Ch 18 intro to network layer - section 3

 NETWORK-LAYER PERFORMANCE:
-Delay.
-Throughput.
-Packet Loss.
 NETWORK-LAYER PERFORMANCE IMPROVEMENT:
-Congestion Control

 The performance of a network can be
measured in terms of delay, throughput, and
packet loss.
 When the load is much less than the capacity
of the network, the delay is at a minimum.
 Congestion control is an issue that can
improve the performance.

 A sender cannot send a packet instantaneously, but
needs to put the bits in a packet on one line by one.
 The first bit of the packet is put on the line at time
t1 and the last bit is put on the line at time t2,
transmission delay of the packet is (t2 − t1).
 the transmission delay is longer for a longer packet
and shorter if sender can transmit faster.
 Delaytr = (Packet length) / (Transmission rate).

 Propagation delay is the time it takes for a
bit to travel from point A to point B in the
transmission media.
 Depends on:
-The propagation delay of each network (LAN or WAN).
-The propagation speed of the media.
-The distance of the link.
 Delaypg = (Distance) / (Propagation speed).

 The processing delay is the time required for
a router or a destination host to:
-receive a packet from its input port.
-remove the header.
-perform an error detection procedure.
-And deliver the packet to the output port.
 The processing delay may be different for each
packet, but normally is calculated as an average.
 Delaypr = Time required to process a packet in
a router or a destination host.
 propagation delay and processing delay,both of
which are negligible.

 Queuing delay can normally happen in a router.
 The queuing delay for a packet in a router is measured
as the time a packet waits in the input queue and
output queue of a router.
 Delayqu = The time a packet waits in input and
output queues in a router.
 Total delay = (n + 1) (Delaytr + Delaypg + Delaypr) +
(n) (Delayqu)

 The number of bits passing through a point in a
second.
 The transmission rate of data at that point.
 packet may pass through several links, each with
a different transmission rate.
 Throughput = minimum {TR1, TR2, . . . TRn}.

For example,
In Figure the transmission rate of the main link in the
calculation of the throughput is only 200 kbps
because the link is shared between three paths.

 When a router receives a packet while processing
another packet, the received packet needs to be
stored in the input buffer waiting for its turn.
 When the buffer is full and the next packet needs
to be dropped.
 A lot of theoretical studies have been done in
queuing theory to prevent the overflow of queues
and prevent packet loss.

 Congestion control is a mechanism for improving
performance.
 When the buffer is full and the next packet needs
to be dropped.
 Discarding packets does not reduce the number of
packets in the network because the sources
retransmit the packets, using time-out mechanisms,
when the packets do not reach the destinations.

 Congestion at the network layer is related to two issues,
throughput and delay.
 Note that the delay becomes infinite when the load is greater
than the capacity.
 When the load is below the capacity of the network, the
throughput increases proportionally with the load, after the
load reaches the capacity, the throughput declines sharply.

 open-loop congestion control prevent congestion
before it happens:
1. Retransmission Policy
2. Window Policy
3. Acknowledgment Policy
4. Discarding Policy
5. Admission Policy
 closed-loop congestion control remove congestion
after it has happened:
1. Backpressure
2. Choke Packet
3. Implicit Signaling
4. Explicit Signaling

 The retransmission policy and the retransmission timers
must be designed to optimize efficiency and at the same
time prevent congestion.
 Window Policy:
Go-Back-N window, when the timer for a packet times out,
several packets may be resent, although some may have
arrived safe and sound at the receiver.
The Selective Repeat window, tries to send the specific
packets that have been lost or corrupted.
Selective Repeat window is better than the Go-Back-N
window for congestion control.

 The acknowledgment policy imposed by the receiver
may also affect congestion.
 If the receiver does not acknowledge every packet it
receives, it may slow down the sender and help
prevent congestion.
 A receiver may send an acknowledgment only if it has
a packet to be sent or a special timer expires.
 A receiver may decide to acknowledge only N packets
at a time.
 acknowledgments means imposing less load on the
network.

 A good discarding policy by the routers may prevent congestion
and at the same time may not harm the integrity of the
transmission.
For example: audio transmission, if the policy is to discard less
sensitive packets when congestion is likely to happen, the
quality of sound is still preserved and congestion is prevented.
 An admission policy, which is a quality-of-service mechanism
can also prevent congestion in virtual-circuit networks.
 A router can deny establishing a virtual-circuit connection if
there is congestion in the network or if there is a possibility of
future congestion.

 The technique of Backpressure refers to a congestion control
mechanism in which a congested node stops receiving data
from the immediate upstream node or nodes.
 This may cause the upstream node or nodes to become
congested, and they, in turn, reject data from their upstream
node or nodes, and so on.
 The backpressure technique can be applied only to virtual
circuit networks, in which each node knows the upstream
node from which a flow of data is coming.

 A Choke packet is a packet sent by a node to the
source to inform it of congestion.
 In the choke-packet method, the warning is from
the router, which has encountered congestion,
directly to the source station.
 The intermediate nodes through which the
packet has traveled are not warned.

 In Implicit signaling, there is no communication
between the congested node or nodes and the
source.
 The source guesses that there is congestion
somewhere in the network from other symptoms.
 For example, when a source sends several packets
and there is no acknowledgment for a while, one
assumption is that the network is congested.
 The delay in receiving an acknowledgment is
interpreted as congestion in the network; the
source should slow down.

 The node that congestion can explicitly send
a signal to the source or destination.
 In the Explicit-signaling method, the signal is
included in the packets that carry data.
 Explicit signaling can occur in either the
forward or the backward direction.

Ch 18 intro to network layer - section 3

More Related Content

What's hot (20)

Viewers also liked (20)

Similar to Ch 18 intro to network layer - section 3 (20)

Recently uploaded (20)

Ch 18 intro to network layer - section 3