.60
Change the handset name................60
Change the call settings (auto answer,
Autoend call, Autojoin and ﬁrst ring).61
Set the base ringtone melody
and volume .....................................61
Set a PBX access code ......................62
Change the system PIN.....................62
Turn Eco mode on or off ...................63
Reset the handset or base settings....63
Clear the handset or base user data...64
Clock/Alarm
Set the time and date.......................65
Set the time format (12 or 24 hour) ..65
Set an alarm ...................................66
Stopping the alarm when it goes off..66
BT Calling Features
Pre-stored numbers in the Calling
Features menu.................................67
Using Call Diversion..........................67
Cancel Ringback ..............................68
Using Call Waiting ...........................68

In this guide 14
Text messaging
Register to the text
messaging service............................69
Send a text message ........................70
Receiving text messages...................71
Reading messages ...........................72
Accessing the Inbox, Drafts folder
or Sent folder ..................................73
Edit a template ................................74
Turn new text message alert
on or off..........................................74
Service centre numbers....................75
Change the service centre numbers...75
Using additional handsets
Registering an additional handset.....76
De-register a handset ......................77
Make an internal call
between handsets............................78
Transfer a call...................................78
Hold a 3-way call.............................79
Help ...............................................80
General information
Safety information...........................87
Cleaning..........................................88
Environmental.................................88
How to recycle your equipment ........88
Guarantee .......................................89
Technical information.......................90
Connecting to a switchboard ............90
Recall (R).........................................90
R&TTE.............................................90
Declaration of Conformance .............90

15 Getting to know your phone
Handset buttons
Left option button
In idle mode, press to enter the main menu.
Also use to access sub menus and conﬁrm options shown on the display above the button.
Up/Volume
In idle mode, press to change the ringer volume, see page 59.
In talk mode, press to increase the incoming speech volume.
In menu mode, press to scroll up through the options.
Contacts
In idle mode, press to access your stored Contacts.
Talk/Handsfree
In idle mode, press to make and receive calls, see page 22.
In talk mode, press to switch handsfree on and off, see page 25.
Calls/Down
In idle mode, press to open and scroll through the Calls list, see page 40.
In talk mode, press to decrease the incoming speech volume.
In menu mode, press to scroll down through the options.
1 (Speed dial)
In idle mode, press and hold to dial BT 1571
or your stored speed dial number, see page 38.
Press and hold to turn the handset ringer on or off.
0
Press to enter a space.

Getting to know your phone 16
Call Block
In idle mode, press to enter the Call Control menu.
When receiving a call, press to send the call to the answer machine, or during a call, press to
end the call. If you have subscribed to a Caller Display Service and the Caller ID is displayed,
the number will be blocked and added to the blocked numbers list, see page 30.
Right option button
Press to conﬁrm the option displayed on the screen above the button, to delete or go back
to the previous screen.
In answer machine mode, deletes the current message playing.
OK
In idle mode, press to access a highlighted event e.g. missed calls, answer phone messages
and text messages on the display.
R (Recall)
R (Recall) for use with some BT Calling Features and when connected to a switchboard/PBX.
Left/Right
In idle mode, press to move left or right between the new events highlighted on the display
e.g. missed calls, answer phone messages and text messages. During menu navigation, use
to change settings. In text edit/entry mode, press to move the cursor.
End call/on or off
Press to end a call.
In idle mode, press and hold to switch the handset on or off, see page 22.
In menu mode, press to return to idle screen.
2-9 (Speed dial)
In idle mode, press and hold buttons 2-9 to dial a stored speed dial number, see page 38.
Press and hold to lock or unlock the keypad.

17
Handset display
Shows handset battery status.
Scrolls when the handset is charging.
Empty frame ﬂashes when battery
needs recharging.
On – missed call(s) in the Calls list*.
With number of calls displayed.
On – answer machine message(s) received
with number of messages displayed.
On – text message(s) received with
number of messages displayed.
On – Eco mode is on (for that handset).
On – answer machine on.
Off – answer machine off.
Flashing – new answer machine message
Memory full displayed when the answer
machine memory is full.
UnMute/Mute Indicates when Mute is on or off.
On – alarm is set.
Flashing – alarm time has been reached.
Off – alarm off.
The keypad is locked.
Handset ringer is switched off.
Handset display icons
Handset name
* For full details of who has called you please make sure you have subscribed to Caller Display from your
network provider.
Time

Finding your way around your phone
Your BT6610 has an easy to use menu system. Each menu has a list of options,
which you can see on the menu map on the next page.
When the handset is switched on and at the idle screen:
1. Select Menu by pressing the Left option button to open the main menu.
2. Use the or button to scroll through the available menu options.
3. When the menu you want is displayed, select by pressing the Left option button
or press .
4. Use the or button to scroll through the available sub menu options.
When the sub menu you want is highlighted, select by pressing the Left
option button or press .
Select the Back option if you want to return to the previous screen.
To exit a menu and return to the idle screen, press .
If no buttons are pressed for 30 seconds, the handset returns to the idle
screen automatically.
Left option button
Press to select the
option displayed on the
screen above the button.
Left and Right
navigation buttons
Use to select settings.
Right option button
Press to select the option
displayed on the screen above
the button.
Up and Down navigation buttons
Scroll up or down through the
menu options.

19
Menu map
Answer Phone View Messages Messages Play all
Delete message
Save number
Send text
Delete old msgs
Outgoing msg Ans. & record
Answer only
Record memo
Answer mode Answer on/off
Answer mode
(On or Off)
(Ans. & Rec or Answer only)
Settings Text alert On/Off
Ans. & record Answer delay
Max. msg length
Message alert
(2-10 rings or Time saver)
(1-3 minutes)
(On or Off)
Answer only Answer delay (2-9 rings or Time saver)
Call screening (On or Off)
Auto on/of On/Off
Remote access On/off
Change PIN
Call Control Incoming calls Do Not Disturb On/Off On
Off
Timed
On time
Off time
VIP calls
Allowed
Not Allowed
Block calls By call type
By number
International
Withheld number
No Caller ID
Payphone
Allowed
Blocked
Parentalcontrol Mobile calls
International
Premium rate calls
All dialled calls
(Allowed or Not Allowed)
VIP list
Change PIN
Clock/Alarm Alarm Alarm
Time AM/PM
Melody
(Off, On once, On daily, Mon to Fri, Sat & Sun)
(AM or PM)
(Melody 1-15)
Time and date Time AM/PM
Date
(AM or PM)
Time format (12 Hours or 24 Hours)
Record message
Play message
Use default msg

Text Messages Write Message
Inbox
Drafts
Sent folder
Templates
Settings
Please Cal.., I’ll be th.., What time.., I’ll call.., Happy Birt..)
Message alert
Service centres
Re-register
(On or Off)
(Send centre or Receive centre)
Speed Dial List 1. 1571 2-9 Empty (Edit or Delete)
BTCallingFeatures Call Diversion All calls
When busy
Not answered
(Set up, Cancel, Check status)
Cancel Ringback
Call Waiting (Turn On, Turn Off, Check status)
Settings Sounds Ringing External
Internal
Volume
(Melody 1-15)
(Melody 1-15)
(Ringer Off or Level 1-5)
Alert Tones Voice message
Text message
(On or Off)
Handset tones Keypad tones
Conﬁrmation
Display Contrast Level 1-5
Handset name
Call settings Auto answer
Auto end call
Auto join calls
First ring
(On or Off)
Base settings Ringing Ringtone (Melody 1-5)
Volume (Ringer Off or Level 1-5)
PBX Code
S/Ware version
Registration Register
De-register (Handset 1-5)
Change Sys. PIN
Auto-ECO (on/off)
Reset H/set settings
Base settings
Clear user data
Contacts menu
Accessed by pressing
the button
then Options.
Add new contact
Edit contact
Delete
Memory status
Calls list Menu
accessed by
pressing
Play message*
Save number
Delete call
Send text
Block number
Delete all
* If a message has been left on the answer machine.

21
Base
Vol-
Decrease the speaker
volume during playback,
the call screening volume
during idle and the base
ringer volume.
Vol+
Increase the speaker
volume during playback,
the call screening volume
during idle and the base
ringer volume.
Find
Press to ring all registered
handsets, helpful
for ﬁnding a missing
handset, see page 27.
Also used during the
registration process,
see page 76.
Play/Stop
When you have new
messages, the button
will ﬂash. Press once to
play new messages and
again to stop playback.
Skip<<
During playback, press
once to skip back to
the start of the current
message. Press twice to
skip back to the start of
the previous message.
Skip>>
During playback, press to
skip forward to the start
of the next message.
Light indicator
Blue light on when the handset is in the
base charging. Flashes when the line is in use
or registration is taking place.
Answer On
Press to turn the answer
machine on or off.
When set to On, the
text ‘On’ will light up
on the button.
Delete
Press once to delete the
message during playback.
In idle mode, press to
delete all old messages.

22
Auto end
If auto end is set to On you
can end a call by placing the
handset back in the base. If
auto end is set to Off, you’ll
need to press to end the
call. Auto end On is the default
setting. See page 61.
Out of range warning
When the handset is out of
range of the base, the display
will show Searching for base…,
the backlight will turn up to
100% to indicate the alert
message and you will hear a
warning tone. After 60 seconds
the display will show No base
link. Check base. You need to
move back within range of the
base station.
If you move out of range when
you’re on a call, you’ll lose your
connection. The handset will
automatically re-connect to
the base when you move back
within range.
To switch the handset off
1. Press and hold until the handset turns off.
To switch the handset on
1. Press and hold until the handset turns on.
Make an external call
1. Press .
2. When you hear the dial tone, enter the number.
Preparatory dialling
1. Enter the number ﬁrst. If you make a mistake select
Clear by pressing the Right option button to delete
the last digit.
2. Press to dial.
End a call
1. Press . Or, press to end the call and add
the caller’s number to the blocked numbers list, see
page 30 (only blocks if the number is available and if
you’ve subscribed to a Caller Display service).
Call timer
Your handset will automatically time your outgoing
and incoming calls. The handset shows the length of
time both during and for a few seconds after your call.
Using the phone

Using the phone
23
Auto answer
Auto answer Off is the default
setting to help with nuisance
calls. See page 61. If auto
answer is set to Off, you’ll need
to lift the handset off the base
and press to answer the
call. If auto answer is set to On
you can answer a call by just
lifting the handset off the base.
Receive a call
When you receive a call, the phone rings and the
display shows Incoming call and . If you’ve got a
caller display service, the display shows the caller’s
number if it’s available or the caller’s name if it
matches an entry stored in your contacts list.
1. To accept the call press .
Or
To block the call and send it to the answer phone
(even if it is switched off), press see page 30.
If you have subscribed to a Caller Display Service
and if the number is displayed, the caller’s telephone
number will be added to the blocked numbers list.
Call Waiting
If you’ve got a call waiting service and it is switched
on, your phone will alert you to a second incoming
call if you’re already engaged on an external call.
Toswitchyourcallwaitingserviceonoroff,seepage68.
1. You’ll hear the call waiting tone and if you also have
caller display the display will show the number of
the caller, or the name if it matches an entry in
your contacts.

Using the phone 24
2. Select Switch by pressing the Left option button
to answer the new call and your first caller is put
on hold.
3. Select Switch to toggle between the two callers.
4. Press to hang up the current call.
Mute
During a call, you can talk to someone nearby
without your caller hearing.
1. During a call, select Mute by pressing the Right
option button. The display shows Call muted and
your caller can’t hear you.
2. Select Unmute to return to your caller.
Incoming speech / Handsfree volume
During a call, you can adjust the handset incoming
speech or loudspeaker volume. There are five levels.
The default setting is Level 3.
1. Press or to increase or decrease the
volume. The first press will present the Call volume
screen so you can see the current volume level.
Subsequent presses will change the volume, you
will hear the volume level with each press.

Using the phone
25
Make a handsfree call
1. Enter the number then press twice. is
displayed. You hear your call over the handset
loudspeaker. Press to switch the call between
the earpiece and the loudspeaker.
2. Press to end the call.
Answer a call handsfree
When the phone rings:
1. Press after the call has been answered.
The call is transferred to the handset loudspeaker.
If Auto Answer is set to off (the default setting),
you will need to press twice.
Switch to handsfree during a call
1. During a call, press to put the call on the
loudspeaker. To switch handsfree off and return the
call to the earpiece, press again.
Redial
Telephone numbers that you have called are saved
in the Calls list. There is not a separate redial list, all
calls are saved in the Calls list. The Calls list holds up
to 50 incoming (missed and answered) calls and 30
outgoing calls.
Handsfree
Handsfree lets you talk to your
caller without holding the
handset and means that other
people in the room can listen
to your conversation over the
loudspeaker.
During a handsfree call,
press or to
change the volume.

Using the phone 26
You can lock the keypad so that
it can’t be used accidentally
while you’re carrying it around.
With the keypad locked, you
can still call the emergency
services on 999 and 112 using
preparatory dialling and you
can still answer incoming calls
and operate the in call features
as normal. When the call is
ended, the comes on again.
To redial a number, see ‘View and access options
in the Calls list’ on page 41. You can also save a
number you’ve called to your contacts, delete a
number you’ve called or delete all numbers from
the Calls list, see page 43.
Voicemail (BT 1571)
1. If you have subscribed to BT Answer 1571 you can
press and hold to listen to your messages.
Keypad lock
To lock the keypad
1. Press and hold for 2 seconds. The handset gives
a confirmation tone and Keypad locked is briefly
displayed before returning to the idle screen with
the icon displayed.
To unlock the keypad
1. Press and hold for 2 seconds. The handset gives
a confirmation tone and Keypad unlocked is briefly
displayed before returning to idle.

Using the phone
27
Turn the handset ringer on or off
1. Press and hold for 2 seconds to turn the handset
ringer on or off. The display will brieﬂy show Ringer
on or off before reverting to the idle screen with the
icon displayed if the ringer has been turned off.
Find handset (Paging)
You can ring a handset to help ﬁnd it.
1. Press on the base. All handsets registered to
the base will ring and the screen will show Base
searching for handsets for up to 2 minutes.
2. To stop the ringing, press on the base again or
press on any handset.
If you get an incoming call
or text message while you’re
paging a handset, the incoming
call or message takes priority
and paging will stop.
If the handset ringer is switched
off on a handset, it will be
temporarily switched back on so
the handset can be found.
Paging calls can’t be answered
by a handset.

28
This remote access PIN is
different to the system PIN.
See page 55-56.
Under the Call control menu are the features Do
not disturb, Block Calls and Parental control.
Do not disturb allows calls to be received silently
with minimal notification.
Parental control allows you to control the type of
outgoing calls that can be made. You can also assign
VIPs in your contacts to whom outgoing calls can
still be made even if Parental control is turned on
and calls can be received from as normal even if
Do not disturb is turned on.
To enter the Call control sub menu you need to
enter your remote access PIN. This will need to be
set the first time you try and enter the sub menu,
simply follow the on screen instructions. If you
have already changed the remote access PIN when
setting your remote access then you will not need
to set it again.
Set-up Do not disturb
press Select.
2. Enter the access PIN and select . Incoming Calls
is displayed, press Select.
3. Do Not Disturb is highlighted, press Select.
4. Press or to select On, Off or Timed. If you
select Timed you need to select the on and off times
You can set Do not disturb to
on, off or you can set specific
times when the feature is on
and off. The default setting
is off.
When set to On, the idle screen
will display DO NOT DISTURB
instead of the handset name.
When Do not disturb is set
to On, the base and handset
ringer volumes (on all handsets
registered to the base) will
be set to Off. The handset
backlight will not come on
when the phone rings and the
only tones that the handset
will emit are the battery low
and out of range warnings.
The base call screening volume
and message alert will also be
set to Off.

29
you want, press and enter the on time, then
again and enter the off time. Press to
highlight whether you want VIP calls to be Allowed
or Not Allowed using or , then press Save. The
chosen setting will be displayed and you will hear a
confirmation tone.
4Block nuisance calls
The BT6610 blocks numbers in two separate ways
to help you avoid nuisance calls, firstly by type e.g
withheld or international and also by your choice of
specific numbers (you can store up to 100 numbers
of your own choice).
press Select.
2. Follow the instructions to set your PIN for the first
time and select OK, (see page 55).
3. Incoming calls is displayed, press Select.
4. Press to highlight Block calls and press
Select. You now have 2 choices:
i) To block calls by type, when By call type is
highlighted, press Select. Select Blocked or
Allowed for each of the call types by highlighting
each one using and ,: International,
You must subscribe to a Caller
Display service from your
network provider for the block
nuisance calls feature to work.
Charges may apply.
Blocked will be displayed with
no backlight on the handset
when a blocked call is received.
The handset or base will
not ring.
No PIN number is required
when using the block call
button when there is an
incoming call or during a call.

Call control settings 30
Withheld number, No Caller ID and Payphone,
then select Save.
ii) To block calls by a speciﬁc number, press
to highlight By number and press Select. You’ve
entered the blocked numbers list, press Options and
select Add. Enter the number you want to block (or
you can select Options and select a number from
your contacts or calls list) then select Save.
The Block button
The block call button can be used in 3 ways:
1. Incoming call
When you have an incoming call, before pressing
the to answer, look at the handset display and
you can see who is calling. If you don’t want to take
the call press the on the handset and the call will
be transferred to the answering machine for the
caller to leave a message.
The number will be blocked and added to the
blocked calls list if Caller ID is displayed. If the
number calls again your phone will just ring silently
and the caller cannot leave another message.
If ‘All dialled calls’ is set to
Not Allowed, this will take
precedence over the other
settings except emergency
numbers 999 and 112 which
can still be dialled.
If ‘All dialled calls’ is set to
Allowed, the status of the
other settings will manage
which calls can be made.
The default for all Parental
control settings is Allowed.
The default setting is Allowed
for all call types.
If you select Allowed, calls from
this type of number will ring as
normal. If you select Blocked,
calls from this type of number
will be presented silently.
When you enter the block
calls list you can also edit or
delete numbers you’ve stored
previously by selecting Options,
then highlighting either Edit or
delete and pressing Select.

31
If you listen to the caller’s original message and
decide that the caller is not a nuisance caller and
you want to receive future calls from them, you can
remove them from the blocked numbers list. Go to
the Call Control menu and delete their number from
the blocked list, you will need to enter your PIN to
access the blocked number list (see page 55-56).
2. During a call
If you have already answered the call and you want
to block the number press , if the number is
displayed in the Caller ID, the display will give you
the option to select Yes and the number will be
added to the blocked numbers list and end the call,
or select No to go back to the caller.
3. In idle mode
Press as a shortcut to the Call Control menu
(see page 28).

Call control settings 32
You will be unable to use
BT 118500 from special
numbers when Premium Rate
calls are set to ‘Barred’.
You can set whether calls from
VIPs will still be allowed to
ring or not when the Do not
disturb feature is turned on. The
default setting is Allowed.
If set to Not Allowed all calls
will be presented silently. If set
to Allowed Calls from VIPs will
ring as normal.
If you’ve already added VIPs
to your VIP list the list will be
displayed when you enter the
VIP list menu. You can then
select Options to add further
VIPs, remove VIPs or assign a
VIP ringtone.
Set Parental control
select Options.
2. Enter the access PIN and select . Press to
highlight Parental Control and press Select.
3. Mobile calls is highlighted, press or to
select Allowed or Not Allowed, then press
to highlight International and follow the same
procedure for each option displayed and then
select Save. The display will show Parental control
settings saved. You will then be prompted to add
some VIPs if you haven’t already assigned any.
Assign VIPs
select Options.
2. Enter the access PIN and select OK. Press to
highlight VIP list and press Select.
3. Read the prompt and select Info, read the message
and select Yes. Your contacts list will be displayed.
4. To assign contacts as VIP, highlight the contact and
press . Select additional contacts if required by
repeating above.

33
The same access PIN is used for
remote access and call control.
5. Select Options, Add selected will be highlighted,
select OK and the selected entries will be added to
your VIP list.
Change the access PIN
1. Select Menu, scroll to Call Control and press
Options.
2. Enter the existing 4 digit remote access PIN. Press
to highlight Change PIN and press Select.
3. Once you’ve readtheremindermessage,selectOK then
enter the existing 4 digit access PIN and select OK.
4. Enter the new 4 digit access PIN and select OK, then
enter it again when prompted and select OK. Access
PIN saved will be displayed.

34
You must enter a name and at
least one telephone number for
the contact to be stored.
Names can be up to 25
characters and numbers up
to 24 digits.
Entering names
Use the keypad letters to enter
names, e.g. to store Tom: Press
once to enter T. Press
three times to enter o. Press
once to enter m.
Writing tips
To delete the last digit/
character entered, select Clear.
Press to switch between
text entry modes: sentence case
(Abc), upper case ABC), lower
case (abc) or numeric (123).
Press to insert a space.
To enter a pause in a
contact number
When storing a number, press
and hold in the place where
you want the pause.
To enter a recall in a
contact number
When storing a number, press
in the place where you
want the recall.
You can store up to 200 entries in your list of
contacts. For each contact you can save a home,
mobile and work number. Contact entries will
automatically be copied to any other handsets you
have registered to the base. Any change made on
one handset will be updated on all other handsets.
The handset will come with some special numbers
pre-stored. These will include Your BT Product
Helpline, BT 118500, All handsets (if you have
more than two handsets registered) and a list of the
handsets registered to the base according to their
default name/number (e.g. Handset 2 or 3 etc) or
name if you have stored one.
Store a contact
1. From the idle screen, press .
2. Select Options. Add contact is highlighted,
press Select.
3. Enter the new contact name using the keypad
(see note opposite for help) then press and
enter the home phone number. You can then press
and enter a mobile number and then a work
number if you want to. Select Save when you’ve
ﬁnished. The display will show Contact saved.
Contacts

Contacts
35
Searching alphabetically
You can alpha search for contact
names by entering multiple
characters, the search will be
carried out on the beginning
of the name only. e.g. enter
Ja and names beginning with
these two letters will be ﬁltered.
You can then scroll through the
ﬁltered list.
Character map
1 & . , ‘ ? ! @ 1
2 a b c 2 à á â ã æ ç
3 d e f 3 è é ê ë ë
4 g h i 4 î ï ì í
5 j k l 5 £
6 m n o 6 ö ô ò ó õ ø ñ
7 p q r s 7 $ ß
8 t u v 8 ü ù ú û
9 w x y z 9
0 space 0 + £ $ # *
* *
# Changes text entry mode (sentence case, upper, lower
or numeric)
View/dial a contact
1. From the idle screen, press to open your
contact list.
2. Press or to scroll through and view
the entries.
3. To dial an entry, press when the entry is
highlighted. If the entry has more than one number
saved under it you will need to highlight the
number you want and then press again.

Contacts 36
Edit a contact
1. From the idle screen, press .
2. Press or to scroll to the entry you want
to edit and select Options.
3. Press to highlight Edit contact and
press Select.
4. Edit the name by pressing or button to move
cursor left or right and Clear to delete characters
and use the keypad to enter new ones, then
press to move the cursor to edit any of the
numbers you have stored, using Clear to delete
digits and re-enter any new ones, then select Save.
The display will show Contact saved.
Delete selected or all contacts
1. From the idle screen, press , then select
Options.
2. Press until Delete contact is highlighted and
press Select.
You cannot edit the special
contact entries that the handset
has pre-programmed in the
memory.
When a contact is deleted it will
also be deleted from the VIP
call control list, see page 32.
You cannot delete the
special contact entries that
are pre-programmed in the
contacts list.

Contacts
37
You can also highlight Clear
selection if you want to remove
the ticks so the contacts are not
marked for deletion anymore.
The delete all contacts
feature will not delete the
special contact entries that
are pre-programmed in the
contacts list.
3. You can now either:
Select which contact(s) to delete by scrolling to
highlight the contact and pressing . A tick will
mark the contact for deletion. Once all the contacts
you want to delete have been marked, select
Options. Delete selected will be highlighted, select
OK, then select Yes to conﬁrm.
Or, to delete all contacts, select Options and scroll
to highlight Select all, then select OK then
Yes to conﬁrm.
View the contact memory status
1. From the idle screen, press , then
select Options.
2. Press until Memory status is highlighted and
press Select.
3. The display will show the percentage of the contact
memory used, e.g. 35% Full.

38Speed dial
If you try to save a Speed
dial entry under a Speed dial
button that has already been
populated, the display will show
Replace existing number? and you
will hear an error tone. You can
either overwrite the existing
entry by selecting Yes or you
can press and hold a different
Speed dial button or select No.
Save a Speed dial entry
1. From the idle screen, enter the telephone number
you want to store.
2. Then, either:
Press and hold the Speed dial button to you
want to store the number under.
Or,
Select Options, scroll to highlight Set speed
dial and press Select. Scroll to the speed dial
location number you want (1-9) and select Save.
The display will show Saved as speed dial x (x being
the Speed dial button).
Dial a Speed dial entry
1. Either, press and hold the Speed dial button to
under which the entry you want to dial is stored.
Or, Select Menu, scroll to display Speed Dial
List and press Select. Scroll to highlight the
entry you want then press . The number will
be dialled automatically.
You can allocate a name and
number to each of the Speed
dial buttons to . Button
is pre-programmed with
1571 but you can delete this
and replace it with an entry
of your choice. Once a Speed
dial entry has been stored
you can simply press and
hold the Speed dial button to
automatically dial the number
stored under it (names are only
shown if taken directly from the
contact list).

Speed dial
39
Edit a Speed dial entry
1. Select Menu, scroll to display Speed Dial List
and press Select.
2. Press or to highlight the entry you
want to edit and select Options.
3. Edit is highlighted, press Select.
4. Edit the number by selecting Clear to delete digits
and then enter any new digits. Select Save. Saved
as speed dial x will be displayed.
Delete a Speed dial entry
1. Select Menu, scroll to display Speed Dial List
and press Select.
2. Press or to highlight the entry you
want to delete and select Options.
3. Scroll to highlight Delete and press Select.
4. Delete speed dial x? is displayed, select Yes. Speed
dial x deleted will be displayed.

40
You’ll need to subscribe to
your network provider’s Caller
Display service for this feature
to work. You might have to pay
a fee. For more information on
BT Calling Features, call BT free
on 0800 800 150.
To make sure the caller’s name
is displayed, make sure you’ve
stored the full telephone
number in your contacts list,
including the dialling code.
You can store more than one
number for the same caller.
There are some incoming
calls where a number is not
displayed and a network
message is recorded instead:
Unavailable = number
is unavailable
Withheld = number has
been withheld
International = international
number
Operator = call from the operator
Payphone = call from a
payphone
Ringback = a ringback call
Caller Display
If you’ve subscribed to a Caller Display service,
you’ll be able to see your caller’s number on your
handset display (provided it’s not withheld) before
you answer a call. If your caller’s name is stored
in your contacts list and it matches the number
calling, you’ll see the caller’s name and where they
are calling from (i.e. Home, Mobile or Work) on the
display instead. If you haven’t subscribed to a Caller
Display service Incoming call will be displayed when
you receive a call. If you receive a call from
a number you have stored in your Blocked calls
list Blocked will be displayed under the name
or number.
Calls list
The Calls list holds up to 50 incoming (missed and
answered) calls and 30 outgoing calls. The date
and time of the call is also stored. If you haven’t
subscribed to a Caller Display service, No number will
be displayed in the Calls list for incoming calls but the
time and date will still be recorded.
Calls are listed in chronological order with the most
recently received/made call at the top of the list.

41
Calls list indicators
= outgoing call made
= incoming call received
= missed call
= caller left a voice message
When the Calls list is open,
press to scroll from the
newest call to the oldest, or
press to scroll from the
oldest call to the newest.
If you only want to view the
missed calls list, from the
idle screen when the is
displayed press . The missed
calls list will be displayed and
you can view and access the
same options as described for
the complete calls list.
When the list is full and a new call is received/made,
the oldest entry will be deleted automatically. The
Calls list can hold numbers up to 24 digits and
names up to 25 characters.
Missed call notiﬁcation
If an incoming call has been missed (i.e. not
answered), the missed call icon will be displayed
on the idle screen with the number of missed calls
displayed underneath it e.g. . You can clear the
notiﬁcation by viewing the calls list on any handset
registered to the base. The icon will still be
presented for missed calls in the calls list so you
can differentiate between calls. See Calls list
indicators opposite.
View and access options in the Calls list
1. Press or select Calls. The most recent entry
is at the top of the list. (If there are no entries List
empty will be displayed.
2. Press or toscrollthroughandviewthelist.
3. To dial an entry, when the entry you want is
highlighted, press .
To play an answer message, when the entry you
want is highlighted, select Options, Play message is
highlighted, press Select. The message will be played.

Caller Display and the Calls list 42
If you have more than one
handset registered to the base,
all data is synchronised across
handsets. Therefore, if you save
a calls list entry to your contacts
it will be saved on all handsets.
To send a text message to the caller, when the
entry you want is highlighted, select Options, scroll
to Send text , press Select and follow the
instructions to send a text as detailed on page 69.
To block the number, when the entry you want is
highlighted, either press or, select Options,
scroll to Block number and press Select.
If you haven’t set up your access PIN yet, you will
be prompted to follow the instructions.
If the access PIN has been set you will be prompted
to enter the 4 digit PIN, then select OK.
The number you selected to block is highlighted,
select Save. Blocked number saved will be
displayed.
Save a Calls list entry to your contacts
1. Press or select Calls, then press or
to highlight the entry you want and
select Options.
2. Highlight Save number and press Select.
3. You now have two options:
For further instructions on call
blocking see page 29.

43
If you need to edit the name,
press the or button
to move the cursor left or
right and use Clear to delete
unwanted characters then use
the keypad to enter new ones.
You can replace an existing
number if you want to.
If you have more than one
handset registered to the base,
data is synchronised across
all handsets. Therefore, if you
delete a calls list entry on one
handset it will be deleted on
all handsets.
i) To save this as a new contact, highlight New contact
and press Select. Highlight the type of number,
then press Select. Enter the contact name and
select Save.
ii) To add to an existing contact, highlight Add to
contact and press Select. Scroll to highlight the
entry you want and press Select. Highlight the
number type where you want to save the number
(Home, Work or Mobile) and press Select.
Delete an entry in or the entire Calls list
1. Press or select Calls, then if you want to
delete just one entry, press or to
highlight the entry and select Options. To delete
the entire list, simply select Options.
2. Press to display either Delete call or Delete
all and press Select. Call deleted will be displayed if
you have deleted one entry, if you chose to delete
all then you will need to conﬁrm by selecting Yes.

44Answer machine
You’ll need to set the date and
time (if you’ve not already done
so during set-up) so that the
answer machine can correctly
announce when each message
was received. To set the date and
time manually, see page 65.
When the answer machine is
switched on, the text On will
light up on the button.
The default answer mode is
Answer & Record using the
female voice.
Your BT6610 can digitally record up to 30 minutes
of messages. You can operate your answer machine
from: the handset, the base (see page 53) or
remotely from any other Touchtone™ telephone
(see page 55).
If you receive a call from a number you have stored
in your Blocked calls list, the caller will not be able
to leave an answer phone message.
the handset
Switch the answer machine on or off and set the
answer mode
1. Select Menu, Answer Phone is displayed, press
Select.
2. Press until Answer mode is highlighted,
press Select.
3. Press or to select On or Off then scroll
to set the answer mode, press or to highlight
Ans. & Rec or Answer only and then select Save.
Answer mode saved will be displayed and the
current answer mode will be announced.

Answer machine
45
Answer & Record
The pre-recorded Answer &
Record outgoing message
that allows your caller to leave
a message is, “Hello, your
call cannot be taken at the
moment, so please leave your
message after the tone”.
Answer Only
The pre-record Answer Only
outgoing message, where
callers hear an announcement
but can’t leave a message, is
“Hello, your call cannot be
taken at the moment and you
cannot leave a message, so
please call later”.
When recording your Answer
Only message, remember to
let your caller know that they
won’t be able to leave
a message.
The default outgoing message
mode is Answer & Record using
the female voice.
If your answer machine is full
you will not be able to record
your outgoing message.
Outgoing messages
The outgoing message is the message a caller ﬁrst
hears when the answer machine picks up their
call. There are two pre-recorded male and female
outgoing messages to choose from, one that allows
callers to leave a message (Answer & Record) and
one that simply answers the call (Answer Only) or
you can record your own.
Record your own outgoing message
1. Select Menu, Answer Phone is displayed,
press Select.
2. Press until Outgoing msg is displayed,
press Select.
3. Press or to highlight the outgoing
message mode you want: Ans. & record or Answer
only and press Select.
4. Record message is highlighted, press Select.
Follow the voice prompt to record your message
and select Save when you’ve ﬁnished.
5. Your message will be played back to you. Select
OK if you’re happy with it or you can delete it by
selecting Delete.

Answer machine 46
Reinstating the pre-recorded
outgoing message will not
delete your recorded outgoing
message. It will be retained
in case you want to use it in
the future.
Play the current outgoing message
Select.
press Select.
4. Press to highlight Play message and press
Select to hear the outgoing message. If the current
outgoing message being played is your recorded
message you can delete it if you want to by
selecting Delete.
Reinstate the pre-recorded outgoing message
Select.
press Select.

Answer machine
47
You can record a memo
message on the answer
machine for other users to hear
when they listen to messages.
You can only record memos
using the handset. Memo
messages are played back in
exactly the same way as normal
answer machine messages, see
page 50 and 54.
4. Press to highlight Use default msg and
press Select.
5. Press or to display On. Scroll and then
use or to display either Female or Male and
select Save. Saved will be displayed.
Record a memo
Select.
2. Press until Record memo is displayed,
press Select.
3. Follow the voice prompt to record your memo and
select Save when you’ve ﬁnished.
4. Your memo will be played back to you. Select OK
if you’re happy with it or you can delete it by
selecting Delete.
Answer delay
The answer delay setting sets how many times the
phone will ring before the answer machine takes
the call. You can choose from 2–10 rings or Time
saver. The default setting is 4 rings.

Answer machine 48
Time saver
When you ring in to access your
answer machine remotely, if
you have set Time saver as the
answer delay and you have new
messages it will answer after
2 rings. If you don’t have new
messages it will answer after 6
rings. This means you can hang
up knowing that you have no
new messages, saving you the
time and the cost of the call.
For compatibility with BT 1571
(or another voicemail service)
Make sure the answer delay is
set for your answer machine
to answer before the voicemail
service. Therefore, the answer
delay should be less than on
your voicemail service. For BT
1571 do not set the answer
delay to more than 5 rings.
Set the answer delay
Select.
2. Press until Settings is displayed, press Select.
3. Press to highlight either Ans. & record or
Answer only and press Select.
4. Answer delay is displayed, use or to display
the number of rings you want (2–10 rings or Time
saver) and select Save. Saved will be displayed.
Set the maximum message length
You can set the maximum length that an answer
machine message can be: 1 minute, 2 minutes or 3
minutes. The default setting is 3 minutes.
Select.
3. Press to highlight Ans. & record and press
Select.
4. Press to display Max. msg length and then
press or to select the length you want and
select Save. Saved will be displayed.

Answer machine
49
When the message alert is set
to On, the base will beep at
regular intervals. The default
setting is On.
Set the message alert on or off
Select.
3. Press tohighlightAns.&recordandpressSelect.
4. Press to display Message alert and then
press or to select On or Off and select Save.
Saved will be displayed.
Call screening via the handset
When call screening is turned on and the answer
machine takes a call, you can listen to the caller
leaving a message. You can then identify the caller
and decide whether to take the call in person.
Turn call screening on or off
Select.
3. Press to highlight Call screening on/off
press Select.
4. Press or to display On or Off and select Save.
The default setting is call
screening Off.
When Auto-answer is set to
ON (see page 61) and Call
Screening is set to OFF, you
can intercept the caller leaving
a message by picking up the
phone from the base without
the need to press any keys.

Answer machine 50
While screening, you can adjust
the volume by pressing
or on the handset or
or on the base.
When you receive new
messages you’ll be notiﬁed by
an answer phone icon displayed
on the idle screen with the
number of messages displayed
underneath it e.g. and the
button on the base will
ﬂash. The number of messages
displayed includes all messages
stored, new and old (played).
When a message is deleted
the counter will be updated
accordingly. You can also set an
audible alert, see page 49.
Each message is played back
with the day, date and time it
was received announced.
Using call screening
When the phone rings, wait for the answer machine
to take the call. When the caller begins to leave a
message, the display will show Leaving a message,
underneath the callers number (or name if you have
added as a contact and a caller display service).
If you wish to listen to the message being recorded,
press the left option key to select Listen or, if you wish
to talk to the caller, press to take the call. Talking
to the caller will stop the recording if it’s started.
Message playback using the handset
1. Highlight the answer phone icon on the idle screen
and press , or
i. SelectMenu,AnswerPhoneisdisplayed,pressSelect.
ii.View Messages will be displayed, press Select.
2. A list of your answer phone messages will be
displayed with the most recently received
highlighted at the top.
3. Use or to scroll through the list to
highlightthemessageyou wish to listen to andpress .
i. If you have more than one message stored and
want to listen to them all, select Options.
Play all will be highlighted, press Select.

Answer machine
51
New (unplayed) messages are
played ﬁrst (oldest to most
recent) and then old (played)
messages (oldest to most
recent).
If the memory is full, the answer
phone icon on the idle screen
will display Full underneath it.
You can still enter the answer
phone menu and playback your
messages, however, you will see
a warning message Memory full.
No messages can be left before
you enter the menu and Memory
full will be announced before
new or old messages are played
back.
Message playback is stopped if
you receive an incoming call.
You can toggle between private
playback through the handset
and handsfree playback by
pressing the button. The
default is private playback.
Unless you delete a message,
it’s automatically saved.
4. As each message is played, the handset will display
the number or the name if you have Caller Display
and a name/number match and the time and date it
was received. If you have any old (already listened
to) messages these will be played after your new
messages.
During playback you have the following options:
or to adjust the playback volume.
to switch private playback through the
handset to handsfree playback.
or once to repeat the current message
playing from the beginning.
or twice within a second to skip back to the
previous message.
or once to skip forward to the next message.
Delete or to delete the current message playing.
At the end of playback, you will hear, “End
of messages,” and the same message will be
displayed. The answer phone icon on the idle screen
will be renumbered to take into account any deleted
messages.

Answer machine 52
To cancel deletion, when you
see the confirmation question,
select No.
Delete a message or delete all old (played) messages
1. Select Menu, Answer Phone is displayed, press Select.
2. View Messages will be displayed, press Select. A list
of your answer phone messages will be displayed.
3. Select Options and scroll to highlight
either Delete message or Delete all old msgs
and press Select.
4. A confirmation question will be displayed, select Yes
to confirm deletion.
Save a number in the answer phone message list to
your contacts
Select.
2. View Messages will be displayed, press Select.
Highlight the number you want to save and select
Options.
3. Scroll to highlight Save number and press
Select.
4. You now have two options:
i) To save this as a new contact, highlight New
contact and press Select. Highlight the type of
number, then press Select. Enter the contact name
and select Save.

Answer machine
53
When the answer machine is
switched On, the text ‘On’ will
light up on the button.
Send a text to a number in the answer phone
message list
Select.
2. View Messages will be displayed, press Select.
Highlight the number you want to send to and
select Options.
3. Scroll to highlight Send text and press
Select.
4. Enter and send your text message as per the
instructions detailed on page 70.
the base
Switch the answer machine on or off
Press to toggle between On and Off.
The setting is announced.

Answer machine 54
Memory full
If there is only 10 seconds of
memory capacity left when a
caller is leaving a message they
will hear, “Please complete your
message within 10 seconds.” If
a caller is still leaving a message
when the memory expires they
will hear, “Memory full. Thank
you for calling”, and the call will
be ended.
If your answer machine
memory becomes full and it is
set to Answer and record it will
automatically switch to Answer
only mode. Once messages
have been deleted and there
is memory available again, the
machine will revert to Answer
and record mode (unless
you have changed the mode
yourself to Answer only using
the handset menu).
You will need to delete
messages before your answer
machine will be able to record
new ones. To delete old (played)
messages, see page 52 and 55.
Message playback using the base
Press . If you have messages they will be played,
new (unplayed) messages ﬁrst followed by old
(played) messages.
During playback:
Press to stop playback. The base will return
to idle.
Press to delete the message being played.
Press to skip forward to the start of the next
message.
Press to skip back to the start of the current
message.
Press twice to skip back to the start of the
previous message.
Press or to increase or decrease the playback
volume level.
At the end of playback the base will return to idle
mode and messages will be renumbered to take into
account any deleted messages.

Answer machine
55
If you don’t press within
3 seconds you will hear,
“Messages saved”.
The Remote access PIN is also
used for the Call control PIN.
Delete all old (played) messages
1. In idle mode, press . The base will announce,
“To delete all old messages, press Delete”, press
again within 3 seconds to delete all old messages.
You will hear, “All old messages deleted.”
Remote access
With remote access you can operate your answer
machine from any Touchtone™ phone, even if you
forget to turn on your answer machine before you
go out. You need to set a remote access PIN first
and then you will need to turn remote access On if
you want to use this feature.
Set the remote access PIN for the first time
Select.
3. Press to highlight Remote access and
press Select.
4. Read the message prompt, press to read it
all, then select Set PIN.
5. Enter a 4 digit PIN of your choice and select OK.
6. Enter the 4 digit PIN again to confirm and select
OK. The display will show Access PIN saved.

Answer machine 56
You cannot turn Remote access
On until you have set a remote
access PIN.
The default setting is Off.
Select Clear if you need to
delete any digits.
Change the remote access PIN
Select.
press Select.
4. Press to highlight Change PIN and press
Select. You will be reminded that the access PIN is
used for both remote access and call control.
5. Enter your old 4 digit PIN and select OK.
6. Enter the new 4 digit PIN, select OK, then enter the
new PIN again and select OK. The display will show
New Access PIN saved.
Turn remote access on or off
Select.
press Select.
4. On/Off is displayed, press Select.
The Remote Access PIN is also
used for the Call Control PIN.

Answer machine
57
Remote Access must ﬁrst be
enabled to allow you
to switch on the answer
machine remotely.
5. Press or to display On or Off and select Save.
If you forget to switch on your answer machine
1. Call your number from another phone and let it
ring. After 20 rings the machine will switch on and
answer your call.
2. Press *and enter your 4 digit remote access PIN
when prompted. Play back your messages as shown
on page 58 in, ‘Operating your answer machine
remotely’. If you do not choose to switch your
answer machine On, it will switch off when the call
is ended.

Answer machine 58
Operating you answer machine remotely
1. Dial your phone number.
2. When you hear your outgoing message, press
*and enter your 4 digit remote access PIN.
3. Follow the voice prompts to:
To replay the current message
To play all messages
To delete during messages
To skip back during messages
To set Answer machine OFF, or ON
To skip forward during messages
Turn Text Alert OFF, or ON
To play your outgoing message
To record a new outgoing message
To set to Answer Only, or Answer & Record
To hear the main menu options

59
Choose from 15 handset
ringtones. The default external
ringtone is Melody 1 and the
internal ringtone is Melody 2.
There are 5 handset ringer
volume levels plus Ringer Off.
The default setting is Level 3.
If you turn the ringer off, the
icon will be displayed on the
idle screen.
As a quick way to turn the
handset ringer off, press
and hold .
There are two alert tones: voice
message (answer phone) and
text message tones. You can
turn these on or off, the default
setting is On. When the voice
message alert is set to On,
the base will beep at regular
intervals when you receive an
answer phone message. When
the text message alert is set
to On, the handset will beep
at regular intervals when you
receive a text message.
Handset settings
Set the handset ringtone for external or internal
calls and the ringer volume
1. Select Menu, scroll to display Settings and
press Select.
2. Sounds is highlighted, press Select. Ringing is
highlighted, press Select.
3. Press or to highlight the external melody
you want, then press to select the internal
melody you want from the 15 ringtones.
4. Press again to select the volume level you
want and select Save to save your choices.
Turn the alert tones on or off
press Select.
2. Sounds is highlighted, press Select. Press to
highlight Alert tones and press Select.
3. Press or to highlight On or Off for the Voice
message alert and then press to highlight On
or Off for the Text message alert and select Save.
Settings

Settings 60
There are two handset tones:
keypad tones and confirmation
tones. You can turn these on or
off, the default setting is On.
Keypad tones: when turned on,
you will hear a beep after each
button press.
Confirmation tones: when
turned on, you will hear a tone
after each successful action
or after an error has occurred.
This does not include the
battery charging tone when the
handset is placed on the base/
charger, low battery or out of
range warnings or tones used in
calls such as Call Waiting or
Call Intercept.
There are 5 contrast levels
to choose from. The default
setting is Level 3.
A handset name can be a
maximum of 12 characters.
If you name your handset,
the handset number will be
removed, e.g. instead of saying
Kitchen 1 the name would just
be Kitchen. To revert back to the
default handset name (Handset
x), delete all the characters and
select Save.
Turn the handset tones on or off
press Select.
2. Sounds is highlighted, press Select. Press to
highlight Handset Tones and press Select.
3. Press or to highlight On or Off for Keypad
tones and then press to highlight On or Off for
Confirmation tones and select Save.
Change the handset display contrast
press Select.
2. Press to highlight Display and press Select.
3. Press or to select the level you want, then
select Save.
Change the handset name
press Select.
2. Press to highlight Handset name and
press Select.
3. Edit the name by selecting Clear to delete
the characters, then enter the new name and
select Save.

Settings
61
The default setting is Auto
answer Off to help with
managing any nuisance calls.
If Auto answer is set to On you
can answer a call by lifting the
handset off the base. If it’s set
to Off, you’ll need to lift the
handset off the base and then
press .
If Auto end is set to On you
can end a call by placing the
handset back in the base.
If Auto end is set to Off,
you’ll need to press to
end the call.
With Auto join calls set to
On you can automatically
join an existing call from
another registered handset
without being invited to join
the call, you can simply press
to join.
With First ring set to Off, an
incoming external call will be
displayed visually before the
handset(s) start to ring for the
second burst of ringing.
Change the call settings (Auto answer, Auto end
call, Auto join and First ring)
press Select.
2. Press to highlight Call settings and press
Select.
3. Press or to highlight On or Off for Auto answer
and then press to highlight On or Off for Auto
end call, follow the same procedure for Auto join
calls and First ring, then select Save.
Base settings
Set the base ringtone melody and volume
Choose from 5 base ringtones. The default is
Melody 1. There are 5 base ringer volume levels
plus Ringer Off. The default is Level 3.
press Select.
2. Press to highlight Base settings and
press Select.
3. Ringing is highlighted, press Select.
4. Press or to highlight the ringtone melody you
want, then press to select the volume level
you want and select Save to save your choices.

Settings 62
If you wish to revert to not
using a PBX access code, you
need to go into the PBX code
menu and delete all the digits
by selecting Clear, then select
Save.
PBX access code
If you’re connected to a switchboard, you might
need to enter an access code (e.g.9) before each
number is dialled. Your BT6610 can store an access
code which is automatically dialled before each
number.
Set a PBX access code
press Select.
2. Press to highlight Base settings and press
Select.
3. Press to display PBX Code and press Select.
4. Enter the number you want (maximum of 4 digits)
and select Save.
Change the system PIN
press Select.
2. Press to highlight Change Sys. PIN and
press Select.
3. If the current PIN is 0000, you will be prompted
to enter the new 4 digit PIN, then press OK. (Or, if
the current PIN is not 0000, you will be prompted
The default system PIN is 0000.
You can change this to your
own preferred 4-digit code.
The system PIN is different
to the call control PIN.
See page 33.
The system PIN is used when
changing certain settings and
for registration/de-registration.
If you make a mistake, select
Clear to delete a digit.

Settings
63
If you reset the handset settings
all the handset settings will
return to their default settings,
e.g. the handset name, ringer
melody, all volume levels,
display and alarm settings.
If you reset the base settings all
the base settings will return to
their default settings, e.g. the
base ringer melody, all volume
levels, PBX access codes and
answer machine settings.
The default setting is Eco
mode Off.
to enter the old (current) 4 digit PIN ﬁrst and then
select OK. Then follow the prompts and enter the
new 4 digit PIN).
4. Enter the new 4 digit PIN again and select OK.
The display will show New system PIN saved.
Turn Eco mode on or off
With Eco mode on, the handset only uses the
transmission power it needs to communicate
with the base rather than full transmission power all
the time.
press Select.
2. Press to highlight Auto-ECO and press
Select.
3. Press or to highlight On or Off for Auto answer
and then press to highlight On or Off and
select Save.
Reset the handset or base settings
press Select.
2. Press to highlight Reset and press Select.

Settings 64
If you clear the handset and
base user data all your contacts
and the calls list will be deleted
and your recorded outgoing
messages and all received
answer machine messages will
be deleted.
3. H/set settings is highlighted, press Select or press
to highlight Base settings and then press
Select.
4. Reset <handset or base> settings back to default?
is displayed, select Yes.
5. Resetting <handset or base> settings… is
displayed while the reset takes place. Once ﬁnished,
<handset or base> settings reset back to default is
displayed.
Clear the handset and base user data
press Select.
2. Press to highlight Reset and press Select.
3. Press to highlight Clear user data and
press Select.
4. If the current system PIN is not 0000 you will be
prompted to enter the PIN then press OK. If it is
0000, you will continue straight to step 5.
5. Delete data on all handsets and base? is displayed,
select Yes.
6. Deleting all user data… is displayed. Once ﬁnished,
All user data deleted is displayed.

65 Clock/Alarm
You must enter the full date:
day, month and year.
You must enter both time and
date otherwise nothing will be
saved.
If you didn’t set the time and date when you ﬁrst
set-up your phone then you will need to do so
before you can set an alarm. The clock will also be
displayed on the handset screen in idle mode.
If you have subscribed to a Caller Display service the
time and month will be set when you receive your
ﬁrst call but you will still need to set the year.
Set the time and date
1. Select Menu, scroll to display Clock/Alarm
and press Select.
2. Press to highlight Time and date and
press Select.
3. Use the keypad to enter the digits for the time.
4. Press then or to select AM or PM, then
press again and enter the date. Select Save.
Set the time format (12 or 24 hour)
and press Select.
2. Press to highlight Time format and
press Select.
3. Press or to display 12 hours or 24 hours and
press Save.
The default time format is
12 hour.

Clock/Alarm 66
If you select Off the display will
show Alarm off and you will
hear a confirmation tone.
If you set an alarm the display
will show the time and
frequency setting after you
select Save.
When you’ve set an alarm, the
icon will appear on the idle
screen to confirm an alarm has
been set.
If an incoming call is received
while the alarm is going off,
the alarm notification will
immediately stop and the
incoming call will be shown
on the display. The alarm will
not resume.
Set an alarm
and press Select.
2. Alarm is highlighted, press Select.
3. Press or to display the alarm frequency you
want: Off, On once, On daily, Mon to Fri or Sat &
Sun then press and enter the alarm time,
(you will also need to select AM or PM if you have
set 12 hour format), then press and to select
the melody you want. Select Save.
Stopping the alarm when it goes off
When the alarm goes off, the selected melody will
play at an ascending volume, the handset backlight
will flash and the display will show the alarm time.
The alarm will sound for 30 seconds and then
the handset will return to idle, if the alarm isn’t
stopped or set to snooze, it will sound once more
after 1 minute.
To stop the alarm, press or select Stop.
To activate a ten minute snooze, select Snooze or any
other button (except or Stop). You can set snooze
as many times as you want until you select Stop.

67
You need to subscribe to the
speciﬁc BT Calling Feature to
be able to use some of these
services. You might have to pay
a fee.
For more details on BT’s
Calling Features, go to
bt.com/callingfeatures, refer to
the user guide supplied when
you subscribed to the services
of your choice or call BT free on
0800 800 150.
If you’re not connected to the
BT network, some of these
features may not be available.
Call diversion services might
allow other divert options.
Please contact your telephone
network provider for details.
Call Diversion will divert
incoming calls to another
number of your choice. You can
choose all calls to be diverted or
calls only to be diverted when
the line is busy or only calls that
are not answered.
You can easily access a number of BT Calling
Features using the Calling Features menu.
Pre-stored numbers in the Calling Features menu
Call Diversion
Ringback
Call Waiting
Using Call Diversion: set up, cancel or check status
1. Select Menu, scroll to display Calling
Features and press Select.
2. Call Diversion is highlighted, press Select.
3. Press or to highlight the diversion
option you want: All Calls, When busy or Not
answered and press Select.
4. Press or to display either: Set up,
Cancel or Check status and press Select.
5. If you selected Set up, you will need to enter the
telephone number to divert to (or press and
select the number from your contacts), then select
Set up. If you chose Cancel or Check status, the
service will be called, follow the spoken instructions
or listen for conﬁrmation/status.
BT Calling Features

BT Calling Features 68
With the ring back feature you
can get an automatic call back
from an engaged number. No
need to dial a busy number over
and over again. Just dial 5, wait
for a confirmation message and
hang up. Your phone will keep
trying the busy number for up
to 45 minutes.
Call Waiting lets you know if
another person is trying to call
you while you’re on another
call. If a second caller rings, you
will hear a beep in the handset
earpiece. If you’ve subscribed
to Caller Display, the display will
show the caller’s details as well.
Cancel Ringback
2. Press to highlight Cancel Ringback press
Select.
3. The service will be called and the display will show
Cancelling. Follow the spoken instructions or listen
for confirmation/status.
Using Call Waiting
2. Press until Call Waiting is highlighted,
press Select.
3. Press or to highlight either Turn On,
Turn Off or Check status and press Select. The
service will be called. Follow the spoken instructions
or listen for confirmation/status.

69 Text messaging
Your BT6610 can send and receive text messages
from participating networks and compatible
landline telephones in the UK. The ﬁxed line text
service is provided under BT’s terms and conditions
for telephone service. These can be found by
visiting the bt.com website at http://www.bt.com/
terms. There is no subscription charge (other than
the subscription to Caller Display). Visit bt.com to
ﬁnd out how much it costs to send a text message,
the cost will depend on your call package.
All messages in the inbox and sent folders are
synchronised across all handsets registered to the
base. Additions and deletions made on one handset
are synchronised across all registered handsets.
Draft messages remain local to each handset.
Register to the text messaging service
You need to regsister for the text messaging service
under the text messages menu to use this feature.
You can register following these instructions:
1. Select Menu, scroll to display Text messages
and press Select.
IMPORTANT
You must subscribe to your
network provider’s Caller
Display service to use text
messaging and you must
not withhold your telephone
number. A fee may be payable,
please contact your network
provider for more details.
You may also send messages to
landline phones that are NOT
text compatible. Messages to
non-compatible lines will be
delivered in spoken words to
the telephone as a call. Please
note that the conversion can
translate common abbreviations
and smileys etc, but to ensure
maximum clarity of message
delivery, abbreviations should
be used sparingly.

Text messaging 70
The sent and drafts folders are
populated on a first in, first out
basis. Once the folder is full,
when a new message is added
to the folder the oldest message
will automatically be deleted.
If you receive a call while
writing a text your text message
will automatically be saved
in the drafts folder when you
answer the call.
You can also insert a symbol
by scrolling to highlight
Insert Symbol and pressing
Select.
2. Press until Settings is highlighted, press Select.
3. Press until Re-register is highlighted, press
Select. Re-register to receive text messages is
displayed, select Send. A text message containing
the word ‘Register’ will be sent to the number
00000 and you will receive a confirmation message
in return.
Send a text message
and press Select.
2. Write message is highlighted, press Select.
3. Use the keypad to enter your message.
4. Select Options. Send to will be highlighted:
To send the message, press Select and enter the
telephone number (or press , select a number
from your contacts and press Select) then select Send.
To save the message in the drafts folder, scroll
to highlight Save and press Select.
To insert a symbol in your message, press the
button then use the navigation buttons to highlight
the symbol you want then select Use.

Text messaging
71
There are 5 templates:
Please call home
I’ll be there at
What time will you be home?
I’ll call you back
Happy Birthday!
To insert a template, scroll to highlight Insert
template and press Select. Scroll to highlight the
template you want then select Use.
To delete the message, scroll to highlight
Delete message and press Select. Delete message?
will be displayed select Yes.
Receiving text messages
When you receive a text message the new message
alert will sound (unless you’ve turned the alert off
or you are using another audio feature like playing
answer phone messages) and the new message
alert screen will be presented for 4 seconds over
the idle screen. The total number of messages
received will be displayed on the screen e.g. for two
messages the icon is displayed with the number
of text messages received underneath it.

Text messaging 72
If the Inbox is full you will see
a warning message letting
you know that no new text
messages can be received
until you delete some old
messages, select OK to read
your messages.
Reading messages
1. From the alert screen, select Read or from the idle
screen, highlight the icon then press .
2. A list of your received text messages will be
displayed. To read a message, highlight it, then
press , you can use or to scroll
through the message if necessary.
3. You can then press Back to return to the message
list to read other messages or select Options and
scroll or to highlight one of the
following:
Delete message Press Select. Delete message? will
be displayed, select Yes (or No) to cancel.
Reply Press Select. Enter your message using
the keypad, then select Options. Send to will be
highlighted, press Select. The telephone number
(or name) will be displayed, press Send.
Forward Press Select. The message will be
displayed, select Options. Send to will be
highlighted, press Select. Enter the telephone
number (or press , select a number from your
contacts and press Select) then select Send.

Text messaging
73
In the Inbox, unread messages
are marked with the • icon. Once
read, the icon will be removed.
Save number Press Select. You now have two options:
i) To save this as a new contact, highlight New
contact and press Select. Highlight the type of
number, then press Select. Enter the contact name
and select Save.
Delete msgs. Press Select. You now have two
options: i) To select certain messages to delete,
you need to highlight each message in turn and
press OK to select the message for deletion – a in
the box indicates it has been selected, then select
Options. Delete selected will be displayed, select
OK, then select Yes. ii) To delete all messages, press
Options, scroll to highlight Select all and
select OK.
Accessing the Inbox, Drafts folder or Sent folder
and press Select.

Text messaging 74
You can change any of the 5
pre-populated templates to
messages of your choice up to
a maximum of 32 characters. If
you delete all the characters in
a template it will be displayed
as ‘Empty template’ in the
template list.
The pre-populated
templates are:
Please call home
I’ll be there at
What time will you be home?
I’ll call you back
Happy Birthday!
When a text message is received
you will hear an audible alert.
The default setting for the text
message alert is On but you can
turn this off if you want to.
2. Press to highlight either Inbox, Drafts or
Sent folder, then press Select.
3. A list of the messages will be displayed, press
or to scroll through the list. You can press OK
to read a highlighted message or select Options to
access the list of menu options.
Edit a template
and press Select.
2. Press until Templates is highlighted,
press Select.
3. Press to highlight the template you want to
edit and select Edit.
4. Select Clear to delete characters and use the keypad
to enter your new template text, then select Save.
Turn new text message alert on or off
and press Select.
3. Message alert is highlighted, press Select.
4. Press or to highlight On or Off and select Save.

Text messaging
75
Do you have two text phone
bases connected to the same
phone line?
If you have you are likely to
experience problems receiving
text messages. Normally, only
one SMS/text enabled base unit
can be plugged into any line.
If you want to keep more than
one connected, see page 85.
Service centre numbers
To send and receive text messages you need the
telephone number of your network’s text centre.
If you accidentally delete the send or receive service
centre numbers you will need to re-enter them in
order for your text service to work. The send and
receive centre numbers are pre-populated for BT’s
PSTN text message service but you can change
them to another service if you want to.
BT’s text message send service number is:
1470P17094009 and the receive service number
is: 0800587529.
Change the service centre numbers
and press Select.
3. Press until Service centres is highlighted,
press Select. Highlight either Send centre or
Receive centre and select Edit.
4. Select Clear to delete the digits, then enter the new
number and select Save.

76Using additional handsets
You can register up to six GAP
compliant handsets to your
BT6610 base to extend your
phone system without needing
to install telephone extension
sockets for each new phone.
If a handset becomes
un-registered it will need to be
registered to the base again.
Please register this handset will
be displayed, select OK then
follow the instructions starting
from point 4 below.
You have 2 minutes to complete
the registration process. After 2
minutes the In use light on the
base will stop flashing.
If registration isn’t successful
the first time, please try again
incase the base registration
period ran out of time.
If there are already six handsets
registered to the base, the
registration will fail. You must
de-register another handset
before you can register the
new one.
If you’ve bought a BT6610 multiple pack, any
additional handsets come pre-registered to the
base. However, if you purchase an additional
handset separately, you must register it to your
BT6610 base before it can be used.
Register an additional handset
press Select.
2. Press to highlight Registration and press Select.
3. Register is highlighted, press Select.
4. Press and hold Find button on base is displayed.
5. Press and hold on the base until you hear a
beep and the In use light starts to flash.
6. Immediately, select OK on the handset. The handset
will display Registering handset to indicate the
base is in registration mode. If the system PIN is not
0000 then you will be prompted to enter it, then
select OK.
7. Once registration is successful the handset will show
Handset x registered (with X being the assigned
handset number). The handset will then synchronise
data with any other registered handsets, e.g. contacts,
speed dials, handset names and text messages.

77
Registering another make
of handset to your BT
6610 base
If you want to register another
make of handset (i.e. not a
BT6610 handset) to your
BT6610 base you will need
to follow the Registration
instructions that came with
the handset ﬁrst and then
continue with the base part of
the registration procedure (as
shown in point 4 on page 76).
Please note that registering
other types of handset will only
provide limited compatibility
i.e. you may only be able to
make and receive calls on the
additional handset.
De-register a handset
press Select.
2. Press to highlight Registration and
press Select.
3. Press to highlight De-register handset and
press Select.
4. Press or to highlight the handset you
wish to de-register and press Select.
5. If the system PIN is not 0000 then you will be
prompted to enter it, then select OK. If it is 0000,
you will continue straight to point 6.
6. The display will show De-registering handset and
once successful the display will conﬁrm the handset
has been de-registered.

Using additional handsets 78
You can also choose All
handsets if you want to call
all handsets registered to the
base. If a handset answers, the
handset name will be displayed
on your screen.
If an external call is received
while an internal call attempt
is being made, the internal
call will be abandoned and
base will ring and display the
external call information.
You can also choose All
handsets if you want to call
base. If a handset answers, the
handset name will be displayed
on your screen.
If the internal call is not
answered after 30 seconds you
will see Handset not available
on your display and you will be
returned to your external caller.
Make an internal call between handsets
If you have more than one handset registered
to the base, you can make internal calls between
two handsets.
1. Press , then press to scroll through
and display the handset you want to call, then
press .
2. The receiving handset will ring and your handset
name will be presented on the screen. To answer
they need to press . If it is not answered after
30 seconds, you will see Handset not available on
your display.
3. Press to end the call.
Transfer a call
You can transfer an external call to another handset
registered to the base.
1. During a call, select Options, then press to
highlight Transfer call and press Select.
2. If you have one other handset it will ring, if you
have more than one other handset you can press
or to highlight the handset you want,
then select Call and it will ring. Your external call
will be put on hold.

79
3. When the other handset answers you can announce
the call and then select Transfer or press to
transfer the call.
Hold a 3-way call
Using your handset, you can hold a 3-way call
with two external callers. Or, you can hold a 3-way
call between 2 internal handsets and 1 external
caller. Once the 3-way call is in progress other
handsets registered to the base can join the call by
pressing .
1. During a call, select Options. Multi call is
highlighted, press Select.
2. Either enter the number you want to call or press
and scroll to the number you want or the
internal handset you want and then press
to call. When the second call is answered, the ﬁrst
external caller will be put on hold.
3. Select Join and all callers will be joined in a
3-way call.

80Help
Phone doesn’t work
• Have you activated the batteries correctly? See page 5.
• Check that the mains power is correctly connected.
No dial tone or line cord error message displayed on screen
• Is the telephone cord plugged into the base and phone wall socket?
• Only use the telephone cord supplied with the phone.
Can’t make or receive calls
• The batteries may need recharging.
• Check that product call barring is not active – see Parental control on page 32.
• Has there been a power cut? If so, place the handset back on the base for ten
seconds and try again. If it still doesn’t work, disconnect the batteries and mains
power for ten minutes, then reconnect and try again.
You have a dial tone, but the phone won’t dial out
• If you’re connected to a switchboard, check whether you need to dial an
access code, see page 62.
Handset doesn’t ring
• The ringer volume may be switched off, see page 59.
• Do Not Disturb may be switched on, see page 28.
• Block nuisance calls may be switched on, see page 29.
• Make sure the handset is registered to the base, see page 76.

Help
81
No display
• The batteries may be ﬂat, dead or incorrectly inserted.
• Recharge or replace the batteries.
Range icon ﬂashes
• Make sure the handset is registered to the base, see page 76.
• Check that the mains power is correctly connected to the base.
• Check that the handset is within range of the base.
• If the batteries are low, place the handset on the base/charger to recharge.
You hear the busy tone when you press
• Make sure the handset is in range of the base.
• Another handset registered to your BT6610 base may be on the line and
Auto Join is switched off, please see page 61.
Answering machine doesn’t record any messages
• The memory may be full. Play and delete old messages, pages 50-51 and 54-55.
Answering machine messages have the wrong date and time
• Have you set the date and time? See page 65.
Can’t access your messages from another phone
• Have you changed the remote access PIN? See page 55-56.
Always keep a note of the new PIN in a safe place.
• Has Remote access been turned off? To turn remote access on, see page 56.

Help 82
No Caller Display number/name displayed
• Have you subscribed to a Caller Display service from your network provider?
See page 40.
• The caller may have withheld their number.
• Network may not have the callers number information.
• An exact name/number match was not found in your contacts. Check that you’ve
stored the full STD dialling code.
Can’t register a handset to a base
• You can register up to six handsets to your BT6610 base and your BT6610
handset can only be registered to one base. Check that you’ve not exceeded
the limits.
• Check that you’ve entered the correct system PIN number (default PIN 0000).
• Check that you’re at least one metre away from other electrical equipment to
avoid interference when registering.
Base unit does not ring, but the lights are on
• Have you connected the telephone line correctly?
• Do Not Disturb may be switched on, see page 28.
• Block nuisance calls may be switched on, see page 29.
• Is the base ringer set to off?
• You may have a faulty line or socket. Try using another socket or line.
If you are a BT customer then please call 0800 800 151 or your network provider
if you still have problems.

Help
83
Buzzing noise on my phone or on other electrical equipment nearby
• Sometimes other electrical equipment can interfere with your BT6610 if it’s
placed too close. We recommend that you place your BT6610 at least one metre
away from electrical appliances or metal obstructions to avoid any risk
of interference.
Customer Helpline
If you’re still having problems, call us on 0800 145 6789* or go to
bt.com/producthelp
General sales enquiries
• BT Residential lines – call 150. BT Business lines – call 152.
• For non BT line customers, call 0800 800 150 (residential) or 0800 800 152
(business).
• Additional handsets available to purchase from the Helpdesk on 0800 145 6789*.
Billing enquiries
Please see the phone number shown on your BT bill.
Possible problems with text messaging
Text messages cannot be sent
• The base station power supply or telephone line cord might not be
properly connected.
• Check that the base station power supply is plugged into the mains socket and
switched on and that the telephone is plugged into the telephone wall socket.

Help 84
• There might be a fault on the line. Check your telephone line is working properly.
• You might have deleted the server number in error. See page 75 for instructions
on how to enter the number.
Cannot send text
• Check service centre number is correct including 1470P prefix (this is for BT lines.
If you have another network provider please check the prefix number with them),
see page 75. In order to send and receive text messages you must not withhold
your number. If you normally withhold your number the 1470 prefix presents your
number for you.
Cannot receive text
• You will not be able to receive text messages until you have first sent a message.
The first message sent registers you with the text service.
• More than one text messaging product is plugged into the line. Either remove
the other text (SMS) enabled products or see on page 85 “I want to use more
than one text (SMS) enabled product on my telephone line” for alternative
instructions.
• Check service centre number is correct.
• Ensure you have subscribed to a Caller Display service and that it is active.
You can check this by noting if your phone displays your caller’s number when
you receive an incoming call.

Help
85
I want to use more than one text (SMS) enabled product on my telephone line
It is possible to connect more than one SMS product to the same telephone line
and for both of them to send and receive Text messages, but you must amend the
final digit of both the Send and Receive Service Centre telephone numbers first.
All BT text capable telephones are provided with the same send and receive
telephone numbers, but with two or more text capable telephones connected to
the same telephone line, delivery of text messages becomes unreliable causing
the text to be delivered as a normal telephone call which when answered will be
an electronic Text to Speech message.
To overcome this problem you must keep one of the products as it is with the
default Send & Receive ending in a ‘9’, but for the second and subsequent products
you must change the final digit of the Service Centre numbers (from the default
‘9’) to any unique number between 1 and 8 i.e for a second product change last
digit from a ‘9’ to a ‘1’ by changing the Send number from 1470P17094009 to
1470P17094001 and the Receive number from 0800587529 to 0800587521.
For example, for the Send number, go to Menu - Text messages - Settings - Service
centres - Send centre - Edit - amend the last digit and then press Save….

Help 86
Once changed, for the products that you have assigned new send and receive
numbers, you need to send a new registration text to the Fixed Line Text Service
platform to register the new identity (i.e. send a text to 00000 from the product
that you changed the Send & Receive numbers).
You can then send and receive text messages from more than one product.
Text has previously been sent and received but you are now only receiving voice
spoken text messages, from number 0845 6021111.
• This may be due to your line being de-registered at the text service centre.
Please see page 69 and repeat instructions to register to receive and send
text messages.
Further help and advice for text queries on BT lines:
• BT Residential customers – call 151, choose option 2, when prompted by the
Fault Management Service select option 2, enter your phone number on the
handset and wait to speak to a customer adviser.
• BT Business Customers – call 152, choose option 2, when prompted by the Fault
Management Service select option 2, enter your phone number on the handset
and wait to speak to a customer adviser.
• For other telephone service providers please contact their customer services.

87 General information
Important
This equipment is not designed for making emergency
phone calls when the power fails. Alternative
arrangements should be made for access to
emergency services.
This product is intended for connection to analogue
public switched telephone networks and private
switchboards in the United Kingdom.
Replacing the handset batteries
After a time, you might find that the handset batteries
run out of charge more quickly. This is a standard sign
of wear and the batteries will need replacing.
1. Open the battery compartment cover.
2. Lift the battery out and remove the batteries.
Replace with two new AAA Ni-MH 750mAh
rechargeable batteries.
3. Replace the battery compartment cover.
Caution
Don’t immerse batteries in water, throw them into a fire
or dispose of them with ordinary domestic refuse.
BT accepts no responsibility for damage caused to your
BT6610 by using any other types of batteries.
There is a risk of explosion if incorrect batteries are fitted.
Safety information
• Only use the power supply suitable for the BT6610.
Using an unauthorised power supply will invalidate
your guarantee and may damage the phone. The item
code for the base mains power supply is 066270 .
If you’ve bought a multiple pack, the item code for the
charger mains power supply is 066270.
• Use only the approved rechargeable batteries supplied.
Spare rechargeable batteries are available from the
BT6610 Helpline on 0800 145 6789*.
• Don’t open the handset (except to replace the
handset batteries) or the base. This could expose you
to high voltages or other risks. Contact the Helpline
on 0800 145 6789* for all repairs.
• If the keypad is locked, it is still possible to make calls
to 999 and 112 emergency numbers by dialling the
number then pressing .
• Radio signal transmitted between the handset and
base may cause interference to hearing aids.
• It is recommended that advice from a qualified
expert be sought before using this product in
the vicinity of emergency/intensive care medical
equipment.
• It is recommended that if you have a pacemaker
fitted you check with a medical expert before using
this product.
• Your product may interfere with other electrical
equipment, e.g. TV and radio sets, clock/alarms and
computers if placed too close.
• It is recommended that you place your product
at least one metre away from such appliances to
minimise any risk of interference.
• Never dispose of batteries in a fire. There is a serious
risk of explosion and/or the release of highly toxic
chemicals.

General information 88
Cleaning
• Clean the handset and base (or charger) with a
damp (not wet) cloth, or an anti-static wipe.
Never use household polish as this will damage the
product. Never use a dry cloth as this may cause a
static shock.
Environmental
• Do not expose to direct sunlight.
• The handset may become warm when the batteries
are being charged or during prolonged periods of
use. This is normal. However, we recommend that to
avoid damage you do not place the product on any
surface susceptible to heat damage.
• Do not stand your product on carpets or other
surfaces which generate fibres, or place it in locations
preventing the free flow of air over its surfaces.
• Do not submerge any part of your product in water
and do not use it in damp or humid conditions, such
as bathrooms.
• Do not expose your product to fire, explosive or
other hazardous conditions.
• There is a slight chance your phone could be
damaged by an electrical storm. We recommend
that you unplug the power and telephone line cord
during an electrical storm.
How to recycle your equipment
The symbol shown here and on the product
means that the product is classed as electrical
or electronic equipment, so DO NOT put it in
your normal rubbish bin.
It’s all part of the Waste Electrical and Electronic
Equipment (WEEE) Directive to recycle products in
the best way – to be kinder to the planet, get rid of
dangerous things more safely and bury less rubbish
in the ground.
You should contact your retailer or supplier for advice
on how to dispose of this product in an environmentally
friendly way.
Warning
You won’t be able to call 999 from this phone if there’s
a power cut, so make sure you’ve got another way to
call for help in an emergency.
R&TTE Directive & Declaration of Conformity
This product is intended for use within the UK for
connection to the public telephone network and
compatible switchboards.
This equipment complies with the essential
requirements for the Radio Equipment and
Telecommunications Terminal Equipment Directive
(1999/5/EC).
For a copy of the Declaration of Conformity please
refer to bt.com/producthelp

General information
89
Guarantee
Your BT6610 is guaranteed for 12 months from the
date of purchase.
Subject to the terms listed below, the guarantee
will provide for the repair of, or at BT’s or its agent’s
discretion, the option to replace the BT6610 or any
component thereof, (other than batteries), which is
identiﬁed as faulty or below standard, or as a result of
inferior workmanship or materials. Products over 28
days old from the date of purchase may be replaced
with a refurbished or repaired product.
Guarantee conditions
• The guarantee shall only apply to defects that occur
within the 12 month guarantee period.
• Proof of purchase is provided.
• The equipment is returned to BT or its agent as
instructed.
• This guarantee doesn’t cover any faults or defects
caused by accidents, misuse, fair wear and tear,
neglect, tampering with the equipment, or any
attempt at adjustment or repair other than through
approved agents.
• This guarantee does not affect your statutory rights.
Within the 12 month guarantee period
Prior to returning your product, please read the Help
section beginning on page 80 or contact the BT6610
Helpline on 0800 145 6789*. Additional answers to
frequently asked questions are available from
bt.com/producthelp
In the unlikely event of a defect occurring, the helpdesk
will issue a Fault Reference Authorisation (FRA) number
and instructions for replacement or repair. Please note
you will need the FRA number before returning the
product. This does not affect your statutory rights.
Outside of the 12 month guarantee period
If your product needs repair after the guarantee
period has ended, the repair must meet the approval
requirements for connection to the telephone network.
We recommend that you contact BT’s recommended
repair agent Discount Communications on 0800 980
8999 or a local qualiﬁed repairer.
Returning your phone
If the Helpline is unable to remedy your problem they
will issue a Fault Reference Authorisation number and
ask you to return the product to your original place
of purchase. Where possible, pack the product in its
original packaging. Please remember to include all
parts, including the line cords, power supply units and
the original batteries.

General information 90
Technical information
How many telephones can I have?
All items of telephone equipment have a Ringer
Equivalence Number (REN), which is used to calculate
the number of items which may be connected to any
one telephone line. Your BT6610 has a REN of 1. A total
REN of 4 is allowed. If the total REN of 4 is exceeded,
the telephones may not ring. With different telephone
types there is no guarantee of ringing, even when the
REN is less than 4.
Any additional handsets and chargers that you register
have a REN of 0.
Connecting to a switchboard
Switchboard compatibility
This telephone may be connected to most types of
switchboard, however in the event of any difﬁculties,
consult your switchboard Service Provider.
Recall (R)
Recall is used when connected to certain switchboards/
PBXs and some BT Calling Features, or those services
available via your network provider. The BT6610
supports time break recall but not earth loop recall.
R&TTE
This product is intended for use within the UK for
connection to the public telephone network and
compatible switchboards.
This equipment complies with the essential
requirements for the Radio Equipment and
Telecommunications Terminal Equipment Directive
(1999/5/EC).
Declaration of Conformance
Hereby, BT declares that this BT6610 is in compliance
with the essential requirements and other relevant
provisions of Directive 1999/5/EC.
If you would like a copy of the Declaration of
Conformance, please visit bt.com/producthelp
For your records
Date of purchase:
Place of purchase:
For guarantee purposes, proof of purchase is required,
so please keep your receipt.
Enter your base system PIN here:
[ / / / ]
Enter your remote access PIN here:
[ / / / ]

Offices worldwide
The services described in this publication are subject to availability
and may be modified from time to time. Services and equipment
are provided subject to British Telecommunications plc’s respective
standard conditions of contract. Nothing in this publication forms
any part of any contract.
© British Telecommunications plc 2015.
Registered Office: 81 Newgate Street, London EC1A 7AJ.
Registered in England No. 1800000.
Printed in China.
Designed by The Art & Design Partnership.
Available in other formats including braille, large print or audio CD.
If you would like a copy, please call 0800 145 6789*.
* Calls made from within the UK mainland network are free.
Mobile and international call costs may vary.
BT6610 (12/15) Issue 1
For a Better Future
We’re always looking to make our products last longer
and use less power, so we don’t have such a big impact
on the environment.
To find out about what we are doing, visit
bt.com/betterfuture

BT 6610 Digital Cordless Phone User Guide

More Related Content

Viewers also liked (11)

Similar to BT 6610 Digital Cordless Phone User Guide (20)

More from Telephones Online (20)

Recently uploaded (20)

BT 6610 Digital Cordless Phone User Guide